From 5268ed9d2e3b52f703f3661eef14cecbb2b572d4 Mon Sep 17 00:00:00 2001 From: John Youn Date: Thu, 17 Dec 2015 11:16:31 -0800 Subject: [PATCH] usb: dwc2: Fix dr_mode validation The dr_mode parameter was being checked against how the dwc2 module was being configured at compile time. But it wasn't checked against the hardware capabilities, nor were the hardware capabilities checked against the compilation parameters. This commit adds those checks and adjusts dr_mode to an appropriate value, if needed. If the hardware capabilities and module compilation do not match then we fail as it wouldn't be possible to run properly. The hardware, module, and dr_mode, can each be set to host, device, or otg. Check that all these values are compatible and adjust the value of dr_mode if possible. The following table summarizes the behavior: actual HW MOD dr_mode dr_mode ------------------------------ HST HST any : HST HST DEV any : --- HST OTG any : HST DEV HST any : --- DEV DEV any : DEV DEV OTG any : DEV OTG HST any : HST OTG DEV any : DEV OTG OTG any : dr_mode Signed-off-by: John Youn Signed-off-by: Felipe Balbi --- drivers/usb/dwc2/platform.c | 82 +++++++++++++++++++++++++++++++------ 1 file changed, 69 insertions(+), 13 deletions(-) diff --git a/drivers/usb/dwc2/platform.c b/drivers/usb/dwc2/platform.c index 8bd7315a06c9..f4366513acb6 100644 --- a/drivers/usb/dwc2/platform.c +++ b/drivers/usb/dwc2/platform.c @@ -149,6 +149,71 @@ static const struct dwc2_core_params params_rk3066 = { .hibernation = -1, }; +/* + * Check the dr_mode against the module configuration and hardware + * capabilities. + * + * The hardware, module, and dr_mode, can each be set to host, device, + * or otg. Check that all these values are compatible and adjust the + * value of dr_mode if possible. + * + * actual + * HW MOD dr_mode dr_mode + * ------------------------------ + * HST HST any : HST + * HST DEV any : --- + * HST OTG any : HST + * + * DEV HST any : --- + * DEV DEV any : DEV + * DEV OTG any : DEV + * + * OTG HST any : HST + * OTG DEV any : DEV + * OTG OTG any : dr_mode + */ +static int dwc2_get_dr_mode(struct dwc2_hsotg *hsotg) +{ + enum usb_dr_mode mode; + + hsotg->dr_mode = usb_get_dr_mode(hsotg->dev); + if (hsotg->dr_mode == USB_DR_MODE_UNKNOWN) + hsotg->dr_mode = USB_DR_MODE_OTG; + + mode = hsotg->dr_mode; + + if (dwc2_hw_is_device(hsotg)) { + if (IS_ENABLED(CONFIG_USB_DWC2_HOST)) { + dev_err(hsotg->dev, + "Controller does not support host mode.\n"); + return -EINVAL; + } + mode = USB_DR_MODE_PERIPHERAL; + } else if (dwc2_hw_is_host(hsotg)) { + if (IS_ENABLED(CONFIG_USB_DWC2_PERIPHERAL)) { + dev_err(hsotg->dev, + "Controller does not support device mode.\n"); + return -EINVAL; + } + mode = USB_DR_MODE_HOST; + } else { + if (IS_ENABLED(CONFIG_USB_DWC2_HOST)) + mode = USB_DR_MODE_HOST; + else if (IS_ENABLED(CONFIG_USB_DWC2_PERIPHERAL)) + mode = USB_DR_MODE_PERIPHERAL; + } + + if (mode != hsotg->dr_mode) { + dev_warn(hsotg->dev, + "Configuration mismatch. dr_mode forced to %s\n", + mode == USB_DR_MODE_HOST ? "host" : "device"); + + hsotg->dr_mode = mode; + } + + return 0; +} + static int __dwc2_lowlevel_hw_enable(struct dwc2_hsotg *hsotg) { struct platform_device *pdev = to_platform_device(hsotg->dev); @@ -412,19 +477,6 @@ static int dwc2_driver_probe(struct platform_device *dev) dev_dbg(&dev->dev, "mapped PA %08lx to VA %p\n", (unsigned long)res->start, hsotg->regs); - hsotg->dr_mode = usb_get_dr_mode(&dev->dev); - if (IS_ENABLED(CONFIG_USB_DWC2_HOST) && - hsotg->dr_mode != USB_DR_MODE_HOST) { - hsotg->dr_mode = USB_DR_MODE_HOST; - dev_warn(hsotg->dev, - "Configuration mismatch. Forcing host mode\n"); - } else if (IS_ENABLED(CONFIG_USB_DWC2_PERIPHERAL) && - hsotg->dr_mode != USB_DR_MODE_PERIPHERAL) { - hsotg->dr_mode = USB_DR_MODE_PERIPHERAL; - dev_warn(hsotg->dev, - "Configuration mismatch. Forcing peripheral mode\n"); - } - retval = dwc2_lowlevel_hw_init(hsotg); if (retval) return retval; @@ -456,6 +508,10 @@ static int dwc2_driver_probe(struct platform_device *dev) if (retval) return retval; + retval = dwc2_get_dr_mode(hsotg); + if (retval) + return retval; + /* * Reset before dwc2_get_hwparams() then it could get power-on real * reset value form registers. -- 2.20.1