From 418d5516568b3fdbc4e7b53677dd78aed8514565 Mon Sep 17 00:00:00 2001 From: Linus Walleij Date: Mon, 1 Feb 2016 14:18:57 +0100 Subject: [PATCH] ARM: nomadik: fix up SD/MMC DT settings The DTSI file for the Nomadik does not properly specify how the PL180 levelshifter is connected: the Nomadik actually needs all the five st,sig-dir-* flags set to properly control all lines out. Further this board supports full power cycling of the card, and since this variant has no hardware clock gating, it needs a ridiculously low frequency setting to keep up with the ever overflowing FIFO. The pin configuration set-up is a bit of a mystery, because of course these pins are a mix of inputs and outputs. However the reference implementation sets all pins to "output" with unspecified initial value, so let's do that here as well. Cc: stable@vger.kernel.org Signed-off-by: Linus Walleij Acked-by: Ulf Hansson Signed-off-by: Olof Johansson --- arch/arm/boot/dts/ste-nomadik-stn8815.dtsi | 37 ++++++++++++---------- 1 file changed, 20 insertions(+), 17 deletions(-) diff --git a/arch/arm/boot/dts/ste-nomadik-stn8815.dtsi b/arch/arm/boot/dts/ste-nomadik-stn8815.dtsi index d0c743853318..27a333eb8987 100644 --- a/arch/arm/boot/dts/ste-nomadik-stn8815.dtsi +++ b/arch/arm/boot/dts/ste-nomadik-stn8815.dtsi @@ -127,22 +127,14 @@ }; mmcsd_default_mode: mmcsd_default { mmcsd_default_cfg1 { - /* MCCLK */ - pins = "GPIO8_B10"; - ste,output = <0>; - }; - mmcsd_default_cfg2 { - /* MCCMDDIR, MCDAT0DIR, MCDAT31DIR, MCDATDIR2 */ - pins = "GPIO10_C11", "GPIO15_A12", - "GPIO16_C13", "GPIO23_D15"; - ste,output = <1>; - }; - mmcsd_default_cfg3 { - /* MCCMD, MCDAT3-0, MCMSFBCLK */ - pins = "GPIO9_A10", "GPIO11_B11", - "GPIO12_A11", "GPIO13_C12", - "GPIO14_B12", "GPIO24_C15"; - ste,input = <1>; + /* + * MCCLK, MCCMDDIR, MCDAT0DIR, MCDAT31DIR, MCDATDIR2 + * MCCMD, MCDAT3-0, MCMSFBCLK + */ + pins = "GPIO8_B10", "GPIO9_A10", "GPIO10_C11", "GPIO11_B11", + "GPIO12_A11", "GPIO13_C12", "GPIO14_B12", "GPIO15_A12", + "GPIO16_C13", "GPIO23_D15", "GPIO24_C15"; + ste,output = <2>; }; }; }; @@ -802,10 +794,21 @@ clock-names = "mclk", "apb_pclk"; interrupt-parent = <&vica>; interrupts = <22>; - max-frequency = <48000000>; + max-frequency = <400000>; bus-width = <4>; cap-mmc-highspeed; cap-sd-highspeed; + full-pwr-cycle; + /* + * The STw4811 circuit used with the Nomadik strictly + * requires that all of these signal direction pins be + * routed and used for its 4-bit levelshifter. + */ + st,sig-dir-dat0; + st,sig-dir-dat2; + st,sig-dir-dat31; + st,sig-dir-cmd; + st,sig-pin-fbclk; pinctrl-names = "default"; pinctrl-0 = <&mmcsd_default_mux>, <&mmcsd_default_mode>; vmmc-supply = <&vmmc_regulator>; -- 2.20.1