8139*/atp/r8169/sc92031: Move the Realtek drivers

[GitHub/mt8127/android_kernel_alcatel_ttab.git] / drivers / net / Kconfig

diff --git a/drivers/net/Kconfig b/drivers/net/Kconfig
index 8da9f9620680fb83c5562a26ace4ed0e8b384cc6..42408d7dc1c25696981e4728464f72e608b041b3 100644 (file)
--- a/drivers/net/Kconfig
+++ b/drivers/net/Kconfig
@@ -594,73 +594,6 @@ config FEALNX
          Say Y here to support the Myson MTD-800 family of PCI-based Ethernet 
          cards. <http://www.myson.com.tw/>
 
-config 8139CP
-       tristate "RealTek RTL-8139 C+ PCI Fast Ethernet Adapter support (EXPERIMENTAL)"
-       depends on NET_PCI && PCI && EXPERIMENTAL
-       select CRC32
-       select MII
-       help
-         This is a driver for the Fast Ethernet PCI network cards based on
-         the RTL8139C+ chips. If you have one of those, say Y and read
-         the Ethernet-HOWTO, available from
-         <http://www.tldp.org/docs.html#howto>.
-
-         To compile this driver as a module, choose M here: the module
-         will be called 8139cp.  This is recommended.
-
-config 8139TOO
-       tristate "RealTek RTL-8129/8130/8139 PCI Fast Ethernet Adapter support"
-       depends on NET_PCI && PCI
-       select CRC32
-       select MII
-       ---help---
-         This is a driver for the Fast Ethernet PCI network cards based on
-         the RTL 8129/8130/8139 chips. If you have one of those, say Y and
-         read the Ethernet-HOWTO <http://www.tldp.org/docs.html#howto>.
-
-         To compile this driver as a module, choose M here: the module
-         will be called 8139too.  This is recommended.
-
-config 8139TOO_PIO
-       bool "Use PIO instead of MMIO"
-       default y
-       depends on 8139TOO
-       help
-         This instructs the driver to use programmed I/O ports (PIO) instead
-         of PCI shared memory (MMIO).  This can possibly solve some problems
-         in case your mainboard has memory consistency issues.  If unsure,
-         say N.
-
-config 8139TOO_TUNE_TWISTER
-       bool "Support for uncommon RTL-8139 rev. K (automatic channel equalization)"
-       depends on 8139TOO
-       help
-         This implements a function which might come in handy in case you
-         are using low quality on long cabling. It is required for RealTek
-         RTL-8139 revision K boards, and totally unused otherwise.  It tries
-         to match the transceiver to the cable characteristics. This is
-         experimental since hardly documented by the manufacturer.
-         If unsure, say Y.
-
-config 8139TOO_8129
-       bool "Support for older RTL-8129/8130 boards"
-       depends on 8139TOO
-       help
-         This enables support for the older and uncommon RTL-8129 and
-         RTL-8130 chips, which support MII via an external transceiver,
-         instead of an internal one.  Disabling this option will save some
-         memory by making the code size smaller.  If unsure, say Y.
-
-config 8139_OLD_RX_RESET
-       bool "Use older RX-reset method"
-       depends on 8139TOO
-       help
-         The 8139too driver was recently updated to contain a more rapid
-         reset sequence, in the face of severe receive errors.  This "new"
-         RX-reset method should be adequate for all boards.  But if you
-         experience problems, you can enable this option to restore the
-         old RX-reset behavior.  If unsure, say N.
-
 config R6040
        tristate "RDC R6040 Fast Ethernet Adapter support"
        depends on NET_PCI && PCI
@@ -776,18 +709,6 @@ config VIA_RHINE_MMIO
 
          If unsure, say Y.
 
-config SC92031
-       tristate "Silan SC92031 PCI Fast Ethernet Adapter driver (EXPERIMENTAL)"
-       depends on NET_PCI && PCI && EXPERIMENTAL
-       select CRC32
-       ---help---
-         This is a driver for the Fast Ethernet PCI network cards based on
-         the Silan SC92031 chip (sometimes also called Rsltek 8139D). If you
-         have one of these, say Y here.
-
-         To compile this driver as a module, choose M here: the module
-         will be called sc92031.  This is recommended.
-
 config CPMAC
        tristate "TI AR7 CPMAC Ethernet support (EXPERIMENTAL)"
        depends on NET_ETHERNET && EXPERIMENTAL && AR7
@@ -819,21 +740,6 @@ config NET_POCKET
          the questions about this class of network devices. If you say Y, you
          will be asked for your specific device in the following questions.
 
-config ATP
-       tristate "AT-LAN-TEC/RealTek pocket adapter support"
-       depends on NET_POCKET && PARPORT && X86
-       select CRC32
-       ---help---
-         This is a network (Ethernet) device which attaches to your parallel
-         port. Read <file:drivers/net/atp.c> as well as the Ethernet-HOWTO,
-         available from <http://www.tldp.org/docs.html#howto>, if you
-         want to use this.  If you intend to use this driver, you should have
-         said N to the "Parallel printer support", because the two drivers
-         don't like each other.
-
-         To compile this driver as a module, choose M here: the module
-         will be called atp.
-
 config DE600
        tristate "D-Link DE600 pocket adapter support"
        depends on NET_POCKET && PARPORT
@@ -1006,18 +912,6 @@ config YELLOWFIN
          To compile this driver as a module, choose M here: the module
          will be called yellowfin.  This is recommended.
 
-config R8169
-       tristate "Realtek 8169 gigabit ethernet support"
-       depends on PCI
-       select FW_LOADER
-       select CRC32
-       select MII
-       ---help---
-         Say Y here if you have a Realtek 8169 PCI Gigabit Ethernet adapter.
-
-         To compile this driver as a module, choose M here: the module
-         will be called r8169.  This is recommended.
-
 config SIS190
        tristate "SiS190/SiS191 gigabit ethernet support"
        depends on PCI