From e75db4e3685f79e4d9426499565e56e347a9bd25 Mon Sep 17 00:00:00 2001 From: Michal Kazior Date: Thu, 28 Aug 2014 22:14:16 +0300 Subject: [PATCH] ath10k: re-enable interrupts properly in hw recovery Recent changes done to start/restart sequences broke hw recovery in some hw configurations. The pci transport was stopped twice however due to a workaround in the pci disabling code the disable/enable for first msi interrupt was not balanced. This ended up with irqs not being properly re-enabled and the following print out during recovery: ath10k: failed to receive control response completion, polling.. ath10k: Service connect timeout: -110 ath10k: Could not init core: -110 Legacy interrupt mode was unaffected while msi ranged mode would be partially crippled (it would miss fw indication interrupts but otherwise it worked fine). This fixes completely broken fw recovery for a single msi interrupt mode and fixes subsequent fw crash reports for msi range interrupt mode. Signed-off-by: Michal Kazior Signed-off-by: Kalle Valo --- drivers/net/wireless/ath/ath10k/pci.c | 35 +++++++++++---------------- 1 file changed, 14 insertions(+), 21 deletions(-) diff --git a/drivers/net/wireless/ath/ath10k/pci.c b/drivers/net/wireless/ath/ath10k/pci.c index 056a35a77133..6abe9394e8d7 100644 --- a/drivers/net/wireless/ath/ath10k/pci.c +++ b/drivers/net/wireless/ath/ath10k/pci.c @@ -1172,16 +1172,8 @@ static void ath10k_pci_irq_disable(struct ath10k *ar) int i; ath10k_ce_disable_interrupts(ar); - - /* Regardless how many interrupts were assigned for MSI the first one - * is always used for firmware indications (crashes). There's no way to - * mask the irq in the device so call disable_irq(). Legacy (shared) - * interrupts can be masked on the device though. - */ - if (ar_pci->num_msi_intrs > 0) - disable_irq(ar_pci->pdev->irq); - else - ath10k_pci_disable_and_clear_legacy_irq(ar); + ath10k_pci_disable_and_clear_legacy_irq(ar); + /* FIXME: How to mask all MSI interrupts? */ for (i = 0; i < max(1, ar_pci->num_msi_intrs); i++) synchronize_irq(ar_pci->pdev->irq + i); @@ -1189,15 +1181,9 @@ static void ath10k_pci_irq_disable(struct ath10k *ar) static void ath10k_pci_irq_enable(struct ath10k *ar) { - struct ath10k_pci *ar_pci = ath10k_pci_priv(ar); - ath10k_ce_enable_interrupts(ar); - - /* See comment in ath10k_pci_irq_disable() */ - if (ar_pci->num_msi_intrs > 0) - enable_irq(ar_pci->pdev->irq); - else - ath10k_pci_enable_legacy_irq(ar); + ath10k_pci_enable_legacy_irq(ar); + /* FIXME: How to unmask all MSI interrupts? */ } static int ath10k_pci_hif_start(struct ath10k *ar) @@ -1311,14 +1297,21 @@ static void ath10k_pci_hif_stop(struct ath10k *ar) { ath10k_dbg(ar, ATH10K_DBG_BOOT, "boot hif stop\n"); - ath10k_pci_irq_disable(ar); - ath10k_pci_flush(ar); - /* Most likely the device has HTT Rx ring configured. The only way to * prevent the device from accessing (and possible corrupting) host * memory is to reset the chip now. + * + * There's also no known way of masking MSI interrupts on the device. + * For ranged MSI the CE-related interrupts can be masked. However + * regardless how many MSI interrupts are assigned the first one + * is always used for firmware indications (crashes) and cannot be + * masked. To prevent the device from asserting the interrupt reset it + * before proceeding with cleanup. */ ath10k_pci_warm_reset(ar); + + ath10k_pci_irq_disable(ar); + ath10k_pci_flush(ar); } static int ath10k_pci_hif_exchange_bmi_msg(struct ath10k *ar, -- 2.20.1