From 171e23e150acfb285f1772cedf04d35694af740b Mon Sep 17 00:00:00 2001 From: Jarkko Nikula Date: Thu, 29 Sep 2016 16:04:59 +0300 Subject: [PATCH] i2c: designware: Avoid aborted transfers with fast reacting I2C slaves I2C DesignWare may abort transfer with arbitration lost if I2C slave pulls SDA down quickly after falling edge of SCL. Reason for this is unknown but after trial and error it was found this can be avoided by enabling non-zero SDA RX hold time for the receiver. By the specification SDA RX hold time extends incoming SDA low to high transition by n * ic_clk cycles but only when SCL is high. However it seems to help avoid above faulty arbitration lost error. Bits 23:16 in IC_SDA_HOLD register define the SDA RX hold time for the receiver. Be conservative and enable 1 ic_clk cycle long hold time in case boot firmware hasn't set it up. Reported-by: Jukka Laitinen Signed-off-by: Jarkko Nikula Tested-by: Jukka Laitinen Signed-off-by: Wolfram Sang --- drivers/i2c/busses/i2c-designware-core.c | 17 ++++++++++++++--- 1 file changed, 14 insertions(+), 3 deletions(-) diff --git a/drivers/i2c/busses/i2c-designware-core.c b/drivers/i2c/busses/i2c-designware-core.c index 1fe93c43215c..11e866d05368 100644 --- a/drivers/i2c/busses/i2c-designware-core.c +++ b/drivers/i2c/busses/i2c-designware-core.c @@ -95,6 +95,9 @@ #define DW_IC_STATUS_TFE BIT(2) #define DW_IC_STATUS_MST_ACTIVITY BIT(5) +#define DW_IC_SDA_HOLD_RX_SHIFT 16 +#define DW_IC_SDA_HOLD_RX_MASK GENMASK(23, DW_IC_SDA_HOLD_RX_SHIFT) + #define DW_IC_ERR_TX_ABRT 0x1 #define DW_IC_TAR_10BITADDR_MASTER BIT(12) @@ -420,12 +423,20 @@ int i2c_dw_init(struct dw_i2c_dev *dev) /* Configure SDA Hold Time if required */ reg = dw_readl(dev, DW_IC_COMP_VERSION); if (reg >= DW_IC_SDA_HOLD_MIN_VERS) { - if (dev->sda_hold_time) { - dw_writel(dev, dev->sda_hold_time, DW_IC_SDA_HOLD); - } else { + if (!dev->sda_hold_time) { /* Keep previous hold time setting if no one set it */ dev->sda_hold_time = dw_readl(dev, DW_IC_SDA_HOLD); } + /* + * Workaround for avoiding TX arbitration lost in case I2C + * slave pulls SDA down "too quickly" after falling egde of + * SCL by enabling non-zero SDA RX hold. Specification says it + * extends incoming SDA low to high transition while SCL is + * high but it apprears to help also above issue. + */ + if (!(dev->sda_hold_time & DW_IC_SDA_HOLD_RX_MASK)) + dev->sda_hold_time |= 1 << DW_IC_SDA_HOLD_RX_SHIFT; + dw_writel(dev, dev->sda_hold_time, DW_IC_SDA_HOLD); } else { dev_warn(dev->dev, "Hardware too old to adjust SDA hold time.\n"); -- 2.20.1