From 12f188f2e59394ec1f1c8c0a4439f48ec16bc336 Mon Sep 17 00:00:00 2001 From: Dan Williams Date: Sun, 19 Dec 2010 08:17:50 +0000 Subject: [PATCH] ueagle-atm: fix PHY signal initialization race A race exists when initializing ueagle-atm devices where the generic atm device may not yet be created before the driver attempts to initialize it's PHY signal state, which checks whether the atm device has been created or not. This often causes the sysfs 'carrier' attribute to be '1' even though no signal has actually been found. uea_probe usbatm_usb_probe driver->bind (uea_bind) uea_boot kthread_run(uea_kthread) uea_kthread usbatm_atm_init uea_start_reset atm_dev_register UPDATE_ATM_SIGNAL UPDATE_ATM_SIGNAL checks whether the ATM device has been created and if not, will not update the PHY signal state. Because of the race that does not always happen in time, and the PHY signal state remains ATM_PHY_SIG_FOUND even though no signal exists. To fix the race, just create the kthread during initialization, and only after initialization is complete, start the thread that reboots the device and initializes PHY state. [ 3030.490931] uea_probe: calling usbatm_usb_probe [ 3030.490946] ueagle-atm 8-2:1.0: usbatm_usb_probe: trying driver ueagle-atm with vendor=1110, product=9031, ifnum 0 [ 3030.493691] uea_bind: setting usbatm [ 3030.496932] usb 8-2: [ueagle-atm] using iso mode [ 3030.497283] ueagle-atm 8-2:1.0: usbatm_usb_probe: using 3021 byte buffer for rx channel 0xffff880125953508 [ 3030.497292] usb 8-2: [ueagle-atm] (re)booting started [ 3030.497298] uea_start_reset: atm dev (null) [ 3030.497306] ueagle-atm 8-2:1.0: usbatm_usb_probe: using 3392 byte buffer for tx channel 0xffff8801259535b8 [ 3030.497374] usbatm_usb_probe: about to init [ 3030.497379] usbatm_usb_probe: calling usbatm_atm_init [ 3030.497384] usbatm_atm_init: creating atm device! Signed-off-by: Dan Williams Signed-off-by: David S. Miller --- drivers/usb/atm/ueagle-atm.c | 22 +++++++++++++++++++--- 1 file changed, 19 insertions(+), 3 deletions(-) diff --git a/drivers/usb/atm/ueagle-atm.c b/drivers/usb/atm/ueagle-atm.c index 44447f54942f..99ac70e32556 100644 --- a/drivers/usb/atm/ueagle-atm.c +++ b/drivers/usb/atm/ueagle-atm.c @@ -2206,8 +2206,11 @@ static int uea_boot(struct uea_softc *sc) goto err1; } - sc->kthread = kthread_run(uea_kthread, sc, "ueagle-atm"); - if (sc->kthread == ERR_PTR(-ENOMEM)) { + /* Create worker thread, but don't start it here. Start it after + * all usbatm generic initialization is done. + */ + sc->kthread = kthread_create(uea_kthread, sc, "ueagle-atm"); + if (IS_ERR(sc->kthread)) { uea_err(INS_TO_USBDEV(sc), "failed to create thread\n"); goto err2; } @@ -2624,6 +2627,7 @@ static struct usbatm_driver uea_usbatm_driver = { static int uea_probe(struct usb_interface *intf, const struct usb_device_id *id) { struct usb_device *usb = interface_to_usbdev(intf); + int ret; uea_enters(usb); uea_info(usb, "ADSL device founded vid (%#X) pid (%#X) Rev (%#X): %s\n", @@ -2637,7 +2641,19 @@ static int uea_probe(struct usb_interface *intf, const struct usb_device_id *id) if (UEA_IS_PREFIRM(id)) return uea_load_firmware(usb, UEA_CHIP_VERSION(id)); - return usbatm_usb_probe(intf, id, &uea_usbatm_driver); + ret = usbatm_usb_probe(intf, id, &uea_usbatm_driver); + if (ret == 0) { + struct usbatm_data *usbatm = usb_get_intfdata(intf); + struct uea_softc *sc = usbatm->driver_data; + + /* Ensure carrier is initialized to off as early as possible */ + UPDATE_ATM_SIGNAL(ATM_PHY_SIG_LOST); + + /* Only start the worker thread when all init is done */ + wake_up_process(sc->kthread); + } + + return ret; } static void uea_disconnect(struct usb_interface *intf) -- 2.20.1