i8042.notimeout [HW] Ignore timeout condition signalled by controller
i8042.reset [HW] Reset the controller during init and cleanup
i8042.unlock [HW] Unlock (ignore) the keylock
+ i8042.kbdreset [HW] Reset device connected to KBD port
i810= [HW,DRM]
VERSION = 3
PATCHLEVEL = 10
-SUBLEVEL = 65
+SUBLEVEL = 66
EXTRAVERSION =
NAME = TOSSUG Baby Fish
/* this is for console on PGU */
/* bootargs = "console=tty0 consoleblank=0"; */
/* this is for console on serial */
- bootargs = "earlycon=uart8250,mmio32,0xc0000000,115200n8 console=tty0 console=ttyS0,115200n8 consoleblank=0 debug";
+ bootargs = "earlycon=uart8250,mmio32,0xf0000000,115200n8 console=tty0 console=ttyS0,115200n8 consoleblank=0 debug";
};
aliases {
#interrupt-cells = <1>;
};
- uart0: serial@c0000000 {
+ uart0: serial@f0000000 {
compatible = "ns8250";
- reg = <0xc0000000 0x2000>;
+ reg = <0xf0000000 0x2000>;
interrupts = <11>;
clock-frequency = <3686400>;
baud = <115200>;
no-loopback-test = <1>;
};
- pgu0: pgu@c9000000 {
+ pgu0: pgu@f9000000 {
compatible = "snps,arcpgufb";
- reg = <0xc9000000 0x400>;
+ reg = <0xf9000000 0x400>;
};
- ps2: ps2@c9001000 {
+ ps2: ps2@f9001000 {
compatible = "snps,arc_ps2";
- reg = <0xc9000400 0x14>;
+ reg = <0xf9000400 0x14>;
interrupts = <13>;
interrupt-names = "arc_ps2_irq";
};
- eth0: ethernet@c0003000 {
+ eth0: ethernet@f0003000 {
compatible = "snps,oscilan";
- reg = <0xc0003000 0x44>;
+ reg = <0xf0003000 0x44>;
interrupts = <7>, <8>;
interrupt-names = "rx", "tx";
};
#size-cells = <0>;
compatible = "fsl,imx25-cspi", "fsl,imx35-cspi";
reg = <0x43fa4000 0x4000>;
- clocks = <&clks 62>, <&clks 62>;
+ clocks = <&clks 78>, <&clks 78>;
clock-names = "ipg", "per";
interrupts = <14>;
status = "disabled";
post_div_table[1].div = 1;
post_div_table[2].div = 1;
video_div_table[1].div = 1;
- video_div_table[2].div = 1;
- };
+ video_div_table[3].div = 1;
+ }
/* type name parent_name base div_mask */
clk[pll1_sys] = imx_clk_pllv3(IMX_PLLV3_SYS, "pll1_sys", "osc", base, 0x7f);
rate = clk_get_rate(sys_clk);
/* Numerator/denumerator values refer TRM Realtime Counter section */
switch (rate) {
- case 1200000:
+ case 12000000:
num = 64;
den = 125;
break;
- case 1300000:
+ case 13000000:
num = 768;
den = 1625;
break;
num = 8;
den = 25;
break;
- case 2600000:
+ case 26000000:
num = 384;
den = 1625;
break;
- case 2700000:
+ case 27000000:
num = 256;
den = 1125;
break;
static struct renesas_intc_irqpin_config irqpin0_platform_data = {
.irq_base = irq_pin(0), /* IRQ0 -> IRQ7 */
+ .control_parent = true,
};
static struct resource irqpin0_resources[] = {
static struct renesas_intc_irqpin_config irqpin2_platform_data = {
.irq_base = irq_pin(16), /* IRQ16 -> IRQ23 */
+ .control_parent = true,
};
static struct resource irqpin2_resources[] = {
static struct renesas_intc_irqpin_config irqpin3_platform_data = {
.irq_base = irq_pin(24), /* IRQ24 -> IRQ31 */
+ .control_parent = true,
};
static struct resource irqpin3_resources[] = {
default y
select HAVE_GENERIC_HARDIRQS
select HAVE_UID16
+ select HAVE_FUTEX_CMPXCHG if FUTEX
select GENERIC_IRQ_SHOW
select GENERIC_CPU_DEVICES
select GENERIC_IO
regs->flags &= ~X86_EFLAGS_IF;
trace_hardirqs_off();
regs->ip = (unsigned long)(jp->entry);
+
+ /*
+ * jprobes use jprobe_return() which skips the normal return
+ * path of the function, and this messes up the accounting of the
+ * function graph tracer to get messed up.
+ *
+ * Pause function graph tracing while performing the jprobe function.
+ */
+ pause_graph_tracing();
return 1;
}
struct kprobe_ctlblk *kcb = get_kprobe_ctlblk();
u8 *addr = (u8 *) (regs->ip - 1);
struct jprobe *jp = container_of(p, struct jprobe, kp);
+ void *saved_sp = kcb->jprobe_saved_sp;
if ((addr > (u8 *) jprobe_return) &&
(addr < (u8 *) jprobe_return_end)) {
- if (stack_addr(regs) != kcb->jprobe_saved_sp) {
+ if (stack_addr(regs) != saved_sp) {
struct pt_regs *saved_regs = &kcb->jprobe_saved_regs;
printk(KERN_ERR
"current sp %p does not match saved sp %p\n",
- stack_addr(regs), kcb->jprobe_saved_sp);
+ stack_addr(regs), saved_sp);
printk(KERN_ERR "Saved registers for jprobe %p\n", jp);
show_regs(saved_regs);
printk(KERN_ERR "Current registers\n");
show_regs(regs);
BUG();
}
+ /* It's OK to start function graph tracing again */
+ unpause_graph_tracing();
*regs = kcb->jprobe_saved_regs;
- memcpy((kprobe_opcode_t *)(kcb->jprobe_saved_sp),
- kcb->jprobes_stack,
- MIN_STACK_SIZE(kcb->jprobe_saved_sp));
+ memcpy(saved_sp, kcb->jprobes_stack, MIN_STACK_SIZE(saved_sp));
preempt_enable_no_resched();
return 1;
}
extern asmlinkage void sys_ni_syscall(void);
-const sys_call_ptr_t sys_call_table[] __cacheline_aligned = {
+const sys_call_ptr_t sys_call_table[] ____cacheline_aligned = {
/*
* Smells like a compiler bug -- it doesn't work
* when the & below is removed.
extern void sys_ni_syscall(void);
-const sys_call_ptr_t sys_call_table[] __cacheline_aligned = {
+const sys_call_ptr_t sys_call_table[] ____cacheline_aligned = {
/*
* Smells like a compiler bug -- it doesn't work
* when the & below is removed.
*/
#include <linux/device.h>
+#include <linux/err.h>
#include <linux/errno.h>
#include <linux/module.h>
#include <linux/io.h>
return false;
ret = gc->of_xlate(gc, &gg_data->gpiospec, gg_data->flags);
- if (ret < 0)
- return false;
+ if (ret < 0) {
+ /* We've found the gpio chip, but the translation failed.
+ * Return true to stop looking and return the translation
+ * error via out_gpio
+ */
+ gg_data->out_gpio = ERR_PTR(ret);
+ return true;
+ }
gg_data->out_gpio = ret + gc->base;
return true;
#define PIPE_CONTROL_GLOBAL_GTT_IVB (1<<24) /* gen7+ */
#define PIPE_CONTROL_CS_STALL (1<<20)
#define PIPE_CONTROL_TLB_INVALIDATE (1<<18)
+#define PIPE_CONTROL_MEDIA_STATE_CLEAR (1<<16)
#define PIPE_CONTROL_QW_WRITE (1<<14)
#define PIPE_CONTROL_DEPTH_STALL (1<<13)
#define PIPE_CONTROL_WRITE_FLUSH (1<<12)
flags |= PIPE_CONTROL_VF_CACHE_INVALIDATE;
flags |= PIPE_CONTROL_CONST_CACHE_INVALIDATE;
flags |= PIPE_CONTROL_STATE_CACHE_INVALIDATE;
+ flags |= PIPE_CONTROL_MEDIA_STATE_CLEAR;
/*
* TLB invalidate requires a post-sync write.
*/
flags |= PIPE_CONTROL_QW_WRITE;
flags |= PIPE_CONTROL_GLOBAL_GTT_IVB;
+ flags |= PIPE_CONTROL_STALL_AT_SCOREBOARD;
+
/* Workaround: we must issue a pipe_control with CS-stall bit
* set before a pipe_control command that has the state cache
* invalidate bit set. */
struct radeon_connector_atom_dig *dig_connector;
int dp_clock;
+ if ((mode->clock > 340000) &&
+ (!radeon_connector_is_dp12_capable(connector)))
+ return MODE_CLOCK_HIGH;
+
if (!radeon_connector->con_priv)
return MODE_CLOCK_HIGH;
dig_connector = radeon_connector->con_priv;
rbo = container_of(bo, struct radeon_bo, tbo);
switch (bo->mem.mem_type) {
case TTM_PL_VRAM:
- if (rbo->rdev->ring[RADEON_RING_TYPE_GFX_INDEX].ready == false)
+ if (rbo->rdev->ring[radeon_copy_ring_index(rbo->rdev)].ready == false)
radeon_ttm_placement_from_domain(rbo, RADEON_GEM_DOMAIN_CPU);
else
radeon_ttm_placement_from_domain(rbo, RADEON_GEM_DOMAIN_GTT);
if (ret != 0)
goto out_no_queue;
+ return 0;
+
out_no_queue:
event->base.destroy(&event->base);
out_no_event:
BUG_ON(fence == NULL);
- if (arg->flags & DRM_VMW_FE_FLAG_REQ_TIME)
- ret = vmw_event_fence_action_create(file_priv, fence,
- arg->flags,
- arg->user_data,
- true);
- else
- ret = vmw_event_fence_action_create(file_priv, fence,
- arg->flags,
- arg->user_data,
- true);
-
+ ret = vmw_event_fence_action_create(file_priv, fence,
+ arg->flags,
+ arg->user_data,
+ true);
if (unlikely(ret != 0)) {
if (ret != -ERESTARTSYS)
DRM_ERROR("Failed to attach event to fence.\n");
DMI_MATCH(DMI_PRODUCT_NAME, "Aspire 1360"),
},
},
+ {
+ /* Acer Aspire 7738 */
+ .matches = {
+ DMI_MATCH(DMI_SYS_VENDOR, "Acer"),
+ DMI_MATCH(DMI_PRODUCT_NAME, "Aspire 7738"),
+ },
+ },
{
/* Gericom Bellagio */
.matches = {
{ }
};
+/*
+ * Some laptops need keyboard reset before probing for the trackpad to get
+ * it detected, initialised & finally work.
+ */
+static const struct dmi_system_id __initconst i8042_dmi_kbdreset_table[] = {
+ {
+ /* Gigabyte P35 v2 - Elantech touchpad */
+ .matches = {
+ DMI_MATCH(DMI_SYS_VENDOR, "GIGABYTE"),
+ DMI_MATCH(DMI_PRODUCT_NAME, "P35V2"),
+ },
+ },
+ {
+ /* Aorus branded Gigabyte X3 Plus - Elantech touchpad */
+ .matches = {
+ DMI_MATCH(DMI_SYS_VENDOR, "GIGABYTE"),
+ DMI_MATCH(DMI_PRODUCT_NAME, "X3"),
+ },
+ },
+ {
+ /* Gigabyte P34 - Elantech touchpad */
+ .matches = {
+ DMI_MATCH(DMI_SYS_VENDOR, "GIGABYTE"),
+ DMI_MATCH(DMI_PRODUCT_NAME, "P34"),
+ },
+ },
+ { }
+};
+
#endif /* CONFIG_X86 */
#ifdef CONFIG_PNP
if (dmi_check_system(i8042_dmi_dritek_table))
i8042_dritek = true;
+ if (dmi_check_system(i8042_dmi_kbdreset_table))
+ i8042_kbdreset = true;
+
/*
* A20 was already enabled during early kernel init. But some buggy
* BIOSes (in MSI Laptops) require A20 to be enabled using 8042 to
module_param_named(notimeout, i8042_notimeout, bool, 0);
MODULE_PARM_DESC(notimeout, "Ignore timeouts signalled by i8042");
+static bool i8042_kbdreset;
+module_param_named(kbdreset, i8042_kbdreset, bool, 0);
+MODULE_PARM_DESC(kbdreset, "Reset device connected to KBD port");
+
#ifdef CONFIG_X86
static bool i8042_dritek;
module_param_named(dritek, i8042_dritek, bool, 0);
if (i8042_toggle_aux(true))
return -1;
+/*
+ * Reset keyboard (needed on some laptops to successfully detect
+ * touchpad, e.g., some Gigabyte laptop models with Elantech
+ * touchpads).
+ */
+ if (i8042_kbdreset) {
+ pr_warn("Attempting to reset device connected to KBD port\n");
+ i8042_kbd_write(NULL, (unsigned char) 0xff);
+ }
+
/*
* Test AUX IRQ delivery to make sure BIOS did not grab the IRQ and
* used it for a PCI card or somethig else.
{
dev_dbg(dev, "pre_pll_clk_div\t%d\n", pll->pre_pll_clk_div);
dev_dbg(dev, "pll_multiplier \t%d\n", pll->pll_multiplier);
- if (pll->flags != SMIAPP_PLL_FLAG_NO_OP_CLOCKS) {
+ if (!(pll->flags & SMIAPP_PLL_FLAG_NO_OP_CLOCKS)) {
dev_dbg(dev, "op_sys_clk_div \t%d\n", pll->op_sys_clk_div);
dev_dbg(dev, "op_pix_clk_div \t%d\n", pll->op_pix_clk_div);
}
dev_dbg(dev, "ext_clk_freq_hz \t%d\n", pll->ext_clk_freq_hz);
dev_dbg(dev, "pll_ip_clk_freq_hz \t%d\n", pll->pll_ip_clk_freq_hz);
dev_dbg(dev, "pll_op_clk_freq_hz \t%d\n", pll->pll_op_clk_freq_hz);
- if (pll->flags & SMIAPP_PLL_FLAG_NO_OP_CLOCKS) {
+ if (!(pll->flags & SMIAPP_PLL_FLAG_NO_OP_CLOCKS)) {
dev_dbg(dev, "op_sys_clk_freq_hz \t%d\n",
pll->op_sys_clk_freq_hz);
dev_dbg(dev, "op_pix_clk_freq_hz \t%d\n",
pll->flags |= SMIAPP_PLL_FLAG_OP_PIX_CLOCK_PER_LANE;
pll->scale_n = sensor->limits[SMIAPP_LIMIT_SCALER_N_MIN];
+ mutex_lock(&sensor->mutex);
rval = smiapp_update_mode(sensor);
+ mutex_unlock(&sensor->mutex);
if (rval) {
dev_err(&client->dev, "update mode failed\n");
goto out_nvm_release;
err("usb_register failed. (%d)", result);
return result;
}
+#if IS_MODULE(CONFIG_DVB_USB_AF9005) || defined(CONFIG_DVB_USB_AF9005_REMOTE)
+ /* FIXME: convert to todays kernel IR infrastructure */
rc_decode = symbol_request(af9005_rc_decode);
rc_keys = symbol_request(rc_map_af9005_table);
rc_keys_size = symbol_request(rc_map_af9005_table_size);
+#endif
if (rc_decode == NULL || rc_keys == NULL || rc_keys_size == NULL) {
err("af9005_rc_decode function not found, disabling remote");
af9005_properties.rc.legacy.rc_query = NULL;
{
struct list_head *p, *n;
- usb_put_intf(dev->intf);
- usb_put_dev(dev->udev);
-
uvc_status_cleanup(dev);
uvc_ctrl_cleanup_device(dev);
+ usb_put_intf(dev->intf);
+ usb_put_dev(dev->udev);
+
if (dev->vdev.dev)
v4l2_device_unregister(&dev->vdev);
#ifdef CONFIG_MEDIA_CONTROLLER
sdhci_runtime_pm_get(host);
+ present = mmc_gpio_get_cd(host->mmc);
+
spin_lock_irqsave(&host->lock, flags);
WARN_ON(host->mrq != NULL);
* zero: cd-gpio is used, and card is removed
* one: cd-gpio is used, and card is present
*/
- present = mmc_gpio_get_cd(host->mmc);
if (present < 0) {
/* If polling, assume that the card is always present. */
if (host->quirks & SDHCI_QUIRK_BROKEN_CARD_DETECTION)
if (err)
netdev_warn(netdev, "Cannot stop device, error %d\n", err);
+ /* reset tx contexts */
+ kvaser_usb_unlink_tx_urbs(priv);
+
priv->can.state = CAN_STATE_STOPPED;
close_candev(priv->netdev);
if (!urb) {
netdev_err(netdev, "No memory left for URBs\n");
stats->tx_dropped++;
- goto nourbmem;
+ dev_kfree_skb(skb);
+ return NETDEV_TX_OK;
}
buf = kmalloc(sizeof(struct kvaser_msg), GFP_ATOMIC);
if (!buf) {
stats->tx_dropped++;
+ dev_kfree_skb(skb);
goto nobufmem;
}
}
}
+ /* This should never happen; it implies a flow control bug */
if (!context) {
netdev_warn(netdev, "cannot find free context\n");
ret = NETDEV_TX_BUSY;
if (unlikely(err)) {
can_free_echo_skb(netdev, context->echo_index);
- skb = NULL; /* set to NULL to avoid double free in
- * dev_kfree_skb(skb) */
-
atomic_dec(&priv->active_tx_urbs);
usb_unanchor_urb(urb);
kfree(buf);
nobufmem:
usb_free_urb(urb);
-nourbmem:
- dev_kfree_skb(skb);
return ret;
}
struct kvaser_usb_net_priv *priv;
int i, err;
+ err = kvaser_usb_send_simple_msg(dev, CMD_RESET_CHIP, channel);
+ if (err)
+ return err;
+
netdev = alloc_candev(sizeof(*priv), MAX_TX_URBS);
if (!netdev) {
dev_err(&intf->dev, "Cannot alloc candev\n");
usb_set_intfdata(intf, dev);
- for (i = 0; i < MAX_NET_DEVICES; i++)
- kvaser_usb_send_simple_msg(dev, CMD_RESET_CHIP, i);
-
err = kvaser_usb_get_software_info(dev);
if (err) {
dev_err(&intf->dev,
schedule_work(&alx->reset_wk);
}
-static bool alx_clean_rx_irq(struct alx_priv *alx, int budget)
+static int alx_clean_rx_irq(struct alx_priv *alx, int budget)
{
struct alx_rx_queue *rxq = &alx->rxq;
struct alx_rrd *rrd;
struct alx_buffer *rxb;
struct sk_buff *skb;
u16 length, rfd_cleaned = 0;
+ int work = 0;
- while (budget > 0) {
+ while (work < budget) {
rrd = &rxq->rrd[rxq->rrd_read_idx];
if (!(rrd->word3 & cpu_to_le32(1 << RRD_UPDATED_SHIFT)))
break;
ALX_GET_FIELD(le32_to_cpu(rrd->word0),
RRD_NOR) != 1) {
alx_schedule_reset(alx);
- return 0;
+ return work;
}
rxb = &rxq->bufs[rxq->read_idx];
}
napi_gro_receive(&alx->napi, skb);
- budget--;
+ work++;
next_pkt:
if (++rxq->read_idx == alx->rx_ringsz)
if (rfd_cleaned)
alx_refill_rx_ring(alx, GFP_ATOMIC);
- return budget > 0;
+ return work;
}
static int alx_poll(struct napi_struct *napi, int budget)
{
struct alx_priv *alx = container_of(napi, struct alx_priv, napi);
struct alx_hw *hw = &alx->hw;
- bool complete = true;
unsigned long flags;
+ bool tx_complete;
+ int work;
- complete = alx_clean_tx_irq(alx) &&
- alx_clean_rx_irq(alx, budget);
+ tx_complete = alx_clean_tx_irq(alx);
+ work = alx_clean_rx_irq(alx, budget);
- if (!complete)
- return 1;
+ if (!tx_complete || work == budget)
+ return budget;
napi_complete(&alx->napi);
alx_post_write(hw);
- return 0;
+ return work;
}
static irqreturn_t alx_intr_handle(struct alx_priv *alx, u32 intr)
goto err_out_apeunmap;
}
- /*
- * Reset chip in case UNDI or EFI driver did not shutdown
- * DMA self test will enable WDMAC and we'll see (spurious)
- * pending DMA on the PCI bus at that point.
- */
- if ((tr32(HOSTCC_MODE) & HOSTCC_MODE_ENABLE) ||
- (tr32(WDMAC_MODE) & WDMAC_MODE_ENABLE)) {
- tw32(MEMARB_MODE, MEMARB_MODE_ENABLE);
- tg3_halt(tp, RESET_KIND_SHUTDOWN, 1);
- }
-
- err = tg3_test_dma(tp);
- if (err) {
- dev_err(&pdev->dev, "DMA engine test failed, aborting\n");
- goto err_out_apeunmap;
- }
-
intmbx = MAILBOX_INTERRUPT_0 + TG3_64BIT_REG_LOW;
rcvmbx = MAILBOX_RCVRET_CON_IDX_0 + TG3_64BIT_REG_LOW;
sndmbx = MAILBOX_SNDHOST_PROD_IDX_0 + TG3_64BIT_REG_LOW;
sndmbx += 0xc;
}
+ /*
+ * Reset chip in case UNDI or EFI driver did not shutdown
+ * DMA self test will enable WDMAC and we'll see (spurious)
+ * pending DMA on the PCI bus at that point.
+ */
+ if ((tr32(HOSTCC_MODE) & HOSTCC_MODE_ENABLE) ||
+ (tr32(WDMAC_MODE) & WDMAC_MODE_ENABLE)) {
+ tw32(MEMARB_MODE, MEMARB_MODE_ENABLE);
+ tg3_halt(tp, RESET_KIND_SHUTDOWN, 1);
+ }
+
+ err = tg3_test_dma(tp);
+ if (err) {
+ dev_err(&pdev->dev, "DMA engine test failed, aborting\n");
+ goto err_out_apeunmap;
+ }
+
tg3_init_coal(tp);
pci_set_drvdata(pdev, dev);
skb_put(skb, bytes_written);
skb->protocol = eth_type_trans(skb, netdev);
- if ((netdev->features & NETIF_F_RXCSUM) && !csum_not_calc) {
- skb->csum = htons(checksum);
- skb->ip_summed = CHECKSUM_COMPLETE;
- }
+ /* Hardware does not provide whole packet checksum. It only
+ * provides pseudo checksum. Since hw validates the packet
+ * checksum but not provide us the checksum value. use
+ * CHECSUM_UNNECESSARY.
+ */
+ if ((netdev->features & NETIF_F_RXCSUM) && tcp_udp_csum_ok &&
+ ipv4_csum_ok)
+ skb->ip_summed = CHECKSUM_UNNECESSARY;
if (vlan_stripped)
__vlan_hwaccel_put_tag(skb, htons(ETH_P_8021Q), vlan_tci);
AXIS_DMI_MATCH("HPB64xx", "HP ProBook 64", xy_swap),
AXIS_DMI_MATCH("HPB64xx", "HP EliteBook 84", xy_swap),
AXIS_DMI_MATCH("HPB65xx", "HP ProBook 65", x_inverted),
+ AXIS_DMI_MATCH("HPZBook15", "HP ZBook 15", x_inverted),
{ NULL, }
/* Laptop models without axis info (yet):
* "NC6910" "HP Compaq 6910"
unsigned long flags;
spin_lock_irqsave(get_ccwdev_lock(raw->cdev), flags);
- if (raw->flags & RAW3215_TIMER_RUNS) {
- del_timer(&raw->timer);
- raw->flags &= ~RAW3215_TIMER_RUNS;
- if (!(raw->port.flags & ASYNC_SUSPENDED)) {
- raw3215_mk_write_req(raw);
- raw3215_start_io(raw);
+ raw->flags &= ~RAW3215_TIMER_RUNS;
+ if (!(raw->port.flags & ASYNC_SUSPENDED)) {
+ raw3215_mk_write_req(raw);
+ raw3215_start_io(raw);
+ if ((raw->queued_read || raw->queued_write) &&
+ !(raw->flags & RAW3215_WORKING) &&
+ !(raw->flags & RAW3215_TIMER_RUNS)) {
+ raw->timer.expires = RAW3215_TIMEOUT + jiffies;
+ add_timer(&raw->timer);
+ raw->flags |= RAW3215_TIMER_RUNS;
}
}
spin_unlock_irqrestore(get_ccwdev_lock(raw->cdev), flags);
(raw->flags & RAW3215_FLUSHING)) {
/* execute write requests bigger than minimum size */
raw3215_start_io(raw);
- if (raw->flags & RAW3215_TIMER_RUNS) {
- del_timer(&raw->timer);
- raw->flags &= ~RAW3215_TIMER_RUNS;
- }
- } else if (!(raw->flags & RAW3215_TIMER_RUNS)) {
- /* delay small writes */
- raw->timer.expires = RAW3215_TIMEOUT + jiffies;
- add_timer(&raw->timer);
- raw->flags |= RAW3215_TIMER_RUNS;
}
}
+ if ((raw->queued_read || raw->queued_write) &&
+ !(raw->flags & RAW3215_WORKING) &&
+ !(raw->flags & RAW3215_TIMER_RUNS)) {
+ raw->timer.expires = RAW3215_TIMEOUT + jiffies;
+ add_timer(&raw->timer);
+ raw->flags |= RAW3215_TIMER_RUNS;
+ }
}
/*
const unsigned char *buf, int count)
{
struct raw3215_info *raw;
+ int i, written;
if (!tty)
return 0;
raw = (struct raw3215_info *) tty->driver_data;
- raw3215_write(raw, buf, count);
- return count;
+ written = count;
+ while (count > 0) {
+ for (i = 0; i < count; i++)
+ if (buf[i] == '\t' || buf[i] == '\n')
+ break;
+ raw3215_write(raw, buf, i);
+ count -= i;
+ buf += i;
+ if (count > 0) {
+ raw3215_putchar(raw, *buf);
+ count--;
+ buf++;
+ }
+ }
+ return written;
}
/*
driver->subtype = SYSTEM_TYPE_TTY;
driver->init_termios = tty_std_termios;
driver->init_termios.c_iflag = IGNBRK | IGNPAR;
- driver->init_termios.c_oflag = ONLCR | XTABS;
+ driver->init_termios.c_oflag = ONLCR;
driver->init_termios.c_lflag = ISIG;
driver->flags = TTY_DRIVER_REAL_RAW;
tty_set_operations(driver, &tty3215_ops);
if (ret == -EAGAIN) {
/* no more space */
- if (cmd_request->bounce_sgl_count) {
+ if (cmd_request->bounce_sgl_count)
destroy_bounce_buffer(cmd_request->bounce_sgl,
cmd_request->bounce_sgl_count);
- ret = SCSI_MLQUEUE_DEVICE_BUSY;
- goto queue_error;
- }
+ ret = SCSI_MLQUEUE_DEVICE_BUSY;
+ goto queue_error;
}
return 0;
struct iscsi_conn *conn,
struct iscsi_data_count *count)
{
- int data = count->data_length, total_tx = 0, tx_loop = 0, iov_len;
+ int ret, iov_len;
struct kvec *iov_p;
struct msghdr msg;
if (!conn || !conn->sock || !conn->conn_ops)
return -1;
- if (data <= 0) {
- pr_err("Data length is: %d\n", data);
+ if (count->data_length <= 0) {
+ pr_err("Data length is: %d\n", count->data_length);
return -1;
}
iov_p = count->iov;
iov_len = count->iov_count;
- while (total_tx < data) {
- tx_loop = kernel_sendmsg(conn->sock, &msg, iov_p, iov_len,
- (data - total_tx));
- if (tx_loop <= 0) {
- pr_debug("tx_loop: %d total_tx %d\n",
- tx_loop, total_tx);
- return tx_loop;
- }
- total_tx += tx_loop;
- pr_debug("tx_loop: %d, total_tx: %d, data: %d\n",
- tx_loop, total_tx, data);
+ ret = kernel_sendmsg(conn->sock, &msg, iov_p, iov_len,
+ count->data_length);
+ if (ret != count->data_length) {
+ pr_err("Unexpected ret: %d send data %d\n",
+ ret, count->data_length);
+ return -EPIPE;
}
+ pr_debug("ret: %d, sent data: %d\n", ret, count->data_length);
- return total_tx;
+ return ret;
}
int rx_data(
if (i == (request->num_mapped_sgs - 1) ||
sg_is_last(s)) {
- if (list_is_last(&req->list,
- &dep->request_list))
+ if (list_empty(&dep->request_list))
last_one = true;
chain = false;
}
if (last_one)
break;
}
+
+ if (last_one)
+ break;
} else {
dma = req->request.dma;
length = req->request.length;
{
void __iomem *base;
u32 control;
- u32 fminterval;
+ u32 fminterval = 0;
+ bool no_fminterval = false;
int cnt;
if (!mmio_resource_enabled(pdev, 0))
if (base == NULL)
return;
+ /*
+ * ULi M5237 OHCI controller locks the whole system when accessing
+ * the OHCI_FMINTERVAL offset.
+ */
+ if (pdev->vendor == PCI_VENDOR_ID_AL && pdev->device == 0x5237)
+ no_fminterval = true;
+
control = readl(base + OHCI_CONTROL);
/* On PA-RISC, PDC can leave IR set incorrectly; ignore it there. */
}
/* software reset of the controller, preserving HcFmInterval */
- fminterval = readl(base + OHCI_FMINTERVAL);
+ if (!no_fminterval)
+ fminterval = readl(base + OHCI_FMINTERVAL);
+
writel(OHCI_HCR, base + OHCI_CMDSTATUS);
/* reset requires max 10 us delay */
break;
udelay(1);
}
- writel(fminterval, base + OHCI_FMINTERVAL);
+
+ if (!no_fminterval)
+ writel(fminterval, base + OHCI_FMINTERVAL);
/* Now the controller is safely in SUSPEND and nothing can wake it up */
iounmap(base);
{ USB_DEVICE(0x10C4, 0x85F8) }, /* Virtenio Preon32 */
{ USB_DEVICE(0x10C4, 0x8664) }, /* AC-Services CAN-IF */
{ USB_DEVICE(0x10C4, 0x8665) }, /* AC-Services OBD-IF */
- { USB_DEVICE(0x10C4, 0x8875) }, /* CEL MeshConnect USB Stick */
+ { USB_DEVICE(0x10C4, 0x8856) }, /* CEL EM357 ZigBee USB Stick - LR */
+ { USB_DEVICE(0x10C4, 0x8857) }, /* CEL EM357 ZigBee USB Stick */
{ USB_DEVICE(0x10C4, 0x88A4) }, /* MMB Networks ZigBee USB Device */
{ USB_DEVICE(0x10C4, 0x88A5) }, /* Planet Innovation Ingeni ZigBee USB Device */
{ USB_DEVICE(0x10C4, 0x8946) }, /* Ketra N1 Wireless Interface */
+ { USB_DEVICE(0x10C4, 0x8977) }, /* CEL MeshWorks DevKit Device */
{ USB_DEVICE(0x10C4, 0xEA60) }, /* Silicon Labs factory default */
{ USB_DEVICE(0x10C4, 0xEA61) }, /* Silicon Labs factory default */
{ USB_DEVICE(0x10C4, 0xEA70) }, /* Silicon Labs factory default */
}
port = serial->port[msg->port];
p_priv = usb_get_serial_port_data(port);
+ if (!p_priv)
+ goto resubmit;
/* Update handshaking pin state information */
old_dcd_state = p_priv->dcd_state;
if (old_dcd_state != p_priv->dcd_state)
tty_port_tty_hangup(&port->port, true);
-
+resubmit:
/* Resubmit urb so we continue receiving */
err = usb_submit_urb(urb, GFP_ATOMIC);
if (err != 0)
}
port = serial->port[msg->port];
p_priv = usb_get_serial_port_data(port);
+ if (!p_priv)
+ goto resubmit;
/* Update handshaking pin state information */
old_dcd_state = p_priv->dcd_state;
if (old_dcd_state != p_priv->dcd_state && old_dcd_state)
tty_port_tty_hangup(&port->port, true);
-
+resubmit:
/* Resubmit urb so we continue receiving */
err = usb_submit_urb(urb, GFP_ATOMIC);
if (err != 0)
}
port = serial->port[msg->portNumber];
p_priv = usb_get_serial_port_data(port);
+ if (!p_priv)
+ goto resubmit;
/* Update handshaking pin state information */
old_dcd_state = p_priv->dcd_state;
if (old_dcd_state != p_priv->dcd_state && old_dcd_state)
tty_port_tty_hangup(&port->port, true);
-
+resubmit:
/* Resubmit urb so we continue receiving */
err = usb_submit_urb(urb, GFP_ATOMIC);
if (err != 0)
port = serial->port[0];
p_priv = usb_get_serial_port_data(port);
+ if (!p_priv)
+ goto resubmit;
/* Update handshaking pin state information */
old_dcd_state = p_priv->dcd_state;
if (old_dcd_state != p_priv->dcd_state && old_dcd_state)
tty_port_tty_hangup(&port->port, true);
-
+resubmit:
/* Resubmit urb so we continue receiving */
err = usb_submit_urb(urb, GFP_ATOMIC);
if (err != 0)
port = serial->port[msg->port];
p_priv = usb_get_serial_port_data(port);
+ if (!p_priv)
+ goto resubmit;
/* Update handshaking pin state information */
old_dcd_state = p_priv->dcd_state;
if (old_dcd_state != p_priv->dcd_state && old_dcd_state)
tty_port_tty_hangup(&port->port, true);
-
+resubmit:
/* Resubmit urb so we continue receiving */
err = usb_submit_urb(urb, GFP_ATOMIC);
if (err != 0)
static int vfio_pci_probe(struct pci_dev *pdev, const struct pci_device_id *id)
{
- u8 type;
struct vfio_pci_device *vdev;
struct iommu_group *group;
int ret;
- pci_read_config_byte(pdev, PCI_HEADER_TYPE, &type);
- if ((type & PCI_HEADER_TYPE) != PCI_HEADER_TYPE_NORMAL)
+ if (pdev->hdr_type != PCI_HEADER_TYPE_NORMAL)
return -EINVAL;
group = iommu_group_get(&pdev->dev);
module_param(nologo, bool, 0);
MODULE_PARM_DESC(nologo, "Disables startup logo");
+/*
+ * Logos are located in the initdata, and will be freed in kernel_init.
+ * Use late_init to mark the logos as freed to prevent any further use.
+ */
+
+static bool logos_freed;
+
+static int __init fb_logo_late_init(void)
+{
+ logos_freed = true;
+ return 0;
+}
+
+late_initcall(fb_logo_late_init);
+
/* logo's are marked __initdata. Use __init_refok to tell
* modpost that it is intended that this function uses data
* marked __initdata.
{
const struct linux_logo *logo = NULL;
- if (nologo)
+ if (nologo || logos_freed)
return NULL;
if (depth >= 1) {
dprintk("NFS locking service started (ver " LOCKD_VERSION ").\n");
- if (!nlm_timeout)
- nlm_timeout = LOCKD_DFLT_TIMEO;
- nlmsvc_timeout = nlm_timeout * HZ;
-
/*
* The main request loop. We don't terminate until the last
* NFS mount or NFS daemon has gone away.
printk(KERN_WARNING
"lockd_up: no pid, %d users??\n", nlmsvc_users);
+ if (!nlm_timeout)
+ nlm_timeout = LOCKD_DFLT_TIMEO;
+ nlmsvc_timeout = nlm_timeout * HZ;
+
serv = svc_create(&nlmsvc_program, LOCKD_BUFSIZE, NULL);
if (!serv) {
printk(KERN_WARNING "lockd_up: create service failed\n");
}
/*
- * Returns true if the server owners match
+ * Returns true if the server major ids match
*/
static bool
-nfs4_match_serverowners(struct nfs_client *a, struct nfs_client *b)
+nfs4_check_clientid_trunking(struct nfs_client *a, struct nfs_client *b)
{
struct nfs41_server_owner *o1 = a->cl_serverowner;
struct nfs41_server_owner *o2 = b->cl_serverowner;
- if (o1->minor_id != o2->minor_id) {
- dprintk("NFS: --> %s server owner minor IDs do not match\n",
- __func__);
- return false;
- }
-
if (o1->major_id_sz != o2->major_id_sz)
goto out_major_mismatch;
if (memcmp(o1->major_id, o2->major_id, o1->major_id_sz) != 0)
if (!nfs4_match_clientids(pos, new))
continue;
- if (!nfs4_match_serverowners(pos, new))
+ /*
+ * Note that session trunking is just a special subcase of
+ * client id trunking. In either case, we want to fall back
+ * to using the existing nfs_client.
+ */
+ if (!nfs4_check_clientid_trunking(pos, new))
continue;
atomic_inc(&pos->cl_count);
spin_unlock(&inode->i_lock);
/* In case the dropping of a reference would nuke next_i. */
- if ((&next_i->i_sb_list != list) &&
- atomic_read(&next_i->i_count)) {
+ while (&next_i->i_sb_list != list) {
spin_lock(&next_i->i_lock);
- if (!(next_i->i_state & (I_FREEING | I_WILL_FREE))) {
+ if (!(next_i->i_state & (I_FREEING | I_WILL_FREE)) &&
+ atomic_read(&next_i->i_count)) {
__iget(next_i);
need_iput = next_i;
+ spin_unlock(&next_i->i_lock);
+ break;
}
spin_unlock(&next_i->i_lock);
+ next_i = list_entry(next_i->i_sb_list.next,
+ struct inode, i_sb_list);
}
/*
- * We can safely drop inode_sb_list_lock here because we hold
- * references on both inode and next_i. Also no new inodes
- * will be added since the umount has begun.
+ * We can safely drop inode_sb_list_lock here because either
+ * we actually hold references on both inode and next_i or
+ * end of list. Also no new inodes will be added since the
+ * umount has begun.
*/
spin_unlock(&inode_sb_list_lock);
if (get_bits(bd, 1))
return RETVAL_OBSOLETE_INPUT;
origPtr = get_bits(bd, 24);
- if (origPtr > dbufSize)
+ if (origPtr >= dbufSize)
return RETVAL_DATA_ERROR;
/* mapping table: if some byte values are never used (encoding things
like ascii text), the compression code removes the gaps to have fewer
if (unlikely(!tcp_snd_wnd_test(tp, skb, mss_now)))
break;
- if (tso_segs == 1) {
+ if (tso_segs == 1 || !sk->sk_gso_max_segs) {
if (unlikely(!tcp_nagle_test(tp, skb, mss_now,
(tcp_skb_is_last(sk, skb) ?
nonagle : TCP_NAGLE_PUSH))))
}
limit = mss_now;
- if (tso_segs > 1 && !tcp_urg_mode(tp))
+ if (tso_segs > 1 && sk->sk_gso_max_segs && !tcp_urg_mode(tp))
limit = tcp_mss_split_point(sk, skb, mss_now,
min_t(unsigned int,
cwnd_quota,
if (*op < IP_SET_OP_VERSION) {
/* Check the version at the beginning of operations */
struct ip_set_req_version *req_version = data;
+
+ if (*len < sizeof(struct ip_set_req_version)) {
+ ret = -EINVAL;
+ goto done;
+ }
+
if (req_version->version != IPSET_PROTOCOL) {
ret = -EPROTO;
goto done;
return err;
}
-static void netlink_frame_flush_dcache(const struct nl_mmap_hdr *hdr)
+static void netlink_frame_flush_dcache(const struct nl_mmap_hdr *hdr, unsigned int nm_len)
{
#if ARCH_IMPLEMENTS_FLUSH_DCACHE_PAGE == 1
struct page *p_start, *p_end;
/* First page is flushed through netlink_{get,set}_status */
p_start = pgvec_to_page(hdr + PAGE_SIZE);
- p_end = pgvec_to_page((void *)hdr + NL_MMAP_HDRLEN + hdr->nm_len - 1);
+ p_end = pgvec_to_page((void *)hdr + NL_MMAP_HDRLEN + nm_len - 1);
while (p_start <= p_end) {
flush_dcache_page(p_start);
p_start++;
static void netlink_set_status(struct nl_mmap_hdr *hdr,
enum nl_mmap_status status)
{
+ smp_mb();
hdr->nm_status = status;
flush_dcache_page(pgvec_to_page(hdr));
- smp_wmb();
}
static struct nl_mmap_hdr *
struct nl_mmap_hdr *hdr;
struct sk_buff *skb;
unsigned int maxlen;
- bool excl = true;
int err = 0, len = 0;
- /* Netlink messages are validated by the receiver before processing.
- * In order to avoid userspace changing the contents of the message
- * after validation, the socket and the ring may only be used by a
- * single process, otherwise we fall back to copying.
- */
- if (atomic_long_read(&sk->sk_socket->file->f_count) > 1 ||
- atomic_read(&nlk->mapped) > 1)
- excl = false;
-
mutex_lock(&nlk->pg_vec_lock);
ring = &nlk->tx_ring;
maxlen = ring->frame_size - NL_MMAP_HDRLEN;
do {
+ unsigned int nm_len;
+
hdr = netlink_current_frame(ring, NL_MMAP_STATUS_VALID);
if (hdr == NULL) {
if (!(msg->msg_flags & MSG_DONTWAIT) &&
schedule();
continue;
}
- if (hdr->nm_len > maxlen) {
+
+ nm_len = ACCESS_ONCE(hdr->nm_len);
+ if (nm_len > maxlen) {
err = -EINVAL;
goto out;
}
- netlink_frame_flush_dcache(hdr);
+ netlink_frame_flush_dcache(hdr, nm_len);
- if (likely(dst_portid == 0 && dst_group == 0 && excl)) {
- skb = alloc_skb_head(GFP_KERNEL);
- if (skb == NULL) {
- err = -ENOBUFS;
- goto out;
- }
- sock_hold(sk);
- netlink_ring_setup_skb(skb, sk, ring, hdr);
- NETLINK_CB(skb).flags |= NETLINK_SKB_TX;
- __skb_put(skb, hdr->nm_len);
- netlink_set_status(hdr, NL_MMAP_STATUS_RESERVED);
- atomic_inc(&ring->pending);
- } else {
- skb = alloc_skb(hdr->nm_len, GFP_KERNEL);
- if (skb == NULL) {
- err = -ENOBUFS;
- goto out;
- }
- __skb_put(skb, hdr->nm_len);
- memcpy(skb->data, (void *)hdr + NL_MMAP_HDRLEN, hdr->nm_len);
- netlink_set_status(hdr, NL_MMAP_STATUS_UNUSED);
+ skb = alloc_skb(nm_len, GFP_KERNEL);
+ if (skb == NULL) {
+ err = -ENOBUFS;
+ goto out;
}
+ __skb_put(skb, nm_len);
+ memcpy(skb->data, (void *)hdr + NL_MMAP_HDRLEN, nm_len);
+ netlink_set_status(hdr, NL_MMAP_STATUS_UNUSED);
netlink_increment_head(ring);
hdr->nm_pid = NETLINK_CB(skb).creds.pid;
hdr->nm_uid = from_kuid(sk_user_ns(sk), NETLINK_CB(skb).creds.uid);
hdr->nm_gid = from_kgid(sk_user_ns(sk), NETLINK_CB(skb).creds.gid);
- netlink_frame_flush_dcache(hdr);
+ netlink_frame_flush_dcache(hdr, hdr->nm_len);
netlink_set_status(hdr, NL_MMAP_STATUS_VALID);
NETLINK_CB(skb).flags |= NETLINK_SKB_DELIVERED;
{
struct ieee80211_sta_ht_cap *ht_cap;
struct ieee80211_sta_vht_cap *vht_cap;
- u32 width, control_freq;
+ u32 width, control_freq, cap;
if (WARN_ON(!cfg80211_chandef_valid(chandef)))
return false;
return false;
break;
case NL80211_CHAN_WIDTH_80P80:
- if (!(vht_cap->cap & IEEE80211_VHT_CAP_SUPP_CHAN_WIDTH_160_80PLUS80MHZ))
+ cap = vht_cap->cap & IEEE80211_VHT_CAP_SUPP_CHAN_WIDTH_MASK;
+ if (cap != IEEE80211_VHT_CAP_SUPP_CHAN_WIDTH_160_80PLUS80MHZ)
return false;
case NL80211_CHAN_WIDTH_80:
if (!vht_cap->vht_supported)
case NL80211_CHAN_WIDTH_160:
if (!vht_cap->vht_supported)
return false;
- if (!(vht_cap->cap & IEEE80211_VHT_CAP_SUPP_CHAN_WIDTH_160MHZ))
+ cap = vht_cap->cap & IEEE80211_VHT_CAP_SUPP_CHAN_WIDTH_MASK;
+ if (cap != IEEE80211_VHT_CAP_SUPP_CHAN_WIDTH_160MHZ &&
+ cap != IEEE80211_VHT_CAP_SUPP_CHAN_WIDTH_160_80PLUS80MHZ)
return false;
prohibited_flags |= IEEE80211_CHAN_NO_160MHZ;
width = 160;
projects / GitHub / mt8127 / android_kernel_alcatel_ttab.git / commitdiff