rtlwifi: Remove unused _usb_nbytes_read_write and _usb_writeN_sync

Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rtlwifi: Remove unused routine _usb_readN_sync

Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mwifiex: add cfg80211 handlers add/del_virtual_intf

Making adding and deleting virtual interfaces dynamic. Adding
handlers for creating and deleting virtual interface with
given name and dev respectively.

Also, creating default interface of type station on insmod of
the driver.

Signed-off-by: Yogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mwifiex: fix Tx data rate display issue

"iw dev mlan0 link" shows wrong data rate, because data rate is
not sent properly to cfg80211 stack. Also stack is not updated
with mcs and Tx data flags information.

Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mwifiex: remove unreachable code

In disconnected state "iw dev mlan0 link" command will return
from cfg80211 stack itself. We also have an error check in
mwifiex_cfg80211_get_station() routine. Therefore the code
under "if (!priv->media_connected)" condition in
mwifiex_rate_ioctl_get_rate_value() routine becomes unreachable.

Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mwifiex: remove unnecessary mwifiex_dump_station_info() call

An extra call to mwifiex_dump_station_info() routine in get_station
callback function is redundant

Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: Remove redundant my beacon check at ath_rx_ps_beacon

Make use of the rx status's is_mybeacon in order to avoid
redundant memcmp.

Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: Remove unnecessary AMPDU check at tx status

Fill the ampdu_[ack]_len for both aggregation and normal frames.
So that we could avoid unnecesary conditional at tx status.

Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mac80211: max_tp_rate2 management of minstrel_ht

I noticed a possible issue in the max_tp_rate2 management of
minstrel_ht. In particular, if we look up just among max_tp_rate2 of
each group it will be possible that the selected rate will not be the
mcs with second maximum throughput. I wrote this simple patch.

Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi83@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

wireless: at76c50x: use native hex_pack_byte() method

Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: "John W. Linville" <linville@tuxdriver.com>
Tested-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Merge branch 'master' of git://git.infradead.org/users/linville/wireless

Conflicts:
drivers/net/wireless/iwlwifi/iwl-scan.c
net/wireless/nl80211.c

mac80211: treat the WME sta flag as a bit

Correct flag usage - use it as a bit index instead of a bit value.

Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

wl3501_cs: min_t() cast truncates high bits

wrqu->encoding.length comes from the network administrator.  It's
size u16.  We want to limit "tocopy" to the smallest value of either
"len_keys", "wrqu->encoding.length" or 100.  But because .length
gets cast from u16 to u8 we might use a random, smaller value than
the was desired.  It's probably not very serious, but we may as well
fix it.

Btw, this is from code auditing and not from testing.  I don't know
if this affects anyone in real life.

Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mac80211: save tx params per sdata

save and configure tx param per sdata, rather than
per hardware.

Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

cfg80211/mac80211: add netdev param to set_txq_params()

tx params are currently configured per hw, although they
should be configured per interface.

Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mac80211: Send the management frame at requested rate

Whenever the scan request or tx_mgmt is requesting not to
use CCK rate for managemet frames through
NL80211_ATTR_TX_NO_CCK_RATE attribute, then mac80211 should
select appropriate least non-CCK rate. This could help to
send P2P probes and P2P action frames at non 11b rates
without diabling 11b rates globally.

Cc: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

nl80211/cfg80211: Add support to disable CCK rate for management frame

Add a new nl80211 attribute to specify whether to send the management
frames in CCK rate or not. As of now the wpa_supplicant is disabling
CCK rate at P2P init itself. So this patch helps to send P2P probe
request/probe response/action frames being sent at non CCK rate in 2GHz
without disabling 11b rates.

This attribute is used with NL80211_CMD_TRIGGER_SCAN and
NL80211_CMD_FRAME commands to disable CCK rate for management frame
transmission.

Cc: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

NFC: use after free on error

We returned a freed variable on some error paths when the intent was
to return a NULL.  Part of the reason this was missed was that the
code was confusing because it had too many gotos so I removed them
and simplified the flow a bit.

Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Lauro Ramos Venancio <lauro.venancio@openbossa.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwlagn: fix scan complete processing

When we cancel a scan, the completion runs
only from the workqueue. This can cause the
remain-on-channel scan to fail when another
one was just canceled, because we're still
aborting it.

To fix this, run the completion inline with
the lock still held before returning from
iwl_scan_cancel_timeout().

Also, to avoid the scan complete work from
completing a new scan prematurely, add a
new STATUS_SCAN_COMPLETE bit.

Reported-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Tested-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwlagn: move iwl_process_scan_complete up

To make the next patch easier to read, move
the function up, it'll be needed earlier in
this file in the next patch.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwlagn: refactor scan complete

We'll need to be able to run scan complete
inline, not from the workqueue, so refactor
it.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwlagn: make iwl_scan_cancel_timeout void

The return value of iwl_scan_cancel_timeout()
isn't used anywhere, so let's just remove it.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwlagn: remove Kelvin support

Only 5150 series devices report their temperature
in Kelvin, and for those we already convert it to
Celsius when storing into priv->temperature, so
there's no way priv->temperature will ever be in
Kelvin. Remove support for this.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwlagn: fix slot programming

When an AP mode interface is added with a DTIM
period of two, the slot programming is wrong.
Fix it by taking into account the DTIM period.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwlagn: fix dangling scan request

If iwl_scan_initiate() fails for any reason,
priv->scan_request and priv->scan_vif are left
dangling. This can lead to a crash later when
iwl_bg_scan_completed() tries to run a pending
scan request.

In practice, this seems to be very rare due to
the STATUS_SCANNING check earlier. That check,
however, is wrong -- it should allow a scan to
be queued when a reset/roc scan is going on.
When a normal scan is already going on, a new
one can't be issued by mac80211, so that code
can be removed completely. I introduced this
bug when adding off-channel support in commit
266af4c745952e9bebf687dd68af58df553cb59d.

Cc: stable@kernel.org [3.0]
Reported-by: Peng Yan <peng.yan@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwlagn: use kcalloc when possible for array allocation

As everybody knows kcalloc checks the multiplication is safe and
that we don't run into overflow.

Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwlagn: update rate scaling with BA notifications

In the current code, the rate scaling isn't fed with
statistics from the BA notifications.

This is since my patch:

iwlagn: reclaim the packets in transport layer

Fix that.

Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwlagn: add debugging to show probe related info in scan notification

Add debugging to show the status of probe in scan notification
to help debug probe related issues

Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwlagn: set the sequence control from the transport layer

Since all the queue logic has been moved to the transport layer,
the sequence number is set in the transport layer.
While doing that I forgot that the mac header is copied to the
TB of the TX cmd in the upper layer before the call to the transport
layer. So basically we used the sequence number from mac80211...
This was fine for the first assocation but after the second, mac80211
resets its counters while we don't hence a shift that led to terrible
impact on performance.

Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

MAINTAINERS: update iwlwifi

Change to iwlwifi.git instead of iwlwifi-2.6.git
iwlwifi-2.6.git still works for backward compatibility

Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwlagn: sparse warning priv->temperature is signed

Since priv->temperature is signed, we cannot use debugfs_create_u32
to refer to it.
Use a regular debugfs file instead.

Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwlagn: remove warning in iwl_rx_handle

Txid was used without being initialized.

Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: fix a regression in ath9k_ps_restore

After 'ath9k: optimize ath9k_ps_restore', it would only send the device to
network sleep and not to full sleep anymore, potentially causing more
battery drain.

Reported-by: Vivek Natarajan <nataraja@qca.qualcomm.com>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

NFC: protect nci_data_exchange transactions

Protect 'cb' and 'cb_context' arguments in nci_data_exchange.
In fact, this implements a queue with max length of 1 data
exchange transactions in parallel.

Signed-off-by: Ilan Elias <ilane@ti.com>
Acked-by: Lauro Ramos Venancio <lauro.venancio@openbossa.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

NFC: implicitly deactivate in nci_start_poll

When start_poll is called, and a target was implicitly activated,
we need to implicitly deactivate it.
On the other hand, when the target was activated by the user,
we should not deactivate it.

Signed-off-by: Ilan Elias <ilane@ti.com>
Acked-by: Lauro Ramos Venancio <lauro.venancio@openbossa.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

NFC: improve readability of an 'if' in nci core.c

Signed-off-by: Ilan Elias <ilane@ti.com>
Acked-by: Lauro Ramos Venancio <lauro.venancio@openbossa.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mwifiex: reset skb length before inserting to free queue

After handling command response, cmd skb is inserted into command
free queue(which keeps track of availabile skbs) for reuse purpose.
Skb length is not getting reset to zero here. This patch takes care
of it.

Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Yogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mwifiex: pass correct band parameter to ieee80211_channel_to_frequency()

ieee80211_channel_to_frequency() routine expects band parameter in
the form of "enum ieee80211_band band". Currently driver specific
band (BAND_A, BAND_AN etc.) is passed to the routine.

This patch makes sure that correct parameter is passed.

Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mwifiex: update bss band information

In recent commit "mwifiex: use cfg80211 dynamic scan..."
(7c6fa2a843..) scan table handling in driver is removed to
make use of cfg80211 dynamic scan table. Now driver sends
beacon buffers found in scanning directly to stack and parse
the buffer for requested BSS only during association.

Beacon buffer doesn't contain bss band information. Driver
gets it from firmware in separate tlv (chan_band_tlv).
Currently since we don't inform stack about bss bandinfo,
there is an issue with 5GHz association.

Use "priv" field of struct cfg80211_bss to store bandinfo.
This fixes 5GHz association issue.

Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mwifiex: fix 5GHz association issue

Sometimes association in 5GHz doesn't work. Dmesg log shows
"Can not find requested SSID xyz" error message. Currently
while preparing scan channel list for firmware Null entries
are created for disabled channels. The routine which retrieves
this list ignores channels after Null entry. Hence sometimes
driver doesn't scan the channel of requested AP and association
fails. The issue is fixed by avoiding those NULL entries.

Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

b43: LCN-PHY: minor clean ups

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

b43: update dummy transmission

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

b43: add missing MMIO defines

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

libertas: scan behaviour consistency improvements

When scanning for the broadcast SSID, there is no need to add the
SSID TLV (restoring the behaviour of the driver behaviour in the wext
days, confirmed in Marvell specifications).

If bssid is unspecified, the current scan code will usually fire off an
active scan probing for the specific requested SSID. However, if a scan
is ongoing (or has just finished), those scan results will be used
instead (even if that scan is totally different, e.g. a passive scan on
channel 4 for a different SSID). Fix this inconsistency by always
firing off a scan when associating without a bssid.

Signed-off-by: Daniel Drake <dsd@laptop.org>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

cfg80211: Validate cipher suite against supported ciphers

Instead of using a hardcoded list of cipher suites in nl80211.c, use a
shared function in util.c to verify that the driver advertises support
for the specified cipher. This provides more accurate validation of the
values and allows vendor-specific cipher suites to be added in drivers.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

cfg80211: Remove strict validation of AKM suites

NL80211_ATTR_AKM_SUITES can be used to configure new AKMs, like FT or
the SHA-256 -based AKMs or FT from 802.11r/802.11w. In addition, vendor
specific AKMs could be used. The current validation code for the connect
command prevents cfg80211-based drivers from using these mechanisms even
if the driver would not actually use this AKM value (i.e., it uses
WPA/RSN IE from user space). mac80211-based drivers allow any AKM to be
used since this value is not used there.

Remove the unnecessary validation step in cfg80211 to allow drivers to
decide what AKMs are supported. In theory, we could handle this by
advertising supported AKMs, but that would not be very effective unless
we enforce all drivers (including mac80211) to advertise the set of
supported AKMs. This would require additional changes in many places
whenever a new AKM is introduced even though no actually functionality
changes may be required in most drivers.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mac80211: add ieee80211_vif param to tsf functions

TSF can be kept per vif.
Add ieee80211_vif param to set/get/reset_tsf, and move
the debugfs entries to the per-vif directory.

Update all the drivers that implement these callbacks.

Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: add Block ACK bitmap in sample debug

this represents the bitmap of block ACK received after the
successful transmission of an aggregate frame. also made few
changes to beautify the display

Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Merge branch 'for-linville' of git://github.com/lucacoelho/wl12xx

Merge branch 'master' of git://github.com/padovan/bluetooth-next

ath9k: Fix a dma warning/memory leak

proper dma_unmapping and freeing of skb's has to be done in the rx
cleanup for EDMA chipsets when the device is unloaded and this also
seems to address the following warning which shows up occasionally when
the device is unloaded

Call Trace:
[<c0148cd2>] warn_slowpath_common+0x72/0xa0
[<c03b669c>] ? dma_debug_device_change+0x19c/0x200
[<c03b669c>] ? dma_debug_device_change+0x19c/0x200
[<c0148da3>] warn_slowpath_fmt+0x33/0x40
[<c03b669c>] dma_debug_device_change+0x19c/0x200
[<c0657f12>] notifier_call_chain+0x82/0xb0
[<c0171370>] __blocking_notifier_call_chain+0x60/0x90
[<c01713bf>] blocking_notifier_call_chain+0x1f/0x30
[<c044f594>] __device_release_driver+0xa4/0xc0
[<c044f647>] driver_detach+0x97/0xa0
[<c044e65c>] bus_remove_driver+0x6c/0xe0
[<c029af0b>] ? sysfs_addrm_finish+0x4b/0x60
[<c0450109>] driver_unregister+0x49/0x80
[<c0299f54>] ? sysfs_remove_file+0x14/0x20
[<c03c3ab2>] pci_unregister_driver+0x32/0x80
[<f92c2162>] ath_pci_exit+0x12/0x20 [ath9k]
[<f92c8467>] ath9k_exit+0x17/0x36 [ath9k]
[<c06523cd>] ? mutex_unlock+0xd/0x10
[<c018e27f>] sys_delete_module+0x13f/0x200
[<c02139bb>] ? sys_munmap+0x4b/0x60
[<c06547c5>] ? restore_all+0xf/0xf
[<c0657a20>] ? spurious_fault+0xe0/0xe0
[<c01832f4>] ? trace_hardirqs_on_caller+0xf4/0x180
[<c065b863>] sysenter_do_call+0x12/0x38
 ---[ end trace 16e1c1521c06bcf9 ]---
Mapped at:
[<c03b7938>] debug_dma_map_page+0x48/0x120
[<f92ba3e8>] ath_rx_init+0x3f8/0x4b0 [ath9k]
[<f92b5ae4>] ath9k_init_device+0x4c4/0x7b0 [ath9k]
[<f92c2813>] ath_pci_probe+0x263/0x330 [ath9k]

Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rtlwifi: rtl8192cu: Fix unitialized struct

Driver rtl8192cu assigns a new struct rtl_tcb_desc object, but fails to
clear it.

Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@kernel.org> [2.6.39+]
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwlagn: fix dangling scan request

If iwl_scan_initiate() fails for any reason,
priv->scan_request and priv->scan_vif are left
dangling. This can lead to a crash later when
iwl_bg_scan_completed() tries to run a pending
scan request.

In practice, this seems to be very rare due to
the STATUS_SCANNING check earlier. That check,
however, is wrong -- it should allow a scan to
be queued when a reset/roc scan is going on.
When a normal scan is already going on, a new
one can't be issued by mac80211, so that code
can be removed completely. I introduced this
bug when adding off-channel support in commit
266af4c745952e9bebf687dd68af58df553cb59d.

Cc: stable@kernel.org [3.0]
Reported-by: Peng Yan <peng.yan@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

wl12xx: report the stop_ba event to all STAs in AP-mode

Use the AP_MAX_LINKS as the upper boundary for traversing the links array,
thereby guaranteeing BA sessions with all connected STAs are stopped when
the stop_ba event is received.

Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>

wl12xx: correct fw_status structure for 8 sta support in AP-mode

Fix an erroneous labeling of array boundaries in the fw_status structure.

Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>

wl12xx: implement set_bitrate_mask callback

Save the configured bitrate, and use the min allowed rate
as the basic rate (e.g. when scanning).

Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>

wl12xx: AP mode - support hidden SSID

If a hidden SSID is requested, generate a probe response template
containing the real SSID.

Depends on the patch "mac80211: add ssid config to bss information
in AP-mode".

Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>

wl12xx: Use dev_hlid for auth and assoc req

On roaming, the auth and assoc req are sent with the sta
hlid. This is wrong, as the sta hlid is configured according
to the old ap. Use the dev_hlid instead.

Move the wl1271_tx_update_filters() call into wl1271_tx_get_hlid(),
so wl->dev_hlid will be valid.

Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>

wl12xx: send all pending packets on channel change

There is a race condition between wl1271_tx_work() and the
channel switch, so make sure all the pending packets are
being sent before switching channel.

Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>

wl12xx: remove P2P ie from probe response

wl12xx uses a single probe response template, regardless of
the probe request.
However, the P2P spec forbids including the p2p ie in some
cases (e.g. the probe request didn't include the p2p ie).

The fw responds only to probe requests that don't
include the p2p ie, and passes up probe requests that
include them (the supplicant will answer them).

Thus, strip the p2p ie from the probe response template.

Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>

wl12xx: remove TIM ie from probe response

wl12xx uses the beacon as the probe response template.
However, the beacon includes a TIM ie, which shouldn't
exist in the probe response.

Delete it from the skb before configuring the probe
response template.

Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>

wl12xx: Include OFDM rates in IBSS mode

We were including only 11b rates in IBSS mode.  This patch adds OFDM
rates.

[Rephrased commit log and removed one unnecessary comment. -- Luca]

Signed-off-by: Shahar Levi <shahar_levi@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>

wl12xx: fix sdio_test module functionality

Due to some changes in PM in recent kernels, the sdio_test module has
been broken for a while.  This patch fixes the code that powers the
card on and off.

Also made some small indentation fixes in the Makefile.

[Rephrased commit log and removed the change in the FW name, since
it's done in another patch. -- Luca]

Signed-off-by: Shahar Levi <shahar_levi@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>

wl12xx: fix forced passive scans

We were using incorrect max and min dwell times during forced passive
scans because we were still using the active scan states to scan
(passively) the channels that were not marked as passive.

Instead of doing passive scans in active states, we now skip active
states and scan for all channels in passive states.

Cc: <stable@kernel.org> # 2.6.36+
Signed-off-by: Luciano Coelho <coelho@ti.com>

nfc: NFC_WILINK depends on NFC_NCI

nwcwilink.c uses nci_*() interfaces, so it should depend on
NFC_NCI.

Fixes these build errors:
ERROR: "nci_register_device" [drivers/nfc/nfcwilink.ko] undefined!
ERROR: "nci_allocate_device" [drivers/nfc/nfcwilink.ko] undefined!
ERROR: "nci_recv_frame" [drivers/nfc/nfcwilink.ko] undefined!
ERROR: "nci_free_device" [drivers/nfc/nfcwilink.ko] undefined!
ERROR: "nci_unregister_device" [drivers/nfc/nfcwilink.ko] undefined!

Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mwifiex: remove unneeded NULL check

We dereference "rate" on the lines before so the checks here are too
late to help.  This function is only called from
mwifiex_dump_station_info() and "rate" is always a non-NULL pointer
so the check can be removed.

Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mwifiex: add a kfree() to an error path

We're not likely to hit this small memory leak, but lets fix it
anyway to keep the static checkers happy.

Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwlagn: remove duplicate list init

iwl_trans_rx_alloc is only called from iwl_rx_init, so no need
to init the lists twice.

Signed-off-by: Amit Beka <amit.beka@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwlagn: pending frames musn't be incremented if agg is on

During my works on the transport layer I removed code that updated
a local variable (is_agg) that is needed to keep the pending_frames
count up to date. Fix this.

Also, there should be no way to have a packet with TX_CTL_AMPDU set
while the internal aggregation state machine is not in AGG_ON state.
Add a WARN_ON to ensure that.

Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwlagn: remove uneeded declaration

This has been removed but the declaration hasn't.

Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwlagn: simplify the iwl_device_cmd layout

This simplifies both the transport layer and the upper layer.

Kill the union in the device command, which avoids the funny syntax
we had: cmd->cmd.payload.

Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwlagn: remove the callback in host commands

Before this patch, the upper layer could register a callback for each
host command. This mechanism allowed the upper layer to have
different callbacks for the same command ID. In fact, it wasn't used
and the rx_handlers is enough: same callback for all the command with
a specific command ID.

The iwl_send_add_station needs the access the command that was sent
while handling the response (regardless if the command was sent in
SYNC or ASYNC mode). So now, all the handlers receive the host
command that was sent. This implies a change in the handler signature.

Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwlagn: split remain-on-channel

If we're associated and want to do P2P at the same
time, the scan for remain-on-channel is currently
limited to 80ms because of the way the device will
behave in that case. Instead of doing that, split
up the dwell times into little pieces. It will not
actually be a single big dwell time then, but will
be close enough. This improves robustness of P2P
in such scenarios.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwlagn: remove common station priv

Since the driver split there's no more need for
shared/non-shared private station data so remove
struct iwl_station_priv_common entirely.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwlagn: move scan code to scan file

Since the driver split there's no longer a need
to have the scan code scattered across multiple
files, so move it all back to iwl-scan.c

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mac80211: notify peer when shutting down peer link

Send a Mesh Peering Close frame when we deactivate a mesh peer link.

Signed-off-by: Thomas Pedersen <thomas@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mac80211: fix AP/VLAN PS buffer race

When an AP interface is removed without the
AP/VLAN interfaces having been removed before
already, the AP-VLAN interface might still
have sleeping stations and buffer multicast
frames which will happen on the AP interface.
Thus, we need to remove AP/VLAN interfaces
before purging buffered broadcast frames.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

cfg80211: Fix validation of AKM suites

Incorrect variable was used in validating the akm_suites array from
NL80211_ATTR_AKM_SUITES. In addition, there was no explicit
validation of the array length (we only have room for
NL80211_MAX_NR_AKM_SUITES).

This can result in a buffer write overflow for stack variables with
arbitrary data from user space. The nl80211 commands using the affected
functionality require GENL_ADMIN_PERM, so this is only exposed to admin
users.

Cc: stable@kernel.org
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwlegacy: do not use interruptible waits

iwlegacy version of fix:

commit effd4d9aece9184f526e6556786a94d335e38b71
Author: Johannes Berg <johannes.berg@intel.com>
Date:   Thu Sep 15 11:46:52 2011 -0700

    iwlagn: do not use interruptible waits

    Since the dawn of its time, iwlwifi has used
    interruptible waits to wait for synchronous
    commands and firmware loading.

    This leads to "interesting" bugs, because it
    can't actually handle the interruptions; for
    example when a command sending is interrupted
    it will assume the command completed fully,
    and then leave it pending, which leads to all
    kinds of trouble when the command finishes
    later.

    Since there's no easy way to gracefully deal
    with interruptions, fix the driver to not use
    interruptible waits.

    This at least fixes the error
    iwlagn 0000:02:00.0: Error: Response NULL in  'REPLY_SCAN_ABORT_CMD'

    I have seen in P2P testing, but it is likely
    that there are other errors caused by this.

Cc: stable@kernel.org # 2.6.39+
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwlegacy: fix command queue timeout

iwlegacy version of fix:

commit 282cdb325aea4ebbc42ce753b47cc96145eb54bc
Author: Johannes Berg <johannes.berg@intel.com>
Date:   Mon Sep 12 12:09:10 2011 -0700

    iwlagn: fix command queue timeout

    If the command queue is constantly busy,
    which can happen in P2P, the hangcheck
    timer will frequently find a command in
    it and will eventually reset the device
    because nothing sets the timestamp for
    this queue when commands are processed.

    Fix this by setting the timestamp when
    a command completes.

iwlegacy does not support P2P, but this patch fix possible
unneeded hardware resets, hence is needed.

Cc: stable@kernel.org # 2.6.39+
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k_hw: Fix Rx DMA stuck for AR9003 chips

During the endurance testing, rx frames are not getting DMAd from
MAC whereas pcu rx frame counters are getting updated properly.
As per systems team input updated the initval to fix rx dma stuck
issue.

Cc: stable@kernel.org
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Bluetooth: mark l2cap_create_iframe_pdu as static

l2cap_create_iframe_pdu is only used in l2cap_core.c

Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>

Bluetooth: Check 'dev_class' in mgmt_device_found()

The mgmt_device_found event will be used to report LE devices found
during discovery procedure. Since LE advertising reports events
doesn't have class of device information, we need to check if
'dev_class' is not NULL before copying it.

Signed-off-by: Andre Guedes <andre.guedes@openbossa.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>

Bluetooth: Reduce critical region.

This patch reduces the critial region (protected by hdev->lock) in
hci_cc_le_set_scan_enable(). This way, only really required code is
synchronized.

Signed-off-by: Andre Guedes <andre.guedes@openbossa.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>

Bluetooth: Fix wrong memcpy size on LE start encryption

This patch fixes wrong memcpy size when copying rand value to
HCI_OP_LE_START_ENC command.
The compiler pretends that the array parameter was declared as a pointer
and sizeof reports the size of the pointer. [1]

[1] http://www.c-faq.com/aryptr/aryparmsize.html

Signed-off-by: Anderson Briglia <anderson.briglia@openbossa.org>
Signed-off-by: Anderson Lizardo <anderson.lizardo@openbossa.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>

Bluetooth: Remove support for other SMP keys than the LTK

For now, only the LTK is properly supported. We are able to receive
and generate the other types of keys, but we are not able to use
them. So it's better not request them to be distributed.

Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@openbossa.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>

Bluetooth: Fix not setting a pending security level

For slave initiated security, we should set a default security level,
for now BT_SECURITY_MEDIUM.

Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@openbossa.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>

Revert "Bluetooth: Add support for communicating keys with userspace"

This reverts commit 5a0a8b49746771fba79866fb9185ffa051a6a183.

If we use separate messages and list for SMP specific keys we can
simplify the code.

Conflicts:

net/bluetooth/mgmt.c

Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@openbossa.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>

Bluetooth: Use the LTK after receiving a LE Security Request

When receiving a security request from the remote device we should find
if there is already a LTK associated with the remote device, if found
we should use it to encrypt the link.

Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@openbossa.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>

Bluetooth: Fix sending wrong authentication requirements

Until we support any pairing method (Passkey Entry, OOB) that gives
MITM protection we shouldn't send that we have MITM protection.

Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@openbossa.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>

Bluetooth: Add mgmt events for blacklisting

Add management interface events for blocking/unblocking a device.
Sender of the block device command gets cmd complete and other
mgmt sockets get the event. Event is also sent to mgmt sockets when
blocking is done with ioctl, e.g when blocking a device with
hciconfig. This makes it possible for bluetoothd to track status
of blocked devices when a third party block or unblocks a device.

Event sending is handled in mgmt_device_blocked function which gets
called from hci_blacklist_add in hci_core.c. A pending command is
added in mgmt_block_device, so that it can found when sending the
event - the event is not sent to the socket from which the pending
command came. Locks were moved out from hci_core.c to hci_sock.c
and mgmt.c, because locking is needed also for mgmt_pending_add in
mgmt.c.

Signed-off-by: Antti Julku <antti.julku@nokia.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>

Bluetooth: Use the MEDIUM security level for pairings

This lifts the requirement of 16 digits pin codes when pairing
with devices that do not support SSP when using the mgmt interface.

Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@openbossa.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>

Bluetooth: Require authentication if MITM protection is requested

The HIGH security level requires a 16 digit pin code for non-SSP
bondings. Sometimes this requirement is not acceptable and we still
want protection againts MITM attacks (which is something that the
MEDIUM security level doesn't provide), for that we should allow
another way to request authentication without using the HIGH security
level.

Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@openbossa.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>

Bluetooth: Move SMP crypto functions to a workqueue

The function crypto_blkcipher_setkey() called by smp_e()
can sleep, so all the crypto work has to be moved to
hci_dev workqueue.

Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@openbossa.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>

Bluetooth: Move SMP fields to a separate structure

The objective is to make the core to have as little as possible
information about SMP procedures and logic. Now, all the SMP
specific information is hidden from the core.

Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@openbossa.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>

Bluetooth: hidp: Add support for NO_INIT_REPORTS quirk

During setup the host initializes all HID reports. Some devices do not
support this. If this quirk is set, we skip the initialization.
See also usbhid_init_reports() for this quirk.

Signed-off-by: David Herrmann <dh.herrmann@googlemail.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>

Bluetooth: Add LE link type for debugfs output

Add LE link type as known connection type for debugfs stringizing
output.

Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>

Bluetooth: Add mgmt command for fast connectable mode

Add command to management interface for enabling/disabling the
fast connectable mode.

Signed-off-by: Antti Julku <antti.julku@nokia.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>

Bluetooth: Add link_type information to the mgmt Connected event

One piece of information that was lost when using the mgmt interface,
was the type of the connection. Using HCI events we used to know
the type of the connection based on the type of the event, e.g.
HCI_LE_Connection_Complete for LE links.

Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@openbossa.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>

Bluetooth: Add support for running SMP without a socket

When doing the pairing procedure we won't have an associated
socket, but we still have to do the SMP negotiation. This
adds support for encrypting the link and exchanging keys.

Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@openbossa.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>