sound/oss/Kconfig

   1 # 18 Apr 1998, Michael Elizabeth Chastain, <mailto:mec@shout.net>
   2 # More hacking for modularisation.
   3 #
   4 # Prompt user for primary drivers.
   5
   6 config SOUND_BCM_CS4297A
   7         tristate "Crystal Sound CS4297a (for Swarm)"
   8         depends on SIBYTE_SWARM
   9         help
  10           The BCM91250A has a Crystal CS4297a on synchronous serial
  11           port B (in addition to the DB-9 serial port).  Say Y or M
  12           here to enable the sound chip instead of the UART.  Also
  13           note that CONFIG_KGDB should not be enabled at the same
  14           time, since it also attempts to use this UART port.
  15
  16 config SOUND_VWSND
  17         tristate "SGI Visual Workstation Sound"
  18         depends on X86_VISWS
  19         help
  20           Say Y or M if you have an SGI Visual Workstation and you want to be
  21           able to use its on-board audio.  Read
  22           <file:Documentation/sound/oss/vwsnd> for more info on this driver's
  23           capabilities.
  24
  25 config SOUND_MSNDCLAS
  26         tristate "Support for Turtle Beach MultiSound Classic, Tahiti, Monterey"
  27         depends on (m || !STANDALONE) && ISA
  28         help
  29           Say M here if you have a Turtle Beach MultiSound Classic, Tahiti or
  30           Monterey (not for the Pinnacle or Fiji).
  31
  32           See <file:Documentation/sound/oss/MultiSound> for important information
  33           about this driver.  Note that it has been discontinued, but the
  34           Voyetra Turtle Beach knowledge base entry for it is still available
  35           at <http://www.turtlebeach.com/site/kb_ftp/790.asp>.
  36
  37 comment "Compiled-in MSND Classic support requires firmware during compilation."
  38         depends on SOUND_PRIME && SOUND_MSNDCLAS=y
  39
  40 config MSNDCLAS_HAVE_BOOT
  41         bool
  42         depends on SOUND_MSNDCLAS=y && !STANDALONE
  43         default y
  44
  45 config MSNDCLAS_INIT_FILE
  46         string "Full pathname of MSNDINIT.BIN firmware file"
  47         depends on SOUND_MSNDCLAS
  48         default "/etc/sound/msndinit.bin"
  49         help
  50           The MultiSound cards have two firmware files which are required for
  51           operation, and are not currently included. These files can be
  52           obtained from Turtle Beach. See
  53           <file:Documentation/sound/oss/MultiSound> for information on how to
  54           obtain this.
  55
  56 config MSNDCLAS_PERM_FILE
  57         string "Full pathname of MSNDPERM.BIN firmware file"
  58         depends on SOUND_MSNDCLAS
  59         default "/etc/sound/msndperm.bin"
  60         help
  61           The MultiSound cards have two firmware files which are required for
  62           operation, and are not currently included. These files can be
  63           obtained from Turtle Beach. See
  64           <file:Documentation/sound/oss/MultiSound> for information on how to
  65           obtain this.
  66
  67 config MSNDCLAS_IRQ
  68         int "MSND Classic IRQ 5, 7, 9, 10, 11, 12"
  69         depends on SOUND_MSNDCLAS=y
  70         default "5"
  71         help
  72           Interrupt Request line for the MultiSound Classic and related cards.
  73
  74 config MSNDCLAS_MEM
  75         hex "MSND Classic memory B0000, C8000, D0000, D8000, E0000, E8000"
  76         depends on SOUND_MSNDCLAS=y
  77         default "D0000"
  78         help
  79           Memory-mapped I/O base address for the MultiSound Classic and
  80           related cards.
  81
  82 config MSNDCLAS_IO
  83         hex "MSND Classic I/O 210, 220, 230, 240, 250, 260, 290, 3E0"
  84         depends on SOUND_MSNDCLAS=y
  85         default "290"
  86         help
  87           I/O port address for the MultiSound Classic and related cards.
  88
  89 config SOUND_MSNDPIN
  90         tristate "Support for Turtle Beach MultiSound Pinnacle, Fiji"
  91         depends on (m || !STANDALONE) && ISA
  92         help
  93           Say M here if you have a Turtle Beach MultiSound Pinnacle or Fiji.
  94           See <file:Documentation/sound/oss/MultiSound> for important information
  95           about this driver. Note that it has been discontinued, but the
  96           Voyetra Turtle Beach knowledge base entry for it is still available
  97           at <http://www.turtlebeach.com/site/kb_ftp/600.asp>.
  98
  99 comment "Compiled-in MSND Pinnacle support requires firmware during compilation."
 100         depends on SOUND_PRIME && SOUND_MSNDPIN=y
 101
 102 config MSNDPIN_HAVE_BOOT
 103         bool
 104         depends on SOUND_MSNDPIN=y
 105         default y
 106
 107 config MSNDPIN_INIT_FILE
 108         string "Full pathname of PNDSPINI.BIN firmware file"
 109         depends on SOUND_MSNDPIN
 110         default "/etc/sound/pndspini.bin"
 111         help
 112           The MultiSound cards have two firmware files which are required
 113           for operation, and are not currently included. These files can be
 114           obtained from Turtle Beach. See
 115           <file:Documentation/sound/oss/MultiSound> for information on how to
 116           obtain this.
 117
 118 config MSNDPIN_PERM_FILE
 119         string "Full pathname of PNDSPERM.BIN firmware file"
 120         depends on SOUND_MSNDPIN
 121         default "/etc/sound/pndsperm.bin"
 122         help
 123           The MultiSound cards have two firmware files which are required for
 124           operation, and are not currently included. These files can be
 125           obtained from Turtle Beach. See
 126           <file:Documentation/sound/oss/MultiSound> for information on how to
 127           obtain this.
 128
 129 config MSNDPIN_IRQ
 130         int "MSND Pinnacle IRQ 5, 7, 9, 10, 11, 12"
 131         depends on SOUND_MSNDPIN=y
 132         default "5"
 133         help
 134           Interrupt request line for the primary synthesizer on MultiSound
 135           Pinnacle and Fiji sound cards.
 136
 137 config MSNDPIN_MEM
 138         hex "MSND Pinnacle memory B0000, C8000, D0000, D8000, E0000, E8000"
 139         depends on SOUND_MSNDPIN=y
 140         default "D0000"
 141         help
 142           Memory-mapped I/O base address for the primary synthesizer on
 143           MultiSound Pinnacle and Fiji sound cards.
 144
 145 config MSNDPIN_IO
 146         hex "MSND Pinnacle I/O 210, 220, 230, 240, 250, 260, 290, 3E0"
 147         depends on SOUND_MSNDPIN=y
 148         default "290"
 149         help
 150           Memory-mapped I/O base address for the primary synthesizer on
 151           MultiSound Pinnacle and Fiji sound cards.
 152
 153 config MSNDPIN_DIGITAL
 154         bool "MSND Pinnacle has S/PDIF I/O"
 155         depends on SOUND_MSNDPIN=y
 156         help
 157           If you have the S/PDIF daughter board for the Pinnacle or Fiji,
 158           answer Y here; otherwise, say N. If you have this, you will be able
 159           to play and record from the S/PDIF port (digital signal). See
 160           <file:Documentation/sound/oss/MultiSound> for information on how to make
 161           use of this capability.
 162
 163 config MSNDPIN_NONPNP
 164         bool "MSND Pinnacle non-PnP Mode"
 165         depends on SOUND_MSNDPIN=y
 166         help
 167           The Pinnacle and Fiji card resources can be configured either with
 168           PnP, or through a configuration port. Say Y here if your card is NOT
 169           in PnP mode. For the Pinnacle, configuration in non-PnP mode allows
 170           use of the IDE and joystick peripherals on the card as well; these
 171           do not show up when the card is in PnP mode. Specifying zero for any
 172           resource of a device will disable the device. If you are running the
 173           card in PnP mode, you must say N here and use isapnptools to
 174           configure the card's resources.
 175
 176 comment "MSND Pinnacle DSP section will be configured to above parameters."
 177         depends on SOUND_MSNDPIN=y && MSNDPIN_NONPNP
 178
 179 config MSNDPIN_CFG
 180         hex "MSND Pinnacle config port 250,260,270"
 181         depends on MSNDPIN_NONPNP
 182         default "250"
 183         help
 184           This is the port which the Pinnacle and Fiji uses to configure the
 185           card's resources when not in PnP mode. If your card is in PnP mode,
 186           then be sure to say N to the previous option, "MSND Pinnacle Non-PnP
 187           Mode".
 188
 189 comment "Pinnacle-specific Device Configuration (0 disables)"
 190         depends on SOUND_MSNDPIN=y && MSNDPIN_NONPNP
 191
 192 config MSNDPIN_MPU_IO
 193         hex "MSND Pinnacle MPU I/O (e.g. 330)"
 194         depends on MSNDPIN_NONPNP
 195         default "0"
 196         help
 197           Memory-mapped I/O base address for the Kurzweil daughterboard
 198           synthesizer on MultiSound Pinnacle and Fiji sound cards.
 199
 200 config MSNDPIN_MPU_IRQ
 201         int "MSND Pinnacle MPU IRQ (e.g. 9)"
 202         depends on MSNDPIN_NONPNP
 203         default "0"
 204         help
 205           Interrupt request number for the Kurzweil daughterboard
 206           synthesizer on MultiSound Pinnacle and Fiji sound cards.
 207
 208 config MSNDPIN_IDE_IO0
 209         hex "MSND Pinnacle IDE I/O 0 (e.g. 170)"
 210         depends on MSNDPIN_NONPNP
 211         default "0"
 212         help
 213           CD-ROM drive 0 memory-mapped I/O base address for the MultiSound
 214           Pinnacle and Fiji sound cards.
 215
 216 config MSNDPIN_IDE_IO1
 217         hex "MSND Pinnacle IDE I/O 1 (e.g. 376)"
 218         depends on MSNDPIN_NONPNP
 219         default "0"
 220         help
 221           CD-ROM drive 1 memory-mapped I/O base address for the MultiSound
 222           Pinnacle and Fiji sound cards.
 223
 224 config MSNDPIN_IDE_IRQ
 225         int "MSND Pinnacle IDE IRQ (e.g. 15)"
 226         depends on MSNDPIN_NONPNP
 227         default "0"
 228         help
 229           Interrupt request number for the IDE CD-ROM interface on the
 230           MultiSound Pinnacle and Fiji sound cards.
 231
 232 config MSNDPIN_JOYSTICK_IO
 233         hex "MSND Pinnacle joystick I/O (e.g. 200)"
 234         depends on MSNDPIN_NONPNP
 235         default "0"
 236         help
 237           Memory-mapped I/O base address for the joystick port on MultiSound
 238           Pinnacle and Fiji sound cards.
 239
 240 config MSND_FIFOSIZE
 241         int "MSND buffer size (kB)"
 242         depends on SOUND_MSNDPIN=y || SOUND_MSNDCLAS=y
 243         default "128"
 244         help
 245           Configures the size of each audio buffer, in kilobytes, for
 246           recording and playing in the MultiSound drivers (both the Classic
 247           and Pinnacle). Larger values reduce the chance of data overruns at
 248           the expense of overall latency. If unsure, use the default.
 249
 250 menuconfig SOUND_OSS
 251         tristate "OSS sound modules"
 252         depends on ISA_DMA_API && VIRT_TO_BUS
 253         depends on !GENERIC_ISA_DMA_SUPPORT_BROKEN
 254         help
 255           OSS is the Open Sound System suite of sound card drivers.  They make
 256           sound programming easier since they provide a common API.  Say Y or
 257           M here (the module will be called sound) if you haven't found a
 258           driver for your sound card above, then pick your driver from the
 259           list below.
 260
 261 if SOUND_OSS
 262
 263 config SOUND_TRACEINIT
 264         bool "Verbose initialisation"
 265         help
 266           Verbose soundcard initialization -- affects the format of autoprobe
 267           and initialization messages at boot time.
 268
 269 config SOUND_DMAP
 270         bool "Persistent DMA buffers"
 271         ---help---
 272           Linux can often have problems allocating DMA buffers for ISA sound
 273           cards on machines with more than 16MB of RAM. This is because ISA
 274           DMA buffers must exist below the 16MB boundary and it is quite
 275           possible that a large enough free block in this region cannot be
 276           found after the machine has been running for a while. If you say Y
 277           here the DMA buffers (64Kb) will be allocated at boot time and kept
 278           until the shutdown. This option is only useful if you said Y to
 279           "OSS sound modules", above. If you said M to "OSS sound modules"
 280           then you can get the persistent DMA buffer functionality by passing
 281           the command-line argument "dmabuf=1" to the sound module.
 282
 283           Say Y unless you have 16MB or more RAM or a PCI sound card.
 284
 285 config SOUND_VMIDI
 286         tristate "Loopback MIDI device support"
 287         help
 288           Support for MIDI loopback on port 1 or 2.
 289
 290 config SOUND_TRIX
 291         tristate "MediaTrix AudioTrix Pro support"
 292         help
 293           Answer Y if you have the AudioTriX Pro sound card manufactured
 294           by MediaTrix.
 295
 296 config TRIX_HAVE_BOOT
 297         bool "Have TRXPRO.HEX firmware file"
 298         depends on SOUND_TRIX=y && !STANDALONE
 299         help
 300           The MediaTrix AudioTrix Pro has an on-board microcontroller which
 301           needs to be initialized by downloading the code from the file
 302           TRXPRO.HEX in the DOS driver directory. If you don't have the
 303           TRXPRO.HEX file handy you may skip this step. However, the SB and
 304           MPU-401 modes of AudioTrix Pro will not work without this file!
 305
 306 config TRIX_BOOT_FILE
 307         string "Full pathname of TRXPRO.HEX firmware file"
 308         depends on TRIX_HAVE_BOOT
 309         default "/etc/sound/trxpro.hex"
 310         help
 311           Enter the full pathname of your TRXPRO.HEX file, starting from /.
 312
 313 config SOUND_MSS
 314         tristate "Microsoft Sound System support"
 315         ---help---
 316           Again think carefully before answering Y to this question.  It's
 317           safe to answer Y if you have the original Windows Sound System card
 318           made by Microsoft or Aztech SG 16 Pro (or NX16 Pro).  Also you may
 319           say Y in case your card is NOT among these:
 320
 321           ATI Stereo F/X, AdLib, Audio Excell DSP16, Cardinal DSP16,
 322           Ensoniq SoundScape (and compatibles made by Reveal and Spea),
 323           Gravis Ultrasound, Gravis Ultrasound ACE, Gravis Ultrasound Max,
 324           Gravis Ultrasound with 16 bit option, Logitech Sound Man 16,
 325           Logitech SoundMan Games, Logitech SoundMan Wave, MAD16 Pro (OPTi
 326           82C929), Media Vision Jazz16, MediaTriX AudioTriX Pro, Microsoft
 327           Windows Sound System (MSS/WSS), Mozart (OAK OTI-601), Orchid
 328           SW32, Personal Sound System (PSS), Pro Audio Spectrum 16, Pro
 329           Audio Studio 16, Pro Sonic 16, Roland MPU-401 MIDI interface,
 330           Sound Blaster 1.0, Sound Blaster 16, Sound Blaster 16ASP, Sound
 331           Blaster 2.0, Sound Blaster AWE32, Sound Blaster Pro, TI TM4000M
 332           notebook, ThunderBoard, Turtle Beach Tropez, Yamaha FM
 333           synthesizers (OPL2, OPL3 and OPL4), 6850 UART MIDI Interface.
 334
 335           For cards having native support in VoxWare, consult the card
 336           specific instructions in <file:Documentation/sound/oss/README.OSS>.
 337           Some drivers have their own MSS support and saying Y to this option
 338           will cause a conflict.
 339
 340           If you compile the driver into the kernel, you have to add
 341           "ad1848=<io>,<irq>,<dma>,<dma2>[,<type>]" to the kernel command
 342           line.
 343
 344 config SOUND_MPU401
 345         tristate "MPU-401 support (NOT for SB16)"
 346         ---help---
 347           Be careful with this question.  The MPU401 interface is supported by
 348           all sound cards.  However, some natively supported cards have their
 349           own driver for MPU401.  Enabling this MPU401 option with these cards
 350           will cause a conflict.  Also, enabling MPU401 on a system that
 351           doesn't really have a MPU401 could cause some trouble.  If your card
 352           was in the list of supported cards, look at the card specific
 353           instructions in the <file:Documentation/sound/oss/README.OSS> file.  It
 354           is safe to answer Y if you have a true MPU401 MIDI interface card.
 355
 356           If you compile the driver into the kernel, you have to add
 357           "mpu401=<io>,<irq>" to the kernel command line.
 358
 359 config SOUND_PAS
 360         tristate "ProAudioSpectrum 16 support"
 361         ---help---
 362           Answer Y only if you have a Pro Audio Spectrum 16, ProAudio Studio
 363           16 or Logitech SoundMan 16 sound card. Answer N if you have some
 364           other card made by Media Vision or Logitech since those are not
 365           PAS16 compatible. Please read <file:Documentation/sound/oss/PAS16>.
 366           It is not necessary to add Sound Blaster support separately; it
 367           is included in PAS support.
 368
 369           If you compile the driver into the kernel, you have to add
 370           "pas2=<io>,<irq>,<dma>,<dma2>,<sbio>,<sbirq>,<sbdma>,<sbdma2>
 371           to the kernel command line.
 372
 373 config PAS_JOYSTICK
 374         bool "Enable PAS16 joystick port"
 375         depends on SOUND_PAS=y
 376         help
 377           Say Y here to enable the Pro Audio Spectrum 16's auxiliary joystick
 378           port.
 379
 380 config SOUND_PSS
 381         tristate "PSS (AD1848, ADSP-2115, ESC614) support"
 382         help
 383           Answer Y or M if you have an Orchid SW32, Cardinal DSP16, Beethoven
 384           ADSP-16 or some other card based on the PSS chipset (AD1848 codec +
 385           ADSP-2115 DSP chip + Echo ESC614 ASIC CHIP). For more information on
 386           how to compile it into the kernel or as a module see the file
 387           <file:Documentation/sound/oss/PSS>.
 388
 389           If you compile the driver into the kernel, you have to add
 390           "pss=<io>,<mssio>,<mssirq>,<mssdma>,<mpuio>,<mpuirq>" to the kernel
 391           command line.
 392
 393 config PSS_MIXER
 394         bool "Enable PSS mixer (Beethoven ADSP-16 and other compatible)"
 395         depends on SOUND_PSS
 396         help
 397           Answer Y for Beethoven ADSP-16. You may try to say Y also for other
 398           cards if they have master volume, bass, treble, and you can't
 399           control it under Linux. If you answer N for Beethoven ADSP-16, you
 400           can't control master volume, bass, treble and synth volume.
 401
 402           If you said M to "PSS support" above, you may enable or disable this
 403           PSS mixer with the module parameter pss_mixer. For more information
 404           see the file <file:Documentation/sound/oss/PSS>.
 405
 406 config PSS_HAVE_BOOT
 407         bool "Have DSPxxx.LD firmware file"
 408         depends on SOUND_PSS && !STANDALONE
 409         help
 410           If you have the DSPxxx.LD file or SYNTH.LD file for you card, say Y
 411           to include this file. Without this file the synth device (OPL) may
 412           not work.
 413
 414 config PSS_BOOT_FILE
 415         string "Full pathname of DSPxxx.LD firmware file"
 416         depends on PSS_HAVE_BOOT
 417         default "/etc/sound/dsp001.ld"
 418         help
 419           Enter the full pathname of your DSPxxx.LD file or SYNTH.LD file,
 420           starting from /.
 421
 422 config SOUND_SB
 423         tristate "100% Sound Blaster compatibles (SB16/32/64, ESS, Jazz16) support"
 424         ---help---
 425           Answer Y if you have an original Sound Blaster card made by Creative
 426           Labs or a 100% hardware compatible clone (like the Thunderboard or
 427           SM Games). For an unknown card you may answer Y if the card claims
 428           to be Sound Blaster-compatible.
 429
 430           Please read the file <file:Documentation/sound/oss/Soundblaster>.
 431
 432           You should also say Y here for cards based on the Avance Logic
 433           ALS-007 and ALS-1X0 chips (read <file:Documentation/sound/oss/ALS>) and
 434           for cards based on ESS chips (read
 435           <file:Documentation/sound/oss/ESS1868> and
 436           <file:Documentation/sound/oss/ESS>). If you have an IBM Mwave
 437           card, say Y here and read <file:Documentation/sound/oss/mwave>.
 438
 439           If you compile the driver into the kernel and don't want to use
 440           isapnp, you have to add "sb=<io>,<irq>,<dma>,<dma2>" to the kernel
 441           command line.
 442
 443           You can say M here to compile this driver as a module; the module is
 444           called sb.
 445
 446 config SOUND_YM3812
 447         tristate "Yamaha FM synthesizer (YM3812/OPL-3) support"
 448         ---help---
 449           Answer Y if your card has a FM chip made by Yamaha (OPL2/OPL3/OPL4).
 450           Answering Y is usually a safe and recommended choice, however some
 451           cards may have software (TSR) FM emulation. Enabling FM support with
 452           these cards may cause trouble (I don't currently know of any such
 453           cards, however). Please read the file
 454           <file:Documentation/sound/oss/OPL3> if your card has an OPL3 chip.
 455
 456           If you compile the driver into the kernel, you have to add
 457           "opl3=<io>" to the kernel command line.
 458
 459           If unsure, say Y.
 460
 461 config SOUND_UART6850
 462         tristate "6850 UART support"
 463         help
 464           This option enables support for MIDI interfaces based on the 6850
 465           UART chip. This interface is rarely found on sound cards. It's safe
 466           to answer N to this question.
 467
 468           If you compile the driver into the kernel, you have to add
 469           "uart6850=<io>,<irq>" to the kernel command line.
 470
 471 config SOUND_AEDSP16
 472         tristate "Gallant Audio Cards (SC-6000 and SC-6600 based)"
 473         ---help---
 474           Answer Y if you have a Gallant's Audio Excel DSP 16 card. This
 475           driver supports Audio Excel DSP 16 but not the III nor PnP versions
 476           of this card.
 477
 478           The Gallant's Audio Excel DSP 16 card can emulate either an SBPro or
 479           a Microsoft Sound System card, so you should have said Y to either
 480           "100% Sound Blaster compatibles (SB16/32/64, ESS, Jazz16) support"
 481           or "Microsoft Sound System support", above, and you need to answer
 482           the "MSS emulation" and "SBPro emulation" questions below
 483           accordingly. You should say Y to one and only one of these two
 484           questions.
 485
 486           Read the <file:Documentation/sound/oss/README.OSS> file and the head of
 487           <file:sound/oss/aedsp16.c> as well as
 488           <file:Documentation/sound/oss/AudioExcelDSP16> to get more information
 489           about this driver and its configuration.
 490
 491 config SC6600
 492         bool "SC-6600 based audio cards (new Audio Excel DSP 16)"
 493         depends on SOUND_AEDSP16
 494         help
 495           The SC6600 is the new version of DSP mounted on the Audio Excel DSP
 496           16 cards. Find in the manual the FCC ID of your audio card and
 497           answer Y if you have an SC6600 DSP.
 498
 499 config SC6600_JOY
 500         bool "Activate SC-6600 Joystick Interface"
 501         depends on SC6600
 502         help
 503           Say Y here in order to use the joystick interface of the Audio Excel
 504           DSP 16 card.
 505
 506 config SC6600_CDROM
 507         int "SC-6600 CDROM Interface (4=None, 3=IDE, 1=Panasonic, 0=?Sony?)"
 508         depends on SC6600
 509         default "4"
 510         help
 511           This is used to activate the CD-ROM interface of the Audio Excel
 512           DSP 16 card. Enter: 0 for Sony, 1 for Panasonic, 2 for IDE, 4 for no
 513           CD-ROM present.
 514
 515 config SC6600_CDROMBASE
 516         hex "SC-6600 CDROM Interface I/O Address"
 517         depends on SC6600
 518         default "0"
 519         help
 520           Base I/O port address for the CD-ROM interface of the Audio Excel
 521           DSP 16 card.
 522
 523 config SOUND_VIDC
 524         tristate "VIDC 16-bit sound"
 525         depends on ARM && ARCH_ACORN
 526         help
 527           16-bit support for the VIDC onboard sound hardware found on Acorn
 528           machines.
 529
 530 config SOUND_WAVEARTIST
 531         tristate "Netwinder WaveArtist"
 532         depends on ARM && ARCH_NETWINDER
 533         help
 534           Say Y here to include support for the Rockwell WaveArtist sound
 535           system.  This driver is mainly for the NetWinder.
 536
 537 config SOUND_KAHLUA
 538         tristate "XpressAudio Sound Blaster emulation"
 539         depends on SOUND_SB
 540
 541 endif   # SOUND_OSS
 542