Samuel Ortiz [Fri, 10 May 2013 13:28:38 +0000 (15:28 +0200)]
NFC: Add secure elements addition and removal API
This API will allow NFC drivers to add and remove the secure elements
they know about or detect. Typically this should be called (asynchronously
or not) from the driver or the host interface stack detect_se hook.
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Samuel Ortiz [Fri, 10 May 2013 09:57:06 +0000 (11:57 +0200)]
NFC: Extend and fix the internal secure element API
Secure elements need to be discovered after enabling the NFC controller.
This is typically done by the NCI core and the HCI drivers (HCI does not
specify how to discover SEs, it is left to the specific drivers).
Also, the SE enable/disable API explicitely takes a SE index as its
argument.
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Samuel Ortiz [Tue, 7 May 2013 17:22:11 +0000 (19:22 +0200)]
NFC: Remove the static supported_se field
Supported secure elements are typically found during a discovery process
initiated when the NFC controller is up and running. For a given NFC
chipset there can be many configurations (embedded SE or not, with or
without a SIM card wired to the NFC controller SWP interface, etc...) and
thus driver code will never know before hand which SEs are available.
So we remove this field, it will be replaced by a real SE discovery
mechanism.
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Samuel Ortiz [Mon, 27 May 2013 13:29:11 +0000 (15:29 +0200)]
NFC: pn533: Copy NFCID2 through ATR_REQ
When using NFC-F we should copy the NFCID2 buffer that we got from
SENSF_RES through the ATR_REQ NFCID3 buffer. Not doing so violates
NFC Forum digital requirement #189.
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Samuel Ortiz [Mon, 27 May 2013 12:59:40 +0000 (14:59 +0200)]
NFC: pn533: Use 0x3 for SENSF_REQ Time Slot Number (TSN)
LLCP validation requires TSN to be 0x03 for type F.
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Frederic Danis [Wed, 29 May 2013 13:35:04 +0000 (15:35 +0200)]
NFC: Add NCI over SPI receive
Before any operation, driver interruption is de-asserted to prevent
race condition between TX and RX.
Transaction starts by emitting "Direct read" and acknowledged mode
bytes. Then packet length is read allowing to allocate correct NCI
socket buffer. After that payload is retrieved.
A delay after the transaction can be added.
This delay is determined by the driver during nci_spi_allocate_device()
call and can be 0.
If acknowledged mode is set:
- CRC of header and payload is checked
- if frame reception fails (CRC error): NACK is sent
- if received frame has ACK or NACK flag: unblock nci_spi_send()
Payload is passed to NCI module.
At the end, driver interruption is re asserted.
Signed-off-by: Frederic Danis <frederic.danis@linux.intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Frederic Danis [Wed, 29 May 2013 13:35:03 +0000 (15:35 +0200)]
NFC: Add NCI over SPI send
Before any operation, driver interruption is de-asserted to prevent
race condition between TX and RX.
The NCI over SPI header is added in front of NCI packet.
If acknowledged mode is set, CRC-16-CCITT is added to the packet.
Then the packet is forwarded to SPI module to be sent.
A delay after the transaction is added.
This delay is determined by the driver during nci_spi_allocate_device()
call and can be 0.
After data has been sent, driver interruption is re-asserted.
If acknowledged mode is set, nci_spi_send will block until
acknowledgment is received.
Signed-off-by: Frederic Danis <frederic.danis@linux.intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Frederic Danis [Wed, 29 May 2013 13:35:02 +0000 (15:35 +0200)]
NFC: Add basic NCI over SPI
The NFC Forum defines a transport interface based on
Serial Peripheral Interface (SPI) for the NFC Controller
Interface (NCI).
This module implements the SPI transport of NCI, calling SPI module
directly to read/write data to NFC controller (NFCC).
NFCC driver should provide functions performing device open and close.
It should also provide functions asserting/de-asserting interruption
to prevent TX/RX race conditions.
NFCC driver can also fix a delay between transactions if needed by
the hardware.
Signed-off-by: Frederic Danis <frederic.danis@linux.intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Samuel Ortiz [Fri, 24 May 2013 23:21:21 +0000 (01:21 +0200)]
NFC: HCI: Follow a positive code path in the HCI ops implementations
Exiting on the error case is more typical to the kernel coding style.
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Eric Lapuyade [Mon, 29 Apr 2013 15:47:42 +0000 (17:47 +0200)]
NFC: HCI: Implement fw_upload ops
This is a simple forward to the HCI driver. When driver is done with the
operation, it shall directly notify NFC Core by calling
nfc_fw_upload_done().
Signed-off-by: Eric Lapuyade <eric.lapuyade@intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Eric Lapuyade [Mon, 29 Apr 2013 15:13:27 +0000 (17:13 +0200)]
NFC: Add firmware upload netlink command
As several NFC chipsets can have their firmwares upgraded and
reflashed, this patchset adds a new netlink command to trigger
that the driver loads or flashes a new firmware. This will allows
userspace triggered firmware upgrade through netlink.
The firmware name or hint is passed as a parameter, and the driver
will eventually fetch the firmware binary through the request_firmware
API.
The cmd can only be executed when the nfc dev is not in use. Actual
firmware loading/flashing is an asynchronous operation. Result of the
operation shall send a new event up to user space through the nfc dev
multicast socket. During operation, the nfc dev is not openable and
thus not usable.
Signed-off-by: Eric Lapuyade <eric.lapuyade@intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Frederic Danis [Wed, 22 May 2013 09:36:17 +0000 (11:36 +0200)]
NFC: NCI: Fix skb->dev usage
skb->dev is used for carrying a net_device pointer and not
an nci_dev pointer.
Remove usage of skb-dev to carry nci_dev and replace it by parameter
in nci_recv_frame(), nci_send_frame() and driver send() functions.
NfcWilink driver is also updated to use those functions.
Signed-off-by: Frederic Danis <frederic.danis@linux.intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Wei Yongjun [Tue, 7 May 2013 12:07:52 +0000 (20:07 +0800)]
NFC: pn533: Fix error return code in pn533_probe()
Fix to return -ENOMEM in the nfc device alloc error handling
case instead of 0, as done elsewhere in this function.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Arron Wang [Mon, 22 Apr 2013 09:21:27 +0000 (17:21 +0800)]
NFC: pn544: Remove Felica and Jewel device presence check
There is no builtin command for driver to check the presence of
Felica and Jewel device, it is more reasonable for the userspace
daemon neard to build seperate commands to check the presence of
the card.
Signed-off-by: Arron Wang <arron.wang@intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Arron Wang [Mon, 22 Apr 2013 09:21:04 +0000 (17:21 +0800)]
NFC: pn544: Identify Type F NFC-DEP through NFCID2
NFCID2 is defined as the first 2 manufacturer ID (IDm) bytes.
NFC DEP (NFC peer to peer) devices Type-F NFCID2 must start with
0x01fe according to the NFC Digital Specification.
By checking those first 2 bytes we send the right command either to the
reader gate when NFCID2 != 0x1fe (The NFC tag case) or to the NFCIP1 gate
when seeing an NFC DEP device (The NFC peer to peer case).
Without this fix, Felica (Type F) tags are not properly detected with this
driver.
Signed-off-by: Arron Wang <arron.wang@intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
John W. Linville [Thu, 13 Jun 2013 17:34:29 +0000 (13:34 -0400)]
Merge branch 'for-linville-ath10k' of git://github.com/kvalo/ath6kl
John W. Linville [Thu, 13 Jun 2013 17:33:39 +0000 (13:33 -0400)]
Merge branch 'for-linville' of git://github.com/kvalo/ath6kl
Sujith Manoharan [Thu, 13 Jun 2013 03:22:09 +0000 (08:52 +0530)]
ath9k: Fix ANI trigger threshold
Since raising/lowering the limits based on INI has
been changed, the error limit for OFDM has to be 1000,
not 3500.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Christian Lamparter [Wed, 12 Jun 2013 19:35:39 +0000 (21:35 +0200)]
carl9170: add support for the new rate control API
With the new rate control API, the driver can now apply the
tx rate to outgoing frames just before they are uploaded to
the device. This is important because the rate control can
now react to fading or improving links a bit sooner.
Also, the driver no longer needs to sort the outgoing frames
for sample attempts (which affected the size of A-MPDUs and
the throughput of the link). For aggregated data frames, the
driver (and rate control) needs only to calculate and apply
a single set of tx rates to every subframe of the whole
aggregate.
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Wei Yongjun [Wed, 5 Jun 2013 02:16:55 +0000 (10:16 +0800)]
Bluetooth: btmrvl: fix error return code in btmrvl_sdio_card_to_host()
Fix to return -ENOMEM in the skb alloc error handling case
instead of 0, as done elsewhere in this function.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Cho, Yu-Chen [Tue, 4 Jun 2013 13:40:26 +0000 (21:40 +0800)]
Bluetooth: Add support for Mediatek Bluetooth device [0e8d:763f]
This patch adds support for Mediatek Bluetooth device
T: Bus=02 Lev=01 Prnt=01 Port=03 Cnt=01 Dev#= 2 Spd=480 MxCh= 0
D: Ver= 2.01 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=0e8d ProdID=763f Rev= 1.00
S: Manufacturer=MediaTek
S: Product=BT
S: SerialNumber=1.0
C:* #Ifs= 2 Cfg#= 1 Atr=a0 MxPwr=450mA
A: FirstIf#= 0 IfCount= 2 Cls=ff(vend.) Sub=ff Prot=ff
I:* If#= 0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=125us
E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=125us
E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms
I: If#= 1 Alt= 1 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms
I: If#= 1 Alt= 2 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms
I: If#= 1 Alt= 3 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms
I: If#= 1 Alt= 4 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms
I: If#= 1 Alt= 5 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms
I: If#= 1 Alt= 6 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
E: Ad=03(O) Atr=01(Isoc) MxPS= 63 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 63 Ivl=1ms
Signed-off-by: Cho, Yu-Chen <acho@suse.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
John W. Linville [Wed, 12 Jun 2013 19:39:05 +0000 (15:39 -0400)]
Merge branch 'for-john' of git://git./linux/kernel/git/jberg/mac80211-next
Conflicts:
drivers/net/wireless/iwlwifi/mvm/mac80211.c
John W. Linville [Wed, 12 Jun 2013 19:12:41 +0000 (15:12 -0400)]
Merge branch 'for-john' of git://git./linux/kernel/git/iwlwifi/iwlwifi-next
Arend van Spriel [Thu, 6 Jun 2013 11:18:07 +0000 (13:18 +0200)]
brcmfmac: add debugfs statistics for firmware-signalling
Added statistics for flow-control and packets dropped by the
driver.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Hante Meuleman [Thu, 6 Jun 2013 11:18:03 +0000 (13:18 +0200)]
brcmfmac: Always use fifo_credits, also for requested credits.
Currently firmware requested credits do not require fifo credits.
From a buffer management point of view this is incorrect. So
firwmware requested credits require also fifo credits before the
packet can be transferred to the host.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Stanislaw Gruszka [Wed, 12 Jun 2013 14:48:25 +0000 (16:48 +0200)]
Revert "iwl4965: workaround connection regression on passive channel"
This reverts commit
dd9c46408fdc07098333655ff27edf8cac8d9fcf.
With "iwl{4965,3495): workaround for firmware frame tx rejection"
patches we can enable IEEE80211_HW_REPORTS_TX_ACK_STATUS again.
Tested-by: Jake Edge <jake@lwn.net>
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Stanislaw Gruszka [Wed, 12 Jun 2013 14:44:50 +0000 (16:44 +0200)]
iwl3945: workaround for firmware frame tx rejection
Firmware can reject to transmit frame on passive channel, when it
did not yet received any frame with valid CRC on that channel.
Workaround this problem in the driver.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Stanislaw Gruszka [Wed, 12 Jun 2013 14:44:49 +0000 (16:44 +0200)]
iwl4965: workaround for firmware frame tx rejection
Firmware can reject to transmit frame on passive channel, when it
did not yet received any frame with valid CRC on that channel.
Workaround this problem in the driver.
Tested-by: Jake Edge <jake@lwn.net>
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Stanislaw Gruszka [Wed, 12 Jun 2013 14:44:48 +0000 (16:44 +0200)]
iwlegacy: add il_{stop,wake}_queues_by_reason functions
Add functions that will stop/wake all queues. Make them safe
regarding multiple calls and when some ac are stopped/woke
independently.
Tested-by: Jake Edge <jake@lwn.net>
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Stanislaw Gruszka [Wed, 12 Jun 2013 14:44:47 +0000 (16:44 +0200)]
iwlegacy: small refactoring of il_{stop,wake}_queue
Tested-by: Jake Edge <jake@lwn.net>
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Thomas Huehn [Tue, 11 Jun 2013 13:10:31 +0000 (15:10 +0200)]
ath5k: make use of the new rate control API
This patch enabels ath5k to use the new rate table to lookup each
mrr rate and retry information per packet.
Signed-off-by: Benjamin Vahl <bvahl@net.t-labs.tu-berlin.de>
Signed-off-by: Thomas Huehn <thomas@net.t-labs.tu-berlin.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Sujith Manoharan [Mon, 10 Jun 2013 08:19:40 +0000 (13:49 +0530)]
ath9k: Do not assign noise for NULL caldata
ah->noise is maintained globally and not per-channel. This
is updated in the reset() routine after the NF history has been
filled for the *current channel*, just before switching to
the new channel. There is no need to do it inside getnf(), since
ah->noise must contain a value for the new channel.
Cc: stable@vger.kernel.org
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Sujith Manoharan [Mon, 10 Jun 2013 08:19:39 +0000 (13:49 +0530)]
ath9k: Fix noisefloor calibration
The commits,
"ath9k: Fix regression in channelwidth switch at the same channel"
"ath9k: Fix invalid noisefloor reading due to channel update"
attempted to fix noisefloor calibration when a channel switch
happens due to HT20/HT40 bandwidth change. This is causing invalid
readings resulting in messages like:
"ath: phy16: NF[0] (-45) > MAX (-95), correcting to MAX".
This results in an incorrect noise being used initially for reporting
the signal level of received packets, until NF calibration is done
and the history buffer is updated via the ANI timer, which happens
much later.
When a bandwidth change happens, it is appropriate to reset
the internal history data for the channel. Do this correctly in the
reset() routine by checking the "chanmode" variable.
Cc: stable@vger.kernel.org
Cc: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Sujith Manoharan [Mon, 10 Jun 2013 08:19:38 +0000 (13:49 +0530)]
ath9k_hw: Assign default xlna config for AR9485
For AR9485 boards with XLNA, the default gpio config
is not set correctly, fix this.
Cc: stable@vger.kernel.org
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Hauke Mehrtens [Sun, 9 Jun 2013 16:59:43 +0000 (18:59 +0200)]
b43: activate N-PHY and HT-PHY support by default
N-PHY and HT-PHY support is more or less stable and should be activated
by default.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Hauke Mehrtens [Sun, 9 Jun 2013 16:59:42 +0000 (18:59 +0200)]
bcma: activate PCI host option by default
Most users are using bcma with a PCIe card, activate support for
this by default.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Hauke Mehrtens [Sun, 9 Jun 2013 16:53:58 +0000 (18:53 +0200)]
b43: ensue that BCMA is "y" when B43 is "y"
When b43 gets build into the kernel and it should use bcma we have to
ensure that bcma was also build into the kernel and not as a module.
In this patch this is also done for SSB, although you can not
build b43 without ssb support for now.
This fixes a build problem reported by Randy Dunlap in
5187EB95.
2060605@infradead.org
Reported-By: Randy Dunlap <rdunlap@infradead.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Oleksij Rempel [Sun, 9 Jun 2013 16:51:24 +0000 (18:51 +0200)]
ath9k_htc: add STBC TX support
All known ar7010+ar* device and current FW support STBC TX. This patch
make use of it and suggest to send STBC if peer support it.
I use wort "suggest" since currenly we have separate rate controller
in FW which will make decision based on rate and hardware.
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Kirshenbaum Erez [Sun, 9 Jun 2013 14:35:28 +0000 (17:35 +0300)]
wil6210: Fix AP/PCP start flow
WMI PCP Start flow should not be handled through:
net_device_ops->ndo_open()->wil_up()->__wil_up()
because it missing mandatory FW parameters (SSID,Channel,IEs, Security...).
Prior to AP starting __wil_up() may be called with iftype set
cfg80211_ops->change_virtual_intf(NL80211_IFTYPE_AP or STATION)
depend on the application hostapd/wpa_supplicant/iw.
there should not be an attempt to start an AP flow,
AP/PCP start flow will be started latter by cfg80211_ops->start_ap().
Signed-off-by: Kirshenbaum Erez <erezk@wilocity.com>
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Hauke Mehrtens [Sun, 9 Jun 2013 11:10:05 +0000 (13:10 +0200)]
wil6210: fix name of tracing config option
Tracing in wil6210 is activated with WIL6210_TRACING and not with
ATH6KL_TRACING, this is used for the ath6kl driver. Rename the config
option.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Acked-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Vladimir Kondratiev [Sun, 9 Jun 2013 06:12:55 +0000 (09:12 +0300)]
wil6210: Init Rx vring right after reset
at the vring initialisation, memory pool get allocated in the FW.
Make it 1-st because FW need this memory pool to precess
next commands
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Vladimir Kondratiev [Sun, 9 Jun 2013 06:12:54 +0000 (09:12 +0300)]
wil6210: Send EAPOL frames using normal Tx queue
No more need for special processing of EAPOL, FW can now send EAPOL frames
using normal Tx queue for TID 0
This fixes "schedule while atomic" bug - start_xmit called in softirq context;
while WMI mechanism that was used may sleep.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Vladimir Kondratiev [Sun, 9 Jun 2013 06:12:53 +0000 (09:12 +0300)]
wil6210: Derive IE's for AP
When starting secure AP, in some cases wpa_s provides probe template but not
probe/assoc IE's. In this case, derive missing IE's from probe.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Vladimir Kondratiev [Sun, 9 Jun 2013 06:12:52 +0000 (09:12 +0300)]
wil6210: improve frame type reporting
Report FC from the frame itself, as auxiliary information includes
only frame subtype. This is preparation for future changes, when
DMG beacon (extension frame) may be reported through wmi_evt_rx_mgmt()
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Vladimir Kondratiev [Sun, 9 Jun 2013 06:12:51 +0000 (09:12 +0300)]
wil6210: map more FW memory
map card's back-door debug data
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Vladimir Kondratiev [Sun, 9 Jun 2013 06:12:50 +0000 (09:12 +0300)]
wil6210: fix timeout for start_pcp
It may take up to 3500ms for the FW to start AP/PCP. Increase accordingly,
adding some safety margin.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Felix Fietkau [Fri, 7 Jun 2013 16:12:02 +0000 (18:12 +0200)]
ath9k: limit multicast buffer hardware queue depth
The CAB (Content after Beacon) queue is used for beacon-triggered
transmission of buffered multicast frames. If lots of multicast frames
were buffered and this queue fills up, it drowns out all regular
traffic. To limit the damage that buffered traffic can do, try to limit
the queued data to becaon_interval / 8.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Felix Fietkau [Fri, 7 Jun 2013 16:12:01 +0000 (18:12 +0200)]
ath9k: implement support for .release_buffered_frames()
This adds support for PS-Poll and U-APSD driver-buffered frames (part of
an aggregation session).
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Felix Fietkau [Fri, 7 Jun 2013 16:12:00 +0000 (18:12 +0200)]
ath9k: add support for IEEE80211_TX_CTL_PS_RESPONSE
Use the UAPSD hardware queue to get PS-Poll responses out as fast as
possible and without backoff.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Arend van Spriel [Fri, 7 Jun 2013 09:03:00 +0000 (11:03 +0200)]
brcmfmac: free primary net_device when brcmf_bus_start() fails
When initialization within brcmf_bus_start() fails on steps
before the brcmf_net_attach() the net_device for the primary
interface needs to be freed.
This patch resolves a panic during kernel boot as reported
by Stephen Warren.
ref.: http://mid.gmane.org/
51AD1F22.
2080004@wwwdotorg.org
Tested-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Arend van Spriel [Thu, 6 Jun 2013 11:49:32 +0000 (13:49 +0200)]
brcmfmac: Sent TIM information in case of data available.
When data is available and fw signalling is enabled then TIM
information should be sent to firmware. If it can piggy back
on existing packet then do that otherwise create dummy packet
to get information out.
Cc: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Arend van Spriel [Thu, 6 Jun 2013 11:18:06 +0000 (13:18 +0200)]
brcmfmac: increment hard_header_len instead of overriding
In brcmf_net_attach() the hard_header_len is set to sum of ETH_HLEN
and the headroom needed by the bus interface. Better use increment
instead as hard_header_len is already initialized upon alloc_netdev().
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Arend van Spriel [Thu, 6 Jun 2013 11:18:05 +0000 (13:18 +0200)]
brcmfmac: add trace event for capturing BDC header
The BDC header contains PropTx TLV signals that are useful to capture
for debugging. This event captures the header and tlv's in binary
form. This can be post-processed using trace-cmd plugin.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Arend van Spriel [Thu, 6 Jun 2013 11:18:02 +0000 (13:18 +0200)]
brcmfmac: fix send_pkts statistic counter in firmware-signalling
The statistic counter send_pkts was wrongly counted conditionally.
Correcting the mistake.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Hante Meuleman [Thu, 6 Jun 2013 11:18:01 +0000 (13:18 +0200)]
brcmfmac: Simplify counting transit count.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Hante Meuleman [Thu, 6 Jun 2013 11:18:00 +0000 (13:18 +0200)]
brcmfmac: Fix endless loop when brcmf_fws_commit_skb fails.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Hante Meuleman [Thu, 6 Jun 2013 11:17:59 +0000 (13:17 +0200)]
brcmfmac: Signalling header push and pull on logic places.
Currently suppressed packets get enque-ed with header which
then gets pulled before transmit. It is more logical and clean
to pull the header on return and push it unconditionally on xmit.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Hante Meuleman [Thu, 6 Jun 2013 11:17:58 +0000 (13:17 +0200)]
brcmfmac: Accept only first creditmap event.
During P2P testing it turned out that the firmware sents multiple
multiple creditmap event messages. Only the first message from the
firmware should be processed. Otherwise the firmware-signalled flow
control can run haywire when it has packets outstanding in firmware.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Hante Meuleman [Thu, 6 Jun 2013 11:17:57 +0000 (13:17 +0200)]
brcmfmac: fix invalid ifp lookup in firmware-signalling
The destination entries for firmware-signalled flow control have
the interface id stored. This needs to be translated to bsscfg
index when looking up the ifp object for the interface.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Hante Meuleman [Thu, 6 Jun 2013 11:17:56 +0000 (13:17 +0200)]
brcmfmac: Find correct MAC descriptor in case of TDLS.
In case of TDLS find the correct MAC descriptor for fw signalling
data. In case of TDLS each destination gets its own entry. This
was not handled correctly for P2P client.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Hante Meuleman [Thu, 6 Jun 2013 11:17:54 +0000 (13:17 +0200)]
brcmfmac: Correct creditmap when credit borrowing is active.
When credit borrowing is active the BE credits have been depleted,
however the worker should still be scheduled. In case of credit
borrowing correct credit map to make sure worker remains active.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Hante Meuleman [Thu, 6 Jun 2013 11:17:53 +0000 (13:17 +0200)]
brcmfmac: For FW signalling it is necessary to track gen bit.
Store gen bit on suppressed packet per entry and use latest
stored version for each packet which gets transmitted to fw.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Hante Meuleman [Thu, 6 Jun 2013 11:17:52 +0000 (13:17 +0200)]
brcmfmac: On bus flow control use fw signalling or netif.
Currently on a bus flow control both fws is informed and netif queue
gets closed. In case of fw signalling enabled, let the flow control
be handled by fw signalling only.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Arend van Spriel [Thu, 6 Jun 2013 11:17:51 +0000 (13:17 +0200)]
brcmfmac: reducing debug logging in firmware-signalling code
The debug logging in firmware-signalling code was rather extensive and
for a large part in the data path. This patch removes large part or the
level is changed to DATA level.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Arend van Spriel [Thu, 6 Jun 2013 11:17:50 +0000 (13:17 +0200)]
brcmfmac: explicitly indicate sk_buff is sent upon request credit
Firmware can request the driver for transmit packets using two different
signals. Only for one signal a flag was set in the sk_buff control
buffer. This patch adds explicit flag for the other signal as well.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Arend van Spriel [Thu, 6 Jun 2013 11:17:49 +0000 (13:17 +0200)]
brcmfmac: rework credit pickup to assure consistent handling
Reworked brcmf_skb_pick_up_credit() so it can be used for both
fcmode flavours in the same way.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Hante Meuleman [Thu, 6 Jun 2013 11:17:48 +0000 (13:17 +0200)]
brcmfmac: Take bus flowcontrol at credit mgmt into account.
On bus flow control (no more host bus resources to send packets
to device) the netif flow control was toggled, however credit
management should also take this status into account. Since there
are multiple sources handling this flow control necessary spinlocks
were added to protect flow control related data/states.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Arend van Spriel [Thu, 6 Jun 2013 11:17:47 +0000 (13:17 +0200)]
brcmfmac: remove fifo bitfield from brcmf_skbuff_cb::if_flags
The brcmf_skbuff_cb structure contain if_flags and htod fields. Both
have a bitfield defined to hold the fifo number. With a small code
change we get rid of the fifo bitfield in if_flags.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Arend van Spriel [Thu, 6 Jun 2013 11:17:46 +0000 (13:17 +0200)]
brcmfmac: allow firmware-signal tlv to be longer than specified
The firmware-signal API specification defines length for the different
tlv. During testing on different devices it turned out not all firmware
used the tlv length according specification. Therefore the length check
is made less strict with this patch.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Gabor Juhos [Thu, 6 Jun 2013 07:36:20 +0000 (09:36 +0200)]
rt2x00: rt2800usb: nuke rt2800usb_ops_5592
It is exactly the same like the generic rt2800usb_ops.
Remove the duplicate and use the generic ops for all
devices.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Gabor Juhos [Thu, 6 Jun 2013 07:36:19 +0000 (09:36 +0200)]
rt2x00: move extra_tx_headroom field from rt2x00_ops to rt2x00_dev
The extra_tx_headroom field of struct rt2x00_ops
indicates the extra TX headroom size required for
a given device. This data is redundant, the value
can be computed from the desc_size and winfo_size
fields of the TX queues.
Move the extra_tx_headroom field to struct rt2x00_dev,
compute its value in the probe routine and use the
cached value in the rest of the code.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Luis R. Rodriguez [Thu, 6 Jun 2013 03:45:36 +0000 (20:45 -0700)]
ath: add VHT80 support for regulatory domains
This adds VHT80 support for the QCA world regulatory
domains.
Cc: kvalo@qca.qualcomm.com
Signed-off-by: Luis R. Rodriguez <mcgrof@do-not-panic.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Wei Yongjun [Wed, 5 Jun 2013 02:16:33 +0000 (10:16 +0800)]
iwlegacy: fix error return code in il3945_pci_probe()
Fix to return a negative error code in the il3945_hw_set_hw_params() error
handling case instead of 0, as done elsewhere in this function.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Acked-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Avinash Patil [Tue, 4 Jun 2013 23:20:38 +0000 (16:20 -0700)]
mwifiex: enable/disable tx_amsdu support via module parameter
This patch disables tx_amsdu support in mwifiex by default.
tx_amdsu support can be enabled via module parameter at load time.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Amitkumar Karwar [Tue, 4 Jun 2013 23:19:56 +0000 (16:19 -0700)]
mwifiex: fix regression issue for usb interface
PATCH "mwifiex: scan delay timer cleanup in unload path" adds code
to cancel scan delay timer in unload path. It causes a regression
for USB interface.
USB8797 card gets enumerated twice. First enumeration is for
firmware download and second enumeration expects firmware
initialization.
It was observed that we are trying del_timer_sync() without setting
up the timer when remove handler is called after first enumeration.
This patch moves setup_timer() call to appropriate place so that
timer is setup for both the enumerations.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Gabor Juhos [Tue, 4 Jun 2013 11:40:50 +0000 (13:40 +0200)]
rt2x00: remove data_queue_desc struct
If the queue_init callback is implemented
by a driver it gets used instead of the
data_queue_desc based initialization.
The queue_init callback is implemented for
each drivers now, so the old initialization
method is not used anymore. Remove the unused
data_queue_desc structure and all of the
related code.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Gabor Juhos [Tue, 4 Jun 2013 11:40:49 +0000 (13:40 +0200)]
rt2x00: rt2500usb: implement queue_init callback
The generic rt2x00 code has been changed to allow the
drivers toimplement dynamic data_queue initialization.
Remove the static data queue descriptor structures
and implement the queue_init callback instead.
Compile tested only.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Gabor Juhos [Tue, 4 Jun 2013 11:40:48 +0000 (13:40 +0200)]
rt2x00: rt61pci: implement queue_init callback
The generic rt2x00 code has been changed to allow the
drivers toimplement dynamic data_queue initialization.
Remove the static data queue descriptor structures
and implement the queue_init callback instead.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Tested-by: Jakub Kicinski <kubakici@wp.pl>
Acked-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Gabor Juhos [Tue, 4 Jun 2013 11:40:47 +0000 (13:40 +0200)]
rt2x00: rt2500pci: implement queue_init callback
The generic rt2x00 code has been changed to allow the
drivers toimplement dynamic data_queue initialization.
Remove the static data queue descriptor structures
and implement the queue_init callback instead.
Compile tested only.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Gabor Juhos [Tue, 4 Jun 2013 11:40:46 +0000 (13:40 +0200)]
rt2x00: rt2400pci: implement queue_init callback
The generic rt2x00 code has been changed to allow the
drivers toimplement dynamic data_queue initialization.
Remove the static data queue descriptor structures
and implement the queue_init callback instead.
Compile tested only.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Gabor Juhos [Tue, 4 Jun 2013 11:40:45 +0000 (13:40 +0200)]
rt2x00: rt73usb: implement queue_init callback
The generic rt2x00 code has been changed to allow the
drivers toimplement dynamic data_queue initialization.
Remove the static data queue descriptor structures
and implement the queue_init callback instead.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Gabor Juhos [Tue, 4 Jun 2013 11:40:44 +0000 (13:40 +0200)]
rt2x00: rt2800pci: implement queue_init callback
The generic rt2x00 code has been changed to allow the
drivers toimplement dynamic data_queue initialization.
Remove the static data queue descriptor structures
and implement the queue_init callback instead.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Gabor Juhos [Tue, 4 Jun 2013 11:40:43 +0000 (13:40 +0200)]
rt2x00: rt2800usb: implement queue_init callback
The generic rt2x00 code has been changed to allow the
drivers toimplement dynamic data_queue initialization.
Remove the static data queue descriptor structures
and implement the queue_init callback instead.
The actual chipset is already known when the callback
is used. This allows us to use a single callback for
all supported devices.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Gabor Juhos [Tue, 4 Jun 2013 11:40:42 +0000 (13:40 +0200)]
rt2x00: add queue_init callback to rt2x00_ops
The driver uses static data structures for initializing
specific fields of a given data queue. These static
queue data descriptor structures are containing values
which related to a given chipset.
Even though the values are chip specific, the actual
selection of the used structure is based on device
specific vendor/product identifiers. This approach works,
but it is not always reliable. Sometimes the vendor and/or
device IDs of the PCI and USB devices contains improper
values which makes it impossible to select the correct
structure for such devices.
The patch adds a new callback to tr2x00_ops which
is called after the chipset detection is finished.
This allows the drivers to do dynamic initialization
of the data_queue structure for a given queue based
on the actual chipset.
After each driver implements the queue_init callback,
the data_queue_desc structure will be removed.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Gabor Juhos [Tue, 4 Jun 2013 11:40:41 +0000 (13:40 +0200)]
rt2x00: rt2x00queue: setup queue->threshold from queue->limit
Use the queue->limit value instead of the
qdesc->entry_num to compute the threshold.
The two source values are the same and the
data queue descriptor structure will be
removed by a later patch.
Also separate the computation from the rest
of the init code to make further changes
easier.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Gabor Juhos [Tue, 4 Jun 2013 11:40:40 +0000 (13:40 +0200)]
rt2x00: rt2x00dev: use rt2x00dev->bcn->limit
The beacon data queue is initialized already,
so fetch the number of the queue entries from
that instead of using the entry_num field of
the data queue descriptor.
The two values are the same, and the use of the
rt2x00dev->bcn->limit value allows us to get rid
of a superfluous pointer dereference.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Gabor Juhos [Tue, 4 Jun 2013 11:40:39 +0000 (13:40 +0200)]
rt2x00: rt2x00queue: remove qdesc parameter of rt2x00queue_alloc_entries
The qdesc parameter is not used anymore, so remove that.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Gabor Juhos [Tue, 4 Jun 2013 11:40:38 +0000 (13:40 +0200)]
rt2x00: rt2x00queue: add priv_size field to struct data_queue
Add a new field into struct data_queue and store
the size of the per-queue_entry private data in
that. Additionally, use the new field in the
rt2x00queue_alloc_entries function to compute
the size of the queue entries for a given queue.
The patch does not change the current behaviour
but makes it possible to remove the queue_desc
parameter of the rt2x00queue_alloc_entries function.
That will be done by a subsequent patch.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Sujith Manoharan [Tue, 4 Jun 2013 10:11:35 +0000 (15:41 +0530)]
ath9k: Remove unused ANI macros
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Sujith Manoharan [Tue, 4 Jun 2013 10:11:34 +0000 (15:41 +0530)]
ath9k: Remove redundant code
The phy error mask registers are programmed already
in ath9k_ani_restart(), so there is no need to set them
in ath9k_ani_reset().
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Sujith Manoharan [Tue, 4 Jun 2013 10:11:33 +0000 (15:41 +0530)]
ath9k: Fix ofdm weak signal configuration
The commit, "ath9k_hw: improve ANI processing and rx desensitizing parameters"
removed code setting various phy registers holding threshold values.
This is likely required for OFDM weak signal detection to function
correctly, so add them, but skip AR9462 and AR9565.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Sujith Manoharan [Tue, 4 Jun 2013 10:11:32 +0000 (15:41 +0530)]
ath9k: Fix ANI levels
The commit, "ath9k_hw: improve ANI processing and rx desensitizing parameters"
modified the immunity level tables for both CCK and OFDM. Fix them
so that the tables are in sync with the internal driver/codebase.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Sujith Manoharan [Tue, 4 Jun 2013 10:11:31 +0000 (15:41 +0530)]
ath9k: Fix ANI monitoring
The commit "ath9k_hw: improve ANI processing and rx desensitizing parameters"
changed various ANI operational parameters to address a specific
card/environment. This is not really applicable for other cards
in general usage.
As per internal documentation, lowering the immunity level can be
done only after 5 periods have passed and the CCK/OFDM errors are
below the low watermak threshold - which have been fixed at 300 and
400 respectively by the sytems team.
Raising the immunity level can be done when CCK/OFDM errors exceed
600 and 1000 (per second).
Set these values once during attach.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Sujith Manoharan [Tue, 4 Jun 2013 10:11:30 +0000 (15:41 +0530)]
ath9k: Fix OFDM weak signal detection for AP mode
The commit "ath9k_hw: improve ANI processing and rx desensitizing parameters"
changed the OFDM weak signal detection logic to disable it
for AP mode, which is not allowed. Fix this and enable it always
for AP mode.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
John W. Linville [Wed, 12 Jun 2013 18:35:23 +0000 (14:35 -0400)]
Merge branch 'master' of git://git./linux/kernel/git/linville/wireless
Conflicts:
drivers/net/wireless/ath/ath9k/Kconfig
net/mac80211/iface.c
Kalle Valo [Wed, 12 Jun 2013 17:52:10 +0000 (20:52 +0300)]
ath10k: mac80211 driver for Qualcomm Atheros 802.11ac CQA98xx devices
Here's a new mac80211 driver for Qualcomm Atheros 802.11ac QCA98xx devices.
A major difference from ath9k is that there's now a firmware and
that's why we had to implement a new driver.
The wiki page for the driver is:
http://wireless.kernel.org/en/users/Drivers/ath10k
The driver has had many authors, they are listed here alphabetically:
Bartosz Markowski <bartosz.markowski@tieto.com>
Janusz Dziedzic <janusz.dziedzic@tieto.com>
Kalle Valo <kvalo@qca.qualcomm.com>
Marek Kwaczynski <marek.kwaczynski@tieto.com>
Marek Puzyniak <marek.puzyniak@tieto.com>
Michal Kazior <michal.kazior@tieto.com>
Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Kees Cook [Fri, 10 May 2013 21:48:21 +0000 (14:48 -0700)]
b43: stop format string leaking into error msgs
The module parameter "fwpostfix" is userspace controllable, unfiltered,
and is used to define the firmware filename. b43_do_request_fw() populates
ctx->errors[] on error, containing the firmware filename. b43err()
parses its arguments as a format string. For systems with b43 hardware,
this could lead to a uid-0 to ring-0 escalation.
CVE-2013-2852
Signed-off-by: Kees Cook <keescook@chromium.org>
Cc: stable@vger.kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Sujith Manoharan [Thu, 6 Jun 2013 04:36:29 +0000 (10:06 +0530)]
ath9k: Use minstrel rate control by default
The ath9k rate control algorithm has various architectural
issues that make it a poor fit in scenarios like congested
environments etc.
An example: https://bugzilla.redhat.com/show_bug.cgi?id=927191
Change the default to minstrel which is more robust in such cases.
The ath9k RC code is left in the driver for now, maybe it can
be removed altogether later on.
Cc: stable@vger.kernel.org
Cc: Jouni Malinen <jouni@qca.qualcomm.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Felix Fietkau [Mon, 3 Jun 2013 09:18:57 +0000 (11:18 +0200)]
Revert "ath9k_hw: Update rx gain initval to improve rx sensitivity"
This reverts commit
68d9e1fa24d9c7c2e527f49df8d18fb8cf0ec943
This change reduces rx sensitivity with no apparent extra benefit.
It looks like it was meant for testing in a specific scenario,
but it was never properly validated.
Cc: rmanohar@qca.qualcomm.com
Cc: stable@vger.kernel.org
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Sujith Manoharan [Sat, 1 Jun 2013 01:38:09 +0000 (07:08 +0530)]
ath9k: Disable PowerSave by default
Almost all the DMA issues which have plagued ath9k (in station mode)
for years are related to PS. Disabling PS usually "fixes" the user's
connection stablility. Reports of DMA problems are still trickling in
and are sitting in the kernel bugzilla. Until the PS code in ath9k is
given a thorough review, disbale it by default. The slight increase
in chip power consumption is a small price to pay for improved link
stability.
Cc: stable@vger.kernel.org
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
projects / GitHub / exynos8895 / android_kernel_samsung_universal8895.git / log