From 65bf53de830063520cfbdedd56d80f1125d62271 Mon Sep 17 00:00:00 2001 From: Ian Abbott Date: Fri, 20 May 2016 14:49:16 +0100 Subject: [PATCH] staging: comedi: drivers: re-do PLX PCI 9080 DMAMODEx register values Replace the existing macros in "plx9080.h" that define values for the DMAMODE0 and DMAMODE1 registers. Use the prefix `PLX_DMAMODE_` for the macros. Make use of the `BIT(x)` and `GENMASK(h,l)` macros to define the values. Signed-off-by: Ian Abbott Signed-off-by: Greg Kroah-Hartman --- drivers/staging/comedi/drivers/cb_pcidas64.c | 20 ++++---- drivers/staging/comedi/drivers/gsc_hpdi.c | 16 +++--- drivers/staging/comedi/drivers/plx9080.h | 52 +++++++++++++------- 3 files changed, 53 insertions(+), 35 deletions(-) diff --git a/drivers/staging/comedi/drivers/cb_pcidas64.c b/drivers/staging/comedi/drivers/cb_pcidas64.c index dfb2ae871227..48aca0652697 100644 --- a/drivers/staging/comedi/drivers/cb_pcidas64.c +++ b/drivers/staging/comedi/drivers/cb_pcidas64.c @@ -1308,28 +1308,28 @@ static void init_plx9080(struct comedi_device *dev) /* configure dma0 mode */ bits = 0; /* enable ready input, not sure if this is necessary */ - bits |= PLX_DMA_EN_READYIN_BIT; + bits |= PLX_DMAMODE_READYIEN; /* enable bterm, not sure if this is necessary */ - bits |= PLX_EN_BTERM_BIT; + bits |= PLX_DMAMODE_BTERMIEN; /* enable dma chaining */ - bits |= PLX_EN_CHAIN_BIT; + bits |= PLX_DMAMODE_CHAINEN; /* enable interrupt on dma done * (probably don't need this, since chain never finishes) */ - bits |= PLX_EN_DMA_DONE_INTR_BIT; + bits |= PLX_DMAMODE_DONEIEN; /* don't increment local address during transfers * (we are transferring from a fixed fifo register) */ - bits |= PLX_LOCAL_ADDR_CONST_BIT; + bits |= PLX_DMAMODE_LACONST; /* route dma interrupt to pci bus */ - bits |= PLX_DMA_INTR_PCI_BIT; + bits |= PLX_DMAMODE_INTRPCI; /* enable demand mode */ - bits |= PLX_DEMAND_MODE_BIT; + bits |= PLX_DMAMODE_DEMAND; /* enable local burst mode */ - bits |= PLX_DMA_LOCAL_BURST_EN_BIT; + bits |= PLX_DMAMODE_BURSTEN; /* 4020 uses 32 bit dma */ if (board->layout == LAYOUT_4020) - bits |= PLX_LOCAL_BUS_32_WIDE_BITS; + bits |= PLX_DMAMODE_WIDTH32; else /* localspace0 bus is 16 bits wide */ - bits |= PLX_LOCAL_BUS_16_WIDE_BITS; + bits |= PLX_DMAMODE_WIDTH16; writel(bits, plx_iobase + PLX_REG_DMAMODE1); if (ao_cmd_is_supported(board)) writel(bits, plx_iobase + PLX_REG_DMAMODE0); diff --git a/drivers/staging/comedi/drivers/gsc_hpdi.c b/drivers/staging/comedi/drivers/gsc_hpdi.c index e28879801085..d63dc46acfe2 100644 --- a/drivers/staging/comedi/drivers/gsc_hpdi.c +++ b/drivers/staging/comedi/drivers/gsc_hpdi.c @@ -563,26 +563,26 @@ static void gsc_hpdi_init_plx9080(struct comedi_device *dev) /* configure dma0 mode */ bits = 0; /* enable ready input */ - bits |= PLX_DMA_EN_READYIN_BIT; + bits |= PLX_DMAMODE_READYIEN; /* enable dma chaining */ - bits |= PLX_EN_CHAIN_BIT; + bits |= PLX_DMAMODE_CHAINEN; /* * enable interrupt on dma done * (probably don't need this, since chain never finishes) */ - bits |= PLX_EN_DMA_DONE_INTR_BIT; + bits |= PLX_DMAMODE_DONEIEN; /* * don't increment local address during transfers * (we are transferring from a fixed fifo register) */ - bits |= PLX_LOCAL_ADDR_CONST_BIT; + bits |= PLX_DMAMODE_LACONST; /* route dma interrupt to pci bus */ - bits |= PLX_DMA_INTR_PCI_BIT; + bits |= PLX_DMAMODE_INTRPCI; /* enable demand mode */ - bits |= PLX_DEMAND_MODE_BIT; + bits |= PLX_DMAMODE_DEMAND; /* enable local burst mode */ - bits |= PLX_DMA_LOCAL_BURST_EN_BIT; - bits |= PLX_LOCAL_BUS_32_WIDE_BITS; + bits |= PLX_DMAMODE_BURSTEN; + bits |= PLX_DMAMODE_WIDTH32; writel(bits, plx_iobase + PLX_REG_DMAMODE0); } diff --git a/drivers/staging/comedi/drivers/plx9080.h b/drivers/staging/comedi/drivers/plx9080.h index c70af5e500c8..99c075c8d174 100644 --- a/drivers/staging/comedi/drivers/plx9080.h +++ b/drivers/staging/comedi/drivers/plx9080.h @@ -457,23 +457,41 @@ struct plx_dma_desc { #define PLX_REG_DMAMODE0 0x0080 #define PLX_REG_DMAMODE1 0x0094 -#define PLX_LOCAL_BUS_16_WIDE_BITS 0x1 -#define PLX_LOCAL_BUS_32_WIDE_BITS 0x3 -#define PLX_LOCAL_BUS_WIDTH_MASK 0x3 -#define PLX_DMA_EN_READYIN_BIT 0x40 /* enable ready in input */ -#define PLX_EN_BTERM_BIT 0x80 /* enable BTERM# input */ -#define PLX_DMA_LOCAL_BURST_EN_BIT 0x100 /* enable local burst mode */ -#define PLX_EN_CHAIN_BIT 0x200 /* enables chaining */ -/* enables interrupt on dma done */ -#define PLX_EN_DMA_DONE_INTR_BIT 0x400 -/* hold local address constant (don't increment) */ -#define PLX_LOCAL_ADDR_CONST_BIT 0x800 -/* enables demand-mode for dma transfer */ -#define PLX_DEMAND_MODE_BIT 0x1000 -#define PLX_EOT_ENABLE_BIT 0x4000 -#define PLX_STOP_MODE_BIT 0x8000 -/* routes dma interrupt to pci bus (instead of local bus) */ -#define PLX_DMA_INTR_PCI_BIT 0x20000 +/* Local Bus Width */ +#define PLX_DMAMODE_WIDTH8 (BIT(0) * 0) /* 8 bits wide */ +#define PLX_DMAMODE_WIDTH16 (BIT(0) * 1) /* 16 bits wide */ +#define PLX_DMAMODE_WIDTH32 (BIT(0) * 2) /* 32 bits wide */ +#define PLX_DMAMODE_WIDTH32A (BIT(0) * 3) /* 32 bits wide */ +#define PLX_DMAMODE_WIDTH_MASK GENMASK(1, 0) +#define PLX_DMAMODE_WIDTH_SHIFT 0 +/* Internal Wait States */ +#define PLX_DMAMODE_IWS(x) (BIT(2) * ((x) & 0xf)) +#define PLX_DMAMODE_IWS_MASK GENMASK(5, 2) +#define PLX_DMAMODE_SHIFT 2 +/* Ready Input Enable */ +#define PLX_DMAMODE_READYIEN BIT(6) +/* BTERM# Input Enable */ +#define PLX_DMAMODE_BTERMIEN BIT(7) +/* Local Burst Enable */ +#define PLX_DMAMODE_BURSTEN BIT(8) +/* Chaining Enable */ +#define PLX_DMAMODE_CHAINEN BIT(9) +/* Done Interrupt Enable */ +#define PLX_DMAMODE_DONEIEN BIT(10) +/* Hold Local Address Constant */ +#define PLX_DMAMODE_LACONST BIT(11) +/* Demand Mode */ +#define PLX_DMAMODE_DEMAND BIT(12) +/* Write And Invalidate Mode */ +#define PLX_DMAMODE_WINVALIDATE BIT(13) +/* DMA EOT Enable - enables EOT0# or EOT1# input pin */ +#define PLX_DMAMODE_EOTEN BIT(14) +/* DMA Stop Data Transfer Mode - 0:BLAST; 1:EOT asserted or DREQ deasserted */ +#define PLX_DMAMODE_STOP BIT(15) +/* DMA Clear Count Mode - count in descriptor cleared on completion */ +#define PLX_DMAMODE_CLRCOUNT BIT(16) +/* DMA Channel Interrupt Select - 0:local bus interrupt; 1:PCI interrupt */ +#define PLX_DMAMODE_INTRPCI BIT(17) /* DMA Channel N PCI Address Register (N <= 1) */ #define PLX_REG_DMAPADR(n) ((n) ? PLX_REG_DMAPADR1 : PLX_REG_DMAPADR0) -- 2.20.1