drivers/atm/Kconfig

   1 #
   2 # ATM device configuration
   3 #
   4
   5 menuconfig ATM_DRIVERS
   6         bool "ATM drivers"
   7         depends on NETDEVICES && ATM
   8         default y
   9         ---help---
  10           Say Y here to get to see options for Asynchronous Transfer Mode
  11           device drivers. This option alone does not add any kernel code.
  12
  13           If you say N, all options in this submenu will be skipped and disabled.
  14
  15 if ATM_DRIVERS && NETDEVICES && ATM
  16
  17 config ATM_DUMMY
  18         tristate "Dummy ATM driver"
  19         help
  20           Dummy ATM driver. Useful for proxy signalling, testing,
  21           and development.  If unsure, say N.
  22
  23 config ATM_TCP
  24         tristate "ATM over TCP"
  25         depends on INET
  26         help
  27           ATM over TCP driver. Useful mainly for development and for
  28           experiments. If unsure, say N.
  29
  30 config ATM_LANAI
  31         tristate "Efficient Networks Speedstream 3010"
  32         depends on PCI && ATM
  33         help
  34           Supports ATM cards based on the Efficient Networks "Lanai"
  35           chipset such as the Speedstream 3010 and the ENI-25p.  The
  36           Speedstream 3060 is currently not supported since we don't
  37           have the code to drive the on-board Alcatel DSL chipset (yet).
  38
  39 config ATM_ENI
  40         tristate "Efficient Networks ENI155P"
  41         depends on PCI
  42         ---help---
  43           Driver for the Efficient Networks ENI155p series and SMC ATM
  44           Power155 155 Mbps ATM adapters. Both, the versions with 512KB and
  45           2MB on-board RAM (Efficient calls them "C" and "S", respectively),
  46           and the FPGA and the ASIC Tonga versions of the board are supported.
  47           The driver works with MMF (-MF or ...F) and UTP-5 (-U5 or ...D)
  48           adapters.
  49
  50           To compile this driver as a module, choose M here: the module will
  51           be called eni.
  52
  53 config ATM_ENI_DEBUG
  54         bool "Enable extended debugging"
  55         depends on ATM_ENI
  56         help
  57           Extended debugging records various events and displays that list
  58           when an inconsistency is detected. This mechanism is faster than
  59           generally using printks, but still has some impact on performance.
  60           Note that extended debugging may create certain race conditions
  61           itself. Enable this ONLY if you suspect problems with the driver.
  62
  63 config ATM_ENI_TUNE_BURST
  64         bool "Fine-tune burst settings"
  65         depends on ATM_ENI
  66         ---help---
  67           In order to obtain good throughput, the ENI NIC can transfer
  68           multiple words of data per PCI bus access cycle. Such a multi-word
  69           transfer is called a burst.
  70
  71           The default settings for the burst sizes are suitable for most PCI
  72           chipsets. However, in some cases, large bursts may overrun buffers
  73           in the PCI chipset and cause data corruption. In such cases, large
  74           bursts must be disabled and only (slower) small bursts can be used.
  75           The burst sizes can be set independently in the send (TX) and
  76           receive (RX) direction.
  77
  78           Note that enabling many different burst sizes in the same direction
  79           may increase the cost of setting up a transfer such that the
  80           resulting throughput is lower than when using only the largest
  81           available burst size.
  82
  83           Also, sometimes larger bursts lead to lower throughput, e.g. on an
  84           Intel 440FX board, a drop from 135 Mbps to 103 Mbps was observed
  85           when going from 8W to 16W bursts.
  86
  87 config ATM_ENI_BURST_TX_16W
  88         bool "Enable 16W TX bursts (discouraged)"
  89         depends on ATM_ENI_TUNE_BURST
  90         help
  91           Burst sixteen words at once in the send direction. This may work
  92           with recent PCI chipsets, but is known to fail with older chipsets.
  93
  94 config ATM_ENI_BURST_TX_8W
  95         bool "Enable 8W TX bursts (recommended)"
  96         depends on ATM_ENI_TUNE_BURST
  97         help
  98           Burst eight words at once in the send direction. This is the default
  99           setting.
 100
 101 config ATM_ENI_BURST_TX_4W
 102         bool "Enable 4W TX bursts (optional)"
 103         depends on ATM_ENI_TUNE_BURST
 104         help
 105           Burst four words at once in the send direction. You may want to try
 106           this if you have disabled 8W bursts. Enabling 4W if 8W is also set
 107           may or may not improve throughput.
 108
 109 config ATM_ENI_BURST_TX_2W
 110         bool "Enable 2W TX bursts (optional)"
 111         depends on ATM_ENI_TUNE_BURST
 112         help
 113           Burst two words at once in the send direction. You may want to try
 114           this if you have disabled 4W and 8W bursts. Enabling 2W if 4W or 8W
 115           are also set may or may not improve throughput.
 116
 117 config ATM_ENI_BURST_RX_16W
 118         bool "Enable 16W RX bursts (discouraged)"
 119         depends on ATM_ENI_TUNE_BURST
 120         help
 121           Burst sixteen words at once in the receive direction. This may work
 122           with recent PCI chipsets, but is known to fail with older chipsets.
 123
 124 config ATM_ENI_BURST_RX_8W
 125         bool "Enable 8W RX bursts (discouraged)"
 126         depends on ATM_ENI_TUNE_BURST
 127         help
 128           Burst eight words at once in the receive direction. This may work
 129           with recent PCI chipsets, but is known to fail with older chipsets,
 130           such as the Intel Neptune series.
 131
 132 config ATM_ENI_BURST_RX_4W
 133         bool "Enable 4W RX bursts (recommended)"
 134         depends on ATM_ENI_TUNE_BURST
 135         help
 136           Burst four words at once in the receive direction. This is the
 137           default setting. Enabling 4W if 8W is also set may or may not
 138           improve throughput.
 139
 140 config ATM_ENI_BURST_RX_2W
 141         bool "Enable 2W RX bursts (optional)"
 142         depends on ATM_ENI_TUNE_BURST
 143         help
 144           Burst two words at once in the receive direction. You may want to
 145           try this if you have disabled 4W and 8W bursts. Enabling 2W if 4W or
 146           8W are also set may or may not improve throughput.
 147
 148 config ATM_FIRESTREAM
 149         tristate "Fujitsu FireStream (FS50/FS155) "
 150         depends on PCI && VIRT_TO_BUS
 151         help
 152           Driver for the Fujitsu FireStream 155 (MB86697) and
 153           FireStream 50 (MB86695) ATM PCI chips.
 154
 155           To compile this driver as a module, choose M here: the module will
 156           be called firestream.
 157
 158 config ATM_ZATM
 159         tristate "ZeitNet ZN1221/ZN1225"
 160         depends on PCI && VIRT_TO_BUS
 161         help
 162           Driver for the ZeitNet ZN1221 (MMF) and ZN1225 (UTP-5) 155 Mbps ATM
 163           adapters.
 164
 165           To compile this driver as a module, choose M here: the module will
 166           be called zatm.
 167
 168 config ATM_ZATM_DEBUG
 169         bool "Enable extended debugging"
 170         depends on ATM_ZATM
 171         help
 172           Extended debugging records various events and displays that list
 173           when an inconsistency is detected. This mechanism is faster than
 174           generally using printks, but still has some impact on performance.
 175           Note that extended debugging may create certain race conditions
 176           itself. Enable this ONLY if you suspect problems with the driver.
 177
 178 config ATM_NICSTAR
 179         tristate "IDT 77201 (NICStAR) (ForeRunnerLE)"
 180         depends on PCI
 181         help
 182           The NICStAR chipset family is used in a large number of ATM NICs for
 183           25 and for 155 Mbps, including IDT cards and the Fore ForeRunnerLE
 184           series. Say Y if you have one of those.
 185
 186           To compile this driver as a module, choose M here: the module will
 187           be called nicstar.
 188
 189 config ATM_NICSTAR_USE_SUNI
 190         bool "Use suni PHY driver (155Mbps)"
 191         depends on ATM_NICSTAR
 192         help
 193           Support for the S-UNI and compatible PHYsical layer chips. These are
 194           found in most 155Mbps NICStAR based ATM cards, namely in the
 195           ForeRunner LE155 cards. This driver provides detection of cable~
 196           removal and reinsertion and provides some statistics. This driver
 197           doesn't have removal capability when compiled as a module, so if you
 198           need that capability don't include S-UNI support (it's not needed to
 199           make the card work).
 200
 201 config ATM_NICSTAR_USE_IDT77105
 202         bool "Use IDT77015 PHY driver (25Mbps)"
 203         depends on ATM_NICSTAR
 204         help
 205           Support for the PHYsical layer chip in ForeRunner LE25 cards. In
 206           addition to cable removal/reinsertion detection, this driver allows
 207           you to control the loopback mode of the chip via a dedicated IOCTL.
 208           This driver is required for proper handling of temporary carrier
 209           loss, so if you have a 25Mbps NICStAR based ATM card you must say Y.
 210
 211 config ATM_IDT77252
 212         tristate "IDT 77252 (NICStAR II)"
 213         depends on PCI
 214         help
 215           Driver for the IDT 77252 ATM PCI chips.
 216
 217           To compile this driver as a module, choose M here: the module will
 218           be called idt77252.
 219
 220 config ATM_IDT77252_DEBUG
 221         bool "Enable debugging messages"
 222         depends on ATM_IDT77252
 223         help
 224           Somewhat useful debugging messages are available. The choice of
 225           messages is controlled by a bitmap.  This may be specified as a
 226           module argument.  See the file <file:drivers/atm/idt77252.h> for
 227           the meanings of the bits in the mask.
 228
 229           When active, these messages can have a significant impact on the
 230           speed of the driver, and the size of your syslog files! When
 231           inactive, they will have only a modest impact on performance.
 232
 233 config ATM_IDT77252_RCV_ALL
 234         bool "Receive ALL cells in raw queue"
 235         depends on ATM_IDT77252
 236         help
 237           Enable receiving of all cells on the ATM link, that do not match
 238           an open connection in the raw cell queue of the driver.  Useful
 239           for debugging or special applications only, so the safe answer is N.
 240
 241 config ATM_IDT77252_USE_SUNI
 242         bool
 243         depends on ATM_IDT77252
 244         default y
 245
 246 config ATM_AMBASSADOR
 247         tristate "Madge Ambassador (Collage PCI 155 Server)"
 248         depends on PCI && VIRT_TO_BUS
 249         select BITREVERSE
 250         help
 251           This is a driver for ATMizer based ATM card produced by Madge
 252           Networks Ltd. Say Y (or M to compile as a module named ambassador)
 253           here if you have one of these cards.
 254
 255 config ATM_AMBASSADOR_DEBUG
 256         bool "Enable debugging messages"
 257         depends on ATM_AMBASSADOR
 258         ---help---
 259           Somewhat useful debugging messages are available. The choice of
 260           messages is controlled by a bitmap.  This may be specified as a
 261           module argument (kernel command line argument as well?), changed
 262           dynamically using an ioctl (not yet) or changed by sending the
 263           string "Dxxxx" to VCI 1023 (where x is a hex digit).  See the file
 264           <file:drivers/atm/ambassador.h> for the meanings of the bits in the
 265           mask.
 266
 267           When active, these messages can have a significant impact on the
 268           speed of the driver, and the size of your syslog files! When
 269           inactive, they will have only a modest impact on performance.
 270
 271 config ATM_HORIZON
 272         tristate "Madge Horizon [Ultra] (Collage PCI 25 and Collage PCI 155 Client)"
 273         depends on PCI && VIRT_TO_BUS
 274         help
 275           This is a driver for the Horizon chipset ATM adapter cards once
 276           produced by Madge Networks Ltd. Say Y (or M to compile as a module
 277           named horizon) here if you have one of these cards.
 278
 279 config ATM_HORIZON_DEBUG
 280         bool "Enable debugging messages"
 281         depends on ATM_HORIZON
 282         ---help---
 283           Somewhat useful debugging messages are available. The choice of
 284           messages is controlled by a bitmap.  This may be specified as a
 285           module argument (kernel command line argument as well?), changed
 286           dynamically using an ioctl (not yet) or changed by sending the
 287           string "Dxxxx" to VCI 1023 (where x is a hex digit).  See the file
 288           <file:drivers/atm/horizon.h> for the meanings of the bits in the
 289           mask.
 290
 291           When active, these messages can have a significant impact on the
 292           speed of the driver, and the size of your syslog files! When
 293           inactive, they will have only a modest impact on performance.
 294
 295 config ATM_IA
 296         tristate "Interphase ATM PCI x575/x525/x531"
 297         depends on PCI
 298         ---help---
 299           This is a driver for the Interphase (i)ChipSAR adapter cards
 300           which include a variety of variants in term of the size of the
 301           control memory (128K-1KVC, 512K-4KVC), the size of the packet
 302           memory (128K, 512K, 1M), and the PHY type (Single/Multi mode OC3,
 303           UTP155, UTP25, DS3 and E3). Go to:
 304                 <http://www.iphase.com/>
 305           for more info about the cards. Say Y (or M to compile as a module
 306           named iphase) here if you have one of these cards.
 307
 308           See the file <file:Documentation/networking/iphase.txt> for further
 309           details.
 310
 311 config ATM_IA_DEBUG
 312         bool "Enable debugging messages"
 313         depends on ATM_IA
 314         ---help---
 315           Somewhat useful debugging messages are available. The choice of
 316           messages is controlled by a bitmap. This may be specified as a
 317           module argument (kernel command line argument as well?), changed
 318           dynamically using an ioctl (Get the debug utility, iadbg, from
 319           <ftp://ftp.iphase.com/pub/atm/pci/>).
 320
 321           See the file <file:drivers/atm/iphase.h> for the meanings of the
 322           bits in the mask.
 323
 324           When active, these messages can have a significant impact on the
 325           speed of the driver, and the size of your syslog files! When
 326           inactive, they will have only a modest impact on performance.
 327
 328 config ATM_FORE200E
 329         tristate "FORE Systems 200E-series"
 330         depends on (PCI || SBUS)
 331         select FW_LOADER
 332         ---help---
 333           This is a driver for the FORE Systems 200E-series ATM adapter
 334           cards. It simultaneously supports PCA-200E and SBA-200E models
 335           on PCI and SBUS hosts. Say Y (or M to compile as a module
 336           named fore_200e) here if you have one of these ATM adapters.
 337
 338           See the file <file:Documentation/networking/fore200e.txt> for
 339           further details.
 340
 341 config ATM_FORE200E_USE_TASKLET
 342         bool "Defer interrupt work to a tasklet"
 343         depends on ATM_FORE200E
 344         default n
 345         help
 346           This defers work to be done by the interrupt handler to a
 347           tasklet instead of handling everything at interrupt time.  This
 348           may improve the responsive of the host.
 349
 350 config ATM_FORE200E_TX_RETRY
 351         int "Maximum number of tx retries"
 352         depends on ATM_FORE200E
 353         default "16"
 354         ---help---
 355           Specifies the number of times the driver attempts to transmit
 356           a message before giving up, if the transmit queue of the ATM card
 357           is transiently saturated.
 358
 359           Saturation of the transmit queue may occur only under extreme
 360           conditions, e.g. when a fast host continuously submits very small
 361           frames (<64 bytes) or raw AAL0 cells (48 bytes) to the ATM adapter.
 362
 363           Note that under common conditions, it is unlikely that you encounter
 364           a saturation of the transmit queue, so the retry mechanism never
 365           comes into play.
 366
 367 config ATM_FORE200E_DEBUG
 368         int "Debugging level (0-3)"
 369         depends on ATM_FORE200E
 370         default "0"
 371         help
 372           Specifies the level of debugging messages issued by the driver.
 373           The verbosity of the driver increases with the value of this
 374           parameter.
 375
 376           When active, these messages can have a significant impact on
 377           the performances of the driver, and the size of your syslog files!
 378           Keep the debugging level to 0 during normal operations.
 379
 380 config ATM_HE
 381         tristate "ForeRunner HE Series"
 382         depends on PCI
 383         help
 384           This is a driver for the Marconi ForeRunner HE-series ATM adapter
 385           cards. It simultaneously supports the 155 and 622 versions.
 386
 387 config ATM_HE_USE_SUNI
 388         bool "Use S/UNI PHY driver"
 389         depends on ATM_HE
 390         help
 391           Support for the S/UNI-Ultra and S/UNI-622 found in the ForeRunner
 392           HE cards.  This driver provides carrier detection some statistics.
 393
 394 config ATM_SOLOS
 395         tristate "Solos ADSL2+ PCI Multiport card driver"
 396         depends on PCI
 397         select FW_LOADER
 398         help
 399           Support for the Solos multiport ADSL2+ card.
 400
 401 endif # ATM