From 3faa1ffb4f4be7d10715f4b003ff7b27d14eae26 Mon Sep 17 00:00:00 2001 From: Hans de Goede Date: Sun, 17 Jun 2007 00:28:45 +0200 Subject: [PATCH] hwmon: Add support for newer uGuru's This patch adds a new driver for the hardware monitoring features of the third revision of the Abit uGuru chip, found on recent Abit motherboards. This is an entirely different beast then the first and second revision (its again a winbond microcontroller, but the "protocol" to talk to it and the bank addresses are very different. Signed-off-by: Hans de Goede Signed-off-by: Mark M. Hoffman --- Documentation/hwmon/abituguru | 31 +- Documentation/hwmon/abituguru3 | 65 ++ drivers/hwmon/Kconfig | 27 +- drivers/hwmon/Makefile | 1 + drivers/hwmon/abituguru.c | 6 +- drivers/hwmon/abituguru3.c | 1139 ++++++++++++++++++++++++++++++++ 6 files changed, 1248 insertions(+), 21 deletions(-) create mode 100644 Documentation/hwmon/abituguru3 create mode 100644 drivers/hwmon/abituguru3.c diff --git a/Documentation/hwmon/abituguru b/Documentation/hwmon/abituguru index b2c0d61b39a2..87ffa0f5ec70 100644 --- a/Documentation/hwmon/abituguru +++ b/Documentation/hwmon/abituguru @@ -2,7 +2,7 @@ Kernel driver abituguru ======================= Supported chips: - * Abit uGuru revision 1-3 (Hardware Monitor part only) + * Abit uGuru revision 1 & 2 (Hardware Monitor part only) Prefix: 'abituguru' Addresses scanned: ISA 0x0E0 Datasheet: Not available, this driver is based on reverse engineering. @@ -20,8 +20,8 @@ Supported chips: uGuru 2.1.0.0 ~ 2.1.2.8 (AS8, AV8, AA8, AG8, AA8XE, AX8) uGuru 2.2.0.0 ~ 2.2.0.6 (AA8 Fatal1ty) uGuru 2.3.0.0 ~ 2.3.0.9 (AN8) - uGuru 3.0.0.0 ~ 3.0.1.2 (AW8, AL8, NI8) - uGuru 4.xxxxx? (AT8 32X) (2) + uGuru 3.0.0.0 ~ 3.0.x.x (AW8, AL8, AT8, NI8 SLI, AT8 32X, AN8 32X, + AW9D-MAX) (2) 1) For revisions 2 and 3 uGuru's the driver can autodetect the sensortype (Volt or Temp) for bank1 sensors, for revision 1 uGuru's this doesnot always work. For these uGuru's the autodection can @@ -30,8 +30,9 @@ Supported chips: bank1_types=1,1,0,0,0,0,0,2,0,0,0,0,2,0,0,1 You may also need to specify the fan_sensors option for these boards fan_sensors=5 - 2) The current version of the abituguru driver is known to NOT work - on these Motherboards + 2) There is a seperate abituguru3 driver for these motherboards, + the abituguru (without the 3 !) driver will not work on these + motherboards (and visa versa)! Authors: Hans de Goede , @@ -43,8 +44,10 @@ Module Parameters ----------------- * force: bool Force detection. Note this parameter only causes the - detection to be skipped, if the uGuru can't be read - the module initialization (insmod) will still fail. + detection to be skipped, and thus the insmod to + succeed. If the uGuru can't be read the actual hwmon + driver will not load and thus no hwmon device will get + registered. * bank1_types: int[] Bank1 sensortype autodetection override: -1 autodetect (default) 0 volt sensor @@ -69,13 +72,15 @@ dmesg | grep abituguru Description ----------- -This driver supports the hardware monitoring features of the Abit uGuru chip -found on Abit uGuru featuring motherboards (most modern Abit motherboards). +This driver supports the hardware monitoring features of the first and +second revision of the Abit uGuru chip found on Abit uGuru featuring +motherboards (most modern Abit motherboards). -The uGuru chip in reality is a Winbond W83L950D in disguise (despite Abit -claiming it is "a new microprocessor designed by the ABIT Engineers"). -Unfortunatly this doesn't help since the W83L950D is a generic -microcontroller with a custom Abit application running on it. +The first and second revision of the uGuru chip in reality is a Winbond +W83L950D in disguise (despite Abit claiming it is "a new microprocessor +designed by the ABIT Engineers"). Unfortunatly this doesn't help since the +W83L950D is a generic microcontroller with a custom Abit application running +on it. Despite Abit not releasing any information regarding the uGuru, Olle Sandberg has managed to reverse engineer the sensor part diff --git a/Documentation/hwmon/abituguru3 b/Documentation/hwmon/abituguru3 new file mode 100644 index 000000000000..fa598aac22fa --- /dev/null +++ b/Documentation/hwmon/abituguru3 @@ -0,0 +1,65 @@ +Kernel driver abituguru3 +======================== + +Supported chips: + * Abit uGuru revision 3 (Hardware Monitor part, reading only) + Prefix: 'abituguru3' + Addresses scanned: ISA 0x0E0 + Datasheet: Not available, this driver is based on reverse engineering. + Note: + The uGuru is a microcontroller with onboard firmware which programs + it to behave as a hwmon IC. There are many different revisions of the + firmware and thus effectivly many different revisions of the uGuru. + Below is an incomplete list with which revisions are used for which + Motherboards: + uGuru 1.00 ~ 1.24 (AI7, KV8-MAX3, AN7) + uGuru 2.0.0.0 ~ 2.0.4.2 (KV8-PRO) + uGuru 2.1.0.0 ~ 2.1.2.8 (AS8, AV8, AA8, AG8, AA8XE, AX8) + uGuru 2.3.0.0 ~ 2.3.0.9 (AN8) + uGuru 3.0.0.0 ~ 3.0.x.x (AW8, AL8, AT8, NI8 SLI, AT8 32X, AN8 32X, + AW9D-MAX) + The abituguru3 driver is only for revison 3.0.x.x motherboards, + this driver will not work on older motherboards. For older + motherboards use the abituguru (without the 3 !) driver. + +Authors: + Hans de Goede , + (Initial reverse engineering done by Louis Kruger) + + +Module Parameters +----------------- + +* force: bool Force detection. Note this parameter only causes the + detection to be skipped, and thus the insmod to + succeed. If the uGuru can't be read the actual hwmon + driver will not load and thus no hwmon device will get + registered. +* verbose: bool Should the driver be verbose? + 0/off/false normal output + 1/on/true + verbose error reporting (default) + Default: 1 (the driver is still in the testing phase) + +Description +----------- + +This driver supports the hardware monitoring features of the third revision of +the Abit uGuru chip, found on recent Abit uGuru featuring motherboards. + +The 3rd revision of the uGuru chip in reality is a Winbond W83L951G. +Unfortunatly this doesn't help since the W83L951G is a generic microcontroller +with a custom Abit application running on it. + +Despite Abit not releasing any information regarding the uGuru revision 3, +Louis Kruger has managed to reverse engineer the sensor part of the uGuru. +Without his work this driver would not have been possible. + +Known Issues +------------ + +The voltage and frequency control parts of the Abit uGuru are not supported, +neither is writing any of the sensor settings and writing / reading the +fanspeed control registers (FanEQ) + +If you encounter any problems please mail me and +include the output of: "dmesg | grep abituguru" diff --git a/drivers/hwmon/Kconfig b/drivers/hwmon/Kconfig index 9f01edeccac7..455a611c33e6 100644 --- a/drivers/hwmon/Kconfig +++ b/drivers/hwmon/Kconfig @@ -29,17 +29,34 @@ config HWMON_VID default n config SENSORS_ABITUGURU - tristate "Abit uGuru" + tristate "Abit uGuru (rev 1 & 2)" depends on EXPERIMENTAL help - If you say yes here you get support for the Abit uGuru chips - sensor part. The voltage and frequency control parts of the Abit - uGuru are not supported. The Abit uGuru chip can be found on Abit - uGuru featuring motherboards (most modern Abit motherboards). + If you say yes here you get support for the sensor part of the first + and second revision of the Abit uGuru chip. The voltage and frequency + control parts of the Abit uGuru are not supported. The Abit uGuru + chip can be found on Abit uGuru featuring motherboards (most modern + Abit motherboards from before end 2005). For more info and a list + of which motherboards have which revision see + Documentation/hwmon/abituguru This driver can also be built as a module. If so, the module will be called abituguru. +config SENSORS_ABITUGURU3 + tristate "Abit uGuru (rev 3)" + depends on HWMON && EXPERIMENTAL + help + If you say yes here you get support for the sensor part of the + third revision of the Abit uGuru chip. Only reading the sensors + and their settings is supported. The third revision of the Abit + uGuru chip can be found on recent Abit motherboards (since end + 2005). For more info and a list of which motherboards have which + revision see Documentation/hwmon/abituguru3 + + This driver can also be built as a module. If so, the module + will be called abituguru3. + config SENSORS_AD7418 tristate "Analog Devices AD7416, AD7417 and AD7418" depends on I2C && EXPERIMENTAL diff --git a/drivers/hwmon/Makefile b/drivers/hwmon/Makefile index 3618773bf4d6..763a53b17672 100644 --- a/drivers/hwmon/Makefile +++ b/drivers/hwmon/Makefile @@ -14,6 +14,7 @@ obj-$(CONFIG_SENSORS_W83781D) += w83781d.o obj-$(CONFIG_SENSORS_W83791D) += w83791d.o obj-$(CONFIG_SENSORS_ABITUGURU) += abituguru.o +obj-$(CONFIG_SENSORS_ABITUGURU3)+= abituguru3.o obj-$(CONFIG_SENSORS_AD7418) += ad7418.o obj-$(CONFIG_SENSORS_ADM1021) += adm1021.o obj-$(CONFIG_SENSORS_ADM1025) += adm1025.o diff --git a/drivers/hwmon/abituguru.c b/drivers/hwmon/abituguru.c index 0770688f79b6..c6186672405a 100644 --- a/drivers/hwmon/abituguru.c +++ b/drivers/hwmon/abituguru.c @@ -16,9 +16,9 @@ Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA. */ /* - This driver supports the sensor part of the custom Abit uGuru chip found - on Abit uGuru motherboards. Note: because of lack of specs the CPU / RAM / - etc voltage & frequency control is not supported! + This driver supports the sensor part of the first and second revision of + the custom Abit uGuru chip found on Abit uGuru motherboards. Note: because + of lack of specs the CPU/RAM voltage & frequency control is not supported! */ #include #include diff --git a/drivers/hwmon/abituguru3.c b/drivers/hwmon/abituguru3.c new file mode 100644 index 000000000000..cf6ac4cdff9a --- /dev/null +++ b/drivers/hwmon/abituguru3.c @@ -0,0 +1,1139 @@ +/* + abituguru3.c Copyright (c) 2006 Hans de Goede + + This program is free software; you can redistribute it and/or modify + it under the terms of the GNU General Public License as published by + the Free Software Foundation; either version 2 of the License, or + (at your option) any later version. + + This program is distributed in the hope that it will be useful, + but WITHOUT ANY WARRANTY; without even the implied warranty of + MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + GNU General Public License for more details. + + You should have received a copy of the GNU General Public License + along with this program; if not, write to the Free Software + Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA. +*/ +/* + This driver supports the sensor part of revision 3 of the custom Abit uGuru + chip found on newer Abit uGuru motherboards. Note: because of lack of specs + only reading the sensors and their settings is supported. +*/ +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include + +/* uGuru3 bank addresses */ +#define ABIT_UGURU3_SETTINGS_BANK 0x01 +#define ABIT_UGURU3_SENSORS_BANK 0x08 +#define ABIT_UGURU3_MISC_BANK 0x09 +#define ABIT_UGURU3_ALARMS_START 0x1E +#define ABIT_UGURU3_SETTINGS_START 0x24 +#define ABIT_UGURU3_VALUES_START 0x80 +#define ABIT_UGURU3_BOARD_ID 0x0A +/* uGuru3 sensor bank flags */ /* Alarm if: */ +#define ABIT_UGURU3_TEMP_HIGH_ALARM_ENABLE 0x01 /* temp over warn */ +#define ABIT_UGURU3_VOLT_HIGH_ALARM_ENABLE 0x02 /* volt over max */ +#define ABIT_UGURU3_VOLT_LOW_ALARM_ENABLE 0x04 /* volt under min */ +#define ABIT_UGURU3_TEMP_HIGH_ALARM_FLAG 0x10 /* temp is over warn */ +#define ABIT_UGURU3_VOLT_HIGH_ALARM_FLAG 0x20 /* volt is over max */ +#define ABIT_UGURU3_VOLT_LOW_ALARM_FLAG 0x40 /* volt is under min */ +#define ABIT_UGURU3_FAN_LOW_ALARM_ENABLE 0x01 /* fan under min */ +#define ABIT_UGURU3_BEEP_ENABLE 0x08 /* beep if alarm */ +#define ABIT_UGURU3_SHUTDOWN_ENABLE 0x80 /* shutdown if alarm */ +/* sensor types */ +#define ABIT_UGURU3_IN_SENSOR 0 +#define ABIT_UGURU3_TEMP_SENSOR 1 +#define ABIT_UGURU3_FAN_SENSOR 2 + +/* Timeouts / Retries, if these turn out to need a lot of fiddling we could + convert them to params. Determined by trial and error. I assume this is + cpu-speed independent, since the ISA-bus and not the CPU should be the + bottleneck. */ +#define ABIT_UGURU3_WAIT_TIMEOUT 250 +/* Normally the 0xAC at the end of synchronize() is reported after the + first read, but sometimes not and we need to poll */ +#define ABIT_UGURU3_SYNCHRONIZE_TIMEOUT 5 +/* utility macros */ +#define ABIT_UGURU3_NAME "abituguru3" +#define ABIT_UGURU3_DEBUG(format, arg...) \ + if (verbose) \ + printk(KERN_DEBUG ABIT_UGURU3_NAME ": " format , ## arg) + +/* Macros to help calculate the sysfs_names array length */ +#define ABIT_UGURU3_MAX_NO_SENSORS 26 +/* sum of strlen +1 of: in??_input\0, in??_{min,max}\0, in??_{min,max}_alarm\0, + in??_{min,max}_alarm_enable\0, in??_beep\0, in??_shutdown\0, in??_label\0 */ +#define ABIT_UGURU3_IN_NAMES_LENGTH (11 + 2 * 9 + 2 * 15 + 2 * 22 + 10 + 14 + 11) +/* sum of strlen +1 of: temp??_input\0, temp??_max\0, temp??_crit\0, + temp??_alarm\0, temp??_alarm_enable\0, temp??_beep\0, temp??_shutdown\0, + temp??_label\0 */ +#define ABIT_UGURU3_TEMP_NAMES_LENGTH (13 + 11 + 12 + 13 + 20 + 12 + 16 + 13) +/* sum of strlen +1 of: fan??_input\0, fan??_min\0, fan??_alarm\0, + fan??_alarm_enable\0, fan??_beep\0, fan??_shutdown\0, fan??_label\0 */ +#define ABIT_UGURU3_FAN_NAMES_LENGTH (12 + 10 + 12 + 19 + 11 + 15 + 12) +/* Worst case scenario 16 in sensors (longest names_length) and the rest + temp sensors (second longest names_length). */ +#define ABIT_UGURU3_SYSFS_NAMES_LENGTH (16 * ABIT_UGURU3_IN_NAMES_LENGTH + \ + (ABIT_UGURU3_MAX_NO_SENSORS - 16) * ABIT_UGURU3_TEMP_NAMES_LENGTH) + +/* All the macros below are named identical to the openguru2 program + reverse engineered by Louis Kruger, hence the names might not be 100% + logical. I could come up with better names, but I prefer keeping the names + identical so that this driver can be compared with his work more easily. */ +/* Two i/o-ports are used by uGuru */ +#define ABIT_UGURU3_BASE 0x00E0 +#define ABIT_UGURU3_CMD 0x00 +#define ABIT_UGURU3_DATA 0x04 +#define ABIT_UGURU3_REGION_LENGTH 5 +/* The wait_xxx functions return this on success and the last contents + of the DATA register (0-255) on failure. */ +#define ABIT_UGURU3_SUCCESS -1 +/* uGuru status flags */ +#define ABIT_UGURU3_STATUS_READY_FOR_READ 0x01 +#define ABIT_UGURU3_STATUS_BUSY 0x02 + + +/* Structures */ +struct abituguru3_sensor_info { + const char* name; + int port; + int type; + int multiplier; + int divisor; + int offset; +}; + +struct abituguru3_motherboard_info { + u16 id; + const char *name; + /* + 1 -> end of sensors indicated by a sensor with name == NULL */ + struct abituguru3_sensor_info sensors[ABIT_UGURU3_MAX_NO_SENSORS + 1]; +}; + +/* For the Abit uGuru, we need to keep some data in memory. + The structure is dynamically allocated, at the same time when a new + abituguru3 device is allocated. */ +struct abituguru3_data { + struct class_device *class_dev; /* hwmon registered device */ + struct mutex update_lock; /* protect access to data and uGuru */ + unsigned short addr; /* uguru base address */ + char valid; /* !=0 if following fields are valid */ + unsigned long last_updated; /* In jiffies */ + + /* For convenience the sysfs attr and their names are generated + automatically. We have max 10 entries per sensor (for in sensors) */ + struct sensor_device_attribute_2 sysfs_attr[ABIT_UGURU3_MAX_NO_SENSORS + * 10]; + + /* Buffer to store the dynamically generated sysfs names */ + char sysfs_names[ABIT_UGURU3_SYSFS_NAMES_LENGTH]; + + /* Pointer to the sensors info for the detected motherboard */ + const struct abituguru3_sensor_info *sensors; + + /* The abituguru3 supports upto 48 sensors, and thus has registers + sets for 48 sensors, for convienence reasons / simplicity of the + code we always read and store all registers for all 48 sensors */ + + /* Alarms for all 48 sensors (1 bit per sensor) */ + u8 alarms[48/8]; + + /* Value of all 48 sensors */ + u8 value[48]; + + /* Settings of all 48 sensors, note in and temp sensors (the first 32 + sensors) have 3 bytes of settings, while fans only have 2 bytes, + for convenience we use 3 bytes for all sensors */ + u8 settings[48][3]; +}; + + +/* Constants */ +static const struct abituguru3_motherboard_info abituguru3_motherboards[] = { + { 0x000C, "unknown", { + { "CPU Core", 0, 0, 10, 1, 0 }, + { "DDR", 1, 0, 10, 1, 0 }, + { "DDR VTT", 2, 0, 10, 1, 0 }, + { "CPU VTT 1.2V", 3, 0, 10, 1, 0 }, + { "MCH & PCIE 1.5V", 4, 0, 10, 1, 0 }, + { "MCH 2.5V", 5, 0, 20, 1, 0 }, + { "ICH 1.05V", 6, 0, 10, 1, 0 }, + { "ATX +12V (24-Pin)", 7, 0, 60, 1, 0 }, + { "ATX +12V (4-pin)", 8, 0, 60, 1, 0 }, + { "ATX +5V", 9, 0, 30, 1, 0 }, + { "+3.3V", 10, 0, 20, 1, 0 }, + { "5VSB", 11, 0, 30, 1, 0 }, + { "CPU", 24, 1, 1, 1, 0 }, + { "System ", 25, 1, 1, 1, 0 }, + { "PWM", 26, 1, 1, 1, 0 }, + { "CPU Fan", 32, 2, 60, 1, 0 }, + { "NB Fan", 33, 2, 60, 1, 0 }, + { "SYS FAN", 34, 2, 60, 1, 0 }, + { "AUX1 Fan", 35, 2, 60, 1, 0 }, + { NULL, 0, 0, 0, 0, 0 } } + }, + { 0x000D, "Abit AW8", { + { "CPU Core", 0, 0, 10, 1, 0 }, + { "DDR", 1, 0, 10, 1, 0 }, + { "DDR VTT", 2, 0, 10, 1, 0 }, + { "CPU VTT 1.2V", 3, 0, 10, 1, 0 }, + { "MCH & PCIE 1.5V", 4, 0, 10, 1, 0 }, + { "MCH 2.5V", 5, 0, 20, 1, 0 }, + { "ICH 1.05V", 6, 0, 10, 1, 0 }, + { "ATX +12V (24-Pin)", 7, 0, 60, 1, 0 }, + { "ATX +12V (4-pin)", 8, 0, 60, 1, 0 }, + { "ATX +5V", 9, 0, 30, 1, 0 }, + { "+3.3V", 10, 0, 20, 1, 0 }, + { "5VSB", 11, 0, 30, 1, 0 }, + { "CPU", 24, 1, 1, 1, 0 }, + { "System ", 25, 1, 1, 1, 0 }, + { "PWM1", 26, 1, 1, 1, 0 }, + { "PWM2", 27, 1, 1, 1, 0 }, + { "PWM3", 28, 1, 1, 1, 0 }, + { "PWM4", 29, 1, 1, 1, 0 }, + { "CPU Fan", 32, 2, 60, 1, 0 }, + { "NB Fan", 33, 2, 60, 1, 0 }, + { "SYS Fan", 34, 2, 60, 1, 0 }, + { "AUX1 Fan", 35, 2, 60, 1, 0 }, + { "AUX2 Fan", 36, 2, 60, 1, 0 }, + { "AUX3 Fan", 37, 2, 60, 1, 0 }, + { "AUX4 Fan", 38, 2, 60, 1, 0 }, + { "AUX5 Fan", 39, 2, 60, 1, 0 }, + { NULL, 0, 0, 0, 0, 0 } } + }, + { 0x000E, "AL-8", { + { "CPU Core", 0, 0, 10, 1, 0 }, + { "DDR", 1, 0, 10, 1, 0 }, + { "DDR VTT", 2, 0, 10, 1, 0 }, + { "CPU VTT 1.2V", 3, 0, 10, 1, 0 }, + { "MCH & PCIE 1.5V", 4, 0, 10, 1, 0 }, + { "MCH 2.5V", 5, 0, 20, 1, 0 }, + { "ICH 1.05V", 6, 0, 10, 1, 0 }, + { "ATX +12V (24-Pin)", 7, 0, 60, 1, 0 }, + { "ATX +12V (4-pin)", 8, 0, 60, 1, 0 }, + { "ATX +5V", 9, 0, 30, 1, 0 }, + { "+3.3V", 10, 0, 20, 1, 0 }, + { "5VSB", 11, 0, 30, 1, 0 }, + { "CPU", 24, 1, 1, 1, 0 }, + { "System ", 25, 1, 1, 1, 0 }, + { "PWM", 26, 1, 1, 1, 0 }, + { "CPU Fan", 32, 2, 60, 1, 0 }, + { "NB Fan", 33, 2, 60, 1, 0 }, + { "SYS Fan", 34, 2, 60, 1, 0 }, + { NULL, 0, 0, 0, 0, 0 } } + }, + { 0x000F, "unknown", { + { "CPU Core", 0, 0, 10, 1, 0 }, + { "DDR", 1, 0, 10, 1, 0 }, + { "DDR VTT", 2, 0, 10, 1, 0 }, + { "CPU VTT 1.2V", 3, 0, 10, 1, 0 }, + { "MCH & PCIE 1.5V", 4, 0, 10, 1, 0 }, + { "MCH 2.5V", 5, 0, 20, 1, 0 }, + { "ICH 1.05V", 6, 0, 10, 1, 0 }, + { "ATX +12V (24-Pin)", 7, 0, 60, 1, 0 }, + { "ATX +12V (4-pin)", 8, 0, 60, 1, 0 }, + { "ATX +5V", 9, 0, 30, 1, 0 }, + { "+3.3V", 10, 0, 20, 1, 0 }, + { "5VSB", 11, 0, 30, 1, 0 }, + { "CPU", 24, 1, 1, 1, 0 }, + { "System ", 25, 1, 1, 1, 0 }, + { "PWM", 26, 1, 1, 1, 0 }, + { "CPU Fan", 32, 2, 60, 1, 0 }, + { "NB Fan", 33, 2, 60, 1, 0 }, + { "SYS Fan", 34, 2, 60, 1, 0 }, + { NULL, 0, 0, 0, 0, 0 } } + }, + { 0x0010, "Abit NI8 SLI GR", { + { "CPU Core", 0, 0, 10, 1, 0 }, + { "DDR", 1, 0, 10, 1, 0 }, + { "DDR VTT", 2, 0, 10, 1, 0 }, + { "CPU VTT 1.2V", 3, 0, 10, 1, 0 }, + { "NB 1.4V", 4, 0, 10, 1, 0 }, + { "SB 1.5V", 6, 0, 10, 1, 0 }, + { "ATX +12V (24-Pin)", 7, 0, 60, 1, 0 }, + { "ATX +12V (4-pin)", 8, 0, 60, 1, 0 }, + { "ATX +5V", 9, 0, 30, 1, 0 }, + { "+3.3V", 10, 0, 20, 1, 0 }, + { "5VSB", 11, 0, 30, 1, 0 }, + { "CPU", 24, 1, 1, 1, 0 }, + { "SYS", 25, 1, 1, 1, 0 }, + { "PWM", 26, 1, 1, 1, 0 }, + { "CPU Fan", 32, 2, 60, 1, 0 }, + { "NB Fan", 33, 2, 60, 1, 0 }, + { "SYS Fan", 34, 2, 60, 1, 0 }, + { "AUX1 Fan", 35, 2, 60, 1, 0 }, + { "OTES1 Fan", 36, 2, 60, 1, 0 }, + { NULL, 0, 0, 0, 0, 0 } } + }, + { 0x0011, "Abit AT8 32X", { + { "CPU Core", 0, 0, 10, 1, 0 }, + { "DDR", 1, 0, 20, 1, 0 }, + { "DDR VTT", 2, 0, 10, 1, 0 }, + { "CPU VDDA 2.5V", 6, 0, 20, 1, 0 }, + { "NB 1.8V", 4, 0, 10, 1, 0 }, + { "NB 1.8V Dual", 5, 0, 10, 1, 0 }, + { "HTV 1.2", 3, 0, 10, 1, 0 }, + { "PCIE 1.2V", 12, 0, 10, 1, 0 }, + { "NB 1.2V", 13, 0, 10, 1, 0 }, + { "ATX +12V (24-Pin)", 7, 0, 60, 1, 0 }, + { "ATX +12V (4-pin)", 8, 0, 60, 1, 0 }, + { "ATX +5V", 9, 0, 30, 1, 0 }, + { "+3.3V", 10, 0, 20, 1, 0 }, + { "5VSB", 11, 0, 30, 1, 0 }, + { "CPU", 24, 1, 1, 1, 0 }, + { "NB", 25, 1, 1, 1, 0 }, + { "System", 26, 1, 1, 1, 0 }, + { "PWM", 27, 1, 1, 1, 0 }, + { "CPU Fan", 32, 2, 60, 1, 0 }, + { "NB Fan", 33, 2, 60, 1, 0 }, + { "SYS Fan", 34, 2, 60, 1, 0 }, + { "AUX1 Fan", 35, 2, 60, 1, 0 }, + { "AUX2 Fan", 36, 2, 60, 1, 0 }, + { NULL, 0, 0, 0, 0, 0 } } + }, + { 0x0012, "Abit AN8 32X", { + { "CPU Core", 0, 0, 10, 1, 0 }, + { "DDR", 1, 0, 20, 1, 0 }, + { "DDR VTT", 2, 0, 10, 1, 0 }, + { "HyperTransport", 3, 0, 10, 1, 0 }, + { "CPU VDDA 2.5V", 5, 0, 20, 1, 0 }, + { "NB", 4, 0, 10, 1, 0 }, + { "SB", 6, 0, 10, 1, 0 }, + { "ATX +12V (24-Pin)", 7, 0, 60, 1, 0 }, + { "ATX +12V (4-pin)", 8, 0, 60, 1, 0 }, + { "ATX +5V", 9, 0, 30, 1, 0 }, + { "+3.3V", 10, 0, 20, 1, 0 }, + { "5VSB", 11, 0, 30, 1, 0 }, + { "CPU", 24, 1, 1, 1, 0 }, + { "SYS", 25, 1, 1, 1, 0 }, + { "PWM", 26, 1, 1, 1, 0 }, + { "CPU Fan", 32, 2, 60, 1, 0 }, + { "NB Fan", 33, 2, 60, 1, 0 }, + { "SYS Fan", 34, 2, 60, 1, 0 }, + { "AUX1 Fan", 36, 2, 60, 1, 0 }, + { NULL, 0, 0, 0, 0, 0 } } + }, + { 0x0013, "unknown", { + { "CPU Core", 0, 0, 10, 1, 0 }, + { "DDR", 1, 0, 10, 1, 0 }, + { "DDR VTT", 2, 0, 10, 1, 0 }, + { "CPU VTT 1.2V", 3, 0, 10, 1, 0 }, + { "MCH & PCIE 1.5V", 4, 0, 10, 1, 0 }, + { "MCH 2.5V", 5, 0, 20, 1, 0 }, + { "ICH 1.05V", 6, 0, 10, 1, 0 }, + { "ATX +12V (24-Pin)", 7, 0, 60, 1, 0 }, + { "ATX +12V (4-pin)", 8, 0, 60, 1, 0 }, + { "ATX +5V", 9, 0, 30, 1, 0 }, + { "+3.3V", 10, 0, 20, 1, 0 }, + { "5VSB", 11, 0, 30, 1, 0 }, + { "CPU", 24, 1, 1, 1, 0 }, + { "System ", 25, 1, 1, 1, 0 }, + { "PWM1", 26, 1, 1, 1, 0 }, + { "PWM2", 27, 1, 1, 1, 0 }, + { "PWM3", 28, 1, 1, 1, 0 }, + { "PWM4", 29, 1, 1, 1, 0 }, + { "CPU Fan", 32, 2, 60, 1, 0 }, + { "NB Fan", 33, 2, 60, 1, 0 }, + { "SYS Fan", 34, 2, 60, 1, 0 }, + { "AUX1 Fan", 35, 2, 60, 1, 0 }, + { "AUX2 Fan", 36, 2, 60, 1, 0 }, + { "AUX3 Fan", 37, 2, 60, 1, 0 }, + { "AUX4 Fan", 38, 2, 60, 1, 0 }, + { NULL, 0, 0, 0, 0, 0 } } + }, + { 0x0014, "unknown", { + { "CPU Core", 0, 0, 10, 1, 0 }, + { "DDR", 1, 0, 10, 1, 0 }, + { "DDR VTT", 2, 0, 10, 1, 0 }, + { "CPU VTT 1.2V", 3, 0, 10, 1, 0 }, + { "MCH & PCIE 1.5V", 4, 0, 10, 1, 0 }, + { "MCH 2.5V", 5, 0, 20, 1, 0 }, + { "ICH 1.05V", 6, 0, 10, 1, 0 }, + { "ATX +12V (24-Pin)", 7, 0, 60, 1, 0 }, + { "ATX +12V (4-pin)", 8, 0, 60, 1, 0 }, + { "ATX +5V", 9, 0, 30, 1, 0 }, + { "+3.3V", 10, 0, 20, 1, 0 }, + { "5VSB", 11, 0, 30, 1, 0 }, + { "CPU", 24, 1, 1, 1, 0 }, + { "System ", 25, 1, 1, 1, 0 }, + { "PWM", 26, 1, 1, 1, 0 }, + { "CPU Fan", 32, 2, 60, 1, 0 }, + { "NB Fan", 33, 2, 60, 1, 0 }, + { "SYS Fan", 34, 2, 60, 1, 0 }, + { NULL, 0, 0, 0, 0, 0 } } + }, + { 0x0015, "unknown", { + { "CPU Core", 0, 0, 10, 1, 0 }, + { "DDR", 1, 0, 20, 1, 0 }, + { "DDR VTT", 2, 0, 10, 1, 0 }, + { "HyperTransport", 3, 0, 10, 1, 0 }, + { "CPU VDDA 2.5V", 5, 0, 20, 1, 0 }, + { "NB", 4, 0, 10, 1, 0 }, + { "SB", 6, 0, 10, 1, 0 }, + { "ATX +12V (24-Pin)", 7, 0, 60, 1, 0 }, + { "ATX +12V (4-pin)", 8, 0, 60, 1, 0 }, + { "ATX +5V", 9, 0, 30, 1, 0 }, + { "+3.3V", 10, 0, 20, 1, 0 }, + { "5VSB", 11, 0, 30, 1, 0 }, + { "CPU", 24, 1, 1, 1, 0 }, + { "SYS", 25, 1, 1, 1, 0 }, + { "PWM", 26, 1, 1, 1, 0 }, + { "CPU Fan", 32, 2, 60, 1, 0 }, + { "NB Fan", 33, 2, 60, 1, 0 }, + { "SYS Fan", 34, 2, 60, 1, 0 }, + { "AUX1 Fan", 33, 2, 60, 1, 0 }, + { "AUX2 Fan", 35, 2, 60, 1, 0 }, + { "AUX3 Fan", 36, 2, 60, 1, 0 }, + { NULL, 0, 0, 0, 0, 0 } } + }, + { 0x0016, "AW9D-MAX", { + { "CPU Core", 0, 0, 10, 1, 0 }, + { "DDR2", 1, 0, 20, 1, 0 }, + { "DDR2 VTT", 2, 0, 10, 1, 0 }, + { "CPU VTT 1.2V", 3, 0, 10, 1, 0 }, + { "MCH & PCIE 1.5V", 4, 0, 10, 1, 0 }, + { "MCH 2.5V", 5, 0, 20, 1, 0 }, + { "ICH 1.05V", 6, 0, 10, 1, 0 }, + { "ATX +12V (24-Pin)", 7, 0, 60, 1, 0 }, + { "ATX +12V (4-pin)", 8, 0, 60, 1, 0 }, + { "ATX +5V", 9, 0, 30, 1, 0 }, + { "+3.3V", 10, 0, 20, 1, 0 }, + { "5VSB", 11, 0, 30, 1, 0 }, + { "CPU", 24, 1, 1, 1, 0 }, + { "System ", 25, 1, 1, 1, 0 }, + { "PWM1", 26, 1, 1, 1, 0 }, + { "PWM2", 27, 1, 1, 1, 0 }, + { "PWM3", 28, 1, 1, 1, 0 }, + { "PWM4", 29, 1, 1, 1, 0 }, + { "CPU Fan", 32, 2, 60, 1, 0 }, + { "NB Fan", 33, 2, 60, 1, 0 }, + { "SYS Fan", 34, 2, 60, 1, 0 }, + { "AUX1 Fan", 35, 2, 60, 1, 0 }, + { "AUX2 Fan", 36, 2, 60, 1, 0 }, + { "AUX3 Fan", 37, 2, 60, 1, 0 }, + { "OTES1 Fan", 38, 2, 60, 1, 0 }, + { NULL, 0, 0, 0, 0, 0 } } + }, + { 0x0017, "unknown", { + { "CPU Core", 0, 0, 10, 1, 0 }, + { "DDR2", 1, 0, 20, 1, 0 }, + { "DDR2 VTT", 2, 0, 10, 1, 0 }, + { "HyperTransport", 3, 0, 10, 1, 0 }, + { "CPU VDDA 2.5V", 6, 0, 20, 1, 0 }, + { "NB 1.8V", 4, 0, 10, 1, 0 }, + { "NB 1.2V ", 13, 0, 10, 1, 0 }, + { "SB 1.2V", 5, 0, 10, 1, 0 }, + { "PCIE 1.2V", 12, 0, 10, 1, 0 }, + { "ATX +12V (24-Pin)", 7, 0, 60, 1, 0 }, + { "ATX +12V (4-pin)", 8, 0, 60, 1, 0 }, + { "ATX +5V", 9, 0, 30, 1, 0 }, + { "ATX +3.3V", 10, 0, 20, 1, 0 }, + { "ATX 5VSB", 11, 0, 30, 1, 0 }, + { "CPU", 24, 1, 1, 1, 0 }, + { "System ", 26, 1, 1, 1, 0 }, + { "PWM", 27, 1, 1, 1, 0 }, + { "CPU FAN", 32, 2, 60, 1, 0 }, + { "SYS FAN", 34, 2, 60, 1, 0 }, + { "AUX1 FAN", 35, 2, 60, 1, 0 }, + { "AUX2 FAN", 36, 2, 60, 1, 0 }, + { "AUX3 FAN", 37, 2, 60, 1, 0 }, + { NULL, 0, 0, 0, 0, 0 } } + }, + { 0x0018, "unknown", { + { "CPU Core", 0, 0, 10, 1, 0 }, + { "DDR2", 1, 0, 20, 1, 0 }, + { "DDR2 VTT", 2, 0, 10, 1, 0 }, + { "CPU VTT", 3, 0, 10, 1, 0 }, + { "MCH 1.25V", 4, 0, 10, 1, 0 }, + { "ICHIO 1.5V", 5, 0, 10, 1, 0 }, + { "ICH 1.05V", 6, 0, 10, 1, 0 }, + { "ATX +12V (24-Pin)", 7, 0, 60, 1, 0 }, + { "ATX +12V (4-pin)", 8, 0, 60, 1, 0 }, + { "ATX +5V", 9, 0, 30, 1, 0 }, + { "+3.3V", 10, 0, 20, 1, 0 }, + { "5VSB", 11, 0, 30, 1, 0 }, + { "CPU", 24, 1, 1, 1, 0 }, + { "System ", 25, 1, 1, 1, 0 }, + { "PWM Phase1", 26, 1, 1, 1, 0 }, + { "PWM Phase2", 27, 1, 1, 1, 0 }, + { "PWM Phase3", 28, 1, 1, 1, 0 }, + { "PWM Phase4", 29, 1, 1, 1, 0 }, + { "PWM Phase5", 30, 1, 1, 1, 0 }, + { "CPU Fan", 32, 2, 60, 1, 0 }, + { "SYS Fan", 34, 2, 60, 1, 0 }, + { "AUX1 Fan", 33, 2, 60, 1, 0 }, + { "AUX2 Fan", 35, 2, 60, 1, 0 }, + { "AUX3 Fan", 36, 2, 60, 1, 0 }, + { NULL, 0, 0, 0, 0, 0 } } + }, + { 0x0019, "unknown", { + { "CPU Core", 7, 0, 10, 1, 0 }, + { "DDR2", 13, 0, 20, 1, 0 }, + { "DDR2 VTT", 14, 0, 10, 1, 0 }, + { "CPU VTT", 3, 0, 20, 1, 0 }, + { "NB 1.2V ", 4, 0, 10, 1, 0 }, + { "SB 1.5V", 6, 0, 10, 1, 0 }, + { "HyperTransport", 5, 0, 10, 1, 0 }, + { "ATX +12V (24-Pin)", 12, 0, 60, 1, 0 }, + { "ATX +12V (4-pin)", 8, 0, 60, 1, 0 }, + { "ATX +5V", 9, 0, 30, 1, 0 }, + { "ATX +3.3V", 10, 0, 20, 1, 0 }, + { "ATX 5VSB", 11, 0, 30, 1, 0 }, + { "CPU", 24, 1, 1, 1, 0 }, + { "System ", 25, 1, 1, 1, 0 }, + { "PWM Phase1", 26, 1, 1, 1, 0 }, + { "PWM Phase2", 27, 1, 1, 1, 0 }, + { "PWM Phase3", 28, 1, 1, 1, 0 }, + { "PWM Phase4", 29, 1, 1, 1, 0 }, + { "PWM Phase5", 30, 1, 1, 1, 0 }, + { "CPU FAN", 32, 2, 60, 1, 0 }, + { "SYS FAN", 34, 2, 60, 1, 0 }, + { "AUX1 FAN", 33, 2, 60, 1, 0 }, + { "AUX2 FAN", 35, 2, 60, 1, 0 }, + { "AUX3 FAN", 36, 2, 60, 1, 0 }, + { NULL, 0, 0, 0, 0, 0 } } + }, + { 0x001A, "unknown", { + { "CPU Core", 0, 0, 10, 1, 0 }, + { "DDR2", 1, 0, 20, 1, 0 }, + { "DDR2 VTT", 2, 0, 10, 1, 0 }, + { "CPU VTT 1.2V", 3, 0, 10, 1, 0 }, + { "MCH 1.25V", 4, 0, 10, 1, 0 }, + { "ICHIO 1.5V", 5, 0, 10, 1, 0 }, + { "ICH 1.05V", 6, 0, 10, 1, 0 }, + { "ATX +12V (24-Pin)", 7, 0, 60, 1, 0 }, + { "ATX +12V (8-pin)", 8, 0, 60, 1, 0 }, + { "ATX +5V", 9, 0, 30, 1, 0 }, + { "+3.3V", 10, 0, 20, 1, 0 }, + { "5VSB", 11, 0, 30, 1, 0 }, + { "CPU", 24, 1, 1, 1, 0 }, + { "System ", 25, 1, 1, 1, 0 }, + { "PWM ", 26, 1, 1, 1, 0 }, + { "PWM Phase2", 27, 1, 1, 1, 0 }, + { "PWM Phase3", 28, 1, 1, 1, 0 }, + { "PWM Phase4", 29, 1, 1, 1, 0 }, + { "PWM Phase5", 30, 1, 1, 1, 0 }, + { "CPU Fan", 32, 2, 60, 1, 0 }, + { "SYS Fan", 34, 2, 60, 1, 0 }, + { "AUX1 Fan", 33, 2, 60, 1, 0 }, + { "AUX2 Fan", 35, 2, 60, 1, 0 }, + { "AUX3 Fan", 36, 2, 60, 1, 0 }, + { NULL, 0, 0, 0, 0, 0 } } + }, + { 0x0000, NULL, { { NULL, 0, 0, 0, 0, 0 } } } +}; + + +/* Insmod parameters */ +static int force; +module_param(force, bool, 0); +MODULE_PARM_DESC(force, "Set to one to force detection."); +/* Default verbose is 1, since this driver is still in the testing phase */ +static int verbose = 1; +module_param(verbose, bool, 0644); +MODULE_PARM_DESC(verbose, "Enable/disable verbose error reporting"); + + +/* wait while the uguru is busy (usually after a write) */ +static int abituguru3_wait_while_busy(struct abituguru3_data *data) +{ + u8 x; + int timeout = ABIT_UGURU3_WAIT_TIMEOUT; + + while ((x = inb_p(data->addr + ABIT_UGURU3_DATA)) & + ABIT_UGURU3_STATUS_BUSY) { + timeout--; + if (timeout == 0) + return x; + /* sleep a bit before our last try, to give the uGuru3 one + last chance to respond. */ + if (timeout == 1) + msleep(1); + } + return ABIT_UGURU3_SUCCESS; +} + +/* wait till uguru is ready to be read */ +static int abituguru3_wait_for_read(struct abituguru3_data *data) +{ + u8 x; + int timeout = ABIT_UGURU3_WAIT_TIMEOUT; + + while (!((x = inb_p(data->addr + ABIT_UGURU3_DATA)) & + ABIT_UGURU3_STATUS_READY_FOR_READ)) { + timeout--; + if (timeout == 0) + return x; + /* sleep a bit before our last try, to give the uGuru3 one + last chance to respond. */ + if (timeout == 1) + msleep(1); + } + return ABIT_UGURU3_SUCCESS; +} + +/* This synchronizes us with the uGuru3's protocol state machine, this + must be done before each command. */ +static int abituguru3_synchronize(struct abituguru3_data *data) +{ + int x, timeout = ABIT_UGURU3_SYNCHRONIZE_TIMEOUT; + + if ((x = abituguru3_wait_while_busy(data)) != ABIT_UGURU3_SUCCESS) { + ABIT_UGURU3_DEBUG("synchronize timeout during initial busy " + "wait, status: 0x%02x\n", x); + return -EIO; + } + + outb(0x20, data->addr + ABIT_UGURU3_DATA); + if ((x = abituguru3_wait_while_busy(data)) != ABIT_UGURU3_SUCCESS) { + ABIT_UGURU3_DEBUG("synchronize timeout after sending 0x20, " + "status: 0x%02x\n", x); + return -EIO; + } + + outb(0x10, data->addr + ABIT_UGURU3_CMD); + if ((x = abituguru3_wait_while_busy(data)) != ABIT_UGURU3_SUCCESS) { + ABIT_UGURU3_DEBUG("synchronize timeout after sending 0x10, " + "status: 0x%02x\n", x); + return -EIO; + } + + outb(0x00, data->addr + ABIT_UGURU3_CMD); + if ((x = abituguru3_wait_while_busy(data)) != ABIT_UGURU3_SUCCESS) { + ABIT_UGURU3_DEBUG("synchronize timeout after sending 0x00, " + "status: 0x%02x\n", x); + return -EIO; + } + + if ((x = abituguru3_wait_for_read(data)) != ABIT_UGURU3_SUCCESS) { + ABIT_UGURU3_DEBUG("synchronize timeout waiting for read, " + "status: 0x%02x\n", x); + return -EIO; + } + + while ((x = inb(data->addr + ABIT_UGURU3_CMD)) != 0xAC) { + timeout--; + if (timeout == 0) { + ABIT_UGURU3_DEBUG("synchronize timeout cmd does not " + "hold 0xAC after synchronize, cmd: 0x%02x\n", + x); + return -EIO; + } + msleep(1); + } + return 0; +} + +/* Read count bytes from sensor sensor_addr in bank bank_addr and store the + result in buf */ +static int abituguru3_read(struct abituguru3_data *data, u8 bank, u8 offset, + u8 count, u8 *buf) +{ + int i, x; + + if ((x = abituguru3_synchronize(data))) + return x; + + outb(0x1A, data->addr + ABIT_UGURU3_DATA); + if ((x = abituguru3_wait_while_busy(data)) != ABIT_UGURU3_SUCCESS) { + ABIT_UGURU3_DEBUG("read from 0x%02x:0x%02x timed out after " + "sending 0x1A, status: 0x%02x\n", (unsigned int)bank, + (unsigned int)offset, x); + return -EIO; + } + + outb(bank, data->addr + ABIT_UGURU3_CMD); + if ((x = abituguru3_wait_while_busy(data)) != ABIT_UGURU3_SUCCESS) { + ABIT_UGURU3_DEBUG("read from 0x%02x:0x%02x timed out after " + "sending the bank, status: 0x%02x\n", + (unsigned int)bank, (unsigned int)offset, x); + return -EIO; + } + + outb(offset, data->addr + ABIT_UGURU3_CMD); + if ((x = abituguru3_wait_while_busy(data)) != ABIT_UGURU3_SUCCESS) { + ABIT_UGURU3_DEBUG("read from 0x%02x:0x%02x timed out after " + "sending the offset, status: 0x%02x\n", + (unsigned int)bank, (unsigned int)offset, x); + return -EIO; + } + + outb(count, data->addr + ABIT_UGURU3_CMD); + if ((x = abituguru3_wait_while_busy(data)) != ABIT_UGURU3_SUCCESS) { + ABIT_UGURU3_DEBUG("read from 0x%02x:0x%02x timed out after " + "sending the count, status: 0x%02x\n", + (unsigned int)bank, (unsigned int)offset, x); + return -EIO; + } + + for (i = 0; i < count; i++) { + if ((x = abituguru3_wait_for_read(data)) != + ABIT_UGURU3_SUCCESS) { + ABIT_UGURU3_DEBUG("timeout reading byte %d from " + "0x%02x:0x%02x, status: 0x%02x\n", i, + (unsigned int)bank, (unsigned int)offset, x); + break; + } + buf[i] = inb(data->addr + ABIT_UGURU3_CMD); + } + return i; +} + +/* Sensor settings are stored 1 byte per offset with the bytes + placed add consecutive offsets. */ +int abituguru3_read_increment_offset(struct abituguru3_data *data, u8 bank, + u8 offset, u8 count, u8 *buf, int offset_count) +{ + int i, x; + + for (i = 0; i < offset_count; i++) + if ((x = abituguru3_read(data, bank, offset + i, count, + buf + i * count)) != count) + return i * count + (i && (x < 0)) ? 0 : x; + + return i * count; +} + +/* Following are the sysfs callback functions. These functions expect: + sensor_device_attribute_2->index: index into the data->sensors array + sensor_device_attribute_2->nr: register offset, bitmask or NA. */ +static struct abituguru3_data *abituguru3_update_device(struct device *dev); + +static ssize_t show_value(struct device *dev, + struct device_attribute *devattr, char *buf) +{ + int value; + struct sensor_device_attribute_2 *attr = to_sensor_dev_attr_2(devattr); + struct abituguru3_data *data = abituguru3_update_device(dev); + const struct abituguru3_sensor_info *sensor; + + if (!data) + return -EIO; + + sensor = &data->sensors[attr->index]; + + /* are we reading a setting, or is this a normal read? */ + if (attr->nr) + value = data->settings[sensor->port][attr->nr]; + else + value = data->value[sensor->port]; + + /* convert the value */ + value = (value * sensor->multiplier) / sensor->divisor + + sensor->offset; + + /* alternatively we could update the sensors settings struct for this, + but then its contents would differ from the windows sw ini files */ + if (sensor->type == ABIT_UGURU3_TEMP_SENSOR) + value *= 1000; + + return sprintf(buf, "%d\n", value); +} + +static ssize_t show_alarm(struct device *dev, + struct device_attribute *devattr, char *buf) +{ + int port; + struct sensor_device_attribute_2 *attr = to_sensor_dev_attr_2(devattr); + struct abituguru3_data *data = abituguru3_update_device(dev); + + if (!data) + return -EIO; + + port = data->sensors[attr->index].port; + + /* See if the alarm bit for this sensor is set and if a bitmask is + given in attr->nr also check if the alarm matches the type of alarm + we're looking for (for volt it can be either low or high). The type + is stored in a few readonly bits in the settings of the sensor. */ + if ((data->alarms[port / 8] & (0x01 << (port % 8))) && + (!attr->nr || (data->settings[port][0] & attr->nr))) + return sprintf(buf, "1\n"); + else + return sprintf(buf, "0\n"); +} + +static ssize_t show_mask(struct device *dev, + struct device_attribute *devattr, char *buf) +{ + struct sensor_device_attribute_2 *attr = to_sensor_dev_attr_2(devattr); + struct abituguru3_data *data = dev_get_drvdata(dev); + + if (data->settings[data->sensors[attr->index].port][0] & attr->nr) + return sprintf(buf, "1\n"); + else + return sprintf(buf, "0\n"); +} + +static ssize_t show_label(struct device *dev, + struct device_attribute *devattr, char *buf) +{ + struct sensor_device_attribute_2 *attr = to_sensor_dev_attr_2(devattr); + struct abituguru3_data *data = dev_get_drvdata(dev); + + return sprintf(buf, "%s\n", data->sensors[attr->index].name); +} + +static ssize_t show_name(struct device *dev, + struct device_attribute *devattr, char *buf) +{ + return sprintf(buf, "%s\n", ABIT_UGURU3_NAME); +} + +/* Sysfs attr templates, the real entries are generated automatically. */ +static const +struct sensor_device_attribute_2 abituguru3_sysfs_templ[3][10] = { { + SENSOR_ATTR_2(in%d_input, 0444, show_value, NULL, 0, 0), + SENSOR_ATTR_2(in%d_min, 0444, show_value, NULL, 1, 0), + SENSOR_ATTR_2(in%d_max, 0444, show_value, NULL, 2, 0), + SENSOR_ATTR_2(in%d_min_alarm, 0444, show_alarm, NULL, + ABIT_UGURU3_VOLT_LOW_ALARM_FLAG, 0), + SENSOR_ATTR_2(in%d_max_alarm, 0444, show_alarm, NULL, + ABIT_UGURU3_VOLT_HIGH_ALARM_FLAG, 0), + SENSOR_ATTR_2(in%d_beep, 0444, show_mask, NULL, + ABIT_UGURU3_BEEP_ENABLE, 0), + SENSOR_ATTR_2(in%d_shutdown, 0444, show_mask, NULL, + ABIT_UGURU3_SHUTDOWN_ENABLE, 0), + SENSOR_ATTR_2(in%d_min_alarm_enable, 0444, show_mask, NULL, + ABIT_UGURU3_VOLT_LOW_ALARM_ENABLE, 0), + SENSOR_ATTR_2(in%d_max_alarm_enable, 0444, show_mask, NULL, + ABIT_UGURU3_VOLT_HIGH_ALARM_ENABLE, 0), + SENSOR_ATTR_2(in%d_label, 0444, show_label, NULL, 0, 0) + }, { + SENSOR_ATTR_2(temp%d_input, 0444, show_value, NULL, 0, 0), + SENSOR_ATTR_2(temp%d_max, 0444, show_value, NULL, 1, 0), + SENSOR_ATTR_2(temp%d_crit, 0444, show_value, NULL, 2, 0), + SENSOR_ATTR_2(temp%d_alarm, 0444, show_alarm, NULL, 0, 0), + SENSOR_ATTR_2(temp%d_beep, 0444, show_mask, NULL, + ABIT_UGURU3_BEEP_ENABLE, 0), + SENSOR_ATTR_2(temp%d_shutdown, 0444, show_mask, NULL, + ABIT_UGURU3_SHUTDOWN_ENABLE, 0), + SENSOR_ATTR_2(temp%d_alarm_enable, 0444, show_mask, NULL, + ABIT_UGURU3_TEMP_HIGH_ALARM_ENABLE, 0), + SENSOR_ATTR_2(temp%d_label, 0444, show_label, NULL, 0, 0) + }, { + SENSOR_ATTR_2(fan%d_input, 0444, show_value, NULL, 0, 0), + SENSOR_ATTR_2(fan%d_min, 0444, show_value, NULL, 1, 0), + SENSOR_ATTR_2(fan%d_alarm, 0444, show_alarm, NULL, 0, 0), + SENSOR_ATTR_2(fan%d_beep, 0444, show_mask, NULL, + ABIT_UGURU3_BEEP_ENABLE, 0), + SENSOR_ATTR_2(fan%d_shutdown, 0444, show_mask, NULL, + ABIT_UGURU3_SHUTDOWN_ENABLE, 0), + SENSOR_ATTR_2(fan%d_alarm_enable, 0444, show_mask, NULL, + ABIT_UGURU3_FAN_LOW_ALARM_ENABLE, 0), + SENSOR_ATTR_2(fan%d_label, 0444, show_label, NULL, 0, 0) +} }; + +static struct sensor_device_attribute_2 abituguru3_sysfs_attr[] = { + SENSOR_ATTR_2(name, 0444, show_name, NULL, 0, 0), +}; + +static int __devinit abituguru3_probe(struct platform_device *pdev) +{ + const int no_sysfs_attr[3] = { 10, 8, 7 }; + int sensor_index[3] = { 0, 1, 1 }; + struct abituguru3_data *data; + int i, j, type, used, sysfs_names_free, sysfs_attr_i, res = -ENODEV; + char *sysfs_filename; + u8 buf[2]; + u16 id; + + if (!(data = kzalloc(sizeof(struct abituguru3_data), GFP_KERNEL))) + return -ENOMEM; + + data->addr = platform_get_resource(pdev, IORESOURCE_IO, 0)->start; + mutex_init(&data->update_lock); + platform_set_drvdata(pdev, data); + + /* Read the motherboard ID */ + if ((i = abituguru3_read(data, ABIT_UGURU3_MISC_BANK, + ABIT_UGURU3_BOARD_ID, 2, buf)) != 2) { + goto abituguru3_probe_error; + } + + /* Completely read the uGuru to see if one really is there */ + if (!abituguru3_update_device(&pdev->dev)) + goto abituguru3_probe_error; + + /* lookup the ID in our motherboard table */ + id = ((u16)buf[0] << 8) | (u16)buf[1]; + for (i = 0; abituguru3_motherboards[i].id; i++) + if (abituguru3_motherboards[i].id == id) + break; + if (!abituguru3_motherboards[i].id) { + printk(KERN_ERR ABIT_UGURU3_NAME ": error unknown motherboard " + "ID: %04X. Please report this to the abituguru3 " + "maintainer (see MAINTAINERS)\n", (unsigned int)id); + goto abituguru3_probe_error; + } + data->sensors = abituguru3_motherboards[i].sensors; + printk(KERN_INFO ABIT_UGURU3_NAME ": found Abit uGuru3, motherboard " + "ID: %04X (%s)\n", (unsigned int)id, + abituguru3_motherboards[i].name); + + /* Fill the sysfs attr array */ + sysfs_attr_i = 0; + sysfs_filename = data->sysfs_names; + sysfs_names_free = ABIT_UGURU3_SYSFS_NAMES_LENGTH; + for (i = 0; data->sensors[i].name; i++) { + /* Fail safe check, this should never happen! */ + if (i >= ABIT_UGURU3_MAX_NO_SENSORS) { + printk(KERN_ERR ABIT_UGURU3_NAME + ": Fatal error motherboard has more sensors " + "then ABIT_UGURU3_MAX_NO_SENSORS. This should " + "never happen please report to the abituguru3 " + "maintainer (see MAINTAINERS)\n"); + res = -ENAMETOOLONG; + goto abituguru3_probe_error; + } + type = data->sensors[i].type; + for (j = 0; j < no_sysfs_attr[type]; j++) { + used = snprintf(sysfs_filename, sysfs_names_free, + abituguru3_sysfs_templ[type][j].dev_attr.attr. + name, sensor_index[type]) + 1; + data->sysfs_attr[sysfs_attr_i] = + abituguru3_sysfs_templ[type][j]; + data->sysfs_attr[sysfs_attr_i].dev_attr.attr.name = + sysfs_filename; + data->sysfs_attr[sysfs_attr_i].index = i; + sysfs_filename += used; + sysfs_names_free -= used; + sysfs_attr_i++; + } + sensor_index[type]++; + } + /* Fail safe check, this should never happen! */ + if (sysfs_names_free < 0) { + printk(KERN_ERR ABIT_UGURU3_NAME + ": Fatal error ran out of space for sysfs attr names. " + "This should never happen please report to the " + "abituguru3 maintainer (see MAINTAINERS)\n"); + res = -ENAMETOOLONG; + goto abituguru3_probe_error; + } + + /* Register sysfs hooks */ + for (i = 0; i < sysfs_attr_i; i++) + if (device_create_file(&pdev->dev, + &data->sysfs_attr[i].dev_attr)) + goto abituguru3_probe_error; + for (i = 0; i < ARRAY_SIZE(abituguru3_sysfs_attr); i++) + if (device_create_file(&pdev->dev, + &abituguru3_sysfs_attr[i].dev_attr)) + goto abituguru3_probe_error; + + data->class_dev = hwmon_device_register(&pdev->dev); + if (IS_ERR(data->class_dev)) { + res = PTR_ERR(data->class_dev); + goto abituguru3_probe_error; + } + + return 0; /* success */ + +abituguru3_probe_error: + for (i = 0; data->sysfs_attr[i].dev_attr.attr.name; i++) + device_remove_file(&pdev->dev, &data->sysfs_attr[i].dev_attr); + for (i = 0; i < ARRAY_SIZE(abituguru3_sysfs_attr); i++) + device_remove_file(&pdev->dev, + &abituguru3_sysfs_attr[i].dev_attr); + kfree(data); + return res; +} + +static int __devexit abituguru3_remove(struct platform_device *pdev) +{ + int i; + struct abituguru3_data *data = platform_get_drvdata(pdev); + + platform_set_drvdata(pdev, NULL); + hwmon_device_unregister(data->class_dev); + for (i = 0; data->sysfs_attr[i].dev_attr.attr.name; i++) + device_remove_file(&pdev->dev, &data->sysfs_attr[i].dev_attr); + for (i = 0; i < ARRAY_SIZE(abituguru3_sysfs_attr); i++) + device_remove_file(&pdev->dev, + &abituguru3_sysfs_attr[i].dev_attr); + kfree(data); + + return 0; +} + +static struct abituguru3_data *abituguru3_update_device(struct device *dev) +{ + int i; + struct abituguru3_data *data = dev_get_drvdata(dev); + + mutex_lock(&data->update_lock); + if (!data->valid || time_after(jiffies, data->last_updated + HZ)) { + /* Clear data->valid while updating */ + data->valid = 0; + /* Read alarms */ + if (abituguru3_read_increment_offset(data, + ABIT_UGURU3_SETTINGS_BANK, + ABIT_UGURU3_ALARMS_START, + 1, data->alarms, 48/8) != (48/8)) + goto LEAVE_UPDATE; + /* Read in and temp sensors (3 byte settings / sensor) */ + for (i = 0; i < 32; i++) { + if (abituguru3_read(data, ABIT_UGURU3_SENSORS_BANK, + ABIT_UGURU3_VALUES_START + i, + 1, &data->value[i]) != 1) + goto LEAVE_UPDATE; + if (abituguru3_read_increment_offset(data, + ABIT_UGURU3_SETTINGS_BANK, + ABIT_UGURU3_SETTINGS_START + i * 3, + 1, + data->settings[i], 3) != 3) + goto LEAVE_UPDATE; + } + /* Read temp sensors (2 byte settings / sensor) */ + for (i = 0; i < 16; i++) { + if (abituguru3_read(data, ABIT_UGURU3_SENSORS_BANK, + ABIT_UGURU3_VALUES_START + 32 + i, + 1, &data->value[32 + i]) != 1) + goto LEAVE_UPDATE; + if (abituguru3_read_increment_offset(data, + ABIT_UGURU3_SETTINGS_BANK, + ABIT_UGURU3_SETTINGS_START + 32 * 3 + + i * 2, 1, + data->settings[32 + i], 2) != 2) + goto LEAVE_UPDATE; + } + data->last_updated = jiffies; + data->valid = 1; + } +LEAVE_UPDATE: + mutex_unlock(&data->update_lock); + if (data->valid) + return data; + else + return NULL; +} + +#ifdef CONFIG_PM +static int abituguru3_suspend(struct platform_device *pdev, pm_message_t state) +{ + struct abituguru3_data *data = platform_get_drvdata(pdev); + /* make sure all communications with the uguru3 are done and no new + ones are started */ + mutex_lock(&data->update_lock); + return 0; +} + +static int abituguru3_resume(struct platform_device *pdev) +{ + struct abituguru3_data *data = platform_get_drvdata(pdev); + mutex_unlock(&data->update_lock); + return 0; +} +#else +#define abituguru3_suspend NULL +#define abituguru3_resume NULL +#endif /* CONFIG_PM */ + +static struct platform_driver abituguru3_driver = { + .driver = { + .owner = THIS_MODULE, + .name = ABIT_UGURU3_NAME, + }, + .probe = abituguru3_probe, + .remove = __devexit_p(abituguru3_remove), + .suspend = abituguru3_suspend, + .resume = abituguru3_resume +}; + +static int __init abituguru3_detect(void) +{ + /* See if there is an uguru3 there. An idle uGuru3 will hold 0x00 + at DATA and 0xAC at CMD. Sometimes the uGuru3 will hold 0x05 at + CMD instead, why is unknown. So we test for 0x05 too. */ + u8 data_val = inb_p(ABIT_UGURU3_BASE + ABIT_UGURU3_DATA); + u8 cmd_val = inb_p(ABIT_UGURU3_BASE + ABIT_UGURU3_CMD); + if ((data_val == 0x00) && ((cmd_val == 0xAC) || (cmd_val == 0x05))) + return ABIT_UGURU3_BASE; + + ABIT_UGURU3_DEBUG("no Abit uGuru3 found, data = 0x%02X, cmd = " + "0x%02X\n", (unsigned int)data_val, (unsigned int)cmd_val); + + if (force) { + printk(KERN_INFO ABIT_UGURU3_NAME ": Assuming Abit uGuru3 is " + "present because of \"force\" parameter\n"); + return ABIT_UGURU3_BASE; + } + + /* No uGuru3 found */ + return -ENODEV; +} + +static struct platform_device *abituguru3_pdev; + +static int __init abituguru3_init(void) +{ + int address, err; + struct resource res = { .flags = IORESOURCE_IO }; + + address = abituguru3_detect(); + if (address < 0) + return address; + + err = platform_driver_register(&abituguru3_driver); + if (err) + goto exit; + + abituguru3_pdev = platform_device_alloc(ABIT_UGURU3_NAME, address); + if (!abituguru3_pdev) { + printk(KERN_ERR ABIT_UGURU3_NAME + ": Device allocation failed\n"); + err = -ENOMEM; + goto exit_driver_unregister; + } + + res.start = address; + res.end = address + ABIT_UGURU3_REGION_LENGTH - 1; + res.name = ABIT_UGURU3_NAME; + + err = platform_device_add_resources(abituguru3_pdev, &res, 1); + if (err) { + printk(KERN_ERR ABIT_UGURU3_NAME + ": Device resource addition failed (%d)\n", err); + goto exit_device_put; + } + + err = platform_device_add(abituguru3_pdev); + if (err) { + printk(KERN_ERR ABIT_UGURU3_NAME + ": Device addition failed (%d)\n", err); + goto exit_device_put; + } + + return 0; + +exit_device_put: + platform_device_put(abituguru3_pdev); +exit_driver_unregister: + platform_driver_unregister(&abituguru3_driver); +exit: + return err; +} + +static void __exit abituguru3_exit(void) +{ + platform_device_unregister(abituguru3_pdev); + platform_driver_unregister(&abituguru3_driver); +} + +MODULE_AUTHOR("Hans de Goede "); +MODULE_DESCRIPTION("Abit uGuru3 Sensor device"); +MODULE_LICENSE("GPL"); + +module_init(abituguru3_init); +module_exit(abituguru3_exit); -- 2.20.1