From eac3b2127749af8ba033a755efdc0d4b43167906 Mon Sep 17 00:00:00 2001 From: Stanislaw Gruszka Date: Wed, 31 Aug 2011 14:29:46 +0200 Subject: [PATCH] iwlegacy: merge iwl-fh.h into 4965.h Signed-off-by: Stanislaw Gruszka --- drivers/net/wireless/iwlegacy/4965.h | 352 ++++++++++++++++++++- drivers/net/wireless/iwlegacy/iwl-fh.h | 417 ------------------------- 2 files changed, 351 insertions(+), 418 deletions(-) delete mode 100644 drivers/net/wireless/iwlegacy/iwl-fh.h diff --git a/drivers/net/wireless/iwlegacy/4965.h b/drivers/net/wireless/iwlegacy/4965.h index 5234de72a279..10d0b13e0e3c 100644 --- a/drivers/net/wireless/iwlegacy/4965.h +++ b/drivers/net/wireless/iwlegacy/4965.h @@ -30,7 +30,6 @@ #ifndef __il_4965_h__ #define __il_4965_h__ -#include "iwl-fh.h" #include "iwl-debug.h" struct il_rx_queue; @@ -1001,4 +1000,355 @@ il4965_ucode_general_stats_read(struct file *file, char __user *user_buf, } #endif +/****************************/ +/* Flow Handler Definitions */ +/****************************/ + +/** + * This I/O area is directly read/writable by driver (e.g. Linux uses writel()) + * Addresses are offsets from device's PCI hardware base address. + */ +#define FH49_MEM_LOWER_BOUND (0x1000) +#define FH49_MEM_UPPER_BOUND (0x2000) + +/** + * Keep-Warm (KW) buffer base address. + * + * Driver must allocate a 4KByte buffer that is used by 4965 for keeping the + * host DRAM powered on (via dummy accesses to DRAM) to maintain low-latency + * DRAM access when 4965 is Txing or Rxing. The dummy accesses prevent host + * from going into a power-savings mode that would cause higher DRAM latency, + * and possible data over/under-runs, before all Tx/Rx is complete. + * + * Driver loads FH49_KW_MEM_ADDR_REG with the physical address (bits 35:4) + * of the buffer, which must be 4K aligned. Once this is set up, the 4965 + * automatically invokes keep-warm accesses when normal accesses might not + * be sufficient to maintain fast DRAM response. + * + * Bit fields: + * 31-0: Keep-warm buffer physical base address [35:4], must be 4K aligned + */ +#define FH49_KW_MEM_ADDR_REG (FH49_MEM_LOWER_BOUND + 0x97C) + + +/** + * TFD Circular Buffers Base (CBBC) addresses + * + * 4965 has 16 base pointer registers, one for each of 16 host-DRAM-resident + * circular buffers (CBs/queues) containing Transmit Frame Descriptors (TFDs) + * (see struct il_tfd_frame). These 16 pointer registers are offset by 0x04 + * bytes from one another. Each TFD circular buffer in DRAM must be 256-byte + * aligned (address bits 0-7 must be 0). + * + * Bit fields in each pointer register: + * 27-0: TFD CB physical base address [35:8], must be 256-byte aligned + */ +#define FH49_MEM_CBBC_LOWER_BOUND (FH49_MEM_LOWER_BOUND + 0x9D0) +#define FH49_MEM_CBBC_UPPER_BOUND (FH49_MEM_LOWER_BOUND + 0xA10) + +/* Find TFD CB base pointer for given queue (range 0-15). */ +#define FH49_MEM_CBBC_QUEUE(x) (FH49_MEM_CBBC_LOWER_BOUND + (x) * 0x4) + + +/** + * Rx SRAM Control and Status Registers (RSCSR) + * + * These registers provide handshake between driver and 4965 for the Rx queue + * (this queue handles *all* command responses, notifications, Rx data, etc. + * sent from 4965 uCode to host driver). Unlike Tx, there is only one Rx + * queue, and only one Rx DMA/FIFO channel. Also unlike Tx, which can + * concatenate up to 20 DRAM buffers to form a Tx frame, each Receive Buffer + * Descriptor (RBD) points to only one Rx Buffer (RB); there is a 1:1 + * mapping between RBDs and RBs. + * + * Driver must allocate host DRAM memory for the following, and set the + * physical address of each into 4965 registers: + * + * 1) Receive Buffer Descriptor (RBD) circular buffer (CB), typically with 256 + * entries (although any power of 2, up to 4096, is selectable by driver). + * Each entry (1 dword) points to a receive buffer (RB) of consistent size + * (typically 4K, although 8K or 16K are also selectable by driver). + * Driver sets up RB size and number of RBDs in the CB via Rx config + * register FH49_MEM_RCSR_CHNL0_CONFIG_REG. + * + * Bit fields within one RBD: + * 27-0: Receive Buffer physical address bits [35:8], 256-byte aligned + * + * Driver sets physical address [35:8] of base of RBD circular buffer + * into FH49_RSCSR_CHNL0_RBDCB_BASE_REG [27:0]. + * + * 2) Rx status buffer, 8 bytes, in which 4965 indicates which Rx Buffers + * (RBs) have been filled, via a "write pointer", actually the idx of + * the RB's corresponding RBD within the circular buffer. Driver sets + * physical address [35:4] into FH49_RSCSR_CHNL0_STTS_WPTR_REG [31:0]. + * + * Bit fields in lower dword of Rx status buffer (upper dword not used + * by driver; see struct il4965_shared, val0): + * 31-12: Not used by driver + * 11- 0: Index of last filled Rx buffer descriptor + * (4965 writes, driver reads this value) + * + * As the driver prepares Receive Buffers (RBs) for 4965 to fill, driver must + * enter pointers to these RBs into contiguous RBD circular buffer entries, + * and update the 4965's "write" idx register, + * FH49_RSCSR_CHNL0_RBDCB_WPTR_REG. + * + * This "write" idx corresponds to the *next* RBD that the driver will make + * available, i.e. one RBD past the tail of the ready-to-fill RBDs within + * the circular buffer. This value should initially be 0 (before preparing any + * RBs), should be 8 after preparing the first 8 RBs (for example), and must + * wrap back to 0 at the end of the circular buffer (but don't wrap before + * "read" idx has advanced past 1! See below). + * NOTE: 4965 EXPECTS THE WRITE IDX TO BE INCREMENTED IN MULTIPLES OF 8. + * + * As the 4965 fills RBs (referenced from contiguous RBDs within the circular + * buffer), it updates the Rx status buffer in host DRAM, 2) described above, + * to tell the driver the idx of the latest filled RBD. The driver must + * read this "read" idx from DRAM after receiving an Rx interrupt from 4965. + * + * The driver must also internally keep track of a third idx, which is the + * next RBD to process. When receiving an Rx interrupt, driver should process + * all filled but unprocessed RBs up to, but not including, the RB + * corresponding to the "read" idx. For example, if "read" idx becomes "1", + * driver may process the RB pointed to by RBD 0. Depending on volume of + * traffic, there may be many RBs to process. + * + * If read idx == write idx, 4965 thinks there is no room to put new data. + * Due to this, the maximum number of filled RBs is 255, instead of 256. To + * be safe, make sure that there is a gap of at least 2 RBDs between "write" + * and "read" idxes; that is, make sure that there are no more than 254 + * buffers waiting to be filled. + */ +#define FH49_MEM_RSCSR_LOWER_BOUND (FH49_MEM_LOWER_BOUND + 0xBC0) +#define FH49_MEM_RSCSR_UPPER_BOUND (FH49_MEM_LOWER_BOUND + 0xC00) +#define FH49_MEM_RSCSR_CHNL0 (FH49_MEM_RSCSR_LOWER_BOUND) + +/** + * Physical base address of 8-byte Rx Status buffer. + * Bit fields: + * 31-0: Rx status buffer physical base address [35:4], must 16-byte aligned. + */ +#define FH49_RSCSR_CHNL0_STTS_WPTR_REG (FH49_MEM_RSCSR_CHNL0) + +/** + * Physical base address of Rx Buffer Descriptor Circular Buffer. + * Bit fields: + * 27-0: RBD CD physical base address [35:8], must be 256-byte aligned. + */ +#define FH49_RSCSR_CHNL0_RBDCB_BASE_REG (FH49_MEM_RSCSR_CHNL0 + 0x004) + +/** + * Rx write pointer (idx, really!). + * Bit fields: + * 11-0: Index of driver's most recent prepared-to-be-filled RBD, + 1. + * NOTE: For 256-entry circular buffer, use only bits [7:0]. + */ +#define FH49_RSCSR_CHNL0_RBDCB_WPTR_REG (FH49_MEM_RSCSR_CHNL0 + 0x008) +#define FH49_RSCSR_CHNL0_WPTR (FH49_RSCSR_CHNL0_RBDCB_WPTR_REG) + + +/** + * Rx Config/Status Registers (RCSR) + * Rx Config Reg for channel 0 (only channel used) + * + * Driver must initialize FH49_MEM_RCSR_CHNL0_CONFIG_REG as follows for + * normal operation (see bit fields). + * + * Clearing FH49_MEM_RCSR_CHNL0_CONFIG_REG to 0 turns off Rx DMA. + * Driver should poll FH49_MEM_RSSR_RX_STATUS_REG for + * FH49_RSSR_CHNL0_RX_STATUS_CHNL_IDLE (bit 24) before continuing. + * + * Bit fields: + * 31-30: Rx DMA channel enable: '00' off/pause, '01' pause at end of frame, + * '10' operate normally + * 29-24: reserved + * 23-20: # RBDs in circular buffer = 2^value; use "8" for 256 RBDs (normal), + * min "5" for 32 RBDs, max "12" for 4096 RBDs. + * 19-18: reserved + * 17-16: size of each receive buffer; '00' 4K (normal), '01' 8K, + * '10' 12K, '11' 16K. + * 15-14: reserved + * 13-12: IRQ destination; '00' none, '01' host driver (normal operation) + * 11- 4: timeout for closing Rx buffer and interrupting host (units 32 usec) + * typical value 0x10 (about 1/2 msec) + * 3- 0: reserved + */ +#define FH49_MEM_RCSR_LOWER_BOUND (FH49_MEM_LOWER_BOUND + 0xC00) +#define FH49_MEM_RCSR_UPPER_BOUND (FH49_MEM_LOWER_BOUND + 0xCC0) +#define FH49_MEM_RCSR_CHNL0 (FH49_MEM_RCSR_LOWER_BOUND) + +#define FH49_MEM_RCSR_CHNL0_CONFIG_REG (FH49_MEM_RCSR_CHNL0) + +#define FH49_RCSR_CHNL0_RX_CONFIG_RB_TIMEOUT_MSK (0x00000FF0) /* bits 4-11 */ +#define FH49_RCSR_CHNL0_RX_CONFIG_IRQ_DEST_MSK (0x00001000) /* bits 12 */ +#define FH49_RCSR_CHNL0_RX_CONFIG_SINGLE_FRAME_MSK (0x00008000) /* bit 15 */ +#define FH49_RCSR_CHNL0_RX_CONFIG_RB_SIZE_MSK (0x00030000) /* bits 16-17 */ +#define FH49_RCSR_CHNL0_RX_CONFIG_RBDBC_SIZE_MSK (0x00F00000) /* bits 20-23 */ +#define FH49_RCSR_CHNL0_RX_CONFIG_DMA_CHNL_EN_MSK (0xC0000000) /* bits 30-31*/ + +#define FH49_RCSR_RX_CONFIG_RBDCB_SIZE_POS (20) +#define FH49_RCSR_RX_CONFIG_REG_IRQ_RBTH_POS (4) +#define RX_RB_TIMEOUT (0x10) + +#define FH49_RCSR_RX_CONFIG_CHNL_EN_PAUSE_VAL (0x00000000) +#define FH49_RCSR_RX_CONFIG_CHNL_EN_PAUSE_EOF_VAL (0x40000000) +#define FH49_RCSR_RX_CONFIG_CHNL_EN_ENABLE_VAL (0x80000000) + +#define FH49_RCSR_RX_CONFIG_REG_VAL_RB_SIZE_4K (0x00000000) +#define FH49_RCSR_RX_CONFIG_REG_VAL_RB_SIZE_8K (0x00010000) +#define FH49_RCSR_RX_CONFIG_REG_VAL_RB_SIZE_12K (0x00020000) +#define FH49_RCSR_RX_CONFIG_REG_VAL_RB_SIZE_16K (0x00030000) + +#define FH49_RCSR_CHNL0_RX_IGNORE_RXF_EMPTY (0x00000004) +#define FH49_RCSR_CHNL0_RX_CONFIG_IRQ_DEST_NO_INT_VAL (0x00000000) +#define FH49_RCSR_CHNL0_RX_CONFIG_IRQ_DEST_INT_HOST_VAL (0x00001000) + +/** + * Rx Shared Status Registers (RSSR) + * + * After stopping Rx DMA channel (writing 0 to + * FH49_MEM_RCSR_CHNL0_CONFIG_REG), driver must poll + * FH49_MEM_RSSR_RX_STATUS_REG until Rx channel is idle. + * + * Bit fields: + * 24: 1 = Channel 0 is idle + * + * FH49_MEM_RSSR_SHARED_CTRL_REG and FH49_MEM_RSSR_RX_ENABLE_ERR_IRQ2DRV + * contain default values that should not be altered by the driver. + */ +#define FH49_MEM_RSSR_LOWER_BOUND (FH49_MEM_LOWER_BOUND + 0xC40) +#define FH49_MEM_RSSR_UPPER_BOUND (FH49_MEM_LOWER_BOUND + 0xD00) + +#define FH49_MEM_RSSR_SHARED_CTRL_REG (FH49_MEM_RSSR_LOWER_BOUND) +#define FH49_MEM_RSSR_RX_STATUS_REG (FH49_MEM_RSSR_LOWER_BOUND + 0x004) +#define FH49_MEM_RSSR_RX_ENABLE_ERR_IRQ2DRV\ + (FH49_MEM_RSSR_LOWER_BOUND + 0x008) + +#define FH49_RSSR_CHNL0_RX_STATUS_CHNL_IDLE (0x01000000) + +#define FH49_MEM_TFDIB_REG1_ADDR_BITSHIFT 28 + +/* TFDB Area - TFDs buffer table */ +#define FH49_MEM_TFDIB_DRAM_ADDR_LSB_MSK (0xFFFFFFFF) +#define FH49_TFDIB_LOWER_BOUND (FH49_MEM_LOWER_BOUND + 0x900) +#define FH49_TFDIB_UPPER_BOUND (FH49_MEM_LOWER_BOUND + 0x958) +#define FH49_TFDIB_CTRL0_REG(_chnl) (FH49_TFDIB_LOWER_BOUND + 0x8 * (_chnl)) +#define FH49_TFDIB_CTRL1_REG(_chnl) (FH49_TFDIB_LOWER_BOUND + 0x8 * (_chnl) + 0x4) + +/** + * Transmit DMA Channel Control/Status Registers (TCSR) + * + * 4965 has one configuration register for each of 8 Tx DMA/FIFO channels + * supported in hardware (don't confuse these with the 16 Tx queues in DRAM, + * which feed the DMA/FIFO channels); config regs are separated by 0x20 bytes. + * + * To use a Tx DMA channel, driver must initialize its + * FH49_TCSR_CHNL_TX_CONFIG_REG(chnl) with: + * + * FH49_TCSR_TX_CONFIG_REG_VAL_DMA_CHNL_ENABLE | + * FH49_TCSR_TX_CONFIG_REG_VAL_DMA_CREDIT_ENABLE_VAL + * + * All other bits should be 0. + * + * Bit fields: + * 31-30: Tx DMA channel enable: '00' off/pause, '01' pause at end of frame, + * '10' operate normally + * 29- 4: Reserved, set to "0" + * 3: Enable internal DMA requests (1, normal operation), disable (0) + * 2- 0: Reserved, set to "0" + */ +#define FH49_TCSR_LOWER_BOUND (FH49_MEM_LOWER_BOUND + 0xD00) +#define FH49_TCSR_UPPER_BOUND (FH49_MEM_LOWER_BOUND + 0xE60) + +/* Find Control/Status reg for given Tx DMA/FIFO channel */ +#define FH49_TCSR_CHNL_NUM (7) +#define FH50_TCSR_CHNL_NUM (8) + +/* TCSR: tx_config register values */ +#define FH49_TCSR_CHNL_TX_CONFIG_REG(_chnl) \ + (FH49_TCSR_LOWER_BOUND + 0x20 * (_chnl)) +#define FH49_TCSR_CHNL_TX_CREDIT_REG(_chnl) \ + (FH49_TCSR_LOWER_BOUND + 0x20 * (_chnl) + 0x4) +#define FH49_TCSR_CHNL_TX_BUF_STS_REG(_chnl) \ + (FH49_TCSR_LOWER_BOUND + 0x20 * (_chnl) + 0x8) + +#define FH49_TCSR_TX_CONFIG_REG_VAL_MSG_MODE_TXF (0x00000000) +#define FH49_TCSR_TX_CONFIG_REG_VAL_MSG_MODE_DRV (0x00000001) + +#define FH49_TCSR_TX_CONFIG_REG_VAL_DMA_CREDIT_DISABLE (0x00000000) +#define FH49_TCSR_TX_CONFIG_REG_VAL_DMA_CREDIT_ENABLE (0x00000008) + +#define FH49_TCSR_TX_CONFIG_REG_VAL_CIRQ_HOST_NOINT (0x00000000) +#define FH49_TCSR_TX_CONFIG_REG_VAL_CIRQ_HOST_ENDTFD (0x00100000) +#define FH49_TCSR_TX_CONFIG_REG_VAL_CIRQ_HOST_IFTFD (0x00200000) + +#define FH49_TCSR_TX_CONFIG_REG_VAL_CIRQ_RTC_NOINT (0x00000000) +#define FH49_TCSR_TX_CONFIG_REG_VAL_CIRQ_RTC_ENDTFD (0x00400000) +#define FH49_TCSR_TX_CONFIG_REG_VAL_CIRQ_RTC_IFTFD (0x00800000) + +#define FH49_TCSR_TX_CONFIG_REG_VAL_DMA_CHNL_PAUSE (0x00000000) +#define FH49_TCSR_TX_CONFIG_REG_VAL_DMA_CHNL_PAUSE_EOF (0x40000000) +#define FH49_TCSR_TX_CONFIG_REG_VAL_DMA_CHNL_ENABLE (0x80000000) + +#define FH49_TCSR_CHNL_TX_BUF_STS_REG_VAL_TFDB_EMPTY (0x00000000) +#define FH49_TCSR_CHNL_TX_BUF_STS_REG_VAL_TFDB_WAIT (0x00002000) +#define FH49_TCSR_CHNL_TX_BUF_STS_REG_VAL_TFDB_VALID (0x00000003) + +#define FH49_TCSR_CHNL_TX_BUF_STS_REG_POS_TB_NUM (20) +#define FH49_TCSR_CHNL_TX_BUF_STS_REG_POS_TB_IDX (12) + +/** + * Tx Shared Status Registers (TSSR) + * + * After stopping Tx DMA channel (writing 0 to + * FH49_TCSR_CHNL_TX_CONFIG_REG(chnl)), driver must poll + * FH49_TSSR_TX_STATUS_REG until selected Tx channel is idle + * (channel's buffers empty | no pending requests). + * + * Bit fields: + * 31-24: 1 = Channel buffers empty (channel 7:0) + * 23-16: 1 = No pending requests (channel 7:0) + */ +#define FH49_TSSR_LOWER_BOUND (FH49_MEM_LOWER_BOUND + 0xEA0) +#define FH49_TSSR_UPPER_BOUND (FH49_MEM_LOWER_BOUND + 0xEC0) + +#define FH49_TSSR_TX_STATUS_REG (FH49_TSSR_LOWER_BOUND + 0x010) + +/** + * Bit fields for TSSR(Tx Shared Status & Control) error status register: + * 31: Indicates an address error when accessed to internal memory + * uCode/driver must write "1" in order to clear this flag + * 30: Indicates that Host did not send the expected number of dwords to FH + * uCode/driver must write "1" in order to clear this flag + * 16-9:Each status bit is for one channel. Indicates that an (Error) ActDMA + * command was received from the scheduler while the TRB was already full + * with previous command + * uCode/driver must write "1" in order to clear this flag + * 7-0: Each status bit indicates a channel's TxCredit error. When an error + * bit is set, it indicates that the FH has received a full indication + * from the RTC TxFIFO and the current value of the TxCredit counter was + * not equal to zero. This mean that the credit mechanism was not + * synchronized to the TxFIFO status + * uCode/driver must write "1" in order to clear this flag + */ +#define FH49_TSSR_TX_ERROR_REG (FH49_TSSR_LOWER_BOUND + 0x018) + +#define FH49_TSSR_TX_STATUS_REG_MSK_CHNL_IDLE(_chnl) ((1 << (_chnl)) << 16) + +/* Tx service channels */ +#define FH49_SRVC_CHNL (9) +#define FH49_SRVC_LOWER_BOUND (FH49_MEM_LOWER_BOUND + 0x9C8) +#define FH49_SRVC_UPPER_BOUND (FH49_MEM_LOWER_BOUND + 0x9D0) +#define FH49_SRVC_CHNL_SRAM_ADDR_REG(_chnl) \ + (FH49_SRVC_LOWER_BOUND + ((_chnl) - 9) * 0x4) + +#define FH49_TX_CHICKEN_BITS_REG (FH49_MEM_LOWER_BOUND + 0xE98) +/* Instruct FH to increment the retry count of a packet when + * it is brought from the memory to TX-FIFO + */ +#define FH49_TX_CHICKEN_BITS_SCD_AUTO_RETRY_EN (0x00000002) + +/* Keep Warm Size */ +#define IL_KW_SIZE 0x1000 /* 4k */ + #endif /* __il_4965_h__ */ diff --git a/drivers/net/wireless/iwlegacy/iwl-fh.h b/drivers/net/wireless/iwlegacy/iwl-fh.h deleted file mode 100644 index ac7c21283205..000000000000 --- a/drivers/net/wireless/iwlegacy/iwl-fh.h +++ /dev/null @@ -1,417 +0,0 @@ -/****************************************************************************** - * - * This file is provided under a dual BSD/GPLv2 license. When using or - * redistributing this file, you may do so under either license. - * - * GPL LICENSE SUMMARY - * - * Copyright(c) 2005 - 2011 Intel Corporation. All rights reserved. - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of version 2 of the GNU General Public License as - * published by the Free Software Foundation. - * - * This program is distributed in the hope that it will be useful, but - * WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU - * General Public License for more details. - * - * You should have received a copy of the GNU General Public License - * along with this program; if not, write to the Free Software - * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA 02110, - * USA - * - * The full GNU General Public License is included in this distribution - * in the file called LICENSE.GPL. - * - * Contact Information: - * Intel Linux Wireless - * Intel Corporation, 5200 N.E. Elam Young Parkway, Hillsboro, OR 97124-6497 - * - * BSD LICENSE - * - * Copyright(c) 2005 - 2011 Intel Corporation. All rights reserved. - * All rights reserved. - * - * Redistribution and use in source and binary forms, with or without - * modification, are permitted provided that the following conditions - * are met: - * - * * Redistributions of source code must retain the above copyright - * notice, this list of conditions and the following disclaimer. - * * Redistributions in binary form must reproduce the above copyright - * notice, this list of conditions and the following disclaimer in - * the documentation and/or other materials provided with the - * distribution. - * * Neither the name Intel Corporation nor the names of its - * contributors may be used to endorse or promote products derived - * from this software without specific prior written permission. - * - * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS - * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT - * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR - * A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT - * OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, - * SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT - * LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, - * DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY - * THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT - * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE - * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. - * - *****************************************************************************/ -#ifndef __il_fh_h__ -#define __il_fh_h__ - -/****************************/ -/* Flow Handler Definitions */ -/****************************/ - -/** - * This I/O area is directly read/writable by driver (e.g. Linux uses writel()) - * Addresses are offsets from device's PCI hardware base address. - */ -#define FH49_MEM_LOWER_BOUND (0x1000) -#define FH49_MEM_UPPER_BOUND (0x2000) - -/** - * Keep-Warm (KW) buffer base address. - * - * Driver must allocate a 4KByte buffer that is used by 4965 for keeping the - * host DRAM powered on (via dummy accesses to DRAM) to maintain low-latency - * DRAM access when 4965 is Txing or Rxing. The dummy accesses prevent host - * from going into a power-savings mode that would cause higher DRAM latency, - * and possible data over/under-runs, before all Tx/Rx is complete. - * - * Driver loads FH49_KW_MEM_ADDR_REG with the physical address (bits 35:4) - * of the buffer, which must be 4K aligned. Once this is set up, the 4965 - * automatically invokes keep-warm accesses when normal accesses might not - * be sufficient to maintain fast DRAM response. - * - * Bit fields: - * 31-0: Keep-warm buffer physical base address [35:4], must be 4K aligned - */ -#define FH49_KW_MEM_ADDR_REG (FH49_MEM_LOWER_BOUND + 0x97C) - - -/** - * TFD Circular Buffers Base (CBBC) addresses - * - * 4965 has 16 base pointer registers, one for each of 16 host-DRAM-resident - * circular buffers (CBs/queues) containing Transmit Frame Descriptors (TFDs) - * (see struct il_tfd_frame). These 16 pointer registers are offset by 0x04 - * bytes from one another. Each TFD circular buffer in DRAM must be 256-byte - * aligned (address bits 0-7 must be 0). - * - * Bit fields in each pointer register: - * 27-0: TFD CB physical base address [35:8], must be 256-byte aligned - */ -#define FH49_MEM_CBBC_LOWER_BOUND (FH49_MEM_LOWER_BOUND + 0x9D0) -#define FH49_MEM_CBBC_UPPER_BOUND (FH49_MEM_LOWER_BOUND + 0xA10) - -/* Find TFD CB base pointer for given queue (range 0-15). */ -#define FH49_MEM_CBBC_QUEUE(x) (FH49_MEM_CBBC_LOWER_BOUND + (x) * 0x4) - - -/** - * Rx SRAM Control and Status Registers (RSCSR) - * - * These registers provide handshake between driver and 4965 for the Rx queue - * (this queue handles *all* command responses, notifications, Rx data, etc. - * sent from 4965 uCode to host driver). Unlike Tx, there is only one Rx - * queue, and only one Rx DMA/FIFO channel. Also unlike Tx, which can - * concatenate up to 20 DRAM buffers to form a Tx frame, each Receive Buffer - * Descriptor (RBD) points to only one Rx Buffer (RB); there is a 1:1 - * mapping between RBDs and RBs. - * - * Driver must allocate host DRAM memory for the following, and set the - * physical address of each into 4965 registers: - * - * 1) Receive Buffer Descriptor (RBD) circular buffer (CB), typically with 256 - * entries (although any power of 2, up to 4096, is selectable by driver). - * Each entry (1 dword) points to a receive buffer (RB) of consistent size - * (typically 4K, although 8K or 16K are also selectable by driver). - * Driver sets up RB size and number of RBDs in the CB via Rx config - * register FH49_MEM_RCSR_CHNL0_CONFIG_REG. - * - * Bit fields within one RBD: - * 27-0: Receive Buffer physical address bits [35:8], 256-byte aligned - * - * Driver sets physical address [35:8] of base of RBD circular buffer - * into FH49_RSCSR_CHNL0_RBDCB_BASE_REG [27:0]. - * - * 2) Rx status buffer, 8 bytes, in which 4965 indicates which Rx Buffers - * (RBs) have been filled, via a "write pointer", actually the idx of - * the RB's corresponding RBD within the circular buffer. Driver sets - * physical address [35:4] into FH49_RSCSR_CHNL0_STTS_WPTR_REG [31:0]. - * - * Bit fields in lower dword of Rx status buffer (upper dword not used - * by driver; see struct il4965_shared, val0): - * 31-12: Not used by driver - * 11- 0: Index of last filled Rx buffer descriptor - * (4965 writes, driver reads this value) - * - * As the driver prepares Receive Buffers (RBs) for 4965 to fill, driver must - * enter pointers to these RBs into contiguous RBD circular buffer entries, - * and update the 4965's "write" idx register, - * FH49_RSCSR_CHNL0_RBDCB_WPTR_REG. - * - * This "write" idx corresponds to the *next* RBD that the driver will make - * available, i.e. one RBD past the tail of the ready-to-fill RBDs within - * the circular buffer. This value should initially be 0 (before preparing any - * RBs), should be 8 after preparing the first 8 RBs (for example), and must - * wrap back to 0 at the end of the circular buffer (but don't wrap before - * "read" idx has advanced past 1! See below). - * NOTE: 4965 EXPECTS THE WRITE IDX TO BE INCREMENTED IN MULTIPLES OF 8. - * - * As the 4965 fills RBs (referenced from contiguous RBDs within the circular - * buffer), it updates the Rx status buffer in host DRAM, 2) described above, - * to tell the driver the idx of the latest filled RBD. The driver must - * read this "read" idx from DRAM after receiving an Rx interrupt from 4965. - * - * The driver must also internally keep track of a third idx, which is the - * next RBD to process. When receiving an Rx interrupt, driver should process - * all filled but unprocessed RBs up to, but not including, the RB - * corresponding to the "read" idx. For example, if "read" idx becomes "1", - * driver may process the RB pointed to by RBD 0. Depending on volume of - * traffic, there may be many RBs to process. - * - * If read idx == write idx, 4965 thinks there is no room to put new data. - * Due to this, the maximum number of filled RBs is 255, instead of 256. To - * be safe, make sure that there is a gap of at least 2 RBDs between "write" - * and "read" idxes; that is, make sure that there are no more than 254 - * buffers waiting to be filled. - */ -#define FH49_MEM_RSCSR_LOWER_BOUND (FH49_MEM_LOWER_BOUND + 0xBC0) -#define FH49_MEM_RSCSR_UPPER_BOUND (FH49_MEM_LOWER_BOUND + 0xC00) -#define FH49_MEM_RSCSR_CHNL0 (FH49_MEM_RSCSR_LOWER_BOUND) - -/** - * Physical base address of 8-byte Rx Status buffer. - * Bit fields: - * 31-0: Rx status buffer physical base address [35:4], must 16-byte aligned. - */ -#define FH49_RSCSR_CHNL0_STTS_WPTR_REG (FH49_MEM_RSCSR_CHNL0) - -/** - * Physical base address of Rx Buffer Descriptor Circular Buffer. - * Bit fields: - * 27-0: RBD CD physical base address [35:8], must be 256-byte aligned. - */ -#define FH49_RSCSR_CHNL0_RBDCB_BASE_REG (FH49_MEM_RSCSR_CHNL0 + 0x004) - -/** - * Rx write pointer (idx, really!). - * Bit fields: - * 11-0: Index of driver's most recent prepared-to-be-filled RBD, + 1. - * NOTE: For 256-entry circular buffer, use only bits [7:0]. - */ -#define FH49_RSCSR_CHNL0_RBDCB_WPTR_REG (FH49_MEM_RSCSR_CHNL0 + 0x008) -#define FH49_RSCSR_CHNL0_WPTR (FH49_RSCSR_CHNL0_RBDCB_WPTR_REG) - - -/** - * Rx Config/Status Registers (RCSR) - * Rx Config Reg for channel 0 (only channel used) - * - * Driver must initialize FH49_MEM_RCSR_CHNL0_CONFIG_REG as follows for - * normal operation (see bit fields). - * - * Clearing FH49_MEM_RCSR_CHNL0_CONFIG_REG to 0 turns off Rx DMA. - * Driver should poll FH49_MEM_RSSR_RX_STATUS_REG for - * FH49_RSSR_CHNL0_RX_STATUS_CHNL_IDLE (bit 24) before continuing. - * - * Bit fields: - * 31-30: Rx DMA channel enable: '00' off/pause, '01' pause at end of frame, - * '10' operate normally - * 29-24: reserved - * 23-20: # RBDs in circular buffer = 2^value; use "8" for 256 RBDs (normal), - * min "5" for 32 RBDs, max "12" for 4096 RBDs. - * 19-18: reserved - * 17-16: size of each receive buffer; '00' 4K (normal), '01' 8K, - * '10' 12K, '11' 16K. - * 15-14: reserved - * 13-12: IRQ destination; '00' none, '01' host driver (normal operation) - * 11- 4: timeout for closing Rx buffer and interrupting host (units 32 usec) - * typical value 0x10 (about 1/2 msec) - * 3- 0: reserved - */ -#define FH49_MEM_RCSR_LOWER_BOUND (FH49_MEM_LOWER_BOUND + 0xC00) -#define FH49_MEM_RCSR_UPPER_BOUND (FH49_MEM_LOWER_BOUND + 0xCC0) -#define FH49_MEM_RCSR_CHNL0 (FH49_MEM_RCSR_LOWER_BOUND) - -#define FH49_MEM_RCSR_CHNL0_CONFIG_REG (FH49_MEM_RCSR_CHNL0) - -#define FH49_RCSR_CHNL0_RX_CONFIG_RB_TIMEOUT_MSK (0x00000FF0) /* bits 4-11 */ -#define FH49_RCSR_CHNL0_RX_CONFIG_IRQ_DEST_MSK (0x00001000) /* bits 12 */ -#define FH49_RCSR_CHNL0_RX_CONFIG_SINGLE_FRAME_MSK (0x00008000) /* bit 15 */ -#define FH49_RCSR_CHNL0_RX_CONFIG_RB_SIZE_MSK (0x00030000) /* bits 16-17 */ -#define FH49_RCSR_CHNL0_RX_CONFIG_RBDBC_SIZE_MSK (0x00F00000) /* bits 20-23 */ -#define FH49_RCSR_CHNL0_RX_CONFIG_DMA_CHNL_EN_MSK (0xC0000000) /* bits 30-31*/ - -#define FH49_RCSR_RX_CONFIG_RBDCB_SIZE_POS (20) -#define FH49_RCSR_RX_CONFIG_REG_IRQ_RBTH_POS (4) -#define RX_RB_TIMEOUT (0x10) - -#define FH49_RCSR_RX_CONFIG_CHNL_EN_PAUSE_VAL (0x00000000) -#define FH49_RCSR_RX_CONFIG_CHNL_EN_PAUSE_EOF_VAL (0x40000000) -#define FH49_RCSR_RX_CONFIG_CHNL_EN_ENABLE_VAL (0x80000000) - -#define FH49_RCSR_RX_CONFIG_REG_VAL_RB_SIZE_4K (0x00000000) -#define FH49_RCSR_RX_CONFIG_REG_VAL_RB_SIZE_8K (0x00010000) -#define FH49_RCSR_RX_CONFIG_REG_VAL_RB_SIZE_12K (0x00020000) -#define FH49_RCSR_RX_CONFIG_REG_VAL_RB_SIZE_16K (0x00030000) - -#define FH49_RCSR_CHNL0_RX_IGNORE_RXF_EMPTY (0x00000004) -#define FH49_RCSR_CHNL0_RX_CONFIG_IRQ_DEST_NO_INT_VAL (0x00000000) -#define FH49_RCSR_CHNL0_RX_CONFIG_IRQ_DEST_INT_HOST_VAL (0x00001000) - -/** - * Rx Shared Status Registers (RSSR) - * - * After stopping Rx DMA channel (writing 0 to - * FH49_MEM_RCSR_CHNL0_CONFIG_REG), driver must poll - * FH49_MEM_RSSR_RX_STATUS_REG until Rx channel is idle. - * - * Bit fields: - * 24: 1 = Channel 0 is idle - * - * FH49_MEM_RSSR_SHARED_CTRL_REG and FH49_MEM_RSSR_RX_ENABLE_ERR_IRQ2DRV - * contain default values that should not be altered by the driver. - */ -#define FH49_MEM_RSSR_LOWER_BOUND (FH49_MEM_LOWER_BOUND + 0xC40) -#define FH49_MEM_RSSR_UPPER_BOUND (FH49_MEM_LOWER_BOUND + 0xD00) - -#define FH49_MEM_RSSR_SHARED_CTRL_REG (FH49_MEM_RSSR_LOWER_BOUND) -#define FH49_MEM_RSSR_RX_STATUS_REG (FH49_MEM_RSSR_LOWER_BOUND + 0x004) -#define FH49_MEM_RSSR_RX_ENABLE_ERR_IRQ2DRV\ - (FH49_MEM_RSSR_LOWER_BOUND + 0x008) - -#define FH49_RSSR_CHNL0_RX_STATUS_CHNL_IDLE (0x01000000) - -#define FH49_MEM_TFDIB_REG1_ADDR_BITSHIFT 28 - -/* TFDB Area - TFDs buffer table */ -#define FH49_MEM_TFDIB_DRAM_ADDR_LSB_MSK (0xFFFFFFFF) -#define FH49_TFDIB_LOWER_BOUND (FH49_MEM_LOWER_BOUND + 0x900) -#define FH49_TFDIB_UPPER_BOUND (FH49_MEM_LOWER_BOUND + 0x958) -#define FH49_TFDIB_CTRL0_REG(_chnl) (FH49_TFDIB_LOWER_BOUND + 0x8 * (_chnl)) -#define FH49_TFDIB_CTRL1_REG(_chnl) (FH49_TFDIB_LOWER_BOUND + 0x8 * (_chnl) + 0x4) - -/** - * Transmit DMA Channel Control/Status Registers (TCSR) - * - * 4965 has one configuration register for each of 8 Tx DMA/FIFO channels - * supported in hardware (don't confuse these with the 16 Tx queues in DRAM, - * which feed the DMA/FIFO channels); config regs are separated by 0x20 bytes. - * - * To use a Tx DMA channel, driver must initialize its - * FH49_TCSR_CHNL_TX_CONFIG_REG(chnl) with: - * - * FH49_TCSR_TX_CONFIG_REG_VAL_DMA_CHNL_ENABLE | - * FH49_TCSR_TX_CONFIG_REG_VAL_DMA_CREDIT_ENABLE_VAL - * - * All other bits should be 0. - * - * Bit fields: - * 31-30: Tx DMA channel enable: '00' off/pause, '01' pause at end of frame, - * '10' operate normally - * 29- 4: Reserved, set to "0" - * 3: Enable internal DMA requests (1, normal operation), disable (0) - * 2- 0: Reserved, set to "0" - */ -#define FH49_TCSR_LOWER_BOUND (FH49_MEM_LOWER_BOUND + 0xD00) -#define FH49_TCSR_UPPER_BOUND (FH49_MEM_LOWER_BOUND + 0xE60) - -/* Find Control/Status reg for given Tx DMA/FIFO channel */ -#define FH49_TCSR_CHNL_NUM (7) -#define FH50_TCSR_CHNL_NUM (8) - -/* TCSR: tx_config register values */ -#define FH49_TCSR_CHNL_TX_CONFIG_REG(_chnl) \ - (FH49_TCSR_LOWER_BOUND + 0x20 * (_chnl)) -#define FH49_TCSR_CHNL_TX_CREDIT_REG(_chnl) \ - (FH49_TCSR_LOWER_BOUND + 0x20 * (_chnl) + 0x4) -#define FH49_TCSR_CHNL_TX_BUF_STS_REG(_chnl) \ - (FH49_TCSR_LOWER_BOUND + 0x20 * (_chnl) + 0x8) - -#define FH49_TCSR_TX_CONFIG_REG_VAL_MSG_MODE_TXF (0x00000000) -#define FH49_TCSR_TX_CONFIG_REG_VAL_MSG_MODE_DRV (0x00000001) - -#define FH49_TCSR_TX_CONFIG_REG_VAL_DMA_CREDIT_DISABLE (0x00000000) -#define FH49_TCSR_TX_CONFIG_REG_VAL_DMA_CREDIT_ENABLE (0x00000008) - -#define FH49_TCSR_TX_CONFIG_REG_VAL_CIRQ_HOST_NOINT (0x00000000) -#define FH49_TCSR_TX_CONFIG_REG_VAL_CIRQ_HOST_ENDTFD (0x00100000) -#define FH49_TCSR_TX_CONFIG_REG_VAL_CIRQ_HOST_IFTFD (0x00200000) - -#define FH49_TCSR_TX_CONFIG_REG_VAL_CIRQ_RTC_NOINT (0x00000000) -#define FH49_TCSR_TX_CONFIG_REG_VAL_CIRQ_RTC_ENDTFD (0x00400000) -#define FH49_TCSR_TX_CONFIG_REG_VAL_CIRQ_RTC_IFTFD (0x00800000) - -#define FH49_TCSR_TX_CONFIG_REG_VAL_DMA_CHNL_PAUSE (0x00000000) -#define FH49_TCSR_TX_CONFIG_REG_VAL_DMA_CHNL_PAUSE_EOF (0x40000000) -#define FH49_TCSR_TX_CONFIG_REG_VAL_DMA_CHNL_ENABLE (0x80000000) - -#define FH49_TCSR_CHNL_TX_BUF_STS_REG_VAL_TFDB_EMPTY (0x00000000) -#define FH49_TCSR_CHNL_TX_BUF_STS_REG_VAL_TFDB_WAIT (0x00002000) -#define FH49_TCSR_CHNL_TX_BUF_STS_REG_VAL_TFDB_VALID (0x00000003) - -#define FH49_TCSR_CHNL_TX_BUF_STS_REG_POS_TB_NUM (20) -#define FH49_TCSR_CHNL_TX_BUF_STS_REG_POS_TB_IDX (12) - -/** - * Tx Shared Status Registers (TSSR) - * - * After stopping Tx DMA channel (writing 0 to - * FH49_TCSR_CHNL_TX_CONFIG_REG(chnl)), driver must poll - * FH49_TSSR_TX_STATUS_REG until selected Tx channel is idle - * (channel's buffers empty | no pending requests). - * - * Bit fields: - * 31-24: 1 = Channel buffers empty (channel 7:0) - * 23-16: 1 = No pending requests (channel 7:0) - */ -#define FH49_TSSR_LOWER_BOUND (FH49_MEM_LOWER_BOUND + 0xEA0) -#define FH49_TSSR_UPPER_BOUND (FH49_MEM_LOWER_BOUND + 0xEC0) - -#define FH49_TSSR_TX_STATUS_REG (FH49_TSSR_LOWER_BOUND + 0x010) - -/** - * Bit fields for TSSR(Tx Shared Status & Control) error status register: - * 31: Indicates an address error when accessed to internal memory - * uCode/driver must write "1" in order to clear this flag - * 30: Indicates that Host did not send the expected number of dwords to FH - * uCode/driver must write "1" in order to clear this flag - * 16-9:Each status bit is for one channel. Indicates that an (Error) ActDMA - * command was received from the scheduler while the TRB was already full - * with previous command - * uCode/driver must write "1" in order to clear this flag - * 7-0: Each status bit indicates a channel's TxCredit error. When an error - * bit is set, it indicates that the FH has received a full indication - * from the RTC TxFIFO and the current value of the TxCredit counter was - * not equal to zero. This mean that the credit mechanism was not - * synchronized to the TxFIFO status - * uCode/driver must write "1" in order to clear this flag - */ -#define FH49_TSSR_TX_ERROR_REG (FH49_TSSR_LOWER_BOUND + 0x018) - -#define FH49_TSSR_TX_STATUS_REG_MSK_CHNL_IDLE(_chnl) ((1 << (_chnl)) << 16) - -/* Tx service channels */ -#define FH49_SRVC_CHNL (9) -#define FH49_SRVC_LOWER_BOUND (FH49_MEM_LOWER_BOUND + 0x9C8) -#define FH49_SRVC_UPPER_BOUND (FH49_MEM_LOWER_BOUND + 0x9D0) -#define FH49_SRVC_CHNL_SRAM_ADDR_REG(_chnl) \ - (FH49_SRVC_LOWER_BOUND + ((_chnl) - 9) * 0x4) - -#define FH49_TX_CHICKEN_BITS_REG (FH49_MEM_LOWER_BOUND + 0xE98) -/* Instruct FH to increment the retry count of a packet when - * it is brought from the memory to TX-FIFO - */ -#define FH49_TX_CHICKEN_BITS_SCD_AUTO_RETRY_EN (0x00000002) - -/* Keep Warm Size */ -#define IL_KW_SIZE 0x1000 /* 4k */ - -#endif /* !__il_fh_h__ */ -- 2.20.1