From ad4a6ebeffd2767bdcdec9e1acea7ffc00d5be2d Mon Sep 17 00:00:00 2001 From: Masanari Iida Date: Wed, 25 Feb 2015 20:30:22 +0900 Subject: [PATCH] doc/input : Fix typos in Documentation/input This patch fix spelling typos in Documentations/input. Signed-off-by: Masanari Iida Acked-by: Randy Dunlap Signed-off-by: Jonathan Corbet --- Documentation/input/alps.txt | 4 ++-- Documentation/input/event-codes.txt | 2 +- Documentation/input/gpio-tilt.txt | 2 +- Documentation/input/iforce-protocol.txt | 2 +- Documentation/input/walkera0701.txt | 2 +- Documentation/input/yealink.txt | 2 +- 6 files changed, 7 insertions(+), 7 deletions(-) diff --git a/Documentation/input/alps.txt b/Documentation/input/alps.txt index a63e5e013a8c..b9ecf9965b4c 100644 --- a/Documentation/input/alps.txt +++ b/Documentation/input/alps.txt @@ -58,7 +58,7 @@ To exit command mode, PSMOUSE_CMD_SETSTREAM (EA) is sent to the touchpad. While in command mode, register addresses can be set by first sending a specific command, either EC for v3 devices or F5 for v4 devices. Then the address is sent one nibble at a time, where each nibble is encoded as a -command with optional data. This enoding differs slightly between the v3 and +command with optional data. This encoding differs slightly between the v3 and v4 protocols. Once an address has been set, the addressed register can be read by sending @@ -131,7 +131,7 @@ ALPS Absolute Mode - Protocol Version 3 --------------------------------------- ALPS protocol version 3 has three different packet formats. The first two are -associated with touchpad events, and the third is associatd with trackstick +associated with touchpad events, and the third is associated with trackstick events. The first type is the touchpad position packet. diff --git a/Documentation/input/event-codes.txt b/Documentation/input/event-codes.txt index c587a966413e..d92eae36b43a 100644 --- a/Documentation/input/event-codes.txt +++ b/Documentation/input/event-codes.txt @@ -229,7 +229,7 @@ such device to feedback. EV_PWR: ---------- EV_PWR events are a special type of event used specifically for power -mangement. Its usage is not well defined. To be addressed later. +management. Its usage is not well defined. To be addressed later. Device properties: ================= diff --git a/Documentation/input/gpio-tilt.txt b/Documentation/input/gpio-tilt.txt index 06d60c3ff5e7..2cdfd9bcb1af 100644 --- a/Documentation/input/gpio-tilt.txt +++ b/Documentation/input/gpio-tilt.txt @@ -28,7 +28,7 @@ Example: -------- Example configuration for a single TS1003 tilt switch that rotates around -one axis in 4 steps and emitts the current tilt via two GPIOs. +one axis in 4 steps and emits the current tilt via two GPIOs. static int sg060_tilt_enable(struct device *dev) { /* code to enable the sensors */ diff --git a/Documentation/input/iforce-protocol.txt b/Documentation/input/iforce-protocol.txt index 2d5fbfd6023e..66287151c54a 100644 --- a/Documentation/input/iforce-protocol.txt +++ b/Documentation/input/iforce-protocol.txt @@ -97,7 +97,7 @@ LEN= 0e *** Attack and fade *** OP= 02 LEN= 08 -00-01 Address where to store the parameteres +00-01 Address where to store the parameters 02-03 Duration of attack (little endian encoding, in ms) 04 Level at end of attack. Signed byte. 05-06 Duration of fade. diff --git a/Documentation/input/walkera0701.txt b/Documentation/input/walkera0701.txt index 561385d38482..49e3ac60dcef 100644 --- a/Documentation/input/walkera0701.txt +++ b/Documentation/input/walkera0701.txt @@ -91,7 +91,7 @@ absolute binary value. (10 bits per channel). Next nibble is checksum for first ten nibbles. Next nibbles 12 .. 21 represents four channels (not all channels can be -directly controlled from TX). Binary representations ar the same as in first +directly controlled from TX). Binary representations are the same as in first four channels. In nibbles 22 and 23 is a special magic number. Nibble 24 is checksum for nibbles 12..23. diff --git a/Documentation/input/yealink.txt b/Documentation/input/yealink.txt index 5360e434486c..8277b76ec506 100644 --- a/Documentation/input/yealink.txt +++ b/Documentation/input/yealink.txt @@ -93,7 +93,7 @@ Format description: Format specifier '8' : Generic 7 segment digit with individual addressable segments - Reduced capability 7 segm digit, when segments are hard wired together. + Reduced capability 7 segment digit, when segments are hard wired together. '1' : 2 segments digit only able to produce a 1. 'e' : Most significant day of the month digit, able to produce at least 1 2 3. -- 2.20.1