Olof Johansson [Mon, 19 Jun 2017 03:40:35 +0000 (20:40 -0700)]
Merge tag 'sunxi-dt-for-4.13' of https://git./linux/kernel/git/sunxi/linux into next/dt
Allwinner DT changes for 4.13
The usual chunk of patches. The most notable improvements are the power
supplies improvements (battery and AC-IN), crypto support for the sun5i
family, HDMI support for the A10s, plus a lot of new things for the V3S and
the A83T.
* tag 'sunxi-dt-for-4.13' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux: (47 commits)
ARM: sun6i: a31s: primo81: Enable battery power supply
ARM: sun6i: a31s: primo81: Change USB OTG to OTG mode
ARM: sun8i: a83t: Add dt node for the syscon control module
ARM: sun8i: a83t: Add device node for R_PIO
ARM: sun8i: v3s: add device nodes for DE2 display pipeline
ARM: dts: sunxi: add SoC specific compatibles for the crypto nodes
ARM: sun5i: add a cryptographic engine node
ARM: sun8i: a83t: Add device node for PRCM
ARM: dts: sun8i: h3: Add initial NanoPi M1 Plus support
ARM: dts: orange-pi-zero: add node for SPI NOR
ARM: sun7i: a20: cubietruck: Tie AXP209's USB power supply to USB PHY
ARM: sun6i: a31: hummingbird: Enable AXP221's ACIN power supply
ARM: sun4i: a10: cubieboard: Enable AXP209's ACIN power supply
ARM: sun7i: a20: bananapi-m1-plus: Enable AXP209's ACIN power supply
ARM: sun7i: a20: cubieboard2: Enable AXP209's ACIN power supply
ARM: sun7i: a20: cubieboard2: Move usb_otg node for alphabetical ordering
ARM: sun8i: a83t: cubietruck-plus: Enable SPDIF output
ARM: sun8i: a83t: cubietruck-plus: Add LED device nodes
ARM: sun8i: a83t: Add device node for SPDIF transmitter
ARM: sun8i: a83t: Add device node for DMA controller
...
Signed-off-by: Olof Johansson <olof@lixom.net>
Olof Johansson [Mon, 19 Jun 2017 03:37:56 +0000 (20:37 -0700)]
Merge tag 'amlogic-dt' of git://git./linux/kernel/git/khilman/linux-amlogic into next/dt
Amlogic 32-bit DT changes for v4.13:
- minor reorganization to support different busses
- add/use real clock controller
* tag 'amlogic-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-amlogic:
ARM: dts: meson8: add and use the real clock controller
ARM: dts: meson: Extend L2 cache controller node for Meson8 and Meson8b
ARM: dts: meson8b: inherit meson.dtsi from meson8b.dtsi
ARM: dts: meson: organize devices in their corresponding busses
Signed-off-by: Olof Johansson <olof@lixom.net>
Olof Johansson [Mon, 19 Jun 2017 03:31:59 +0000 (20:31 -0700)]
Merge tag 'gemini-v4.13-dts-2' of git://git./linux/kernel/git/linusw/linux-nomadik into next/dt
Gemini DTS patches for v4.13, take 2:
- Add DMA controller
- Add PATA controller and SATA bridge
* tag 'gemini-v4.13-dts-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-nomadik:
ARM: dts: add Gemini PATA/SATA support
ARM: dts: Add Gemini DMA controller
Signed-off-by: Olof Johansson <olof@lixom.net>
Olof Johansson [Mon, 19 Jun 2017 03:15:54 +0000 (20:15 -0700)]
Merge tag 'arm-soc/for-4.13/devicetree' of github.com/Broadcom/stblinux into next/dt
This pull request contains Broadcom ARM-based Device Tree changes for 4.13.
Note that Baruch's changes are fixes that are currently included in v4.12-rc2,
but they are also included here in order to keep this tag based off v4.12-rc1.
Please pull the following:
- Rafal adds CPU and thermal zones to the Northstar (BCM5301X) Device Tree and he
also adds the MDIO controller nodes for later use by USB PHYs
- Eric adds support for the V3D engine and Ethernet switch on the Cygnus
platforms, he also adds a set of Device Tree sources and include files for the
Raspberry Pi 3 (BCM2837) to be used with the ARM/Linux kernel,
- Jon adds CPU and thermal zones to the Northstar Plus Device Tree files
- Stefan updates the Raspberry Pi DTS files with thermal trip points and zones,
adds support for the USB OTG on the Raspberry Pi Zero which includes the
proper dwc2 configuration, a generic USB PHY and finally the enabling of the
OTG controller by including the proper DTS include file
- Gerd switches the Raspberry Pi DTS files to use the SDHOST controller (faster
than the SDHCI)
* tag 'arm-soc/for-4.13/devicetree' of http://github.com/Broadcom/stblinux:
ARM: dts: bcm2835-rpi-zero: Enable OTG mode
ARM: dts: bcm283x: Add generic USB PHY
ARM: dts: bcm283x: Add dtsi for OTG mode
ARM: dts: Cygnus: Add the ethernet switch and ethernet PHY
ARM: dts: NSP: Add Thermal Support
ARM: dts: Cygnus: Add BCM11360's V3D device
ARM: dts: BCM5301X: Specify MDIO bus in the DT
ARM: dts: BCM5301X: Add CPU thermal sensor and zone
ARM: dts: bcm283x: switch from &sdhci to &sdhost
ARM: dts: bcm283x: Add CPU thermal zone with 1 trip point
ARM: dts: Add devicetree for the Raspberry Pi 3, for arm32 (v6)
Signed-off-by: Olof Johansson <olof@lixom.net>
Olof Johansson [Mon, 19 Jun 2017 03:11:08 +0000 (20:11 -0700)]
Merge tag 'uniphier-dt-v4.13' of git://git./linux/kernel/git/masahiroy/linux-uniphier into next/dt
UniPhier ARM SoC DT updates for v4.13
- fix W=1 build warnings
- use SPDX License Identifier
- add generic compatible string for I2C EEPROM
* tag 'uniphier-dt-v4.13' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-uniphier:
ARM: dts: uniphier: Add generic compatible string for I2C EEPROM
ARM: dts: uniphier: use SPDX-License-Identifier
ARM: dts: uniphier: fix simple-bus unit address format error
ARM: dts: uniphier: Use - instead of @ for DT OPP entries
Signed-off-by: Olof Johansson <olof@lixom.net>
Olof Johansson [Mon, 19 Jun 2017 03:06:32 +0000 (20:06 -0700)]
Merge tag 'stm32-dt-for-v4.13-1' of git://git./linux/kernel/git/atorgue/stm32 into next/dt
STM32 DT updates for v4.13, round 1
Highlights:
----------
- Add stm32h743-disco board support
- Add stm32f746-disco board support
- Add stm32f769-disco board support
- Enable LTDC & simple pannel on stm32f429-eval
- Enable Watchdog on stm32f429-eval
- Enable DCMI on stm32f429-eval
- Enable STMPE1600 io expander on stm32f429-eval
- Enable OV2640 camera on stm32f429-eval
- Enable CRC on stm32f429-eval & stm32f429-disco
* tag 'stm32-dt-for-v4.13-1' of git://git.kernel.org/pub/scm/linux/kernel/git/atorgue/stm32:
ARM: dts: stm32: Add stm32h743i-disco board
ARM: dts: stm32: Add usart2 support on stm32h743
ARM: dts: stm32: Add usart2_pins on stm32h743
ARM: dts: stm32: enable CRC32 on stm32429i-eval board
ARM: dts: stm32: enable CRC32 on stm32429-disco board
ARM: dts: stm32: Add CRC support to stm32f429
ARM: dts: stm32: Enable OV2640 camera support of STM32F429-EVAL board
ARM: dts: stm32: Enable STMPE1600 gpio expander of STM32F429-EVAL board
ARM: dts: stm32: Enable DCMI camera interface on STM32F429-EVAL board
ARM: dts: stm32: Enable DCMI support on STM32F429 MCU
ARM: dts: stm32: Add missing reset-cells node in stm32f746
ARM: dts: stm32: Set gpio controller as interrupt controller on F4 and F7
ARM: dts: stm32: Add watchdog support for STM32F429 eval board
ARM: dts: stm32: Add watchdog support for STM32F429 SoC
ARM: dts: stm32: Enable ltdc & simple panel on stm32f429-Eval board
ARM: dts: stm32: Add ltdc support on stm32f429 MCU
ARM: dts: stm32: add stm32f769I & stm32f746 discovery board support
Signed-off-by: Olof Johansson <olof@lixom.net>
Olof Johansson [Mon, 19 Jun 2017 02:22:03 +0000 (19:22 -0700)]
Merge tag 'v4.12-next-dts32' of https://github.com/mbgg/linux-mediatek into next/dt
Add device tree nodes for
mt7623:
- clocks
- power domain
- pmic-wrapper
- pinctrl
- i2c
- spi
- nand
- mmc
- usb
- pwm
- ethernet
- crypto engine
- infared remote control
- audio controller
- ADC
- efuse
- thermal driver
- HW random generator
mt2701:
- NOR flash
- JPEG decoder
- i2c
- audio controller
* tag 'v4.12-next-dts32' of https://github.com/mbgg/linux-mediatek: (25 commits)
arm: dts: mediatek: Add audio driver node for MT2701
arm: dts: Add Mediatek MT2701 i2c device node
arm: dts: mt2701: Add node for Mediatek JPEG Decoder
arm: dts: mt2701: add nor flash node
ARM: dts: mt2701: Add mtk-cirq node for mt2701
arm: dts: mt7623: add Sean as one of authors for mt7623.dtsi files
arm: dts: mt7623: add thermal nodes to the mt7623.dtsi file
arm: dts: mt7623: add efuse nodes to the mt7623.dtsi file
arm: dts: mt7623: add auxadc nodes to the mt7623.dtsi file
arm: dts: mt7623: add rng nodes to the mt7623.dtsi file
arm: dts: mt7623: add afe nodes to the mt7623.dtsi file
arm: dts: mt7623: add ir nodes to the mt7623.dtsi file
arm: dts: mt7623: add crypto engine nodes to the mt7623.dtsi file
arm: dts: mt7623: add ethernet nodes to the mt7623.dtsi file
arm: dts: mt7623: add pwm nodes to the mt7623.dtsi file
arm: dts: mt7623: add usb nodes to the mt7623.dtsi file
arm: dts: mt7623: add mmc nodes to the mt7623.dtsi file
arm: dts: mt7623: add nand nodes to the mt7623.dtsi file
arm: dts: mt7623: add spi nodes to the mt7623.dtsi file
arm: dts: mt7623: add i2c nodes to the mt7623.dtsi file
...
Signed-off-by: Olof Johansson <olof@lixom.net>
Olof Johansson [Mon, 19 Jun 2017 02:14:52 +0000 (19:14 -0700)]
Merge tag 'keystone_dts_for_4.13' of git://git./linux/kernel/git/ssantosh/linux-keystone into next/dt
ARM: dts: Keystone K2G ICE EVM support for v4.13
* tag 'keystone_dts_for_4.13' of git://git.kernel.org/pub/scm/linux/kernel/git/ssantosh/linux-keystone:
ARM: dts: keystone: Add minimum support for K2G ICE evm
ARM: keystone: Create new binding for K2G ICE evm
ARM: dts: k2g-evm: Add unit address to memory node
ARM: dts: keystone-k2g: Remove skeleton.dtsi
Signed-off-by: Olof Johansson <olof@lixom.net>
Olof Johansson [Mon, 19 Jun 2017 02:10:31 +0000 (19:10 -0700)]
Merge tag 'samsung-dt-4.13' of git://git./linux/kernel/git/krzk/linux into next/dt
Samsung DeviceTree update for v4.13:
1. Add HDMI CEC to Exynos5 SoCs.
2. Minor cleanups and readability improvements.
* tag 'samsung-dt-4.13' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux:
ARM: dts: exynos: Use human-friendly symbols for GIC interrupt properties
ARM: dts: exynos: Use human-friendly symbols for interrupt flags in board sources
ARM: dts: exynos: Add HDMI CEC device to Exynos5 SoC family
ARM: dts: exynos: Remove MFC reserved buffers
Signed-off-by: Olof Johansson <olof@lixom.net>
Olof Johansson [Mon, 19 Jun 2017 02:07:25 +0000 (19:07 -0700)]
Merge tag 'v4.13-rockchip-dts32-1' of git://git./linux/kernel/git/mmind/linux-rockchip into next/dt
A bunch of changes including mali gpu nodes for rk3288 boards
following (and including) the new Mali Midgard binding; a lot of
improvements for the rk3228/rk3229 socs (tsadc, operating points,
usb, clock-rates, pinctrl, watchdog); finalizing the rk1108->rv1108
rename and adc buttons for the rk3288 firefly boards.
* tag 'v4.13-rockchip-dts32-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
ARM: dts: rockchip: enable usb for rk3229 evb board
ARM: dts: rockchip: add usb nodes on rk322x
ARM: dts: rockchip: add adc button for Firefly
ARM: dts: rockchip: enable ARM Mali GPU on rk3288-veyron
ARM: dts: rockchip: enable ARM Mali GPU on rk3288-firefly
ARM: dts: rockchip: enable ARM Mali GPU on rk3288-rock2-som
ARM: dts: rockchip: add ARM Mali GPU node for rk3288
dt-bindings: gpu: add bindings for the ARM Mali Midgard GPU
ARM: dts: rockchip: set a sane frequence for tsadc on rk322x
ARM: dts: rockchip: add operating-points-v2 for cpu on rk322x
ARM: dts: rockchip: set default rates for core clocks on rk322x
ARM: dts: rockchip: add second uart2 pinctrl on rk322x
ARM: dts: rockchip: correct rk322x uart2 pinctrl
ARM: dts: rockchip: add watchdog device node on rk322x
clk: rockchip: add clock-ids for more rk3228 clocks
clk: rockchip: add ids for camera on rk3399
ARM: dts: rockchip: fix rk322x i2s1 pinctrl error
ARM: dts: rockchip: rename RK1108-evb to RV1108-evb
ARM: dts: rockchip: rename core dtsi from RK1108 to RV1108
ARM: dts: rockchip: Setup usb vbus-supply on rk3288-rock2
Signed-off-by: Olof Johansson <olof@lixom.net>
Olof Johansson [Mon, 19 Jun 2017 02:05:14 +0000 (19:05 -0700)]
Merge tag 'davinci-for-v4.13/dt' of git://git./linux/kernel/git/nsekhar/linux-davinci into next/dt
Miscellaneous DT support updates for DA850. Includes Lego mindstorms
EV3 battery support, DMA support for MUSB, and non-critical fixes to
GPIO nodes of DA850's GPIO controller and GPIO expander available on
DA850 EVM.
* tag 'davinci-for-v4.13/dt' of git://git.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci:
ARM: dts: da850-evm: fix tca6416 for use with GPIO hogs
ARM: dts: da850: Add interrupt-controller property to gpio node
ARM: dts: da850: Add CPPI 4.1 DMA to USB OTG controller
ARM: dts: da850-lego-ev3: Add node for LEGO MINDSTORMS EV3 Battery
Signed-off-by: Olof Johansson <olof@lixom.net>
Olof Johansson [Mon, 19 Jun 2017 01:56:35 +0000 (18:56 -0700)]
Merge tag 'omap-for-v4.13/dt-signed' of git://git./linux/kernel/git/tmlind/linux-omap into next/dt
Device tree changes for omaps for v4.13 merge window.
This adds support for am335x-boneblue. The rest of
the changes are for enabling features on various
devices with the git shortlog describing the changes.
* tag 'omap-for-v4.13/dt-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
arm: dts: am33xx: Remove redundant interrupt-parent property
ARM: dts: bonegreen-wireless: add WL1835 Bluetooth device node
ARM: dts: AM43XX: Remove min and max voltage values for dcdc3
ARM: dts: Add am335x-boneblue
ARM: dts: twl4030: Add missing madc reference for bci subnode
ARM: dts: am43xx-clocks: Add support for CLKOUT2
ARM: dts: Configure USB host for 37xx-evm
ARM: dts: omap: Add generic compatible string for I2C EEPROM
ARM: dts: Enable earlycon stdout path for LogicPD torpedo
ARM: dts: Enable earlycon stdout path for duovero
arm: dts: boneblack-wireless: add WL1835 Bluetooth device node
ARM: dts: am571x-idk: Enable the system mailboxes 5 and 6
ARM: dts: am572x-idk: Enable the system mailboxes 5 and 6
ARM: dts: omap4-devkit8000: fix gpmc ranges property
ARM: dts: omap3: Remove 'enable-active-low' property
ARM: dts: OMAP5: uevm: add µSD card detect
ARM: dts: omap4-droid4: Add bluetooth
ARM: dts: dra7x-evm: Enable dual-role mode for USB1
ARM: dts: Use - instead of @ for DT OPP entries for TI SoCs
ARM: dts: am335x-phycore-som: fix rv4162 compatible
Signed-off-by: Olof Johansson <olof@lixom.net>
Chen-Yu Tsai [Fri, 9 Jun 2017 16:05:49 +0000 (00:05 +0800)]
ARM: sun6i: a31s: primo81: Enable battery power supply
The MSI Primo81 tablet has a 3500 mAh 3.7V LiPo battery.
Enable the PMIC's battery power supply so the battery can be monitored.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Chen-Yu Tsai [Fri, 9 Jun 2017 16:05:48 +0000 (00:05 +0800)]
ARM: sun6i: a31s: primo81: Change USB OTG to OTG mode
Now that we have support for the AXP221 PMIC's USB VBUS detection and
DRIVEVBUS vbus control, we can use the USB OTG port in proper OTG mode.
This patch enables the aforementioned PMIC functions, adds the OTG ID
detection pin to the USB PHY node, and changes the mode of USB OTG to
"otg".
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Corentin Labbe [Wed, 7 Jun 2017 17:33:44 +0000 (19:33 +0200)]
ARM: sun8i: a83t: Add dt node for the syscon control module
This patch add the dt node for the syscon register present on the
Allwinner A83T
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Linus Walleij [Mon, 20 Mar 2017 22:39:26 +0000 (23:39 +0100)]
ARM: dts: add Gemini PATA/SATA support
The NAS4229B and SQ201 Gemini systems have a PATA controller
which is linked to a SATA bridge in the SoC. Enable both
platforms to use the PATA/SATA devices.
Cc: John Feng-Hsin Chiang <john453@faraday-tech.com>
Cc: Greentime Hu <green.hu@gmail.com>
Acked-by: Hans Ulli Kroll <ulli.kroll@googlemail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Linus Walleij [Sat, 1 Apr 2017 17:55:48 +0000 (19:55 +0200)]
ARM: dts: Add Gemini DMA controller
This adds the Faraday Technology FTDMAC020 DMA controller to
the Gemini SoC DTSI file. It is only used for memcpy work so
we can activate it for all users of the chipset.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Florian Fainelli [Tue, 13 Jun 2017 19:38:48 +0000 (12:38 -0700)]
Merge tag 'bcm2835-dt-next-2017-06-12' into devicetree/next
This pull request brings in installation of the RPi3 DT in 32-bit
mode, the new thermal nodes, switches to the faster sdhost controller
for MMC, and enables USB OTG mode on the Pi 0.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Stefan Wahren [Sun, 21 May 2017 16:44:38 +0000 (18:44 +0200)]
ARM: dts: bcm2835-rpi-zero: Enable OTG mode
Since
635c21068cf ("usb: dwc2: gadget: Fix WARN_ON messages
during FIFO init") the dwc2 driver is able to handle OTG and gadget
mode for bcm2835. So enable this feature for the Raspberry Pi Zero.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Stefan Wahren [Sun, 21 May 2017 16:44:37 +0000 (18:44 +0200)]
ARM: dts: bcm283x: Add generic USB PHY
In order to use dwc2 in OTG or gadget mode the USB PHY should be
specified. Since there is no bcm283x USB PHY driver use the generic
one.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Stefan Wahren [Sun, 21 May 2017 16:44:36 +0000 (18:44 +0200)]
ARM: dts: bcm283x: Add dtsi for OTG mode
The Raspberry Pi Zero also supports OTG mode. So provide a dtsi file
to configure the USB interface accordingly. The fifo sizes are optimized
for device endpoint 6 and 7 with the maximum of 768.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Eric Anholt [Fri, 28 Apr 2017 22:22:04 +0000 (15:22 -0700)]
ARM: dts: Cygnus: Add the ethernet switch and ethernet PHY
Cygnus has a single amac controller connected to the B53 switch with 2
PHYs. On the BCM911360_EP platform, those two PHYs are connected to the
external ethernet jacks.
Signed-off-by: Eric Anholt <eric@anholt.net>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Jon Mason [Fri, 28 Apr 2017 20:11:31 +0000 (16:11 -0400)]
ARM: dts: NSP: Add Thermal Support
Add thermal support via the ns-thermal driver and create a single
thermal zone for the entire SoC.
Signed-off-by: Jon Mason <jon.mason@broadcom.com>
Acked-by: Eduardo Valentin <edubezval@gmail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Eric Anholt [Tue, 18 Apr 2017 23:32:34 +0000 (16:32 -0700)]
ARM: dts: Cygnus: Add BCM11360's V3D device
This loads the VC4 driver on the 911360_entphn platform (with the
corresponding series sent to dri-devel), which is supported by master
of the Mesa tree.
Signed-off-by: Eric Anholt <eric@anholt.net>
Acked-by: Scott Branden <scott.branden@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Rafał Miłecki [Wed, 19 Apr 2017 21:54:25 +0000 (23:54 +0200)]
ARM: dts: BCM5301X: Specify MDIO bus in the DT
Northstar devices have MDIO bus that may contain various PHYs attached.
A common example is USB 3.0 PHY (that doesn't have an MDIO driver yet).
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Rafał Miłecki [Fri, 14 Apr 2017 21:42:28 +0000 (23:42 +0200)]
ARM: dts: BCM5301X: Add CPU thermal sensor and zone
This uses CPU thermal sensor available on every Northstar chipset to
monitor temperature. We don't have any cooling or throttling so only a
critical trip was added.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Acked-by: Jon Mason <jon.mason@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Martin Blumenstingl [Sun, 4 Jun 2017 18:33:41 +0000 (20:33 +0200)]
ARM: dts: meson8: add and use the real clock controller
This removes the dummy clk81 gate and replaces it with the actual clock
controller's CLKID_CLK81. This will also allow us to pass the real clock
IDs to all devices where the clock is controlled by clkc in the future.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Acked-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Javier Martinez Canillas [Tue, 23 May 2017 13:34:40 +0000 (15:34 +0200)]
ARM: dts: uniphier: Add generic compatible string for I2C EEPROM
The at24 driver allows to register I2C EEPROM chips using different vendor
and devices, but the I2C subsystem does not take the vendor into account
when matching using the I2C table since it only has device entries.
But when matching using an OF table, both the vendor and device has to be
taken into account so the driver defines only a set of compatible strings
using the "atmel" vendor as a generic fallback for compatible I2C devices.
So add this generic fallback to the device node compatible string to make
the device to match the driver using the OF device ID table.
Signed-off-by: Javier Martinez Canillas <javier@dowhile0.org>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Patrice Chotard [Wed, 7 Jun 2017 07:16:00 +0000 (09:16 +0200)]
ARM: dts: stm32: Add stm32h743i-disco board
Add basic support for stm32h743i-discovery board
This board offers :
_ 2MBytes Flash
_ 1 x micro USB OTG port
_ 1 x STLink connector (micro USB)
_ 1 x micro SD card slot
_ 1 x RJ45 connector
_ 1 x RCA connector
_ 2 x Audio jack connectors (in and out)
_ 2 x speaker connectors (left and right)
_ 1 x joystick
_ 1 x DCMI connector (Digital camera interface)
_ 1 x 4 inch DSI LCD (Display Serial Interface)
_ Arduino Uno Connectors
_ 2 x PIO connectors (PMOD and PMOD+)
_ 1 x wakeup button
_ 1 x reset button
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com>
Patrice Chotard [Wed, 7 Jun 2017 07:16:00 +0000 (09:16 +0200)]
ARM: dts: stm32: Add usart2 support on stm32h743
This usart is used for console output on stm32h743i-disco board
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com>
Patrice Chotard [Wed, 7 Jun 2017 07:16:00 +0000 (09:16 +0200)]
ARM: dts: stm32: Add usart2_pins on stm32h743
Add usart2 pins definition in order to add usart2 support
dedicated for console output on stm32h743i-disco board.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com>
Chen-Yu Tsai [Sat, 3 Jun 2017 14:44:27 +0000 (22:44 +0800)]
ARM: sun8i: a83t: Add device node for R_PIO
The A83T has 1 pingroup with 13 pins belonging to the R_PIO
or special pin controller.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Krzysztof Kozlowski [Fri, 2 Jun 2017 18:13:46 +0000 (20:13 +0200)]
ARM: dts: exynos: Use human-friendly symbols for GIC interrupt properties
Replace hard-coded values of type of GIC interrupt and its flags with
respective macros from header to increase code readability.
Suggested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Krzysztof Kozlowski [Fri, 2 Jun 2017 18:13:45 +0000 (20:13 +0200)]
ARM: dts: exynos: Use human-friendly symbols for interrupt flags in board sources
Replace hard-coded values of interrupt flags with respective macros from
header to increase code readability.
Suggested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Cosar Dindar [Mon, 22 May 2017 14:35:00 +0000 (16:35 +0200)]
ARM: dts: stm32: enable CRC32 on stm32429i-eval board
Enable the CRC32 crypto on stm32429i-eval board.
Signed-off-by: Cosar Dindar <cosardindar@gmail.com>
Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com>
Cosar Dindar [Mon, 22 May 2017 14:34:00 +0000 (16:34 +0200)]
ARM: dts: stm32: enable CRC32 on stm32429-disco board
Enable the CRC32 crypto on stm32429-disco board.
Signed-off-by: Cosar Dindar <cosardindar@gmail.com>
Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com>
Cosar Dindar [Mon, 22 May 2017 14:34:00 +0000 (16:34 +0200)]
ARM: dts: stm32: Add CRC support to stm32f429
Add CRC32 Crypto support to stm32f429.
Signed-off-by: Cosar Dindar <cosardindar@gmail.com>
Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com>
Hugues Fruchet [Fri, 5 May 2017 15:31:00 +0000 (17:31 +0200)]
ARM: dts: stm32: Enable OV2640 camera support of STM32F429-EVAL board
Enable OV2640 camera support of STM32F429-EVAL board.
Signed-off-by: Hugues Fruchet <hugues.fruchet@st.com>
Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com>
Hugues Fruchet [Wed, 7 Jun 2017 15:39:11 +0000 (17:39 +0200)]
ARM: dts: stm32: Enable STMPE1600 gpio expander of STM32F429-EVAL board
Enable STMPE1600 gpio expander of STM32F429-EVAL board.
Signed-off-by: Hugues Fruchet <hugues.fruchet@st.com>
Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com>
Hugues Fruchet [Fri, 5 May 2017 15:31:00 +0000 (17:31 +0200)]
ARM: dts: stm32: Enable DCMI camera interface on STM32F429-EVAL board
Enable DCMI camera interface on STM32F429-EVAL board.
Signed-off-by: Hugues Fruchet <hugues.fruchet@st.com>
Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com>
Hugues Fruchet [Fri, 5 May 2017 15:31:00 +0000 (17:31 +0200)]
ARM: dts: stm32: Enable DCMI support on STM32F429 MCU
Enable DCMI camera interface on STM32F429 MCU.
Signed-off-by: Hugues Fruchet <hugues.fruchet@st.com>
Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com>
Lionel Debieve [Wed, 7 Jun 2017 14:50:21 +0000 (16:50 +0200)]
ARM: dts: stm32: Add missing reset-cells node in stm32f746
rcc node must include reset-cells node.
Signed-off-by: Lionel Debieve <lionel.debieve@st.com>
Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com>
Alexandre TORGUE [Wed, 7 Jun 2017 14:41:36 +0000 (16:41 +0200)]
ARM: dts: stm32: Set gpio controller as interrupt controller on F4 and F7
This patch set each gpio controller as a interrupt controller. User who
wants to use gpio as interrupt will have choice to use either "gpiolib"
interface or "common" interrupt interface.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com>
Yannick Fertre [Wed, 7 Jun 2017 13:39:40 +0000 (15:39 +0200)]
ARM: dts: stm32: Add watchdog support for STM32F429 eval board
This patch adds watchdog support for STM32x9I-Eval board.
Signed-off-by: Yannick Fertre <yannick.fertre@st.com>
Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com>
Yannick Fertre [Thu, 6 Apr 2017 12:19:00 +0000 (14:19 +0200)]
ARM: dts: stm32: Add watchdog support for STM32F429 SoC
Add watchdog into DT for stm32f429 family.
Signed-off-by: Yannick FERTRE <yannick.fertre@st.com>
Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com>
Icenowy Zheng [Wed, 24 May 2017 11:17:23 +0000 (19:17 +0800)]
ARM: sun8i: v3s: add device nodes for DE2 display pipeline
Allwinner V3s SoC features a "Display Engine 2.0" with only one mixer
and only one TCON connected to this mixer, which have RGB LCD output.
Add device nodes for this display pipeline.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Antoine Tenart [Thu, 1 Jun 2017 19:39:05 +0000 (21:39 +0200)]
ARM: dts: sunxi: add SoC specific compatibles for the crypto nodes
Add SoC specific compatibles for all sunXi crypto nodes, in addition to
the one already used (allwinner,sun4i-a10-crypto).
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Antoine Tenart [Thu, 1 Jun 2017 19:39:04 +0000 (21:39 +0200)]
ARM: sun5i: add a cryptographic engine node
Add a node for the cryptographic engine that can be found on sun5i SoCs.
This cryptographic engine is compatible with the Allwinner cryptographic
accelerator driver.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Yannick Fertre [Wed, 7 Jun 2017 13:20:53 +0000 (15:20 +0200)]
ARM: dts: stm32: Enable ltdc & simple panel on stm32f429-Eval board
Enable ltdc & enable am-480272h3tmqw-t01h panel.
Signed-off-by: Yannick Fertre <yannick.fertre@st.com>
Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com>
Yannick Fertre [Wed, 7 Jun 2017 12:58:10 +0000 (14:58 +0200)]
ARM: dts: stm32: Add ltdc support on stm32f429 MCU
Add LTDC (Lcd-tft Display Controller) support.
Signed-off-by: Yannick Fertre <yannick.fertre@st.com>
Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com>
Vikas Manocha [Wed, 7 Jun 2017 11:55:25 +0000 (13:55 +0200)]
ARM: dts: stm32: add stm32f769I & stm32f746 discovery board support
Stm32f769I & stm32f746 are MCUs of stm32f7 family. Here are the major
specs of the two boards:
stm32f769I discovery board:
- Cortex-M7 core @216MHz
- 2MB mcu internal flash
- 512KB internal sram
- 16MB sdram memory
- 64MB qspi flash memory
- 4 inch wvga LCD-TFT Display
stm32f746 discovery board:
- Cortex-M7 core @216MHz
- 1MB mcu internal flash
- 320KB internal sram
- 8MB sdram memory
- 16MB qspi flash memory
- 4.3 inch 480x272 LCD-TFT display
Signed-off-by: Vikas Manocha <vikas.manocha@st.com>
Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com>
Garlic Tseng [Thu, 1 Jun 2017 05:42:10 +0000 (13:42 +0800)]
arm: dts: mediatek: Add audio driver node for MT2701
Add audio driver node for mt2701
Signed-off-by: Garlic Tseng <garlic.tseng@mediatek.com>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Kevin Hilman [Wed, 31 May 2017 01:21:25 +0000 (18:21 -0700)]
ARM: dts: da850-evm: fix tca6416 for use with GPIO hogs
In order GPIOS from this controller to be used with the "gpio-hogs"
property, the tca6416 node has to properly labeled as a gpio-controller,
and use #gpio-cells.
With that, the SEL_A, SEL_B, SEL_C lines that are used to select VPIF
input can be configured using GPIO hogs.
As an example, example, the configuration below selects the analog video
input on the da850-evm UI board:
&tca6416 {
status = "okay";
sel_a {
gpio-hog;
gpios = <7 GPIO_ACTIVE_HIGH>;
output-high;
line-name = "ADC_ENn";
};
sel_b {
gpio-hog;
gpios = <6 GPIO_ACTIVE_HIGH>;
output-high;
line-name = "CAMERA_ENn";
};
sel_c {
gpio-hog;
gpios = <5 GPIO_ACTIVE_HIGH>;
output-low;
line-name = "VIDEO_IN_ENn";
};
};
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Suniel Mahesh [Mon, 5 Jun 2017 18:17:16 +0000 (23:47 +0530)]
arm: dts: am33xx: Remove redundant interrupt-parent property
Interrupt-parent property is defined in the root node as
"interrupt-parent = <&intc>". This interrupt-parent value becomes
the default for the system, so removed redundant "interrupt-parent"
property from mmc, mac, lcdc and tscadc nodes.
Signed-off-by: Suniel Mahesh <sunil.m@techveda.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Robert Nelson [Mon, 5 Jun 2017 15:36:21 +0000 (10:36 -0500)]
ARM: dts: bonegreen-wireless: add WL1835 Bluetooth device node
This adds the serial slave device for the WL1835 Bluetooth interface.
Signed-off-by: Robert Nelson <robertcnelson@gmail.com>
CC: Ricardo Salveti <ricardo.salveti@linaro.org>
CC: Tony Lindgren <tony@atomide.com>
CC: Jason Kridner <jkridner@beagleboard.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Keerthy [Fri, 2 Jun 2017 09:24:01 +0000 (14:54 +0530)]
ARM: dts: AM43XX: Remove min and max voltage values for dcdc3
dcdc3 supplies to DDR on AM43x series. When we set both
min and max values to the same value. The regulator framework
sets that particular voltage. This is bad as we are changing
the ddr voltage when executing from ddr. Hence remove the min and
max values. The ddr supply voltage shall be set from bootloader
when not executing from ddr and not while executing from kernel.
The previous discussion can be found here:
http://www.spinics.net/lists/devicetree/msg56399.html
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Robert Nelson [Tue, 30 May 2017 16:20:23 +0000 (11:20 -0500)]
ARM: dts: Add am335x-boneblue
BeagleBone Blue is robotics-oriented version of the BeagleBone Black (BBB).
This board can be indentified by the BLAx value after A335BNLT (BBB)
in the at24 eeprom:
BLAx [aa 55 33 ee 41 33 33 35 42 4e 4c 54 42 4c 41 30 |.U3.A335BNLTBLA2|]
http://beagleboard.org/blue
https://github.com/beagleboard/beaglebone-blue
firmware: https://github.com/beagleboard/beaglebone-black-wireless/tree/master/firmware
wl18xx mac address: /proc/device-tree/ocp/ethernet@
4a100000/slave@
4a100200/mac-address
Signed-off-by: Robert Nelson <robertcnelson@gmail.com>
CC: Jason Kridner <jkridner@beagleboard.org>
CC: Drew Fustini <drew@beagleboard.org>
Acked-by: Jason Kridner <jkridner@beagleboard.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Marek Belisko [Sun, 21 May 2017 10:38:17 +0000 (12:38 +0200)]
ARM: dts: twl4030: Add missing madc reference for bci subnode
The twl4030_charger driver expects an iio channel to detect the
presence of an AC charger by looking at VAC (madc channel 11).
This definition is missing in the device tree.
Signed-off-by: Marek Belisko <marek@goldelico.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Masahiro Yamada [Mon, 5 Jun 2017 03:57:58 +0000 (12:57 +0900)]
ARM: dts: uniphier: use SPDX-License-Identifier
Follow the recent trend for the license description, and fix the wrongly
stated X11 to MIT.
The X11 license text [1] is explicitly for the X Consortium and has a
couple of extra clauses. The MIT license text [2] is actually what the
current DT files claim.
[1] https://spdx.org/licenses/X11.html
[2] https://spdx.org/licenses/MIT.html
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Masahiro Yamada [Sat, 13 May 2017 17:20:49 +0000 (02:20 +0900)]
ARM: dts: uniphier: fix simple-bus unit address format error
Compiling the UniPhier DT files with W=1, DTC warns like follows:
Warning (simple_bus_reg): Node /soc/system-bus@
58c00000/support_card@1,
1f00000/ethernet@
00000000 simple-bus unit address format error, expected "0"
Warning (simple_bus_reg): Node /soc/system-bus@
58c00000/support_card@1,
1f00000/uart@
000b0000 simple-bus unit address format error, expected "b0000"
Warning (simple_bus_reg): Node /soc/smpctrl@
59800000 simple-bus unit address format error, expected "
59801000"
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Viresh Kumar [Thu, 20 Apr 2017 10:55:10 +0000 (16:25 +0530)]
ARM: dts: uniphier: Use - instead of @ for DT OPP entries
Compiling the DT file with W=1, DTC warns like follows:
Warning (unit_address_vs_reg): Node /opp_table0/opp@
1000000000 has a
unit name, but no reg property
Fix this by replacing '@' with '-' as the OPP nodes will never have a
"reg" property.
Reported-by: Krzysztof Kozlowski <krzk@kernel.org>
Reported-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Suggested-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Chen-Yu Tsai [Wed, 31 May 2017 07:58:20 +0000 (15:58 +0800)]
ARM: sun8i: a83t: Add device node for PRCM
The A83T's PRCM has the same set of clocks and resets as the A64.
However, a few dividers are different. And due to the lack of a low
speed 32.768 kHz oscillator, a few of the clock parents are different.
The PRCM also has controls for various power domains. These are not
supported yet, neither in software nor in the device tree binding.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Marek Szyprowski [Wed, 31 May 2017 11:00:17 +0000 (13:00 +0200)]
ARM: dts: exynos: Add HDMI CEC device to Exynos5 SoC family
Exynos5250 and Exynos542x SoCs have the same CEC hardware module as
Exynos4 SoC series, so enable support for it using the same compatible
string.
Tested on Odroid XU3 (Exynos5422) and Google Snow (Exynos5250) boards.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
William Wu [Fri, 2 Jun 2017 07:04:25 +0000 (15:04 +0800)]
ARM: dts: rockchip: enable usb for rk3229 evb board
Rockchip's rk3229 evaluation board has one usb otg controller
and three usb host controllers. Each usb controller connect
with one usb2 phy port through UTMI+ interface. And the three
usb host interfaces use the same GPIO VBUS drive. Let's enable
them to support usb on rk3229 evb board.
Signed-off-by: William Wu <william.wu@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
William Wu [Fri, 2 Jun 2017 07:04:24 +0000 (15:04 +0800)]
ARM: dts: rockchip: add usb nodes on rk322x
This patch adds usb otg/host controllers and phys nodes on rk322x.
Signed-off-by: William Wu <william.wu@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Linus Walleij [Wed, 24 May 2017 09:07:48 +0000 (11:07 +0200)]
ARM: dts: augment Moxa and Aspeed DTS for FTTMR010
This augments the Moxa Art and Aspeed device trees to:
- Explicitly name the clock "PCLK" as the Faraday FTTMR010
names it.
- List the Moxa timer as compatible with the Faradat FTTMR010
vanilla version.
- Add a comment that the Aspeed driver is a Faraday
FTTMR010 derivative.
- Pass all IRQs to the timer from Aspeed: they are all there
so they should be in the device tree, we only use the
first one anyways.
Tested-by: Joel Stanley <joel@jms.id.au>
Tested-by: Jonas Jensen <jonas.jensen@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
Olof Johansson [Fri, 2 Jun 2017 00:26:06 +0000 (17:26 -0700)]
Merge tag 'gemini-v4.13-dts-1' of git://git./linux/kernel/git/linusw/linux-nomadik into next/dt
This is a first set of Gemini DTS patches for the v4.13 cycle.
This adds the reset and clock lines to the Gemini core DTS SoC.
These bindings have been ACKed by the DT maintainer Rob.
The reset driver is going to be merged by the reset maintainer.
The clock driver is going to be merged by the clock maintainers.
Each of these have their macro defines coming with them, split
off as separate patches.
A post-rc1 patch will be sumbitted for switching the numerical
values to the defined macros in line with the ARM SoC DT header
merge strategy.
* tag 'gemini-v4.13-dts-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-nomadik:
ARM: dts: Add clocks to the Gemini SoC
ARM: dts: Add the Gemini reset controller
dt-bindings: Augment Gemini for clocks, resets
Signed-off-by: Olof Johansson <olof@lixom.net>
Olof Johansson [Fri, 2 Jun 2017 00:24:15 +0000 (17:24 -0700)]
Merge tag 'renesas-dt-for-v4.13' of https://git./linux/kernel/git/horms/renesas into next/dt
Renesas ARM Based SoC DT Updates for v4.13
* Switch to panel-lvds bindings for Mitsubishi panels
* Clean up PFC node names
* Enable UHS-I SDR-50 and SDR-104 on r8a7793/Gose
* Add GyroADC clock and device for r8a7791 SoC
* Add USB clocks to device tree for r7s72100 SoC
* tag 'renesas-dt-for-v4.13' of https://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
ARM: dts: renesas: Switch to panel-lvds bindings for Mitsubishi panels
ARM: dts: gose: Enable UHS-I SDR-50 and SDR-104
ARM: dts: r8a7793: set maximum frequency for SDHI clocks
ARM: dts: r8a7791: Add GyroADC clock and device node
ARM: dts: r7s72100: add usb clocks to device tree
ARM: dts: sh73a0: update PFC node name to pin-controller
ARM: dts: r8a7793: update PFC node name to pin-controller
ARM: dts: r8a7791: update PFC node name to pin-controller
ARM: dts: r8a7790: update PFC node name to pin-controller
ARM: dts: r8a7779: update PFC node name to pin-controller
ARM: dts: r8a7778: update PFC node name to pin-controller
ARM: dts: r8a7740: update PFC node name to pin-controller
ARM: dts: r8a73a4: update PFC node name to pin-controller
ARM: dts: emev2: update PFC node name to pin-controller
ARM: dts: r7s72100: add USB bit definitions
ARM: dts: r7s72100: add Renesas RZ/A1 pinctrl header
ARM: dts: r8a7791: add GyroADC clock
Signed-off-by: Olof Johansson <olof@lixom.net>
Randy Li [Tue, 30 May 2017 15:52:46 +0000 (23:52 +0800)]
ARM: dts: rockchip: add adc button for Firefly
The only adc button connected to adc input is recovery button.
Signed-off-by: Randy Li <ayaka@soulik.info>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Jagan Teki [Tue, 30 May 2017 17:42:50 +0000 (17:42 +0000)]
ARM: dts: sun8i: h3: Add initial NanoPi M1 Plus support
NanoPi M1 Plus is designed and developed by FriendlyElec
for professionals, enterprise users, makers and hobbyists
using the Allwinner H3 SOC.
NanoPi M1 Plus key features
- Allwinner H3, Quad-core Cortex-A7@1.2GHz
- 1GB DDR3 RAM
- 8GB eMMC
- microSD slot
- 10/100/1000M Ethernet
- Serial Debug Port
- 5V 2A DC power-supply
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Peter Ujfalusi [Wed, 24 May 2017 08:43:41 +0000 (11:43 +0300)]
ARM: dts: am43xx-clocks: Add support for CLKOUT2
Add the needed clock nodes for the CLKOUT2 to be usable by boards.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Jun Gao [Fri, 26 May 2017 07:35:07 +0000 (15:35 +0800)]
arm: dts: Add Mediatek MT2701 i2c device node
Add MT2701 i2c device node.
Signed-off-by: Jun Gao <jun.gao@mediatek.com>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Rick Chang [Wed, 14 Dec 2016 08:04:49 +0000 (16:04 +0800)]
arm: dts: mt2701: Add node for Mediatek JPEG Decoder
Signed-off-by: Rick Chang <rick.chang@mediatek.com>
Signed-off-by: Minghsiu Tsai <minghsiu.tsai@mediatek.com>
[mb: include mt2701-larb-port.h to fix build errors]
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Keerthy [Wed, 24 May 2017 14:01:41 +0000 (19:31 +0530)]
ARM: dts: da850: Add interrupt-controller property to gpio node
The gpio node has 144 gpios. Each gpio is capable of generating
an interrupt. Hence add interrupt-controller property to the gpio
node. With this in place one can use interrupts property in device
tree to request for the gpio interrupts.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Alexandre Bailon [Fri, 19 May 2017 13:33:36 +0000 (15:33 +0200)]
ARM: dts: da850: Add CPPI 4.1 DMA to USB OTG controller
This adds CPPI 4.1 DMA controller to USB OTG controller.
Changes since v2:
- Fixed the the property reg-names (had glue register defined)
- Removed few useless property
Signed-off-by: Alexandre Bailon <abailon@baylibre.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Sergey Matyukevich [Sun, 28 May 2017 10:30:26 +0000 (13:30 +0300)]
ARM: dts: orange-pi-zero: add node for SPI NOR
Add node for SPI NOR flash on orange-pi-zero board. Disable this node
by default and leave it to users to enable it if their board has
SPI NOR flash chip populated.
SPI NOR flash was optional in the first production batch in Dec 2016.
In later batches flash chip was pre-populated. However there should
be quite a few boards around which do not have flash chip.
Signed-off-by: Sergey Matyukevich <geomatsi@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Chen-Yu Tsai [Thu, 25 May 2017 07:31:38 +0000 (15:31 +0800)]
ARM: sun7i: a20: cubietruck: Tie AXP209's USB power supply to USB PHY
The USB PHY can use either a GPIO pin or the PMIC's USB power supply
to sense VBUS. Since both options are available on the Cubietruck,
add the missing property for the USB power supply to the USB PHY node.
The device tree provides all usable options. Ultimately, which method
is used is up to the driver implementation.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Chen-Yu Tsai [Thu, 25 May 2017 07:31:37 +0000 (15:31 +0800)]
ARM: sun6i: a31: hummingbird: Enable AXP221's ACIN power supply
The ACIN pins of the AXP221 PMIC on the A31 Hummingbird are tied to the
DC jack on the board through a 12V to 5V buck converter.
Enable the ACIN power supply.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Chen-Yu Tsai [Thu, 25 May 2017 07:31:36 +0000 (15:31 +0800)]
ARM: sun4i: a10: cubieboard: Enable AXP209's ACIN power supply
The ACIN pins of the AXP209 PMIC on the Cubieboard are tied to the
DC jack on the board.
Enable the ACIN power supply.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Chen-Yu Tsai [Thu, 25 May 2017 07:31:35 +0000 (15:31 +0800)]
ARM: sun7i: a20: bananapi-m1-plus: Enable AXP209's ACIN power supply
The ACIN pins of the AXP209 PMIC on the Bananapi M1 Plus are tied to the
"power input" micro USB connector next to the SATA connector on the board.
Enable the ACIN power supply.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Chen-Yu Tsai [Thu, 25 May 2017 07:31:34 +0000 (15:31 +0800)]
ARM: sun7i: a20: cubieboard2: Enable AXP209's ACIN power supply
The ACIN pins of the AXP209 PMIC on the Cubieboard 2 are tied to the
DC jack on the board.
Enable the ACIN power supply.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Chen-Yu Tsai [Thu, 25 May 2017 07:31:33 +0000 (15:31 +0800)]
ARM: sun7i: a20: cubieboard2: Move usb_otg node for alphabetical ordering
We want to keep node references in alphabetical order, except for
instances where node must be #included first.
Move the usb_otg node reference so that all references to non-AXP209
device nodes are in alphabetical order.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Linus Torvalds [Mon, 29 May 2017 00:20:53 +0000 (17:20 -0700)]
Linux 4.12-rc3
Linus Torvalds [Sun, 28 May 2017 23:18:27 +0000 (16:18 -0700)]
Merge branch 'fixes' of git://git./linux/kernel/git/evalenti/linux-soc-thermal
Pull thermal SoC management fixes from Eduardo Valentin:
- fixes to TI SoC driver, Broadcom, qoriq
- small sparse warning fix on thermal core
* 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/evalenti/linux-soc-thermal:
thermal: broadcom: ns-thermal: default on iProc SoCs
ti-soc-thermal: Fix a typo in a comment line
ti-soc-thermal: Delete error messages for failed memory allocations in ti_bandgap_build()
ti-soc-thermal: Use devm_kcalloc() in ti_bandgap_build()
thermal: core: make thermal_emergency_poweroff static
thermal: qoriq: remove useless call for of_thermal_get_trip_points()
Linus Torvalds [Sat, 27 May 2017 16:39:09 +0000 (09:39 -0700)]
Merge tag 'tty-4.12-rc3' of git://git./linux/kernel/git/gregkh/tty
Pull tty/serial fixes from Greg KH:
"Here are some serial and tty fixes for 4.12-rc3. They are a bit bigger
than normal, which is why I had them bake in linux-next for a few
weeks and didn't send them to you for -rc2.
They revert a few of the serdev patches from 4.12-rc1, and bring
things back to how they were in 4.11, to try to make things a bit more
stable there. Rob and Johan both agree that this is the way forward,
so this isn't people squabbling over semantics. Other than that, just
a few minor serial driver fixes that people have had problems with.
All of these have been in linux-next for a few weeks with no reported
issues"
* tag 'tty-4.12-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
serial: altera_uart: call iounmap() at driver remove
serial: imx: ensure UCR3 and UFCR are setup correctly
MAINTAINERS/serial: Change maintainer of jsm driver
serial: enable serdev support
tty/serdev: add serdev registration interface
serdev: Restore serdev_device_write_buf for atomic context
serial: core: fix crash in uart_suspend_port
tty: fix port buffer locking
tty: ehv_bytechan: clean up init error handling
serial: ifx6x60: fix use-after-free on module unload
serial: altera_jtaguart: adding iounmap()
serial: exar: Fix stuck MSIs
serial: efm32: Fix parity management in 'efm32_uart_console_get_options()'
serdev: fix tty-port client deregistration
Revert "tty_port: register tty ports with serdev bus"
drivers/tty: 8250: only call fintek_8250_probe when doing port I/O
Linus Torvalds [Sat, 27 May 2017 16:28:34 +0000 (09:28 -0700)]
Merge tag 'powerpc-4.12-4' of git://git./linux/kernel/git/powerpc/linux
Pull powerpc fixes from Michael Ellerman:
"Fix running SPU programs on Cell, and a few other minor fixes.
Thanks to Alistair Popple, Jeremy Kerr, Michael Neuling, Nicholas
Piggin"
* tag 'powerpc-4.12-4' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
powerpc: Add PPC_FEATURE userspace bits for SCV and DARN instructions
powerpc/spufs: Fix hash faults for kernel regions
powerpc: Fix booting P9 hash with CONFIG_PPC_RADIX_MMU=N
powerpc/powernv/npu-dma.c: Fix opal_npu_destroy_context() call
selftests/powerpc: Fix TM resched DSCR test with some compilers
Linus Torvalds [Sat, 27 May 2017 16:17:58 +0000 (09:17 -0700)]
Merge branch 'x86-urgent-for-linus' of git://git./linux/kernel/git/tip/tip
Pull x86 fixes from Thomas Gleixner:
"A series of fixes for X86:
- The final fix for the end-of-stack issue in the unwinder
- Handle non PAT systems gracefully
- Prevent access to uninitiliazed memory
- Move early delay calaibration after basic init
- Fix Kconfig help text
- Fix a cross compile issue
- Unbreak older make versions"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/timers: Move simple_udelay_calibration past init_hypervisor_platform
x86/alternatives: Prevent uninitialized stack byte read in apply_alternatives()
x86/PAT: Fix Xorg regression on CPUs that don't support PAT
x86/watchdog: Fix Kconfig help text file path reference to lockup watchdog documentation
x86/build: Permit building with old make versions
x86/unwind: Add end-of-stack check for ftrace handlers
Revert "x86/entry: Fix the end of the stack for newly forked tasks"
x86/boot: Use CROSS_COMPILE prefix for readelf
Linus Torvalds [Sat, 27 May 2017 16:14:24 +0000 (09:14 -0700)]
Merge branch 'timers-urgent-for-linus' of git://git./linux/kernel/git/tip/tip
Pull timer fixlet from Thomas Gleixner:
"Silence dmesg spam by making the posix cpu timer printks depend on
print_fatal_signals"
* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
posix-timers: Make signal printks conditional
Linus Torvalds [Sat, 27 May 2017 16:06:43 +0000 (09:06 -0700)]
Merge branch 'ras-urgent-for-linus' of git://git./linux/kernel/git/tip/tip
Pull RAS fixes from Thomas Gleixner:
"Two fixlets for RAS:
- Export memory_error() so the NFIT module can utilize it
- Handle memory errors in NFIT correctly"
* 'ras-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
acpi, nfit: Fix the memory error check in nfit_handle_mce()
x86/MCE: Export memory_error()
Linus Torvalds [Sat, 27 May 2017 16:02:41 +0000 (09:02 -0700)]
Merge branch 'perf-urgent-for-linus' of git://git./linux/kernel/git/tip/tip
Pull perf tooling fixes from Thomas Gleixner:
- Synchronization of tools and kernel headers
- A series of fixes for perf report addressing various failures:
* Handle invalid maps proper
* Plug a memory leak
* Handle frames and callchain order correctly
- Fixes for handling inlines and children mode
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
tools/include: Sync kernel ABI headers with tooling headers
perf tools: Put caller above callee in --children mode
perf report: Do not drop last inlined frame
perf report: Always honor callchain order for inlined nodes
perf script: Add --inline option for debugging
perf report: Fix off-by-one for non-activation frames
perf report: Fix memory leak in addr2line when called by addr2inlines
perf report: Don't crash on invalid maps in `-g srcline` mode
Linus Torvalds [Sat, 27 May 2017 15:59:37 +0000 (08:59 -0700)]
Merge branch 'locking-urgent-for-linus' of git://git./linux/kernel/git/tip/tip
Pull locking fix from Thomas Gleixner:
"A fix for a state leak which was introduced in the recent rework of
futex/rtmutex interaction"
* 'locking-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
futex,rt_mutex: Fix rt_mutex_cleanup_proxy_lock()
Linus Torvalds [Sat, 27 May 2017 15:52:27 +0000 (08:52 -0700)]
Merge branch 'core-urgent-for-linus' of git://git./linux/kernel/git/tip/tip
Pull kthread fix from Thomas Gleixner:
"A single fix which prevents a use after free when kthread fork fails"
* 'core-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
kthread: Fix use-after-free if kthread fork fails
Linus Torvalds [Sat, 27 May 2017 15:30:30 +0000 (08:30 -0700)]
Merge tag 'trace-v4.12-rc2' of git://git./linux/kernel/git/rostedt/linux-trace
Pull ftrace fixes from Steven Rostedt:
"There's been a few memory issues found with ftrace.
One was simply a memory leak where not all was being freed that should
have been in releasing a file pointer on set_graph_function.
Then Thomas found that the ftrace trampolines were marked for
read/write as well as execute. To shrink the possible attack surface,
he added calls to set them to ro. Which also uncovered some other
issues with freeing module allocated memory that had its permissions
changed.
Kprobes had a similar issue which is fixed and a selftest was added to
trigger that issue again"
* tag 'trace-v4.12-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
x86/ftrace: Make sure that ftrace trampolines are not RWX
x86/mm/ftrace: Do not bug in early boot on irqs_disabled in cpu_flush_range()
selftests/ftrace: Add a testcase for many kprobe events
kprobes/x86: Fix to set RWX bits correctly before releasing trampoline
ftrace: Fix memory leak in ftrace_graph_release()
Thomas Gleixner [Thu, 25 May 2017 08:57:51 +0000 (10:57 +0200)]
x86/ftrace: Make sure that ftrace trampolines are not RWX
ftrace use module_alloc() to allocate trampoline pages. The mapping of
module_alloc() is RWX, which makes sense as the memory is written to right
after allocation. But nothing makes these pages RO after writing to them.
Add proper set_memory_rw/ro() calls to protect the trampolines after
modification.
Link: http://lkml.kernel.org/r/alpine.DEB.2.20.1705251056410.1862@nanos
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Steven Rostedt (VMware) [Fri, 26 May 2017 14:14:11 +0000 (10:14 -0400)]
x86/mm/ftrace: Do not bug in early boot on irqs_disabled in cpu_flush_range()
With function tracing starting in early bootup and having its trampoline
pages being read only, a bug triggered with the following:
kernel BUG at arch/x86/mm/pageattr.c:189!
invalid opcode: 0000 [#1] SMP
Modules linked in:
CPU: 0 PID: 0 Comm: swapper Not tainted 4.12.0-rc2-test+ #3
Hardware name: MSI MS-7823/CSM-H87M-G43 (MS-7823), BIOS V1.6 02/22/2014
task:
ffffffffb4222500 task.stack:
ffffffffb4200000
RIP: 0010:change_page_attr_set_clr+0x269/0x302
RSP: 0000:
ffffffffb4203c88 EFLAGS:
00010046
RAX:
0000000000000046 RBX:
0000000000000000 RCX:
00000001b6000000
RDX:
ffffffffb4203d40 RSI:
0000000000000000 RDI:
ffffffffb4240d60
RBP:
ffffffffb4203d18 R08:
00000001b6000000 R09:
0000000000000001
R10:
ffffffffb4203aa8 R11:
0000000000000003 R12:
ffffffffc029b000
R13:
ffffffffb4203d40 R14:
0000000000000001 R15:
0000000000000000
FS:
0000000000000000(0000) GS:
ffff9a639ea00000(0000) knlGS:
0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0:
0000000080050033
CR2:
ffff9a636b384000 CR3:
00000001ea21d000 CR4:
00000000000406b0
Call Trace:
change_page_attr_clear+0x1f/0x21
set_memory_ro+0x1e/0x20
arch_ftrace_update_trampoline+0x207/0x21c
? ftrace_caller+0x64/0x64
? 0xffffffffc029b000
ftrace_startup+0xf4/0x198
register_ftrace_function+0x26/0x3c
function_trace_init+0x5e/0x73
tracer_init+0x1e/0x23
tracing_set_tracer+0x127/0x15a
register_tracer+0x19b/0x1bc
init_function_trace+0x90/0x92
early_trace_init+0x236/0x2b3
start_kernel+0x200/0x3f5
x86_64_start_reservations+0x29/0x2b
x86_64_start_kernel+0x17c/0x18f
secondary_startup_64+0x9f/0x9f
? secondary_startup_64+0x9f/0x9f
Interrupts should not be enabled at this early in the boot process. It is
also fine to leave interrupts enabled during this time as there's only one
CPU running, and on_each_cpu() means to only run on the current CPU.
If early_boot_irqs_disabled is set, it is safe to run cpu_flush_range() with
interrupts disabled. Don't trigger a BUG_ON() in that case.
Link: http://lkml.kernel.org/r/20170526093717.0be3b849@gandalf.local.home
Suggested-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Masami Hiramatsu [Fri, 26 May 2017 04:44:54 +0000 (13:44 +0900)]
selftests/ftrace: Add a testcase for many kprobe events
Add a testcase to test kprobes via ftrace interface
with many concurrent kprobe events.
This tries to add many kprobe events (up to 256) on
kernel functions. To avoid making ftrace-based
kprobes (kprobes on fentry), it skips first N bytes
(on x86 N=5, on ppc or arm N=4) of function entry.
After that, it enables all those events, disable it,
and remove it.
Since the unoptimization buffer reclaiming will
be delayed, after removing events, it will wait
enough time.
Link: http://lkml.kernel.org/r/149577388470.11702.11832460851769204511.stgit@devbox
Signed-off-by: Masami Hiramatsu <mhiramat@kernel.org>
Suggested-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Masami Hiramatsu [Thu, 25 May 2017 10:38:17 +0000 (19:38 +0900)]
kprobes/x86: Fix to set RWX bits correctly before releasing trampoline
Fix kprobes to set(recover) RWX bits correctly on trampoline
buffer before releasing it. Releasing readonly page to
module_memfree() crash the kernel.
Without this fix, if kprobes user register a bunch of kprobes
in function body (since kprobes on function entry usually
use ftrace) and unregister it, kernel hits a BUG and crash.
Link: http://lkml.kernel.org/r/149570868652.3518.14120169373590420503.stgit@devbox
Signed-off-by: Masami Hiramatsu <mhiramat@kernel.org>
Fixes:
d0381c81c2f7 ("kprobes/x86: Set kprobes pages read-only")
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Luis Henriques [Thu, 25 May 2017 15:20:38 +0000 (16:20 +0100)]
ftrace: Fix memory leak in ftrace_graph_release()
ftrace_hash is being kfree'ed in ftrace_graph_release(), however the
->buckets field is not. This results in a memory leak that is easily
captured by kmemleak:
unreferenced object 0xffff880038afe000 (size 8192):
comm "trace-cmd", pid 238, jiffies
4294916898 (age 9.736s)
hex dump (first 32 bytes):
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
backtrace:
[<
ffffffff815f561e>] kmemleak_alloc+0x4e/0xb0
[<
ffffffff8113964d>] __kmalloc+0x12d/0x1a0
[<
ffffffff810bf6d1>] alloc_ftrace_hash+0x51/0x80
[<
ffffffff810c0523>] __ftrace_graph_open.isra.39.constprop.46+0xa3/0x100
[<
ffffffff810c05e8>] ftrace_graph_open+0x68/0xa0
[<
ffffffff8114003d>] do_dentry_open.isra.1+0x1bd/0x2d0
[<
ffffffff81140df7>] vfs_open+0x47/0x60
[<
ffffffff81150f95>] path_openat+0x2a5/0x1020
[<
ffffffff81152d6a>] do_filp_open+0x8a/0xf0
[<
ffffffff811411df>] do_sys_open+0x12f/0x200
[<
ffffffff811412ce>] SyS_open+0x1e/0x20
[<
ffffffff815fa6e0>] entry_SYSCALL_64_fastpath+0x13/0x94
[<
ffffffffffffffff>] 0xffffffffffffffff
Link: http://lkml.kernel.org/r/20170525152038.7661-1-lhenriques@suse.com
Cc: stable@vger.kernel.org
Fixes:
b9b0c831bed2 ("ftrace: Convert graph filter to use hash tables")
Signed-off-by: Luis Henriques <lhenriques@suse.com>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Linus Torvalds [Fri, 26 May 2017 23:45:13 +0000 (16:45 -0700)]
Merge branch 'for-linus' of git://git./linux/kernel/git/dtor/input
Pull input layer fixes from Dmitry Torokhov:
"Just a few fixups to a couple of drivers"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: elan_i2c - ignore signals when finishing updating firmware
Input: elan_i2c - clear INT before resetting controller
Input: atmel_mxt_ts - add T100 as a readable object
Input: edt-ft5x06 - increase allowed data range for threshold parameter
Linus Torvalds [Fri, 26 May 2017 21:02:30 +0000 (14:02 -0700)]
Merge tag 'led_fixes_for_4-12-rc3' of git://git./linux/kernel/git/j.anaszewski/linux-leds
Pull LED fix from Jacek Anaszewski:
"A single LED fix for 4.12-rc3.
leds-pca955x driver uses only i2c_smbus API and thus it should pass
I2C_FUNC_SMBUS_BYTE_DATA flag to i2c_check_functionality"
* tag 'led_fixes_for_4-12-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/j.anaszewski/linux-leds:
leds: pca955x: Correct I2C Functionality
projects / GitHub / LineageOS / android_kernel_motorola_exynos9610.git / log