From a6c42322722976ca81e6d02e4a702f33d659d8fc Mon Sep 17 00:00:00 2001 From: Jesse Brandeburg Date: Wed, 25 Mar 2009 21:59:22 +0000 Subject: [PATCH] e1000: fix close race with interrupt this is in regards to http://bugzilla.kernel.org/show_bug.cgi?id=12876 where it appears that e1000 can leave its interrupt enabled after exiting the driver. Fix the bug by making the interrupt enable paths more aware of the driver exiting. Thanks to Alan Cox for the poke and initial investigation. CC: Alan Cox Signed-off-by: Jesse Brandeburg Signed-off-by: Jeff Kirsher Signed-off-by: David S. Miller --- drivers/net/e1000/e1000_main.c | 28 ++++++++++++++++++++++++---- 1 file changed, 24 insertions(+), 4 deletions(-) diff --git a/drivers/net/e1000/e1000_main.c b/drivers/net/e1000/e1000_main.c index 5c61b921ca71..93b861d032b5 100644 --- a/drivers/net/e1000/e1000_main.c +++ b/drivers/net/e1000/e1000_main.c @@ -577,12 +577,30 @@ out: void e1000_down(struct e1000_adapter *adapter) { + struct e1000_hw *hw = &adapter->hw; struct net_device *netdev = adapter->netdev; + u32 rctl, tctl; /* signal that we're down so the interrupt handler does not * reschedule our watchdog timer */ set_bit(__E1000_DOWN, &adapter->flags); + /* disable receives in the hardware */ + rctl = er32(RCTL); + ew32(RCTL, rctl & ~E1000_RCTL_EN); + /* flush and sleep below */ + + /* can be netif_tx_disable when NETIF_F_LLTX is removed */ + netif_stop_queue(netdev); + + /* disable transmits in the hardware */ + tctl = er32(TCTL); + tctl &= ~E1000_TCTL_EN; + ew32(TCTL, tctl); + /* flush both disables and wait for them to finish */ + E1000_WRITE_FLUSH(); + msleep(10); + napi_disable(&adapter->napi); e1000_irq_disable(adapter); @@ -595,7 +613,6 @@ void e1000_down(struct e1000_adapter *adapter) adapter->link_speed = 0; adapter->link_duplex = 0; netif_carrier_off(netdev); - netif_stop_queue(netdev); e1000_reset(adapter); e1000_clean_all_tx_rings(adapter); @@ -3744,10 +3761,12 @@ static irqreturn_t e1000_intr(int irq, void *data) adapter->total_rx_bytes = 0; adapter->total_rx_packets = 0; __napi_schedule(&adapter->napi); - } else + } else { /* this really should not happen! if it does it is basically a * bug, but not a hard error, so enable ints and continue */ - e1000_irq_enable(adapter); + if (!test_bit(__E1000_DOWN, &adapter->flags)) + e1000_irq_enable(adapter); + } return IRQ_HANDLED; } @@ -3777,7 +3796,8 @@ static int e1000_clean(struct napi_struct *napi, int budget) if (likely(adapter->itr_setting & 3)) e1000_set_itr(adapter); napi_complete(napi); - e1000_irq_enable(adapter); + if (!test_bit(__E1000_DOWN, &adapter->flags)) + e1000_irq_enable(adapter); } return work_done; -- 2.20.1