#include "dhd_dbg.h"
#include "wl_cfg80211.h"
-#if !defined(SDIO_VENDOR_ID_BROADCOM)
#define SDIO_VENDOR_ID_BROADCOM 0x02d0
-#endif /* !defined(SDIO_VENDOR_ID_BROADCOM) */
#define DMA_ALIGN_MASK 0x03
-#if !defined(SDIO_DEVICE_ID_BROADCOM_4329)
#define SDIO_DEVICE_ID_BROADCOM_4329 0x4329
-#endif /* !defined(SDIO_DEVICE_ID_BROADCOM_4329) */
static int brcmf_sdioh_get_cisaddr(struct brcmf_sdio_dev *sdiodev, u32 regaddr);
static int brcmf_ops_sdio_probe(struct sdio_func *func,
char iface_name[IFNAMSIZ] = "wlan";
module_param_string(iface_name, iface_name, IFNAMSIZ, 0);
-/* The following are specific to the SDIO dongle */
-
-#ifdef SDTEST
-/* Echo packet generator (pkts/s) */
-uint brcmf_pktgen;
-module_param(brcmf_pktgen, uint, 0);
-
-/* Echo packet len (0 => sawtooth, max 2040) */
-uint brcmf_pktgen_len;
-module_param(brcmf_pktgen_len, uint, 0);
-#endif
-
static int brcmf_toe_get(struct brcmf_info *drvr_priv, int idx, u32 *toe_ol);
static int brcmf_toe_set(struct brcmf_info *drvr_priv, int idx, u32 toe_ol);
static int brcmf_host_event(struct brcmf_info *drvr_priv, int *ifidx,
static int brcmf_netdev_stop(struct net_device *net)
{
-#if !defined(IGNORE_ETH0_DOWN)
struct brcmf_info *drvr_priv = *(struct brcmf_info **) netdev_priv(net);
brcmf_dbg(TRACE, "Enter\n");
/* Set state and stop OS transmissions */
drvr_priv->pub.up = 0;
netif_stop_queue(net);
-#else
- brcmf_dbg(ERROR, "BYPASSed due to BRCM compilation: under investigation\n");
-#endif /* !defined(IGNORE_ETH0_DOWN) */
return 0;
}
#ifndef _BRCMF_PROTO_H_
#define _BRCMF_PROTO_H_
-#ifndef IOCTL_RESP_TIMEOUT
#define IOCTL_RESP_TIMEOUT 2000 /* In milli second */
-#endif
-
-#ifndef IOCTL_CHIP_ACTIVE_TIMEOUT
#define IOCTL_CHIP_ACTIVE_TIMEOUT 10 /* In milli second */
-#endif
/*
* Exported from the brcmf protocol module (brcmf_cdc)
* for HT availability, it could take a couple hundred ms more, so
* max out at a 1 second (1000000us).
*/
-#if (PMU_MAX_TRANSITION_DLY <= 1000000)
#undef PMU_MAX_TRANSITION_DLY
#define PMU_MAX_TRANSITION_DLY 1000000
-#endif
/* Value for ChipClockCSR during initial setup */
#define BRCMF_INIT_CLKCTL1 (SBSDIO_FORCE_HW_CLKREQ_OFF | \
brcmf_sdcard_cfg_write(bus->sdiodev, SDIO_FUNC_1,
SBSDIO_FUNC1_CHIPCLKCSR, saveclk, &err);
-#if defined(OOB_INTR_ONLY)
- /* Host registration for OOB interrupt */
- if (brcmf_sdio_register_oob_intr(bus->dhd)) {
- brcmf_sdbrcm_wd_timer(bus, 0);
- brcmf_dbg(ERROR, "Host failed to resgister for OOB\n");
- ret = -ENODEV;
- goto exit;
- }
-
- /* Enable oob at firmware */
- brcmf_sdbrcm_enable_oob_intr(bus, true);
-#endif /* defined(OOB_INTR_ONLY) */
-
/* If we didn't come up, turn off backplane clock */
if (drvr->busstate != BRCMF_BUS_DATA)
brcmf_sdbrcm_clkctl(bus, CLK_NONE, false);
if (!bus->intr)
brcmf_dbg(ERROR, "isr w/o interrupt configured!\n");
-#if defined(SDIO_ISR_THREAD)
- brcmf_dbg(TRACE, "Calling brcmf_sdbrcm_dpc()\n");
- while (brcmf_sdbrcm_dpc(bus))
- ;
-#else
bus->dpc_sched = true;
brcmf_sdbrcm_sched_dpc(bus);
-#endif
-
}
extern bool brcmf_sdbrcm_bus_watchdog(struct brcmf_pub *drvr)
wdev->wiphy->signal_type = CFG80211_SIGNAL_TYPE_MBM;
wdev->wiphy->cipher_suites = __wl_cipher_suites;
wdev->wiphy->n_cipher_suites = ARRAY_SIZE(__wl_cipher_suites);
-#ifndef WL_POWERSAVE_DISABLED
wdev->wiphy->flags |= WIPHY_FLAG_PS_ON_BY_DEFAULT; /* enable power
* save mode
* by default
*/
-#else
- wdev->wiphy->flags &= ~WIPHY_FLAG_PS_ON_BY_DEFAULT;
-#endif /* !WL_POWERSAVE_DISABLED */
err = wiphy_register(wdev->wiphy);
if (unlikely(err < 0)) {
WL_ERR("Couldn not register wiphy device (%d)\n", err);
s32 err = 0;
cfg_priv->scan_request = NULL;
-#ifndef WL_POWERSAVE_DISABLED
cfg_priv->pwr_save = true;
-#endif /* WL_POWERSAVE_DISABLED */
cfg_priv->iscan_on = true; /* iscan on & off switch.
we enable iscan per default */
cfg_priv->roam_on = true; /* roam on & off switch.
#include <chipcommon.h>
#include <brcmu_utils.h>
#include <brcm_hw_ids.h>
+#include <soc.h>
#include "types.h"
#include "pub.h"
#include "pmu.h"
/* Region 2 for sdram (512 MB) */
#define SI_SDRAM_R2 0x80000000
-#ifdef SI_ENUM_BASE_VARIABLE
-#define SI_ENUM_BASE (sii->pub.si_enum_base)
-#else
-#define SI_ENUM_BASE 0x18000000 /* Enumeration space base */
-#endif /* SI_ENUM_BASE_VARIABLE */
-
/* Wrapper space base */
#define SI_WRAP_BASE 0x18100000
/* each core gets 4Kbytes for registers */
#define DEFAULT_GPIO_ONTIME 10 /* Default: 10% on */
#define DEFAULT_GPIO_OFFTIME 90 /* Default: 10% on */
-#ifndef DEFAULT_GPIOTIMERVAL
#define DEFAULT_GPIOTIMERVAL \
((DEFAULT_GPIO_ONTIME << GPIO_ONTIME_SHIFT) | DEFAULT_GPIO_OFFTIME)
-#endif
/*
* Data structure to export all chip specific common variables
#define SI_PCIUP 3
/* PMU clock/power control */
-#if defined(BCMPMUCTL)
-#define PMUCTL_ENAB(sih) (BCMPMUCTL)
-#else
#define PMUCTL_ENAB(sih) ((sih)->cccaps & CC_CAP_PMU)
-#endif
/* chipcommon clock/power control (exclusive with PMU's) */
-#if defined(BCMPMUCTL) && BCMPMUCTL
-#define CCCTL_ENAB(sih) (0)
-#define CCPLL_ENAB(sih) (0)
-#else
#define CCCTL_ENAB(sih) ((sih)->cccaps & CC_CAP_PWR_CTL)
#define CCPLL_ENAB(sih) ((sih)->cccaps & CC_CAP_PLL_MASK)
-#endif
/* External PA enable mask */
#define GPIO_CTRL_EPA_EN_MASK 0x40
static const struct locale_mimo_info *brcms_c_get_mimo_5g(u8 locale_idx);
/* QDB() macro takes a dB value and converts to a quarter dB value */
-#ifdef QDB
-#undef QDB
-#endif
#define QDB(n) ((n) * BRCMS_TXPWR_DB_FACTOR)
/* Regulatory Matrix Spreadsheet (CLM) MIMO v3.7.9 */
&locale_11n
};
-#ifdef LC
-#undef LC
-#endif
#define LC(id) LOCALE_MIMO_IDX_ ## id
-#ifdef LC_2G
-#undef LC_2G
-#endif
#define LC_2G(id) LOCALE_2G_IDX_ ## id
-#ifdef LC_5G
-#undef LC_5G
-#endif
#define LC_5G(id) LOCALE_5G_IDX_ ## id
#define LOCALES(band2, band5, mimo2, mimo5) \
#define TX_DATA_FIFO TX_AC_BE_FIFO
#define TX_CTL_FIFO TX_AC_VO_FIFO
-#ifndef WL_RSSI_ANT_MAX
#define WL_RSSI_ANT_MAX 4 /* max possible rx antennas */
-#elif WL_RSSI_ANT_MAX != 4
-#error "WL_RSSI_ANT_MAX does not match"
-#endif
struct intctrlregs {
u32 intstatus;
struct tasklet_struct tasklet; /* dpc tasklet */
bool resched; /* dpc needs to be and is rescheduled */
-#ifdef LINUXSTA_PS
- u32 pci_psstate[16]; /* pci ps-state save/restore */
-#endif
struct brcms_firmware fw;
struct wiphy *wiphy;
};
/* if primary config, we need to update BSSID in RXE match registers */
if (cfg == wlc->cfg)
brcms_c_set_addrmatch(wlc, RCM_BSSID_OFFSET, cfg->BSSID);
-#ifdef SUPPORT_HWKEYS
- else if (BSSCFG_STA(cfg) && cfg->BSS)
- brcms_c_rcmta_add_bssid(wlc, cfg);
-
-#endif
}
void brcms_b_set_shortslot(struct brcms_hardware *wlc_hw, bool shortslot)
break;
}
}
-#if NCONF
+
/*
* pick siso/cdd as default for OFDM (note no basic
* rate MCSs are supported yet)
if (IS_OFDM(lowest_basic_rspec))
lowest_basic_rspec |= (wlc->stf->ss_opmode << RSPEC_STF_SHIFT);
-#endif
-
return lowest_basic_rspec;
}
/* WME QoS mode is Auto by default */
wlc->pub->_wme = AUTO;
-
-#ifdef BCMSDIODEV_ENABLED
- /* enable priority flow control for sdio dongle */
- wlc->pub->_priofc = true;
-#endif
-
wlc->pub->_ampdu = AMPDU_AGG_HOST;
wlc->pub->bcmerror = 0;
wlc->pub->_coex = ON;
else
rspec[k] |= (mimo_ctlchbw << RSPEC_BW_SHIFT);
- /* Set Short GI */
-#ifdef NOSGIYET
- if (IS_MCS(rspec[k])
- && (txrate[k]->flags & IEEE80211_TX_RC_SHORT_GI))
- rspec[k] |= RSPEC_SHORT_GI;
- else if (!(txrate[k]->flags & IEEE80211_TX_RC_SHORT_GI))
- rspec[k] &= ~RSPEC_SHORT_GI;
-#else
+ /* Disable short GI, not supported yet */
rspec[k] &= ~RSPEC_SHORT_GI;
-#endif
mimo_preamble_type = BRCMS_MM_PREAMBLE;
if (txrate[k]->flags & IEEE80211_TX_RC_GREEN_FIELD)
brcms_c_txflowcontrol_signal(struct brcms_c_info *wlc,
struct brcms_txq_info *qi, bool on, int prio)
{
-#ifdef NON_FUNCTIONAL
- /* wlcif_list is never filled so this function is not functional */
- struct brcms_c_if *wlcif;
-
- for (wlcif = wlc->wlcif_list; wlcif != NULL; wlcif = wlcif->next) {
- if (wlcif->qi == qi && wlcif->flags & BRCMS_IF_LINKED)
- brcms_txflowcontrol(wlc->wl, wlcif->wlif, on, prio);
- }
-#endif
+ /* wlcif_list is never filled so this function is not functional yet */
}
static struct brcms_txq_info *brcms_c_txq_alloc(struct brcms_c_info *wlc)
#define ANTSWITCH_TYPE_3 3
#define RXBUFSZ PKTBUFSZ
-#ifndef AIDMAPSZ
/* aid bitmap size in bytes */
#define AIDMAPSZ (roundup(MAXSCB, NBBY)/NBBY)
-#endif /* AIDMAPSZ */
#define MAX_STREAMS_SUPPORTED 4 /* max number of streams supported */
#define SUPPORT_11N (ENAB_1x1|ENAB_2x2)
#define SUPPORT_HT (ENAB_1x1|ENAB_2x2|ENAB_3x3)
/* WL11N Support */
-#if ((defined(NCONF) && (NCONF != 0)) || \
- (defined(LCNCONF) && (LCNCONF != 0)) || \
- (defined(HTCONF) && (HTCONF != 0)) || \
- (defined(SSLPNCONF) && (SSLPNCONF != 0)))
#define N_ENAB(pub) ((pub)->_n_enab & SUPPORT_11N)
#define N_REQD(pub) ((pub)->_n_reqd)
-#else
-#define N_ENAB(pub) 0
-#define N_REQD(pub) 0
-#endif
-
-#if (defined(HTCONF) && (HTCONF != 0))
-#define HT_ENAB(pub) (((pub)->_n_enab & SUPPORT_HT) == SUPPORT_HT)
-#else
+
#define HT_ENAB(pub) 0
-#endif
#define AMPDU_AGG_HOST 1
#define AMPDU_ENAB(pub) ((pub)->_ampdu)
#include <linux/types.h>
#include <linux/io.h>
-#if 0
-/* Bus types */
-#define SDIO_BUS 3 /* SDIO target */
-#define USB_BUS 5 /* USB (does not support R/W REG) */
-#define SPI_BUS 6 /* gSPI target */
-#define RPC_BUS 7 /* RPC target */
-#endif
-
#define WL_CHAN_FREQ_RANGE_2G 0
#define WL_CHAN_FREQ_RANGE_5GL 1
#define WL_CHAN_FREQ_RANGE_5GM 2
}
/* osl multi-precedence packet queue */
-#ifndef PKTQ_LEN_DEFAULT
#define PKTQ_LEN_DEFAULT 128 /* Max 128 packets */
-#endif
-#ifndef PKTQ_MAX_PREC
#define PKTQ_MAX_PREC 16 /* Maximum precedence levels */
-#endif
struct pktq_prec {
struct sk_buff *head; /* first packet to dequeue */
#define BCME_STRLEN 64 /* Max string length for BCM errors */
-#ifndef ABS
#define ABS(a) (((a) < 0) ? -(a) : (a))
-#endif /* ABS */
#define CEIL(x, y) (((x) + ((y)-1)) / (y))
#define ISPOWEROF2(x) ((((x)-1)&(x)) == 0)
#define USB_BUS 5
#define SPI_BUS 6
-#ifndef OFF
#define OFF 0
-#endif
-
-#ifndef ON
#define ON 1 /* ON = 1 */
-#endif
-
#define AUTO (-1) /* Auto = -1 */
/*
#ifndef _BRCM_SOC_H
#define _BRCM_SOC_H
-#ifdef SI_ENUM_BASE_VARIABLE
-#define SI_ENUM_BASE (sii->pub.si_enum_base)
-#else
#define SI_ENUM_BASE 0x18000000 /* Enumeration space base */
-#endif /* SI_ENUM_BASE_VARIABLE */
/* core codes */
#define NODEV_CORE_ID 0x700 /* Invalid coreid */
projects / GitHub / mt8127 / android_kernel_alcatel_ttab.git / commitdiff