From 0b0c2b31bdf8d6fb5c14ae70894453ac44d64672 Mon Sep 17 00:00:00 2001 From: Emil Tantilov Date: Sat, 26 Feb 2011 06:40:16 +0000 Subject: [PATCH] ixgbe: Enable flow control pause parameter auto-negotiation support This patch enables flow control pause parameters auto-negotiation support to 82599 based 10G Base-T, backplane devices and multi-speed fiber optics modules at 1G speed Signed-off-by: Emil Tantilov Tested-by: Stephen Ko Signed-off-by: Jeff Kirsher --- drivers/net/ixgbe/ixgbe_82598.c | 7 +- drivers/net/ixgbe/ixgbe_82599.c | 3 + drivers/net/ixgbe/ixgbe_common.c | 460 ++++++++++++++++++------------- drivers/net/ixgbe/ixgbe_main.c | 3 +- drivers/net/ixgbe/ixgbe_phy.h | 4 + drivers/net/ixgbe/ixgbe_type.h | 3 + 6 files changed, 281 insertions(+), 199 deletions(-) diff --git a/drivers/net/ixgbe/ixgbe_82598.c b/drivers/net/ixgbe/ixgbe_82598.c index dc977b1c8eab..ff23907bde0c 100644 --- a/drivers/net/ixgbe/ixgbe_82598.c +++ b/drivers/net/ixgbe/ixgbe_82598.c @@ -366,7 +366,7 @@ static s32 ixgbe_fc_enable_82598(struct ixgbe_hw *hw, s32 packetbuf_num) /* Negotiate the fc mode to use */ ret_val = ixgbe_fc_autoneg(hw); - if (ret_val) + if (ret_val == IXGBE_ERR_FLOW_CONTROL) goto out; /* Disable any previous flow control settings */ @@ -384,10 +384,10 @@ static s32 ixgbe_fc_enable_82598(struct ixgbe_hw *hw, s32 packetbuf_num) * 2: Tx flow control is enabled (we can send pause frames but * we do not support receiving pause frames). * 3: Both Rx and Tx flow control (symmetric) are enabled. - * other: Invalid. #ifdef CONFIG_DCB * 4: Priority Flow Control is enabled. #endif + * other: Invalid. */ switch (hw->fc.current_mode) { case ixgbe_fc_none: @@ -444,9 +444,10 @@ static s32 ixgbe_fc_enable_82598(struct ixgbe_hw *hw, s32 packetbuf_num) reg = (rx_pba_size - hw->fc.low_water) << 6; if (hw->fc.send_xon) reg |= IXGBE_FCRTL_XONE; + IXGBE_WRITE_REG(hw, IXGBE_FCRTL(packetbuf_num), reg); - reg = (rx_pba_size - hw->fc.high_water) << 10; + reg = (rx_pba_size - hw->fc.high_water) << 6; reg |= IXGBE_FCRTH_FCEN; IXGBE_WRITE_REG(hw, IXGBE_FCRTH(packetbuf_num), reg); diff --git a/drivers/net/ixgbe/ixgbe_82599.c b/drivers/net/ixgbe/ixgbe_82599.c index 2f8b9f41714f..00aeba385a2f 100644 --- a/drivers/net/ixgbe/ixgbe_82599.c +++ b/drivers/net/ixgbe/ixgbe_82599.c @@ -772,6 +772,9 @@ static s32 ixgbe_setup_mac_link_82599(struct ixgbe_hw *hw, /* Check to see if speed passed in is supported. */ hw->mac.ops.get_link_capabilities(hw, &link_capabilities, &autoneg); + if (status != 0) + goto out; + speed &= link_capabilities; if (speed == IXGBE_LINK_SPEED_UNKNOWN) { diff --git a/drivers/net/ixgbe/ixgbe_common.c b/drivers/net/ixgbe/ixgbe_common.c index 561f666618e4..7a6a3fbee19f 100644 --- a/drivers/net/ixgbe/ixgbe_common.c +++ b/drivers/net/ixgbe/ixgbe_common.c @@ -47,6 +47,12 @@ static void ixgbe_lower_eeprom_clk(struct ixgbe_hw *hw, u32 *eec); static void ixgbe_release_eeprom(struct ixgbe_hw *hw); static s32 ixgbe_mta_vector(struct ixgbe_hw *hw, u8 *mc_addr); +static s32 ixgbe_fc_autoneg_fiber(struct ixgbe_hw *hw); +static s32 ixgbe_fc_autoneg_backplane(struct ixgbe_hw *hw); +static s32 ixgbe_fc_autoneg_copper(struct ixgbe_hw *hw); +static s32 ixgbe_device_supports_autoneg_fc(struct ixgbe_hw *hw); +static s32 ixgbe_negotiate_fc(struct ixgbe_hw *hw, u32 adv_reg, u32 lp_reg, + u32 adv_sym, u32 adv_asm, u32 lp_sym, u32 lp_asm); static s32 ixgbe_setup_fc(struct ixgbe_hw *hw, s32 packetbuf_num); /** @@ -1566,7 +1572,7 @@ s32 ixgbe_fc_enable_generic(struct ixgbe_hw *hw, s32 packetbuf_num) #endif /* CONFIG_DCB */ /* Negotiate the fc mode to use */ ret_val = ixgbe_fc_autoneg(hw); - if (ret_val) + if (ret_val == IXGBE_ERR_FLOW_CONTROL) goto out; /* Disable any previous flow control settings */ @@ -1674,12 +1680,13 @@ out: **/ s32 ixgbe_fc_autoneg(struct ixgbe_hw *hw) { - s32 ret_val = 0; + s32 ret_val = IXGBE_ERR_FC_NOT_NEGOTIATED; ixgbe_link_speed speed; - u32 pcs_anadv_reg, pcs_lpab_reg, linkstat; - u32 links2, anlp1_reg, autoc_reg, links; bool link_up; + if (hw->fc.disable_fc_autoneg) + goto out; + /* * AN should have completed when the cable was plugged in. * Look for reasons to bail out. Bail out if: @@ -1690,153 +1697,199 @@ s32 ixgbe_fc_autoneg(struct ixgbe_hw *hw) * So use link_up_wait_to_complete=false. */ hw->mac.ops.check_link(hw, &speed, &link_up, false); - - if (hw->fc.disable_fc_autoneg || (!link_up)) { - hw->fc.fc_was_autonegged = false; - hw->fc.current_mode = hw->fc.requested_mode; + if (!link_up) { + ret_val = IXGBE_ERR_FLOW_CONTROL; goto out; } - /* - * On backplane, bail out if - * - backplane autoneg was not completed, or if - * - we are 82599 and link partner is not AN enabled - */ - if (hw->phy.media_type == ixgbe_media_type_backplane) { - links = IXGBE_READ_REG(hw, IXGBE_LINKS); - if ((links & IXGBE_LINKS_KX_AN_COMP) == 0) { - hw->fc.fc_was_autonegged = false; - hw->fc.current_mode = hw->fc.requested_mode; - goto out; - } + switch (hw->phy.media_type) { + /* Autoneg flow control on fiber adapters */ + case ixgbe_media_type_fiber: + if (speed == IXGBE_LINK_SPEED_1GB_FULL) + ret_val = ixgbe_fc_autoneg_fiber(hw); + break; - if (hw->mac.type == ixgbe_mac_82599EB) { - links2 = IXGBE_READ_REG(hw, IXGBE_LINKS2); - if ((links2 & IXGBE_LINKS2_AN_SUPPORTED) == 0) { - hw->fc.fc_was_autonegged = false; - hw->fc.current_mode = hw->fc.requested_mode; - goto out; - } - } + /* Autoneg flow control on backplane adapters */ + case ixgbe_media_type_backplane: + ret_val = ixgbe_fc_autoneg_backplane(hw); + break; + + /* Autoneg flow control on copper adapters */ + case ixgbe_media_type_copper: + if (ixgbe_device_supports_autoneg_fc(hw) == 0) + ret_val = ixgbe_fc_autoneg_copper(hw); + break; + + default: + break; + } + +out: + if (ret_val == 0) { + hw->fc.fc_was_autonegged = true; + } else { + hw->fc.fc_was_autonegged = false; + hw->fc.current_mode = hw->fc.requested_mode; } + return ret_val; +} + +/** + * ixgbe_fc_autoneg_fiber - Enable flow control on 1 gig fiber + * @hw: pointer to hardware structure + * + * Enable flow control according on 1 gig fiber. + **/ +static s32 ixgbe_fc_autoneg_fiber(struct ixgbe_hw *hw) +{ + u32 pcs_anadv_reg, pcs_lpab_reg, linkstat; + s32 ret_val; /* * On multispeed fiber at 1g, bail out if * - link is up but AN did not complete, or if * - link is up and AN completed but timed out */ - if (hw->phy.multispeed_fiber && (speed == IXGBE_LINK_SPEED_1GB_FULL)) { - linkstat = IXGBE_READ_REG(hw, IXGBE_PCS1GLSTA); - if (((linkstat & IXGBE_PCS1GLSTA_AN_COMPLETE) == 0) || - ((linkstat & IXGBE_PCS1GLSTA_AN_TIMED_OUT) == 1)) { - hw->fc.fc_was_autonegged = false; - hw->fc.current_mode = hw->fc.requested_mode; - goto out; - } + + linkstat = IXGBE_READ_REG(hw, IXGBE_PCS1GLSTA); + if (((linkstat & IXGBE_PCS1GLSTA_AN_COMPLETE) == 0) || + ((linkstat & IXGBE_PCS1GLSTA_AN_TIMED_OUT) == 1)) { + ret_val = IXGBE_ERR_FC_NOT_NEGOTIATED; + goto out; } + pcs_anadv_reg = IXGBE_READ_REG(hw, IXGBE_PCS1GANA); + pcs_lpab_reg = IXGBE_READ_REG(hw, IXGBE_PCS1GANLP); + + ret_val = ixgbe_negotiate_fc(hw, pcs_anadv_reg, + pcs_lpab_reg, IXGBE_PCS1GANA_SYM_PAUSE, + IXGBE_PCS1GANA_ASM_PAUSE, + IXGBE_PCS1GANA_SYM_PAUSE, + IXGBE_PCS1GANA_ASM_PAUSE); + +out: + return ret_val; +} + +/** + * ixgbe_fc_autoneg_backplane - Enable flow control IEEE clause 37 + * @hw: pointer to hardware structure + * + * Enable flow control according to IEEE clause 37. + **/ +static s32 ixgbe_fc_autoneg_backplane(struct ixgbe_hw *hw) +{ + u32 links2, anlp1_reg, autoc_reg, links; + s32 ret_val; + /* - * Bail out on - * - copper or CX4 adapters - * - fiber adapters running at 10gig + * On backplane, bail out if + * - backplane autoneg was not completed, or if + * - we are 82599 and link partner is not AN enabled */ - if ((hw->phy.media_type == ixgbe_media_type_copper) || - (hw->phy.media_type == ixgbe_media_type_cx4) || - ((hw->phy.media_type == ixgbe_media_type_fiber) && - (speed == IXGBE_LINK_SPEED_10GB_FULL))) { + links = IXGBE_READ_REG(hw, IXGBE_LINKS); + if ((links & IXGBE_LINKS_KX_AN_COMP) == 0) { hw->fc.fc_was_autonegged = false; hw->fc.current_mode = hw->fc.requested_mode; + ret_val = IXGBE_ERR_FC_NOT_NEGOTIATED; goto out; } + if (hw->mac.type == ixgbe_mac_82599EB) { + links2 = IXGBE_READ_REG(hw, IXGBE_LINKS2); + if ((links2 & IXGBE_LINKS2_AN_SUPPORTED) == 0) { + hw->fc.fc_was_autonegged = false; + hw->fc.current_mode = hw->fc.requested_mode; + ret_val = IXGBE_ERR_FC_NOT_NEGOTIATED; + goto out; + } + } /* - * Read the AN advertisement and LP ability registers and resolve + * Read the 10g AN autoc and LP ability registers and resolve * local flow control settings accordingly */ - if ((speed == IXGBE_LINK_SPEED_1GB_FULL) && - (hw->phy.media_type != ixgbe_media_type_backplane)) { - pcs_anadv_reg = IXGBE_READ_REG(hw, IXGBE_PCS1GANA); - pcs_lpab_reg = IXGBE_READ_REG(hw, IXGBE_PCS1GANLP); - if ((pcs_anadv_reg & IXGBE_PCS1GANA_SYM_PAUSE) && - (pcs_lpab_reg & IXGBE_PCS1GANA_SYM_PAUSE)) { - /* - * Now we need to check if the user selected Rx ONLY - * of pause frames. In this case, we had to advertise - * FULL flow control because we could not advertise RX - * ONLY. Hence, we must now check to see if we need to - * turn OFF the TRANSMISSION of PAUSE frames. - */ - if (hw->fc.requested_mode == ixgbe_fc_full) { - hw->fc.current_mode = ixgbe_fc_full; - hw_dbg(hw, "Flow Control = FULL.\n"); - } else { - hw->fc.current_mode = ixgbe_fc_rx_pause; - hw_dbg(hw, "Flow Control=RX PAUSE only\n"); - } - } else if (!(pcs_anadv_reg & IXGBE_PCS1GANA_SYM_PAUSE) && - (pcs_anadv_reg & IXGBE_PCS1GANA_ASM_PAUSE) && - (pcs_lpab_reg & IXGBE_PCS1GANA_SYM_PAUSE) && - (pcs_lpab_reg & IXGBE_PCS1GANA_ASM_PAUSE)) { - hw->fc.current_mode = ixgbe_fc_tx_pause; - hw_dbg(hw, "Flow Control = TX PAUSE frames only.\n"); - } else if ((pcs_anadv_reg & IXGBE_PCS1GANA_SYM_PAUSE) && - (pcs_anadv_reg & IXGBE_PCS1GANA_ASM_PAUSE) && - !(pcs_lpab_reg & IXGBE_PCS1GANA_SYM_PAUSE) && - (pcs_lpab_reg & IXGBE_PCS1GANA_ASM_PAUSE)) { - hw->fc.current_mode = ixgbe_fc_rx_pause; - hw_dbg(hw, "Flow Control = RX PAUSE frames only.\n"); - } else { - hw->fc.current_mode = ixgbe_fc_none; - hw_dbg(hw, "Flow Control = NONE.\n"); - } - } + autoc_reg = IXGBE_READ_REG(hw, IXGBE_AUTOC); + anlp1_reg = IXGBE_READ_REG(hw, IXGBE_ANLP1); - if (hw->phy.media_type == ixgbe_media_type_backplane) { + ret_val = ixgbe_negotiate_fc(hw, autoc_reg, + anlp1_reg, IXGBE_AUTOC_SYM_PAUSE, IXGBE_AUTOC_ASM_PAUSE, + IXGBE_ANLP1_SYM_PAUSE, IXGBE_ANLP1_ASM_PAUSE); + +out: + return ret_val; +} + +/** + * ixgbe_fc_autoneg_copper - Enable flow control IEEE clause 37 + * @hw: pointer to hardware structure + * + * Enable flow control according to IEEE clause 37. + **/ +static s32 ixgbe_fc_autoneg_copper(struct ixgbe_hw *hw) +{ + u16 technology_ability_reg = 0; + u16 lp_technology_ability_reg = 0; + + hw->phy.ops.read_reg(hw, MDIO_AN_ADVERTISE, + MDIO_MMD_AN, + &technology_ability_reg); + hw->phy.ops.read_reg(hw, MDIO_AN_LPA, + MDIO_MMD_AN, + &lp_technology_ability_reg); + + return ixgbe_negotiate_fc(hw, (u32)technology_ability_reg, + (u32)lp_technology_ability_reg, + IXGBE_TAF_SYM_PAUSE, IXGBE_TAF_ASM_PAUSE, + IXGBE_TAF_SYM_PAUSE, IXGBE_TAF_ASM_PAUSE); +} + +/** + * ixgbe_negotiate_fc - Negotiate flow control + * @hw: pointer to hardware structure + * @adv_reg: flow control advertised settings + * @lp_reg: link partner's flow control settings + * @adv_sym: symmetric pause bit in advertisement + * @adv_asm: asymmetric pause bit in advertisement + * @lp_sym: symmetric pause bit in link partner advertisement + * @lp_asm: asymmetric pause bit in link partner advertisement + * + * Find the intersection between advertised settings and link partner's + * advertised settings + **/ +static s32 ixgbe_negotiate_fc(struct ixgbe_hw *hw, u32 adv_reg, u32 lp_reg, + u32 adv_sym, u32 adv_asm, u32 lp_sym, u32 lp_asm) +{ + if ((!(adv_reg)) || (!(lp_reg))) + return IXGBE_ERR_FC_NOT_NEGOTIATED; + + if ((adv_reg & adv_sym) && (lp_reg & lp_sym)) { /* - * Read the 10g AN autoc and LP ability registers and resolve - * local flow control settings accordingly + * Now we need to check if the user selected Rx ONLY + * of pause frames. In this case, we had to advertise + * FULL flow control because we could not advertise RX + * ONLY. Hence, we must now check to see if we need to + * turn OFF the TRANSMISSION of PAUSE frames. */ - autoc_reg = IXGBE_READ_REG(hw, IXGBE_AUTOC); - anlp1_reg = IXGBE_READ_REG(hw, IXGBE_ANLP1); - - if ((autoc_reg & IXGBE_AUTOC_SYM_PAUSE) && - (anlp1_reg & IXGBE_ANLP1_SYM_PAUSE)) { - /* - * Now we need to check if the user selected Rx ONLY - * of pause frames. In this case, we had to advertise - * FULL flow control because we could not advertise RX - * ONLY. Hence, we must now check to see if we need to - * turn OFF the TRANSMISSION of PAUSE frames. - */ - if (hw->fc.requested_mode == ixgbe_fc_full) { - hw->fc.current_mode = ixgbe_fc_full; - hw_dbg(hw, "Flow Control = FULL.\n"); - } else { - hw->fc.current_mode = ixgbe_fc_rx_pause; - hw_dbg(hw, "Flow Control=RX PAUSE only\n"); - } - } else if (!(autoc_reg & IXGBE_AUTOC_SYM_PAUSE) && - (autoc_reg & IXGBE_AUTOC_ASM_PAUSE) && - (anlp1_reg & IXGBE_ANLP1_SYM_PAUSE) && - (anlp1_reg & IXGBE_ANLP1_ASM_PAUSE)) { - hw->fc.current_mode = ixgbe_fc_tx_pause; - hw_dbg(hw, "Flow Control = TX PAUSE frames only.\n"); - } else if ((autoc_reg & IXGBE_AUTOC_SYM_PAUSE) && - (autoc_reg & IXGBE_AUTOC_ASM_PAUSE) && - !(anlp1_reg & IXGBE_ANLP1_SYM_PAUSE) && - (anlp1_reg & IXGBE_ANLP1_ASM_PAUSE)) { - hw->fc.current_mode = ixgbe_fc_rx_pause; - hw_dbg(hw, "Flow Control = RX PAUSE frames only.\n"); + if (hw->fc.requested_mode == ixgbe_fc_full) { + hw->fc.current_mode = ixgbe_fc_full; + hw_dbg(hw, "Flow Control = FULL.\n"); } else { - hw->fc.current_mode = ixgbe_fc_none; - hw_dbg(hw, "Flow Control = NONE.\n"); + hw->fc.current_mode = ixgbe_fc_rx_pause; + hw_dbg(hw, "Flow Control=RX PAUSE frames only\n"); } + } else if (!(adv_reg & adv_sym) && (adv_reg & adv_asm) && + (lp_reg & lp_sym) && (lp_reg & lp_asm)) { + hw->fc.current_mode = ixgbe_fc_tx_pause; + hw_dbg(hw, "Flow Control = TX PAUSE frames only.\n"); + } else if ((adv_reg & adv_sym) && (adv_reg & adv_asm) && + !(lp_reg & lp_sym) && (lp_reg & lp_asm)) { + hw->fc.current_mode = ixgbe_fc_rx_pause; + hw_dbg(hw, "Flow Control = RX PAUSE frames only.\n"); + } else { + hw->fc.current_mode = ixgbe_fc_none; + hw_dbg(hw, "Flow Control = NONE.\n"); } - /* Record that current_mode is the result of a successful autoneg */ - hw->fc.fc_was_autonegged = true; - -out: - return ret_val; + return 0; } /** @@ -1848,7 +1901,8 @@ out: static s32 ixgbe_setup_fc(struct ixgbe_hw *hw, s32 packetbuf_num) { s32 ret_val = 0; - u32 reg; + u32 reg = 0, reg_bp = 0; + u16 reg_cu = 0; #ifdef CONFIG_DCB if (hw->fc.requested_mode == ixgbe_fc_pfc) { @@ -1856,7 +1910,7 @@ static s32 ixgbe_setup_fc(struct ixgbe_hw *hw, s32 packetbuf_num) goto out; } -#endif +#endif /* CONFIG_DCB */ /* Validate the packetbuf configuration */ if (packetbuf_num < 0 || packetbuf_num > 7) { hw_dbg(hw, "Invalid packet buffer number [%d], expected range " @@ -1894,11 +1948,26 @@ static s32 ixgbe_setup_fc(struct ixgbe_hw *hw, s32 packetbuf_num) hw->fc.requested_mode = ixgbe_fc_full; /* - * Set up the 1G flow control advertisement registers so the HW will be - * able to do fc autoneg once the cable is plugged in. If we end up - * using 10g instead, this is harmless. + * Set up the 1G and 10G flow control advertisement registers so the + * HW will be able to do fc autoneg once the cable is plugged in. If + * we link at 10G, the 1G advertisement is harmless and vice versa. */ - reg = IXGBE_READ_REG(hw, IXGBE_PCS1GANA); + + switch (hw->phy.media_type) { + case ixgbe_media_type_fiber: + case ixgbe_media_type_backplane: + reg = IXGBE_READ_REG(hw, IXGBE_PCS1GANA); + reg_bp = IXGBE_READ_REG(hw, IXGBE_AUTOC); + break; + + case ixgbe_media_type_copper: + hw->phy.ops.read_reg(hw, MDIO_AN_ADVERTISE, + MDIO_MMD_AN, ®_cu); + break; + + default: + ; + } /* * The possible values of fc.requested_mode are: @@ -1917,6 +1986,11 @@ static s32 ixgbe_setup_fc(struct ixgbe_hw *hw, s32 packetbuf_num) case ixgbe_fc_none: /* Flow control completely disabled by software override. */ reg &= ~(IXGBE_PCS1GANA_SYM_PAUSE | IXGBE_PCS1GANA_ASM_PAUSE); + if (hw->phy.media_type == ixgbe_media_type_backplane) + reg_bp &= ~(IXGBE_AUTOC_SYM_PAUSE | + IXGBE_AUTOC_ASM_PAUSE); + else if (hw->phy.media_type == ixgbe_media_type_copper) + reg_cu &= ~(IXGBE_TAF_SYM_PAUSE | IXGBE_TAF_ASM_PAUSE); break; case ixgbe_fc_rx_pause: /* @@ -1928,6 +2002,11 @@ static s32 ixgbe_setup_fc(struct ixgbe_hw *hw, s32 packetbuf_num) * disable the adapter's ability to send PAUSE frames. */ reg |= (IXGBE_PCS1GANA_SYM_PAUSE | IXGBE_PCS1GANA_ASM_PAUSE); + if (hw->phy.media_type == ixgbe_media_type_backplane) + reg_bp |= (IXGBE_AUTOC_SYM_PAUSE | + IXGBE_AUTOC_ASM_PAUSE); + else if (hw->phy.media_type == ixgbe_media_type_copper) + reg_cu |= (IXGBE_TAF_SYM_PAUSE | IXGBE_TAF_ASM_PAUSE); break; case ixgbe_fc_tx_pause: /* @@ -1936,10 +2015,22 @@ static s32 ixgbe_setup_fc(struct ixgbe_hw *hw, s32 packetbuf_num) */ reg |= (IXGBE_PCS1GANA_ASM_PAUSE); reg &= ~(IXGBE_PCS1GANA_SYM_PAUSE); + if (hw->phy.media_type == ixgbe_media_type_backplane) { + reg_bp |= (IXGBE_AUTOC_ASM_PAUSE); + reg_bp &= ~(IXGBE_AUTOC_SYM_PAUSE); + } else if (hw->phy.media_type == ixgbe_media_type_copper) { + reg_cu |= (IXGBE_TAF_ASM_PAUSE); + reg_cu &= ~(IXGBE_TAF_SYM_PAUSE); + } break; case ixgbe_fc_full: /* Flow control (both Rx and Tx) is enabled by SW override. */ reg |= (IXGBE_PCS1GANA_SYM_PAUSE | IXGBE_PCS1GANA_ASM_PAUSE); + if (hw->phy.media_type == ixgbe_media_type_backplane) + reg_bp |= (IXGBE_AUTOC_SYM_PAUSE | + IXGBE_AUTOC_ASM_PAUSE); + else if (hw->phy.media_type == ixgbe_media_type_copper) + reg_cu |= (IXGBE_TAF_SYM_PAUSE | IXGBE_TAF_ASM_PAUSE); break; #ifdef CONFIG_DCB case ixgbe_fc_pfc: @@ -1953,80 +2044,37 @@ static s32 ixgbe_setup_fc(struct ixgbe_hw *hw, s32 packetbuf_num) break; } - IXGBE_WRITE_REG(hw, IXGBE_PCS1GANA, reg); - reg = IXGBE_READ_REG(hw, IXGBE_PCS1GLCTL); - - /* Disable AN timeout */ - if (hw->fc.strict_ieee) - reg &= ~IXGBE_PCS1GLCTL_AN_1G_TIMEOUT_EN; + if (hw->mac.type != ixgbe_mac_X540) { + /* + * Enable auto-negotiation between the MAC & PHY; + * the MAC will advertise clause 37 flow control. + */ + IXGBE_WRITE_REG(hw, IXGBE_PCS1GANA, reg); + reg = IXGBE_READ_REG(hw, IXGBE_PCS1GLCTL); - IXGBE_WRITE_REG(hw, IXGBE_PCS1GLCTL, reg); - hw_dbg(hw, "Set up FC; PCS1GLCTL = 0x%08X\n", reg); + /* Disable AN timeout */ + if (hw->fc.strict_ieee) + reg &= ~IXGBE_PCS1GLCTL_AN_1G_TIMEOUT_EN; - /* - * Set up the 10G flow control advertisement registers so the HW - * can do fc autoneg once the cable is plugged in. If we end up - * using 1g instead, this is harmless. - */ - reg = IXGBE_READ_REG(hw, IXGBE_AUTOC); + IXGBE_WRITE_REG(hw, IXGBE_PCS1GLCTL, reg); + hw_dbg(hw, "Set up FC; PCS1GLCTL = 0x%08X\n", reg); + } /* - * The possible values of fc.requested_mode are: - * 0: Flow control is completely disabled - * 1: Rx flow control is enabled (we can receive pause frames, - * but not send pause frames). - * 2: Tx flow control is enabled (we can send pause frames but - * we do not support receiving pause frames). - * 3: Both Rx and Tx flow control (symmetric) are enabled. - * other: Invalid. + * AUTOC restart handles negotiation of 1G and 10G on backplane + * and copper. There is no need to set the PCS1GCTL register. + * */ - switch (hw->fc.requested_mode) { - case ixgbe_fc_none: - /* Flow control completely disabled by software override. */ - reg &= ~(IXGBE_AUTOC_SYM_PAUSE | IXGBE_AUTOC_ASM_PAUSE); - break; - case ixgbe_fc_rx_pause: - /* - * Rx Flow control is enabled and Tx Flow control is - * disabled by software override. Since there really - * isn't a way to advertise that we are capable of RX - * Pause ONLY, we will advertise that we support both - * symmetric and asymmetric Rx PAUSE. Later, we will - * disable the adapter's ability to send PAUSE frames. - */ - reg |= (IXGBE_AUTOC_SYM_PAUSE | IXGBE_AUTOC_ASM_PAUSE); - break; - case ixgbe_fc_tx_pause: - /* - * Tx Flow control is enabled, and Rx Flow control is - * disabled by software override. - */ - reg |= (IXGBE_AUTOC_ASM_PAUSE); - reg &= ~(IXGBE_AUTOC_SYM_PAUSE); - break; - case ixgbe_fc_full: - /* Flow control (both Rx and Tx) is enabled by SW override. */ - reg |= (IXGBE_AUTOC_SYM_PAUSE | IXGBE_AUTOC_ASM_PAUSE); - break; -#ifdef CONFIG_DCB - case ixgbe_fc_pfc: - goto out; - break; -#endif /* CONFIG_DCB */ - default: - hw_dbg(hw, "Flow control param set incorrectly\n"); - ret_val = IXGBE_ERR_CONFIG; - goto out; - break; + if (hw->phy.media_type == ixgbe_media_type_backplane) { + reg_bp |= IXGBE_AUTOC_AN_RESTART; + IXGBE_WRITE_REG(hw, IXGBE_AUTOC, reg_bp); + } else if ((hw->phy.media_type == ixgbe_media_type_copper) && + (ixgbe_device_supports_autoneg_fc(hw) == 0)) { + hw->phy.ops.write_reg(hw, MDIO_AN_ADVERTISE, + MDIO_MMD_AN, reg_cu); } - /* - * AUTOC restart handles negotiation of 1G and 10G. There is - * no need to set the PCS1GCTL register. - */ - reg |= IXGBE_AUTOC_AN_RESTART; - IXGBE_WRITE_REG(hw, IXGBE_AUTOC, reg); - hw_dbg(hw, "Set up FC; IXGBE_AUTOC = 0x%08X\n", reg); + hw_dbg(hw, "Set up FC; IXGBE_AUTOC = 0x%08X\n", reg); out: return ret_val; } @@ -2750,6 +2798,28 @@ wwn_prefix_out: return 0; } +/** + * ixgbe_device_supports_autoneg_fc - Check if phy supports autoneg flow + * control + * @hw: pointer to hardware structure + * + * There are several phys that do not support autoneg flow control. This + * function check the device id to see if the associated phy supports + * autoneg flow control. + **/ +static s32 ixgbe_device_supports_autoneg_fc(struct ixgbe_hw *hw) +{ + + switch (hw->device_id) { + case IXGBE_DEV_ID_X540T: + return 0; + case IXGBE_DEV_ID_82599_T3_LOM: + return 0; + default: + return IXGBE_ERR_FC_NOT_SUPPORTED; + } +} + /** * ixgbe_set_mac_anti_spoofing - Enable/Disable MAC anti-spoofing * @hw: pointer to hardware structure diff --git a/drivers/net/ixgbe/ixgbe_main.c b/drivers/net/ixgbe/ixgbe_main.c index 5e8c39decca1..5998dc94dd5c 100644 --- a/drivers/net/ixgbe/ixgbe_main.c +++ b/drivers/net/ixgbe/ixgbe_main.c @@ -3775,7 +3775,8 @@ static int ixgbe_non_sfp_link_config(struct ixgbe_hw *hw) if (ret) goto link_cfg_out; - if (hw->mac.ops.get_link_capabilities) + autoneg = hw->phy.autoneg_advertised; + if ((!autoneg) && (hw->mac.ops.get_link_capabilities)) ret = hw->mac.ops.get_link_capabilities(hw, &autoneg, &negotiation); if (ret) diff --git a/drivers/net/ixgbe/ixgbe_phy.h b/drivers/net/ixgbe/ixgbe_phy.h index 2327baf04426..9bf2783d7a74 100644 --- a/drivers/net/ixgbe/ixgbe_phy.h +++ b/drivers/net/ixgbe/ixgbe_phy.h @@ -58,6 +58,10 @@ #define IXGBE_I2C_EEPROM_STATUS_FAIL 0x2 #define IXGBE_I2C_EEPROM_STATUS_IN_PROGRESS 0x3 +/* Flow control defines */ +#define IXGBE_TAF_SYM_PAUSE 0x400 +#define IXGBE_TAF_ASM_PAUSE 0x800 + /* Bit-shift macros */ #define IXGBE_SFF_VENDOR_OUI_BYTE0_SHIFT 24 #define IXGBE_SFF_VENDOR_OUI_BYTE1_SHIFT 16 diff --git a/drivers/net/ixgbe/ixgbe_type.h b/drivers/net/ixgbe/ixgbe_type.h index 76bf21b8a10d..f190a4a8faf4 100644 --- a/drivers/net/ixgbe/ixgbe_type.h +++ b/drivers/net/ixgbe/ixgbe_type.h @@ -2698,6 +2698,9 @@ struct ixgbe_info { #define IXGBE_ERR_EEPROM_VERSION -24 #define IXGBE_ERR_NO_SPACE -25 #define IXGBE_ERR_OVERTEMP -26 +#define IXGBE_ERR_FC_NOT_NEGOTIATED -27 +#define IXGBE_ERR_FC_NOT_SUPPORTED -28 +#define IXGBE_ERR_FLOW_CONTROL -29 #define IXGBE_ERR_SFP_SETUP_NOT_COMPLETE -30 #define IXGBE_ERR_PBA_SECTION -31 #define IXGBE_ERR_INVALID_ARGUMENT -32 -- 2.20.1