From b3c195b3a75b0aff9ede850ba2208cd1f40a702b Mon Sep 17 00:00:00 2001 From: Stefan Roese Date: Thu, 19 May 2016 09:07:05 +0200 Subject: [PATCH] spi: orion: Add direct access mode This patch adds support for the direct access mode to the Orion SPI driver which is used on the Marvell Armada based SoCs. In this direct mode, all data written to (or read from) a specifically mapped MBus window (linked to one SPI chip-select on one of the SPI controllers) will be transferred directly to the SPI bus. Without the need to control the SPI registers in between. This can improve the SPI transfer rate in such cases. Both, direct-read and -write mode are supported. But only the write mode has been tested. This mode especially benefits from the SPI direct mode, as the data bytes are written head-to-head to the SPI bus, without any additional addresses. One use-case for this direct write mode is, programming a FPGA bitstream image into the FPGA connected to the SPI bus at maximum speed. This mode is described in chapter "22.5.2 Direct Write to SPI" in the Marvell Armada XP Functional Spec Datasheet. Signed-off-by: Stefan Roese Acked-by: Arnd Bergmann Signed-off-by: Mark Brown --- .../devicetree/bindings/spi/spi-orion.txt | 49 ++++++++++- drivers/spi/spi-orion.c | 88 +++++++++++++++++++ 2 files changed, 136 insertions(+), 1 deletion(-) diff --git a/Documentation/devicetree/bindings/spi/spi-orion.txt b/Documentation/devicetree/bindings/spi/spi-orion.txt index 98bc69815eb3..4f629cc7634a 100644 --- a/Documentation/devicetree/bindings/spi/spi-orion.txt +++ b/Documentation/devicetree/bindings/spi/spi-orion.txt @@ -8,7 +8,15 @@ Required properties: - "marvell,armada-380-spi", for the Armada 38x SoCs - "marvell,armada-390-spi", for the Armada 39x SoCs - "marvell,armada-xp-spi", for the Armada XP SoCs -- reg : offset and length of the register set for the device +- reg : offset and length of the register set for the device. + This property can optionally have additional entries to configure + the SPI direct access mode that some of the Marvell SoCs support + additionally to the normal indirect access (PIO) mode. The values + for the MBus "target" and "attribute" are defined in the Marvell + SoC "Functional Specifications" Manual in the chapter "Marvell + Core Processor Address Decoding". + The eight register sets following the control registers refer to + chip-select lines 0 through 7 respectively. - cell-index : Which of multiple SPI controllers is this. Optional properties: - interrupts : Is currently not used. @@ -23,3 +31,42 @@ Example: interrupts = <23>; status = "disabled"; }; + +Example with SPI direct mode support (optionally): + spi0: spi@10600 { + compatible = "marvell,orion-spi"; + #address-cells = <1>; + #size-cells = <0>; + cell-index = <0>; + reg = , /* control */ + , /* CS0 */ + , /* CS1 */ + , /* CS2 */ + , /* CS3 */ + , /* CS4 */ + , /* CS5 */ + , /* CS6 */ + ; /* CS7 */ + interrupts = <23>; + status = "disabled"; + }; + +To enable the direct mode, the board specific 'ranges' property in the +'soc' node needs to add the entries for the desired SPI controllers +and its chip-selects that are used in the direct mode instead of PIO +mode. Here an example for this (SPI controller 0, device 1 and SPI +controller 1, device 2 are used in direct mode. All other SPI device +are used in the default indirect (PIO) mode): + soc { + /* + * Enable the SPI direct access by configuring an entry + * here in the board-specific ranges property + */ + ranges = , /* internal regs */ + , /* BootROM */ + , /* SPI0-DEV1 */ + ; /* SPI1-DEV2 */ + +For further information on the MBus bindings, please see the MBus +DT documentation: +Documentation/devicetree/bindings/bus/mvebu-mbus.txt diff --git a/drivers/spi/spi-orion.c b/drivers/spi/spi-orion.c index a87cfd4ba17b..d0d9c8682b32 100644 --- a/drivers/spi/spi-orion.c +++ b/drivers/spi/spi-orion.c @@ -18,6 +18,7 @@ #include #include #include +#include #include #include #include @@ -43,6 +44,9 @@ #define ORION_SPI_INT_CAUSE_REG 0x10 #define ORION_SPI_TIMING_PARAMS_REG 0x18 +/* Register for the "Direct Mode" */ +#define SPI_DIRECT_WRITE_CONFIG_REG 0x20 + #define ORION_SPI_TMISO_SAMPLE_MASK (0x3 << 6) #define ORION_SPI_TMISO_SAMPLE_1 (1 << 6) #define ORION_SPI_TMISO_SAMPLE_2 (2 << 6) @@ -78,11 +82,18 @@ struct orion_spi_dev { bool is_errata_50mhz_ac; }; +struct orion_direct_acc { + void __iomem *vaddr; + u32 size; +}; + struct orion_spi { struct spi_master *master; void __iomem *base; struct clk *clk; const struct orion_spi_dev *devdata; + + struct orion_direct_acc direct_access[ORION_NUM_CHIPSELECTS]; }; static inline void __iomem *spi_reg(struct orion_spi *orion_spi, u32 reg) @@ -372,10 +383,39 @@ orion_spi_write_read(struct spi_device *spi, struct spi_transfer *xfer) { unsigned int count; int word_len; + struct orion_spi *orion_spi; + int cs = spi->chip_select; word_len = spi->bits_per_word; count = xfer->len; + orion_spi = spi_master_get_devdata(spi->master); + + /* + * Use SPI direct write mode if base address is available. Otherwise + * fall back to PIO mode for this transfer. + */ + if ((orion_spi->direct_access[cs].vaddr) && (xfer->tx_buf) && + (word_len == 8)) { + unsigned int cnt = count / 4; + unsigned int rem = count % 4; + + /* + * Send the TX-data to the SPI device via the direct + * mapped address window + */ + iowrite32_rep(orion_spi->direct_access[cs].vaddr, + xfer->tx_buf, cnt); + if (rem) { + u32 *buf = (u32 *)xfer->tx_buf; + + iowrite8_rep(orion_spi->direct_access[cs].vaddr, + &buf[cnt], rem); + } + + return count; + } + if (word_len == 8) { const u8 *tx = xfer->tx_buf; u8 *rx = xfer->rx_buf; @@ -425,6 +465,10 @@ static int orion_spi_reset(struct orion_spi *orion_spi) { /* Verify that the CS is deasserted */ orion_spi_clrbits(orion_spi, ORION_SPI_IF_CTRL_REG, 0x1); + + /* Don't deassert CS between the direct mapped SPI transfers */ + writel(0, spi_reg(orion_spi, SPI_DIRECT_WRITE_CONFIG_REG)); + return 0; } @@ -504,6 +548,7 @@ static int orion_spi_probe(struct platform_device *pdev) struct resource *r; unsigned long tclk_hz; int status = 0; + struct device_node *np; master = spi_alloc_master(&pdev->dev, sizeof(*spi)); if (master == NULL) { @@ -576,6 +621,49 @@ static int orion_spi_probe(struct platform_device *pdev) goto out_rel_clk; } + /* Scan all SPI devices of this controller for direct mapped devices */ + for_each_available_child_of_node(pdev->dev.of_node, np) { + u32 cs; + + /* Get chip-select number from the "reg" property */ + status = of_property_read_u32(np, "reg", &cs); + if (status) { + dev_err(&pdev->dev, + "%s has no valid 'reg' property (%d)\n", + np->full_name, status); + status = 0; + continue; + } + + /* + * Check if an address is configured for this SPI device. If + * not, the MBus mapping via the 'ranges' property in the 'soc' + * node is not configured and this device should not use the + * direct mode. In this case, just continue with the next + * device. + */ + status = of_address_to_resource(pdev->dev.of_node, cs + 1, r); + if (status) + continue; + + /* + * Only map one page for direct access. This is enough for the + * simple TX transfer which only writes to the first word. + * This needs to get extended for the direct SPI-NOR / SPI-NAND + * support, once this gets implemented. + */ + spi->direct_access[cs].vaddr = devm_ioremap(&pdev->dev, + r->start, + PAGE_SIZE); + if (IS_ERR(spi->direct_access[cs].vaddr)) { + status = PTR_ERR(spi->direct_access[cs].vaddr); + goto out_rel_clk; + } + spi->direct_access[cs].size = PAGE_SIZE; + + dev_info(&pdev->dev, "CS%d configured for direct access\n", cs); + } + pm_runtime_set_active(&pdev->dev); pm_runtime_use_autosuspend(&pdev->dev); pm_runtime_set_autosuspend_delay(&pdev->dev, SPI_AUTOSUSPEND_TIMEOUT); -- 2.20.1