From 414ed537995617f4cbcab65e193f26a2b2dcfa5e Mon Sep 17 00:00:00 2001 From: Dave Airlie Date: Tue, 16 Aug 2005 20:43:16 +1000 Subject: [PATCH] drm: add initial r300 3D support. This adds initial r300 3D support to the radeon DRM. From: Nicolai Haehnle, Vladimir Dergachev, and others. Signed-off-by: David Airlie --- drivers/char/drm/Makefile | 2 +- drivers/char/drm/drm_pciids.h | 13 + drivers/char/drm/r300_cmdbuf.c | 801 ++++++++++++++++++ drivers/char/drm/r300_reg.h | 1412 +++++++++++++++++++++++++++++++ drivers/char/drm/radeon_cp.c | 13 + drivers/char/drm/radeon_drm.h | 46 + drivers/char/drm/radeon_drv.h | 29 +- drivers/char/drm/radeon_state.c | 11 + 8 files changed, 2325 insertions(+), 2 deletions(-) create mode 100644 drivers/char/drm/r300_cmdbuf.c create mode 100644 drivers/char/drm/r300_reg.h diff --git a/drivers/char/drm/Makefile b/drivers/char/drm/Makefile index 1945138cb8fb..e41060c76226 100644 --- a/drivers/char/drm/Makefile +++ b/drivers/char/drm/Makefile @@ -14,7 +14,7 @@ mga-objs := mga_drv.o mga_dma.o mga_state.o mga_warp.o mga_irq.o i810-objs := i810_drv.o i810_dma.o i830-objs := i830_drv.o i830_dma.o i830_irq.o i915-objs := i915_drv.o i915_dma.o i915_irq.o i915_mem.o -radeon-objs := radeon_drv.o radeon_cp.o radeon_state.o radeon_mem.o radeon_irq.o +radeon-objs := radeon_drv.o radeon_cp.o radeon_state.o radeon_mem.o radeon_irq.o r300_cmdbuf.o ffb-objs := ffb_drv.o ffb_context.o sis-objs := sis_drv.o sis_ds.o sis_mm.o savage-objs := savage_drv.o savage_bci.o savage_state.o diff --git a/drivers/char/drm/drm_pciids.h b/drivers/char/drm/drm_pciids.h index 8e264f9c1a1e..1874c1fd1717 100644 --- a/drivers/char/drm/drm_pciids.h +++ b/drivers/char/drm/drm_pciids.h @@ -25,6 +25,8 @@ {0x1002, 0x4965, PCI_ANY_ID, PCI_ANY_ID, 0, 0, CHIP_R250}, \ {0x1002, 0x4966, PCI_ANY_ID, PCI_ANY_ID, 0, 0, CHIP_R250}, \ {0x1002, 0x4967, PCI_ANY_ID, PCI_ANY_ID, 0, 0, CHIP_R250}, \ + {0x1002, 0x4A49, PCI_ANY_ID, PCI_ANY_ID, 0, 0, CHIP_R420}, \ + {0x1002, 0x4A4B, PCI_ANY_ID, PCI_ANY_ID, 0, 0, CHIP_R420}, \ {0x1002, 0x4C57, PCI_ANY_ID, PCI_ANY_ID, 0, 0, CHIP_RV200|CHIP_IS_MOBILITY}, \ {0x1002, 0x4C58, PCI_ANY_ID, PCI_ANY_ID, 0, 0, CHIP_RV200|CHIP_IS_MOBILITY}, \ {0x1002, 0x4C59, PCI_ANY_ID, PCI_ANY_ID, 0, 0, CHIP_RV100|CHIP_IS_MOBILITY}, \ @@ -33,7 +35,17 @@ {0x1002, 0x4C65, PCI_ANY_ID, PCI_ANY_ID, 0, 0, CHIP_R250|CHIP_IS_MOBILITY}, \ {0x1002, 0x4C66, PCI_ANY_ID, PCI_ANY_ID, 0, 0, CHIP_R250|CHIP_IS_MOBILITY}, \ {0x1002, 0x4C67, PCI_ANY_ID, PCI_ANY_ID, 0, 0, CHIP_R250|CHIP_IS_MOBILITY}, \ + {0x1002, 0x4E44, PCI_ANY_ID, PCI_ANY_ID, 0, 0, CHIP_R300}, \ + {0x1002, 0x4E45, PCI_ANY_ID, PCI_ANY_ID, 0, 0, CHIP_R300}, \ + {0x1002, 0x4E46, PCI_ANY_ID, PCI_ANY_ID, 0, 0, CHIP_RV350}, \ + {0x1002, 0x4E47, PCI_ANY_ID, PCI_ANY_ID, 0, 0, CHIP_R300}, \ + {0x1002, 0x4E48, PCI_ANY_ID, PCI_ANY_ID, 0, 0, CHIP_R350}, \ + {0x1002, 0x4E49, PCI_ANY_ID, PCI_ANY_ID, 0, 0, CHIP_R350}, \ + {0x1002, 0x4E4A, PCI_ANY_ID, PCI_ANY_ID, 0, 0, CHIP_RV350}, \ + {0x1002, 0x4E4B, PCI_ANY_ID, PCI_ANY_ID, 0, 0, CHIP_R350}, \ {0x1002, 0x4E50, PCI_ANY_ID, PCI_ANY_ID, 0, 0, CHIP_RV350|CHIP_IS_MOBILITY}, \ + {0x1002, 0x4E51, PCI_ANY_ID, PCI_ANY_ID, 0, 0, CHIP_RV350|CHIP_IS_MOBILITY}, \ + {0x1002, 0x4E54, PCI_ANY_ID, PCI_ANY_ID, 0, 0, CHIP_RV350|CHIP_IS_MOBILITY}, \ {0x1002, 0x5144, PCI_ANY_ID, PCI_ANY_ID, 0, 0, CHIP_R100|CHIP_SINGLE_CRTC}, \ {0x1002, 0x5145, PCI_ANY_ID, PCI_ANY_ID, 0, 0, CHIP_R100|CHIP_SINGLE_CRTC}, \ {0x1002, 0x5146, PCI_ANY_ID, PCI_ANY_ID, 0, 0, CHIP_R100|CHIP_SINGLE_CRTC}, \ @@ -56,6 +68,7 @@ {0x1002, 0x516A, PCI_ANY_ID, PCI_ANY_ID, 0, 0, CHIP_R200}, \ {0x1002, 0x516B, PCI_ANY_ID, PCI_ANY_ID, 0, 0, CHIP_R200}, \ {0x1002, 0x516C, PCI_ANY_ID, PCI_ANY_ID, 0, 0, CHIP_R200}, \ + {0x1002, 0x5460, PCI_ANY_ID, PCI_ANY_ID, 0, 0, CHIP_RV350}, \ {0x1002, 0x5834, PCI_ANY_ID, PCI_ANY_ID, 0, 0, CHIP_RS300|CHIP_IS_IGP}, \ {0x1002, 0x5835, PCI_ANY_ID, PCI_ANY_ID, 0, 0, CHIP_RS300|CHIP_IS_IGP|CHIP_IS_MOBILITY}, \ {0x1002, 0x5836, PCI_ANY_ID, PCI_ANY_ID, 0, 0, CHIP_RS300|CHIP_IS_IGP}, \ diff --git a/drivers/char/drm/r300_cmdbuf.c b/drivers/char/drm/r300_cmdbuf.c new file mode 100644 index 000000000000..623f1f460cb5 --- /dev/null +++ b/drivers/char/drm/r300_cmdbuf.c @@ -0,0 +1,801 @@ +/* r300_cmdbuf.c -- Command buffer emission for R300 -*- linux-c -*- + * + * Copyright (C) The Weather Channel, Inc. 2002. + * Copyright (C) 2004 Nicolai Haehnle. + * All Rights Reserved. + * + * The Weather Channel (TM) funded Tungsten Graphics to develop the + * initial release of the Radeon 8500 driver under the XFree86 license. + * This notice must be preserved. + * + * Permission is hereby granted, free of charge, to any person obtaining a + * copy of this software and associated documentation files (the "Software"), + * to deal in the Software without restriction, including without limitation + * the rights to use, copy, modify, merge, publish, distribute, sublicense, + * and/or sell copies of the Software, and to permit persons to whom the + * Software is furnished to do so, subject to the following conditions: + * + * The above copyright notice and this permission notice (including the next + * paragraph) shall be included in all copies or substantial portions of the + * Software. + * + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR + * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, + * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL + * PRECISION INSIGHT AND/OR ITS SUPPLIERS BE LIABLE FOR ANY CLAIM, DAMAGES OR + * OTHER LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, + * ARISING FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER + * DEALINGS IN THE SOFTWARE. + * + * Authors: + * Nicolai Haehnle + */ + +#include "drmP.h" +#include "drm.h" +#include "radeon_drm.h" +#include "radeon_drv.h" +#include "r300_reg.h" + + +#define R300_SIMULTANEOUS_CLIPRECTS 4 + +/* Values for R300_RE_CLIPRECT_CNTL depending on the number of cliprects + */ +static const int r300_cliprect_cntl[4] = { + 0xAAAA, + 0xEEEE, + 0xFEFE, + 0xFFFE +}; + + +/** + * Emit up to R300_SIMULTANEOUS_CLIPRECTS cliprects from the given command + * buffer, starting with index n. + */ +static int r300_emit_cliprects(drm_radeon_private_t* dev_priv, + drm_radeon_cmd_buffer_t* cmdbuf, + int n) +{ + drm_clip_rect_t box; + int nr; + int i; + RING_LOCALS; + + nr = cmdbuf->nbox - n; + if (nr > R300_SIMULTANEOUS_CLIPRECTS) + nr = R300_SIMULTANEOUS_CLIPRECTS; + + DRM_DEBUG("%i cliprects\n", nr); + + if (nr) { + BEGIN_RING(6 + nr*2); + OUT_RING( CP_PACKET0( R300_RE_CLIPRECT_TL_0, nr*2 - 1 ) ); + + for(i = 0; i < nr; ++i) { + if (DRM_COPY_FROM_USER_UNCHECKED(&box, &cmdbuf->boxes[n+i], sizeof(box))) { + DRM_ERROR("copy cliprect faulted\n"); + return DRM_ERR(EFAULT); + } + + box.x1 = (box.x1 + R300_CLIPRECT_OFFSET) & R300_CLIPRECT_MASK; + box.y1 = (box.y1 + R300_CLIPRECT_OFFSET) & R300_CLIPRECT_MASK; + box.x2 = (box.x2 + R300_CLIPRECT_OFFSET) & R300_CLIPRECT_MASK; + box.y2 = (box.y2 + R300_CLIPRECT_OFFSET) & R300_CLIPRECT_MASK; + + OUT_RING((box.x1 << R300_CLIPRECT_X_SHIFT) | + (box.y1 << R300_CLIPRECT_Y_SHIFT)); + OUT_RING((box.x2 << R300_CLIPRECT_X_SHIFT) | + (box.y2 << R300_CLIPRECT_Y_SHIFT)); + } + + OUT_RING_REG( R300_RE_CLIPRECT_CNTL, r300_cliprect_cntl[nr-1] ); + + /* TODO/SECURITY: Force scissors to a safe value, otherwise the + * client might be able to trample over memory. + * The impact should be very limited, but I'd rather be safe than + * sorry. + */ + OUT_RING( CP_PACKET0( R300_RE_SCISSORS_TL, 1 ) ); + OUT_RING( 0 ); + OUT_RING( R300_SCISSORS_X_MASK | R300_SCISSORS_Y_MASK ); + ADVANCE_RING(); + } else { + /* Why we allow zero cliprect rendering: + * There are some commands in a command buffer that must be submitted + * even when there are no cliprects, e.g. DMA buffer discard + * or state setting (though state setting could be avoided by + * simulating a loss of context). + * + * Now since the cmdbuf interface is so chaotic right now (and is + * bound to remain that way for a bit until things settle down), + * it is basically impossible to filter out the commands that are + * necessary and those that aren't. + * + * So I choose the safe way and don't do any filtering at all; + * instead, I simply set up the engine so that all rendering + * can't produce any fragments. + */ + BEGIN_RING(2); + OUT_RING_REG( R300_RE_CLIPRECT_CNTL, 0 ); + ADVANCE_RING(); + } + + return 0; +} + +u8 r300_reg_flags[0x10000>>2]; + + +void r300_init_reg_flags(void) +{ + int i; + memset(r300_reg_flags, 0, 0x10000>>2); + #define ADD_RANGE_MARK(reg, count,mark) \ + for(i=((reg)>>2);i<((reg)>>2)+(count);i++)\ + r300_reg_flags[i]|=(mark); + + #define MARK_SAFE 1 + #define MARK_CHECK_OFFSET 2 + + #define ADD_RANGE(reg, count) ADD_RANGE_MARK(reg, count, MARK_SAFE) + + /* these match cmducs() command in r300_driver/r300/r300_cmdbuf.c */ + ADD_RANGE(R300_SE_VPORT_XSCALE, 6); + ADD_RANGE(0x2080, 1); + ADD_RANGE(R300_SE_VTE_CNTL, 2); + ADD_RANGE(0x2134, 2); + ADD_RANGE(0x2140, 1); + ADD_RANGE(R300_VAP_INPUT_CNTL_0, 2); + ADD_RANGE(0x21DC, 1); + ADD_RANGE(0x221C, 1); + ADD_RANGE(0x2220, 4); + ADD_RANGE(0x2288, 1); + ADD_RANGE(R300_VAP_OUTPUT_VTX_FMT_0, 2); + ADD_RANGE(R300_VAP_PVS_CNTL_1, 3); + ADD_RANGE(R300_GB_ENABLE, 1); + ADD_RANGE(R300_GB_MSPOS0, 5); + ADD_RANGE(R300_TX_ENABLE, 1); + ADD_RANGE(0x4200, 4); + ADD_RANGE(0x4214, 1); + ADD_RANGE(R300_RE_POINTSIZE, 1); + ADD_RANGE(0x4230, 3); + ADD_RANGE(R300_RE_LINE_CNT, 1); + ADD_RANGE(0x4238, 1); + ADD_RANGE(0x4260, 3); + ADD_RANGE(0x4274, 4); + ADD_RANGE(0x4288, 5); + ADD_RANGE(0x42A0, 1); + ADD_RANGE(R300_RE_ZBIAS_T_FACTOR, 4); + ADD_RANGE(0x42B4, 1); + ADD_RANGE(R300_RE_CULL_CNTL, 1); + ADD_RANGE(0x42C0, 2); + ADD_RANGE(R300_RS_CNTL_0, 2); + ADD_RANGE(R300_RS_INTERP_0, 8); + ADD_RANGE(R300_RS_ROUTE_0, 8); + ADD_RANGE(0x43A4, 2); + ADD_RANGE(0x43E8, 1); + ADD_RANGE(R300_PFS_CNTL_0, 3); + ADD_RANGE(R300_PFS_NODE_0, 4); + ADD_RANGE(R300_PFS_TEXI_0, 64); + ADD_RANGE(0x46A4, 5); + ADD_RANGE(R300_PFS_INSTR0_0, 64); + ADD_RANGE(R300_PFS_INSTR1_0, 64); + ADD_RANGE(R300_PFS_INSTR2_0, 64); + ADD_RANGE(R300_PFS_INSTR3_0, 64); + ADD_RANGE(0x4BC0, 1); + ADD_RANGE(0x4BC8, 3); + ADD_RANGE(R300_PP_ALPHA_TEST, 2); + ADD_RANGE(0x4BD8, 1); + ADD_RANGE(R300_PFS_PARAM_0_X, 64); + ADD_RANGE(0x4E00, 1); + ADD_RANGE(R300_RB3D_CBLEND, 2); + ADD_RANGE(R300_RB3D_COLORMASK, 1); + ADD_RANGE(0x4E10, 3); + ADD_RANGE_MARK(R300_RB3D_COLOROFFSET0, 1, MARK_CHECK_OFFSET); /* check offset */ + ADD_RANGE(R300_RB3D_COLORPITCH0, 1); + ADD_RANGE(0x4E50, 9); + ADD_RANGE(0x4E88, 1); + ADD_RANGE(0x4EA0, 2); + ADD_RANGE(R300_RB3D_ZSTENCIL_CNTL_0, 3); + ADD_RANGE(0x4F10, 4); + ADD_RANGE_MARK(R300_RB3D_DEPTHOFFSET, 1, MARK_CHECK_OFFSET); /* check offset */ + ADD_RANGE(R300_RB3D_DEPTHPITCH, 1); + ADD_RANGE(0x4F28, 1); + ADD_RANGE(0x4F30, 2); + ADD_RANGE(0x4F44, 1); + ADD_RANGE(0x4F54, 1); + + ADD_RANGE(R300_TX_FILTER_0, 16); + ADD_RANGE(R300_TX_UNK1_0, 16); + ADD_RANGE(R300_TX_SIZE_0, 16); + ADD_RANGE(R300_TX_FORMAT_0, 16); + /* Texture offset is dangerous and needs more checking */ + ADD_RANGE_MARK(R300_TX_OFFSET_0, 16, MARK_CHECK_OFFSET); + ADD_RANGE(R300_TX_UNK4_0, 16); + ADD_RANGE(R300_TX_BORDER_COLOR_0, 16); + + /* Sporadic registers used as primitives are emitted */ + ADD_RANGE(0x4f18, 1); + ADD_RANGE(R300_RB3D_DSTCACHE_CTLSTAT, 1); + ADD_RANGE(R300_VAP_INPUT_ROUTE_0_0, 8); + ADD_RANGE(R300_VAP_INPUT_ROUTE_1_0, 8); + +} + +static __inline__ int r300_check_range(unsigned reg, int count) +{ + int i; + if(reg & ~0xffff)return -1; + for(i=(reg>>2);i<(reg>>2)+count;i++) + if(r300_reg_flags[i]!=MARK_SAFE)return 1; + return 0; +} + + /* we expect offsets passed to the framebuffer to be either within video memory or + within AGP space */ +static __inline__ int r300_check_offset(drm_radeon_private_t* dev_priv, u32 offset) +{ + /* we realy want to check against end of video aperture + but this value is not being kept. + This code is correct for now (does the same thing as the + code that sets MC_FB_LOCATION) in radeon_cp.c */ + if((offset>=dev_priv->fb_location) && + (offsetgart_vm_start))return 0; + if((offset>=dev_priv->gart_vm_start) && + (offsetgart_vm_start+dev_priv->gart_size))return 0; + return 1; +} + +static __inline__ int r300_emit_carefully_checked_packet0(drm_radeon_private_t* dev_priv, + drm_radeon_cmd_buffer_t* cmdbuf, + drm_r300_cmd_header_t header) +{ + int reg; + int sz; + int i; + int values[64]; + RING_LOCALS; + + sz = header.packet0.count; + reg = (header.packet0.reghi << 8) | header.packet0.reglo; + + if((sz>64)||(sz<0)){ + DRM_ERROR("Cannot emit more than 64 values at a time (reg=%04x sz=%d)\n", reg, sz); + return DRM_ERR(EINVAL); + } + for(i=0;ibuf)[i]; + switch(r300_reg_flags[(reg>>2)+i]){ + case MARK_SAFE: + break; + case MARK_CHECK_OFFSET: + if(r300_check_offset(dev_priv, (u32)values[i])){ + DRM_ERROR("Offset failed range check (reg=%04x sz=%d)\n", reg, sz); + return DRM_ERR(EINVAL); + } + break; + default: + DRM_ERROR("Register %04x failed check as flag=%02x\n", reg+i*4, r300_reg_flags[(reg>>2)+i]); + return DRM_ERR(EINVAL); + } + } + + BEGIN_RING(1+sz); + OUT_RING( CP_PACKET0( reg, sz-1 ) ); + OUT_RING_TABLE( values, sz ); + ADVANCE_RING(); + + cmdbuf->buf += sz*4; + cmdbuf->bufsz -= sz*4; + + return 0; +} + +/** + * Emits a packet0 setting arbitrary registers. + * Called by r300_do_cp_cmdbuf. + * + * Note that checks are performed on contents and addresses of the registers + */ +static __inline__ int r300_emit_packet0(drm_radeon_private_t* dev_priv, + drm_radeon_cmd_buffer_t* cmdbuf, + drm_r300_cmd_header_t header) +{ + int reg; + int sz; + RING_LOCALS; + + sz = header.packet0.count; + reg = (header.packet0.reghi << 8) | header.packet0.reglo; + + if (!sz) + return 0; + + if (sz*4 > cmdbuf->bufsz) + return DRM_ERR(EINVAL); + + if (reg+sz*4 >= 0x10000){ + DRM_ERROR("No such registers in hardware reg=%04x sz=%d\n", reg, sz); + return DRM_ERR(EINVAL); + } + + if(r300_check_range(reg, sz)){ + /* go and check everything */ + return r300_emit_carefully_checked_packet0(dev_priv, cmdbuf, header); + } + /* the rest of the data is safe to emit, whatever the values the user passed */ + + BEGIN_RING(1+sz); + OUT_RING( CP_PACKET0( reg, sz-1 ) ); + OUT_RING_TABLE( (int __user*)cmdbuf->buf, sz ); + ADVANCE_RING(); + + cmdbuf->buf += sz*4; + cmdbuf->bufsz -= sz*4; + + return 0; +} + + +/** + * Uploads user-supplied vertex program instructions or parameters onto + * the graphics card. + * Called by r300_do_cp_cmdbuf. + */ +static __inline__ int r300_emit_vpu(drm_radeon_private_t* dev_priv, + drm_radeon_cmd_buffer_t* cmdbuf, + drm_r300_cmd_header_t header) +{ + int sz; + int addr; + RING_LOCALS; + + sz = header.vpu.count; + addr = (header.vpu.adrhi << 8) | header.vpu.adrlo; + + if (!sz) + return 0; + if (sz*16 > cmdbuf->bufsz) + return DRM_ERR(EINVAL); + + BEGIN_RING(5+sz*4); + /* Wait for VAP to come to senses.. */ + /* there is no need to emit it multiple times, (only once before VAP is programmed, + but this optimization is for later */ + OUT_RING_REG( R300_VAP_PVS_WAITIDLE, 0 ); + OUT_RING_REG( R300_VAP_PVS_UPLOAD_ADDRESS, addr ); + OUT_RING( CP_PACKET0_TABLE( R300_VAP_PVS_UPLOAD_DATA, sz*4 - 1 ) ); + OUT_RING_TABLE( (int __user*)cmdbuf->buf, sz*4 ); + + ADVANCE_RING(); + + cmdbuf->buf += sz*16; + cmdbuf->bufsz -= sz*16; + + return 0; +} + + +/** + * Emit a clear packet from userspace. + * Called by r300_emit_packet3. + */ +static __inline__ int r300_emit_clear(drm_radeon_private_t* dev_priv, + drm_radeon_cmd_buffer_t* cmdbuf) +{ + RING_LOCALS; + + if (8*4 > cmdbuf->bufsz) + return DRM_ERR(EINVAL); + + BEGIN_RING(10); + OUT_RING( CP_PACKET3( R200_3D_DRAW_IMMD_2, 8 ) ); + OUT_RING( R300_PRIM_TYPE_POINT|R300_PRIM_WALK_RING| + (1<buf, 8 ); + ADVANCE_RING(); + + cmdbuf->buf += 8*4; + cmdbuf->bufsz -= 8*4; + + return 0; +} + +static __inline__ int r300_emit_3d_load_vbpntr(drm_radeon_private_t* dev_priv, + drm_radeon_cmd_buffer_t* cmdbuf, + u32 header) +{ + int count, i,k; + #define MAX_ARRAY_PACKET 64 + u32 payload[MAX_ARRAY_PACKET]; + u32 narrays; + RING_LOCALS; + + count=(header>>16) & 0x3fff; + + if((count+1)>MAX_ARRAY_PACKET){ + DRM_ERROR("Too large payload in 3D_LOAD_VBPNTR (count=%d)\n", count); + return DRM_ERR(EINVAL); + } + memset(payload, 0, MAX_ARRAY_PACKET*4); + memcpy(payload, cmdbuf->buf+4, (count+1)*4); + + /* carefully check packet contents */ + + narrays=payload[0]; + k=0; + i=1; + while((kbuf += (count+2)*4; + cmdbuf->bufsz -= (count+2)*4; + + return 0; +} + +static __inline__ int r300_emit_raw_packet3(drm_radeon_private_t* dev_priv, + drm_radeon_cmd_buffer_t* cmdbuf) +{ + u32 header; + int count; + RING_LOCALS; + + if (4 > cmdbuf->bufsz) + return DRM_ERR(EINVAL); + + /* Fixme !! This simply emits a packet without much checking. + We need to be smarter. */ + + /* obtain first word - actual packet3 header */ + header = *(u32 __user*)cmdbuf->buf; + + /* Is it packet 3 ? */ + if( (header>>30)!=0x3 ) { + DRM_ERROR("Not a packet3 header (0x%08x)\n", header); + return DRM_ERR(EINVAL); + } + + count=(header>>16) & 0x3fff; + + /* Check again now that we know how much data to expect */ + if ((count+2)*4 > cmdbuf->bufsz){ + DRM_ERROR("Expected packet3 of length %d but have only %d bytes left\n", + (count+2)*4, cmdbuf->bufsz); + return DRM_ERR(EINVAL); + } + + /* Is it a packet type we know about ? */ + switch(header & 0xff00){ + case RADEON_3D_LOAD_VBPNTR: /* load vertex array pointers */ + return r300_emit_3d_load_vbpntr(dev_priv, cmdbuf, header); + + case RADEON_CP_3D_DRAW_IMMD_2: /* triggers drawing using in-packet vertex data */ + case RADEON_CP_3D_DRAW_VBUF_2: /* triggers drawing of vertex buffers setup elsewhere */ + case RADEON_CP_3D_DRAW_INDX_2: /* triggers drawing using indices to vertex buffer */ + case RADEON_CP_INDX_BUFFER: /* DRAW_INDX_2 without INDX_BUFFER seems to lock up the gpu */ + case RADEON_WAIT_FOR_IDLE: + case RADEON_CP_NOP: + /* these packets are safe */ + break; + default: + DRM_ERROR("Unknown packet3 header (0x%08x)\n", header); + return DRM_ERR(EINVAL); + } + + + BEGIN_RING(count+2); + OUT_RING(header); + OUT_RING_TABLE( (int __user*)(cmdbuf->buf+4), count+1); + ADVANCE_RING(); + + cmdbuf->buf += (count+2)*4; + cmdbuf->bufsz -= (count+2)*4; + + return 0; +} + + +/** + * Emit a rendering packet3 from userspace. + * Called by r300_do_cp_cmdbuf. + */ +static __inline__ int r300_emit_packet3(drm_radeon_private_t* dev_priv, + drm_radeon_cmd_buffer_t* cmdbuf, + drm_r300_cmd_header_t header) +{ + int n; + int ret; + char __user* orig_buf = cmdbuf->buf; + int orig_bufsz = cmdbuf->bufsz; + + /* This is a do-while-loop so that we run the interior at least once, + * even if cmdbuf->nbox is 0. Compare r300_emit_cliprects for rationale. + */ + n = 0; + do { + if (cmdbuf->nbox > R300_SIMULTANEOUS_CLIPRECTS) { + ret = r300_emit_cliprects(dev_priv, cmdbuf, n); + if (ret) + return ret; + + cmdbuf->buf = orig_buf; + cmdbuf->bufsz = orig_bufsz; + } + + switch(header.packet3.packet) { + case R300_CMD_PACKET3_CLEAR: + DRM_DEBUG("R300_CMD_PACKET3_CLEAR\n"); + ret = r300_emit_clear(dev_priv, cmdbuf); + if (ret) { + DRM_ERROR("r300_emit_clear failed\n"); + return ret; + } + break; + + case R300_CMD_PACKET3_RAW: + DRM_DEBUG("R300_CMD_PACKET3_RAW\n"); + ret = r300_emit_raw_packet3(dev_priv, cmdbuf); + if (ret) { + DRM_ERROR("r300_emit_raw_packet3 failed\n"); + return ret; + } + break; + + default: + DRM_ERROR("bad packet3 type %i at %p\n", + header.packet3.packet, + cmdbuf->buf - sizeof(header)); + return DRM_ERR(EINVAL); + } + + n += R300_SIMULTANEOUS_CLIPRECTS; + } while(n < cmdbuf->nbox); + + return 0; +} + +/* Some of the R300 chips seem to be extremely touchy about the two registers + * that are configured in r300_pacify. + * Among the worst offenders seems to be the R300 ND (0x4E44): When userspace + * sends a command buffer that contains only state setting commands and a + * vertex program/parameter upload sequence, this will eventually lead to a + * lockup, unless the sequence is bracketed by calls to r300_pacify. + * So we should take great care to *always* call r300_pacify before + * *anything* 3D related, and again afterwards. This is what the + * call bracket in r300_do_cp_cmdbuf is for. + */ + +/** + * Emit the sequence to pacify R300. + */ +static __inline__ void r300_pacify(drm_radeon_private_t* dev_priv) +{ + RING_LOCALS; + + BEGIN_RING(6); + OUT_RING( CP_PACKET0( R300_RB3D_DSTCACHE_CTLSTAT, 0 ) ); + OUT_RING( 0xa ); + OUT_RING( CP_PACKET0( 0x4f18, 0 ) ); + OUT_RING( 0x3 ); + OUT_RING( CP_PACKET3( RADEON_CP_NOP, 0 ) ); + OUT_RING( 0x0 ); + ADVANCE_RING(); +} + + +/** + * Called by r300_do_cp_cmdbuf to update the internal buffer age and state. + * The actual age emit is done by r300_do_cp_cmdbuf, which is why you must + * be careful about how this function is called. + */ +static void r300_discard_buffer(drm_device_t * dev, drm_buf_t * buf) +{ + drm_radeon_private_t *dev_priv = dev->dev_private; + drm_radeon_buf_priv_t *buf_priv = buf->dev_private; + + buf_priv->age = ++dev_priv->sarea_priv->last_dispatch; + buf->pending = 1; + buf->used = 0; +} + + +/** + * Parses and validates a user-supplied command buffer and emits appropriate + * commands on the DMA ring buffer. + * Called by the ioctl handler function radeon_cp_cmdbuf. + */ +int r300_do_cp_cmdbuf(drm_device_t* dev, + DRMFILE filp, + drm_file_t* filp_priv, + drm_radeon_cmd_buffer_t* cmdbuf) +{ + drm_radeon_private_t *dev_priv = dev->dev_private; + drm_device_dma_t *dma = dev->dma; + drm_buf_t *buf = NULL; + int emit_dispatch_age = 0; + int ret = 0; + + DRM_DEBUG("\n"); + + /* See the comment above r300_emit_begin3d for why this call must be here, + * and what the cleanup gotos are for. */ + r300_pacify(dev_priv); + + if (cmdbuf->nbox <= R300_SIMULTANEOUS_CLIPRECTS) { + ret = r300_emit_cliprects(dev_priv, cmdbuf, 0); + if (ret) + goto cleanup; + } + + while(cmdbuf->bufsz >= sizeof(drm_r300_cmd_header_t)) { + int idx; + drm_r300_cmd_header_t header; + + header.u = *(unsigned int *)cmdbuf->buf; + + cmdbuf->buf += sizeof(header); + cmdbuf->bufsz -= sizeof(header); + + switch(header.header.cmd_type) { + case R300_CMD_PACKET0: + DRM_DEBUG("R300_CMD_PACKET0\n"); + ret = r300_emit_packet0(dev_priv, cmdbuf, header); + if (ret) { + DRM_ERROR("r300_emit_packet0 failed\n"); + goto cleanup; + } + break; + + case R300_CMD_VPU: + DRM_DEBUG("R300_CMD_VPU\n"); + ret = r300_emit_vpu(dev_priv, cmdbuf, header); + if (ret) { + DRM_ERROR("r300_emit_vpu failed\n"); + goto cleanup; + } + break; + + case R300_CMD_PACKET3: + DRM_DEBUG("R300_CMD_PACKET3\n"); + ret = r300_emit_packet3(dev_priv, cmdbuf, header); + if (ret) { + DRM_ERROR("r300_emit_packet3 failed\n"); + goto cleanup; + } + break; + + case R300_CMD_END3D: + DRM_DEBUG("R300_CMD_END3D\n"); + /* TODO: + Ideally userspace driver should not need to issue this call, + i.e. the drm driver should issue it automatically and prevent + lockups. + + In practice, we do not understand why this call is needed and what + it does (except for some vague guesses that it has to do with cache + coherence) and so the user space driver does it. + + Once we are sure which uses prevent lockups the code could be moved + into the kernel and the userspace driver will not + need to use this command. + + Note that issuing this command does not hurt anything + except, possibly, performance */ + r300_pacify(dev_priv); + break; + + case R300_CMD_CP_DELAY: + /* simple enough, we can do it here */ + DRM_DEBUG("R300_CMD_CP_DELAY\n"); + { + int i; + RING_LOCALS; + + BEGIN_RING(header.delay.count); + for(i=0;i= dma->buf_count) { + DRM_ERROR("buffer index %d (of %d max)\n", + idx, dma->buf_count - 1); + ret = DRM_ERR(EINVAL); + goto cleanup; + } + + buf = dma->buflist[idx]; + if (buf->filp != filp || buf->pending) { + DRM_ERROR("bad buffer %p %p %d\n", + buf->filp, filp, buf->pending); + ret = DRM_ERR(EINVAL); + goto cleanup; + } + + emit_dispatch_age = 1; + r300_discard_buffer(dev, buf); + break; + + case R300_CMD_WAIT: + /* simple enough, we can do it here */ + DRM_DEBUG("R300_CMD_WAIT\n"); + if(header.wait.flags==0)break; /* nothing to do */ + + { + RING_LOCALS; + + BEGIN_RING(2); + OUT_RING( CP_PACKET0( RADEON_WAIT_UNTIL, 0 ) ); + OUT_RING( (header.wait.flags & 0xf)<<14 ); + ADVANCE_RING(); + } + break; + + default: + DRM_ERROR("bad cmd_type %i at %p\n", + header.header.cmd_type, + cmdbuf->buf - sizeof(header)); + ret = DRM_ERR(EINVAL); + goto cleanup; + } + } + + DRM_DEBUG("END\n"); + +cleanup: + r300_pacify(dev_priv); + + /* We emit the vertex buffer age here, outside the pacifier "brackets" + * for two reasons: + * (1) This may coalesce multiple age emissions into a single one and + * (2) more importantly, some chips lock up hard when scratch registers + * are written inside the pacifier bracket. + */ + if (emit_dispatch_age) { + RING_LOCALS; + + /* Emit the vertex buffer age */ + BEGIN_RING(2); + RADEON_DISPATCH_AGE(dev_priv->sarea_priv->last_dispatch); + ADVANCE_RING(); + } + + COMMIT_RING(); + + return ret; +} + diff --git a/drivers/char/drm/r300_reg.h b/drivers/char/drm/r300_reg.h new file mode 100644 index 000000000000..c3e7ca3dbe3d --- /dev/null +++ b/drivers/char/drm/r300_reg.h @@ -0,0 +1,1412 @@ +/************************************************************************** + +Copyright (C) 2004-2005 Nicolai Haehnle et al. + +Permission is hereby granted, free of charge, to any person obtaining a +copy of this software and associated documentation files (the "Software"), +to deal in the Software without restriction, including without limitation +on the rights to use, copy, modify, merge, publish, distribute, sub +license, and/or sell copies of the Software, and to permit persons to whom +the Software is furnished to do so, subject to the following conditions: + +The above copyright notice and this permission notice (including the next +paragraph) shall be included in all copies or substantial portions of the +Software. + +THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR +IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, +FITNESS FOR A PARTICULAR PURPOSE AND NON-INFRINGEMENT. IN NO EVENT SHALL +THE AUTHOR(S) AND/OR THEIR SUPPLIERS BE LIABLE FOR ANY CLAIM, +DAMAGES OR OTHER LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR +OTHERWISE, ARISING FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE +USE OR OTHER DEALINGS IN THE SOFTWARE. + +**************************************************************************/ + +#ifndef _R300_REG_H +#define _R300_REG_H + +#define R300_MC_INIT_MISC_LAT_TIMER 0x180 +# define R300_MC_MISC__MC_CPR_INIT_LAT_SHIFT 0 +# define R300_MC_MISC__MC_VF_INIT_LAT_SHIFT 4 +# define R300_MC_MISC__MC_DISP0R_INIT_LAT_SHIFT 8 +# define R300_MC_MISC__MC_DISP1R_INIT_LAT_SHIFT 12 +# define R300_MC_MISC__MC_FIXED_INIT_LAT_SHIFT 16 +# define R300_MC_MISC__MC_E2R_INIT_LAT_SHIFT 20 +# define R300_MC_MISC__MC_SAME_PAGE_PRIO_SHIFT 24 +# define R300_MC_MISC__MC_GLOBW_INIT_LAT_SHIFT 28 + + +#define R300_MC_INIT_GFX_LAT_TIMER 0x154 +# define R300_MC_MISC__MC_G3D0R_INIT_LAT_SHIFT 0 +# define R300_MC_MISC__MC_G3D1R_INIT_LAT_SHIFT 4 +# define R300_MC_MISC__MC_G3D2R_INIT_LAT_SHIFT 8 +# define R300_MC_MISC__MC_G3D3R_INIT_LAT_SHIFT 12 +# define R300_MC_MISC__MC_TX0R_INIT_LAT_SHIFT 16 +# define R300_MC_MISC__MC_TX1R_INIT_LAT_SHIFT 20 +# define R300_MC_MISC__MC_GLOBR_INIT_LAT_SHIFT 24 +# define R300_MC_MISC__MC_GLOBW_FULL_LAT_SHIFT 28 + +/* +This file contains registers and constants for the R300. They have been +found mostly by examining command buffers captured using glxtest, as well +as by extrapolating some known registers and constants from the R200. + +I am fairly certain that they are correct unless stated otherwise in comments. +*/ + +#define R300_SE_VPORT_XSCALE 0x1D98 +#define R300_SE_VPORT_XOFFSET 0x1D9C +#define R300_SE_VPORT_YSCALE 0x1DA0 +#define R300_SE_VPORT_YOFFSET 0x1DA4 +#define R300_SE_VPORT_ZSCALE 0x1DA8 +#define R300_SE_VPORT_ZOFFSET 0x1DAC + + +/* This register is written directly and also starts data section in many 3d CP_PACKET3's */ +#define R300_VAP_VF_CNTL 0x2084 + +# define R300_VAP_VF_CNTL__PRIM_TYPE__SHIFT 0 +# define R300_VAP_VF_CNTL__PRIM_NONE (0<<0) +# define R300_VAP_VF_CNTL__PRIM_POINTS (1<<0) +# define R300_VAP_VF_CNTL__PRIM_LINES (2<<0) +# define R300_VAP_VF_CNTL__PRIM_LINE_STRIP (3<<0) +# define R300_VAP_VF_CNTL__PRIM_TRIANGLES (4<<0) +# define R300_VAP_VF_CNTL__PRIM_TRIANGLE_FAN (5<<0) +# define R300_VAP_VF_CNTL__PRIM_TRIANGLE_STRIP (6<<0) +# define R300_VAP_VF_CNTL__PRIM_LINE_LOOP (12<<0) +# define R300_VAP_VF_CNTL__PRIM_QUADS (13<<0) +# define R300_VAP_VF_CNTL__PRIM_QUAD_STRIP (14<<0) +# define R300_VAP_VF_CNTL__PRIM_POLYGON (15<<0) + +# define R300_VAP_VF_CNTL__PRIM_WALK__SHIFT 4 + /* State based - direct writes to registers trigger vertex generation */ +# define R300_VAP_VF_CNTL__PRIM_WALK_STATE_BASED (0<<4) +# define R300_VAP_VF_CNTL__PRIM_WALK_INDICES (1<<4) +# define R300_VAP_VF_CNTL__PRIM_WALK_VERTEX_LIST (2<<4) +# define R300_VAP_VF_CNTL__PRIM_WALK_VERTEX_EMBEDDED (3<<4) + + /* I don't think I saw these three used.. */ +# define R300_VAP_VF_CNTL__COLOR_ORDER__SHIFT 6 +# define R300_VAP_VF_CNTL__TCL_OUTPUT_CTL_ENA__SHIFT 9 +# define R300_VAP_VF_CNTL__PROG_STREAM_ENA__SHIFT 10 + + /* index size - when not set the indices are assumed to be 16 bit */ +# define R300_VAP_VF_CNTL__INDEX_SIZE_32bit (1<<11) + /* number of vertices */ +# define R300_VAP_VF_CNTL__NUM_VERTICES__SHIFT 16 + +/* BEGIN: Wild guesses */ +#define R300_VAP_OUTPUT_VTX_FMT_0 0x2090 +# define R300_VAP_OUTPUT_VTX_FMT_0__POS_PRESENT (1<<0) +# define R300_VAP_OUTPUT_VTX_FMT_0__COLOR_PRESENT (1<<1) +# define R300_VAP_OUTPUT_VTX_FMT_0__COLOR_1_PRESENT (1<<2) /* GUESS */ +# define R300_VAP_OUTPUT_VTX_FMT_0__COLOR_2_PRESENT (1<<3) /* GUESS */ +# define R300_VAP_OUTPUT_VTX_FMT_0__COLOR_3_PRESENT (1<<4) /* GUESS */ +# define R300_VAP_OUTPUT_VTX_FMT_0__PT_SIZE_PRESENT (1<<16) /* GUESS */ + +#define R300_VAP_OUTPUT_VTX_FMT_1 0x2094 +# define R300_VAP_OUTPUT_VTX_FMT_1__TEX_0_COMP_CNT_SHIFT 0 +# define R300_VAP_OUTPUT_VTX_FMT_1__TEX_1_COMP_CNT_SHIFT 3 +# define R300_VAP_OUTPUT_VTX_FMT_1__TEX_2_COMP_CNT_SHIFT 6 +# define R300_VAP_OUTPUT_VTX_FMT_1__TEX_3_COMP_CNT_SHIFT 9 +# define R300_VAP_OUTPUT_VTX_FMT_1__TEX_4_COMP_CNT_SHIFT 12 +# define R300_VAP_OUTPUT_VTX_FMT_1__TEX_5_COMP_CNT_SHIFT 15 +# define R300_VAP_OUTPUT_VTX_FMT_1__TEX_6_COMP_CNT_SHIFT 18 +# define R300_VAP_OUTPUT_VTX_FMT_1__TEX_7_COMP_CNT_SHIFT 21 +/* END */ + +#define R300_SE_VTE_CNTL 0x20b0 +# define R300_VPORT_X_SCALE_ENA 0x00000001 +# define R300_VPORT_X_OFFSET_ENA 0x00000002 +# define R300_VPORT_Y_SCALE_ENA 0x00000004 +# define R300_VPORT_Y_OFFSET_ENA 0x00000008 +# define R300_VPORT_Z_SCALE_ENA 0x00000010 +# define R300_VPORT_Z_OFFSET_ENA 0x00000020 +# define R300_VTX_XY_FMT 0x00000100 +# define R300_VTX_Z_FMT 0x00000200 +# define R300_VTX_W0_FMT 0x00000400 +# define R300_VTX_W0_NORMALIZE 0x00000800 +# define R300_VTX_ST_DENORMALIZED 0x00001000 + +/* BEGIN: Vertex data assembly - lots of uncertainties */ +/* gap */ +/* Where do we get our vertex data? +// +// Vertex data either comes either from immediate mode registers or from +// vertex arrays. +// There appears to be no mixed mode (though we can force the pitch of +// vertex arrays to 0, effectively reusing the same element over and over +// again). +// +// Immediate mode is controlled by the INPUT_CNTL registers. I am not sure +// if these registers influence vertex array processing. +// +// Vertex arrays are controlled via the 3D_LOAD_VBPNTR packet3. +// +// In both cases, vertex attributes are then passed through INPUT_ROUTE. + +// Beginning with INPUT_ROUTE_0_0 is a list of WORDs that route vertex data +// into the vertex processor's input registers. +// The first word routes the first input, the second word the second, etc. +// The corresponding input is routed into the register with the given index. +// The list is ended by a word with INPUT_ROUTE_END set. +// +// Always set COMPONENTS_4 in immediate mode. */ + +#define R300_VAP_INPUT_ROUTE_0_0 0x2150 +# define R300_INPUT_ROUTE_COMPONENTS_1 (0 << 0) +# define R300_INPUT_ROUTE_COMPONENTS_2 (1 << 0) +# define R300_INPUT_ROUTE_COMPONENTS_3 (2 << 0) +# define R300_INPUT_ROUTE_COMPONENTS_4 (3 << 0) +# define R300_INPUT_ROUTE_COMPONENTS_RGBA (4 << 0) /* GUESS */ +# define R300_VAP_INPUT_ROUTE_IDX_SHIFT 8 +# define R300_VAP_INPUT_ROUTE_IDX_MASK (31 << 8) /* GUESS */ +# define R300_VAP_INPUT_ROUTE_END (1 << 13) +# define R300_INPUT_ROUTE_IMMEDIATE_MODE (0 << 14) /* GUESS */ +# define R300_INPUT_ROUTE_FLOAT (1 << 14) /* GUESS */ +# define R300_INPUT_ROUTE_UNSIGNED_BYTE (2 << 14) /* GUESS */ +# define R300_INPUT_ROUTE_FLOAT_COLOR (3 << 14) /* GUESS */ +#define R300_VAP_INPUT_ROUTE_0_1 0x2154 +#define R300_VAP_INPUT_ROUTE_0_2 0x2158 +#define R300_VAP_INPUT_ROUTE_0_3 0x215C +#define R300_VAP_INPUT_ROUTE_0_4 0x2160 +#define R300_VAP_INPUT_ROUTE_0_5 0x2164 +#define R300_VAP_INPUT_ROUTE_0_6 0x2168 +#define R300_VAP_INPUT_ROUTE_0_7 0x216C + +/* gap */ +/* Notes: +// - always set up to produce at least two attributes: +// if vertex program uses only position, fglrx will set normal, too +// - INPUT_CNTL_0_COLOR and INPUT_CNTL_COLOR bits are always equal */ +#define R300_VAP_INPUT_CNTL_0 0x2180 +# define R300_INPUT_CNTL_0_COLOR 0x00000001 +#define R300_VAP_INPUT_CNTL_1 0x2184 +# define R300_INPUT_CNTL_POS 0x00000001 +# define R300_INPUT_CNTL_NORMAL 0x00000002 +# define R300_INPUT_CNTL_COLOR 0x00000004 +# define R300_INPUT_CNTL_TC0 0x00000400 +# define R300_INPUT_CNTL_TC1 0x00000800 +# define R300_INPUT_CNTL_TC2 0x00001000 /* GUESS */ +# define R300_INPUT_CNTL_TC3 0x00002000 /* GUESS */ +# define R300_INPUT_CNTL_TC4 0x00004000 /* GUESS */ +# define R300_INPUT_CNTL_TC5 0x00008000 /* GUESS */ +# define R300_INPUT_CNTL_TC6 0x00010000 /* GUESS */ +# define R300_INPUT_CNTL_TC7 0x00020000 /* GUESS */ + +/* gap */ +/* Words parallel to INPUT_ROUTE_0; All words that are active in INPUT_ROUTE_0 +// are set to a swizzling bit pattern, other words are 0. +// +// In immediate mode, the pattern is always set to xyzw. In vertex array +// mode, the swizzling pattern is e.g. used to set zw components in texture +// coordinates with only tweo components. */ +#define R300_VAP_INPUT_ROUTE_1_0 0x21E0 +# define R300_INPUT_ROUTE_SELECT_X 0 +# define R300_INPUT_ROUTE_SELECT_Y 1 +# define R300_INPUT_ROUTE_SELECT_Z 2 +# define R300_INPUT_ROUTE_SELECT_W 3 +# define R300_INPUT_ROUTE_SELECT_ZERO 4 +# define R300_INPUT_ROUTE_SELECT_ONE 5 +# define R300_INPUT_ROUTE_SELECT_MASK 7 +# define R300_INPUT_ROUTE_X_SHIFT 0 +# define R300_INPUT_ROUTE_Y_SHIFT 3 +# define R300_INPUT_ROUTE_Z_SHIFT 6 +# define R300_INPUT_ROUTE_W_SHIFT 9 +# define R300_INPUT_ROUTE_ENABLE (15 << 12) +#define R300_VAP_INPUT_ROUTE_1_1 0x21E4 +#define R300_VAP_INPUT_ROUTE_1_2 0x21E8 +#define R300_VAP_INPUT_ROUTE_1_3 0x21EC +#define R300_VAP_INPUT_ROUTE_1_4 0x21F0 +#define R300_VAP_INPUT_ROUTE_1_5 0x21F4 +#define R300_VAP_INPUT_ROUTE_1_6 0x21F8 +#define R300_VAP_INPUT_ROUTE_1_7 0x21FC + +/* END */ + +/* gap */ +/* BEGIN: Upload vertex program and data +// The programmable vertex shader unit has a memory bank of unknown size +// that can be written to in 16 byte units by writing the address into +// UPLOAD_ADDRESS, followed by data in UPLOAD_DATA (multiples of 4 DWORDs). +// +// Pointers into the memory bank are always in multiples of 16 bytes. +// +// The memory bank is divided into areas with fixed meaning. +// +// Starting at address UPLOAD_PROGRAM: Vertex program instructions. +// Native limits reported by drivers from ATI suggest size 256 (i.e. 4KB), +// whereas the difference between known addresses suggests size 512. +// +// Starting at address UPLOAD_PARAMETERS: Vertex program parameters. +// Native reported limits and the VPI layout suggest size 256, whereas +// difference between known addresses suggests size 512. +// +// At address UPLOAD_POINTSIZE is a vector (0, 0, ps, 0), where ps is the +// floating point pointsize. The exact purpose of this state is uncertain, +// as there is also the R300_RE_POINTSIZE register. +// +// Multiple vertex programs and parameter sets can be loaded at once, +// which could explain the size discrepancy. */ +#define R300_VAP_PVS_UPLOAD_ADDRESS 0x2200 +# define R300_PVS_UPLOAD_PROGRAM 0x00000000 +# define R300_PVS_UPLOAD_PARAMETERS 0x00000200 +# define R300_PVS_UPLOAD_POINTSIZE 0x00000406 +/* gap */ +#define R300_VAP_PVS_UPLOAD_DATA 0x2208 +/* END */ + +/* gap */ +/* I do not know the purpose of this register. However, I do know that +// it is set to 221C_CLEAR for clear operations and to 221C_NORMAL +// for normal rendering. */ +#define R300_VAP_UNKNOWN_221C 0x221C +# define R300_221C_NORMAL 0x00000000 +# define R300_221C_CLEAR 0x0001C000 + +/* gap */ +/* Sometimes, END_OF_PKT and 0x2284=0 are the only commands sent between +// rendering commands and overwriting vertex program parameters. +// Therefore, I suspect writing zero to 0x2284 synchronizes the engine and +// avoids bugs caused by still running shaders reading bad data from memory. */ +#define R300_VAP_PVS_WAITIDLE 0x2284 /* GUESS */ + +/* Absolutely no clue what this register is about. */ +#define R300_VAP_UNKNOWN_2288 0x2288 +# define R300_2288_R300 0x00750000 /* -- nh */ +# define R300_2288_RV350 0x0000FFFF /* -- Vladimir */ + +/* gap */ +/* Addresses are relative to the vertex program instruction area of the +// memory bank. PROGRAM_END points to the last instruction of the active +// program +// +// The meaning of the two UNKNOWN fields is obviously not known. However, +// experiments so far have shown that both *must* point to an instruction +// inside the vertex program, otherwise the GPU locks up. +// fglrx usually sets CNTL_3_UNKNOWN to the end of the program and +// CNTL_1_UNKNOWN points to instruction where last write to position takes place. +// Most likely this is used to ignore rest of the program in cases where group of verts arent visible. +// For some reason this "section" is sometimes accepted other instruction that have +// no relationship with position calculations. +*/ +#define R300_VAP_PVS_CNTL_1 0x22D0 +# define R300_PVS_CNTL_1_PROGRAM_START_SHIFT 0 +# define R300_PVS_CNTL_1_POS_END_SHIFT 10 +# define R300_PVS_CNTL_1_PROGRAM_END_SHIFT 20 +/* Addresses are relative the the vertex program parameters area. */ +#define R300_VAP_PVS_CNTL_2 0x22D4 +# define R300_PVS_CNTL_2_PARAM_OFFSET_SHIFT 0 +# define R300_PVS_CNTL_2_PARAM_COUNT_SHIFT 16 +#define R300_VAP_PVS_CNTL_3 0x22D8 +# define R300_PVS_CNTL_3_PROGRAM_UNKNOWN_SHIFT 10 +# define R300_PVS_CNTL_3_PROGRAM_UNKNOWN2_SHIFT 0 + +/* The entire range from 0x2300 to 0x2AC inclusive seems to be used for +// immediate vertices */ +#define R300_VAP_VTX_COLOR_R 0x2464 +#define R300_VAP_VTX_COLOR_G 0x2468 +#define R300_VAP_VTX_COLOR_B 0x246C +#define R300_VAP_VTX_POS_0_X_1 0x2490 /* used for glVertex2*() */ +#define R300_VAP_VTX_POS_0_Y_1 0x2494 +#define R300_VAP_VTX_COLOR_PKD 0x249C /* RGBA */ +#define R300_VAP_VTX_POS_0_X_2 0x24A0 /* used for glVertex3*() */ +#define R300_VAP_VTX_POS_0_Y_2 0x24A4 +#define R300_VAP_VTX_POS_0_Z_2 0x24A8 +#define R300_VAP_VTX_END_OF_PKT 0x24AC /* write 0 to indicate end of packet? */ + +/* gap */ + +/* These are values from r300_reg/r300_reg.h - they are known to be correct + and are here so we can use one register file instead of several + - Vladimir */ +#define R300_GB_VAP_RASTER_VTX_FMT_0 0x4000 +# define R300_GB_VAP_RASTER_VTX_FMT_0__POS_PRESENT (1<<0) +# define R300_GB_VAP_RASTER_VTX_FMT_0__COLOR_0_PRESENT (1<<1) +# define R300_GB_VAP_RASTER_VTX_FMT_0__COLOR_1_PRESENT (1<<2) +# define R300_GB_VAP_RASTER_VTX_FMT_0__COLOR_2_PRESENT (1<<3) +# define R300_GB_VAP_RASTER_VTX_FMT_0__COLOR_3_PRESENT (1<<4) +# define R300_GB_VAP_RASTER_VTX_FMT_0__COLOR_SPACE (0xf<<5) +# define R300_GB_VAP_RASTER_VTX_FMT_0__PT_SIZE_PRESENT (0x1<<16) + +#define R300_GB_VAP_RASTER_VTX_FMT_1 0x4004 + /* each of the following is 3 bits wide, specifies number + of components */ +# define R300_GB_VAP_RASTER_VTX_FMT_1__TEX_0_COMP_CNT_SHIFT 0 +# define R300_GB_VAP_RASTER_VTX_FMT_1__TEX_1_COMP_CNT_SHIFT 3 +# define R300_GB_VAP_RASTER_VTX_FMT_1__TEX_2_COMP_CNT_SHIFT 6 +# define R300_GB_VAP_RASTER_VTX_FMT_1__TEX_3_COMP_CNT_SHIFT 9 +# define R300_GB_VAP_RASTER_VTX_FMT_1__TEX_4_COMP_CNT_SHIFT 12 +# define R300_GB_VAP_RASTER_VTX_FMT_1__TEX_5_COMP_CNT_SHIFT 15 +# define R300_GB_VAP_RASTER_VTX_FMT_1__TEX_6_COMP_CNT_SHIFT 18 +# define R300_GB_VAP_RASTER_VTX_FMT_1__TEX_7_COMP_CNT_SHIFT 21 + +/* UNK30 seems to enables point to quad transformation on textures + (or something closely related to that). + This bit is rather fatal at the time being due to lackings at pixel shader side */ +#define R300_GB_ENABLE 0x4008 +# define R300_GB_POINT_STUFF_ENABLE (1<<0) +# define R300_GB_LINE_STUFF_ENABLE (1<<1) +# define R300_GB_TRIANGLE_STUFF_ENABLE (1<<2) +# define R300_GB_STENCIL_AUTO_ENABLE (1<<4) +# define R300_GB_UNK30 (1<<30) + /* each of the following is 2 bits wide */ +#define R300_GB_TEX_REPLICATE 0 +#define R300_GB_TEX_ST 1 +#define R300_GB_TEX_STR 2 +# define R300_GB_TEX0_SOURCE_SHIFT 16 +# define R300_GB_TEX1_SOURCE_SHIFT 18 +# define R300_GB_TEX2_SOURCE_SHIFT 20 +# define R300_GB_TEX3_SOURCE_SHIFT 22 +# define R300_GB_TEX4_SOURCE_SHIFT 24 +# define R300_GB_TEX5_SOURCE_SHIFT 26 +# define R300_GB_TEX6_SOURCE_SHIFT 28 +# define R300_GB_TEX7_SOURCE_SHIFT 30 + +/* MSPOS - positions for multisample antialiasing (?) */ +#define R300_GB_MSPOS0 0x4010 + /* shifts - each of the fields is 4 bits */ +# define R300_GB_MSPOS0__MS_X0_SHIFT 0 +# define R300_GB_MSPOS0__MS_Y0_SHIFT 4 +# define R300_GB_MSPOS0__MS_X1_SHIFT 8 +# define R300_GB_MSPOS0__MS_Y1_SHIFT 12 +# define R300_GB_MSPOS0__MS_X2_SHIFT 16 +# define R300_GB_MSPOS0__MS_Y2_SHIFT 20 +# define R300_GB_MSPOS0__MSBD0_Y 24 +# define R300_GB_MSPOS0__MSBD0_X 28 + +#define R300_GB_MSPOS1 0x4014 +# define R300_GB_MSPOS1__MS_X3_SHIFT 0 +# define R300_GB_MSPOS1__MS_Y3_SHIFT 4 +# define R300_GB_MSPOS1__MS_X4_SHIFT 8 +# define R300_GB_MSPOS1__MS_Y4_SHIFT 12 +# define R300_GB_MSPOS1__MS_X5_SHIFT 16 +# define R300_GB_MSPOS1__MS_Y5_SHIFT 20 +# define R300_GB_MSPOS1__MSBD1 24 + + +#define R300_GB_TILE_CONFIG 0x4018 +# define R300_GB_TILE_ENABLE (1<<0) +# define R300_GB_TILE_PIPE_COUNT_RV300 0 +# define R300_GB_TILE_PIPE_COUNT_R300 (3<<1) +# define R300_GB_TILE_PIPE_COUNT_R420 (7<<1) +# define R300_GB_TILE_SIZE_8 0 +# define R300_GB_TILE_SIZE_16 (1<<4) +# define R300_GB_TILE_SIZE_32 (2<<4) +# define R300_GB_SUPER_SIZE_1 (0<<6) +# define R300_GB_SUPER_SIZE_2 (1<<6) +# define R300_GB_SUPER_SIZE_4 (2<<6) +# define R300_GB_SUPER_SIZE_8 (3<<6) +# define R300_GB_SUPER_SIZE_16 (4<<6) +# define R300_GB_SUPER_SIZE_32 (5<<6) +# define R300_GB_SUPER_SIZE_64 (6<<6) +# define R300_GB_SUPER_SIZE_128 (7<<6) +# define R300_GB_SUPER_X_SHIFT 9 /* 3 bits wide */ +# define R300_GB_SUPER_Y_SHIFT 12 /* 3 bits wide */ +# define R300_GB_SUPER_TILE_A 0 +# define R300_GB_SUPER_TILE_B (1<<15) +# define R300_GB_SUBPIXEL_1_12 0 +# define R300_GB_SUBPIXEL_1_16 (1<<16) + +#define R300_GB_FIFO_SIZE 0x4024 + /* each of the following is 2 bits wide */ +#define R300_GB_FIFO_SIZE_32 0 +#define R300_GB_FIFO_SIZE_64 1 +#define R300_GB_FIFO_SIZE_128 2 +#define R300_GB_FIFO_SIZE_256 3 +# define R300_SC_IFIFO_SIZE_SHIFT 0 +# define R300_SC_TZFIFO_SIZE_SHIFT 2 +# define R300_SC_BFIFO_SIZE_SHIFT 4 + +# define R300_US_OFIFO_SIZE_SHIFT 12 +# define R300_US_WFIFO_SIZE_SHIFT 14 + /* the following use the same constants as above, but meaning is + is times 2 (i.e. instead of 32 words it means 64 */ +# define R300_RS_TFIFO_SIZE_SHIFT 6 +# define R300_RS_CFIFO_SIZE_SHIFT 8 +# define R300_US_RAM_SIZE_SHIFT 10 + /* watermarks, 3 bits wide */ +# define R300_RS_HIGHWATER_COL_SHIFT 16 +# define R300_RS_HIGHWATER_TEX_SHIFT 19 +# define R300_OFIFO_HIGHWATER_SHIFT 22 /* two bits only */ +# define R300_CUBE_FIFO_HIGHWATER_COL_SHIFT 24 + +#define R300_GB_SELECT 0x401C +# define R300_GB_FOG_SELECT_C0A 0 +# define R300_GB_FOG_SELECT_C1A 1 +# define R300_GB_FOG_SELECT_C2A 2 +# define R300_GB_FOG_SELECT_C3A 3 +# define R300_GB_FOG_SELECT_1_1_W 4 +# define R300_GB_FOG_SELECT_Z 5 +# define R300_GB_DEPTH_SELECT_Z 0 +# define R300_GB_DEPTH_SELECT_1_1_W (1<<3) +# define R300_GB_W_SELECT_1_W 0 +# define R300_GB_W_SELECT_1 (1<<4) + +#define R300_GB_AA_CONFIG 0x4020 +# define R300_AA_ENABLE 0x01 +# define R300_AA_SUBSAMPLES_2 0 +# define R300_AA_SUBSAMPLES_3 (1<<1) +# define R300_AA_SUBSAMPLES_4 (2<<1) +# define R300_AA_SUBSAMPLES_6 (3<<1) + +/* END */ + +/* gap */ +/* The upper enable bits are guessed, based on fglrx reported limits. */ +#define R300_TX_ENABLE 0x4104 +# define R300_TX_ENABLE_0 (1 << 0) +# define R300_TX_ENABLE_1 (1 << 1) +# define R300_TX_ENABLE_2 (1 << 2) +# define R300_TX_ENABLE_3 (1 << 3) +# define R300_TX_ENABLE_4 (1 << 4) +# define R300_TX_ENABLE_5 (1 << 5) +# define R300_TX_ENABLE_6 (1 << 6) +# define R300_TX_ENABLE_7 (1 << 7) +# define R300_TX_ENABLE_8 (1 << 8) +# define R300_TX_ENABLE_9 (1 << 9) +# define R300_TX_ENABLE_10 (1 << 10) +# define R300_TX_ENABLE_11 (1 << 11) +# define R300_TX_ENABLE_12 (1 << 12) +# define R300_TX_ENABLE_13 (1 << 13) +# define R300_TX_ENABLE_14 (1 << 14) +# define R300_TX_ENABLE_15 (1 << 15) + +/* The pointsize is given in multiples of 6. The pointsize can be +// enormous: Clear() renders a single point that fills the entire +// framebuffer. */ +#define R300_RE_POINTSIZE 0x421C +# define R300_POINTSIZE_Y_SHIFT 0 +# define R300_POINTSIZE_Y_MASK (0xFFFF << 0) /* GUESS */ +# define R300_POINTSIZE_X_SHIFT 16 +# define R300_POINTSIZE_X_MASK (0xFFFF << 16) /* GUESS */ +# define R300_POINTSIZE_MAX (R300_POINTSIZE_Y_MASK / 6) + +/* The line width is given in multiples of 6. + In default mode lines are classified as vertical lines. + HO: horizontal + VE: vertical or horizontal + HO & VE: no classification +*/ +#define R300_RE_LINE_CNT 0x4234 +# define R300_LINESIZE_SHIFT 0 +# define R300_LINESIZE_MASK (0xFFFF << 0) /* GUESS */ +# define R300_LINESIZE_MAX (R300_LINESIZE_MASK / 6) +# define R300_LINE_CNT_HO (1 << 16) +# define R300_LINE_CNT_VE (1 << 17) + +/* Some sort of scale or clamp value for texcoordless textures. */ +#define R300_RE_UNK4238 0x4238 + +#define R300_RE_SHADE_MODEL 0x4278 +# define R300_RE_SHADE_MODEL_SMOOTH 0x3aaaa +# define R300_RE_SHADE_MODEL_FLAT 0x39595 + +/* Dangerous */ +#define R300_RE_POLYGON_MODE 0x4288 +# define R300_PM_ENABLED (1 << 0) +# define R300_PM_FRONT_POINT (0 << 0) +# define R300_PM_BACK_POINT (0 << 0) +# define R300_PM_FRONT_LINE (1 << 4) +# define R300_PM_FRONT_FILL (1 << 5) +# define R300_PM_BACK_LINE (1 << 7) +# define R300_PM_BACK_FILL (1 << 8) + +/* Not sure why there are duplicate of factor and constant values. + My best guess so far is that there are seperate zbiases for test and write. + Ordering might be wrong. + Some of the tests indicate that fgl has a fallback implementation of zbias + via pixel shaders. */ +#define R300_RE_ZBIAS_T_FACTOR 0x42A4 +#define R300_RE_ZBIAS_T_CONSTANT 0x42A8 +#define R300_RE_ZBIAS_W_FACTOR 0x42AC +#define R300_RE_ZBIAS_W_CONSTANT 0x42B0 + +/* This register needs to be set to (1<<1) for RV350 to correctly + perform depth test (see --vb-triangles in r300_demo) + Don't know about other chips. - Vladimir + This is set to 3 when GL_POLYGON_OFFSET_FILL is on. + My guess is that there are two bits for each zbias primitive (FILL, LINE, POINT). + One to enable depth test and one for depth write. + Yet this doesnt explain why depth writes work ... + */ +#define R300_RE_OCCLUSION_CNTL 0x42B4 +# define R300_OCCLUSION_ON (1<<1) + +#define R300_RE_CULL_CNTL 0x42B8 +# define R300_CULL_FRONT (1 << 0) +# define R300_CULL_BACK (1 << 1) +# define R300_FRONT_FACE_CCW (0 << 2) +# define R300_FRONT_FACE_CW (1 << 2) + + +/* BEGIN: Rasterization / Interpolators - many guesses +// 0_UNKNOWN_18 has always been set except for clear operations. +// TC_CNT is the number of incoming texture coordinate sets (i.e. it depends +// on the vertex program, *not* the fragment program) */ +#define R300_RS_CNTL_0 0x4300 +# define R300_RS_CNTL_TC_CNT_SHIFT 2 +# define R300_RS_CNTL_TC_CNT_MASK (7 << 2) +# define R300_RS_CNTL_CI_CNT_SHIFT 7 /* number of color interpolators used */ +# define R300_RS_CNTL_0_UNKNOWN_18 (1 << 18) +/* Guess: RS_CNTL_1 holds the index of the highest used RS_ROUTE_n register. */ +#define R300_RS_CNTL_1 0x4304 + +/* gap */ +/* Only used for texture coordinates. +// Use the source field to route texture coordinate input from the vertex program +// to the desired interpolator. Note that the source field is relative to the +// outputs the vertex program *actually* writes. If a vertex program only writes +// texcoord[1], this will be source index 0. +// Set INTERP_USED on all interpolators that produce data used by the +// fragment program. INTERP_USED looks like a swizzling mask, but +// I haven't seen it used that way. +// +// Note: The _UNKNOWN constants are always set in their respective register. +// I don't know if this is necessary. */ +#define R300_RS_INTERP_0 0x4310 +#define R300_RS_INTERP_1 0x4314 +# define R300_RS_INTERP_1_UNKNOWN 0x40 +#define R300_RS_INTERP_2 0x4318 +# define R300_RS_INTERP_2_UNKNOWN 0x80 +#define R300_RS_INTERP_3 0x431C +# define R300_RS_INTERP_3_UNKNOWN 0xC0 +#define R300_RS_INTERP_4 0x4320 +#define R300_RS_INTERP_5 0x4324 +#define R300_RS_INTERP_6 0x4328 +#define R300_RS_INTERP_7 0x432C +# define R300_RS_INTERP_SRC_SHIFT 2 +# define R300_RS_INTERP_SRC_MASK (7 << 2) +# define R300_RS_INTERP_USED 0x00D10000 + +/* These DWORDs control how vertex data is routed into fragment program +// registers, after interpolators. */ +#define R300_RS_ROUTE_0 0x4330 +#define R300_RS_ROUTE_1 0x4334 +#define R300_RS_ROUTE_2 0x4338 +#define R300_RS_ROUTE_3 0x433C /* GUESS */ +#define R300_RS_ROUTE_4 0x4340 /* GUESS */ +#define R300_RS_ROUTE_5 0x4344 /* GUESS */ +#define R300_RS_ROUTE_6 0x4348 /* GUESS */ +#define R300_RS_ROUTE_7 0x434C /* GUESS */ +# define R300_RS_ROUTE_SOURCE_INTERP_0 0 +# define R300_RS_ROUTE_SOURCE_INTERP_1 1 +# define R300_RS_ROUTE_SOURCE_INTERP_2 2 +# define R300_RS_ROUTE_SOURCE_INTERP_3 3 +# define R300_RS_ROUTE_SOURCE_INTERP_4 4 +# define R300_RS_ROUTE_SOURCE_INTERP_5 5 /* GUESS */ +# define R300_RS_ROUTE_SOURCE_INTERP_6 6 /* GUESS */ +# define R300_RS_ROUTE_SOURCE_INTERP_7 7 /* GUESS */ +# define R300_RS_ROUTE_ENABLE (1 << 3) /* GUESS */ +# define R300_RS_ROUTE_DEST_SHIFT 6 +# define R300_RS_ROUTE_DEST_MASK (31 << 6) /* GUESS */ + +/* Special handling for color: When the fragment program uses color, +// the ROUTE_0_COLOR bit is set and ROUTE_0_COLOR_DEST contains the +// color register index. */ +# define R300_RS_ROUTE_0_COLOR (1 << 14) +# define R300_RS_ROUTE_0_COLOR_DEST_SHIFT 17 +# define R300_RS_ROUTE_0_COLOR_DEST_MASK (31 << 17) /* GUESS */ +/* As above, but for secondary color */ +# define R300_RS_ROUTE_1_COLOR1 (1 << 14) +# define R300_RS_ROUTE_1_COLOR1_DEST_SHIFT 17 +# define R300_RS_ROUTE_1_COLOR1_DEST_MASK (31 << 17) +# define R300_RS_ROUTE_1_UNKNOWN11 (1 << 11) +/* END */ + +/* BEGIN: Scissors and cliprects +// There are four clipping rectangles. Their corner coordinates are inclusive. +// Every pixel is assigned a number from 0 and 15 by setting bits 0-3 depending +// on whether the pixel is inside cliprects 0-3, respectively. For example, +// if a pixel is inside cliprects 0 and 1, but outside 2 and 3, it is assigned +// the number 3 (binary 0011). +// Iff the bit corresponding to the pixel's number in RE_CLIPRECT_CNTL is set, +// the pixel is rasterized. +// +// In addition to this, there is a scissors rectangle. Only pixels inside the +// scissors rectangle are drawn. (coordinates are inclusive) +// +// For some reason, the top-left corner of the framebuffer is at (1440, 1440) +// for the purpose of clipping and scissors. */ +#define R300_RE_CLIPRECT_TL_0 0x43B0 +#define R300_RE_CLIPRECT_BR_0 0x43B4 +#define R300_RE_CLIPRECT_TL_1 0x43B8 +#define R300_RE_CLIPRECT_BR_1 0x43BC +#define R300_RE_CLIPRECT_TL_2 0x43C0 +#define R300_RE_CLIPRECT_BR_2 0x43C4 +#define R300_RE_CLIPRECT_TL_3 0x43C8 +#define R300_RE_CLIPRECT_BR_3 0x43CC +# define R300_CLIPRECT_OFFSET 1440 +# define R300_CLIPRECT_MASK 0x1FFF +# define R300_CLIPRECT_X_SHIFT 0 +# define R300_CLIPRECT_X_MASK (0x1FFF << 0) +# define R300_CLIPRECT_Y_SHIFT 13 +# define R300_CLIPRECT_Y_MASK (0x1FFF << 13) +#define R300_RE_CLIPRECT_CNTL 0x43D0 +# define R300_CLIP_OUT (1 << 0) +# define R300_CLIP_0 (1 << 1) +# define R300_CLIP_1 (1 << 2) +# define R300_CLIP_10 (1 << 3) +# define R300_CLIP_2 (1 << 4) +# define R300_CLIP_20 (1 << 5) +# define R300_CLIP_21 (1 << 6) +# define R300_CLIP_210 (1 << 7) +# define R300_CLIP_3 (1 << 8) +# define R300_CLIP_30 (1 << 9) +# define R300_CLIP_31 (1 << 10) +# define R300_CLIP_310 (1 << 11) +# define R300_CLIP_32 (1 << 12) +# define R300_CLIP_320 (1 << 13) +# define R300_CLIP_321 (1 << 14) +# define R300_CLIP_3210 (1 << 15) + +/* gap */ +#define R300_RE_SCISSORS_TL 0x43E0 +#define R300_RE_SCISSORS_BR 0x43E4 +# define R300_SCISSORS_OFFSET 1440 +# define R300_SCISSORS_X_SHIFT 0 +# define R300_SCISSORS_X_MASK (0x1FFF << 0) +# define R300_SCISSORS_Y_SHIFT 13 +# define R300_SCISSORS_Y_MASK (0x1FFF << 13) +/* END */ + +/* BEGIN: Texture specification +// The texture specification dwords are grouped by meaning and not by texture unit. +// This means that e.g. the offset for texture image unit N is found in register +// TX_OFFSET_0 + (4*N) */ +#define R300_TX_FILTER_0 0x4400 +# define R300_TX_REPEAT 0 +# define R300_TX_MIRRORED 1 +# define R300_TX_CLAMP 4 +# define R300_TX_CLAMP_TO_EDGE 2 +# define R300_TX_CLAMP_TO_BORDER 6 +# define R300_TX_WRAP_S_SHIFT 0 +# define R300_TX_WRAP_S_MASK (7 << 0) +# define R300_TX_WRAP_T_SHIFT 3 +# define R300_TX_WRAP_T_MASK (7 << 3) +# define R300_TX_WRAP_Q_SHIFT 6 +# define R300_TX_WRAP_Q_MASK (7 << 6) +# define R300_TX_MAG_FILTER_NEAREST (1 << 9) +# define R300_TX_MAG_FILTER_LINEAR (2 << 9) +# define R300_TX_MAG_FILTER_MASK (3 << 9) +# define R300_TX_MIN_FILTER_NEAREST (1 << 11) +# define R300_TX_MIN_FILTER_LINEAR (2 << 11) +# define R300_TX_MIN_FILTER_NEAREST_MIP_NEAREST (5 << 11) +# define R300_TX_MIN_FILTER_NEAREST_MIP_LINEAR (9 << 11) +# define R300_TX_MIN_FILTER_LINEAR_MIP_NEAREST (6 << 11) +# define R300_TX_MIN_FILTER_LINEAR_MIP_LINEAR (10 << 11) + +/* NOTE: NEAREST doesnt seem to exist. + Im not seting MAG_FILTER_MASK and (3 << 11) on for all + anisotropy modes because that would void selected mag filter */ +# define R300_TX_MIN_FILTER_ANISO_NEAREST ((0 << 13) /*|R300_TX_MAG_FILTER_MASK|(3<<11)*/) +# define R300_TX_MIN_FILTER_ANISO_LINEAR ((0 << 13) /*|R300_TX_MAG_FILTER_MASK|(3<<11)*/) +# define R300_TX_MIN_FILTER_ANISO_NEAREST_MIP_NEAREST ((1 << 13) /*|R300_TX_MAG_FILTER_MASK|(3<<11)*/) +# define R300_TX_MIN_FILTER_ANISO_NEAREST_MIP_LINEAR ((2 << 13) /*|R300_TX_MAG_FILTER_MASK|(3<<11)*/) +# define R300_TX_MIN_FILTER_MASK ( (15 << 11) | (3 << 13) ) +# define R300_TX_MAX_ANISO_1_TO_1 (0 << 21) +# define R300_TX_MAX_ANISO_2_TO_1 (2 << 21) +# define R300_TX_MAX_ANISO_4_TO_1 (4 << 21) +# define R300_TX_MAX_ANISO_8_TO_1 (6 << 21) +# define R300_TX_MAX_ANISO_16_TO_1 (8 << 21) +# define R300_TX_MAX_ANISO_MASK (14 << 21) + +#define R300_TX_UNK1_0 0x4440 +# define R300_LOD_BIAS_MASK 0x1fff + +#define R300_TX_SIZE_0 0x4480 +# define R300_TX_WIDTHMASK_SHIFT 0 +# define R300_TX_WIDTHMASK_MASK (2047 << 0) +# define R300_TX_HEIGHTMASK_SHIFT 11 +# define R300_TX_HEIGHTMASK_MASK (2047 << 11) +# define R300_TX_UNK23 (1 << 23) +# define R300_TX_SIZE_SHIFT 26 /* largest of width, height */ +# define R300_TX_SIZE_MASK (15 << 26) +#define R300_TX_FORMAT_0 0x44C0 + /* The interpretation of the format word by Wladimir van der Laan */ + /* The X, Y, Z and W refer to the layout of the components. + They are given meanings as R, G, B and Alpha by the swizzle + specification */ +# define R300_TX_FORMAT_X8 0x0 +# define R300_TX_FORMAT_X16 0x1 +# define R300_TX_FORMAT_Y4X4 0x2 +# define R300_TX_FORMAT_Y8X8 0x3 +# define R300_TX_FORMAT_Y16X16 0x4 +# define R300_TX_FORMAT_Z3Y3X2 0x5 +# define R300_TX_FORMAT_Z5Y6X5 0x6 +# define R300_TX_FORMAT_Z6Y5X5 0x7 +# define R300_TX_FORMAT_Z11Y11X10 0x8 +# define R300_TX_FORMAT_Z10Y11X11 0x9 +# define R300_TX_FORMAT_W4Z4Y4X4 0xA +# define R300_TX_FORMAT_W1Z5Y5X5 0xB +# define R300_TX_FORMAT_W8Z8Y8X8 0xC +# define R300_TX_FORMAT_W2Z10Y10X10 0xD +# define R300_TX_FORMAT_W16Z16Y16X16 0xE +# define R300_TX_FORMAT_DXT1 0xF +# define R300_TX_FORMAT_DXT3 0x10 +# define R300_TX_FORMAT_DXT5 0x11 +# define R300_TX_FORMAT_D3DMFT_CxV8U8 0x12 /* no swizzle */ +# define R300_TX_FORMAT_A8R8G8B8 0x13 /* no swizzle */ +# define R300_TX_FORMAT_B8G8_B8G8 0x14 /* no swizzle */ +# define R300_TX_FORMAT_G8R8_G8B8 0x15 /* no swizzle */ + /* 0x16 - some 16 bit green format.. ?? */ +# define R300_TX_FORMAT_UNK25 (1 << 25) /* no swizzle */ + + /* gap */ + /* Floating point formats */ + /* Note - hardware supports both 16 and 32 bit floating point */ +# define R300_TX_FORMAT_FL_I16 0x18 +# define R300_TX_FORMAT_FL_I16A16 0x19 +# define R300_TX_FORMAT_FL_R16G16B16A16 0x1A +# define R300_TX_FORMAT_FL_I32 0x1B +# define R300_TX_FORMAT_FL_I32A32 0x1C +# define R300_TX_FORMAT_FL_R32G32B32A32 0x1D + /* alpha modes, convenience mostly */ + /* if you have alpha, pick constant appropriate to the + number of channels (1 for I8, 2 for I8A8, 4 for R8G8B8A8, etc */ +# define R300_TX_FORMAT_ALPHA_1CH 0x000 +# define R300_TX_FORMAT_ALPHA_2CH 0x200 +# define R300_TX_FORMAT_ALPHA_4CH 0x600 +# define R300_TX_FORMAT_ALPHA_NONE 0xA00 + /* Swizzling */ + /* constants */ +# define R300_TX_FORMAT_X 0 +# define R300_TX_FORMAT_Y 1 +# define R300_TX_FORMAT_Z 2 +# define R300_TX_FORMAT_W 3 +# define R300_TX_FORMAT_ZERO 4 +# define R300_TX_FORMAT_ONE 5 +# define R300_TX_FORMAT_CUT_Z 6 /* 2.0*Z, everything above 1.0 is set to 0.0 */ +# define R300_TX_FORMAT_CUT_W 7 /* 2.0*W, everything above 1.0 is set to 0.0 */ + +# define R300_TX_FORMAT_B_SHIFT 18 +# define R300_TX_FORMAT_G_SHIFT 15 +# define R300_TX_FORMAT_R_SHIFT 12 +# define R300_TX_FORMAT_A_SHIFT 9 + /* Convenience macro to take care of layout and swizzling */ +# define R300_EASY_TX_FORMAT(B, G, R, A, FMT) (\ + ((R300_TX_FORMAT_##B)<is_pci ) { + /* set RADEON_AGP_BASE here instead of relying on X from user space */ + RADEON_WRITE(RADEON_AGP_BASE, (unsigned int)dev->agp->base); RADEON_WRITE( RADEON_CP_RB_RPTR_ADDR, dev_priv->ring_rptr->offset - dev->agp->base @@ -1626,6 +1629,9 @@ int radeon_cp_init( DRM_IOCTL_ARGS ) DRM_COPY_FROM_USER_IOCTL( init, (drm_radeon_init_t __user *)data, sizeof(init) ); + if(init.func == RADEON_INIT_R300_CP) + r300_init_reg_flags(); + switch ( init.func ) { case RADEON_INIT_CP: case RADEON_INIT_R200_CP: @@ -2040,12 +2046,19 @@ int radeon_driver_preinit(struct drm_device *dev, unsigned long flags) case CHIP_RV200: case CHIP_R200: case CHIP_R300: + case CHIP_R420: dev_priv->flags |= CHIP_HAS_HIERZ; break; default: /* all other chips have no hierarchical z buffer */ break; } + + if (drm_device_is_agp(dev)) + dev_priv->flags |= CHIP_IS_AGP; + + DRM_DEBUG("%s card detected\n", + ((dev_priv->flags & CHIP_IS_AGP) ? "AGP" : "PCI")); return ret; } diff --git a/drivers/char/drm/radeon_drm.h b/drivers/char/drm/radeon_drm.h index c1e62d047989..3792798270a4 100644 --- a/drivers/char/drm/radeon_drm.h +++ b/drivers/char/drm/radeon_drm.h @@ -195,6 +195,52 @@ typedef union { #define RADEON_WAIT_2D 0x1 #define RADEON_WAIT_3D 0x2 +/* Allowed parameters for R300_CMD_PACKET3 + */ +#define R300_CMD_PACKET3_CLEAR 0 +#define R300_CMD_PACKET3_RAW 1 + +/* Commands understood by cmd_buffer ioctl for R300. + * The interface has not been stabilized, so some of these may be removed + * and eventually reordered before stabilization. + */ +#define R300_CMD_PACKET0 1 +#define R300_CMD_VPU 2 /* emit vertex program upload */ +#define R300_CMD_PACKET3 3 /* emit a packet3 */ +#define R300_CMD_END3D 4 /* emit sequence ending 3d rendering */ +#define R300_CMD_CP_DELAY 5 +#define R300_CMD_DMA_DISCARD 6 +#define R300_CMD_WAIT 7 +# define R300_WAIT_2D 0x1 +# define R300_WAIT_3D 0x2 +# define R300_WAIT_2D_CLEAN 0x3 +# define R300_WAIT_3D_CLEAN 0x4 + +typedef union { + unsigned int u; + struct { + unsigned char cmd_type, pad0, pad1, pad2; + } header; + struct { + unsigned char cmd_type, count, reglo, reghi; + } packet0; + struct { + unsigned char cmd_type, count, adrlo, adrhi; + } vpu; + struct { + unsigned char cmd_type, packet, pad0, pad1; + } packet3; + struct { + unsigned char cmd_type, packet; + unsigned short count; /* amount of packet2 to emit */ + } delay; + struct { + unsigned char cmd_type, buf_idx, pad0, pad1; + } dma; + struct { + unsigned char cmd_type, flags, pad0, pad1; + } wait; +} drm_r300_cmd_header_t; #define RADEON_FRONT 0x1 #define RADEON_BACK 0x2 diff --git a/drivers/char/drm/radeon_drv.h b/drivers/char/drm/radeon_drv.h index e701dffe978d..f12a963ede18 100644 --- a/drivers/char/drm/radeon_drv.h +++ b/drivers/char/drm/radeon_drv.h @@ -82,9 +82,10 @@ * - Add support for r100 cube maps * 1.16- Add R200_EMIT_PP_TRI_PERF_CNTL packet to support brilinear * texture filtering on r200 + * 1.17- Add initial support for R300 (3D). */ #define DRIVER_MAJOR 1 -#define DRIVER_MINOR 16 +#define DRIVER_MINOR 17 #define DRIVER_PATCHLEVEL 0 #define GET_RING_HEAD(dev_priv) DRM_READ32( (dev_priv)->ring_rptr, 0 ) @@ -106,7 +107,9 @@ enum radeon_family { CHIP_RV280, CHIP_R300, CHIP_RS300, + CHIP_R350, CHIP_RV350, + CHIP_R420, CHIP_LAST, }; @@ -321,6 +324,14 @@ extern int radeon_postcleanup( struct drm_device *dev ); extern long radeon_compat_ioctl(struct file *filp, unsigned int cmd, unsigned long arg); + +/* r300_cmdbuf.c */ +extern void r300_init_reg_flags(void); + +extern int r300_do_cp_cmdbuf(drm_device_t* dev, DRMFILE filp, + drm_file_t* filp_priv, + drm_radeon_cmd_buffer_t* cmdbuf); + /* Flags for stats.boxes */ #define RADEON_BOX_DMA_IDLE 0x1 @@ -358,6 +369,11 @@ extern long radeon_compat_ioctl(struct file *filp, unsigned int cmd, #define RADEON_CRTC2_OFFSET 0x0324 #define RADEON_CRTC2_OFFSET_CNTL 0x0328 +#define RADEON_MPP_TB_CONFIG 0x01c0 +#define RADEON_MEM_CNTL 0x0140 +#define RADEON_MEM_SDRAM_MODE_REG 0x0158 +#define RADEON_AGP_BASE 0x0170 + #define RADEON_RB3D_COLOROFFSET 0x1c40 #define RADEON_RB3D_COLORPITCH 0x1c48 @@ -652,16 +668,27 @@ extern long radeon_compat_ioctl(struct file *filp, unsigned int cmd, #define RADEON_CP_PACKET1 0x40000000 #define RADEON_CP_PACKET2 0x80000000 #define RADEON_CP_PACKET3 0xC0000000 +# define RADEON_CP_NOP 0x00001000 +# define RADEON_CP_NEXT_CHAR 0x00001900 +# define RADEON_CP_PLY_NEXTSCAN 0x00001D00 +# define RADEON_CP_SET_SCISSORS 0x00001E00 + /* GEN_INDX_PRIM is unsupported starting with R300 */ # define RADEON_3D_RNDR_GEN_INDX_PRIM 0x00002300 # define RADEON_WAIT_FOR_IDLE 0x00002600 # define RADEON_3D_DRAW_VBUF 0x00002800 # define RADEON_3D_DRAW_IMMD 0x00002900 # define RADEON_3D_DRAW_INDX 0x00002A00 +# define RADEON_CP_LOAD_PALETTE 0x00002C00 # define RADEON_3D_LOAD_VBPNTR 0x00002F00 # define RADEON_MPEG_IDCT_MACROBLOCK 0x00003000 # define RADEON_MPEG_IDCT_MACROBLOCK_REV 0x00003100 # define RADEON_3D_CLEAR_ZMASK 0x00003200 +# define RADEON_CP_INDX_BUFFER 0x00003300 +# define RADEON_CP_3D_DRAW_VBUF_2 0x00003400 +# define RADEON_CP_3D_DRAW_IMMD_2 0x00003500 +# define RADEON_CP_3D_DRAW_INDX_2 0x00003600 # define RADEON_3D_CLEAR_HIZ 0x00003700 +# define RADEON_CP_3D_CLEAR_CMASK 0x00003802 # define RADEON_CNTL_HOSTDATA_BLT 0x00009400 # define RADEON_CNTL_PAINT_MULTI 0x00009A00 # define RADEON_CNTL_BITBLT_MULTI 0x00009B00 diff --git a/drivers/char/drm/radeon_state.c b/drivers/char/drm/radeon_state.c index 1f79e249146c..d57accdd8df5 100644 --- a/drivers/char/drm/radeon_state.c +++ b/drivers/char/drm/radeon_state.c @@ -2797,6 +2797,17 @@ static int radeon_cp_cmdbuf( DRM_IOCTL_ARGS ) orig_nbox = cmdbuf.nbox; + if(dev_priv->microcode_version == UCODE_R300) { + int temp; + temp=r300_do_cp_cmdbuf(dev, filp, filp_priv, &cmdbuf); + + if (orig_bufsz != 0) + drm_free(kbuf, orig_bufsz, DRM_MEM_DRIVER); + + return temp; + } + + /* microcode_version != r300 */ while ( cmdbuf.bufsz >= sizeof(header) ) { header.i = *(int *)cmdbuf.buf; -- 2.20.1