2 # Physical Layer USB driver configuration
4 menu "USB Physical Layer drivers"
10 config USB_OTG_WAKELOCK
11 bool "Hold a wakelock when USB connected"
12 depends on PM_WAKELOCKS
15 Select this to automatically hold a wakelock when USB is
16 connected, preventing suspend.
19 # USB Transceiver Drivers
22 tristate "AB8500 USB Transceiver Driver"
23 depends on AB8500_CORE
26 Enable this to support the USB OTG transceiver in AB8500 chip.
27 This transceiver supports high and full speed devices plus,
28 in host mode, low speed.
31 bool "Freescale USB OTG Transceiver Driver"
32 depends on USB_EHCI_FSL && USB_FSL_USB2 && USB_OTG_FSM=y && PM
33 depends on USB_GADGET || !USB_GADGET # if USB_GADGET=m, this can't be 'y'
36 Enable this to support Freescale USB OTG transceiver.
39 tristate "Philips ISP1301 with OMAP OTG"
40 depends on I2C && ARCH_OMAP_OTG
42 depends on USB_GADGET || !USB_GADGET # if USB_GADGET=m, this can't be 'y'
45 If you say yes here you get support for the Philips ISP1301
46 USB-On-The-Go transceiver working with the OMAP OTG controller.
47 The ISP1301 is a full speed USB transceiver which is used in
48 products including H2, H3, and H4 development boards for Texas
49 Instruments OMAP processors.
51 This driver can also be built as a module. If so, the module
52 will be called phy-isp1301-omap.
54 config KEYSTONE_USB_PHY
55 tristate "Keystone USB PHY Driver"
56 depends on ARCH_KEYSTONE || COMPILE_TEST
57 depends on NOP_USB_XCEIV
59 Enable this to support Keystone USB phy. This driver provides
60 interface to interact with USB 2.0 and USB 3.0 PHY that is part
64 tristate "NOP USB Transceiver Driver"
65 depends on USB_GADGET || !USB_GADGET # if USB_GADGET=m, NOP can't be built-in
68 This driver is to be used by all the usb transceiver which are either
69 built-in with usb ip or which are autonomous and doesn't require any
70 phy programming such as ISP1x04 etc.
72 config AM335X_CONTROL_USB
76 tristate "AM335x USB PHY Driver"
77 depends on ARM || COMPILE_TEST
78 depends on NOP_USB_XCEIV
80 select AM335X_CONTROL_USB
83 This driver provides PHY support for that phy which part for the
87 tristate "TWL6030 USB Transceiver Driver"
88 depends on TWL4030_CORE && OMAP_USB2 && USB_MUSB_OMAP2PLUS
91 Enable this to support the USB OTG transceiver on TWL6030
92 family chips. This TWL6030 transceiver has the VBUS and ID GND
93 and OTG SRP events capabilities. For all other transceiver functionality
94 UTMI PHY is embedded in OMAP4430. The internal PHY configurations APIs
95 are hooked to this driver through platform_data structure.
96 The definition of internal PHY APIs are in the mach-omap2 layer.
99 tristate "GPIO based peripheral-only VBUS sensing 'transceiver'"
100 depends on GPIOLIB || COMPILE_TEST
101 depends on USB_GADGET || !USB_GADGET # if USB_GADGET=m, this can't be 'y'
104 Provides simple GPIO VBUS sensing for controllers with an
105 internal transceiver via the usb_phy interface, and
106 optionally control of a D+ pullup GPIO as well as a VBUS
107 current limit regulator.
110 tristate "OMAP USB OTG controller driver"
111 depends on ARCH_OMAP_OTG && EXTCON
113 Enable this to support some transceivers on OMAP1 platforms. OTG
114 controller is needed to switch between host and peripheral modes.
116 This driver can also be built as a module. If so, the module
117 will be called phy-omap-otg.
120 tristate "Tahvo USB transceiver driver"
122 depends on USB_GADGET || !USB_GADGET # if USB_GADGET=m, this can't be 'y'
125 Enable this to support USB transceiver on Tahvo. This is used
126 at least on Nokia 770.
128 config TAHVO_USB_HOST_BY_DEFAULT
130 bool "Device in USB host mode by default"
132 Say Y here, if you want the device to enter USB host mode
133 by default on bootup.
136 tristate "NXP ISP1301 USB transceiver support"
137 depends on USB || USB_GADGET
141 Say Y here to add support for the NXP ISP1301 USB transceiver driver.
142 This chip is typically used as USB transceiver for USB host, gadget
143 and OTG drivers (to be selected separately).
145 To compile this driver as a module, choose M here: the
146 module will be called phy-isp1301.
149 tristate "Qualcomm on-chip USB OTG controller support"
150 depends on (USB || USB_GADGET) && (ARCH_QCOM || COMPILE_TEST)
151 depends on USB_GADGET || !USB_GADGET # if USB_GADGET=m, this can't be 'y'
152 depends on RESET_CONTROLLER
155 Enable this to support the USB OTG transceiver on Qualcomm chips. It
156 handles PHY initialization, clock management, and workarounds
157 required after resetting the hardware and power management.
158 This driver is required even for peripheral only or host only
160 This driver is not supported on boards like trout which
163 config USB_QCOM_8X16_PHY
164 tristate "Qualcomm APQ8016/MSM8916 on-chip USB PHY controller support"
165 depends on ARCH_QCOM || COMPILE_TEST
166 depends on RESET_CONTROLLER
168 select USB_ULPI_VIEWPORT
170 Enable this to support the USB transceiver on Qualcomm 8x16 chipsets.
171 It handles PHY initialization, clock management, power management,
172 and workarounds required after resetting the hardware.
174 To compile this driver as a module, choose M here: the
175 module will be called phy-qcom-8x16-usb.
178 tristate "Marvell USB OTG support"
179 depends on USB_EHCI_MV && USB_MV_UDC && PM && USB_OTG
180 depends on USB_GADGET || !USB_GADGET # if USB_GADGET=m, this can't be 'y'
183 Say Y here if you want to build Marvell USB OTG transciever
184 driver in kernel (including PXA and MMP series). This driver
185 implements role switch between EHCI host driver and gadget driver.
187 To compile this driver as a module, choose M here.
190 tristate "Freescale MXS USB PHY support"
191 depends on ARCH_MXC || ARCH_MXS
195 Enable this to support the Freescale MXS USB PHY.
197 MXS Phy is used by some of the i.MX SoCs, for example imx23/28/6x.
200 bool "Generic ULPI Transceiver Driver"
201 depends on ARM || ARM64
202 select USB_ULPI_VIEWPORT
204 Enable this to support ULPI connected USB OTG transceivers which
205 are likely found on embedded boards.
207 config USB_ULPI_VIEWPORT
210 Provides read/write operations to the ULPI phy register set for
211 controllers with a viewport register (e.g. Chipidea/ARC controllers).
213 config DUAL_ROLE_USB_INTF
214 bool "Generic DUAL ROLE sysfs interface"
215 depends on SYSFS && USB_PHY
217 A generic sysfs interface to track and change the state of
218 dual role usb phys. The usb phy drivers can register to
219 this interface to expose it capabilities to the userspace
220 and thereby allowing userspace to change the port mode.