[GitHub/mt8127/android_kernel_alcatel_ttab.git] / drivers / mtd / nand / r852.h

/*
 * Copyright © 2009 - Maxim Levitsky
 * driver for Ricoh xD readers
 *
 * This program is free software; you can redistribute it and/or modify
 * it under the terms of the GNU General Public License version 2 as
 * published by the Free Software Foundation.
 */

#include <linux/pci.h>
#include <linux/completion.h>
#include <linux/workqueue.h>
#include <linux/mtd/nand.h>
#include <linux/spinlock.h>


/* nand interface + ecc
   byte write/read does one cycle on nand data lines.
   dword write/read does 4 cycles
   if R852_CTL_ECC_ACCESS is set in R852_CTL, then dword read reads
   results of ecc correction, if DMA read was done before.
   If write was done two dword reads read generated ecc checksums
*/
#define	R852_DATALINE		0x00

/* control register */
#define R852_CTL		0x04
#define R852_CTL_COMMAND 	0x01	/* send command (#CLE)*/
#define R852_CTL_DATA		0x02	/* read/write data (#ALE)*/
#define R852_CTL_ON		0x04	/* only seem to controls the hd led, */
					/* but has to be set on start...*/
#define R852_CTL_RESET		0x08	/* unknown, set only on start once*/
#define R852_CTL_CARDENABLE	0x10	/* probably (#CE) - always set*/
#define R852_CTL_ECC_ENABLE	0x20	/* enable ecc engine */
#define R852_CTL_ECC_ACCESS	0x40	/* read/write ecc via reg #0*/
#define R852_CTL_WRITE		0x80	/* set when performing writes (#WP) */

/* card detection status */
#define R852_CARD_STA		0x05

#define R852_CARD_STA_CD	0x01	/* state of #CD line, same as 0x04 */
#define R852_CARD_STA_RO	0x02	/* card is readonly */
#define R852_CARD_STA_PRESENT	0x04	/* card is present (#CD) */
#define R852_CARD_STA_ABSENT	0x08	/* card is absent */
#define R852_CARD_STA_BUSY	0x80	/* card is busy - (#R/B) */

/* card detection irq status & enable*/
#define R852_CARD_IRQ_STA	0x06	/* IRQ status */
#define R852_CARD_IRQ_ENABLE	0x07	/* IRQ enable */

#define R852_CARD_IRQ_CD	0x01	/* fire when #CD lights, same as 0x04*/
#define R852_CARD_IRQ_REMOVE	0x04	/* detect card removal */
#define R852_CARD_IRQ_INSERT	0x08	/* detect card insert */
#define R852_CARD_IRQ_UNK1	0x10	/* unknown */
#define R852_CARD_IRQ_GENABLE	0x80	/* general enable */
#define R852_CARD_IRQ_MASK	0x1D


/* hardware enable */
#define R852_HW			0x08
#define R852_HW_ENABLED		0x01	/* hw enabled */
#define R852_HW_UNKNOWN		0x80


/* dma capabilities */
#define R852_DMA_CAP		0x09
#define R852_SMBIT		0x20	/* if set with bit #6 or bit #7, then */
					/* hw is smartmedia */
#define R852_DMA1		0x40	/* if set w/bit #7, dma is supported */
#define R852_DMA2		0x80	/* if set w/bit #6, dma is supported */


/* physical DMA address - 32 bit value*/
#define R852_DMA_ADDR		0x0C


/* dma settings */
#define R852_DMA_SETTINGS	0x10
#define R852_DMA_MEMORY		0x01	/* (memory <-> internal hw buffer) */
#define R852_DMA_READ		0x02	/* 0 = write, 1 = read */
#define R852_DMA_INTERNAL	0x04	/* (internal hw buffer <-> card) */

/* dma IRQ status */
#define R852_DMA_IRQ_STA		0x14

/* dma IRQ enable */
#define R852_DMA_IRQ_ENABLE	0x18

#define R852_DMA_IRQ_MEMORY	0x01	/* (memory <-> internal hw buffer) */
#define R852_DMA_IRQ_ERROR	0x02	/* error did happen */
#define R852_DMA_IRQ_INTERNAL	0x04	/* (internal hw buffer <-> card) */
#define R852_DMA_IRQ_MASK	0x07	/* mask of all IRQ bits */


/* ECC syndrome format - read from reg #0 will return two copies of these for
   each half of the page.
   first byte is error byte location, and second, bit location + flags */
#define R852_ECC_ERR_BIT_MSK	0x07	/* error bit location */
#define R852_ECC_CORRECT		0x10	/* no errors - (guessed) */
#define R852_ECC_CORRECTABLE	0x20	/* correctable error exist */
#define R852_ECC_FAIL		0x40	/* non correctable error detected */

#define R852_DMA_LEN		512

#define DMA_INTERNAL	0
#define DMA_MEMORY	1

struct r852_device {
	void __iomem *mmio;		/* mmio */
	struct mtd_info *mtd;		/* mtd backpointer */
	struct nand_chip *chip;		/* nand chip backpointer */
	struct pci_dev *pci_dev;	/* pci backpointer */

	/* dma area */
	dma_addr_t phys_dma_addr;	/* bus address of buffer*/
	struct completion dma_done;	/* data transfer done */

	dma_addr_t phys_bounce_buffer;	/* bus address of bounce buffer */
	uint8_t *bounce_buffer;		/* virtual address of bounce buffer */

	int dma_dir;			/* 1 = read, 0 = write */
	int dma_stage;			/* 0 - idle, 1 - first step,
					   2 - second step */

	int dma_state;			/* 0 = internal, 1 = memory */
	int dma_error;			/* dma errors */
	int dma_usable;			/* is it possible to use dma */

	/* card status area */
	struct delayed_work card_detect_work;
	struct workqueue_struct *card_workqueue;
	int card_registred;		/* card registered with mtd */
	int card_detected;		/* card detected in slot */
	int card_unstable;		/* whenever the card is inserted,
					   is not known yet */
	int readonly;			/* card is readonly */
	int sm;				/* Is card smartmedia */

	/* interrupt handling */
	spinlock_t irqlock;		/* IRQ protecting lock */
	int irq;			/* irq num */
	/* misc */
	void *tmp_buffer;		/* temporary buffer */
	uint8_t ctlreg;			/* cached contents of control reg */
};

#define DRV_NAME "r852"


#define dbg(format, ...) \
	if (debug) \
		printk(KERN_DEBUG DRV_NAME ": " format "\n", ## __VA_ARGS__)

#define dbg_verbose(format, ...) \
	if (debug > 1) \
		printk(KERN_DEBUG DRV_NAME ": " format "\n", ## __VA_ARGS__)


#define message(format, ...) \
	printk(KERN_INFO DRV_NAME ": " format "\n", ## __VA_ARGS__)
Commit	Line	Data
67e054e9 ML	1	/*
	2	* Copyright © 2009 - Maxim Levitsky
	3	* driver for Ricoh xD readers
	4	*
	5	* This program is free software; you can redistribute it and/or modify
	6	* it under the terms of the GNU General Public License version 2 as
	7	* published by the Free Software Foundation.
	8	*/
	9
	10	#include <linux/pci.h>
	11	#include <linux/completion.h>
	12	#include <linux/workqueue.h>
	13	#include <linux/mtd/nand.h>
	14	#include <linux/spinlock.h>
	15
	16
	17	/* nand interface + ecc
	18	byte write/read does one cycle on nand data lines.
	19	dword write/read does 4 cycles
	20	if R852_CTL_ECC_ACCESS is set in R852_CTL, then dword read reads
	21	results of ecc correction, if DMA read was done before.
	22	If write was done two dword reads read generated ecc checksums
	23	*/
	24	#define R852_DATALINE 0x00
	25
	26	/* control register */
	27	#define R852_CTL 0x04
	28	#define R852_CTL_COMMAND 0x01 /* send command (#CLE)*/
	29	#define R852_CTL_DATA 0x02 /* read/write data (#ALE)*/
	30	#define R852_CTL_ON 0x04 /* only seem to controls the hd led, */
	31	/* but has to be set on start...*/
	32	#define R852_CTL_RESET 0x08 /* unknown, set only on start once*/
	33	#define R852_CTL_CARDENABLE 0x10 /* probably (#CE) - always set*/
	34	#define R852_CTL_ECC_ENABLE 0x20 /* enable ecc engine */
	35	#define R852_CTL_ECC_ACCESS 0x40 /* read/write ecc via reg #0*/
	36	#define R852_CTL_WRITE 0x80 /* set when performing writes (#WP) */
	37
	38	/* card detection status */
	39	#define R852_CARD_STA 0x05
	40
	41	#define R852_CARD_STA_CD 0x01 /* state of #CD line, same as 0x04 */
	42	#define R852_CARD_STA_RO 0x02 /* card is readonly */
	43	#define R852_CARD_STA_PRESENT 0x04 /* card is present (#CD) */
	44	#define R852_CARD_STA_ABSENT 0x08 /* card is absent */
	45	#define R852_CARD_STA_BUSY 0x80 /* card is busy - (#R/B) */
	46
	47	/* card detection irq status & enable*/
	48	#define R852_CARD_IRQ_STA 0x06 /* IRQ status */
	49	#define R852_CARD_IRQ_ENABLE 0x07 /* IRQ enable */
	50
	51	#define R852_CARD_IRQ_CD 0x01 /* fire when #CD lights, same as 0x04*/
	52	#define R852_CARD_IRQ_REMOVE 0x04 /* detect card removal */
	53	#define R852_CARD_IRQ_INSERT 0x08 /* detect card insert */
	54	#define R852_CARD_IRQ_UNK1 0x10 /* unknown */
	55	#define R852_CARD_IRQ_GENABLE 0x80 /* general enable */
	56	#define R852_CARD_IRQ_MASK 0x1D
	57
	58
	59
	60	/* hardware enable */
	61	#define R852_HW 0x08
	62	#define R852_HW_ENABLED 0x01 /* hw enabled */
	63	#define R852_HW_UNKNOWN 0x80
	64
65
66	/* dma capabilities */
67	#define R852_DMA_CAP 0x09
68	#define R852_SMBIT 0x20 /* if set with bit #6 or bit #7, then */
69	/* hw is smartmedia */
70	#define R852_DMA1 0x40 /* if set w/bit #7, dma is supported */
71	#define R852_DMA2 0x80 /* if set w/bit #6, dma is supported */
72
73
74	/* physical DMA address - 32 bit value*/
75	#define R852_DMA_ADDR 0x0C
76
77
78	/* dma settings */
79	#define R852_DMA_SETTINGS 0x10
80	#define R852_DMA_MEMORY 0x01 /* (memory <-> internal hw buffer) */
81	#define R852_DMA_READ 0x02 /* 0 = write, 1 = read */
82	#define R852_DMA_INTERNAL 0x04 /* (internal hw buffer <-> card) */
83
84	/* dma IRQ status */
85	#define R852_DMA_IRQ_STA 0x14
86
87	/* dma IRQ enable */
88	#define R852_DMA_IRQ_ENABLE 0x18
89
90	#define R852_DMA_IRQ_MEMORY 0x01 /* (memory <-> internal hw buffer) */
91	#define R852_DMA_IRQ_ERROR 0x02 /* error did happen */
92	#define R852_DMA_IRQ_INTERNAL 0x04 /* (internal hw buffer <-> card) */
93	#define R852_DMA_IRQ_MASK 0x07 /* mask of all IRQ bits */
94
95
96	/* ECC syndrome format - read from reg #0 will return two copies of these for
97	each half of the page.
98	first byte is error byte location, and second, bit location + flags */
99	#define R852_ECC_ERR_BIT_MSK 0x07 /* error bit location */
100	#define R852_ECC_CORRECT 0x10 /* no errors - (guessed) */
101	#define R852_ECC_CORRECTABLE 0x20 /* correctable error exist */
102	#define R852_ECC_FAIL 0x40 /* non correctable error detected */
103
104	#define R852_DMA_LEN 512
105
106	#define DMA_INTERNAL 0
107	#define DMA_MEMORY 1
108
109	struct r852_device {
110	void __iomem mmio; / mmio */
111	struct mtd_info mtd; / mtd backpointer */
112	struct nand_chip chip; / nand chip backpointer */
113	struct pci_dev pci_dev; / pci backpointer */
114
115	/* dma area */
116	dma_addr_t phys_dma_addr; /* bus address of buffer*/
117	struct completion dma_done; /* data transfer done */
118
119	dma_addr_t phys_bounce_buffer; /* bus address of bounce buffer */
120	uint8_t bounce_buffer; / virtual address of bounce buffer */
121
122	int dma_dir; /* 1 = read, 0 = write */
123	int dma_stage; /* 0 - idle, 1 - first step,
124	2 - second step */
125
126	int dma_state; /* 0 = internal, 1 = memory */
127	int dma_error; /* dma errors */
128	int dma_usable; /* is it possible to use dma */
129
130	/* card status area */
131	struct delayed_work card_detect_work;
132	struct workqueue_struct *card_workqueue;
133	int card_registred; /* card registered with mtd */
134	int card_detected; /* card detected in slot */
135	int card_unstable; /* whenever the card is inserted,
136	is not known yet */
137	int readonly; /* card is readonly */
138	int sm; /* Is card smartmedia */
139
140	/* interrupt handling */
141	spinlock_t irqlock; /* IRQ protecting lock */
142	int irq; /* irq num */
67e054e9 ML	143	/* misc */
	144	void tmp_buffer; / temporary buffer */
	145	uint8_t ctlreg; /* cached contents of control reg */
	146	};
	147
	148	#define DRV_NAME "r852"
	149
	150
	151	#define dbg(format, ...) \
	152	if (debug) \
	153	printk(KERN_DEBUG DRV_NAME ": " format "\n", ## __VA_ARGS__)
	154
	155	#define dbg_verbose(format, ...) \
	156	if (debug > 1) \
	157	printk(KERN_DEBUG DRV_NAME ": " format "\n", ## __VA_ARGS__)
	158
	159
	160	#define message(format, ...) \
	161	printk(KERN_INFO DRV_NAME ": " format "\n", ## __VA_ARGS__)