From 2134a922c6e75c779983cad5d8aae832275f5a0d Mon Sep 17 00:00:00 2001 From: Pierre Ossman Date: Sat, 28 Jun 2008 18:28:51 +0200 Subject: [PATCH] sdhci: scatter-gather (ADMA) support Add support for the scatter-gather DMA mode present on newer controllers. As the mode requires 32-bit alignment, non-aligned chunks are handled by using a bounce buffer. Also add some new quirks to handle controllers that have bugs in the ADMA engine. Signed-off-by: Pierre Ossman --- drivers/mmc/host/sdhci-pci.c | 17 ++ drivers/mmc/host/sdhci.c | 383 +++++++++++++++++++++++++++++++---- drivers/mmc/host/sdhci.h | 51 ++++- 3 files changed, 407 insertions(+), 44 deletions(-) diff --git a/drivers/mmc/host/sdhci-pci.c b/drivers/mmc/host/sdhci-pci.c index 0716dcffd51..deb607c52c0 100644 --- a/drivers/mmc/host/sdhci-pci.c +++ b/drivers/mmc/host/sdhci-pci.c @@ -142,6 +142,7 @@ static int jmicron_probe(struct sdhci_pci_chip *chip) if (chip->pdev->revision == 0) { chip->quirks |= SDHCI_QUIRK_32BIT_DMA_ADDR | SDHCI_QUIRK_32BIT_DMA_SIZE | + SDHCI_QUIRK_32BIT_ADMA_SIZE | SDHCI_QUIRK_RESET_AFTER_REQUEST; } @@ -206,6 +207,22 @@ static void jmicron_enable_mmc(struct sdhci_host *host, int on) static int jmicron_probe_slot(struct sdhci_pci_slot *slot) { + if (slot->chip->pdev->revision == 0) { + u16 version; + + version = readl(slot->host->ioaddr + SDHCI_HOST_VERSION); + version = (version & SDHCI_VENDOR_VER_MASK) >> + SDHCI_VENDOR_VER_SHIFT; + + /* + * Older versions of the chip have lots of nasty glitches + * in the ADMA engine. It's best just to avoid it + * completely. + */ + if (version < 0xAC) + slot->host->quirks |= SDHCI_QUIRK_BROKEN_ADMA; + } + /* * The secondary interface requires a bit set to get the * interrupts. diff --git a/drivers/mmc/host/sdhci.c b/drivers/mmc/host/sdhci.c index 0ab582e77ac..b802044ea94 100644 --- a/drivers/mmc/host/sdhci.c +++ b/drivers/mmc/host/sdhci.c @@ -124,7 +124,8 @@ static void sdhci_init(struct sdhci_host *host) SDHCI_INT_END_BIT | SDHCI_INT_CRC | SDHCI_INT_TIMEOUT | SDHCI_INT_CARD_REMOVE | SDHCI_INT_CARD_INSERT | SDHCI_INT_DATA_AVAIL | SDHCI_INT_SPACE_AVAIL | - SDHCI_INT_DMA_END | SDHCI_INT_DATA_END | SDHCI_INT_RESPONSE; + SDHCI_INT_DMA_END | SDHCI_INT_DATA_END | SDHCI_INT_RESPONSE | + SDHCI_INT_ADMA_ERROR; writel(intmask, host->ioaddr + SDHCI_INT_ENABLE); writel(intmask, host->ioaddr + SDHCI_SIGNAL_ENABLE); @@ -314,6 +315,196 @@ static void sdhci_transfer_pio(struct sdhci_host *host) DBG("PIO transfer complete.\n"); } +static char *sdhci_kmap_atomic(struct scatterlist *sg, unsigned long *flags) +{ + local_irq_save(*flags); + return kmap_atomic(sg_page(sg), KM_BIO_SRC_IRQ) + sg->offset; +} + +static void sdhci_kunmap_atomic(void *buffer, unsigned long *flags) +{ + kunmap_atomic(buffer, KM_BIO_SRC_IRQ); + local_irq_restore(*flags); +} + +static void sdhci_adma_table_pre(struct sdhci_host *host, + struct mmc_data *data) +{ + int direction; + + u8 *desc; + u8 *align; + dma_addr_t addr; + dma_addr_t align_addr; + int len, offset; + + struct scatterlist *sg; + int i; + char *buffer; + unsigned long flags; + + /* + * The spec does not specify endianness of descriptor table. + * We currently guess that it is LE. + */ + + if (data->flags & MMC_DATA_READ) + direction = DMA_FROM_DEVICE; + else + direction = DMA_TO_DEVICE; + + /* + * The ADMA descriptor table is mapped further down as we + * need to fill it with data first. + */ + + host->align_addr = dma_map_single(mmc_dev(host->mmc), + host->align_buffer, 128 * 4, direction); + BUG_ON(host->align_addr & 0x3); + + host->sg_count = dma_map_sg(mmc_dev(host->mmc), + data->sg, data->sg_len, direction); + + desc = host->adma_desc; + align = host->align_buffer; + + align_addr = host->align_addr; + + for_each_sg(data->sg, sg, host->sg_count, i) { + addr = sg_dma_address(sg); + len = sg_dma_len(sg); + + /* + * The SDHCI specification states that ADMA + * addresses must be 32-bit aligned. If they + * aren't, then we use a bounce buffer for + * the (up to three) bytes that screw up the + * alignment. + */ + offset = (4 - (addr & 0x3)) & 0x3; + if (offset) { + if (data->flags & MMC_DATA_WRITE) { + buffer = sdhci_kmap_atomic(sg, &flags); + memcpy(align, buffer, offset); + sdhci_kunmap_atomic(buffer, &flags); + } + + desc[7] = (align_addr >> 24) & 0xff; + desc[6] = (align_addr >> 16) & 0xff; + desc[5] = (align_addr >> 8) & 0xff; + desc[4] = (align_addr >> 0) & 0xff; + + BUG_ON(offset > 65536); + + desc[3] = (offset >> 8) & 0xff; + desc[2] = (offset >> 0) & 0xff; + + desc[1] = 0x00; + desc[0] = 0x21; /* tran, valid */ + + align += 4; + align_addr += 4; + + desc += 8; + + addr += offset; + len -= offset; + } + + desc[7] = (addr >> 24) & 0xff; + desc[6] = (addr >> 16) & 0xff; + desc[5] = (addr >> 8) & 0xff; + desc[4] = (addr >> 0) & 0xff; + + BUG_ON(len > 65536); + + desc[3] = (len >> 8) & 0xff; + desc[2] = (len >> 0) & 0xff; + + desc[1] = 0x00; + desc[0] = 0x21; /* tran, valid */ + + desc += 8; + + /* + * If this triggers then we have a calculation bug + * somewhere. :/ + */ + WARN_ON((desc - host->adma_desc) > (128 * 2 + 1) * 4); + } + + /* + * Add a terminating entry. + */ + desc[7] = 0; + desc[6] = 0; + desc[5] = 0; + desc[4] = 0; + + desc[3] = 0; + desc[2] = 0; + + desc[1] = 0x00; + desc[0] = 0x03; /* nop, end, valid */ + + /* + * Resync align buffer as we might have changed it. + */ + if (data->flags & MMC_DATA_WRITE) { + dma_sync_single_for_device(mmc_dev(host->mmc), + host->align_addr, 128 * 4, direction); + } + + host->adma_addr = dma_map_single(mmc_dev(host->mmc), + host->adma_desc, (128 * 2 + 1) * 4, DMA_TO_DEVICE); + BUG_ON(host->adma_addr & 0x3); +} + +static void sdhci_adma_table_post(struct sdhci_host *host, + struct mmc_data *data) +{ + int direction; + + struct scatterlist *sg; + int i, size; + u8 *align; + char *buffer; + unsigned long flags; + + if (data->flags & MMC_DATA_READ) + direction = DMA_FROM_DEVICE; + else + direction = DMA_TO_DEVICE; + + dma_unmap_single(mmc_dev(host->mmc), host->adma_addr, + (128 * 2 + 1) * 4, DMA_TO_DEVICE); + + dma_unmap_single(mmc_dev(host->mmc), host->align_addr, + 128 * 4, direction); + + if (data->flags & MMC_DATA_READ) { + dma_sync_sg_for_cpu(mmc_dev(host->mmc), data->sg, + data->sg_len, direction); + + align = host->align_buffer; + + for_each_sg(data->sg, sg, host->sg_count, i) { + if (sg_dma_address(sg) & 0x3) { + size = 4 - (sg_dma_address(sg) & 0x3); + + buffer = sdhci_kmap_atomic(sg, &flags); + memcpy(buffer, align, size); + sdhci_kunmap_atomic(buffer, &flags); + + align += 4; + } + } + } + + dma_unmap_sg(mmc_dev(host->mmc), data->sg, + data->sg_len, direction); +} + static u8 sdhci_calc_timeout(struct sdhci_host *host, struct mmc_data *data) { u8 count; @@ -363,6 +554,7 @@ static u8 sdhci_calc_timeout(struct sdhci_host *host, struct mmc_data *data) static void sdhci_prepare_data(struct sdhci_host *host, struct mmc_data *data) { u8 count; + u8 ctrl; WARN_ON(host->data); @@ -383,35 +575,104 @@ static void sdhci_prepare_data(struct sdhci_host *host, struct mmc_data *data) if (host->flags & SDHCI_USE_DMA) host->flags |= SDHCI_REQ_USE_DMA; - if (unlikely((host->flags & SDHCI_REQ_USE_DMA) && - (host->quirks & SDHCI_QUIRK_32BIT_DMA_SIZE) && - ((data->blksz * data->blocks) & 0x3))) { - DBG("Reverting to PIO because of transfer size (%d)\n", - data->blksz * data->blocks); - host->flags &= ~SDHCI_REQ_USE_DMA; + /* + * FIXME: This doesn't account for merging when mapping the + * scatterlist. + */ + if (host->flags & SDHCI_REQ_USE_DMA) { + int broken, i; + struct scatterlist *sg; + + broken = 0; + if (host->flags & SDHCI_USE_ADMA) { + if (host->quirks & SDHCI_QUIRK_32BIT_ADMA_SIZE) + broken = 1; + } else { + if (host->quirks & SDHCI_QUIRK_32BIT_DMA_SIZE) + broken = 1; + } + + if (unlikely(broken)) { + for_each_sg(data->sg, sg, data->sg_len, i) { + if (sg->length & 0x3) { + DBG("Reverting to PIO because of " + "transfer size (%d)\n", + sg->length); + host->flags &= ~SDHCI_REQ_USE_DMA; + break; + } + } + } } /* * The assumption here being that alignment is the same after * translation to device address space. */ - if (unlikely((host->flags & SDHCI_REQ_USE_DMA) && - (host->quirks & SDHCI_QUIRK_32BIT_DMA_ADDR) && - (data->sg->offset & 0x3))) { - DBG("Reverting to PIO because of bad alignment\n"); - host->flags &= ~SDHCI_REQ_USE_DMA; + if (host->flags & SDHCI_REQ_USE_DMA) { + int broken, i; + struct scatterlist *sg; + + broken = 0; + if (host->flags & SDHCI_USE_ADMA) { + /* + * As we use 3 byte chunks to work around + * alignment problems, we need to check this + * quirk. + */ + if (host->quirks & SDHCI_QUIRK_32BIT_ADMA_SIZE) + broken = 1; + } else { + if (host->quirks & SDHCI_QUIRK_32BIT_DMA_ADDR) + broken = 1; + } + + if (unlikely(broken)) { + for_each_sg(data->sg, sg, data->sg_len, i) { + if (sg->offset & 0x3) { + DBG("Reverting to PIO because of " + "bad alignment\n"); + host->flags &= ~SDHCI_REQ_USE_DMA; + break; + } + } + } + } + + /* + * Always adjust the DMA selection as some controllers + * (e.g. JMicron) can't do PIO properly when the selection + * is ADMA. + */ + if (host->version >= SDHCI_SPEC_200) { + ctrl = readb(host->ioaddr + SDHCI_HOST_CONTROL); + ctrl &= ~SDHCI_CTRL_DMA_MASK; + if ((host->flags & SDHCI_REQ_USE_DMA) && + (host->flags & SDHCI_USE_ADMA)) + ctrl |= SDHCI_CTRL_ADMA32; + else + ctrl |= SDHCI_CTRL_SDMA; + writeb(ctrl, host->ioaddr + SDHCI_HOST_CONTROL); } if (host->flags & SDHCI_REQ_USE_DMA) { - int count; + if (host->flags & SDHCI_USE_ADMA) { + sdhci_adma_table_pre(host, data); + writel(host->adma_addr, + host->ioaddr + SDHCI_ADMA_ADDRESS); + } else { + int count; - count = dma_map_sg(mmc_dev(host->mmc), data->sg, data->sg_len, - (data->flags & MMC_DATA_READ) ? - DMA_FROM_DEVICE : DMA_TO_DEVICE); - WARN_ON(count != 1); + count = dma_map_sg(mmc_dev(host->mmc), + data->sg, data->sg_len, + (data->flags & MMC_DATA_READ) ? + DMA_FROM_DEVICE : + DMA_TO_DEVICE); + WARN_ON(count != 1); - writel(sg_dma_address(data->sg), - host->ioaddr + SDHCI_DMA_ADDRESS); + writel(sg_dma_address(data->sg), + host->ioaddr + SDHCI_DMA_ADDRESS); + } } else { host->cur_sg = data->sg; host->num_sg = data->sg_len; @@ -457,9 +718,13 @@ static void sdhci_finish_data(struct sdhci_host *host) host->data = NULL; if (host->flags & SDHCI_REQ_USE_DMA) { - dma_unmap_sg(mmc_dev(host->mmc), data->sg, data->sg_len, - (data->flags & MMC_DATA_READ) ? - DMA_FROM_DEVICE : DMA_TO_DEVICE); + if (host->flags & SDHCI_USE_ADMA) + sdhci_adma_table_post(host, data); + else { + dma_unmap_sg(mmc_dev(host->mmc), data->sg, + data->sg_len, (data->flags & MMC_DATA_READ) ? + DMA_FROM_DEVICE : DMA_TO_DEVICE); + } } /* @@ -1008,6 +1273,8 @@ static void sdhci_data_irq(struct sdhci_host *host, u32 intmask) host->data->error = -ETIMEDOUT; else if (intmask & (SDHCI_INT_DATA_CRC | SDHCI_INT_DATA_END_BIT)) host->data->error = -EILSEQ; + else if (intmask & SDHCI_INT_ADMA_ERROR) + host->data->error = -EIO; if (host->data->error) sdhci_finish_data(host); @@ -1199,7 +1466,6 @@ int sdhci_add_host(struct sdhci_host *host) { struct mmc_host *mmc; unsigned int caps; - unsigned int version; int ret; WARN_ON(host == NULL); @@ -1213,12 +1479,13 @@ int sdhci_add_host(struct sdhci_host *host) sdhci_reset(host, SDHCI_RESET_ALL); - version = readw(host->ioaddr + SDHCI_HOST_VERSION); - version = (version & SDHCI_SPEC_VER_MASK) >> SDHCI_SPEC_VER_SHIFT; - if (version > 1) { + host->version = readw(host->ioaddr + SDHCI_HOST_VERSION); + host->version = (host->version & SDHCI_SPEC_VER_MASK) + >> SDHCI_SPEC_VER_SHIFT; + if (host->version > SDHCI_SPEC_200) { printk(KERN_ERR "%s: Unknown controller version (%d). " "You may experience problems.\n", mmc_hostname(mmc), - version); + host->version); } caps = readl(host->ioaddr + SDHCI_CAPABILITIES); @@ -1236,17 +1503,47 @@ int sdhci_add_host(struct sdhci_host *host) host->flags &= ~SDHCI_USE_DMA; } + if (host->flags & SDHCI_USE_DMA) { + if ((host->version >= SDHCI_SPEC_200) && + (caps & SDHCI_CAN_DO_ADMA2)) + host->flags |= SDHCI_USE_ADMA; + } + + if ((host->quirks & SDHCI_QUIRK_BROKEN_ADMA) && + (host->flags & SDHCI_USE_ADMA)) { + DBG("Disabling ADMA as it is marked broken\n"); + host->flags &= ~SDHCI_USE_ADMA; + } + if (host->flags & SDHCI_USE_DMA) { if (host->ops->enable_dma) { if (host->ops->enable_dma(host)) { printk(KERN_WARNING "%s: No suitable DMA " "available. Falling back to PIO.\n", mmc_hostname(mmc)); - host->flags &= ~SDHCI_USE_DMA; + host->flags &= ~(SDHCI_USE_DMA | SDHCI_USE_ADMA); } } } + if (host->flags & SDHCI_USE_ADMA) { + /* + * We need to allocate descriptors for all sg entries + * (128) and potentially one alignment transfer for + * each of those entries. + */ + host->adma_desc = kmalloc((128 * 2 + 1) * 4, GFP_KERNEL); + host->align_buffer = kmalloc(128 * 4, GFP_KERNEL); + if (!host->adma_desc || !host->align_buffer) { + kfree(host->adma_desc); + kfree(host->align_buffer); + printk(KERN_WARNING "%s: Unable to allocate ADMA " + "buffers. Falling back to standard DMA.\n", + mmc_hostname(mmc)); + host->flags &= ~SDHCI_USE_ADMA; + } + } + /* XXX: Hack to get MMC layer to avoid highmem */ if (!(host->flags & SDHCI_USE_DMA)) mmc_dev(host->mmc)->dma_mask = 0; @@ -1298,13 +1595,16 @@ int sdhci_add_host(struct sdhci_host *host) spin_lock_init(&host->lock); /* - * Maximum number of segments. Hardware cannot do scatter lists. + * Maximum number of segments. Depends on if the hardware + * can do scatter/gather or not. */ - if (host->flags & SDHCI_USE_DMA) + if (host->flags & SDHCI_USE_ADMA) + mmc->max_hw_segs = 128; + else if (host->flags & SDHCI_USE_DMA) mmc->max_hw_segs = 1; - else - mmc->max_hw_segs = 16; - mmc->max_phys_segs = 16; + else /* PIO */ + mmc->max_hw_segs = 128; + mmc->max_phys_segs = 128; /* * Maximum number of sectors in one transfer. Limited by DMA boundary @@ -1314,9 +1614,13 @@ int sdhci_add_host(struct sdhci_host *host) /* * Maximum segment size. Could be one segment with the maximum number - * of bytes. + * of bytes. When doing hardware scatter/gather, each entry cannot + * be larger than 64 KiB though. */ - mmc->max_seg_size = mmc->max_req_size; + if (host->flags & SDHCI_USE_ADMA) + mmc->max_seg_size = 65536; + else + mmc->max_seg_size = mmc->max_req_size; /* * Maximum block size. This varies from controller to controller and @@ -1371,8 +1675,9 @@ int sdhci_add_host(struct sdhci_host *host) mmc_add_host(mmc); - printk(KERN_INFO "%s: SDHCI controller on %s [%s] using %s\n", + printk(KERN_INFO "%s: SDHCI controller on %s [%s] using %s%s\n", mmc_hostname(mmc), host->hw_name, mmc_dev(mmc)->bus_id, + (host->flags & SDHCI_USE_ADMA)?"A":"", (host->flags & SDHCI_USE_DMA)?"DMA":"PIO"); return 0; @@ -1426,6 +1731,12 @@ void sdhci_remove_host(struct sdhci_host *host, int dead) tasklet_kill(&host->card_tasklet); tasklet_kill(&host->finish_tasklet); + + kfree(host->adma_desc); + kfree(host->align_buffer); + + host->adma_desc = NULL; + host->align_buffer = NULL; } EXPORT_SYMBOL_GPL(sdhci_remove_host); diff --git a/drivers/mmc/host/sdhci.h b/drivers/mmc/host/sdhci.h index 7c302515a6a..5bb35528176 100644 --- a/drivers/mmc/host/sdhci.h +++ b/drivers/mmc/host/sdhci.h @@ -60,6 +60,11 @@ #define SDHCI_CTRL_LED 0x01 #define SDHCI_CTRL_4BITBUS 0x02 #define SDHCI_CTRL_HISPD 0x04 +#define SDHCI_CTRL_DMA_MASK 0x18 +#define SDHCI_CTRL_SDMA 0x00 +#define SDHCI_CTRL_ADMA1 0x08 +#define SDHCI_CTRL_ADMA32 0x10 +#define SDHCI_CTRL_ADMA64 0x18 #define SDHCI_POWER_CONTROL 0x29 #define SDHCI_POWER_ON 0x01 @@ -105,6 +110,7 @@ #define SDHCI_INT_DATA_END_BIT 0x00400000 #define SDHCI_INT_BUS_POWER 0x00800000 #define SDHCI_INT_ACMD12ERR 0x01000000 +#define SDHCI_INT_ADMA_ERROR 0x02000000 #define SDHCI_INT_NORMAL_MASK 0x00007FFF #define SDHCI_INT_ERROR_MASK 0xFFFF8000 @@ -128,11 +134,14 @@ #define SDHCI_CLOCK_BASE_SHIFT 8 #define SDHCI_MAX_BLOCK_MASK 0x00030000 #define SDHCI_MAX_BLOCK_SHIFT 16 +#define SDHCI_CAN_DO_ADMA2 0x00080000 +#define SDHCI_CAN_DO_ADMA1 0x00100000 #define SDHCI_CAN_DO_HISPD 0x00200000 #define SDHCI_CAN_DO_DMA 0x00400000 #define SDHCI_CAN_VDD_330 0x01000000 #define SDHCI_CAN_VDD_300 0x02000000 #define SDHCI_CAN_VDD_180 0x04000000 +#define SDHCI_CAN_64BIT 0x10000000 /* 44-47 reserved for more caps */ @@ -140,7 +149,16 @@ /* 4C-4F reserved for more max current */ -/* 50-FB reserved */ +#define SDHCI_SET_ACMD12_ERROR 0x50 +#define SDHCI_SET_INT_ERROR 0x52 + +#define SDHCI_ADMA_ERROR 0x54 + +/* 55-57 reserved */ + +#define SDHCI_ADMA_ADDRESS 0x58 + +/* 60-FB reserved */ #define SDHCI_SLOT_INT_STATUS 0xFC @@ -149,6 +167,8 @@ #define SDHCI_VENDOR_VER_SHIFT 8 #define SDHCI_SPEC_VER_MASK 0x00FF #define SDHCI_SPEC_VER_SHIFT 0 +#define SDHCI_SPEC_100 0 +#define SDHCI_SPEC_200 1 struct sdhci_ops; @@ -170,16 +190,20 @@ struct sdhci_host { #define SDHCI_QUIRK_RESET_CMD_DATA_ON_IOS (1<<4) /* Controller has an unusable DMA engine */ #define SDHCI_QUIRK_BROKEN_DMA (1<<5) +/* Controller has an unusable ADMA engine */ +#define SDHCI_QUIRK_BROKEN_ADMA (1<<6) /* Controller can only DMA from 32-bit aligned addresses */ -#define SDHCI_QUIRK_32BIT_DMA_ADDR (1<<6) +#define SDHCI_QUIRK_32BIT_DMA_ADDR (1<<7) /* Controller can only DMA chunk sizes that are a multiple of 32 bits */ -#define SDHCI_QUIRK_32BIT_DMA_SIZE (1<<7) +#define SDHCI_QUIRK_32BIT_DMA_SIZE (1<<8) +/* Controller can only ADMA chunks that are a multiple of 32 bits */ +#define SDHCI_QUIRK_32BIT_ADMA_SIZE (1<<9) /* Controller needs to be reset after each request to stay stable */ -#define SDHCI_QUIRK_RESET_AFTER_REQUEST (1<<8) +#define SDHCI_QUIRK_RESET_AFTER_REQUEST (1<<10) /* Controller needs voltage and power writes to happen separately */ -#define SDHCI_QUIRK_NO_SIMULT_VDD_AND_POWER (1<<9) +#define SDHCI_QUIRK_NO_SIMULT_VDD_AND_POWER (1<<11) /* Controller provides an incorrect timeout value for transfers */ -#define SDHCI_QUIRK_BROKEN_TIMEOUT_VAL (1<<10) +#define SDHCI_QUIRK_BROKEN_TIMEOUT_VAL (1<<12) int irq; /* Device IRQ */ void __iomem * ioaddr; /* Mapped address */ @@ -197,8 +221,11 @@ struct sdhci_host { int flags; /* Host attributes */ #define SDHCI_USE_DMA (1<<0) /* Host is DMA capable */ -#define SDHCI_REQ_USE_DMA (1<<1) /* Use DMA for this req. */ -#define SDHCI_DEVICE_DEAD (1<<2) /* Device unresponsive */ +#define SDHCI_USE_ADMA (1<<1) /* Host is ADMA capable */ +#define SDHCI_REQ_USE_DMA (1<<2) /* Use DMA for this req. */ +#define SDHCI_DEVICE_DEAD (1<<3) /* Device unresponsive */ + + unsigned int version; /* SDHCI spec. version */ unsigned int max_clk; /* Max possible freq (MHz) */ unsigned int timeout_clk; /* Timeout freq (KHz) */ @@ -216,6 +243,14 @@ struct sdhci_host { int offset; /* Offset into current sg */ int remain; /* Bytes left in current */ + int sg_count; /* Mapped sg entries */ + + u8 *adma_desc; /* ADMA descriptor table */ + u8 *align_buffer; /* Bounce buffer */ + + dma_addr_t adma_addr; /* Mapped ADMA descr. table */ + dma_addr_t align_addr; /* Mapped bounce buffer */ + struct tasklet_struct card_tasklet; /* Tasklet structures */ struct tasklet_struct finish_tasklet; -- 2.20.1