drivers/video/backlight/Kconfig

   1 #
   2 # Backlight & LCD drivers configuration
   3 #
   4
   5 menuconfig BACKLIGHT_LCD_SUPPORT
   6         bool "Backlight & LCD device support"
   7         help
   8           Enable this to be able to choose the drivers for controlling the
   9           backlight and the LCD panel on some platforms, for example on PDAs.
  10
  11 if BACKLIGHT_LCD_SUPPORT
  12
  13 #
  14 # LCD
  15 #
  16 config LCD_CLASS_DEVICE
  17         tristate "Lowlevel LCD controls"
  18         default m
  19         help
  20           This framework adds support for low-level control of LCD.
  21           Some framebuffer devices connect to platform-specific LCD modules
  22           in order to have a platform-specific way to control the flat panel
  23           (contrast and applying power to the LCD (not to the backlight!)).
  24
  25           To have support for your specific LCD panel you will have to
  26           select the proper drivers which depend on this option.
  27
  28 if LCD_CLASS_DEVICE
  29
  30 config LCD_CORGI
  31         tristate "LCD Panel support for SHARP corgi/spitz model"
  32         depends on SPI_MASTER && PXA_SHARPSL
  33         help
  34           Say y here to support the LCD panels usually found on SHARP
  35           corgi (C7x0) and spitz (Cxx00) models.
  36
  37 config LCD_L4F00242T03
  38         tristate "Epson L4F00242T03 LCD"
  39         depends on SPI_MASTER && GENERIC_GPIO
  40         help
  41           SPI driver for Epson L4F00242T03. This provides basic support
  42           for init and powering the LCD up/down through a sysfs interface.
  43
  44 config LCD_LMS283GF05
  45         tristate "Samsung LMS283GF05 LCD"
  46         depends on SPI_MASTER && GENERIC_GPIO
  47         help
  48           SPI driver for Samsung LMS283GF05. This provides basic support
  49           for powering the LCD up/down through a sysfs interface.
  50
  51 config LCD_LTV350QV
  52         tristate "Samsung LTV350QV LCD Panel"
  53         depends on SPI_MASTER
  54         help
  55           If you have a Samsung LTV350QV LCD panel, say y to include a
  56           power control driver for it.  The panel starts up in power
  57           off state, so you need this driver in order to see any
  58           output.
  59
  60           The LTV350QV panel is present on all ATSTK1000 boards.
  61
  62 config LCD_ILI9320
  63         tristate
  64         help
  65           If you have a panel based on the ILI9320 controller chip
  66           then say y to include a power driver for it.
  67
  68 config LCD_TDO24M
  69         tristate "Toppoly TDO24M  and TDO35S LCD Panels support"
  70         depends on SPI_MASTER
  71         help
  72           If you have a Toppoly TDO24M/TDO35S series LCD panel, say y here to
  73           include the support for it.
  74
  75 config LCD_VGG2432A4
  76         tristate "VGG2432A4 LCM device support"
  77         depends on SPI_MASTER
  78         select LCD_ILI9320
  79         help
  80           If you have a VGG2432A4 panel based on the ILI9320 controller chip
  81           then say y to include a power driver for it.
  82
  83 config LCD_PLATFORM
  84         tristate "Platform LCD controls"
  85         help
  86           This driver provides a platform-device registered LCD power
  87           control interface.
  88
  89 config LCD_TOSA
  90         tristate "Sharp SL-6000 LCD Driver"
  91         depends on I2C && SPI && MACH_TOSA
  92         help
  93           If you have an Sharp SL-6000 Zaurus say Y to enable a driver
  94           for its LCD.
  95
  96 config LCD_HP700
  97         tristate "HP Jornada 700 series LCD Driver"
  98         depends on SA1100_JORNADA720_SSP && !PREEMPT
  99         default y
 100         help
 101           If you have an HP Jornada 700 series handheld (710/720/728)
 102           say Y to enable LCD control driver.
 103
 104 config LCD_S6E63M0
 105         tristate "S6E63M0 AMOLED LCD Driver"
 106         depends on SPI && BACKLIGHT_CLASS_DEVICE
 107         default n
 108         help
 109           If you have an S6E63M0 LCD Panel, say Y to enable its
 110           LCD control driver.
 111
 112 config LCD_LD9040
 113         tristate "LD9040 AMOLED LCD Driver"
 114         depends on SPI && BACKLIGHT_CLASS_DEVICE
 115         default n
 116         help
 117           If you have an LD9040 Panel, say Y to enable its
 118           control driver.
 119
 120 config LCD_AMS369FG06
 121         tristate "AMS369FG06 AMOLED LCD Driver"
 122         depends on SPI && BACKLIGHT_CLASS_DEVICE
 123         default n
 124         help
 125           If you have an AMS369FG06 AMOLED Panel, say Y to enable its
 126           LCD control driver.
 127
 128 endif # LCD_CLASS_DEVICE
 129
 130 #
 131 # Backlight
 132 #
 133 config BACKLIGHT_CLASS_DEVICE
 134         tristate "Lowlevel Backlight controls"
 135         default m
 136         help
 137           This framework adds support for low-level control of the LCD
 138           backlight. This includes support for brightness and power.
 139
 140           To have support for your specific LCD panel you will have to
 141           select the proper drivers which depend on this option.
 142
 143 if BACKLIGHT_CLASS_DEVICE
 144
 145 config BACKLIGHT_ATMEL_LCDC
 146         bool "Atmel LCDC Contrast-as-Backlight control"
 147         depends on FB_ATMEL
 148         default y if MACH_SAM9261EK || MACH_SAM9G10EK || MACH_SAM9263EK
 149         help
 150           This provides a backlight control internal to the Atmel LCDC
 151           driver.  If the LCD "contrast control" on your board is wired
 152           so it controls the backlight brightness, select this option to
 153           export this as a PWM-based backlight control.
 154
 155           If in doubt, it's safe to enable this option; it doesn't kick
 156           in unless the board's description says it's wired that way.
 157
 158 config BACKLIGHT_ATMEL_PWM
 159         tristate "Atmel PWM backlight control"
 160         depends on ATMEL_PWM
 161         help
 162           Say Y here if you want to use the PWM peripheral in Atmel AT91 and
 163           AVR32 devices. This driver will need additional platform data to know
 164           which PWM instance to use and how to configure it.
 165
 166           To compile this driver as a module, choose M here: the module will be
 167           called atmel-pwm-bl.
 168
 169 config BACKLIGHT_EP93XX
 170         tristate "Cirrus EP93xx Backlight Driver"
 171         depends on FB_EP93XX
 172         help
 173           If you have a LCD backlight connected to the BRIGHT output of
 174           the EP93xx, say Y here to enable this driver.
 175
 176           To compile this driver as a module, choose M here: the module will
 177           be called ep93xx_bl.
 178
 179 config BACKLIGHT_GENERIC
 180         tristate "Generic (aka Sharp Corgi) Backlight Driver"
 181         default y
 182         help
 183           Say y to enable the generic platform backlight driver previously
 184           known as the Corgi backlight driver. If you have a Sharp Zaurus
 185           SL-C7xx, SL-Cxx00 or SL-6000x say y.
 186
 187 config BACKLIGHT_LM3533
 188         tristate "Backlight Driver for LM3533"
 189         depends on BACKLIGHT_CLASS_DEVICE
 190         depends on MFD_LM3533
 191         help
 192           Say Y to enable the backlight driver for National Semiconductor / TI
 193           LM3533 Lighting Power chips.
 194
 195           The backlights can be controlled directly, through PWM input, or by
 196           the ambient-light-sensor interface. The chip supports 256 brightness
 197           levels.
 198
 199 config BACKLIGHT_LOCOMO
 200         tristate "Sharp LOCOMO LCD/Backlight Driver"
 201         depends on SHARP_LOCOMO
 202         default y
 203         help
 204           If you have a Sharp Zaurus SL-5500 (Collie) or SL-5600 (Poodle) say y to
 205           enable the LCD/backlight driver.
 206
 207 config BACKLIGHT_OMAP1
 208         tristate "OMAP1 PWL-based LCD Backlight"
 209         depends on ARCH_OMAP1
 210         default y
 211         help
 212           This driver controls the LCD backlight level and power for
 213           the PWL module of OMAP1 processors.  Say Y if your board
 214           uses this hardware.
 215
 216 config BACKLIGHT_HP680
 217         tristate "HP Jornada 680 Backlight Driver"
 218         depends on SH_HP6XX
 219         default y
 220         help
 221           If you have a HP Jornada 680, say y to enable the
 222           backlight driver.
 223
 224 config BACKLIGHT_HP700
 225         tristate "HP Jornada 700 series Backlight Driver"
 226         depends on SA1100_JORNADA720_SSP && !PREEMPT
 227         default y
 228         help
 229           If you have an HP Jornada 700 series,
 230           say Y to include backlight control driver.
 231
 232 config BACKLIGHT_PROGEAR
 233         tristate "Frontpath ProGear Backlight Driver"
 234         depends on PCI && X86
 235         help
 236           If you have a Frontpath ProGear say Y to enable the
 237           backlight driver.
 238
 239 config BACKLIGHT_CARILLO_RANCH
 240         tristate "Intel Carillo Ranch Backlight Driver"
 241         depends on LCD_CLASS_DEVICE && PCI && X86 && FB_LE80578
 242         help
 243           If you have a Intel LE80578 (Carillo Ranch) say Y to enable the
 244           backlight driver.
 245
 246 config BACKLIGHT_PWM
 247         tristate "Generic PWM based Backlight Driver"
 248         depends on HAVE_PWM
 249         help
 250           If you have a LCD backlight adjustable by PWM, say Y to enable
 251           this driver.
 252
 253 config BACKLIGHT_DA903X
 254         tristate "Backlight Driver for DA9030/DA9034 using WLED"
 255         depends on PMIC_DA903X
 256         help
 257           If you have a LCD backlight connected to the WLED output of DA9030
 258           or DA9034 WLED output, say Y here to enable this driver.
 259
 260 config BACKLIGHT_DA9052
 261         tristate "Dialog DA9052/DA9053 WLED"
 262         depends on PMIC_DA9052
 263         help
 264           Enable the Backlight Driver for DA9052-BC and DA9053-AA/Bx PMICs.
 265
 266 config BACKLIGHT_MAX8925
 267         tristate "Backlight driver for MAX8925"
 268         depends on MFD_MAX8925
 269         help
 270           If you have a LCD backlight connected to the WLED output of MAX8925
 271           WLED output, say Y here to enable this driver.
 272
 273 config BACKLIGHT_APPLE
 274        tristate "Apple Backlight Driver"
 275        depends on X86 && ACPI
 276        help
 277          If you have an Intel-based Apple say Y to enable a driver for its
 278          backlight.
 279
 280 config BACKLIGHT_TOSA
 281         tristate "Sharp SL-6000 Backlight Driver"
 282         depends on I2C && MACH_TOSA && LCD_TOSA
 283         help
 284           If you have an Sharp SL-6000 Zaurus say Y to enable a driver
 285           for its backlight
 286
 287 config BACKLIGHT_SAHARA
 288         tristate "Tabletkiosk Sahara Touch-iT Backlight Driver"
 289         depends on X86
 290         help
 291           If you have a Tabletkiosk Sahara Touch-iT, say y to enable the
 292           backlight driver.
 293
 294 config BACKLIGHT_WM831X
 295         tristate "WM831x PMIC Backlight Driver"
 296         depends on MFD_WM831X
 297         help
 298           If you have a backlight driven by the ISINK and DCDC of a
 299           WM831x PMIC say y to enable the backlight driver for it.
 300
 301 config BACKLIGHT_ADP5520
 302         tristate "Backlight Driver for ADP5520/ADP5501 using WLED"
 303         depends on PMIC_ADP5520
 304         help
 305           If you have a LCD backlight connected to the BST/BL_SNK output of
 306           ADP5520 or ADP5501, say Y here to enable this driver.
 307
 308           To compile this driver as a module, choose M here: the module will
 309           be called adp5520_bl.
 310
 311 config BACKLIGHT_ADP8860
 312         tristate "Backlight Driver for ADP8860/ADP8861/ADP8863 using WLED"
 313         depends on BACKLIGHT_CLASS_DEVICE && I2C
 314         select NEW_LEDS
 315         select LEDS_CLASS
 316         help
 317           If you have a LCD backlight connected to the ADP8860, ADP8861 or
 318           ADP8863 say Y here to enable this driver.
 319
 320           To compile this driver as a module, choose M here: the module will
 321           be called adp8860_bl.
 322
 323 config BACKLIGHT_ADP8870
 324         tristate "Backlight Driver for ADP8870 using WLED"
 325         depends on BACKLIGHT_CLASS_DEVICE && I2C
 326         select NEW_LEDS
 327         select LEDS_CLASS
 328         help
 329           If you have a LCD backlight connected to the ADP8870,
 330           say Y here to enable this driver.
 331
 332           To compile this driver as a module, choose M here: the module will
 333           be called adp8870_bl.
 334
 335 config BACKLIGHT_88PM860X
 336         tristate "Backlight Driver for 88PM8606 using WLED"
 337         depends on MFD_88PM860X
 338         help
 339           Say Y to enable the backlight driver for Marvell 88PM8606.
 340
 341 config BACKLIGHT_PCF50633
 342         tristate "Backlight driver for NXP PCF50633 MFD"
 343         depends on BACKLIGHT_CLASS_DEVICE && MFD_PCF50633
 344         help
 345           If you have a backlight driven by a NXP PCF50633 MFD, say Y here to
 346           enable its driver.
 347
 348 config BACKLIGHT_AAT2870
 349         tristate "AnalogicTech AAT2870 Backlight"
 350         depends on BACKLIGHT_CLASS_DEVICE && MFD_AAT2870_CORE
 351         help
 352           If you have a AnalogicTech AAT2870 say Y to enable the
 353           backlight driver.
 354
 355 config BACKLIGHT_LP855X
 356         tristate "Backlight driver for TI LP855X"
 357         depends on BACKLIGHT_CLASS_DEVICE && I2C
 358         help
 359           This supports TI LP8550, LP8551, LP8552, LP8553 and LP8556
 360           backlight driver.
 361
 362 config BACKLIGHT_OT200
 363         tristate "Backlight driver for ot200 visualisation device"
 364         depends on BACKLIGHT_CLASS_DEVICE && CS5535_MFGPT && GPIO_CS5535
 365         help
 366           To compile this driver as a module, choose M here: the module will be
 367           called ot200_bl.
 368
 369 config BACKLIGHT_PANDORA
 370         tristate "Backlight driver for Pandora console"
 371         depends on TWL4030_CORE
 372         help
 373           If you have a Pandora console, say Y to enable the
 374           backlight driver.
 375
 376 endif # BACKLIGHT_CLASS_DEVICE
 377
 378 endif # BACKLIGHT_LCD_SUPPORT