From 3be91ec7388bae3cf1bfb4febcee5ab6c65f409f Mon Sep 17 00:00:00 2001
From: Zang Roy-r61911 <tie-fei.zang@freescale.com>
Date: Fri, 30 Jun 2006 02:29:58 -0700
Subject: [PATCH] [SERIAL] 8250: add tsi108 serial support

The following patch gets rid of CONFIG_TSI108_BRIDGE.  I add UPIO_TSI to
handle IIR and IER register in serial_in and serial_out.

(1) the reason to rewrite serial_in:

    TSI108 rev Z1 version ERRATA.  Reading the UART's Interrupt
    Identification Register (IIR) clears the Transmit Holding Register
    Empty (THRE) and Transmit buffer Empty (TEMP) interrupts even if they
    are not enabled in the Interrupt Enable Register (IER).  This leads to
    loss of the interrupts.  Interrupts are not cleared when reading UART
    registers as 32-bit word.

(2) the reason to rewrite serial_out:

    Check for UART_IER_UUE bit in the autoconfig routine.  This section
    of autoconfig is excluded for Tsi108/109 because bits 7 and 6 are
    reserved for internal use.  They are R/W bits.  In addition to
    incorrect identification, changing these bits (from 00) will make
    Tsi108/109 UART non-functional.

Signed-off-by: Roy Zang	<tie-fei.zang@freescale.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
---
 drivers/serial/8250.c        | 12 ++++++++++++
 drivers/serial/serial_core.c |  1 +
 include/linux/serial_core.h  |  1 +
 3 files changed, 14 insertions(+)

diff --git a/drivers/serial/8250.c b/drivers/serial/8250.c
index 0995430e4cf1..5443fcd38355 100644
--- a/drivers/serial/8250.c
+++ b/drivers/serial/8250.c
@@ -299,6 +299,7 @@ static inline int map_8250_out_reg(struct uart_8250_port *up, int offset)
 
 static unsigned int serial_in(struct uart_8250_port *up, int offset)
 {
+	unsigned int tmp;
 	offset = map_8250_in_reg(up, offset) << up->port.regshift;
 
 	switch (up->port.iotype) {
@@ -317,6 +318,13 @@ static unsigned int serial_in(struct uart_8250_port *up, int offset)
 		return __raw_readl(up->port.membase + offset);
 #endif
 
+	case UPIO_TSI:
+		if (offset == UART_IIR) {
+			tmp = readl((u32 *)(up->port.membase + UART_RX));
+			return (cpu_to_le32(tmp) >> 8) & 0xff;
+		} else
+			return readb(up->port.membase + offset);
+
 	default:
 		return inb(up->port.iobase + offset);
 	}
@@ -346,6 +354,10 @@ serial_out(struct uart_8250_port *up, int offset, int value)
 		__raw_writel(value, up->port.membase + offset);
 		break;
 #endif
+	case UPIO_TSI:
+		if (!((offset == UART_IER) && (value & UART_IER_UUE)))
+			writeb(value, up->port.membase + offset);
+		break;
 
 	default:
 		outb(value, up->port.iobase + offset);
diff --git a/drivers/serial/serial_core.c b/drivers/serial/serial_core.c
index d5f636fbf29a..80ef7d482756 100644
--- a/drivers/serial/serial_core.c
+++ b/drivers/serial/serial_core.c
@@ -2036,6 +2036,7 @@ uart_report_port(struct uart_driver *drv, struct uart_port *port)
 	case UPIO_MEM:
 	case UPIO_MEM32:
 	case UPIO_AU:
+	case UPIO_TSI:
 		snprintf(address, sizeof(address),
 			 "MMIO 0x%lx", port->mapbase);
 		break;
diff --git a/include/linux/serial_core.h b/include/linux/serial_core.h
index 058cba70818a..86501a3de2ac 100644
--- a/include/linux/serial_core.h
+++ b/include/linux/serial_core.h
@@ -227,6 +227,7 @@ struct uart_port {
 #define UPIO_MEM		(2)
 #define UPIO_MEM32		(3)
 #define UPIO_AU			(4)			/* Au1x00 type IO */
+#define UPIO_TSI		(5)			/* Tsi108/109 type IO */
 
 	unsigned int		read_status_mask;	/* driver specific */
 	unsigned int		ignore_status_mask;	/* driver specific */
-- 
2.20.1