From 96cc017c5b7ec095ef047d3c1952b6b6bbf98943 Mon Sep 17 00:00:00 2001 From: Shengzhou Liu Date: Fri, 26 Aug 2011 11:18:21 +0800 Subject: [PATCH] powerpc/p3060qds: Add support for P3060QDS board The P3060QDS is a Freescale reference board that hosts the six-core P3060 SOC. The P3060 Processor combines six e500mc Power Architecture processor cores with high-performance datapath acceleration architecture(DPAA), CoreNet fabric infrastructure, as well as network and peripheral interfaces. P3060QDS Board Overview: Memory subsystem: - 2G Bytes unbuffered DDR3 SDRAM SO-DIMM(64bit bus) - 128M Bytes NOR flash single-chip memory - 16M Bytes SPI flash - 8K Bytes AT24C64 I2C EEPROM Ethernet: - 4x1G + 4x1G/2.5G Ethernet controllers - 2xRGMII + 1xMII, three VSC8641 PHYs on board - Suport multiple Vitesse VSC8234 SGMII Cards in Slot1/2/3 PCIe: Two PCI Express 2.0 controllers/ports USB: Two USB2.0, USB1(TYPE-A) and USB2(TYPE-AB) on board I2C: Four I2C controllers UART: Supports up to four UARTs RapidIO: Supports two serial RapidIO ports Signed-off-by: Shengzhou Liu Signed-off-by: Kumar Gala --- arch/powerpc/boot/dts/p3060qds.dts | 238 ++++++ arch/powerpc/boot/dts/p3060si.dtsi | 719 +++++++++++++++++++ arch/powerpc/configs/corenet32_smp_defconfig | 1 + arch/powerpc/platforms/85xx/Kconfig | 12 + arch/powerpc/platforms/85xx/Makefile | 1 + arch/powerpc/platforms/85xx/p3060_qds.c | 77 ++ 6 files changed, 1048 insertions(+) create mode 100644 arch/powerpc/boot/dts/p3060qds.dts create mode 100644 arch/powerpc/boot/dts/p3060si.dtsi create mode 100644 arch/powerpc/platforms/85xx/p3060_qds.c diff --git a/arch/powerpc/boot/dts/p3060qds.dts b/arch/powerpc/boot/dts/p3060qds.dts new file mode 100644 index 000000000000..08b9193213e7 --- /dev/null +++ b/arch/powerpc/boot/dts/p3060qds.dts @@ -0,0 +1,238 @@ +/* + * P3060QDS Device Tree Source + * + * Copyright 2011 Freescale Semiconductor Inc. + * + * Redistribution and use in source and binary forms, with or without + * modification, are permitted provided that the following conditions are met: + * * Redistributions of source code must retain the above copyright + * notice, this list of conditions and the following disclaimer. + * * Redistributions in binary form must reproduce the above copyright + * notice, this list of conditions and the following disclaimer in the + * documentation and/or other materials provided with the distribution. + * * Neither the name of Freescale Semiconductor nor the + * names of its contributors may be used to endorse or promote products + * derived from this software without specific prior written permission. + * + * + * ALTERNATIVELY, this software may be distributed under the terms of the + * GNU General Public License ("GPL") as published by the Free Software + * Foundation, either version 2 of that License or (at your option) any + * later version. + * + * THIS SOFTWARE IS PROVIDED BY Freescale Semiconductor ``AS IS'' AND ANY + * EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED + * WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE + * DISCLAIMED. IN NO EVENT SHALL Freescale Semiconductor BE LIABLE FOR ANY + * DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES + * (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; + * LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND + * ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT + * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS + * SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. + */ + +/include/ "p3060si.dtsi" + +/ { + model = "fsl,P3060QDS"; + compatible = "fsl,P3060QDS"; + #address-cells = <2>; + #size-cells = <2>; + interrupt-parent = <&mpic>; + + memory { + device_type = "memory"; + }; + + dcsr: dcsr@f00000000 { + ranges = <0x00000000 0xf 0x00000000 0x01008000>; + }; + + soc: soc@ffe000000 { + spi@110000 { + flash@0 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "spansion,s25sl12801"; + reg = <0>; + spi-max-frequency = <40000000>; /* input clock */ + partition@u-boot { + label = "u-boot"; + reg = <0x00000000 0x00100000>; + read-only; + }; + partition@kernel { + label = "kernel"; + reg = <0x00100000 0x00500000>; + read-only; + }; + partition@dtb { + label = "dtb"; + reg = <0x00600000 0x00100000>; + read-only; + }; + partition@fs { + label = "file system"; + reg = <0x00700000 0x00900000>; + }; + }; + flash@1 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "spansion,en25q32b"; + reg = <1>; + spi-max-frequency = <40000000>; /* input clock */ + partition@spi1 { + label = "spi1"; + reg = <0x00000000 0x00400000>; + }; + }; + flash@2 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "atmel,at45db081d"; + reg = <2>; + spi-max-frequency = <40000000>; /* input clock */ + partition@spi1 { + label = "spi2"; + reg = <0x00000000 0x00100000>; + }; + }; + flash@3 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "spansion,sst25wf040"; + reg = <3>; + spi-max-frequency = <40000000>; /* input clock */ + partition@spi3 { + label = "spi3"; + reg = <0x00000000 0x00080000>; + }; + }; + }; + + i2c@118000 { + eeprom@51 { + compatible = "at24,24c256"; + reg = <0x51>; + }; + eeprom@53 { + compatible = "at24,24c256"; + reg = <0x53>; + }; + rtc@68 { + compatible = "dallas,ds3232"; + reg = <0x68>; + interrupts = <0x1 0x1 0 0>; + }; + }; + + usb0: usb@210000 { + phy_type = "ulpi"; + }; + + usb1: usb@211000 { + dr_mode = "host"; + phy_type = "ulpi"; + }; + }; + + rapidio@ffe0c0000 { + reg = <0xf 0xfe0c0000 0 0x11000>; + + port1 { + ranges = <0 0 0xc 0x20000000 0 0x10000000>; + }; + port2 { + ranges = <0 0 0xc 0x30000000 0 0x10000000>; + }; + }; + + localbus@ffe124000 { + reg = <0xf 0xfe124000 0 0x1000>; + ranges = <0 0 0xf 0xe8000000 0x08000000 + 2 0 0xf 0xffa00000 0x00040000 + 3 0 0xf 0xffdf0000 0x00008000>; + + flash@0,0 { + compatible = "cfi-flash"; + reg = <0 0 0x08000000>; + bank-width = <2>; + device-width = <2>; + }; + + nand@2,0 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "fsl,elbc-fcm-nand"; + reg = <0x2 0x0 0x40000>; + + partition@0 { + label = "NAND U-Boot Image"; + reg = <0x0 0x02000000>; + read-only; + }; + + partition@2000000 { + label = "NAND Root File System"; + reg = <0x02000000 0x10000000>; + }; + + partition@12000000 { + label = "NAND Compressed RFS Image"; + reg = <0x12000000 0x08000000>; + }; + + partition@1a000000 { + label = "NAND Linux Kernel Image"; + reg = <0x1a000000 0x04000000>; + }; + + partition@1e000000 { + label = "NAND DTB Image"; + reg = <0x1e000000 0x01000000>; + }; + + partition@1f000000 { + label = "NAND Writable User area"; + reg = <0x1f000000 0x21000000>; + }; + }; + + board-control@3,0 { + compatible = "fsl,p3060qds-fpga", "fsl,fpga-qixis"; + reg = <3 0 0x100>; + }; + }; + + pci0: pcie@ffe200000 { + reg = <0xf 0xfe200000 0 0x1000>; + ranges = <0x02000000 0 0xe0000000 0xc 0x00000000 0x0 0x20000000 + 0x01000000 0 0x00000000 0xf 0xf8000000 0x0 0x00010000>; + pcie@0 { + ranges = <0x02000000 0 0xe0000000 + 0x02000000 0 0xe0000000 + 0 0x20000000 + + 0x01000000 0 0x00000000 + 0x01000000 0 0x00000000 + 0 0x00010000>; + }; + }; + + pci1: pcie@ffe201000 { + reg = <0xf 0xfe201000 0 0x1000>; + ranges = <0x02000000 0x0 0xe0000000 0xc 0x20000000 0x0 0x20000000 + 0x01000000 0x0 0x00000000 0xf 0xf8010000 0x0 0x00010000>; + pcie@0 { + ranges = <0x02000000 0 0xe0000000 + 0x02000000 0 0xe0000000 + 0 0x20000000 + + 0x01000000 0 0x00000000 + 0x01000000 0 0x00000000 + 0 0x00010000>; + }; + }; +}; diff --git a/arch/powerpc/boot/dts/p3060si.dtsi b/arch/powerpc/boot/dts/p3060si.dtsi new file mode 100644 index 000000000000..68947e157bbc --- /dev/null +++ b/arch/powerpc/boot/dts/p3060si.dtsi @@ -0,0 +1,719 @@ +/* + * P3060 Silicon Device Tree Source + * + * Copyright 2011 Freescale Semiconductor Inc. + * + * Redistribution and use in source and binary forms, with or without + * modification, are permitted provided that the following conditions are met: + * * Redistributions of source code must retain the above copyright + * notice, this list of conditions and the following disclaimer. + * * Redistributions in binary form must reproduce the above copyright + * notice, this list of conditions and the following disclaimer in the + * documentation and/or other materials provided with the distribution. + * * Neither the name of Freescale Semiconductor nor the + * names of its contributors may be used to endorse or promote products + * derived from this software without specific prior written permission. + * + * + * ALTERNATIVELY, this software may be distributed under the terms of the + * GNU General Public License ("GPL") as published by the Free Software + * Foundation, either version 2 of that License or (at your option) any + * later version. + * + * THIS SOFTWARE IS PROVIDED BY Freescale Semiconductor ``AS IS'' AND ANY + * EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED + * WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE + * DISCLAIMED. IN NO EVENT SHALL Freescale Semiconductor BE LIABLE FOR ANY + * DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES + * (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; + * LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND + * ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT + * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS + * SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. + */ + +/dts-v1/; + +/ { + compatible = "fsl,P3060"; + #address-cells = <2>; + #size-cells = <2>; + interrupt-parent = <&mpic>; + + aliases { + ccsr = &soc; + dcsr = &dcsr; + + serial0 = &serial0; + serial1 = &serial1; + serial2 = &serial2; + serial3 = &serial3; + pci0 = &pci0; + pci1 = &pci1; + usb0 = &usb0; + usb1 = &usb1; + dma0 = &dma0; + dma1 = &dma1; + msi0 = &msi0; + msi1 = &msi1; + msi2 = &msi2; + + crypto = &crypto; + sec_jr0 = &sec_jr0; + sec_jr1 = &sec_jr1; + sec_jr2 = &sec_jr2; + sec_jr3 = &sec_jr3; + rtic_a = &rtic_a; + rtic_b = &rtic_b; + rtic_c = &rtic_c; + rtic_d = &rtic_d; + sec_mon = &sec_mon; + }; + + cpus { + #address-cells = <1>; + #size-cells = <0>; + + cpu0: PowerPC,e500mc@0 { + device_type = "cpu"; + reg = <0>; + next-level-cache = <&L2_0>; + L2_0: l2-cache { + next-level-cache = <&cpc>; + }; + }; + cpu1: PowerPC,e500mc@1 { + device_type = "cpu"; + reg = <1>; + next-level-cache = <&L2_1>; + L2_1: l2-cache { + next-level-cache = <&cpc>; + }; + }; + cpu4: PowerPC,e500mc@4 { + device_type = "cpu"; + reg = <4>; + next-level-cache = <&L2_4>; + L2_4: l2-cache { + next-level-cache = <&cpc>; + }; + }; + cpu5: PowerPC,e500mc@5 { + device_type = "cpu"; + reg = <5>; + next-level-cache = <&L2_5>; + L2_5: l2-cache { + next-level-cache = <&cpc>; + }; + }; + cpu6: PowerPC,e500mc@6 { + device_type = "cpu"; + reg = <6>; + next-level-cache = <&L2_6>; + L2_6: l2-cache { + next-level-cache = <&cpc>; + }; + }; + cpu7: PowerPC,e500mc@7 { + device_type = "cpu"; + reg = <7>; + next-level-cache = <&L2_7>; + L2_7: l2-cache { + next-level-cache = <&cpc>; + }; + }; + }; + + dcsr: dcsr@f00000000 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "fsl,dcsr", "simple-bus"; + + dcsr-epu@0 { + compatible = "fsl,dcsr-epu"; + interrupts = <52 2 0 0 + 84 2 0 0 + 85 2 0 0>; + interrupt-parent = <&mpic>; + reg = <0x0 0x1000>; + }; + dcsr-npc { + compatible = "fsl,dcsr-npc"; + reg = <0x1000 0x1000 0x1000000 0x8000>; + }; + dcsr-nxc@2000 { + compatible = "fsl,dcsr-nxc"; + reg = <0x2000 0x1000>; + }; + dcsr-corenet { + compatible = "fsl,dcsr-corenet"; + reg = <0x8000 0x1000 0xB0000 0x1000>; + }; + dcsr-dpaa@9000 { + compatible = "fsl,p3060-dcsr-dpaa", "fsl,dcsr-dpaa"; + reg = <0x9000 0x1000>; + }; + dcsr-ocn@11000 { + compatible = "fsl,p3060-dcsr-ocn", "fsl,dcsr-ocn"; + reg = <0x11000 0x1000>; + }; + dcsr-ddr@12000 { + compatible = "fsl,dcsr-ddr"; + dev-handle = <&ddr>; + reg = <0x12000 0x1000>; + }; + dcsr-nal@18000 { + compatible = "fsl,p3060-dcsr-nal", "fsl,dcsr-nal"; + reg = <0x18000 0x1000>; + }; + dcsr-rcpm@22000 { + compatible = "fsl,p3060-dcsr-rcpm", "fsl,dcsr-rcpm"; + reg = <0x22000 0x1000>; + }; + dcsr-cpu-sb-proxy@40000 { + compatible = "fsl,dcsr-e500mc-sb-proxy", "fsl,dcsr-cpu-sb-proxy"; + cpu-handle = <&cpu0>; + reg = <0x40000 0x1000>; + }; + dcsr-cpu-sb-proxy@41000 { + compatible = "fsl,dcsr-e500mc-sb-proxy", "fsl,dcsr-cpu-sb-proxy"; + cpu-handle = <&cpu1>; + reg = <0x41000 0x1000>; + }; + dcsr-cpu-sb-proxy@44000 { + compatible = "fsl,dcsr-e500mc-sb-proxy", "fsl,dcsr-cpu-sb-proxy"; + cpu-handle = <&cpu4>; + reg = <0x44000 0x1000>; + }; + dcsr-cpu-sb-proxy@45000 { + compatible = "fsl,dcsr-e500mc-sb-proxy", "fsl,dcsr-cpu-sb-proxy"; + cpu-handle = <&cpu5>; + reg = <0x45000 0x1000>; + }; + dcsr-cpu-sb-proxy@46000 { + compatible = "fsl,dcsr-e500mc-sb-proxy", "fsl,dcsr-cpu-sb-proxy"; + cpu-handle = <&cpu6>; + reg = <0x46000 0x1000>; + }; + dcsr-cpu-sb-proxy@47000 { + compatible = "fsl,dcsr-e500mc-sb-proxy", "fsl,dcsr-cpu-sb-proxy"; + cpu-handle = <&cpu7>; + reg = <0x47000 0x1000>; + }; + }; + + soc: soc@ffe000000 { + #address-cells = <1>; + #size-cells = <1>; + device_type = "soc"; + compatible = "simple-bus"; + ranges = <0x00000000 0xf 0xfe000000 0x1000000>; + reg = <0xf 0xfe000000 0 0x00001000>; + + soc-sram-error { + compatible = "fsl,soc-sram-error"; + interrupts = <16 2 1 29>; + }; + + corenet-law@0 { + compatible = "fsl,corenet-law"; + reg = <0x0 0x1000>; + fsl,num-laws = <32>; + }; + + ddr: memory-controller@8000 { + compatible = "fsl,qoriq-memory-controller-v4.4", "fsl,qoriq-memory-controller"; + reg = <0x8000 0x1000>; + interrupts = <16 2 1 23>; + }; + + cpc: l3-cache-controller@10000 { + compatible = "fsl,p3060-l3-cache-controller", "cache"; + reg = <0x10000 0x1000 + 0x11000 0x1000>; + interrupts = <16 2 1 27>; + }; + + corenet-cf@18000 { + compatible = "fsl,corenet-cf"; + reg = <0x18000 0x1000>; + interrupts = <16 2 1 31>; + fsl,ccf-num-csdids = <32>; + fsl,ccf-num-snoopids = <32>; + }; + + iommu@20000 { + compatible = "fsl,pamu-v1.0", "fsl,pamu"; + reg = <0x20000 0x5000>; + interrupts = < + 24 2 0 0 + 16 2 1 30>; + }; + + mpic: pic@40000 { + clock-frequency = <0>; + interrupt-controller; + #address-cells = <0>; + #interrupt-cells = <4>; + reg = <0x40000 0x40000>; + compatible = "fsl,mpic", "chrp,open-pic"; + device_type = "open-pic"; + }; + + msi0: msi@41600 { + compatible = "fsl,mpic-msi"; + reg = <0x41600 0x200>; + msi-available-ranges = <0 0x100>; + interrupts = < + 0xe0 0 0 0 + 0xe1 0 0 0 + 0xe2 0 0 0 + 0xe3 0 0 0 + 0xe4 0 0 0 + 0xe5 0 0 0 + 0xe6 0 0 0 + 0xe7 0 0 0>; + }; + + msi1: msi@41800 { + compatible = "fsl,mpic-msi"; + reg = <0x41800 0x200>; + msi-available-ranges = <0 0x100>; + interrupts = < + 0xe8 0 0 0 + 0xe9 0 0 0 + 0xea 0 0 0 + 0xeb 0 0 0 + 0xec 0 0 0 + 0xed 0 0 0 + 0xee 0 0 0 + 0xef 0 0 0>; + }; + + msi2: msi@41a00 { + compatible = "fsl,mpic-msi"; + reg = <0x41a00 0x200>; + msi-available-ranges = <0 0x100>; + interrupts = < + 0xf0 0 0 0 + 0xf1 0 0 0 + 0xf2 0 0 0 + 0xf3 0 0 0 + 0xf4 0 0 0 + 0xf5 0 0 0 + 0xf6 0 0 0 + 0xf7 0 0 0>; + }; + + rmu: rmu@d3000 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "fsl,srio-rmu"; + reg = <0xd3000 0x500>; + ranges = <0x0 0xd3000 0x500>; + + message-unit@0 { + compatible = "fsl,srio-msg-unit"; + reg = <0x0 0x100>; + interrupts = < + 60 2 0 0 /* msg1_tx_irq */ + 61 2 0 0>;/* msg1_rx_irq */ + }; + message-unit@100 { + compatible = "fsl,srio-msg-unit"; + reg = <0x100 0x100>; + interrupts = < + 62 2 0 0 /* msg2_tx_irq */ + 63 2 0 0>;/* msg2_rx_irq */ + }; + doorbell-unit@400 { + compatible = "fsl,srio-dbell-unit"; + reg = <0x400 0x80>; + interrupts = < + 56 2 0 0 /* bell_outb_irq */ + 57 2 0 0>;/* bell_inb_irq */ + }; + port-write-unit@4e0 { + compatible = "fsl,srio-port-write-unit"; + reg = <0x4e0 0x20>; + interrupts = <16 2 1 11>; + }; + }; + + guts: global-utilities@e0000 { + compatible = "fsl,qoriq-device-config-1.0"; + reg = <0xe0000 0xe00>; + fsl,has-rstcr; + #sleep-cells = <1>; + fsl,liodn-bits = <12>; + }; + + pins: global-utilities@e0e00 { + compatible = "fsl,qoriq-pin-control-1.0"; + reg = <0xe0e00 0x200>; + #sleep-cells = <2>; + }; + + clockgen: global-utilities@e1000 { + compatible = "fsl,p3060-clockgen", "fsl,qoriq-clockgen-1.0"; + reg = <0xe1000 0x1000>; + clock-frequency = <0>; + }; + + rcpm: global-utilities@e2000 { + compatible = "fsl,qoriq-rcpm-1.0"; + reg = <0xe2000 0x1000>; + #sleep-cells = <1>; + }; + + sfp: sfp@e8000 { + compatible = "fsl,p3060-sfp", "fsl,qoriq-sfp-1.0"; + reg = <0xe8000 0x1000>; + }; + + serdes: serdes@ea000 { + compatible = "fsl,p3060-serdes"; + reg = <0xea000 0x1000>; + }; + + dma0: dma@100300 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "fsl,p3060-dma", "fsl,eloplus-dma"; + reg = <0x100300 0x4>; + ranges = <0x0 0x100100 0x200>; + cell-index = <0>; + dma-channel@0 { + compatible = "fsl,p3060-dma-channel", + "fsl,eloplus-dma-channel"; + reg = <0x0 0x80>; + cell-index = <0>; + interrupts = <28 2 0 0>; + }; + dma-channel@80 { + compatible = "fsl,p3060-dma-channel", + "fsl,eloplus-dma-channel"; + reg = <0x80 0x80>; + cell-index = <1>; + interrupts = <29 2 0 0>; + }; + dma-channel@100 { + compatible = "fsl,p3060-dma-channel", + "fsl,eloplus-dma-channel"; + reg = <0x100 0x80>; + cell-index = <2>; + interrupts = <30 2 0 0>; + }; + dma-channel@180 { + compatible = "fsl,p3060-dma-channel", + "fsl,eloplus-dma-channel"; + reg = <0x180 0x80>; + cell-index = <3>; + interrupts = <31 2 0 0>; + }; + }; + + dma1: dma@101300 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "fsl,p3060-dma", "fsl,eloplus-dma"; + reg = <0x101300 0x4>; + ranges = <0x0 0x101100 0x200>; + cell-index = <1>; + dma-channel@0 { + compatible = "fsl,p3060-dma-channel", + "fsl,eloplus-dma-channel"; + reg = <0x0 0x80>; + cell-index = <0>; + interrupts = <32 2 0 0>; + }; + dma-channel@80 { + compatible = "fsl,p3060-dma-channel", + "fsl,eloplus-dma-channel"; + reg = <0x80 0x80>; + cell-index = <1>; + interrupts = <33 2 0 0>; + }; + dma-channel@100 { + compatible = "fsl,p3060-dma-channel", + "fsl,eloplus-dma-channel"; + reg = <0x100 0x80>; + cell-index = <2>; + interrupts = <34 2 0 0>; + }; + dma-channel@180 { + compatible = "fsl,p3060-dma-channel", + "fsl,eloplus-dma-channel"; + reg = <0x180 0x80>; + cell-index = <3>; + interrupts = <35 2 0 0>; + }; + }; + + spi@110000 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "fsl,p3060-espi", "fsl,mpc8536-espi"; + reg = <0x110000 0x1000>; + interrupts = <53 0x2 0 0>; + fsl,espi-num-chipselects = <4>; + }; + + i2c@118000 { + #address-cells = <1>; + #size-cells = <0>; + cell-index = <0>; + compatible = "fsl-i2c"; + reg = <0x118000 0x100>; + interrupts = <38 2 0 0>; + dfsrr; + }; + + i2c@118100 { + #address-cells = <1>; + #size-cells = <0>; + cell-index = <1>; + compatible = "fsl-i2c"; + reg = <0x118100 0x100>; + interrupts = <38 2 0 0>; + dfsrr; + }; + + i2c@119000 { + #address-cells = <1>; + #size-cells = <0>; + cell-index = <2>; + compatible = "fsl-i2c"; + reg = <0x119000 0x100>; + interrupts = <39 2 0 0>; + dfsrr; + }; + + i2c@119100 { + #address-cells = <1>; + #size-cells = <0>; + cell-index = <3>; + compatible = "fsl-i2c"; + reg = <0x119100 0x100>; + interrupts = <39 2 0 0>; + dfsrr; + }; + + serial0: serial@11c500 { + cell-index = <0>; + device_type = "serial"; + compatible = "ns16550"; + reg = <0x11c500 0x100>; + clock-frequency = <0>; + interrupts = <36 2 0 0>; + }; + + serial1: serial@11c600 { + cell-index = <1>; + device_type = "serial"; + compatible = "ns16550"; + reg = <0x11c600 0x100>; + clock-frequency = <0>; + interrupts = <36 2 0 0>; + }; + + serial2: serial@11d500 { + cell-index = <2>; + device_type = "serial"; + compatible = "ns16550"; + reg = <0x11d500 0x100>; + clock-frequency = <0>; + interrupts = <37 2 0 0>; + }; + + serial3: serial@11d600 { + cell-index = <3>; + device_type = "serial"; + compatible = "ns16550"; + reg = <0x11d600 0x100>; + clock-frequency = <0>; + interrupts = <37 2 0 0>; + }; + + gpio0: gpio@130000 { + compatible = "fsl,p3060-gpio", "fsl,qoriq-gpio"; + reg = <0x130000 0x1000>; + interrupts = <55 2 0 0>; + #gpio-cells = <2>; + gpio-controller; + }; + + usb0: usb@210000 { + compatible = "fsl,p3060-usb2-mph", + "fsl,mpc85xx-usb2-mph", "fsl-usb2-mph"; + reg = <0x210000 0x1000>; + #address-cells = <1>; + #size-cells = <0>; + interrupts = <44 0x2 0 0>; + }; + + usb1: usb@211000 { + compatible = "fsl,p3060-usb2-dr", + "fsl,mpc85xx-usb2-dr", "fsl-usb2-dr"; + reg = <0x211000 0x1000>; + #address-cells = <1>; + #size-cells = <0>; + interrupts = <45 0x2 0 0>; + }; + + crypto: crypto@300000 { + compatible = "fsl,sec-v4.1", "fsl,sec-v4.0"; + #address-cells = <1>; + #size-cells = <1>; + reg = <0x300000 0x10000>; + ranges = <0 0x300000 0x10000>; + interrupt-parent = <&mpic>; + interrupts = <92 2 0 0>; + + sec_jr0: jr@1000 { + compatible = "fsl,sec-v4.1-job-ring", "fsl,sec-v4.0-job-ring"; + reg = <0x1000 0x1000>; + interrupt-parent = <&mpic>; + interrupts = <88 2 0 0>; + }; + + sec_jr1: jr@2000 { + compatible = "fsl,sec-v4.1-job-ring", "fsl,sec-v4.0-job-ring"; + reg = <0x2000 0x1000>; + interrupt-parent = <&mpic>; + interrupts = <89 2 0 0>; + }; + + sec_jr2: jr@3000 { + compatible = "fsl,sec-v4.1-job-ring", "fsl,sec-v4.0-job-ring"; + reg = <0x3000 0x1000>; + interrupt-parent = <&mpic>; + interrupts = <90 2 0 0>; + }; + + sec_jr3: jr@4000 { + compatible = "fsl,sec-v4.1-job-ring", "fsl,sec-v4.0-job-ring"; + reg = <0x4000 0x1000>; + interrupt-parent = <&mpic>; + interrupts = <91 2 0 0>; + }; + + rtic@6000 { + compatible = "fsl,sec-v4.1-rtic", "fsl,sec-v4.0-rtic"; + #address-cells = <1>; + #size-cells = <1>; + reg = <0x6000 0x100>; + ranges = <0x0 0x6100 0xe00>; + + rtic_a: rtic-a@0 { + compatible = "fsl,sec-v4.1-rtic-memory", "fsl,sec-v4.0-rtic-memory"; + reg = <0x00 0x20 0x100 0x80>; + }; + + rtic_b: rtic-b@20 { + compatible = "fsl,sec-v4.1-rtic-memory", "fsl,sec-v4.0-rtic-memory"; + reg = <0x20 0x20 0x200 0x80>; + }; + + rtic_c: rtic-c@40 { + compatible = "fsl,sec-v4.1-rtic-memory", "fsl,sec-v4.0-rtic-memory"; + reg = <0x40 0x20 0x300 0x80>; + }; + + rtic_d: rtic-d@60 { + compatible = "fsl,sec-v4.1-rtic-memory", "fsl,sec-v4.0-rtic-memory"; + reg = <0x60 0x20 0x500 0x80>; + }; + }; + }; + + sec_mon: sec_mon@314000 { + compatible = "fsl,sec-v4.1-mon", "fsl,sec-v4.0-mon"; + reg = <0x314000 0x1000>; + interrupt-parent = <&mpic>; + interrupts = <93 2 0 0>; + }; + }; + + rapidio@ffe0c0000 { + compatible = "fsl,srio"; + interrupts = <16 2 1 11>; + #address-cells = <2>; + #size-cells = <2>; + fsl,srio-rmu-handle = <&rmu>; + ranges; + + port1 { + #address-cells = <2>; + #size-cells = <2>; + cell-index = <1>; + }; + + port2 { + #address-cells = <2>; + #size-cells = <2>; + cell-index = <2>; + }; + }; + + localbus@ffe124000 { + compatible = "fsl,p3060-elbc", "fsl,elbc", "simple-bus"; + interrupts = <25 2 0 0>; + #address-cells = <2>; + #size-cells = <1>; + }; + + pci0: pcie@ffe200000 { + compatible = "fsl,p3060-pcie", "fsl,qoriq-pcie-v2.2"; + device_type = "pci"; + #size-cells = <2>; + #address-cells = <3>; + bus-range = <0x0 0xff>; + clock-frequency = <33333333>; + fsl,msi = <&msi0>; + interrupts = <16 2 1 15>; + pcie@0 { + reg = <0 0 0 0 0>; + #interrupt-cells = <1>; + #size-cells = <2>; + #address-cells = <3>; + device_type = "pci"; + interrupts = <16 2 1 15>; + interrupt-map-mask = <0xf800 0 0 7>; + interrupt-map = < + /* IDSEL 0x0 */ + 0000 0 0 1 &mpic 40 1 0 0 + 0000 0 0 2 &mpic 1 1 0 0 + 0000 0 0 3 &mpic 2 1 0 0 + 0000 0 0 4 &mpic 3 1 0 0 + >; + }; + }; + + pci1: pcie@ffe201000 { + compatible = "fsl,p3060-pcie", "fsl,qoriq-pcie-v2.2"; + device_type = "pci"; + #size-cells = <2>; + #address-cells = <3>; + bus-range = <0 0xff>; + clock-frequency = <33333333>; + fsl,msi = <&msi1>; + interrupts = <16 2 1 14>; + pcie@0 { + reg = <0 0 0 0 0>; + #interrupt-cells = <1>; + #size-cells = <2>; + #address-cells = <3>; + device_type = "pci"; + interrupts = <16 2 1 14>; + interrupt-map-mask = <0xf800 0 0 7>; + interrupt-map = < + /* IDSEL 0x0 */ + 0000 0 0 1 &mpic 41 1 0 0 + 0000 0 0 2 &mpic 5 1 0 0 + 0000 0 0 3 &mpic 6 1 0 0 + 0000 0 0 4 &mpic 7 1 0 0 + >; + }; + }; +}; diff --git a/arch/powerpc/configs/corenet32_smp_defconfig b/arch/powerpc/configs/corenet32_smp_defconfig index 797e1fd1a5b9..f087de6ec03f 100644 --- a/arch/powerpc/configs/corenet32_smp_defconfig +++ b/arch/powerpc/configs/corenet32_smp_defconfig @@ -23,6 +23,7 @@ CONFIG_MODVERSIONS=y # CONFIG_BLK_DEV_BSG is not set CONFIG_P2041_RDB=y CONFIG_P3041_DS=y +CONFIG_P3060_QDS=y CONFIG_P4080_DS=y CONFIG_P5020_DS=y CONFIG_HIGHMEM=y diff --git a/arch/powerpc/platforms/85xx/Kconfig b/arch/powerpc/platforms/85xx/Kconfig index 7f84cfd1726e..45023e26aea3 100644 --- a/arch/powerpc/platforms/85xx/Kconfig +++ b/arch/powerpc/platforms/85xx/Kconfig @@ -197,6 +197,18 @@ config P3041_DS help This option enables support for the P3041 DS board +config P3060_QDS + bool "Freescale P3060 QDS" + select DEFAULT_UIMAGE + select PPC_E500MC + select PHYS_64BIT + select SWIOTLB + select MPC8xxx_GPIO + select HAS_RAPIDIO + select PPC_EPAPR_HV_PIC + help + This option enables support for the P3060 QDS board + config P4080_DS bool "Freescale P4080 DS" select DEFAULT_UIMAGE diff --git a/arch/powerpc/platforms/85xx/Makefile b/arch/powerpc/platforms/85xx/Makefile index 39e6c22f06fa..bc5acb95917a 100644 --- a/arch/powerpc/platforms/85xx/Makefile +++ b/arch/powerpc/platforms/85xx/Makefile @@ -15,6 +15,7 @@ obj-$(CONFIG_P1022_DS) += p1022_ds.o obj-$(CONFIG_P1023_RDS) += p1023_rds.o obj-$(CONFIG_P2041_RDB) += p2041_rdb.o corenet_ds.o obj-$(CONFIG_P3041_DS) += p3041_ds.o corenet_ds.o +obj-$(CONFIG_P3060_QDS) += p3060_qds.o corenet_ds.o obj-$(CONFIG_P4080_DS) += p4080_ds.o corenet_ds.o obj-$(CONFIG_P5020_DS) += p5020_ds.o corenet_ds.o obj-$(CONFIG_STX_GP3) += stx_gp3.o diff --git a/arch/powerpc/platforms/85xx/p3060_qds.c b/arch/powerpc/platforms/85xx/p3060_qds.c new file mode 100644 index 000000000000..01dcf44871e9 --- /dev/null +++ b/arch/powerpc/platforms/85xx/p3060_qds.c @@ -0,0 +1,77 @@ +/* + * P3060 QDS Setup + * + * Copyright 2011 Freescale Semiconductor Inc. + * + * This program is free software; you can redistribute it and/or modify it + * under the terms of the GNU General Public License as published by the + * Free Software Foundation; either version 2 of the License, or (at your + * option) any later version. + */ + +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include "corenet_ds.h" + +/* + * Called very early, device-tree isn't unflattened + */ +static int __init p3060_qds_probe(void) +{ + unsigned long root = of_get_flat_dt_root(); +#ifdef CONFIG_SMP + extern struct smp_ops_t smp_85xx_ops; +#endif + + if (of_flat_dt_is_compatible(root, "fsl,P3060QDS")) + return 1; + + /* Check if we're running under the Freescale hypervisor */ + if (of_flat_dt_is_compatible(root, "fsl,P3060QDS-hv")) { + ppc_md.init_IRQ = ehv_pic_init; + ppc_md.get_irq = ehv_pic_get_irq; + ppc_md.restart = fsl_hv_restart; + ppc_md.power_off = fsl_hv_halt; + ppc_md.halt = fsl_hv_halt; +#ifdef CONFIG_SMP + /* + * Disable the timebase sync operations because we can't write + * to the timebase registers under the hypervisor. + */ + smp_85xx_ops.give_timebase = NULL; + smp_85xx_ops.take_timebase = NULL; +#endif + return 1; + } + + return 0; +} + +define_machine(p3060_qds) { + .name = "P3060 QDS", + .probe = p3060_qds_probe, + .setup_arch = corenet_ds_setup_arch, + .init_IRQ = corenet_ds_pic_init, +#ifdef CONFIG_PCI + .pcibios_fixup_bus = fsl_pcibios_fixup_bus, +#endif + .get_irq = mpic_get_coreint_irq, + .restart = fsl_rstcr_restart, + .calibrate_decr = generic_calibrate_decr, + .progress = udbg_progress, + .power_save = e500_idle, +}; + +machine_device_initcall(p3060_qds, declare_of_platform_devices); + +#ifdef CONFIG_SWIOTLB +machine_arch_initcall(p3060_qds, swiotlb_setup_bus_notifier); +#endif -- 2.20.1