From ccec9038c7217e537f5ae5e3ac5af8293a21bbfd Mon Sep 17 00:00:00 2001 From: David Liu Date: Fri, 24 Jul 2015 20:25:32 +0300 Subject: [PATCH] ath10k: enable raw encap mode and software crypto engine This patch enables raw Rx/Tx encap mode to support software based crypto engine. This patch introduces a new module param 'cryptmode'. cryptmode: 0: Use hardware crypto engine globally with native Wi-Fi mode TX/RX encapsulation to the firmware. This is the default mode. 1: Use sofware crypto engine globally with raw mode TX/RX encapsulation to the firmware. Known limitation: A-MSDU must be disabled for RAW Tx encap mode to perform well when heavy traffic is applied. Testing: (by Michal Kazior ) a) Performance Testing cryptmode=1 ap=qca988x sta=killer1525 killer1525 -> qca988x 194.496 mbps [tcp1 ip4] killer1525 -> qca988x 238.309 mbps [tcp5 ip4] killer1525 -> qca988x 266.958 mbps [udp1 ip4] killer1525 -> qca988x 477.468 mbps [udp5 ip4] qca988x -> killer1525 301.378 mbps [tcp1 ip4] qca988x -> killer1525 297.949 mbps [tcp5 ip4] qca988x -> killer1525 331.351 mbps [udp1 ip4] qca988x -> killer1525 371.528 mbps [udp5 ip4] ap=killer1525 sta=qca988x qca988x -> killer1525 331.447 mbps [tcp1 ip4] qca988x -> killer1525 328.783 mbps [tcp5 ip4] qca988x -> killer1525 375.309 mbps [udp1 ip4] qca988x -> killer1525 403.379 mbps [udp5 ip4] killer1525 -> qca988x 203.689 mbps [tcp1 ip4] killer1525 -> qca988x 222.339 mbps [tcp5 ip4] killer1525 -> qca988x 264.199 mbps [udp1 ip4] killer1525 -> qca988x 479.371 mbps [udp5 ip4] Note: - only open network tested for RAW vs nwifi performance comparison - killer1525 (qca6174 hw2.2) is 2x2 device (hence max 866mbps) - used iperf - OTA, devices a few cm apart from each other, no shielding - tcpX/udpX, X - means number of threads used Overview: - relative Tx performance drop is seen but is within reasonable and expected threshold (A-MSDU must be disabled with RAW Tx) b) Connectivity Testing cryptmode=1 ap=iwl6205 sta1=qca988x crypto=open topology-1ap1sta OK ap=iwl6205 sta1=qca988x crypto=wep1 topology-1ap1sta OK ap=iwl6205 sta1=qca988x crypto=wpa topology-1ap1sta OK ap=iwl6205 sta1=qca988x crypto=wpa-ccmp topology-1ap1sta OK ap=qca988x sta1=iwl6205 crypto=open topology-1ap1sta OK ap=qca988x sta1=iwl6205 crypto=wep1 topology-1ap1sta OK ap=qca988x sta1=iwl6205 crypto=wpa topology-1ap1sta OK ap=qca988x sta1=iwl6205 crypto=wpa-ccmp topology-1ap1sta OK ap=iwl6205 sta1=qca988x crypto=open topology-1ap1sta2br OK ap=iwl6205 sta1=qca988x crypto=wep1 topology-1ap1sta2br OK ap=iwl6205 sta1=qca988x crypto=wpa topology-1ap1sta2br OK ap=iwl6205 sta1=qca988x crypto=wpa-ccmp topology-1ap1sta2br OK ap=qca988x sta1=iwl6205 crypto=open topology-1ap1sta2br OK ap=qca988x sta1=iwl6205 crypto=wep1 topology-1ap1sta2br OK ap=qca988x sta1=iwl6205 crypto=wpa topology-1ap1sta2br OK ap=qca988x sta1=iwl6205 crypto=wpa-ccmp topology-1ap1sta2br OK ap=iwl6205 sta1=qca988x crypto=open topology-1ap1sta2br1vlan OK ap=iwl6205 sta1=qca988x crypto=wep1 topology-1ap1sta2br1vlan OK ap=iwl6205 sta1=qca988x crypto=wpa topology-1ap1sta2br1vlan OK ap=iwl6205 sta1=qca988x crypto=wpa-ccmp topology-1ap1sta2br1vlan OK ap=qca988x sta1=iwl6205 crypto=open topology-1ap1sta2br1vlan OK ap=qca988x sta1=iwl6205 crypto=wep1 topology-1ap1sta2br1vlan OK ap=qca988x sta1=iwl6205 crypto=wpa topology-1ap1sta2br1vlan OK ap=qca988x sta1=iwl6205 crypto=wpa-ccmp topology-1ap1sta2br1vlan OK Note: - each test takes all possible endpoint pairs and pings - each pair-ping flushes arp table - ip6 is used c) Testbed Topology: 1ap1sta: [ap] ---- [sta] endpoints: ap, sta 1ap1sta2br: [veth0] [ap] ---- [sta] [veth2] | | | | [veth1] | \ [veth3] \ / \ / [br0] [br1] endpoints: veth0, veth2, br0, br1 note: STA works in 4addr mode, AP has wds_sta=1 1ap1sta2br1vlan: [veth0] [ap] ---- [sta] [veth2] | | | | [veth1] | \ [veth3] \ / \ / [br0] [br1] | | [vlan0_id2] [vlan1_id2] endpoints: vlan0_id2, vlan1_id2 note: STA works in 4addr mode, AP has wds_sta=1 Credits: Thanks to Michal Kazior who helped find the amsdu issue, contributed a workaround (already squashed into this patch), and contributed the throughput and connectivity tests results. Signed-off-by: David Liu Signed-off-by: Michal Kazior Tested-by: Michal Kazior Signed-off-by: Kalle Valo --- drivers/net/wireless/ath/ath10k/core.c | 43 ++++++++++++++ drivers/net/wireless/ath/ath10k/core.h | 31 ++++++++-- drivers/net/wireless/ath/ath10k/debug.c | 19 +++--- drivers/net/wireless/ath/ath10k/htt.c | 23 +++++++- drivers/net/wireless/ath/ath10k/htt.h | 8 +++ drivers/net/wireless/ath/ath10k/htt_rx.c | 7 ++- drivers/net/wireless/ath/ath10k/htt_tx.c | 12 +++- drivers/net/wireless/ath/ath10k/hw.h | 11 ++-- drivers/net/wireless/ath/ath10k/mac.c | 70 ++++++++++++++++++----- drivers/net/wireless/ath/ath10k/wmi-tlv.c | 2 +- drivers/net/wireless/ath/ath10k/wmi.c | 8 +-- 11 files changed, 183 insertions(+), 51 deletions(-) diff --git a/drivers/net/wireless/ath/ath10k/core.c b/drivers/net/wireless/ath/ath10k/core.c index f79fa6c67ebc..29d2541d87dd 100644 --- a/drivers/net/wireless/ath/ath10k/core.c +++ b/drivers/net/wireless/ath/ath10k/core.c @@ -31,16 +31,19 @@ #include "wmi-ops.h" unsigned int ath10k_debug_mask; +static unsigned int ath10k_cryptmode_param; static bool uart_print; static bool skip_otp; module_param_named(debug_mask, ath10k_debug_mask, uint, 0644); +module_param_named(cryptmode, ath10k_cryptmode_param, uint, 0644); module_param(uart_print, bool, 0644); module_param(skip_otp, bool, 0644); MODULE_PARM_DESC(debug_mask, "Debugging mask"); MODULE_PARM_DESC(uart_print, "Uart target debugging"); MODULE_PARM_DESC(skip_otp, "Skip otp failure for calibration in testmode"); +MODULE_PARM_DESC(cryptmode, "Crypto mode: 0-hardware, 1-software"); static const struct ath10k_hw_params ath10k_hw_params_list[] = { { @@ -1073,6 +1076,46 @@ static int ath10k_core_init_firmware_features(struct ath10k *ar) return -EINVAL; } + ar->wmi.rx_decap_mode = ATH10K_HW_TXRX_NATIVE_WIFI; + switch (ath10k_cryptmode_param) { + case ATH10K_CRYPT_MODE_HW: + clear_bit(ATH10K_FLAG_RAW_MODE, &ar->dev_flags); + clear_bit(ATH10K_FLAG_HW_CRYPTO_DISABLED, &ar->dev_flags); + break; + case ATH10K_CRYPT_MODE_SW: + if (!test_bit(ATH10K_FW_FEATURE_RAW_MODE_SUPPORT, + ar->fw_features)) { + ath10k_err(ar, "cryptmode > 0 requires raw mode support from firmware"); + return -EINVAL; + } + + set_bit(ATH10K_FLAG_RAW_MODE, &ar->dev_flags); + set_bit(ATH10K_FLAG_HW_CRYPTO_DISABLED, &ar->dev_flags); + break; + default: + ath10k_info(ar, "invalid cryptmode: %d\n", + ath10k_cryptmode_param); + return -EINVAL; + } + + ar->htt.max_num_amsdu = ATH10K_HTT_MAX_NUM_AMSDU_DEFAULT; + ar->htt.max_num_ampdu = ATH10K_HTT_MAX_NUM_AMPDU_DEFAULT; + + if (test_bit(ATH10K_FLAG_RAW_MODE, &ar->dev_flags)) { + ar->wmi.rx_decap_mode = ATH10K_HW_TXRX_RAW; + + /* Workaround: + * + * Firmware A-MSDU aggregation breaks with RAW Tx encap mode + * and causes enormous performance issues (malformed frames, + * etc). + * + * Disabling A-MSDU makes RAW mode stable with heavy traffic + * albeit a bit slower compared to regular operation. + */ + ar->htt.max_num_amsdu = 1; + } + /* Backwards compatibility for firmwares without * ATH10K_FW_IE_WMI_OP_VERSION. */ diff --git a/drivers/net/wireless/ath/ath10k/core.h b/drivers/net/wireless/ath/ath10k/core.h index 78e07051b897..35f40388b622 100644 --- a/drivers/net/wireless/ath/ath10k/core.h +++ b/drivers/net/wireless/ath/ath10k/core.h @@ -92,6 +92,7 @@ struct ath10k_skb_cb { u8 tid; u16 freq; bool is_offchan; + bool nohwcrypt; struct ath10k_htt_txbuf *txbuf; u32 txbuf_paddr; } __packed htt; @@ -152,6 +153,7 @@ struct ath10k_wmi { const struct wmi_ops *ops; u32 num_mem_chunks; + u32 rx_decap_mode; struct ath10k_mem_chunk mem_chunks[WMI_MAX_MEM_REQS]; }; @@ -341,6 +343,7 @@ struct ath10k_vif { } u; bool use_cts_prot; + bool nohwcrypt; int num_legacy_stations; int txpower; struct wmi_wmm_params_all_arg wmm_params; @@ -382,9 +385,6 @@ struct ath10k_debug { u32 reg_addr; u32 nf_cal_period; - u8 htt_max_amsdu; - u8 htt_max_ampdu; - struct ath10k_fw_crash_data *fw_crash_data; }; @@ -453,16 +453,21 @@ enum ath10k_fw_features { ATH10K_FW_FEATURE_WOWLAN_SUPPORT = 6, /* Don't trust error code from otp.bin */ - ATH10K_FW_FEATURE_IGNORE_OTP_RESULT, + ATH10K_FW_FEATURE_IGNORE_OTP_RESULT = 7, /* Some firmware revisions pad 4th hw address to 4 byte boundary making * it 8 bytes long in Native Wifi Rx decap. */ - ATH10K_FW_FEATURE_NO_NWIFI_DECAP_4ADDR_PADDING, + ATH10K_FW_FEATURE_NO_NWIFI_DECAP_4ADDR_PADDING = 8, /* Firmware supports bypassing PLL setting on init. */ ATH10K_FW_FEATURE_SUPPORTS_SKIP_CLOCK_INIT = 9, + /* Raw mode support. If supported, FW supports receiving and trasmitting + * frames in raw mode. + */ + ATH10K_FW_FEATURE_RAW_MODE_SUPPORT = 10, + /* keep last */ ATH10K_FW_FEATURE_COUNT, }; @@ -476,6 +481,15 @@ enum ath10k_dev_flags { * waiters should immediately cancel instead of waiting for a time out. */ ATH10K_FLAG_CRASH_FLUSH, + + /* Use Raw mode instead of native WiFi Tx/Rx encap mode. + * Raw mode supports both hardware and software crypto. Native WiFi only + * supports hardware crypto. + */ + ATH10K_FLAG_RAW_MODE, + + /* Disable HW crypto engine */ + ATH10K_FLAG_HW_CRYPTO_DISABLED, }; enum ath10k_cal_mode { @@ -484,6 +498,13 @@ enum ath10k_cal_mode { ATH10K_CAL_MODE_DT, }; +enum ath10k_crypt_mode { + /* Only use hardware crypto engine */ + ATH10K_CRYPT_MODE_HW, + /* Only use software crypto engine */ + ATH10K_CRYPT_MODE_SW, +}; + static inline const char *ath10k_cal_mode_str(enum ath10k_cal_mode mode) { switch (mode) { diff --git a/drivers/net/wireless/ath/ath10k/debug.c b/drivers/net/wireless/ath/ath10k/debug.c index edf6047997a7..1a33bf04b7b7 100644 --- a/drivers/net/wireless/ath/ath10k/debug.c +++ b/drivers/net/wireless/ath/ath10k/debug.c @@ -128,7 +128,7 @@ void ath10k_print_driver_info(struct ath10k *ar) ath10k_core_get_fw_features_str(ar, fw_features, sizeof(fw_features)); - ath10k_info(ar, "%s (0x%08x, 0x%08x%s%s%s) fw %s api %d htt-ver %d.%d wmi-op %d htt-op %d cal %s max-sta %d features %s\n", + ath10k_info(ar, "%s (0x%08x, 0x%08x%s%s%s) fw %s api %d htt-ver %d.%d wmi-op %d htt-op %d cal %s max-sta %d raw %d hwcrypto %d features %s\n", ar->hw_params.name, ar->target_version, ar->chip_id, @@ -144,6 +144,8 @@ void ath10k_print_driver_info(struct ath10k *ar) ar->htt.op_version, ath10k_cal_mode_str(ar->cal_mode), ar->max_num_stations, + test_bit(ATH10K_FLAG_RAW_MODE, &ar->dev_flags), + !test_bit(ATH10K_FLAG_HW_CRYPTO_DISABLED, &ar->dev_flags), fw_features); ath10k_info(ar, "debug %d debugfs %d tracing %d dfs %d testmode %d\n", config_enabled(CONFIG_ATH10K_DEBUG), @@ -1363,12 +1365,8 @@ static ssize_t ath10k_read_htt_max_amsdu_ampdu(struct file *file, mutex_lock(&ar->conf_mutex); - if (ar->debug.htt_max_amsdu) - amsdu = ar->debug.htt_max_amsdu; - - if (ar->debug.htt_max_ampdu) - ampdu = ar->debug.htt_max_ampdu; - + amsdu = ar->htt.max_num_amsdu; + ampdu = ar->htt.max_num_ampdu; mutex_unlock(&ar->conf_mutex); len = scnprintf(buf, sizeof(buf), "%u %u\n", amsdu, ampdu); @@ -1402,8 +1400,8 @@ static ssize_t ath10k_write_htt_max_amsdu_ampdu(struct file *file, goto out; res = count; - ar->debug.htt_max_amsdu = amsdu; - ar->debug.htt_max_ampdu = ampdu; + ar->htt.max_num_amsdu = amsdu; + ar->htt.max_num_ampdu = ampdu; out: mutex_unlock(&ar->conf_mutex); @@ -1905,9 +1903,6 @@ void ath10k_debug_stop(struct ath10k *ar) if (ar->debug.htt_stats_mask != 0) cancel_delayed_work(&ar->debug.htt_stats_dwork); - ar->debug.htt_max_amsdu = 0; - ar->debug.htt_max_ampdu = 0; - ath10k_wmi_pdev_pktlog_disable(ar); } diff --git a/drivers/net/wireless/ath/ath10k/htt.c b/drivers/net/wireless/ath/ath10k/htt.c index 4474c3e839db..3e6ba63dfdff 100644 --- a/drivers/net/wireless/ath/ath10k/htt.c +++ b/drivers/net/wireless/ath/ath10k/htt.c @@ -246,12 +246,31 @@ int ath10k_htt_setup(struct ath10k_htt *htt) } status = ath10k_htt_verify_version(htt); - if (status) + if (status) { + ath10k_warn(ar, "failed to verify htt version: %d\n", + status); return status; + } status = ath10k_htt_send_frag_desc_bank_cfg(htt); if (status) return status; - return ath10k_htt_send_rx_ring_cfg_ll(htt); + status = ath10k_htt_send_rx_ring_cfg_ll(htt); + if (status) { + ath10k_warn(ar, "failed to setup rx ring: %d\n", + status); + return status; + } + + status = ath10k_htt_h2t_aggr_cfg_msg(htt, + htt->max_num_ampdu, + htt->max_num_amsdu); + if (status) { + ath10k_warn(ar, "failed to setup amsdu/ampdu limit: %d\n", + status); + return status; + } + + return 0; } diff --git a/drivers/net/wireless/ath/ath10k/htt.h b/drivers/net/wireless/ath/ath10k/htt.h index 7583a126e879..573187512895 100644 --- a/drivers/net/wireless/ath/ath10k/htt.h +++ b/drivers/net/wireless/ath/ath10k/htt.h @@ -1396,6 +1396,8 @@ struct ath10k_htt { u8 target_version_minor; struct completion target_version_received; enum ath10k_fw_htt_op_version op_version; + u8 max_num_amsdu; + u8 max_num_ampdu; const enum htt_t2h_msg_type *t2h_msg_types; u32 t2h_msg_types_max; @@ -1558,6 +1560,12 @@ struct htt_rx_desc { #define HTT_LOG2_MAX_CACHE_LINE_SIZE 7 /* 2^7 = 128 */ #define HTT_MAX_CACHE_LINE_SIZE_MASK ((1 << HTT_LOG2_MAX_CACHE_LINE_SIZE) - 1) +/* These values are default in most firmware revisions and apparently are a + * sweet spot performance wise. + */ +#define ATH10K_HTT_MAX_NUM_AMSDU_DEFAULT 3 +#define ATH10K_HTT_MAX_NUM_AMPDU_DEFAULT 64 + int ath10k_htt_connect(struct ath10k_htt *htt); int ath10k_htt_init(struct ath10k *ar); int ath10k_htt_setup(struct ath10k_htt *htt); diff --git a/drivers/net/wireless/ath/ath10k/htt_rx.c b/drivers/net/wireless/ath/ath10k/htt_rx.c index 5e54c393767e..1b7a04366256 100644 --- a/drivers/net/wireless/ath/ath10k/htt_rx.c +++ b/drivers/net/wireless/ath/ath10k/htt_rx.c @@ -1017,9 +1017,8 @@ static void ath10k_htt_rx_h_undecap_raw(struct ath10k *ar, skb_trim(msdu, msdu->len - FCS_LEN); /* In most cases this will be true for sniffed frames. It makes sense - * to deliver them as-is without stripping the crypto param. This would - * also make sense for software based decryption (which is not - * implemented in ath10k). + * to deliver them as-is without stripping the crypto param. This is + * necessary for software based decryption. * * If there's no error then the frame is decrypted. At least that is * the case for frames that come in via fragmented rx indication. @@ -2066,6 +2065,8 @@ void ath10k_htt_t2h_msg_handler(struct ath10k *ar, struct sk_buff *skb) break; case HTT_T2H_MSG_TYPE_CHAN_CHANGE: break; + case HTT_T2H_MSG_TYPE_AGGR_CONF: + break; case HTT_T2H_MSG_TYPE_EN_STATS: case HTT_T2H_MSG_TYPE_TX_FETCH_IND: case HTT_T2H_MSG_TYPE_TX_FETCH_CONF: diff --git a/drivers/net/wireless/ath/ath10k/htt_tx.c b/drivers/net/wireless/ath/ath10k/htt_tx.c index 2c0627b7141b..81fd81f4df01 100644 --- a/drivers/net/wireless/ath/ath10k/htt_tx.c +++ b/drivers/net/wireless/ath/ath10k/htt_tx.c @@ -523,8 +523,12 @@ int ath10k_htt_tx(struct ath10k_htt *htt, struct sk_buff *msdu) if ((ieee80211_is_action(hdr->frame_control) || ieee80211_is_deauth(hdr->frame_control) || ieee80211_is_disassoc(hdr->frame_control)) && - ieee80211_has_protected(hdr->frame_control)) + ieee80211_has_protected(hdr->frame_control)) { skb_put(msdu, IEEE80211_CCMP_MIC_LEN); + } else if (!skb_cb->htt.nohwcrypt && + skb_cb->txmode == ATH10K_HW_TXRX_RAW) { + skb_put(msdu, IEEE80211_CCMP_MIC_LEN); + } skb_cb->paddr = dma_map_single(dev, msdu->data, msdu->len, DMA_TO_DEVICE); @@ -595,12 +599,16 @@ int ath10k_htt_tx(struct ath10k_htt *htt, struct sk_buff *msdu) prefetch_len); skb_cb->htt.txbuf->htc_hdr.flags = 0; + if (skb_cb->htt.nohwcrypt) + flags0 |= HTT_DATA_TX_DESC_FLAGS0_NO_ENCRYPT; + if (!skb_cb->is_protected) flags0 |= HTT_DATA_TX_DESC_FLAGS0_NO_ENCRYPT; flags1 |= SM((u16)vdev_id, HTT_DATA_TX_DESC_FLAGS1_VDEV_ID); flags1 |= SM((u16)tid, HTT_DATA_TX_DESC_FLAGS1_EXT_TID); - if (msdu->ip_summed == CHECKSUM_PARTIAL) { + if (msdu->ip_summed == CHECKSUM_PARTIAL && + !test_bit(ATH10K_FLAG_RAW_MODE, &ar->dev_flags)) { flags1 |= HTT_DATA_TX_DESC_FLAGS1_CKSUM_L3_OFFLOAD; flags1 |= HTT_DATA_TX_DESC_FLAGS1_CKSUM_L4_OFFLOAD; if (ar->hw_params.continuous_frag_desc) diff --git a/drivers/net/wireless/ath/ath10k/hw.h b/drivers/net/wireless/ath/ath10k/hw.h index 917228517546..7bfb9e276d17 100644 --- a/drivers/net/wireless/ath/ath10k/hw.h +++ b/drivers/net/wireless/ath/ath10k/hw.h @@ -217,14 +217,16 @@ void ath10k_hw_fill_survey_time(struct ath10k *ar, struct survey_info *survey, #define QCA_REV_99X0(ar) ((ar)->hw_rev == ATH10K_HW_QCA99X0) /* Known pecularities: - * - current FW doesn't support raw rx mode (last tested v599) - * - current FW dumps upon raw tx mode (last tested v599) * - raw appears in nwifi decap, raw and nwifi appear in ethernet decap * - raw have FCS, nwifi doesn't * - ethernet frames have 802.11 header decapped and parts (base hdr, cipher * param, llc/snap) are aligned to 4byte boundaries each */ enum ath10k_hw_txrx_mode { ATH10K_HW_TXRX_RAW = 0, + + /* Native Wifi decap mode is used to align IP frames to 4-byte + * boundaries and avoid a very expensive re-alignment in mac80211. + */ ATH10K_HW_TXRX_NATIVE_WIFI = 1, ATH10K_HW_TXRX_ETHERNET = 2, @@ -286,10 +288,6 @@ enum ath10k_hw_rate_cck { #define TARGET_RX_TIMEOUT_LO_PRI 100 #define TARGET_RX_TIMEOUT_HI_PRI 40 -/* Native Wifi decap mode is used to align IP frames to 4-byte boundaries and - * avoid a very expensive re-alignment in mac80211. */ -#define TARGET_RX_DECAP_MODE ATH10K_HW_TXRX_NATIVE_WIFI - #define TARGET_SCAN_MAX_PENDING_REQS 4 #define TARGET_BMISS_OFFLOAD_MAX_VDEV 3 #define TARGET_ROAM_OFFLOAD_MAX_VDEV 3 @@ -324,7 +322,6 @@ enum ath10k_hw_rate_cck { #define TARGET_10X_RX_CHAIN_MASK (BIT(0) | BIT(1) | BIT(2)) #define TARGET_10X_RX_TIMEOUT_LO_PRI 100 #define TARGET_10X_RX_TIMEOUT_HI_PRI 40 -#define TARGET_10X_RX_DECAP_MODE ATH10K_HW_TXRX_NATIVE_WIFI #define TARGET_10X_SCAN_MAX_PENDING_REQS 4 #define TARGET_10X_BMISS_OFFLOAD_MAX_VDEV 2 #define TARGET_10X_ROAM_OFFLOAD_MAX_VDEV 2 diff --git a/drivers/net/wireless/ath/ath10k/mac.c b/drivers/net/wireless/ath/ath10k/mac.c index 49a54a1f07a8..acd222f3b899 100644 --- a/drivers/net/wireless/ath/ath10k/mac.c +++ b/drivers/net/wireless/ath/ath10k/mac.c @@ -197,6 +197,10 @@ static int ath10k_send_key(struct ath10k_vif *arvif, return -EOPNOTSUPP; } + if (test_bit(ATH10K_FLAG_RAW_MODE, &ar->dev_flags)) { + key->flags |= IEEE80211_KEY_FLAG_GENERATE_IV; + } + if (cmd == DISABLE_KEY) { arg.key_cipher = WMI_CIPHER_NONE; arg.key_data = NULL; @@ -218,6 +222,9 @@ static int ath10k_install_key(struct ath10k_vif *arvif, reinit_completion(&ar->install_key_done); + if (arvif->nohwcrypt) + return 1; + ret = ath10k_send_key(arvif, key, cmd, macaddr, flags); if (ret) return ret; @@ -256,7 +263,7 @@ static int ath10k_install_peer_wep_keys(struct ath10k_vif *arvif, ret = ath10k_install_key(arvif, arvif->wep_keys[i], SET_KEY, addr, flags); - if (ret) + if (ret < 0) return ret; flags = 0; @@ -264,7 +271,7 @@ static int ath10k_install_peer_wep_keys(struct ath10k_vif *arvif, ret = ath10k_install_key(arvif, arvif->wep_keys[i], SET_KEY, addr, flags); - if (ret) + if (ret < 0) return ret; spin_lock_bh(&ar->data_lock); @@ -322,10 +329,10 @@ static int ath10k_clear_peer_keys(struct ath10k_vif *arvif, /* key flags are not required to delete the key */ ret = ath10k_install_key(arvif, peer->keys[i], DISABLE_KEY, addr, flags); - if (ret && first_errno == 0) + if (ret < 0 && first_errno == 0) first_errno = ret; - if (ret) + if (ret < 0) ath10k_warn(ar, "failed to remove peer wep key %d: %d\n", i, ret); @@ -398,7 +405,7 @@ static int ath10k_clear_vdev_key(struct ath10k_vif *arvif, break; /* key flags are not required to delete the key */ ret = ath10k_install_key(arvif, key, DISABLE_KEY, addr, flags); - if (ret && first_errno == 0) + if (ret < 0 && first_errno == 0) first_errno = ret; if (ret) @@ -3149,13 +3156,30 @@ ath10k_tx_h_get_txmode(struct ath10k *ar, struct ieee80211_vif *vif, * Some wmi-tlv firmwares for qca6174 have broken Tx key selection for * NativeWifi txmode - it selects AP key instead of peer key. It seems * to work with Ethernet txmode so use it. + * + * FIXME: Check if raw mode works with TDLS. */ if (ieee80211_is_data_present(fc) && sta && sta->tdls) return ATH10K_HW_TXRX_ETHERNET; + if (test_bit(ATH10K_FLAG_RAW_MODE, &ar->dev_flags)) + return ATH10K_HW_TXRX_RAW; + return ATH10K_HW_TXRX_NATIVE_WIFI; } +static bool ath10k_tx_h_use_hwcrypto(struct ieee80211_vif *vif, + struct sk_buff *skb) { + struct ieee80211_tx_info *info = IEEE80211_SKB_CB(skb); + const u32 mask = IEEE80211_TX_INTFL_DONT_ENCRYPT | + IEEE80211_TX_CTL_INJECTED; + if ((info->flags & mask) == mask) + return false; + if (vif) + return !ath10k_vif_to_arvif(vif)->nohwcrypt; + return true; +} + /* HTT Tx uses Native Wifi tx mode which expects 802.11 frames without QoS * Control in the header. */ @@ -3600,6 +3624,7 @@ static void ath10k_tx(struct ieee80211_hw *hw, ATH10K_SKB_CB(skb)->htt.is_offchan = false; ATH10K_SKB_CB(skb)->htt.freq = 0; ATH10K_SKB_CB(skb)->htt.tid = ath10k_tx_h_get_tid(hdr); + ATH10K_SKB_CB(skb)->htt.nohwcrypt = !ath10k_tx_h_use_hwcrypto(vif, skb); ATH10K_SKB_CB(skb)->vdev_id = ath10k_tx_h_get_vdev_id(ar, vif); ATH10K_SKB_CB(skb)->txmode = ath10k_tx_h_get_txmode(ar, vif, sta, skb); ATH10K_SKB_CB(skb)->is_protected = ieee80211_has_protected(fc); @@ -3615,12 +3640,11 @@ static void ath10k_tx(struct ieee80211_hw *hw, ath10k_tx_h_8023(skb); break; case ATH10K_HW_TXRX_RAW: - /* FIXME: Packet injection isn't implemented. It should be - * doable with firmware 10.2 on qca988x. - */ - WARN_ON_ONCE(1); - ieee80211_free_txskb(hw, skb); - return; + if (!test_bit(ATH10K_FLAG_RAW_MODE, &ar->dev_flags)) { + WARN_ON_ONCE(1); + ieee80211_free_txskb(hw, skb); + return; + } } if (info->flags & IEEE80211_TX_CTL_TX_OFFCHAN) { @@ -4139,6 +4163,14 @@ static int ath10k_add_interface(struct ieee80211_hw *hw, goto err; } } + if (test_bit(ATH10K_FLAG_HW_CRYPTO_DISABLED, &ar->dev_flags)) + arvif->nohwcrypt = true; + + if (arvif->nohwcrypt && + !test_bit(ATH10K_FLAG_RAW_MODE, &ar->dev_flags)) { + ath10k_warn(ar, "cryptmode module param needed for sw crypto\n"); + goto err; + } ath10k_dbg(ar, ATH10K_DBG_MAC, "mac vdev create %d (add interface) type %d subtype %d bcnmode %s\n", arvif->vdev_id, arvif->vdev_type, arvif->vdev_subtype, @@ -4728,6 +4760,9 @@ static int ath10k_set_key(struct ieee80211_hw *hw, enum set_key_cmd cmd, if (key->cipher == WLAN_CIPHER_SUITE_AES_CMAC) return 1; + if (arvif->nohwcrypt) + return 1; + if (key->keyidx > WMI_MAX_KEY_INDEX) return -ENOSPC; @@ -4797,6 +4832,7 @@ static int ath10k_set_key(struct ieee80211_hw *hw, enum set_key_cmd cmd, ret = ath10k_install_key(arvif, key, cmd, peer_addr, flags); if (ret) { + WARN_ON(ret > 0); ath10k_warn(ar, "failed to install key for vdev %i peer %pM: %d\n", arvif->vdev_id, peer_addr, ret); goto exit; @@ -4812,13 +4848,16 @@ static int ath10k_set_key(struct ieee80211_hw *hw, enum set_key_cmd cmd, ret = ath10k_install_key(arvif, key, cmd, peer_addr, flags2); if (ret) { + WARN_ON(ret > 0); ath10k_warn(ar, "failed to install (ucast) key for vdev %i peer %pM: %d\n", arvif->vdev_id, peer_addr, ret); ret2 = ath10k_install_key(arvif, key, DISABLE_KEY, peer_addr, flags); - if (ret2) + if (ret2) { + WARN_ON(ret2 > 0); ath10k_warn(ar, "failed to disable (mcast) key for vdev %i peer %pM: %d\n", arvif->vdev_id, peer_addr, ret2); + } goto exit; } } @@ -6892,7 +6931,6 @@ int ath10k_mac_register(struct ath10k *ar) ieee80211_hw_set(ar->hw, HAS_RATE_CONTROL); ieee80211_hw_set(ar->hw, AP_LINK_PS); ieee80211_hw_set(ar->hw, SPECTRUM_MGMT); - ieee80211_hw_set(ar->hw, SW_CRYPTO_CONTROL); ieee80211_hw_set(ar->hw, SUPPORT_FAST_XMIT); ieee80211_hw_set(ar->hw, CONNECTION_MONITOR); ieee80211_hw_set(ar->hw, SUPPORTS_PER_STA_GTK); @@ -6900,6 +6938,9 @@ int ath10k_mac_register(struct ath10k *ar) ieee80211_hw_set(ar->hw, CHANCTX_STA_CSA); ieee80211_hw_set(ar->hw, QUEUE_CONTROL); + if (!test_bit(ATH10K_FLAG_RAW_MODE, &ar->dev_flags)) + ieee80211_hw_set(ar->hw, SW_CRYPTO_CONTROL); + ar->hw->wiphy->features |= NL80211_FEATURE_STATIC_SMPS; ar->hw->wiphy->flags |= WIPHY_FLAG_IBSS_RSN; @@ -7003,7 +7044,8 @@ int ath10k_mac_register(struct ath10k *ar) goto err_free; } - ar->hw->netdev_features = NETIF_F_HW_CSUM; + if (!test_bit(ATH10K_FLAG_RAW_MODE, &ar->dev_flags)) + ar->hw->netdev_features = NETIF_F_HW_CSUM; if (config_enabled(CONFIG_ATH10K_DFS_CERTIFIED)) { /* Init ath dfs pattern detector */ diff --git a/drivers/net/wireless/ath/ath10k/wmi-tlv.c b/drivers/net/wireless/ath/ath10k/wmi-tlv.c index 4189d4a90ce0..34fbc8fddb72 100644 --- a/drivers/net/wireless/ath/ath10k/wmi-tlv.c +++ b/drivers/net/wireless/ath/ath10k/wmi-tlv.c @@ -1373,7 +1373,7 @@ static struct sk_buff *ath10k_wmi_tlv_op_gen_init(struct ath10k *ar) cfg->rx_timeout_pri[1] = __cpu_to_le32(0x64); cfg->rx_timeout_pri[2] = __cpu_to_le32(0x64); cfg->rx_timeout_pri[3] = __cpu_to_le32(0x28); - cfg->rx_decap_mode = __cpu_to_le32(1); + cfg->rx_decap_mode = __cpu_to_le32(ar->wmi.rx_decap_mode); cfg->scan_max_pending_reqs = __cpu_to_le32(4); cfg->bmiss_offload_max_vdev = __cpu_to_le32(TARGET_TLV_NUM_VDEVS); cfg->roam_offload_max_vdev = __cpu_to_le32(TARGET_TLV_NUM_VDEVS); diff --git a/drivers/net/wireless/ath/ath10k/wmi.c b/drivers/net/wireless/ath/ath10k/wmi.c index 1435614b0a55..3d46813b9beb 100644 --- a/drivers/net/wireless/ath/ath10k/wmi.c +++ b/drivers/net/wireless/ath/ath10k/wmi.c @@ -4688,8 +4688,7 @@ static struct sk_buff *ath10k_wmi_op_gen_init(struct ath10k *ar) config.rx_timeout_pri_vi = __cpu_to_le32(TARGET_RX_TIMEOUT_LO_PRI); config.rx_timeout_pri_be = __cpu_to_le32(TARGET_RX_TIMEOUT_LO_PRI); config.rx_timeout_pri_bk = __cpu_to_le32(TARGET_RX_TIMEOUT_HI_PRI); - config.rx_decap_mode = __cpu_to_le32(TARGET_RX_DECAP_MODE); - + config.rx_decap_mode = __cpu_to_le32(ar->wmi.rx_decap_mode); config.scan_max_pending_reqs = __cpu_to_le32(TARGET_SCAN_MAX_PENDING_REQS); @@ -4757,8 +4756,7 @@ static struct sk_buff *ath10k_wmi_10_1_op_gen_init(struct ath10k *ar) config.rx_timeout_pri_vi = __cpu_to_le32(TARGET_10X_RX_TIMEOUT_LO_PRI); config.rx_timeout_pri_be = __cpu_to_le32(TARGET_10X_RX_TIMEOUT_LO_PRI); config.rx_timeout_pri_bk = __cpu_to_le32(TARGET_10X_RX_TIMEOUT_HI_PRI); - config.rx_decap_mode = __cpu_to_le32(TARGET_10X_RX_DECAP_MODE); - + config.rx_decap_mode = __cpu_to_le32(ar->wmi.rx_decap_mode); config.scan_max_pending_reqs = __cpu_to_le32(TARGET_10X_SCAN_MAX_PENDING_REQS); @@ -4823,7 +4821,7 @@ static struct sk_buff *ath10k_wmi_10_2_op_gen_init(struct ath10k *ar) config.rx_timeout_pri_vi = __cpu_to_le32(TARGET_10X_RX_TIMEOUT_LO_PRI); config.rx_timeout_pri_be = __cpu_to_le32(TARGET_10X_RX_TIMEOUT_LO_PRI); config.rx_timeout_pri_bk = __cpu_to_le32(TARGET_10X_RX_TIMEOUT_HI_PRI); - config.rx_decap_mode = __cpu_to_le32(TARGET_10X_RX_DECAP_MODE); + config.rx_decap_mode = __cpu_to_le32(ar->wmi.rx_decap_mode); config.scan_max_pending_reqs = __cpu_to_le32(TARGET_10X_SCAN_MAX_PENDING_REQS); -- 2.20.1