Mark Brown [Sun, 21 Aug 2011 17:07:44 +0000 (18:07 +0100)]
ASoC: Provide more detail on WM8962 thermal shutdown status
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Mark Brown [Sun, 21 Aug 2011 10:47:14 +0000 (11:47 +0100)]
ASoC: Report IRQ_NONE when we don't see an interrupt from WM8962
This should never happen with level triggered IRQs.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Mark Brown [Wed, 17 Aug 2011 01:03:51 +0000 (10:03 +0900)]
ASoC: Initial WM8962 DSP2 support
The WM8962 features a DSP providing a number of signal processing
features including HD Bass and Virtual Surround Sound (VSS). Enable
initial support for this, allowing users to enable and disable the
algorithms using the default coefficient sets. Further patches will
add support for runtime configuration of the DSP coefficients.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Mark Brown [Sun, 21 Aug 2011 09:54:38 +0000 (10:54 +0100)]
ASoC: Add basic WM8962 capture low/high pass filter control
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Mark Brown [Sat, 20 Aug 2011 18:28:59 +0000 (19:28 +0100)]
ASoC: Optimise WM8996 no interrupt path
This occurs frequently if we are in edge triggered mode as we must poll the
interrupt status register until we get no more interrupts so it's worth
the effort - it means we skip writing null acknowledgements to the chip.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Mark Brown [Sat, 20 Aug 2011 18:00:50 +0000 (19:00 +0100)]
ASoC: Automatically manage WM8996 MICBIAS regulating mode
For non-audio uses like accessory detection we can use a lower quality,
unregulated microphone bias, saving a little power. As the hardware can
manually enable and disable the biases we can select regulating mode
automatically with supply widgets connected to the biases.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Axel Lin [Thu, 18 Aug 2011 07:31:04 +0000 (15:31 +0800)]
ASoC: sta32x: Move resource allocation and release to the corresponding callback functions
This patch includes below small fixes:
1. Move sta32x_set_bias_level() from sta32x_i2c_remove() to sta32x_remove().
2. Remove a redundant regulator_bulk_free() call in sta32x_i2c_remove(),
as we will call regulator_bulk_free() in sta32x_remove().
3. Remove unneeded snd_soc_codec_set_drvdata(codec, NULL) in sta32x_i2c_remove.
The i2c core will set the clientdata to NULL.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Johannes Stezenbach <js@sig21.net>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Mark Brown [Thu, 18 Aug 2011 16:20:36 +0000 (01:20 +0900)]
Merge branch 'for-3.1' into for-3.2
Jarkko Nikula [Thu, 18 Aug 2011 12:02:47 +0000 (15:02 +0300)]
ASoC: omap: Fix build errors in ams-delta
Fix "error: too few arguments to function 'ams_delta_set_bias_level'"
build errors in ams-delta.c that were introduced after commit
d4c6005 ("ASoC:
Add context parameter to card DAPM callbacks") by adding dapm context
to ams_delta_set_bias_level calls.
Signed-off-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Mark Brown [Wed, 17 Aug 2011 07:34:05 +0000 (16:34 +0900)]
Merge branch 'for-3.1' into for-3.2
Axel Lin [Wed, 17 Aug 2011 07:14:33 +0000 (15:14 +0800)]
ASoC: Remove unreachable code in au1xac97c_drvprobe and au1xi2s_drvprobe
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Sascha Hauer [Wed, 17 Aug 2011 07:20:01 +0000 (09:20 +0200)]
ASoC: Fix check for symmetric rate enforcement
The ASoC core tries to not enforce symmetric rates when
two streams open simultaneously. It does so by checking
rtd->rate being zero. This works exactly once after booting
because it is not set to zero again when the streams close.
Fix this by setting rtd->rate when no active stream is left.
[This leads to lots of warnings about not enforcing the symmetry in some
situations as there's a race in the userspace API where we know we've
got two applications but don't know what rates they want to set.
-- broonie ]
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Timur Tabi [Wed, 17 Aug 2011 01:58:29 +0000 (21:58 -0400)]
ASoC: fsl: fix build warning in fsl_dma
The previous patch to fsl_dma.c ("fix initialization of DMA buffers")
left behind an unused local variable that causes a build warning.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Mark Brown [Wed, 17 Aug 2011 06:14:17 +0000 (15:14 +0900)]
ASoC: Fix backport of WM8994 thermal warning
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Timur Tabi [Tue, 16 Aug 2011 22:47:45 +0000 (18:47 -0400)]
ASoC: claim the IRQ when the fsl_ssi device is probed, not opened
The PowerPC Freescale SSI driver is claiming the IRQ when the IRQ when
the device is opened, which means that the /proc/interrupts entry for
the SSI exists only during playback or capture. This also meant that
the user won't know that the IRQ number is wrong until he tries to use
the device. Instead, we should claim the IRQ when the device is probed.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Lars-Peter Clausen [Mon, 15 Aug 2011 18:15:23 +0000 (20:15 +0200)]
ASoC: Blackfin: ADAU1373 eval board support
Add a machine driver to support the EVAL-ADAU1373 board connected to a
Analog Devices BF5XX evaluation board.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Lars-Peter Clausen [Mon, 15 Aug 2011 18:15:22 +0000 (20:15 +0200)]
ASoC: Add ADAU1373 codec support
This patch adds support for the Analog Devices ADAU1373 audio codec.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Mark Brown [Tue, 16 Aug 2011 03:01:27 +0000 (12:01 +0900)]
ASoC: Implement WM8994 thermal warning and shutdown interrupt support
ALSA doesn't really have good mechanisms for dealing with these so we just
log them - the hardware already has automatic shutdown support.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Mark Brown [Tue, 16 Aug 2011 01:08:48 +0000 (10:08 +0900)]
ASoC: Add WM8958 noise gate support
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Mark Brown [Tue, 16 Aug 2011 12:36:38 +0000 (21:36 +0900)]
ASoC: Run Speyside WM8962 at 512fs
Ensure we have access to all the advanced DSP functinality offered by the
WM8962 by running the system clock at 512fs.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Lars-Peter Clausen [Mon, 15 Aug 2011 18:15:21 +0000 (20:15 +0200)]
ASoC: DAPM: Allow multiple mixer sources to be routed via the same switch
Currently it is only possible to route one source per switch into a mixer.
This patch modifies the code, so that it is possible to route multiple sources
into a mixer via the same switch. One use-case for this is routing a stereo
channel pair into a mono-mixer via the same switch.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Mark Brown [Mon, 15 Aug 2011 02:01:02 +0000 (11:01 +0900)]
ASoC: Disable pulls on WM8994 AIF2 when starting it
Pull control is availalbe for WM8994 AIF2, generally disabled as part of
the GPIO configuration in order to save power after system startup. As on
newer devices in the series there is no GPIO functionality on these pins
this will happen less naturally so have the driver disable the pulls as the
AIF is probed.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Mark Brown [Sun, 14 Aug 2011 10:07:33 +0000 (19:07 +0900)]
ASoC: Correct revision display for WM1250-EV1 module
The hardware documentation uses revision numbers starting at 1.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Mark Brown [Wed, 3 Aug 2011 08:31:26 +0000 (17:31 +0900)]
ASoC: Add device tree binding for WM8741
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Axel Lin [Sun, 14 Aug 2011 03:31:04 +0000 (11:31 +0800)]
ASoC: sta32x: shortcut the for loop to get ir and mcs
There is exactly one match or no match at all during the for loop iteration,
thus we can break from the for loop once a match is found.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Johannes Stezenbach <js@sig21.net>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Axel Lin [Mon, 15 Aug 2011 08:38:34 +0000 (16:38 +0800)]
ASoC: nuc900-pcm: remove unused variable 'dai'
Remove unused variable 'dai' to eliminate below warning.
CC sound/soc/nuc900/nuc900-pcm.o
sound/soc/nuc900/nuc900-pcm.c: In function 'nuc900_dma_new':
sound/soc/nuc900/nuc900-pcm.c:321: warning: unused variable 'dai'
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Axel Lin [Sun, 14 Aug 2011 00:00:12 +0000 (08:00 +0800)]
ASoC: soc-pcm: Remove unused global mutex
Since commit
b8c0dab9bf3373010e857a8d3f1b594c60a348dd
"ASoC: core - PCM mutex per rtd",
the global pcm_mutex is not being used any more.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Axel Lin [Sat, 13 Aug 2011 13:27:16 +0000 (21:27 +0800)]
ASoC: soc-cache: Remove unneeded codec_drv pointer variable in snd_soc_lzo_get_blksize
Since commit
aea170a099793abcd0e6de46b947458073204241
"ASoC: soc-cache: Add reg_size as a member to snd_soc_codec",
the codec_drv pointer variable is not used in snd_soc_lzo_get_blksize.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Axel Lin [Sat, 13 Aug 2011 13:12:01 +0000 (21:12 +0800)]
ASoC: soc-cache: Remove unneeded codec_drv pointer variable in snd_soc_flat_cache_init
Since commit
d779fce5d79525d66269c8f6e430e1515d697f3d
"ASoC: soc-cache: Ensure flat compression uses a copy of the defaults cache",
the codec_drv pointer variable is not used any more.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Axel Lin [Sat, 13 Aug 2011 03:32:56 +0000 (11:32 +0800)]
ASoC: s6000-pcm: remove unused variable 'dai'
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Daniel Glöckner <dg@emlix.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Mark Brown [Mon, 15 Aug 2011 13:48:19 +0000 (22:48 +0900)]
Merge branch 'for-3.1' into for-3.2
Remove the bodge for ad193x.
Conflicts:
sound/soc/soc-io.c
Scott Jiang [Fri, 12 Aug 2011 22:04:14 +0000 (18:04 -0400)]
ASoC: ad193x: remove cache support
asoc cache layer can't support this kind of spi registers well.
remove cache support and read/write registers directly
Signed-off-by: Scott Jiang <scott.jiang.linux@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Scott Jiang [Fri, 12 Aug 2011 22:04:13 +0000 (18:04 -0400)]
ASoC: Add spi hw read function for 16 addr 8 data mode for ad193x fix
[This will be used by the ad193x driver to fix the fact that the
original author of the driver put a bodge for their particular chip into
a the generic ASoC register I/O abstraction layer which looked like an
obvious bug which ended up getting fixed in 3.0. Sadly there were no
comments documenting what was going on. A minimally invasive correction
to the driver is to remove the register cache support and go direct to
the hardware all the time so we're adding a new feature -- broonie]
Signed-off-by: Scott Jiang <scott.jiang.linux@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Scott Jiang [Fri, 12 Aug 2011 22:04:12 +0000 (18:04 -0400)]
ASoC: ad193x: fix system clock
system clock is 24.576MHz instead of 12.288MHz
Signed-off-by: Scott Jiang <scott.jiang.linux@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Scott Jiang [Fri, 12 Aug 2011 22:04:11 +0000 (18:04 -0400)]
ASoC: ad193x: fix dac word len setting
dac word len value should left shift before setting
Signed-off-by: Scott Jiang <scott.jiang.linux@gmail.com>
Acked-by: Barry Song <21cnbao@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@kernel.org
Scott Jiang [Fri, 12 Aug 2011 22:04:10 +0000 (18:04 -0400)]
ASoC: ad193x: fix registers definition
fix dac word len mask and adc tdm fmt shift value
Signed-off-by: Scott Jiang <scott.jiang.linux@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@kernel.org
Axel Lin [Sat, 13 Aug 2011 03:33:08 +0000 (11:33 +0800)]
ASoC: sta32x: Fix a memory leak if snd_soc_register_codec fails
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Axel Lin [Sat, 13 Aug 2011 11:15:01 +0000 (19:15 +0800)]
ASoC: soc-jack: Fix checking return value of request_any_context_irq
request_any_context_irq() returns a negative value on failure.
On success, it returns either IRQC_IS_HARDIRQ or IRQC_IS_NESTED.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@kernel.orG
Mark Brown [Sun, 14 Aug 2011 10:24:40 +0000 (19:24 +0900)]
Merge branch 'for-3.1' into for-3.2
Vasily Khoruzhick [Fri, 12 Aug 2011 14:53:00 +0000 (17:53 +0300)]
ASoC: rx1950: Fix compilation error due to missing header
Add linux/types.h to fix this compilation error:
In file included from arch/arm/mach-s3c2410/include/mach/gpio-fns.h:27:0,
from arch/arm/mach-s3c2410/include/mach/gpio.h:27,
from /home/anarsoul/work/pda-linux/linux-next/arch/arm/include/asm/gpio.h:5,
from include/linux/gpio.h:18,
from sound/soc/samsung/rx1950_uda1380.c:20:
arch/arm/plat-samsung/include/plat/gpio-cfg.h:29:34: error: expected ‘=’, ‘,’, ‘;’, ‘asm’ or ‘__attribute__’ before ‘s3c_gpio_pull_t’
arch/arm/plat-samsung/include/plat/gpio-cfg.h:30:34: error: expected ‘=’, ‘,’, ‘;’, ‘asm’ or ‘__attribute__’ before ‘s5p_gpio_drvstr_t’
arch/arm/plat-samsung/include/plat/gpio-cfg.h:57:2: error: expected specifier-qualifier-list before ‘s3c_gpio_pull_t’
arch/arm/plat-samsung/include/plat/gpio-cfg.h:148:47: error: expected declaration specifiers or ‘...’ before ‘s3c_gpio_pull_t’
arch/arm/plat-samsung/include/plat/gpio-cfg.h:156:24: error: expected ‘=’, ‘,’, ‘;’, ‘asm’ or ‘__attribute__’ before ‘s3c_gpio_getpull’
arch/arm/plat-samsung/include/plat/gpio-cfg.h:175:24: error: expected declaration specifiers or ‘...’ before ‘s3c_gpio_pull_t’
arch/arm/plat-samsung/include/plat/gpio-cfg.h: In function ‘s3c_gpio_cfgrange_nopull’:
arch/arm/plat-samsung/include/plat/gpio-cfg.h:180:47: error: ‘s3c_gpio_pull_t’ undeclared (first use in this function)
arch/arm/plat-samsung/include/plat/gpio-cfg.h:180:47: note: each undeclared identifier is reported only once for each function it appears in
arch/arm/plat-samsung/include/plat/gpio-cfg.h:180:47: error: expected ‘)’ before numeric constant
arch/arm/plat-samsung/include/plat/gpio-cfg.h:180:47: error: too many arguments to function ‘s3c_gpio_cfgall_range’
arch/arm/plat-samsung/include/plat/gpio-cfg.h:174:12: note: declared here
arch/arm/plat-samsung/include/plat/gpio-cfg.h: At top level:
arch/arm/plat-samsung/include/plat/gpio-cfg.h:199:26: error: expected ‘=’, ‘,’, ‘;’, ‘asm’ or ‘__attribute__’ before ‘s5p_gpio_get_drvstr’
arch/arm/plat-samsung/include/plat/gpio-cfg.h:210:50: error: expected declaration specifiers or ‘...’ before ‘s5p_gpio_drvstr_t’
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Acked-by: Jassi Brar <jassisinghbrar@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Vasily Khoruzhick [Fri, 12 Aug 2011 14:52:59 +0000 (17:52 +0300)]
ASoC: h1940: Fix compilation error due to missing header
Add linux/types.h to fix this compilation error:
In file included from arch/arm/mach-s3c2410/include/mach/gpio-fns.h:27:0,
from arch/arm/mach-s3c2410/include/mach/gpio.h:27,
from /home/anarsoul/work/pda-linux/linux-next/arch/arm/include/asm/gpio.h:5,
from include/linux/gpio.h:18,
from sound/soc/samsung/rx1950_uda1380.c:20:
arch/arm/plat-samsung/include/plat/gpio-cfg.h:29:34: error: expected ‘=’, ‘,’, ‘;’, ‘asm’ or ‘__attribute__’ before ‘s3c_gpio_pull_t’
arch/arm/plat-samsung/include/plat/gpio-cfg.h:30:34: error: expected ‘=’, ‘,’, ‘;’, ‘asm’ or ‘__attribute__’ before ‘s5p_gpio_drvstr_t’
arch/arm/plat-samsung/include/plat/gpio-cfg.h:57:2: error: expected specifier-qualifier-list before ‘s3c_gpio_pull_t’
arch/arm/plat-samsung/include/plat/gpio-cfg.h:148:47: error: expected declaration specifiers or ‘...’ before ‘s3c_gpio_pull_t’
arch/arm/plat-samsung/include/plat/gpio-cfg.h:156:24: error: expected ‘=’, ‘,’, ‘;’, ‘asm’ or ‘__attribute__’ before ‘s3c_gpio_getpull’
arch/arm/plat-samsung/include/plat/gpio-cfg.h:175:24: error: expected declaration specifiers or ‘...’ before ‘s3c_gpio_pull_t’
arch/arm/plat-samsung/include/plat/gpio-cfg.h: In function ‘s3c_gpio_cfgrange_nopull’:
arch/arm/plat-samsung/include/plat/gpio-cfg.h:180:47: error: ‘s3c_gpio_pull_t’ undeclared (first use in this function)
arch/arm/plat-samsung/include/plat/gpio-cfg.h:180:47: note: each undeclared identifier is reported only once for each function it appears in
arch/arm/plat-samsung/include/plat/gpio-cfg.h:180:47: error: expected ‘)’ before numeric constant
arch/arm/plat-samsung/include/plat/gpio-cfg.h:180:47: error: too many arguments to function ‘s3c_gpio_cfgall_range’
arch/arm/plat-samsung/include/plat/gpio-cfg.h:174:12: note: declared here
arch/arm/plat-samsung/include/plat/gpio-cfg.h: At top level:
arch/arm/plat-samsung/include/plat/gpio-cfg.h:199:26: error: expected ‘=’, ‘,’, ‘;’, ‘asm’ or ‘__attribute__’ before ‘s5p_gpio_get_drvstr’
arch/arm/plat-samsung/include/plat/gpio-cfg.h:210:50: error: expected declaration specifiers or ‘...’ before ‘s5p_gpio_drvstr_t’
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Acked-by: Jassi Brar <jassisinghbrar@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Mark Brown [Sat, 13 Aug 2011 02:50:48 +0000 (11:50 +0900)]
ASoC: Support !CONFIG_REGMAP builds
Since we changed regmap to be selected and register per bus rather than
via the core only we can't rely on it being enabled by the ASoC core.
Support compiling it out.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Reported-by: Axel Lin <axel.lin@gmail.com>
Mark Brown [Sun, 14 Aug 2011 10:19:58 +0000 (19:19 +0900)]
Merge branch 'for-3.1' into for-3.2
Mark Brown [Wed, 3 Aug 2011 09:22:28 +0000 (18:22 +0900)]
ASoC: Remove redundant -codec from WM8750
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Mark Brown [Thu, 4 Aug 2011 04:23:38 +0000 (13:23 +0900)]
ASoC: Move WM8962 CLKREG_OVD earlier
When the clocking registers are not overriden some of the registers are
not writable.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Cc: stable@kernel.org
Mark Brown [Wed, 10 Aug 2011 08:47:33 +0000 (17:47 +0900)]
ASoC: Disable WM8994 VMID for digital only paths
On WM8994 class devices only the analogue portions of the CODEC require
VMID so when running digital only paths we can leave VMID disabled.
On some earlier devices the FLL uses VMID so we don't use DAPM reference
counting alone, we maintain an internal reference count which is also
enabled and disabled by the FLL startup.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Mark Brown [Fri, 15 Jul 2011 06:12:31 +0000 (15:12 +0900)]
ASoC: Add VMID widget for wm_hubs devices
Currently this does not actually do anything, it is being introduced in
order to facilitate additional power optimisations for current generation
devices.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Mark Brown [Mon, 8 Aug 2011 03:44:27 +0000 (12:44 +0900)]
ASoC: Add device tree binding for WM8753
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Mark Brown [Wed, 3 Aug 2011 08:34:59 +0000 (17:34 +0900)]
ASoC: Add device tree binding for WM8750
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Mark Brown [Wed, 3 Aug 2011 07:53:22 +0000 (16:53 +0900)]
ASoC: Add device tree binding for WM8737
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Mark Brown [Wed, 3 Aug 2011 07:53:02 +0000 (16:53 +0900)]
ASoC: Add device tree binding for WM8728
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Mark Brown [Wed, 3 Aug 2011 07:52:47 +0000 (16:52 +0900)]
ASoC: Add device tree binding for WM8711
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Mark Brown [Tue, 2 Aug 2011 04:22:36 +0000 (13:22 +0900)]
ASoC: Add device tree support for WM8580
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Mark Brown [Tue, 2 Aug 2011 04:08:13 +0000 (13:08 +0900)]
ASoC: Add device tree binding for WM8523
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Mark Brown [Tue, 2 Aug 2011 04:03:04 +0000 (13:03 +0900)]
ASoC: Add device tree binding for WM8510
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Takashi Iwai [Fri, 12 Aug 2011 16:22:10 +0000 (18:22 +0200)]
ASoC: Fix compile warning in wm8750.c
sound/soc/codecs/wm8750.c:784:2: warning: missing braces around initializer
sound/soc/codecs/wm8750.c:784:2: warning: (near initialization for ‘wm8750_spi_ids[2].name’)
It's because struct spi_device_id.name is a char array, not a pointer,
while the driver initializes explicitly with 0.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Mark Brown [Wed, 10 Aug 2011 10:25:40 +0000 (19:25 +0900)]
ASoC: Add bitfield definitions for WM8958 MICBIAS registers
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Stephen Warren [Thu, 11 Aug 2011 17:59:11 +0000 (11:59 -0600)]
ASoC: soc-io: Fix CONFIG_REGMAP_I2C/SPI guards to support regmap modules
When CONFIG_REGMAP_I2C/SPI are m, CONFIG_REGMAP_I2C_MODULE is set in the
pre-processor instead of CONFIG_REGMAP_I2C. This removes SND_SOC_I2C as a
valid option for snd_soc_codec_set_cache_io()'s control parameter, and
causes any ASoC regmap-using codec built as a module to fail to initialize.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Mark Brown [Thu, 4 Aug 2011 09:13:45 +0000 (18:13 +0900)]
ASoC: Allow userspace control of Speyside headphone output
In order to facilitate the widest range of use cases (especially things
like speakerphone) allow the headphone output to be enabled and disabled
by the application layer.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Mark Brown [Fri, 12 Aug 2011 02:48:29 +0000 (11:48 +0900)]
Merge branch 'for-3.1' into for-3.2
Jarkko Nikula [Thu, 11 Aug 2011 12:44:57 +0000 (15:44 +0300)]
ASoC: omap: Update e-mail address of Jarkko Nikula
My gmail account got disabled and I'm not going to reopen it.
Signed-off-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Axel Lin [Thu, 11 Aug 2011 14:19:16 +0000 (22:19 +0800)]
ASoC: sgtl5000: fix module device table type for sgtl5000_dt_ids
The module device table for of_device_id should use "of" type.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Sangbeom Kim [Wed, 20 Jul 2011 08:07:13 +0000 (17:07 +0900)]
ASoC: SAMSUNG: Add I2S0 internal dma driver
I2S in Exynos4 and S5PC110(S5PV210) has a internal dma.
It can be used low power audio mode and 2nd channel transfer.
This patch can support idma.
[Reapplied after dependencies propagated through in 3.1-rc1. --broonie]
Signed-off-by: Sangbeom Kim <sbkim73@samsung.com>
Acked-by: Jassi Brar <jassisinghbrar@gmail.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Acked-by: Jassi Brar <jassisinghbrar@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Mark Brown [Thu, 11 Aug 2011 03:30:26 +0000 (12:30 +0900)]
Merge branch 'for-3.1' into for-3.2
Mark Brown [Thu, 11 Aug 2011 03:23:22 +0000 (12:23 +0900)]
ASoC: Terminate WM8750 SPI device ID table
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Mark Brown [Thu, 11 Aug 2011 01:43:40 +0000 (10:43 +0900)]
Merge branch 'for-3.1' into for-3.2
Mark Brown [Wed, 10 Aug 2011 13:19:19 +0000 (22:19 +0900)]
ASoC: Add missing break in WM8994 probe
This error would have no effect on current silicon revisions, the fall
through case has the same behaviour.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Axel Lin [Wed, 10 Aug 2011 08:24:12 +0000 (16:24 +0800)]
ASoC: soc-io: Add CONFIG_REGMAP_I2C/CONFIG_REGMAP_SPI guards for regmap_init_i2c/regmap_init_spi
In the case of "make da8xx_omapl_defconfig;make", the SPI support is disabled.
Thus calling regmap_init_spi in soc-io.c has below build error.
ERROR: "regmap_init_spi" [sound/soc/snd-soc-core.ko] undefined!
make[1]: *** [__modpost] Error 1
make: *** [modules] Error 2
This patch fixes the build error by adding CONFIG_REGMAP_I2C/CONFIG_REGMAP_SPI
guards for regmap_init_i2c/regmap_init_spi.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Mark Brown [Wed, 10 Aug 2011 05:20:09 +0000 (14:20 +0900)]
ASoC: Specify register defaults for WM8958 MICBIAS1 and MICBIAS2
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Mark Brown [Wed, 10 Aug 2011 05:11:48 +0000 (14:11 +0900)]
Merge branch 'for-3.1' into for-3.2
Mark Brown [Wed, 10 Aug 2011 00:41:26 +0000 (09:41 +0900)]
ASoC: Fix typo in wm8750 spi_ids
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Mark Brown [Fri, 29 Jul 2011 15:27:18 +0000 (16:27 +0100)]
ASoC: Fix warning in WM1250-EV1 driver
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Mark Brown [Wed, 3 Aug 2011 08:30:57 +0000 (17:30 +0900)]
ASoC: Add SPI support for WM8741
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Mark Brown [Wed, 3 Aug 2011 08:16:11 +0000 (17:16 +0900)]
ASoC: Refactor WM8741 regulator handling into CODEC generic code
No meaningful runtime impact but is more in line with other CODECs and
will support further work.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Mark Brown [Tue, 9 Aug 2011 15:18:10 +0000 (00:18 +0900)]
Merge branch 'for-3.1' into for-3.2
Mark Brown [Wed, 3 Aug 2011 07:52:10 +0000 (16:52 +0900)]
ASoC: Remove some more redundant -codecs from driver names
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Mark Brown [Wed, 3 Aug 2011 08:34:41 +0000 (17:34 +0900)]
ASoC: Update SMDKs for WM8580 -codec removal
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Mark Brown [Thu, 4 Aug 2011 01:54:17 +0000 (10:54 +0900)]
ASoC: Fix warning in Speyside WM8962
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Mark Brown [Wed, 3 Aug 2011 09:32:09 +0000 (18:32 +0900)]
ASoC: Fix SPI driver binding for WM8987
As we had no id_table only the driver name would be matched against
meaning that WM8987 devices wouldn't be bound.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Mark Brown [Wed, 3 Aug 2011 08:36:48 +0000 (17:36 +0900)]
ASoC: Fix binding of WM8750 on Jive
The I2C address is misformatted and would never match.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Cc: stable@kernel.org
Mark Brown [Tue, 9 Aug 2011 01:00:05 +0000 (10:00 +0900)]
Merge branch 'for-3.1' into for-3.2
Mark Brown [Mon, 8 Aug 2011 03:44:02 +0000 (12:44 +0900)]
ASoC: Remove unneeded -codec from WM8753 driver name
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Stephen Warren [Thu, 4 Aug 2011 22:44:44 +0000 (16:44 -0600)]
ASoC: WM8903: Free IRQ on device removal
Without this, request_irq on subsequent device initialization fails, and
the codec cannot be used.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Stephen Warren [Thu, 4 Aug 2011 22:44:43 +0000 (16:44 -0600)]
ASoC: Tegra: wm8903 machine driver: Allow re-insertion of module
Two issues were preventing module snd-soc-tegra-wm8903.ko from being
removed and re-inserted:
a) The speaker-enable GPIO is hosted by the WM8903 chip. This GPIO must
be freed before snd_soc_unregister_card() is called, because that
triggers wm8903.c:wm8903_remove(), which calls gpiochip_remove(), which
then fails if any of the GPIOs are in use. To solve this, free all GPIOs
first, so the code doesn't care where they come from.
b) We need to call snd_soc_jack_free_gpios() to match the call to
snd_soc_jack_add_gpios() during initialization. Without this, the
call to snd_soc_jack_add_gpios() fails during any subsequent modprobe
and initialization, since the GPIO and IRQ are already registered. In
turn, this causes the headphone state not to be monitored, so the
headphone is assumed not to be plugged in, and the audio path to it is
never enabled.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Cc: stable@kernel.org
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Stephen Warren [Thu, 4 Aug 2011 22:44:42 +0000 (16:44 -0600)]
ASoC: Tegra: tegra_pcm_deallocate_dma_buffer: Don't OOPS
Not all PCM devices have all sub-streams. Specifically, the SPDIF driver
only supports playback and hence has no capture substream. Check whether
a substream exists before dereferencing it, when de-allocating DMA
buffers in tegra_pcm_deallocate_dma_buffer.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@kernel.org
Mark Brown [Tue, 9 Aug 2011 00:39:55 +0000 (09:39 +0900)]
Merge branch 'fix/asoc' of git://git./linux/kernel/git/tiwai/sound-2.6 into for-3.1
Takashi Iwai [Mon, 8 Aug 2011 08:45:31 +0000 (10:45 +0200)]
Merge branch 'wm8996-rename' of git://git./linux/kernel/git/broonie/sound-2.6 into fix/asoc
Mark Brown [Mon, 8 Aug 2011 06:00:13 +0000 (15:00 +0900)]
Merge branch 'regmap-asoc' into for-3.2
Mark Brown [Sun, 24 Jul 2011 11:23:37 +0000 (12:23 +0100)]
ASoC: Add regmap as a control type
Allow drivers to set up their own regmap API structures. This is mainly
useful with MFDs where the core driver will have set up regmap at the
minute, though it may make sense to push the existing regmap setup out
of the core into the drivers.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Mark Brown [Mon, 13 Jun 2011 18:35:29 +0000 (19:35 +0100)]
ASoC: Use new register map API for ASoC generic physical I/O
Remove all the ASoC specific physical I/O code and replace it with calls
into the regmap API. The bulk write code can only be used safely if all
regmap calls are locked with the CODEC lock, we need to add bulk support
to the regmap API or replace the code with an open coded loop (though
currently it has no users...).
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Mark Brown [Mon, 8 Aug 2011 05:56:19 +0000 (14:56 +0900)]
Merge branch 'for-3.1' into for-3.2
Conflict due to the fix for the register map failure - taken the for-3.1
version.
Conflicts:
sound/soc/codecs/sgtl5000.c
Mark Brown [Mon, 8 Aug 2011 05:52:01 +0000 (14:52 +0900)]
Merge branch 'for-3.1' of git://git./linux/kernel/git/broonie/sound-2.6.git into for-3.1
Mark Brown [Wed, 20 Jul 2011 12:49:58 +0000 (13:49 +0100)]
ASoC: Acknowledge WM8996 interrupts before acting on them
This closes the small race between a status being read in response to an
interrupt and clearing the interrupt, meaning that if the status changes
between those periods we might not get a reassertion of the interrupt.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Mark Brown [Fri, 24 Jun 2011 11:10:44 +0000 (12:10 +0100)]
ASoC: Rename WM8915 to WM8996
For marketing reasons the part will be called WM8996. In order to avoid
user confusion rename the driver to reflect this.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Linus Torvalds [Mon, 8 Aug 2011 01:23:30 +0000 (18:23 -0700)]
Linux 3.1-rc1
Linus Torvalds [Sun, 7 Aug 2011 22:52:19 +0000 (15:52 -0700)]
Merge git://git./linux/kernel/git/davem/sparc
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc:
sparc: Fix build with DEBUG_PAGEALLOC enabled.
Rafael J. Wysocki [Sun, 7 Aug 2011 22:26:50 +0000 (00:26 +0200)]
sh: Fix boot crash related to SCI
Commit
d006199e72a9 ("serial: sh-sci: Regtype probing doesn't need to be
fatal.") made sci_init_single() return when sci_probe_regmap() succeeds,
although it should return when sci_probe_regmap() fails. This causes
systems using the serial sh-sci driver to crash during boot.
Fix the problem by using the right return condition.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Sun, 7 Aug 2011 22:49:11 +0000 (15:49 -0700)]
arm: remove stale export of 'sha_transform'
The generic library code already exports the generic function, this was
left-over from the ARM-specific version that just got removed.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Sun, 7 Aug 2011 21:07:03 +0000 (14:07 -0700)]
arm: remove "optimized" SHA1 routines
Since commit
1eb19a12bd22 ("lib/sha1: use the git implementation of
SHA-1"), the ARM SHA1 routines no longer work. The reason? They
depended on the larger 320-byte workspace, and now the sha1 workspace is
just 16 words (64 bytes). So the assembly version would overwrite the
stack randomly.
The optimized asm version is also probably slower than the new improved
C version, so there's no reason to keep it around. At least that was
the case in git, where what appears to be the same assembly language
version was removed two years ago because the optimized C BLK_SHA1 code
was faster.
Reported-and-tested-by: Joachim Eastwood <manabian@gmail.com>
Cc: Andreas Schwab <schwab@linux-m68k.org>
Cc: Nicolas Pitre <nico@fluxnic.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Al Viro [Sun, 7 Aug 2011 17:55:11 +0000 (18:55 +0100)]
fix rcu annotations noise in cred.h
task->cred is declared as __rcu, and access to other tasks' ->cred is,
indeed, protected. Access to current->cred does not need rcu_dereference()
at all, since only the task itself can change its ->cred. sparse, of
course, has no way of knowing that...
Add force-cast in current_cred(), make current_fsuid() et.al. use it.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
projects / GitHub / exynos8895 / android_kernel_samsung_universal8895.git / log