From fae2b904aa85beecd0950026de28921ae65fb3da Mon Sep 17 00:00:00 2001 From: Felipe Balbi Date: Fri, 14 Oct 2011 13:00:30 +0300 Subject: [PATCH] usb: dwc3: workaround: U1/U2 -> U0 transiton RTL revisions <1.83a have an issue where, depending on the link partner, the USB link might do multiple entry/exit of low power states before a transfer takes place causing degraded throughput. The suggested workaround is to clear bits 12:9 of DCTL register if we see a transition from U1|U2 to U0 and only re-enable that on a transfer complete IRQ and we have no pending transfers on any of the enabled endpoints. Signed-off-by: Felipe Balbi --- drivers/usb/dwc3/core.h | 2 ++ drivers/usb/dwc3/gadget.c | 76 +++++++++++++++++++++++++++++++++++++-- 2 files changed, 76 insertions(+), 2 deletions(-) diff --git a/drivers/usb/dwc3/core.h b/drivers/usb/dwc3/core.h index dc2db165412b..b901a4d3b068 100644 --- a/drivers/usb/dwc3/core.h +++ b/drivers/usb/dwc3/core.h @@ -569,6 +569,7 @@ struct dwc3_hwparams { * @regs_size: address space size * @irq: IRQ number * @num_event_buffers: calculated number of event buffers + * @u1u2: only used on revisions <1.83a for workaround * @maximum_speed: maximum speed requested (mainly for testing purposes) * @revision: revision register contents * @mode: mode of operation @@ -614,6 +615,7 @@ struct dwc3 { int irq; u32 num_event_buffers; + u32 u1u2; u32 maximum_speed; u32 revision; u32 mode; diff --git a/drivers/usb/dwc3/gadget.c b/drivers/usb/dwc3/gadget.c index 85cf392365cb..0a6deeaf3377 100644 --- a/drivers/usb/dwc3/gadget.c +++ b/drivers/usb/dwc3/gadget.c @@ -1376,6 +1376,31 @@ static void dwc3_endpoint_transfer_complete(struct dwc3 *dwc, dep->flags &= ~DWC3_EP_BUSY; dep->res_trans_idx = 0; } + + /* + * WORKAROUND: This is the 2nd half of U1/U2 -> U0 workaround. + * See dwc3_gadget_linksts_change_interrupt() for 1st half. + */ + if (dwc->revision < DWC3_REVISION_183A) { + u32 reg; + int i; + + for (i = 0; i < DWC3_ENDPOINTS_NUM; i++) { + struct dwc3_ep *dep = dwc->eps[i]; + + if (!(dep->flags & DWC3_EP_ENABLED)) + continue; + + if (!list_empty(&dep->req_queued)) + return; + } + + reg = dwc3_readl(dwc->regs, DWC3_DCTL); + reg |= dwc->u1u2; + dwc3_writel(dwc->regs, DWC3_DCTL, reg); + + dwc->u1u2 = 0; + } } static void dwc3_gadget_start_isoc(struct dwc3 *dwc, @@ -1794,8 +1819,55 @@ static void dwc3_gadget_wakeup_interrupt(struct dwc3 *dwc) static void dwc3_gadget_linksts_change_interrupt(struct dwc3 *dwc, unsigned int evtinfo) { - /* The fith bit says SuperSpeed yes or no. */ - dwc->link_state = evtinfo & DWC3_LINK_STATE_MASK; + enum dwc3_link_state next = evtinfo & DWC3_LINK_STATE_MASK; + + /* + * WORKAROUND: DWC3 Revisions <1.83a have an issue which, depending + * on the link partner, the USB session might do multiple entry/exit + * of low power states before a transfer takes place. + * + * Due to this problem, we might experience lower throughput. The + * suggested workaround is to disable DCTL[12:9] bits if we're + * transitioning from U1/U2 to U0 and enable those bits again + * after a transfer completes and there are no pending transfers + * on any of the enabled endpoints. + * + * This is the first half of that workaround. + * + * Refers to: + * + * STAR#9000446952: RTL: Device SS : if U1/U2 ->U0 takes >128us + * core send LGO_Ux entering U0 + */ + if (dwc->revision < DWC3_REVISION_183A) { + if (next == DWC3_LINK_STATE_U0) { + u32 u1u2; + u32 reg; + + switch (dwc->link_state) { + case DWC3_LINK_STATE_U1: + case DWC3_LINK_STATE_U2: + reg = dwc3_readl(dwc->regs, DWC3_DCTL); + u1u2 = reg & (DWC3_DCTL_INITU2ENA + | DWC3_DCTL_ACCEPTU2ENA + | DWC3_DCTL_INITU1ENA + | DWC3_DCTL_ACCEPTU1ENA); + + if (!dwc->u1u2) + dwc->u1u2 = reg & u1u2; + + reg &= ~u1u2; + + dwc3_writel(dwc->regs, DWC3_DCTL, reg); + break; + default: + /* do nothing */ + break; + } + } + } + + dwc->link_state = next; dev_vdbg(dwc->dev, "%s link %d\n", __func__, dwc->link_state); } -- 2.20.1