From ebd10e0783d9fb92a147e60902e22c2d3f3ad69d Mon Sep 17 00:00:00 2001 From: Virupax Sadashivpetimath Date: Fri, 13 May 2011 12:30:23 +0200 Subject: [PATCH] i2c-nomadik: add code to retry on timeout failure It is seen that i2c-nomadik controller randomly stops generating the interrupts leading to a i2c timeout. As a workaround to this problem, add retries to the on going transfer on failure. Signed-off-by: Virupax Sadashivpetimath Reviewed-by: Jonas ABERG Signed-off-by: Linus Walleij Signed-off-by: Ben Dooks --- drivers/i2c/busses/i2c-nomadik.c | 97 ++++++++++++++++---------------- 1 file changed, 49 insertions(+), 48 deletions(-) diff --git a/drivers/i2c/busses/i2c-nomadik.c b/drivers/i2c/busses/i2c-nomadik.c index 234e4a9070b8..b49ff25a2688 100644 --- a/drivers/i2c/busses/i2c-nomadik.c +++ b/drivers/i2c/busses/i2c-nomadik.c @@ -255,8 +255,6 @@ static int init_hw(struct nmk_i2c_dev *dev) { int stat; - clk_enable(dev->clk); - stat = flush_i2c_fifo(dev); if (stat) goto exit; @@ -271,8 +269,6 @@ static int init_hw(struct nmk_i2c_dev *dev) dev->cli.operation = I2C_NO_OPERATION; exit: - /* TODO: Why disable clocks after init hw? */ - clk_disable(dev->clk); /* * TODO: What is this delay for? * Must be pretty pointless since the hw block @@ -572,6 +568,7 @@ static int nmk_i2c_xfer(struct i2c_adapter *i2c_adap, u32 cause; struct nmk_i2c_dev *dev = i2c_get_adapdata(i2c_adap); u32 i2c_sr; + int j; dev->busy = true; @@ -579,63 +576,67 @@ static int nmk_i2c_xfer(struct i2c_adapter *i2c_adap, regulator_enable(dev->regulator); pm_runtime_get_sync(&dev->pdev->dev); + clk_enable(dev->clk); + status = init_hw(dev); if (status) - goto out2; + goto out; - clk_enable(dev->clk); - - /* setup the i2c controller */ - setup_i2c_controller(dev); + for (j = 0; j < 3; j++) { + /* setup the i2c controller */ + setup_i2c_controller(dev); - for (i = 0; i < num_msgs; i++) { - if (unlikely(msgs[i].flags & I2C_M_TEN)) { - dev_err(&dev->pdev->dev, "10 bit addressing" - "not supported\n"); + for (i = 0; i < num_msgs; i++) { + if (unlikely(msgs[i].flags & I2C_M_TEN)) { + dev_err(&dev->pdev->dev, "10 bit addressing" + "not supported\n"); - status = -EINVAL; - goto out; - } - dev->cli.slave_adr = msgs[i].addr; - dev->cli.buffer = msgs[i].buf; - dev->cli.count = msgs[i].len; - dev->stop = (i < (num_msgs - 1)) ? 0 : 1; - dev->result = 0; - - if (msgs[i].flags & I2C_M_RD) { - /* it is a read operation */ - dev->cli.operation = I2C_READ; - status = read_i2c(dev); - } else { - /* write operation */ - dev->cli.operation = I2C_WRITE; - status = write_i2c(dev); - } - if (status || (dev->result)) { - i2c_sr = readl(dev->virtbase + I2C_SR); - /* - * Check if the controller I2C operation status is set - * to ABORT(11b). - */ - if (((i2c_sr >> 2) & 0x3) == 0x3) { - /* get the abort cause */ - cause = (i2c_sr >> 4) - & 0x7; - dev_err(&dev->pdev->dev, "%s\n", cause >= - ARRAY_SIZE(abort_causes) ? + status = -EINVAL; + goto out; + } + dev->cli.slave_adr = msgs[i].addr; + dev->cli.buffer = msgs[i].buf; + dev->cli.count = msgs[i].len; + dev->stop = (i < (num_msgs - 1)) ? 0 : 1; + dev->result = 0; + + if (msgs[i].flags & I2C_M_RD) { + /* it is a read operation */ + dev->cli.operation = I2C_READ; + status = read_i2c(dev); + } else { + /* write operation */ + dev->cli.operation = I2C_WRITE; + status = write_i2c(dev); + } + if (status || (dev->result)) { + i2c_sr = readl(dev->virtbase + I2C_SR); + /* + * Check if the controller I2C operation status + * is set to ABORT(11b). + */ + if (((i2c_sr >> 2) & 0x3) == 0x3) { + /* get the abort cause */ + cause = (i2c_sr >> 4) + & 0x7; + dev_err(&dev->pdev->dev, "%s\n", cause + >= ARRAY_SIZE(abort_causes) ? "unknown reason" : abort_causes[cause]); - } + } - status = status ? status : dev->result; - goto out; + status = status ? status : dev->result; + + break; + } + udelay(I2C_DELAY); } - udelay(I2C_DELAY); + if (status == 0) + break; } out: clk_disable(dev->clk); -out2: pm_runtime_put_sync(&dev->pdev->dev); if (dev->regulator) regulator_disable(dev->regulator); -- 2.20.1