From a129be84ba83b964dde784e87820b89d1a7d29c3 Mon Sep 17 00:00:00 2001 From: Mark Einon Date: Fri, 4 Jan 2013 22:25:46 +0000 Subject: [PATCH] staging: et131x: Use register defines instead of magic numbers Use register name defines instead of magic numbers where a bit of clarity would be useful. Also a small typo fix and some register prefixes added, for further clarity. Signed-off-by: Mark Einon Signed-off-by: Greg Kroah-Hartman --- drivers/staging/et131x/et131x.c | 132 ++++++++++++++++++-------------- drivers/staging/et131x/et131x.h | 88 +++++++++++++++------ 2 files changed, 139 insertions(+), 81 deletions(-) diff --git a/drivers/staging/et131x/et131x.c b/drivers/staging/et131x/et131x.c index b08dff95923..e2d555529c6 100644 --- a/drivers/staging/et131x/et131x.c +++ b/drivers/staging/et131x/et131x.c @@ -344,6 +344,10 @@ struct rx_ring { * 14: UDP checksum assist */ +#define TXDESC_FLAG_LASTPKT 0x0001 +#define TXDESC_FLAG_FIRSTPKT 0x0002 +#define TXDESC_FLAG_INTPROC 0x0004 + /* struct tx_desc represents each descriptor on the ring */ struct tx_desc { u32 addr_hi; @@ -774,13 +778,12 @@ static int et131x_init_eeprom(struct et131x_adapter *adapter) /* We first need to check the EEPROM Status code located at offset * 0xB2 of config space */ - pci_read_config_byte(pdev, ET1310_PCI_EEPROM_STATUS, - &eestatus); + pci_read_config_byte(pdev, ET1310_PCI_EEPROM_STATUS, &eestatus); /* THIS IS A WORKAROUND: * I need to call this function twice to get my card in a * LG M1 Express Dual running. I tried also a msleep before this - * function, because I thought there could be some time condidions + * function, because I thought there could be some time conditions * but it didn't work. Call the whole function twice also work. */ if (pci_read_config_byte(pdev, ET1310_PCI_EEPROM_STATUS, &eestatus)) { @@ -932,7 +935,10 @@ static void et1310_config_mac_regs1(struct et131x_adapter *adapter) /* First we need to reset everything. Write to MAC configuration * register 1 to perform reset. */ - writel(0xC00F0000, ¯egs->cfg1); + writel(ET_MAC_CFG1_SOFT_RESET | ET_MAC_CFG1_SIM_RESET | + ET_MAC_CFG1_RESET_RXMC | ET_MAC_CFG1_RESET_TXMC | + ET_MAC_CFG1_RESET_RXFUNC | ET_MAC_CFG1_RESET_TXFUNC, + ¯egs->cfg1); /* Next lets configure the MAC Inter-packet gap register */ ipg = 0x38005860; /* IPG1 0x38 IPG2 0x58 B2B 0x60 */ @@ -947,7 +953,7 @@ static void et1310_config_mac_regs1(struct et131x_adapter *adapter) writel(0, ¯egs->if_ctrl); /* Let's move on to setting up the mii management configuration */ - writel(0x07, ¯egs->mii_mgmt_cfg); /* Clock reset 0x7 */ + writel(ET_MAC_MIIMGMT_CLK_RST, ¯egs->mii_mgmt_cfg); /* Next lets configure the MAC Station Address register. These * values are read from the EEPROM during initialization and stored @@ -998,38 +1004,43 @@ static void et1310_config_mac_regs2(struct et131x_adapter *adapter) ifctrl = readl(&mac->if_ctrl); /* Set up the if mode bits */ - cfg2 &= ~0x300; + cfg2 &= ~ET_MAC_CFG2_IFMODE_MASK; if (phydev && phydev->speed == SPEED_1000) { - cfg2 |= 0x200; + cfg2 |= ET_MAC_CFG2_IFMODE_1000; /* Phy mode bit */ - ifctrl &= ~(1 << 24); + ifctrl &= ~ET_MAC_IFCTRL_PHYMODE; } else { - cfg2 |= 0x100; - ifctrl |= (1 << 24); + cfg2 |= ET_MAC_CFG2_IFMODE_100; + ifctrl |= ET_MAC_IFCTRL_PHYMODE; } /* We need to enable Rx/Tx */ - cfg1 |= CFG1_RX_ENABLE | CFG1_TX_ENABLE | CFG1_TX_FLOW; + cfg1 |= ET_MAC_CFG1_RX_ENABLE | ET_MAC_CFG1_TX_ENABLE | + ET_MAC_CFG1_TX_FLOW; /* Initialize loop back to off */ - cfg1 &= ~(CFG1_LOOPBACK | CFG1_RX_FLOW); + cfg1 &= ~(ET_MAC_CFG1_LOOPBACK | ET_MAC_CFG1_RX_FLOW); if (adapter->flowcontrol == FLOW_RXONLY || adapter->flowcontrol == FLOW_BOTH) - cfg1 |= CFG1_RX_FLOW; + cfg1 |= ET_MAC_CFG1_RX_FLOW; writel(cfg1, &mac->cfg1); /* Now we need to initialize the MAC Configuration 2 register */ /* preamble 7, check length, huge frame off, pad crc, crc enable full duplex off */ - cfg2 |= 0x7016; - cfg2 &= ~0x0021; + cfg2 |= 0x7 << ET_MAC_CFG2_PREAMBLE_SHIFT; + cfg2 |= ET_MAC_CFG2_IFMODE_LEN_CHECK; + cfg2 |= ET_MAC_CFG2_IFMODE_PAD_CRC; + cfg2 |= ET_MAC_CFG2_IFMODE_CRC_ENABLE; + cfg2 &= ~ET_MAC_CFG2_IFMODE_HUGE_FRAME; + cfg2 &= ~ET_MAC_CFG2_IFMODE_FULL_DPLX; /* Turn on duplex if needed */ if (phydev && phydev->duplex == DUPLEX_FULL) - cfg2 |= 0x01; + cfg2 |= ET_MAC_CFG2_IFMODE_FULL_DPLX; - ifctrl &= ~(1 << 26); + ifctrl &= ~ET_MAC_IFCTRL_GHDMODE; if (phydev && phydev->duplex == DUPLEX_HALF) - ifctrl |= (1<<26); /* Enable ghd */ + ifctrl |= ET_MAC_IFCTRL_GHDMODE; writel(ifctrl, &mac->if_ctrl); writel(cfg2, &mac->cfg2); @@ -1038,7 +1049,7 @@ static void et1310_config_mac_regs2(struct et131x_adapter *adapter) udelay(10); delay++; cfg1 = readl(&mac->cfg1); - } while ((cfg1 & CFG1_WAIT) != CFG1_WAIT && delay < 100); + } while ((cfg1 & ET_MAC_CFG1_WAIT) != ET_MAC_CFG1_WAIT && delay < 100); if (delay == 100) { dev_warn(&adapter->pdev->dev, @@ -1047,7 +1058,7 @@ static void et1310_config_mac_regs2(struct et131x_adapter *adapter) } /* Enable txmac */ - ctl |= 0x09; /* TX mac enable, FC disable */ + ctl |= ET_TX_CTRL_TXMAC_ENABLE | ET_TX_CTRL_FC_DISABLE; writel(ctl, &adapter->regs->txmac.ctl); /* Ready to start the RXDMA/TXDMA engine */ @@ -1139,19 +1150,19 @@ static void et1310_setup_device_for_unicast(struct et131x_adapter *adapter) * Set up unicast packet filter reg 3 to be the octets 2 - 5 of the * MAC address for first address */ - uni_pf3 = (adapter->addr[0] << ET_UNI_PF_ADDR2_1_SHIFT) | - (adapter->addr[1] << ET_UNI_PF_ADDR2_2_SHIFT) | - (adapter->addr[0] << ET_UNI_PF_ADDR1_1_SHIFT) | + uni_pf3 = (adapter->addr[0] << ET_RX_UNI_PF_ADDR2_1_SHIFT) | + (adapter->addr[1] << ET_RX_UNI_PF_ADDR2_2_SHIFT) | + (adapter->addr[0] << ET_RX_UNI_PF_ADDR1_1_SHIFT) | adapter->addr[1]; - uni_pf2 = (adapter->addr[2] << ET_UNI_PF_ADDR2_3_SHIFT) | - (adapter->addr[3] << ET_UNI_PF_ADDR2_4_SHIFT) | - (adapter->addr[4] << ET_UNI_PF_ADDR2_5_SHIFT) | + uni_pf2 = (adapter->addr[2] << ET_RX_UNI_PF_ADDR2_3_SHIFT) | + (adapter->addr[3] << ET_RX_UNI_PF_ADDR2_4_SHIFT) | + (adapter->addr[4] << ET_RX_UNI_PF_ADDR2_5_SHIFT) | adapter->addr[5]; - uni_pf1 = (adapter->addr[2] << ET_UNI_PF_ADDR1_3_SHIFT) | - (adapter->addr[3] << ET_UNI_PF_ADDR1_4_SHIFT) | - (adapter->addr[4] << ET_UNI_PF_ADDR1_5_SHIFT) | + uni_pf1 = (adapter->addr[2] << ET_RX_UNI_PF_ADDR1_3_SHIFT) | + (adapter->addr[3] << ET_RX_UNI_PF_ADDR1_4_SHIFT) | + (adapter->addr[4] << ET_RX_UNI_PF_ADDR1_5_SHIFT) | adapter->addr[5]; pm_csr = readl(&adapter->regs->global.pm_csr); @@ -1208,13 +1219,13 @@ static void et1310_config_rxmac_regs(struct et131x_adapter *adapter) writel(0, &rxmac->mask4_word3); /* Lets setup the WOL Source Address */ - sa_lo = (adapter->addr[2] << ET_WOL_LO_SA3_SHIFT) | - (adapter->addr[3] << ET_WOL_LO_SA4_SHIFT) | - (adapter->addr[4] << ET_WOL_LO_SA5_SHIFT) | + sa_lo = (adapter->addr[2] << ET_RX_WOL_LO_SA3_SHIFT) | + (adapter->addr[3] << ET_RX_WOL_LO_SA4_SHIFT) | + (adapter->addr[4] << ET_RX_WOL_LO_SA5_SHIFT) | adapter->addr[5]; writel(sa_lo, &rxmac->sa_lo); - sa_hi = (u32) (adapter->addr[0] << ET_WOL_HI_SA1_SHIFT) | + sa_hi = (u32) (adapter->addr[0] << ET_RX_WOL_HI_SA1_SHIFT) | adapter->addr[1]; writel(sa_hi, &rxmac->sa_hi); @@ -1224,7 +1235,7 @@ static void et1310_config_rxmac_regs(struct et131x_adapter *adapter) /* Let's initialize the Unicast Packet filtering address */ if (adapter->packet_filter & ET131X_PACKET_TYPE_DIRECTED) { et1310_setup_device_for_unicast(adapter); - pf_ctrl |= 4; /* Unicast filter */ + pf_ctrl |= ET_RX_PFCTRL_UNICST_FILTER_ENABLE; } else { writel(0, &rxmac->uni_pf_addr1); writel(0, &rxmac->uni_pf_addr2); @@ -1233,13 +1244,13 @@ static void et1310_config_rxmac_regs(struct et131x_adapter *adapter) /* Let's initialize the Multicast hash */ if (!(adapter->packet_filter & ET131X_PACKET_TYPE_ALL_MULTICAST)) { - pf_ctrl |= 2; /* Multicast filter */ + pf_ctrl |= ET_RX_PFCTRL_MLTCST_FILTER_ENABLE; et1310_setup_device_for_multicast(adapter); } /* Runt packet filtering. Didn't work in version A silicon. */ - pf_ctrl |= (NIC_MIN_PACKET_SIZE + 4) << 16; - pf_ctrl |= 8; /* Fragment filter */ + pf_ctrl |= (NIC_MIN_PACKET_SIZE + 4) << ET_RX_PFCTRL_MIN_PKT_SZ_SHIFT; + pf_ctrl |= ET_RX_PFCTRL_FRAG_FILTER_ENABLE; if (adapter->registry_jumbo_packet > 8192) /* In order to transmit jumbo packets greater than 8k, the @@ -1290,7 +1301,7 @@ static void et1310_config_rxmac_regs(struct et131x_adapter *adapter) * but we still leave the packet filter on. */ writel(pf_ctrl, &rxmac->pf_ctrl); - writel(0x9, &rxmac->ctrl); + writel(ET_RX_CTRL_RXMAC_ENABLE | ET_RX_CTRL_WOL_DISABLE, &rxmac->ctrl); } static void et1310_config_txmac_regs(struct et131x_adapter *adapter) @@ -1401,7 +1412,7 @@ static int et131x_phy_mii_read(struct et131x_adapter *adapter, u8 addr, writel(0, &mac->mii_mgmt_cmd); /* Set up the register we need to read from on the correct PHY */ - writel(MII_ADDR(addr, reg), &mac->mii_mgmt_addr); + writel(ET_MAC_MII_ADDR(addr, reg), &mac->mii_mgmt_addr); writel(0x1, &mac->mii_mgmt_cmd); @@ -1409,7 +1420,7 @@ static int et131x_phy_mii_read(struct et131x_adapter *adapter, u8 addr, udelay(50); delay++; mii_indicator = readl(&mac->mii_mgmt_indicator); - } while ((mii_indicator & MGMT_WAIT) && delay < 50); + } while ((mii_indicator & ET_MAC_MGMT_WAIT) && delay < 50); /* If we hit the max delay, we could not read the register */ if (delay == 50) { @@ -1423,7 +1434,7 @@ static int et131x_phy_mii_read(struct et131x_adapter *adapter, u8 addr, /* If we hit here we were able to read the register and we need to * return the value to the caller */ - *value = readl(&mac->mii_mgmt_stat) & 0xFFFF; + *value = readl(&mac->mii_mgmt_stat) & ET_MAC_MIIMGMT_STAT_PHYCRTL_MASK; /* Stop the read operation */ writel(0, &mac->mii_mgmt_cmd); @@ -1483,7 +1494,7 @@ static int et131x_mii_write(struct et131x_adapter *adapter, u8 reg, u16 value) writel(0, &mac->mii_mgmt_cmd); /* Set up the register we need to write to on the correct PHY */ - writel(MII_ADDR(addr, reg), &mac->mii_mgmt_addr); + writel(ET_MAC_MII_ADDR(addr, reg), &mac->mii_mgmt_addr); /* Add the value to write to the registers to the mac */ writel(value, &mac->mii_mgmt_ctrl); @@ -1492,7 +1503,7 @@ static int et131x_mii_write(struct et131x_adapter *adapter, u8 reg, u16 value) udelay(50); delay++; mii_indicator = readl(&mac->mii_mgmt_indicator); - } while ((mii_indicator & MGMT_BUSY) && delay < 100); + } while ((mii_indicator & ET_MAC_MGMT_BUSY) && delay < 100); /* If we hit the max delay, we could not write the register */ if (delay == 100) { @@ -1528,7 +1539,7 @@ static void et1310_phy_access_mii_bit(struct et131x_adapter *adapter, u8 *value) { u16 reg; - u16 mask = 0x0001 << bitnum; + u16 mask = 1 << bitnum; /* Read the requested register */ et131x_mii_read(adapter, regnum, ®); @@ -1839,7 +1850,7 @@ static void et131x_config_rx_dma_regs(struct et131x_adapter *adapter) writel(rx_local->psr_num_entries - 1, &rx_dma->psr_num_des); writel(0, &rx_dma->psr_full_offset); - psr_num_des = readl(&rx_dma->psr_num_des) & 0xFFF; + psr_num_des = readl(&rx_dma->psr_num_des) & ET_RXDMA_PSR_NUM_DES_MASK; writel((psr_num_des * LO_MARK_PERCENT_FOR_PSR) / 100, &rx_dma->psr_min_des); @@ -1983,13 +1994,21 @@ static void et131x_adapter_setup(struct et131x_adapter *adapter) */ static void et131x_soft_reset(struct et131x_adapter *adapter) { - /* Disable MAC Core */ - writel(0xc00f0000, &adapter->regs->mac.cfg1); + u32 reg; - /* Set everything to a reset value */ - writel(0x7F, &adapter->regs->global.sw_reset); - writel(0x000f0000, &adapter->regs->mac.cfg1); - writel(0x00000000, &adapter->regs->mac.cfg1); + /* Disable MAC Core */ + reg = ET_MAC_CFG1_SOFT_RESET | ET_MAC_CFG1_SIM_RESET | + ET_MAC_CFG1_RESET_RXMC | ET_MAC_CFG1_RESET_TXMC | + ET_MAC_CFG1_RESET_RXFUNC | ET_MAC_CFG1_RESET_TXFUNC; + writel(reg, &adapter->regs->mac.cfg1); + + reg = ET_RESET_ALL; + writel(reg, &adapter->regs->global.sw_reset); + + reg = ET_MAC_CFG1_RESET_RXMC | ET_MAC_CFG1_RESET_TXMC | + ET_MAC_CFG1_RESET_RXFUNC | ET_MAC_CFG1_RESET_TXFUNC; + writel(reg, &adapter->regs->mac.cfg1); + writel(0, &adapter->regs->mac.cfg1); } /** @@ -3022,23 +3041,22 @@ static int nic_send_packet(struct et131x_adapter *adapter, struct tcb *tcb) if (phydev && phydev->speed == SPEED_1000) { if (++adapter->tx_ring.since_irq == PARM_TX_NUM_BUFS_DEF) { /* Last element & Interrupt flag */ - desc[frag - 1].flags = 0x5; + desc[frag - 1].flags = TXDESC_FLAG_INTPROC | TXDESC_FLAG_LASTPKT; adapter->tx_ring.since_irq = 0; } else { /* Last element */ - desc[frag - 1].flags = 0x1; + desc[frag - 1].flags = TXDESC_FLAG_LASTPKT; } } else - desc[frag - 1].flags = 0x5; + desc[frag - 1].flags = TXDESC_FLAG_INTPROC | TXDESC_FLAG_LASTPKT; - desc[0].flags |= 2; /* First element flag */ + desc[0].flags |= TXDESC_FLAG_FIRSTPKT; tcb->index_start = adapter->tx_ring.send_idx; tcb->stale = 0; spin_lock_irqsave(&adapter->send_hw_lock, flags); - thiscopy = NUM_DESC_PER_RING_TX - - INDEX10(adapter->tx_ring.send_idx); + thiscopy = NUM_DESC_PER_RING_TX - INDEX10(adapter->tx_ring.send_idx); if (thiscopy >= frag) { remainder = 0; diff --git a/drivers/staging/et131x/et131x.h b/drivers/staging/et131x/et131x.h index 9fa47f91a9f..bbe78a703a2 100644 --- a/drivers/staging/et131x/et131x.h +++ b/drivers/staging/et131x/et131x.h @@ -145,6 +145,8 @@ *31: selfclr_disable */ +#define ET_RESET_ALL 0x007F; + /* * SLV Timer reg at address 0x002C (low 24 bits) */ @@ -392,6 +394,8 @@ struct txdma_regs { /* Location: */ * 11-0: psr ndes */ +#define ET_RXDMA_PSR_NUM_DES_MASK 0xFFF; + /* * structure for packet status ring available offset reg in rxdma address map * located at address 0x202C @@ -567,6 +571,9 @@ struct rxdma_regs { /* Location: */ * 0: txmac_en */ +#define ET_TX_CTRL_FC_DISABLE 0x0008 +#define ET_TX_CTRL_TXMAC_ENABLE 0x0001 + /* * structure for shadow pointer reg in txmac address map * located at address 0x3004 @@ -682,6 +689,9 @@ struct txmac_regs { /* Location: */ * 0: rxmac_en */ +#define ET_RX_CTRL_WOL_DISABLE 0x0008 +#define ET_RX_CTRL_RXMAC_ENABLE 0x0001 + /* * structure for Wake On Lan Control and CRC 0 reg in rxmac address map * located at address 0x4004 @@ -723,9 +733,9 @@ struct txmac_regs { /* Location: */ * 7-0: sa6 */ -#define ET_WOL_LO_SA3_SHIFT 24 -#define ET_WOL_LO_SA4_SHIFT 16 -#define ET_WOL_LO_SA5_SHIFT 8 +#define ET_RX_WOL_LO_SA3_SHIFT 24 +#define ET_RX_WOL_LO_SA4_SHIFT 16 +#define ET_RX_WOL_LO_SA5_SHIFT 8 /* * structure for Wake On Lan Source Address Hi reg in rxmac address map @@ -736,7 +746,7 @@ struct txmac_regs { /* Location: */ * 7-0: sa2 */ -#define ET_WOL_HI_SA1_SHIFT 8 +#define ET_RX_WOL_HI_SA1_SHIFT 8 /* * structure for Wake On Lan mask reg in rxmac address map @@ -754,9 +764,9 @@ struct txmac_regs { /* Location: */ * 7-0: addr1_6 */ -#define ET_UNI_PF_ADDR1_3_SHIFT 24 -#define ET_UNI_PF_ADDR1_4_SHIFT 16 -#define ET_UNI_PF_ADDR1_5_SHIFT 8 +#define ET_RX_UNI_PF_ADDR1_3_SHIFT 24 +#define ET_RX_UNI_PF_ADDR1_4_SHIFT 16 +#define ET_RX_UNI_PF_ADDR1_5_SHIFT 8 /* * structure for Unicast Paket Filter Address 2 reg in rxmac address map @@ -768,9 +778,9 @@ struct txmac_regs { /* Location: */ * 7-0: addr2_6 */ -#define ET_UNI_PF_ADDR2_3_SHIFT 24 -#define ET_UNI_PF_ADDR2_4_SHIFT 16 -#define ET_UNI_PF_ADDR2_5_SHIFT 8 +#define ET_RX_UNI_PF_ADDR2_3_SHIFT 24 +#define ET_RX_UNI_PF_ADDR2_4_SHIFT 16 +#define ET_RX_UNI_PF_ADDR2_5_SHIFT 8 /* * structure for Unicast Paket Filter Address 1 & 2 reg in rxmac address map @@ -782,10 +792,9 @@ struct txmac_regs { /* Location: */ * 7-0: addr1_2 */ -#define ET_UNI_PF_ADDR2_1_SHIFT 24 -#define ET_UNI_PF_ADDR2_2_SHIFT 16 -#define ET_UNI_PF_ADDR1_1_SHIFT 8 - +#define ET_RX_UNI_PF_ADDR2_1_SHIFT 24 +#define ET_RX_UNI_PF_ADDR2_2_SHIFT 16 +#define ET_RX_UNI_PF_ADDR1_1_SHIFT 8 /* * structure for Multicast Hash reg in rxmac address map @@ -806,6 +815,12 @@ struct txmac_regs { /* Location: */ * 0: filter_broad_en */ +#define ET_RX_PFCTRL_MIN_PKT_SZ_SHIFT 16; +#define ET_RX_PFCTRL_FRAG_FILTER_ENABLE 0x0008; +#define ET_RX_PFCTRL_UNICST_FILTER_ENABLE 0x0004; +#define ET_RX_PFCTRL_MLTCST_FILTER_ENABLE 0x0002; +#define ET_RX_PFCTRL_BRDCST_FILTER_ENABLE 0x0001; + /* * structure for Memory Controller Interface Control Max Segment reg in rxmac * address map. Located at address 0x4088 @@ -816,6 +831,10 @@ struct txmac_regs { /* Location: */ * 0: seg_en */ +#define ET_RX_MCIF_CTRL_MAX_SEG_SIZE_SHIFT 2; +#define ET_RX_MCIF_CTRL_MAX_SEG_FC_ENABLE 0x0002; +#define ET_RX_MCIF_CTRL_MAX_SEG_ENABLE 0x0001; + /* * structure for Memory Controller Interface Water Mark reg in rxmac address * map. Located at address 0x408C @@ -915,7 +934,6 @@ struct rxmac_regs { /* Location: */ /* END OF RXMAC REGISTER ADDRESS MAP */ - /* START OF MAC REGISTER ADDRESS MAP */ /* @@ -940,12 +958,18 @@ struct rxmac_regs { /* Location: */ * 0: tx enable */ -#define CFG1_LOOPBACK 0x00000100 -#define CFG1_RX_FLOW 0x00000020 -#define CFG1_TX_FLOW 0x00000010 -#define CFG1_RX_ENABLE 0x00000004 -#define CFG1_TX_ENABLE 0x00000001 -#define CFG1_WAIT 0x0000000A /* RX & TX syncd */ +#define ET_MAC_CFG1_SOFT_RESET 0x80000000 +#define ET_MAC_CFG1_SIM_RESET 0x40000000 +#define ET_MAC_CFG1_RESET_RXMC 0x00080000 +#define ET_MAC_CFG1_RESET_TXMC 0x00040000 +#define ET_MAC_CFG1_RESET_RXFUNC 0x00020000 +#define ET_MAC_CFG1_RESET_TXFUNC 0x00010000 +#define ET_MAC_CFG1_LOOPBACK 0x00000100 +#define ET_MAC_CFG1_RX_FLOW 0x00000020 +#define ET_MAC_CFG1_TX_FLOW 0x00000010 +#define ET_MAC_CFG1_RX_ENABLE 0x00000004 +#define ET_MAC_CFG1_TX_ENABLE 0x00000001 +#define ET_MAC_CFG1_WAIT 0x0000000A /* RX & TX syncd */ /* * structure for configuration #2 reg in mac address map. @@ -963,6 +987,15 @@ struct rxmac_regs { /* Location: */ * 0: full duplex */ +#define ET_MAC_CFG2_PREAMBLE_SHIFT 12; +#define ET_MAC_CFG2_IFMODE_MASK 0x0300; +#define ET_MAC_CFG2_IFMODE_1000 0x0200; +#define ET_MAC_CFG2_IFMODE_100 0x0100; +#define ET_MAC_CFG2_IFMODE_HUGE_FRAME 0x0020; +#define ET_MAC_CFG2_IFMODE_LEN_CHECK 0x0010; +#define ET_MAC_CFG2_IFMODE_PAD_CRC 0x0004; +#define ET_MAC_CFG2_IFMODE_CRC_ENABLE 0x0002; +#define ET_MAC_CFG2_IFMODE_FULL_DPLX 0x0001; /* * structure for Interpacket gap reg in mac address map. @@ -1017,6 +1050,8 @@ struct rxmac_regs { /* Location: */ * 2-0: mgmt clock reset */ +#define ET_MAC_MIIMGMT_CLK_RST 0x0007 + /* * structure for MII Management Command reg in mac address map. * located at address 0x5024 @@ -1033,7 +1068,7 @@ struct rxmac_regs { /* Location: */ * 4-0: register */ -#define MII_ADDR(phy, reg) ((phy) << 8 | (reg)) +#define ET_MAC_MII_ADDR(phy, reg) ((phy) << 8 | (reg)) /* * structure for MII Management Control reg in mac address map. @@ -1049,6 +1084,8 @@ struct rxmac_regs { /* Location: */ * 15-0: phy control */ +#define ET_MAC_MIIMGMT_STAT_PHYCRTL_MASK 0xFFFF; + /* * structure for MII Management Indicators reg in mac address map. * located at address 0x5034 @@ -1058,8 +1095,8 @@ struct rxmac_regs { /* Location: */ * 0: busy */ -#define MGMT_BUSY 0x00000001 /* busy */ -#define MGMT_WAIT 0x00000005 /* busy | not valid */ +#define ET_MAC_MGMT_BUSY 0x00000001 /* busy */ +#define ET_MAC_MGMT_WAIT 0x00000005 /* busy | not valid */ /* * structure for Interface Control reg in mac address map. @@ -1084,6 +1121,9 @@ struct rxmac_regs { /* Location: */ * 0: enable jabber protection */ +#define ET_MAC_IFCTRL_GHDMODE (1 << 26) +#define ET_MAC_IFCTRL_PHYMODE (1 << 24) + /* * structure for Interface Status reg in mac address map. * located at address 0x503C -- 2.20.1