From cff94887d55a32bf8f7095482d9ba92784280a5c Mon Sep 17 00:00:00 2001
From: Linus Walleij <linus.walleij@linaro.org>
Date: Mon, 15 May 2017 09:50:34 +0200
Subject: [PATCH] ARM: dts: add core I2C devices to the APQ8060 Dragonboard

The APQ8060 Dragonboard has an Atmel AT24c128 EEPROM and a
Wolfson Micro WM8903 codec connected to its GSBI8 I2C bus.
Add entries for these to the device tree. The interrupt line
from the WM8903 chip is not routed anywhere on this design
so it can not be used.

Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
---
 .../arm/boot/dts/qcom-apq8060-dragonboard.dts | 49 +++++++++++++++++++
 1 file changed, 49 insertions(+)

diff --git a/arch/arm/boot/dts/qcom-apq8060-dragonboard.dts b/arch/arm/boot/dts/qcom-apq8060-dragonboard.dts
index 5225e489ef52..9d725f983282 100644
--- a/arch/arm/boot/dts/qcom-apq8060-dragonboard.dts
+++ b/arch/arm/boot/dts/qcom-apq8060-dragonboard.dts
@@ -180,6 +180,19 @@
 				};
 			};
 
+			dragon_gsbi8_i2c_pins: gsbi8_i2c {
+				mux {
+					pins = "gpio64", "gpio65";
+					function = "gsbi8";
+				};
+				pinconf {
+					pins = "gpio64", "gpio65";
+					drive-strength = <16>;
+					/* These have external pull-up 2.2kOhm to 1.8V */
+					bias-disable;
+				};
+			};
+
 			dragon_gsbi12_i2c_pins: gsbi12_i2c {
 				mux {
 					pins = "gpio115", "gpio116";
@@ -448,6 +461,42 @@
 			};
 		};
 
+		gsbi@19800000 {
+			status = "ok";
+			qcom,mode = <GSBI_PROT_I2C>;
+
+			i2c@19880000 {
+				status = "ok";
+				pinctrl-names = "default";
+				pinctrl-0 = <&dragon_gsbi8_i2c_pins>;
+
+				eeprom@52 {
+					/* A 16KiB Platform ID EEPROM on the CPU carrier board */
+					compatible = "atmel,24c128";
+					reg = <0x52>;
+					vcc-supply = <&pm8058_s3>;
+					pagesize = <64>;
+				};
+				wm8903: wm8903@1a {
+					/* This Woolfson Micro device has an unrouted interrupt line */
+					compatible = "wlf,wm8903";
+					reg = <0x1a>;
+
+					AVDD-supply = <&pm8058_l16>;
+					CPVDD-supply = <&pm8058_l16>;
+					DBVDD-supply = <&pm8058_s3>;
+					DCVDD-supply = <&pm8058_l0>;
+
+					gpio-controller;
+					#gpio-cells = <2>;
+
+					micdet-cfg = <0>;
+					micdet-delay = <100>;
+					gpio-cfg = <0xffffffff 0xffffffff 0 0xffffffff 0xffffffff>;
+				};
+			};
+		};
+
 		gsbi@19c00000 {
 			status = "ok";
 			qcom,mode = <GSBI_PROT_I2C_UART>;
-- 
2.20.1