git.stricted.de - GitHub/LineageOS/G12/android_kernel_amlogic

skd: Fix checkpatch ERRORS and removed unused functions

This patch fixes checkpatch.pl errors for assignment in if condition.
It also removes unused readq / readl function calls.

As Andrew had disabled the compilation of drivers for 32 bit,
I have modified format specifiers in few VPRINTKs to avoid warnings
during 64 bit compilation.

Signed-off-by: Akhil Bhansali <abhansali@stec-inc.com>
Reviewed-by: Ramprasad Chinthekindi <rchinthekindi@stec-inc.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>

rsxx: Fix possible kernel panic with invalid config.

This patch fixes a possible Kernel Panic on driver load if
the configuration on the card is messed up or not yet set.
The driver could possible give a 32 bit unsigned all Fs to
the kernel as the device's block size.

Now we only write the block size to the kernel if the
configuration from the card is valid.

Also, driver version is being updated.

Signed-off-by: Philip J Kelleher <pjk1939@linux.vnet.ibm.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>

rsxx: Disallow discards from being unmapped.

This patch fixes a bug in which discards were always
calling pci_unmap_page. Discards should never call the
pci_unmap_page function call because they are never mapped.

This caused a race condition on PowerPC systems when issuing
discards, writes, and reads all at the same time. The
pci_map_page function would eventually map logical address
0 for a read or write. Discards are always assigned a DMA
address of 0 because they are never mapped. So if
pci_map_page mapped address 0 for a DMA and a discard was
"unmapped" then the address would be freed and would cause
an EEH event to occur when Hardware accesses the address.

This was injected/uncovered in commit:
b347f9cf0bc8d42ee95ba1d3837fd93045ab336b

The pci_dma_mapping_error function declares -1 a DMA_ERROR
not 0 like initially thought So before we would never unmap
discards because they were considered NULL.

This patch should fall on top of commit id:
fc1967bb08a6184ed44ef990e1dd4389901b809c

Also, the driver version is being up dated.

Signed-off-by: Philip J Kelleher <pjk1939@linux.vnet.ibm.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>

drbd: avoid to shrink max_bio_size due to peer re-configuration

For a long time, the receiving side has spread "too large" incoming
requests over multiple bios. No need to shrink our max_bio_size
(max_hw_sectors) if the peer is reconfigured to use a different storage.

The problem manifests itself if we are not the top of the device stack
(DRBD is used a LVM PV).

A hardware reconfiguration on the peer may cause the supported
max_bio_size to shrink, and the connection handshake would now
unnecessarily shrink the max_bio_size on the active node.

There is no way to notify upper layers that they have to "re-stack"
their limits. So they won't notice at all, and may keep submitting bios
that are suddenly considered "too large for device".

We already check for compatibility and ignore changes on the peer,
the code only was masked out unless we have a fully established connection.
We just need to allow it a bit earlier during the handshake.

Also consider max_hw_sectors in our merge bvec function, just in case.

Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>

drbd: fix decoding of bitmap vli rle for device sizes > 64 TB

Symptoms: disconnect after bitmap exchange due to
bitmap overflow (e:49731075554) while decoding bm RLE packet

In the decoding step of the variable length integer run length encoding
there was potentially an uncatched bitshift by wordsize (variable >> 64).

The result of which is "undefined" :(
(only "sometimes" the result is the desired 0)

Fix: don't do any bit shift magic for shift == 64, just assign.

Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>

drbd: Fix adding of new minors with freshly created meta data

Online adding of new minors with freshly created meta data
to an resource with an established connection failed, with a
wrong state transition on one side on one side of the new minor.

Freshly created meta-data has a la_size (last agreed size) of 0.
When we online add such devices, the code wrongly got into
the code path for resyncing new storage that was added while
the disk was detached.

Fixed that by making the GREW from ZERO a special case.

Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>

drbd: Fix an connection drop issue after enabling allow-two-primaries

Since drbd-8.4.0 it is possible to change the allow-two-primaries
network option while the connection is established.

The sequence code used to partially order packets from the
data socket with packets from the meta-data socket, still assued
that the allow-two-primaries option is constant while the
connection is established.

I.e.
On a node that has the RESOLVE_CONFLICTS bits set, after enabling
allow-two-primaries, when receiving the next data packet it timed out
while waiting for the necessary packets on the data socket to arrive
(wait_for_and_update_peer_seq() function).

Fixed that by always tracking the sequence number, but only waiting
for it if allow-two-primaries is set.

Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>

drbd: fix NULL pointer deref in module init error path

If we want to iterate over the (as of yet still empty) list in the
cleanup path, we need to initialize the list before the first goto fail.

Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>

block: disable cpqarray in Kconfig

Mike writes:

"cpqarray hasn't been used in over 12 years. It's doubtful that anyone
still uses the board. It's time the driver was removed from the mainline
kernel. The only updates these days are minor and mostly done by people
outside of HP."

If nobody yells, we'll remove it from the kernel tree completely
for 3.15.

Signed-off-by: Jens Axboe <axboe@kernel.dk>

Add support for sTec's pci-e flash card Kronos

Signed-off-by: Akhil Bhansali <abhansali@stec-inc.com>
Signed-off-by: Ramprasad Chinthekindi <rchinthekindi@stec-inc.com>
Reviewed-by: Jeff Moyer <jmoyer@redhat.com>
Folded patch, contributions to clean up this driver from:

Jens Axboe
Dan Carpenter
Andrew Morton

Signed-off-by: Jens Axboe <axboe@kernel.dk>

rsxx: Kernel Panic caused by mapping Discards

This fixes a kernel panic injected by commit id
8d26750143341831bc312f61c5ed141eeb75b8d0 where discards
are getting mapped through the pci_map_page function call.

The driver will now start verifying that a dma is not a
discard before issuing a the pci_map_page function call.

Also, we are updating the driver version.

Signed-off-by: Philip J Kelleher <pjk1939@linux.vnet.ibm.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>

mtip32xx: dynamically allocate buffer in debugfs functions

Dynamically allocate buf to prevent warnings:

drivers/block/mtip32xx/mtip32xx.c: In function ‘mtip_hw_read_device_status’:
drivers/block/mtip32xx/mtip32xx.c:2823: warning: the frame size of 1056 bytes is larger than 1024 bytes
drivers/block/mtip32xx/mtip32xx.c: In function ‘mtip_hw_read_registers’:
drivers/block/mtip32xx/mtip32xx.c:2894: warning: the frame size of 1056 bytes is larger than 1024 bytes
drivers/block/mtip32xx/mtip32xx.c: In function ‘mtip_hw_read_flags’:
drivers/block/mtip32xx/mtip32xx.c:2917: warning: the frame size of 1056 bytes is larger than 1024 bytes

Signed-off-by: David Milburn <dmilburn@redhat.com>
Acked-by: Asai Thambi S P <asamymuthupa@micron.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>

mtip32xx: Add SRSI support

This patch add support for SRSI(Surprise Removal Surprise Insertion).

Approach:
---------
Surprise Removal:
-----------------
On surprise removal of the device, gendisk, request queue, device index, sysfs
entries, etc are retained as long as device is in use - mounted filesystem,
device opened by an application, etc. The service thread breaks out of the main
while loop, waits for pci remove to exit, and then waits for device to become
free. When there no holders of the device, service thread cleans up the block
and device related stuff and returns.

Surprise Insertion:
-------------------
No change, this scenario follows the normal pci probe() function flow.

Signed-off-by: Asai Thambi S P <asamymuthupa@micron.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>

rsxx: Moving pci_map_page to prevent overflow.

The pci_map_page function has been moved into our
issued workqueue to prevent an us running out of
mappable addresses on non-HWWD PCIe x8 slots. The
maximum amount that can possible be mapped at one
time now is: 255 dmas X 4 dma channels X 4096 Bytes.

Signed-off-by: Philip J Kelleher <pjk1939@linux.vnet.ibm.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>

rsxx: Handling failed pci_map_page on PowerPC and double free.

The rsxx driver was not checking the correct value during a
pci_map_page failure. Fixing this also uncovered a
double free if the bio was returned before it was
broken up into indiviadual 4k dmas, that is also
fixed here.

Signed-off-by: Philip J Kelleher <pjk1939@linux.vnet.ibm.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>

loop: fix crash when using unassigned loop device

When the loop module is loaded, it creates 8 loop devices /dev/loop[0-7].
The devices have no request routine and thus, when they are used without
being assigned, a crash happens.

For example, these commands cause crash (assuming there are no used loop
devices):

Kernel Fault: Code=26 regs=000000007f420980 (Addr=0000000000000010)
CPU: 1 PID: 50 Comm: kworker/1:1 Not tainted 3.11.0 #1
Workqueue: ksnaphd do_metadata [dm_snapshot]
task: 000000007fcf4078 ti: 000000007f420000 task.ti: 000000007f420000
[  116.319988]
     YZrvWESTHLNXBCVMcbcbcbcbOGFRQPDI
PSW: 00001000000001001111111100001111 Not tainted
r00-03  000000ff0804ff0f 00000000408bf5d0 00000000402d8204 000000007b7ff6c0
r04-07  00000000408a95d0 000000007f420950 000000007b7ff6c0 000000007d06c930
r08-11  000000007f4205c0 0000000000000001 000000007f4205c0 000000007f4204b8
r12-15  0000000000000010 0000000000000000 0000000000000000 0000000000000000
r16-19  000000001108dd48 000000004061cd7c 000000007d859800 000000000800000f
r20-23  0000000000000000 0000000000000008 0000000000000000 0000000000000000
r24-27  00000000ffffffff 000000007b7ff6c0 000000007d859800 00000000408a95d0
r28-31  0000000000000000 000000007f420950 000000007f420980 000000007f4208e8
sr00-03  0000000000000000 0000000000000000 0000000000000000 0000000000303000
sr04-07  0000000000000000 0000000000000000 0000000000000000 0000000000000000
[  117.549988]
IASQ: 0000000000000000 0000000000000000 IAOQ: 00000000402d82fc 00000000402d8300
IIR: 53820020    ISR: 0000000000000000  IOR: 0000000000000010
CPU:        1   CR30: 000000007f420000 CR31: ffffffffffffffff
ORIG_R28: 0000000000000001
IAOQ[0]: generic_make_request+0x11c/0x1a0
IAOQ[1]: generic_make_request+0x120/0x1a0
RP(r2): generic_make_request+0x24/0x1a0
Backtrace:
[<00000000402d83f0>] submit_bio+0x70/0x140
[<0000000011087c4c>] dispatch_io+0x234/0x478 [dm_mod]
[<0000000011087f44>] sync_io+0xb4/0x190 [dm_mod]
[<00000000110883bc>] dm_io+0x2c4/0x310 [dm_mod]
[<00000000110bfcd0>] do_metadata+0x28/0xb0 [dm_snapshot]
[<00000000401591d8>] process_one_work+0x160/0x460
[<0000000040159bc0>] worker_thread+0x300/0x478
[<0000000040161a70>] kthread+0x118/0x128
[<0000000040104020>] end_fault_vector+0x20/0x28
[<0000000040177220>] task_tick_fair+0x420/0x4d0
[<00000000401aa048>] invoke_rcu_core+0x50/0x60
[<00000000401ad5b8>] rcu_check_callbacks+0x210/0x8d8
[<000000004014aaa0>] update_process_times+0xa8/0xc0
[<00000000401ab86c>] rcu_process_callbacks+0x4b4/0x598
[<0000000040142408>] __do_softirq+0x250/0x2c0
[<00000000401789d0>] find_busiest_group+0x3c0/0xc70
[  119.379988]
Kernel panic - not syncing: Kernel Fault
Rebooting in 1 seconds..

Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Cc: stable@kernel.org
Signed-off-by: Jens Axboe <axboe@kernel.dk>

xen/blkback: fix reference counting

If the permission check fails, we drop a reference to the blkif without
having taken it in the first place. The bug was introduced in commit
604c499cbbcc3d5fe5fb8d53306aa0fae1990109 (xen/blkback: Check device
permissions before allowing OP_DISCARD).

Cc: stable@vger.kernel.org
Cc: Jan Beulich <JBeulich@suse.com>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: Vegard Nossum <vegard.nossum@oracle.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>

xen-blkfront: improve aproximation of required grants per request

Improve the calculation of required grants to process a request by
using nr_phys_segments instead of always assuming a request is going
to use all posible segments.

nr_phys_segments contains the number of scatter-gather DMA addr+len
pairs, which is basically what we put at every granted page.
for_each_sg iterates over the DMA addr+len pairs and uses a grant
page for each of them.

Signed-off-by: Roger Pau Monné <roger.pau@citrix.com>
Reviewed-by: David Vrabel <david.vrabel@citrix.com>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: David Vrabel <david.vrabel@citrix.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>

xen-blkfront: revoke foreign access for grants not mapped by the backend

There's no need to keep the foreign access in a grant if it is not
persistently mapped by the backend. This allows us to free grants that
are not mapped by the backend, thus preventing blkfront from hoarding
all grants.

The main effect of this is that blkfront will only persistently map
the same grants as the backend, and it will always try to use grants
that are already mapped by the backend. Also the number of persistent
grants in blkfront is the same as in blkback (and is controlled by the
value in blkback).

Signed-off-by: Roger Pau Monné <roger.pau@citrix.com>
Reviewed-by: David Vrabel <david.vrabel@citrix.com>
Acked-by: Matt Wilson <msw@amazon.com>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: David Vrabel <david.vrabel@citrix.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>

mg_disk: remove deprecated IRQF_DISABLED

This patch proposes to remove the use of the IRQF_DISABLED flag

It's a NOOP since 2.6.35 and it will be removed one day.

Signed-off-by: Michael Opdenacker <michael.opdenacker@free-electrons.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>

block: replace IS_ERR and PTR_ERR with PTR_ERR_OR_ZERO

This patch fixes coccinelle error regarding usage of IS_ERR and
PTR_ERR instead of PTR_ERR_OR_ZERO.

Signed-off-by: Duan Jiong <duanj.fnst@cn.fujitsu.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>

block: Do not call sector_div() with a 64-bit divisor

do_div() (called by sector_div() if CONFIG_LBDAF=y) is meant for divisions
of 64-bit number by 32-bit numbers.  Passing 64-bit divisor types caused
issues in the past on 32-bit platforms, cfr. commit
ea077b1b96e073eac5c3c5590529e964767fc5f7 ("m68k: Truncate base in
do_div()").

As queue_limits.max_discard_sectors and .discard_granularity are unsigned
int, max_discard_sectors and granularity should be unsigned int.
As bdev_discard_alignment() returns int, alignment should be int.
Now 2 calls to sector_div() can be replaced by 32-bit arithmetic:
  - The 64-bit modulo operation can become a 32-bit modulo operation,
  - The 64-bit division and multiplication can be replaced by a 32-bit
    modulo operation and a subtraction.

Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>

kernel: trace: blktrace: remove redundent memcpy() in compat_blk_trace_setup()

do_blk_trace_setup() will fully initialize 'buts.name', so can remove
the related memcpy(). And also use BLKTRACE_BDEV_SIZE and ARRAY_SIZE
instead of hard code number '32'.

Signed-off-by: Chen Gang <gang.chen@asianux.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>

block: Consolidate duplicated bio_trim() implementations

Someone cut and pasted md's md_trim_bio() into xen-blkfront.c. Come on,
we should know better than this.

Signed-off-by: Kent Overstreet <kmo@daterainc.com>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Neil Brown <neilb@suse.de>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: Jeremy Fitzhardinge <jeremy@goop.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>

block: Use rw_copy_check_uvector()

No need for silly open coding - and struct sg_iovec has exactly the same
layout as struct iovec...

Signed-off-by: Kent Overstreet <kmo@daterainc.com>
Cc: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Jens Axboe <axboe@kernel.dk>

block: Enable sysfs nomerge control for I/O requests in the plug list

This patch enables the sysfs to control I/O request merge
functionality in the plug list. While this control has been
implemented for the request queue, it was dismissed in the plug list.
Therefore, block layer merges requests together (or attempt to merge)
even if the merge capability was disable using sysfs nomerge parameter
value 2.

This limitation is directly affects functionality of io_submit()
system call. The system call enables user to submit a bunch of IO
requests from user space using struct iocb **ios input argument.
However, the unconditioned merging functionality in the plug list
potentially merges these requests together down the road. Therefore,
there is no way to distinguish between an application sending bunch of
sequential IOs and an application sending one big IO. Ultimately, all
requests generated by the former app merge within the plug list
together and looks similar to the second app.

While the merging functionality is a desirable feature to improve the
performance of IO subsystem for some applications, it is not useful
for other application like ours at all.

Signed-off-by: Alireza Haghdoost <alireza@cs.umn.edu>
Reviewed-by: Jeff Moyer <jmoyer@redhat.com>
Coding style modified.

Signed-off-by: Jens Axboe <axboe@kernel.dk>

block: properly stack underlying max_segment_size to DM device

Without this patch all DM devices will default to BLK_MAX_SEGMENT_SIZE
(65536) even if the underlying device(s) have a larger value -- this is
due to blk_stack_limits() using min_not_zero() when stacking the
max_segment_size limit.

1073741824

before patch:
65536

after patch:
1073741824

Reported-by: Lukasz Flis <l.flis@cyfronet.pl>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Cc: stable@vger.kernel.org # v3.3+
Signed-off-by: Jens Axboe <axboe@kernel.dk>

elevator: acquire q->sysfs_lock in elevator_change()

Add locking of q->sysfs_lock into elevator_change() (an exported function)
to ensure it is held to protect q->elevator from elevator_init(), even if
elevator_change() is called from non-sysfs paths.
sysfs path (elv_iosched_store) uses __elevator_change(), non-locking
version, as the lock is already taken by elv_iosched_store().

Signed-off-by: Tomoki Sekiyama <tomoki.sekiyama@hds.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>

elevator: Fix a race in elevator switching and md device initialization

The soft lockup below happens at the boot time of the system using dm
multipath and the udev rules to switch scheduler.

[  356.127001] BUG: soft lockup - CPU#3 stuck for 22s! [sh:483]
[  356.127001] RIP: 0010:[<ffffffff81072a7d>]  [<ffffffff81072a7d>] lock_timer_base.isra.35+0x1d/0x50
...
[  356.127001] Call Trace:
[  356.127001]  [<ffffffff81073810>] try_to_del_timer_sync+0x20/0x70
[  356.127001]  [<ffffffff8118b08a>] ? kmem_cache_alloc_node_trace+0x20a/0x230
[  356.127001]  [<ffffffff810738b2>] del_timer_sync+0x52/0x60
[  356.127001]  [<ffffffff812ece22>] cfq_exit_queue+0x32/0xf0
[  356.127001]  [<ffffffff812c98df>] elevator_exit+0x2f/0x50
[  356.127001]  [<ffffffff812c9f21>] elevator_change+0xf1/0x1c0
[  356.127001]  [<ffffffff812caa50>] elv_iosched_store+0x20/0x50
[  356.127001]  [<ffffffff812d1d09>] queue_attr_store+0x59/0xb0
[  356.127001]  [<ffffffff812143f6>] sysfs_write_file+0xc6/0x140
[  356.127001]  [<ffffffff811a326d>] vfs_write+0xbd/0x1e0
[  356.127001]  [<ffffffff811a3ca9>] SyS_write+0x49/0xa0
[  356.127001]  [<ffffffff8164e899>] system_call_fastpath+0x16/0x1b

This is caused by a race between md device initialization by multipathd and
shell script to switch the scheduler using sysfs.

- multipathd:
   SyS_ioctl -> do_vfs_ioctl -> dm_ctl_ioctl -> ctl_ioctl -> table_load
   -> dm_setup_md_queue -> blk_init_allocated_queue -> elevator_init
    q->elevator = elevator_alloc(q, e); // not yet initialized

- sh -c 'echo deadline > /sys/$DEVPATH/queue/scheduler':
   elevator_switch (in the call trace above)
    struct elevator_queue *old = q->elevator;
    q->elevator = elevator_alloc(q, new_e);
    elevator_exit(old);                 // lockup! (*)

- multipathd: (cont.)
    err = e->ops.elevator_init_fn(q);   // init fails; q->elevator is modified

(*) When del_timer_sync() is called, lock_timer_base() will loop infinitely
while timer->base == NULL. In this case, as timer will never initialized,
it results in lockup.

This patch introduces acquisition of q->sysfs_lock around elevator_init()
into blk_init_allocated_queue(), to provide mutual exclusion between
initialization of the q->scheduler and switching of the scheduler.

This should fix this bugzilla:
https://bugzilla.redhat.com/show_bug.cgi?id=902012

Signed-off-by: Tomoki Sekiyama <tomoki.sekiyama@hds.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>

block: Replace __get_cpu_var uses

__get_cpu_var() is used for multiple purposes in the kernel source. One of
them is address calculation via the form &__get_cpu_var(x).  This calculates
the address for the instance of the percpu variable of the current processor
based on an offset.

Other use cases are for storing and retrieving data from the current
processors percpu area.  __get_cpu_var() can be used as an lvalue when
writing data or on the right side of an assignment.

__get_cpu_var() is defined as :

#define __get_cpu_var(var) (*this_cpu_ptr(&(var)))

__get_cpu_var() always only does an address determination. However, store
and retrieve operations could use a segment prefix (or global register on
other platforms) to avoid the address calculation.

this_cpu_write() and this_cpu_read() can directly take an offset into a
percpu area and use optimized assembly code to read and write per cpu
variables.

This patch converts __get_cpu_var into either an explicit address
calculation using this_cpu_ptr() or into a use of this_cpu operations that
use the offset.  Thereby address calculations are avoided and less registers
are used when code is generated.

At the end of the patch set all uses of __get_cpu_var have been removed so
the macro is removed too.

The patch set includes passes over all arches as well. Once these operations
are used throughout then specialized macros can be defined in non -x86
arches as well in order to optimize per cpu access by f.e.  using a global
register that may be set to the per cpu base.

Transformations done to __get_cpu_var()

1. Determine the address of the percpu instance of the current processor.

DEFINE_PER_CPU(int, y);
int *x = &__get_cpu_var(y);

    Converts to

int *x = this_cpu_ptr(&y);

2. Same as #1 but this time an array structure is involved.

DEFINE_PER_CPU(int, y[20]);
int *x = __get_cpu_var(y);

    Converts to

int *x = this_cpu_ptr(y);

3. Retrieve the content of the current processors instance of a per cpu
variable.

DEFINE_PER_CPU(int, y);
int x = __get_cpu_var(y)

   Converts to

int x = __this_cpu_read(y);

4. Retrieve the content of a percpu struct

DEFINE_PER_CPU(struct mystruct, y);
struct mystruct x = __get_cpu_var(y);

   Converts to

memcpy(&x, this_cpu_ptr(&y), sizeof(x));

5. Assignment to a per cpu variable

DEFINE_PER_CPU(int, y)
__get_cpu_var(y) = x;

   Converts to

this_cpu_write(y, x);

6. Increment/Decrement etc of a per cpu variable

DEFINE_PER_CPU(int, y);
__get_cpu_var(y)++

   Converts to

this_cpu_inc(y)

Signed-off-by: Christoph Lameter <cl@linux.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>

bdi: test bdi_init failure

There were two places where return value from bdi_init was not tested.

Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>

block: fix a probe argument to blk_register_region

The probe function is supposed to return NULL on failure (as we can see in
kobj_lookup: kobj = probe(dev, index, data); ... if (kobj) return kobj;

However, in loop and brd, it returns negative error from ERR_PTR.

This causes a crash if we simulate disk allocation failure and run
less -f /dev/loop0 because the negative number is interpreted as a pointer:

BUG: unable to handle kernel NULL pointer dereference at 00000000000002b4
IP: [<ffffffff8118b188>] __blkdev_get+0x28/0x450
PGD 23c677067 PUD 23d6d1067 PMD 0
Oops: 0000 [#1] PREEMPT SMP
Modules linked in: loop hpfs nvidia(PO) ip6table_filter ip6_tables uvesafb cfbcopyarea cfbimgblt cfbfillrect fbcon font bitblit fbcon_rotate fbcon_cw fbcon_ud fbcon_ccw softcursor fb fbdev msr ipt_MASQUERADE iptable_nat nf_nat_ipv4 nf_conntrack_ipv4 nf_defrag_ipv4 xt_state ipt_REJECT xt_tcpudp iptable_filter ip_tables x_tables bridge stp llc tun ipv6 cpufreq_stats cpufreq_ondemand cpufreq_userspace cpufreq_powersave cpufreq_conservative hid_generic spadfs usbhid hid fuse raid0 snd_usb_audio snd_pcm_oss snd_mixer_oss md_mod snd_pcm snd_timer snd_page_alloc snd_hwdep snd_usbmidi_lib dmi_sysfs snd_rawmidi nf_nat_ftp nf_nat nf_conntrack_ftp nf_conntrack snd soundcore lm85 hwmon_vid ohci_hcd ehci_pci ehci_hcd serverworks sata_svw libata acpi_cpufreq freq_table mperf ide_core usbcore kvm_amd kvm tg3 i2c_piix4 libphy microcode e100 usb_common ptp skge i2c_core pcspkr k10temp evdev floppy hwmon pps_core mii rtc_cmos button processor unix [last unloaded: nvidia]
CPU: 1 PID: 6831 Comm: less Tainted: P        W  O 3.10.15-devel #18
Hardware name: empty empty/S3992-E, BIOS 'V1.06   ' 06/09/2009
task: ffff880203cc6bc0 ti: ffff88023e47c000 task.ti: ffff88023e47c000
RIP: 0010:[<ffffffff8118b188>]  [<ffffffff8118b188>] __blkdev_get+0x28/0x450
RSP: 0018:ffff88023e47dbd8  EFLAGS: 00010286
RAX: ffffffffffffff74 RBX: ffffffffffffff74 RCX: 0000000000000000
RDX: 0000000000000000 RSI: 0000000000000000 RDI: 0000000000000001
RBP: ffff88023e47dc18 R08: 0000000000000002 R09: 0000000000000000
R10: 0000000000000000 R11: 0000000000000000 R12: ffff88023f519658
R13: ffffffff8118c300 R14: 0000000000000000 R15: ffff88023f519640
FS:  00007f2070bf7700(0000) GS:ffff880247400000(0000) knlGS:0000000000000000
CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00000000000002b4 CR3: 000000023da1d000 CR4: 00000000000007e0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000ffff0ff0 DR7: 0000000000000400
Stack:
0000000000000002 0000001d00000000 000000003e47dc50 ffff88023f519640
ffff88043d5bb668 ffffffff8118c300 ffff88023d683550 ffff88023e47de60
ffff88023e47dc98 ffffffff8118c10d 0000001d81605698 0000000000000292
Call Trace:
[<ffffffff8118c300>] ? blkdev_get_by_dev+0x60/0x60
[<ffffffff8118c10d>] blkdev_get+0x1dd/0x370
[<ffffffff8118c300>] ? blkdev_get_by_dev+0x60/0x60
[<ffffffff813cea6c>] ? _raw_spin_unlock+0x2c/0x50
[<ffffffff8118c300>] ? blkdev_get_by_dev+0x60/0x60
[<ffffffff8118c365>] blkdev_open+0x65/0x80
[<ffffffff8114d12e>] do_dentry_open.isra.18+0x23e/0x2f0
[<ffffffff8114d214>] finish_open+0x34/0x50
[<ffffffff8115e122>] do_last.isra.62+0x2d2/0xc50
[<ffffffff8115eb58>] path_openat.isra.63+0xb8/0x4d0
[<ffffffff81115a8e>] ? might_fault+0x4e/0xa0
[<ffffffff8115f4f0>] do_filp_open+0x40/0x90
[<ffffffff813cea6c>] ? _raw_spin_unlock+0x2c/0x50
[<ffffffff8116db85>] ? __alloc_fd+0xa5/0x1f0
[<ffffffff8114e45f>] do_sys_open+0xef/0x1d0
[<ffffffff8114e559>] SyS_open+0x19/0x20
[<ffffffff813cff16>] system_call_fastpath+0x1a/0x1f
Code: 44 00 00 55 48 89 e5 41 57 49 89 ff 41 56 41 89 d6 41 55 41 54 4c 8d 67 18 53 48 83 ec 18 89 75 cc e9 f2 00 00 00 0f 1f 44 00 00 <48> 8b 80 40 03 00 00 48 89 df 4c 8b 68 58 e8 d5
a4 07 00 44 89
RIP  [<ffffffff8118b188>] __blkdev_get+0x28/0x450
RSP <ffff88023e47dbd8>
CR2: 00000000000002b4
---[ end trace bb7f32dbf02398dc ]---

The brd change should be backported to stable kernels starting with 2.6.25.
The loop change should be backported to stable kernels starting with 2.6.22.

Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Acked-by: Tejun Heo <tj@kernel.org>
Cc: stable@kernel.org # 2.6.22+
Signed-off-by: Jens Axboe <axboe@kernel.dk>

loop: fix crash if blk_alloc_queue fails

loop: fix crash if blk_alloc_queue fails

If blk_alloc_queue fails, loop_add cleans up, but it doesn't clean up the
identifier allocated with idr_alloc. That causes crash on module unload in
idr_for_each(&loop_index_idr, &loop_exit_cb, NULL); where we attempt to
remove non-existed device with that id.

BUG: unable to handle kernel NULL pointer dereference at 0000000000000380
IP: [<ffffffff812057c9>] del_gendisk+0x19/0x2d0
PGD 43d399067 PUD 43d0ad067 PMD 0
Oops: 0000 [#1] PREEMPT SMP
Modules linked in: loop(-) dm_snapshot dm_zero dm_mirror dm_region_hash dm_log dm_loop dm_mod ip6table_filter ip6_tables uvesafb cfbcopyarea cfbimgblt cfbfillrect fbcon font bitblit fbcon_rotate fbcon_cw fbcon_ud fbcon_ccw softcursor fb fbdev msr ipt_MASQUERADE iptable_nat nf_nat_ipv4 nf_conntrack_ipv4 nf_defrag_ipv4 xt_state ipt_REJECT xt_tcpudp iptable_filter ip_tables x_tables bridge stp llc tun ipv6 cpufreq_userspace cpufreq_stats cpufreq_ondemand cpufreq_conservative cpufreq_powersave spadfs fuse hid_generic usbhid hid raid0 md_mod dmi_sysfs nf_nat_ftp nf_nat nf_conntrack_ftp nf_conntrack snd_usb_audio snd_pcm_oss snd_mixer_oss snd_pcm snd_timer snd_page_alloc lm85 hwmon_vid snd_hwdep snd_usbmidi_lib snd_rawmidi snd soundcore acpi_cpufreq ohci_hcd freq_table tg3 ehci_pci mperf ehci_hcd kvm_amd kvm sata_svw serverworks libphy libata ide_core k10temp usbcore hwmon microcode ptp pcspkr pps_core e100 skge mii usb_common i2c_piix4 floppy evdev rtc_cmos i2c_core processor but!
ton unix
CPU: 7 PID: 2735 Comm: rmmod Tainted: G        W    3.10.15-devel #15
Hardware name: empty empty/S3992-E, BIOS 'V1.06   ' 06/09/2009
task: ffff88043d38e780 ti: ffff88043d21e000 task.ti: ffff88043d21e000
RIP: 0010:[<ffffffff812057c9>]  [<ffffffff812057c9>] del_gendisk+0x19/0x2d0
RSP: 0018:ffff88043d21fe10  EFLAGS: 00010282
RAX: ffffffffa05102e0 RBX: 0000000000000000 RCX: 0000000000000000
RDX: 0000000000000000 RSI: ffff88043ea82800 RDI: 0000000000000000
RBP: ffff88043d21fe48 R08: 0000000000000000 R09: 0000000000000001
R10: 0000000000000001 R11: 0000000000000000 R12: 00000000000000ff
R13: 0000000000000080 R14: 0000000000000000 R15: ffff88043ea82800
FS:  00007ff646534700(0000) GS:ffff880447000000(0000) knlGS:0000000000000000
CS:  0010 DS: 0000 ES: 0000 CR0: 000000008005003b
CR2: 0000000000000380 CR3: 000000043e9bf000 CR4: 00000000000007e0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000ffff0ff0 DR7: 0000000000000400
Stack:
ffffffff8100aba4 0000000000000092 ffff88043d21fe48 ffff88043ea82800
00000000000000ff ffff88043d21fe98 0000000000000000 ffff88043d21fe60
ffffffffa05102b4 0000000000000000 ffff88043d21fe70 ffffffffa05102ec
Call Trace:
[<ffffffff8100aba4>] ? native_sched_clock+0x24/0x80
[<ffffffffa05102b4>] loop_remove+0x14/0x40 [loop]
[<ffffffffa05102ec>] loop_exit_cb+0xc/0x10 [loop]
[<ffffffff81217b74>] idr_for_each+0x104/0x190
[<ffffffffa05102e0>] ? loop_remove+0x40/0x40 [loop]
[<ffffffff8109adc5>] ? trace_hardirqs_on_caller+0x105/0x1d0
[<ffffffffa05135dc>] loop_exit+0x34/0xa58 [loop]
[<ffffffff810a98ea>] SyS_delete_module+0x13a/0x260
[<ffffffff81221d5e>] ? trace_hardirqs_on_thunk+0x3a/0x3f
[<ffffffff813cff16>] system_call_fastpath+0x1a/0x1f
Code: f0 4c 8b 6d f8 c9 c3 66 66 2e 0f 1f 84 00 00 00 00 00 55 48 89 e5 41 56 41 55 4c 8d af 80 00 00 00 41 54 53 48 89 fb 48 83 ec 18 <48> 83 bf 80 03 00
00 00 74 4d e8 98 fe ff ff 31 f6 48 c7 c7 20
RIP  [<ffffffff812057c9>] del_gendisk+0x19/0x2d0
RSP <ffff88043d21fe10>
CR2: 0000000000000380
---[ end trace 64ec069ec70f1309 ]---

Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Acked-by: Tejun Heo <tj@kernel.org>
Cc: stable@kernel.org # 3.1+
Signed-off-by: Jens Axboe <axboe@kernel.dk>

blk-core: Fix memory corruption if blkcg_init_queue fails

If blkcg_init_queue fails, blk_alloc_queue_node doesn't call bdi_destroy
to clean up structures allocated by the backing dev.

------------[ cut here ]------------
WARNING: at lib/debugobjects.c:260 debug_print_object+0x85/0xa0()
ODEBUG: free active (active state 0) object type: percpu_counter hint:           (null)
Modules linked in: dm_loop dm_mod ip6table_filter ip6_tables uvesafb cfbcopyarea cfbimgblt cfbfillrect fbcon font bitblit fbcon_rotate fbcon_cw fbcon_ud fbcon_ccw softcursor fb fbdev ipt_MASQUERADE iptable_nat nf_nat_ipv4 msr nf_conntrack_ipv4 nf_defrag_ipv4 xt_state ipt_REJECT xt_tcpudp iptable_filter ip_tables x_tables bridge stp llc tun ipv6 cpufreq_userspace cpufreq_stats cpufreq_powersave cpufreq_ondemand cpufreq_conservative spadfs fuse hid_generic usbhid hid raid0 md_mod dmi_sysfs nf_nat_ftp nf_nat nf_conntrack_ftp nf_conntrack lm85 hwmon_vid snd_usb_audio snd_pcm_oss snd_mixer_oss snd_pcm snd_timer snd_page_alloc snd_hwdep snd_usbmidi_lib snd_rawmidi snd soundcore acpi_cpufreq freq_table mperf sata_svw serverworks kvm_amd ide_core ehci_pci ohci_hcd libata ehci_hcd kvm usbcore tg3 usb_common libphy k10temp pcspkr ptp i2c_piix4 i2c_core evdev microcode hwmon rtc_cmos pps_core e100 skge floppy mii processor button unix
CPU: 0 PID: 2739 Comm: lvchange Tainted: G        W
3.10.15-devel #14
Hardware name: empty empty/S3992-E, BIOS 'V1.06   ' 06/09/2009
0000000000000009 ffff88023c3c1ae8 ffffffff813c8fd4 ffff88023c3c1b20
ffffffff810399eb ffff88043d35cd58 ffffffff81651940 ffff88023c3c1bf8
ffffffff82479d90 0000000000000005 ffff88023c3c1b80 ffffffff81039a67
Call Trace:
[<ffffffff813c8fd4>] dump_stack+0x19/0x1b
[<ffffffff810399eb>] warn_slowpath_common+0x6b/0xa0
[<ffffffff81039a67>] warn_slowpath_fmt+0x47/0x50
[<ffffffff8122aaaf>] ? debug_check_no_obj_freed+0xcf/0x250
[<ffffffff81229a15>] debug_print_object+0x85/0xa0
[<ffffffff8122abe3>] debug_check_no_obj_freed+0x203/0x250
[<ffffffff8113c4ac>] kmem_cache_free+0x20c/0x3a0
[<ffffffff811f6709>] blk_alloc_queue_node+0x2a9/0x2c0
[<ffffffff811f672e>] blk_alloc_queue+0xe/0x10
[<ffffffffa04c0093>] dm_create+0x1a3/0x530 [dm_mod]
[<ffffffffa04c6bb0>] ? list_version_get_info+0xe0/0xe0 [dm_mod]
[<ffffffffa04c6c07>] dev_create+0x57/0x2b0 [dm_mod]
[<ffffffffa04c6bb0>] ? list_version_get_info+0xe0/0xe0 [dm_mod]
[<ffffffffa04c6bb0>] ? list_version_get_info+0xe0/0xe0 [dm_mod]
[<ffffffffa04c6528>] ctl_ioctl+0x268/0x500 [dm_mod]
[<ffffffff81097662>] ? get_lock_stats+0x22/0x70
[<ffffffffa04c67ce>] dm_ctl_ioctl+0xe/0x20 [dm_mod]
[<ffffffff81161aad>] do_vfs_ioctl+0x2ed/0x520
[<ffffffff8116cfc7>] ? fget_light+0x377/0x4e0
[<ffffffff81161d2b>] SyS_ioctl+0x4b/0x90
[<ffffffff813cff16>] system_call_fastpath+0x1a/0x1f
---[ end trace 4b5ff0d55673d986 ]---
------------[ cut here ]------------

This fix should be backported to stable kernels starting with 2.6.37. Note
that in the kernels prior to 3.5 the affected code is different, but the
bug is still there - bdi_init is called and bdi_destroy isn't.

Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Acked-by: Tejun Heo <tj@kernel.org>
Cc: stable@kernel.org # 2.6.37+
Signed-off-by: Jens Axboe <axboe@kernel.dk>

block: fix race between request completion and timeout handling

crocode i2c_i801 i2c_core iTCO_wdt iTCO_vendor_support shpchp ioatdma dca be2net sg ses enclosure ext4 mbcache jbd2 sd_mod crc_t10dif ahci megaraid_sas(U) dm_mirror dm_region_hash dm_log dm_mod [last unloaded: scsi_wait_scan]

Pid: 491, comm: scsi_eh_0 Tainted: G        W  ----------------   2.6.32-220.13.1.el6.x86_64 #1 IBM  -[8722PAX]-/00D1461
RIP: 0010:[<ffffffff8124e424>]  [<ffffffff8124e424>] blk_requeue_request+0x94/0xa0
RSP: 0018:ffff881057eefd60  EFLAGS: 00010012
RAX: ffff881d99e3e8a8 RBX: ffff881d99e3e780 RCX: ffff881d99e3e8a8
RDX: ffff881d99e3e8a8 RSI: ffff881d99e3e780 RDI: ffff881d99e3e780
RBP: ffff881057eefd80 R08: ffff881057eefe90 R09: 0000000000000000
R10: 0000000000000000 R11: 0000000000000000 R12: ffff881057f92338
R13: 0000000000000000 R14: ffff881057f92338 R15: ffff883058188000
FS:  0000000000000000(0000) GS:ffff880040200000(0000) knlGS:0000000000000000
CS:  0010 DS: 0018 ES: 0018 CR0: 000000008005003b
CR2: 00000000006d3ec0 CR3: 000000302cd7d000 CR4: 00000000000406b0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000ffff0ff0 DR7: 0000000000000400
Process scsi_eh_0 (pid: 491, threadinfo ffff881057eee000, task ffff881057e29540)
Stack:
0000000000001057 0000000000000286 ffff8810275efdc0 ffff881057f16000
<0> ffff881057eefdd0 ffffffff81362323 ffff881057eefe20 ffffffff8135f393
<0> ffff881057e29af8 ffff8810275efdc0 ffff881057eefe78 ffff881057eefe90
Call Trace:
[<ffffffff81362323>] __scsi_queue_insert+0xa3/0x150
[<ffffffff8135f393>] ? scsi_eh_ready_devs+0x5e3/0x850
[<ffffffff81362a23>] scsi_queue_insert+0x13/0x20
[<ffffffff8135e4d4>] scsi_eh_flush_done_q+0x104/0x160
[<ffffffff8135fb6b>] scsi_error_handler+0x35b/0x660
[<ffffffff8135f810>] ? scsi_error_handler+0x0/0x660
[<ffffffff810908c6>] kthread+0x96/0xa0
[<ffffffff8100c14a>] child_rip+0xa/0x20
[<ffffffff81090830>] ? kthread+0x0/0xa0
[<ffffffff8100c140>] ? child_rip+0x0/0x20
Code: 00 00 eb d1 4c 8b 2d 3c 8f 97 00 4d 85 ed 74 bf 49 8b 45 00 49 83 c5 08 48 89 de 4c 89 e7 ff d0 49 8b 45 00 48 85 c0 75 eb eb a4 <0f> 0b eb fe 0f 1f 84 00 00 00 00 00 55 48 89 e5 0f 1f 44 00 00
RIP  [<ffffffff8124e424>] blk_requeue_request+0x94/0xa0
RSP <ffff881057eefd60>

The RIP is this line:
        BUG_ON(blk_queued_rq(rq));

After digging through the code, I think there may be a race between the
request completion and the timer handler running.

A timer is started for each request put on the device's queue (see
blk_start_request->blk_add_timer).  If the request does not complete
before the timer expires, the timer handler (blk_rq_timed_out_timer)
will mark the request complete atomically:

static inline int blk_mark_rq_complete(struct request *rq)
{
        return test_and_set_bit(REQ_ATOM_COMPLETE, &rq->atomic_flags);
}

and then call blk_rq_timed_out.  The latter function will call
scsi_times_out, which will return one of BLK_EH_HANDLED,
BLK_EH_RESET_TIMER or BLK_EH_NOT_HANDLED.  If BLK_EH_RESET_TIMER is
returned, blk_clear_rq_complete is called, and blk_add_timer is again
called to simply wait longer for the request to complete.

Now, if the request happens to complete while this is going on, what
happens?  Given that we know the completion handler will bail if it
finds the REQ_ATOM_COMPLETE bit set, we need to focus on the completion
handler running after that bit is cleared.  So, from the above
paragraph, after the call to blk_clear_rq_complete.  If the completion
sets REQ_ATOM_COMPLETE before the BUG_ON in blk_add_timer, we go boom
there (I haven't seen this in the cores).  Next, if we get the
completion before the call to list_add_tail, then the timer will
eventually fire for an old req, which may either be freed or reallocated
(there is evidence that this might be the case).  Finally, if the
completion comes in *after* the addition to the timeout list, I think
it's harmless.  The request will be removed from the timeout list,
req_atom_complete will be set, and all will be well.

This will only actually explain the coredumps *IF* the request
structure was freed, reallocated *and* queued before the error handler
thread had a chance to process it.  That is possible, but it may make
sense to keep digging for another race.  I think that if this is what
was happening, we would see other instances of this problem showing up
as null pointer or garbage pointer dereferences, for example when the
request structure was not re-used.  It looks like we actually do run
into that situation in other reports.

This patch moves the BUG_ON(test_bit(REQ_ATOM_COMPLETE,
&req->atomic_flags)); from blk_add_timer to the only caller that could
trip over it (blk_start_request).  It then inverts the calls to
blk_clear_rq_complete and blk_add_timer in blk_rq_timed_out to address
the race.  I've boot tested this patch, but nothing more.

Signed-off-by: Jeff Moyer <jmoyer@redhat.com>
Acked-by: Hannes Reinecke <hare@suse.de>
Cc: stable@kernel.org
Signed-off-by: Jens Axboe <axboe@kernel.dk>

blktrace: Send BLK_TN_PROCESS events to all running traces

Currently each task sends BLK_TN_PROCESS event to the first traced
device it interacts with after a new trace is started. When there are
several traced devices and the task accesses more devices, this logic
can result in BLK_TN_PROCESS being sent several times to some devices
while it is never sent to other devices. Thus blkparse doesn't display
command name when parsing some blktrace files.

Fix the problem by sending BLK_TN_PROCESS event to all traced devices
when a task interacts with any of them.

Signed-off-by: Jan Kara <jack@suse.cz>
Review-by: Jeff Moyer <jmoyer@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>

Linux 3.12

Merge branch 'upstream' of git://git.linux-mips.org/ralf/upstream-linus

Pull MIPS fixes from Ralf Baechle:
"Three fixes across arch/mips with the most complex one being the GIC
  interrupt fix - at nine lines still not monster.  I'm confident this
  are the final MIPS patches even if there should go for an rc8"

* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus:
  MIPS: ralink: fix return value check in rt_timer_probe()
  MIPS: malta: Fix GIC interrupt offsets
  MIPS: Perf: Fix 74K cache map

ipc, msg: forbid negative values for "msg{max,mnb,mni}"

Negative message lengths make no sense -- so don't do negative queue
lenghts or identifier counts. Prevent them from getting negative.

Also change the underlying data types to be unsigned to avoid hairy
surprises with sign extensions in cases where those variables get
evaluated in unsigned expressions with bigger data types, e.g size_t.

In case a user still wants to have "unlimited" sizes she could just use
INT_MAX instead.

Signed-off-by: Mathias Krause <minipli@googlemail.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Merge tag 'fixes-for-linus' of git://git./linux/kernel/git/rusty/linux

Pull ARM kallsyms fix from Rusty Russell:
"Last minute perf unbreakage for ARM modules; spent a day in
linux-next"

* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux:
scripts/kallsyms: filter symbols not in kernel address space

ARC: Incorrect mm reference used in vmalloc fault handler

A vmalloc fault needs to sync up PGD/PTE entry from init_mm to current
task's "active_mm".  ARC vmalloc fault handler however was using mm.

A vmalloc fault for non user task context (actually pre-userland, from
init thread's open for /dev/console) caused the handler to deref NULL mm
(for mm->pgd)

The reasons it worked so far is amazing:

1. By default (!SMP), vmalloc fault handler uses a cached value of PGD.
   In SMP that MMU register is repurposed hence need for mm pointer deref.

2. In pre-3.12 SMP kernel, the problem triggering vmalloc didn't exist in
   pre-userland code path - it was introduced with commit 20bafb3d23d108bc
   "n_tty: Move buffers into n_tty_data"

Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Cc: Gilad Ben-Yossef <gilad@benyossef.com>
Cc: Noam Camus <noamc@ezchip.com>
Cc: stable@vger.kernel.org #3.10 and 3.11
Cc: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

scripts/kallsyms: filter symbols not in kernel address space

This patch uses CONFIG_PAGE_OFFSET to filter symbols which
are not in kernel address space because these symbols are
generally for generating code purpose and can't be run at
kernel mode, so we needn't keep them in /proc/kallsyms.

For example, on ARM there are some symbols which may be
linked in relocatable code section, then perf can't parse
symbols any more from /proc/kallsyms, this patch fixes the
problem (introduced b9b32bf70f2fb710b07c94e13afbc729afe221da)

Cc: Russell King <linux@arm.linux.org.uk>
Cc: linux-arm-kernel@lists.infradead.org
Cc: Michal Marek <mmarek@suse.cz>
Signed-off-by: Ming Lei <tom.leiming@gmail.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Cc: stable@vger.kernel.org

Merge branch 'perf-urgent-for-linus' of git://git./linux/kernel/git/tip/tip

Pull perf fixes from Ingo Molnar:
"Two fixes:

   - Fix 'NMI handler took too long to run' false positives

     [ Genuine NMI overhead speedups will come for v3.13, this commit
       only fixes a measurement bug ]

   - Fix perf ring-buffer missed barrier causing (rare) ring-buffer data
     corruption on ppc64"

* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  perf/x86: Fix NMI measurements
  perf: Fix perf ring buffer memory ordering

Merge tag 'usb-3.12-rc8' of git://git./linux/kernel/git/gregkh/usb

Pull USB fixes from Greg KH:
"Here is a set of patches that revert all of the changes done to the
  pl2303 USB serial driver in the 3.12-rc timeframe, as it turns out
  they break some devices that work just fine on 3.11.  As it's not a
  good idea to break working systems, drop them all and they will be
  reworked for future kernel versions such that there is no breakage.

  I've also included a MAINTAINERS update for the USB serial subsystem
  and a new device id for the ftdi_sio driver as well"

* tag 'usb-3.12-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
  USB: serial: ftdi_sio: add id for Z3X Box device
  USB: Maintainers change for usb serial drivers
  Revert "USB: pl2303: restrict the divisor based baud rate encoding method to the "HX" chip type"
  Revert "usb: pl2303: fix+improve the divsor based baud rate encoding method"
  Revert "usb: pl2303: do not round to the next nearest standard baud rate for the divisor based baud rate encoding method"
  Revert "usb: pl2303: remove 500000 baud from the list of standard baud rates"
  Revert "usb: pl2303: move the two baud rate encoding methods to separate functions"
  Revert "usb: pl2303: increase the allowed baud rate range for the divisor based encoding method"
  Revert "usb: pl2303: also use the divisor based baud rate encoding method for baud rates < 115200 with HX chips"
  Revert "usb: pl2303: add two comments concerning the supported baud rates with HX chips"
  Revert "pl2303: simplify the else-if contruct for type_1 chips in pl2303_startup()"
  Revert "pl2303: improve the chip type information output on startup"
  Revert "pl2303: improve the chip type detection/distinction"
  Revert "USB: pl2303: distinguish between original and cloned HX chips"

Merge tag 'sound-3.12' of git://git./linux/kernel/git/tiwai/sound

Pull more sound fixes from Takashi Iwai:
"The fixes for random bugs that have been reported lately in the game:
  a few fixes in ASoC dpam and wm_hubs bugs spotted by Coverity, a
  one-liner HD-audio fixup, and a fix for Oops with DPCM.

  They are not so critically urgent bugs, but all small and safe"

* tag 'sound-3.12' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
  ALSA: fix oops in snd_pcm_info() caused by ASoC DPCM
  ASoC: wm_hubs: Add missing break in hp_supply_event()
  ALSA: hda - Add a fixup for ASUS N76VZ
  ASoC: dapm: Return -ENOMEM in snd_soc_dapm_new_dai_widgets()
  ASoC: dapm: Fix source list debugfs outputs

Merge tag 'clk-fixes-for-linus' of git://git.linaro.org/people/mturquette/linux

Pull clock subsystem fixes from Mike Turquette.

* tag 'clk-fixes-for-linus' of git://git.linaro.org/people/mturquette/linux:
  clk: fixup argument order when setting VCO parameters
  clk: socfpga: Fix incorrect sdmmc clock name
  clk: armada-370: fix tclk frequencies
  clk: nomadik: set all timers to use 2.4 MHz TIMCLK

memcg: remove incorrect underflow check

When a memcg is deleted mem_cgroup_reparent_charges() moves charged
memory to the parent memcg.  As of v3.11-9444-g3ea67d0 "memcg: add per
cgroup writeback pages accounting" there's bad pointer read.  The goal
was to check for counter underflow.  The counter is a per cpu counter
and there are two problems with the code:

(1) per cpu access function isn't used, instead a naked pointer is used
     which easily causes oops.
(2) the check doesn't sum all cpus

Test:
  $ cd /sys/fs/cgroup/memory
  $ mkdir x
  $ echo 3 > /proc/sys/vm/drop_caches
  $ (echo $BASHPID >> x/tasks && exec cat) &
  [1] 7154
  $ grep ^mapped x/memory.stat
  mapped_file 53248
  $ echo 7154 > tasks
  $ rmdir x
  <OOPS>

The fix is to remove the check.  It's currently dangerous and isn't
worth fixing it to use something expensive, such as
percpu_counter_sum(), for each reparented page.  __this_cpu_read() isn't
enough to fix this because there's no guarantees of the current cpus
count.  The only guarantees is that the sum of all per-cpu counter is >=
nr_pages.

Fixes: 3ea67d06e467 ("memcg: add per cgroup writeback pages accounting")
Reported-and-tested-by: Flavio Leitner <fbl@redhat.com>
Signed-off-by: Greg Thelen <gthelen@google.com>
Reviewed-by: Sha Zhengju <handai.szj@taobao.com>
Acked-by: Johannes Weiner <hannes@cmpxchg.org>
Signed-off-by: Hugh Dickins <hughd@google.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

USB: serial: ftdi_sio: add id for Z3X Box device

Custom VID/PID for Z3X Box device, popular tool for cellphone flashing.

Signed-off-by: Alexey E. Kramarenko <alexeyk13@yandex.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

USB: Maintainers change for usb serial drivers

Johan has been conned^Wgracious in accepting the maintainership of the
USB serial drivers, especially as he's been doing all of the real work
for the past few years.

At the same time, remove a bunch of old entries for USB serial drivers
that don't make sense anymore, given that the developers are no longer
around, and individual driver maintainerships for tiny things like this
is pretty pointless.

Acked-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Revert "USB: pl2303: restrict the divisor based baud rate encoding method to the "HX" chip type"

This reverts commit b8bdad608213caffa081a97d2e937e5fe08c4046.

Revert all of the pl2303 changes that went into 3.12-rc1 and -rc2 as
they cause regressions on some versions of the chip. This will all be
revisited for later kernel versions when we can figure out how to handle
this in a way that does not break working devices.

Reported-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Cc: Frank Schäfer <fschaefer.oss@googlemail.com>
Acked-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Revert "usb: pl2303: fix+improve the divsor based baud rate encoding method"

This reverts commit 57ce61aad748ceaa08c859da04043ad7dae7c15e.

Revert all of the pl2303 changes that went into 3.12-rc1 and -rc2 as
they cause regressions on some versions of the chip. This will all be
revisited for later kernel versions when we can figure out how to handle
this in a way that does not break working devices.

Reported-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Cc: Frank Schäfer <fschaefer.oss@googlemail.com>
Acked-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Revert "usb: pl2303: do not round to the next nearest standard baud rate for the divisor based baud rate encoding method"

This reverts commit 75417d9f99f89ab241de69d7db15af5842b488c4.

Revert all of the pl2303 changes that went into 3.12-rc1 and -rc2 as
they cause regressions on some versions of the chip. This will all be
revisited for later kernel versions when we can figure out how to handle
this in a way that does not break working devices.

Reported-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Cc: Frank Schäfer <fschaefer.oss@googlemail.com>
Acked-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Revert "usb: pl2303: remove 500000 baud from the list of standard baud rates"

This reverts commit b9208c721ce736125fe58d398319513a27850fd8.

Revert all of the pl2303 changes that went into 3.12-rc1 and -rc2 as
they cause regressions on some versions of the chip. This will all be
revisited for later kernel versions when we can figure out how to handle
this in a way that does not break working devices.

Reported-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Cc: Frank Schäfer <fschaefer.oss@googlemail.com>
Acked-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Revert "usb: pl2303: move the two baud rate encoding methods to separate functions"

This reverts commit e917ba01d69ad705a4cd6a6c77538f55d84f5907.

Revert all of the pl2303 changes that went into 3.12-rc1 and -rc2 as
they cause regressions on some versions of the chip. This will all be
revisited for later kernel versions when we can figure out how to handle
this in a way that does not break working devices.

Reported-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Cc: Frank Schäfer <fschaefer.oss@googlemail.com>
Acked-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Revert "usb: pl2303: increase the allowed baud rate range for the divisor based encoding method"

This reverts commit b5c16c6a031c52cc4b7dda6c3de46462fbc92eab.

Revert all of the pl2303 changes that went into 3.12-rc1 and -rc2 as
they cause regressions on some versions of the chip. This will all be
revisited for later kernel versions when we can figure out how to handle
this in a way that does not break working devices.

Reported-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Cc: Frank Schäfer <fschaefer.oss@googlemail.com>
Acked-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Revert "usb: pl2303: also use the divisor based baud rate encoding method for baud rates < 115200 with HX chips"

This reverts commit 61fa8d694b8547894b57ea0d99d0120a58f6ebf8.

Revert all of the pl2303 changes that went into 3.12-rc1 and -rc2 as
they cause regressions on some versions of the chip. This will all be
revisited for later kernel versions when we can figure out how to handle
this in a way that does not break working devices.

Reported-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Cc: Frank Schäfer <fschaefer.oss@googlemail.com>
Acked-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Revert "usb: pl2303: add two comments concerning the supported baud rates with HX chips"

This reverts commit c23bda365dfbf56aa4d6d4a97f83136c36050e01.

Revert all of the pl2303 changes that went into 3.12-rc1 and -rc2 as
they cause regressions on some versions of the chip. This will all be
revisited for later kernel versions when we can figure out how to handle
this in a way that does not break working devices.

Reported-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Cc: Frank Schäfer <fschaefer.oss@googlemail.com>
Acked-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Revert "pl2303: simplify the else-if contruct for type_1 chips in pl2303_startup()"

This reverts commit 73b583af597542329e6adae44524da6f27afed62.

Revert all of the pl2303 changes that went into 3.12-rc1 and -rc2 as
they cause regressions on some versions of the chip. This will all be
revisited for later kernel versions when we can figure out how to handle
this in a way that does not break working devices.

Reported-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Cc: Frank Schäfer <fschaefer.oss@googlemail.com>
Acked-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Revert "pl2303: improve the chip type information output on startup"

This reverts commit a77a8c23e4db9fb1f776147eda0d85117359c700.

Revert all of the pl2303 changes that went into 3.12-rc1 and -rc2 as
they cause regressions on some versions of the chip. This will all be
revisited for later kernel versions when we can figure out how to handle
this in a way that does not break working devices.

Reported-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Cc: Frank Schäfer <fschaefer.oss@googlemail.com>
Acked-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Revert "pl2303: improve the chip type detection/distinction"

This reverts commit 034d1527adebd302115c87ef343497a889638275.

Revert all of the pl2303 changes that went into 3.12-rc1 and -rc2 as
they cause regressions on some versions of the chip. This will all be
revisited for later kernel versions when we can figure out how to handle
this in a way that does not break working devices.

Reported-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Cc: Frank Schäfer <fschaefer.oss@googlemail.com>
Acked-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Revert "USB: pl2303: distinguish between original and cloned HX chips"

This reverts commit 7d26a78f62ff4fb08bc5ba740a8af4aa7ac67da4.

Revert all of the pl2303 changes that went into 3.12-rc1 and -rc2 as
they cause regressions on some versions of the chip. This will all be
revisited for later kernel versions when we can figure out how to handle
this in a way that does not break working devices.

Reported-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Cc: Frank Schäfer <fschaefer.oss@googlemail.com>
Acked-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Merge branch 'akpm' (fixes from Andrew Morton)

Merge four more fixes from Andrew Morton.

* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
  lib/scatterlist.c: don't flush_kernel_dcache_page on slab page
  mm: memcg: fix test for child groups
  mm: memcg: lockdep annotation for memcg OOM lock
  mm: memcg: use proper memcg in limit bypass

lib/scatterlist.c: don't flush_kernel_dcache_page on slab page

Commit b1adaf65ba03 ("[SCSI] block: add sg buffer copy helper
functions") introduces two sg buffer copy helpers, and calls
flush_kernel_dcache_page() on pages in SG list after these pages are
written to.

Unfortunately, the commit may introduce a potential bug:

- Before sending some SCSI commands, kmalloc() buffer may be passed to
   block layper, so flush_kernel_dcache_page() can see a slab page
   finally

- According to cachetlb.txt, flush_kernel_dcache_page() is only called
   on "a user page", which surely can't be a slab page.

- ARCH's implementation of flush_kernel_dcache_page() may use page
   mapping information to do optimization so page_mapping() will see the
   slab page, then VM_BUG_ON() is triggered.

Aaro Koskinen reported the bug on ARM/kirkwood when DEBUG_VM is enabled,
and this patch fixes the bug by adding test of '!PageSlab(miter->page)'
before calling flush_kernel_dcache_page().

Signed-off-by: Ming Lei <ming.lei@canonical.com>
Reported-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Tested-by: Simon Baatz <gmbnomis@gmail.com>
Cc: Russell King - ARM Linux <linux@arm.linux.org.uk>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Aaro Koskinen <aaro.koskinen@iki.fi>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Cc: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Cc: Tejun Heo <tj@kernel.org>
Cc: "James E.J. Bottomley" <JBottomley@parallels.com>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: <stable@vger.kernel.org> [3.2+]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

mm: memcg: fix test for child groups

When memcg code needs to know whether any given memcg has children, it
uses the cgroup child iteration primitives and returns true/false
depending on whether the iteration loop is executed at least once or
not.

Because a cgroup's list of children is RCU protected, these primitives
require the RCU read-lock to be held, which is not the case for all
memcg callers.  This results in the following splat when e.g.  enabling
hierarchy mode:

  WARNING: CPU: 3 PID: 1 at kernel/cgroup.c:3043 css_next_child+0xa3/0x160()
  CPU: 3 PID: 1 Comm: systemd Not tainted 3.12.0-rc5-00117-g83f11a9-dirty #18
  Hardware name: LENOVO 3680B56/3680B56, BIOS 6QET69WW (1.39 ) 04/26/2012
  Call Trace:
    dump_stack+0x54/0x74
    warn_slowpath_common+0x78/0xa0
    warn_slowpath_null+0x1a/0x20
    css_next_child+0xa3/0x160
    mem_cgroup_hierarchy_write+0x5b/0xa0
    cgroup_file_write+0x108/0x2a0
    vfs_write+0xbd/0x1e0
    SyS_write+0x4c/0xa0
    system_call_fastpath+0x16/0x1b

In the memcg case, we only care about children when we are attempting to
modify inheritable attributes interactively.  Racing with deletion could
mean a spurious -EBUSY, no problem.  Racing with addition is handled
just fine as well through the memcg_create_mutex: if the child group is
not on the list after the mutex is acquired, it won't be initialized
from the parent's attributes until after the unlock.

Signed-off-by: Johannes Weiner <hannes@cmpxchg.org>
Acked-by: Michal Hocko <mhocko@suse.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

mm: memcg: lockdep annotation for memcg OOM lock

The memcg OOM lock is a mutex-type lock that is open-coded due to
memcg's special needs. Add annotations for lockdep coverage.

Signed-off-by: Johannes Weiner <hannes@cmpxchg.org>
Cc: Michal Hocko <mhocko@suse.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

mm: memcg: use proper memcg in limit bypass

Commit 84235de394d9 ("fs: buffer: move allocation failure loop into the
allocator") allowed __GFP_NOFAIL allocations to bypass the limit if they
fail to reclaim enough memory for the charge.  But because the main test
case was on a 3.2-based system, the patch missed the fact that on newer
kernels the charge function needs to return root_mem_cgroup when
bypassing the limit, and not NULL.  This will corrupt whatever memory is
at NULL + percpu pointer offset.  Fix this quickly before problems are
reported.

Signed-off-by: Johannes Weiner <hannes@cmpxchg.org>
Acked-by: Michal Hocko <mhocko@suse.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

vfs: decrapify dput(), fix cache behavior under normal load

We do not want to dirty the dentry->d_flags cacheline in dput() just to
set the DCACHE_REFERENCED flag when it is already set in the common case
anyway. This way the first cacheline of the dentry (which contains the
RCU lookup information etc) can stay shared among multiple CPU's.

This finishes off some of the details of all the scalability patches
merged during the merge window.

Also don't mark dentry_kill() for inlining, since it's the uncommon path
and inlining it just makes the common path slower due to extra function
entry/exit overhead.

Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

i915: fix compiler warning

The last i915 drm update brought with it this annoying warning

  drivers/gpu/drm/i915/intel_crt.c: In function ‘intel_crt_get_config’:
  drivers/gpu/drm/i915/intel_crt.c:110:21: warning: unused variable ‘dev’ [-Wunused-variable]
    struct drm_device *dev = encoder->base.dev;
                       ^

introduced by commit 7195a50b5c7e ("drm/i915: Add HSW CRT output readout
support").

Remove the offending pointless variable.

Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Merge branch 'core-urgent-for-linus' of git://git./linux/kernel/git/tip/tip

Pull NUMA balancing memory corruption fixes from Ingo Molnar:
"So these fixes are definitely not something I'd like to sit on, but as
  I said to Mel at the KS the timing is quite tight, with Linus planning
  v3.12-final within a week.

  Fedora-19 is affected:

   comet:~> grep NUMA_BALANCING /boot/config-3.11.3-201.fc19.x86_64

   CONFIG_ARCH_SUPPORTS_NUMA_BALANCING=y
   CONFIG_NUMA_BALANCING_DEFAULT_ENABLED=y
   CONFIG_NUMA_BALANCING=y

  AFAICS Ubuntu will be affected as well, once it updates the kernel:

   hubble:~> grep NUMA_BALANCING /boot/config-3.8.0-32-generic

   CONFIG_ARCH_SUPPORTS_NUMA_BALANCING=y
   CONFIG_NUMA_BALANCING_DEFAULT_ENABLED=y
   CONFIG_NUMA_BALANCING=y

  These 6 commits are a minimalized set of cherry-picks needed to fix
  the memory corruption bugs.  All commits are fixes, except "mm: numa:
  Sanitize task_numa_fault() callsites" which is a cleanup that made two
  followup fixes simpler.

  I've done targeted testing with just this SHA1 to try to make sure
  there are no cherry-picking artifacts.  The original non-cherry-picked
  set of fixes were exposed to linux-next for a couple of weeks"

* 'core-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  mm: Account for a THP NUMA hinting update as one PTE update
  mm: Close races between THP migration and PMD numa clearing
  mm: numa: Sanitize task_numa_fault() callsites
  mm: Prevent parallel splits during THP migration
  mm: Wait for THP migrations to complete during NUMA hinting faults
  mm: numa: Do not account for a hinting fault if we raced

Merge branch 'for-linus' of git://git./linux/kernel/git/dtor/input

Pull input updates from Dmitry Torokhov:
"A bit later than I would want, but the changes are very minor - a few
  new device IDs for new hardware in existing drivers, fix for battery
  in Wacom devices not be considered system battery and cause emergency
  hibernations, and a couple of other bug fixes"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
  Input: ALPS - add support for model found on Dell XT2
  Input: wacom - add support for ISDv4 0x10E sensor
  Input: wacom - add support for ISDv4 0x10F sensor
  Input: wacom - export battery scope
  Input: cm109 - convert high volume dev_err() to dev_err_ratelimited()
  Input: move name/timer init to input_alloc_dev()
  Input: i8042 - i8042_flush fix for a full 8042 buffer
  Input: pxa27x_keypad - fix NULL pointer dereference

Merge tag 'pm+acpi-3.12-late' of git://git./linux/kernel/git/rafael/linux-pm

Pull ACPI and power management fixes from Rafael J Wysocki:
"Last-minute ACPI and power management fixes for 3.12

   - Revert epoll and select commits related to the freezer, introduced
     during the 3.11 cycle, that cause mysterious user space breakage to
     occur during resume from suspend to RAM for multiple users of
     32-bit x86 systems.  Material for 3.11.y stable kernels.

   - Revert a recent ACPI-based PCI hotplug (ACPIPHP) commit that was
     part of boot problem fixes for one machine, but turns out to cause
     issues with hotplug on Thunderbolt chains with multiple devices.
     It also turns out to be unnecessary after another fix in the same
     area that went in later.  From Mika Westerberg"

* tag 'pm+acpi-3.12-late' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
  Revert "ACPI / hotplug / PCI: Avoid doing too much for spurious notifies"
  Revert "select: use freezable blocking call"
  Revert "epoll: use freezable blocking call"

ALSA: fix oops in snd_pcm_info() caused by ASoC DPCM

Unable to handle kernel NULL pointer dereference at virtual address 00000008
pgd = d5300000
[00000008] *pgd=0d265831, *pte=00000000, *ppte=00000000
Internal error: Oops: 17 [#1] PREEMPT ARM
CPU: 0 PID: 2295 Comm: vlc Not tainted 3.11.0+ #755
task: dee74800 ti: e213c000 task.ti: e213c000
PC is at snd_pcm_info+0xc8/0xd8
LR is at 0x30232065
pc : [<c031b52c>]    lr : [<30232065>]    psr: a0070013
sp : e213dea8  ip : d81cb0d0  fp : c05f7678
r10: c05f7770  r9 : fffffdfd  r8 : 00000000
r7 : d8a968a8  r6 : d8a96800  r5 : d8a96200  r4 : d81cb000
r3 : 00000000  r2 : d81cb000  r1 : 00000001  r0 : d8a96200
Flags: NzCv  IRQs on  FIQs on  Mode SVC_32  ISA ARM  Segment user
Control: 10c5387d  Table: 15300019  DAC: 00000015
Process vlc (pid: 2295, stack limit = 0xe213c248)
[<c031b52c>] (snd_pcm_info) from [<c031b570>] (snd_pcm_info_user+0x34/0x9c)
[<c031b570>] (snd_pcm_info_user) from [<c03164a4>] (snd_pcm_control_ioctl+0x274/0x280)
[<c03164a4>] (snd_pcm_control_ioctl) from [<c0311458>] (snd_ctl_ioctl+0xc0/0x55c)
[<c0311458>] (snd_ctl_ioctl) from [<c00eca84>] (do_vfs_ioctl+0x80/0x31c)
[<c00eca84>] (do_vfs_ioctl) from [<c00ecd5c>] (SyS_ioctl+0x3c/0x60)
[<c00ecd5c>] (SyS_ioctl) from [<c000e500>] (ret_fast_syscall+0x0/0x48)
Code: e1a00005 e59530dc e3a01001 e1a02004 (e5933008)
---[ end trace cb3d9bdb8dfefb3c ]---

This is provoked when the ASoC front end is open along with its backend,
(which causes the backend to have a runtime assigned to it) and then the
SNDRV_CTL_IOCTL_PCM_INFO is requested for the (visible) backend device.

Resolve this by ensuring that ASoC internal backend devices are not
visible to userspace, just as the commentry for snd_pcm_new_internal()
says it should be.

Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Mark Brown <broonie@linaro.org>
Cc: <stable@vger.kernel.org> [v3.4+]
Signed-off-by: Takashi Iwai <tiwai@suse.de>

MIPS: ralink: fix return value check in rt_timer_probe()

In case of error, the function devm_request_and_ioremap() returns NULL
pointer not ERR_PTR(). Fix it by using devm_ioremap_resource() instead
of devm_request_and_ioremap().

Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Acked-by: John Crispin <blogic@openwrt.org>
Cc: grant.likely@linaro.org
Cc: rob.herring@calxeda.com
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/6098/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

Input: ALPS - add support for model found on Dell XT2

This patch adds support for touchpad found on Dell XT2. It's a dual device
with device ID: 73, 00, 14, that comply with "ALPS_PROTO_V2".

Signed-off-by: Yunkang Tang <yunkang.tang@cn.alps.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Merge branch 'drm-fixes-3.12' of git://people.freedesktop.org/~agd5f/linux into drm-fixes

Just a few small fixes for radeon (audio regression fix,
stability fix, and an endian bug noticed by coverity).

* 'drm-fixes-3.12' of git://people.freedesktop.org/~agd5f/linux:
  drm/radeon/dpm: fix incompatible casting on big endian
  drm/radeon: disable bapm on KB
  drm/radeon: use sw CTS/N values for audio on DCE4+

Merge branch 'akpm' (fixes from Andrew Morton)

Merge three fixes from Andrew Morton.

* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
  memcg: use __this_cpu_sub() to dec stats to avoid incorrect subtrahend casting
  percpu: fix this_cpu_sub() subtrahend casting for unsigneds
  mm/pagewalk.c: fix walk_page_range() access of wrong PTEs

memcg: use __this_cpu_sub() to dec stats to avoid incorrect subtrahend casting

As of commit 3ea67d06e467 ("memcg: add per cgroup writeback pages
accounting") memcg counter errors are possible when moving charged
memory to a different memcg.  Charge movement occurs when processing
writes to memory.force_empty, moving tasks to a memcg with
memcg.move_charge_at_immigrate=1, or memcg deletion.

An example showing error after memory.force_empty:

  $ cd /sys/fs/cgroup/memory
  $ mkdir x
  $ rm /data/tmp/file
  $ (echo $BASHPID >> x/tasks && exec mmap_writer /data/tmp/file 1M) &
  [1] 13600
  $ grep ^mapped x/memory.stat
  mapped_file 1048576
  $ echo 13600 > tasks
  $ echo 1 > x/memory.force_empty
  $ grep ^mapped x/memory.stat
  mapped_file 4503599627370496

mapped_file should end with 0.
  4503599627370496 == 0x10,0000,0000,0000 == 0x100,0000,0000 pages
  1048576          == 0x10,0000           == 0x100 pages

This issue only affects the source memcg on 64 bit machines; the
destination memcg counters are correct.  So the rmdir case is not too
important because such counters are soon disappearing with the entire
memcg.  But the memcg.force_empty and memory.move_charge_at_immigrate=1
cases are larger problems as the bogus counters are visible for the
(possibly long) remaining life of the source memcg.

The problem is due to memcg use of __this_cpu_from(.., -nr_pages), which
is subtly wrong because it subtracts the unsigned int nr_pages (either
-1 or -512 for THP) from a signed long percpu counter.  When
nr_pages=-1, -nr_pages=0xffffffff.  On 64 bit machines stat->count[idx]
is signed 64 bit.  So memcg's attempt to simply decrement a count (e.g.
from 1 to 0) boils down to:

  long count = 1
  unsigned int nr_pages = 1
  count += -nr_pages  /* -nr_pages == 0xffff,ffff */
  count is now 0x1,0000,0000 instead of 0

The fix is to subtract the unsigned page count rather than adding its
negation.  This only works once "percpu: fix this_cpu_sub() subtrahend
casting for unsigneds" is applied to fix this_cpu_sub().

Signed-off-by: Greg Thelen <gthelen@google.com>
Acked-by: Tejun Heo <tj@kernel.org>
Acked-by: Johannes Weiner <hannes@cmpxchg.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

percpu: fix this_cpu_sub() subtrahend casting for unsigneds

this_cpu_sub() is implemented as negation and addition.

This patch casts the adjustment to the counter type before negation to
sign extend the adjustment.  This helps in cases where the counter type
is wider than an unsigned adjustment.  An alternative to this patch is
to declare such operations unsupported, but it seemed useful to avoid
surprises.

This patch specifically helps the following example:
  unsigned int delta = 1
  preempt_disable()
  this_cpu_write(long_counter, 0)
  this_cpu_sub(long_counter, delta)
  preempt_enable()

Before this change long_counter on a 64 bit machine ends with value
0xffffffff, rather than 0xffffffffffffffff.  This is because
this_cpu_sub(pcp, delta) boils down to this_cpu_add(pcp, -delta),
which is basically:
  long_counter = 0 + 0xffffffff

Also apply the same cast to:
  __this_cpu_sub()
  __this_cpu_sub_return()
  this_cpu_sub_return()

All percpu_test.ko passes, especially the following cases which
previously failed:

  l -= ui_one;
  __this_cpu_sub(long_counter, ui_one);
  CHECK(l, long_counter, -1);

  l -= ui_one;
  this_cpu_sub(long_counter, ui_one);
  CHECK(l, long_counter, -1);
  CHECK(l, long_counter, 0xffffffffffffffff);

  ul -= ui_one;
  __this_cpu_sub(ulong_counter, ui_one);
  CHECK(ul, ulong_counter, -1);
  CHECK(ul, ulong_counter, 0xffffffffffffffff);

  ul = this_cpu_sub_return(ulong_counter, ui_one);
  CHECK(ul, ulong_counter, 2);

  ul = __this_cpu_sub_return(ulong_counter, ui_one);
  CHECK(ul, ulong_counter, 1);

Signed-off-by: Greg Thelen <gthelen@google.com>
Acked-by: Tejun Heo <tj@kernel.org>
Acked-by: Johannes Weiner <hannes@cmpxchg.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

mm/pagewalk.c: fix walk_page_range() access of wrong PTEs

When walk_page_range walk a memory map's page tables, it'll skip
VM_PFNMAP area, then variable 'next' will to assign to vma->vm_end, it
maybe larger than 'end'.  In next loop, 'addr' will be larger than
'next'.  Then in /proc/XXXX/pagemap file reading procedure, the 'addr'
will growing forever in pagemap_pte_range, pte_to_pagemap_entry will
access the wrong pte.

  BUG: Bad page map in process procrank  pte:8437526f pmd:785de067
  addr:9108d000 vm_flags:00200073 anon_vma:f0d99020 mapping:  (null) index:9108d
  CPU: 1 PID: 4974 Comm: procrank Tainted: G    B   W  O 3.10.1+ #1
  Call Trace:
    dump_stack+0x16/0x18
    print_bad_pte+0x114/0x1b0
    vm_normal_page+0x56/0x60
    pagemap_pte_range+0x17a/0x1d0
    walk_page_range+0x19e/0x2c0
    pagemap_read+0x16e/0x200
    vfs_read+0x84/0x150
    SyS_read+0x4a/0x80
    syscall_call+0x7/0xb

Signed-off-by: Liu ShuoX <shuox.liu@intel.com>
Signed-off-by: Chen LinX <linx.z.chen@intel.com>
Acked-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Reviewed-by: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com>
Cc: <stable@vger.kernel.org> [3.10.x+]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

mm: list_lru: fix almost infinite loop causing effective livelock

I've seen a fair number of issues with kswapd and other processes
appearing to get stuck in v3.12-rc.  Using sysrq-p many times seems to
indicate that it gets stuck somewhere in list_lru_walk_node(), called
from prune_icache_sb() and super_cache_scan().

I never seem to be able to trigger a calltrace for functions above that
point.

So I decided to add the following to super_cache_scan():

    @@ -81,10 +81,14 @@ static unsigned long super_cache_scan(struct shrinker *shrink,
            inodes = list_lru_count_node(&sb->s_inode_lru, sc->nid);
            dentries = list_lru_count_node(&sb->s_dentry_lru, sc->nid);
            total_objects = dentries + inodes + fs_objects + 1;
    +printk("%s:%u: %s: dentries %lu inodes %lu total %lu\n", current->comm, current->pid, __func__, dentries, inodes, total_objects);

            /* proportion the scan between the caches */
            dentries = mult_frac(sc->nr_to_scan, dentries, total_objects);
            inodes = mult_frac(sc->nr_to_scan, inodes, total_objects);
    +printk("%s:%u: %s: dentries %lu inodes %lu\n", current->comm, current->pid, __func__, dentries, inodes);
    +BUG_ON(dentries == 0);
    +BUG_ON(inodes == 0);

            /*
             * prune the dcache first as the icache is pinned by it, then
    @@ -99,7 +103,7 @@ static unsigned long super_cache_scan(struct shrinker *shrink,
                    freed += sb->s_op->free_cached_objects(sb, fs_objects,
                                                           sc->nid);
            }
    -
    +printk("%s:%u: %s: dentries %lu inodes %lu freed %lu\n", current->comm, current->pid, __func__, dentries, inodes, freed);
            drop_super(sb);
            return freed;
     }

and shortly thereafter, having applied some pressure, I got this:

    update-apt-xapi:1616: super_cache_scan: dentries 25632 inodes 2 total 25635
    update-apt-xapi:1616: super_cache_scan: dentries 1023 inodes 0
    ------------[ cut here ]------------
    Kernel BUG at c0101994 [verbose debug info unavailable]
    Internal error: Oops - BUG: 0 [#3] SMP ARM
    Modules linked in: fuse rfcomm bnep bluetooth hid_cypress
    CPU: 0 PID: 1616 Comm: update-apt-xapi Tainted: G      D      3.12.0-rc7+ #154
    task: daea1200 ti: c3bf8000 task.ti: c3bf8000
    PC is at super_cache_scan+0x1c0/0x278
    LR is at trace_hardirqs_on+0x14/0x18
    Process update-apt-xapi (pid: 1616, stack limit = 0xc3bf8240)
    ...
    Backtrace:
      (super_cache_scan) from [<c00cd69c>] (shrink_slab+0x254/0x4c8)
      (shrink_slab) from [<c00d09a0>] (try_to_free_pages+0x3a0/0x5e0)
      (try_to_free_pages) from [<c00c59cc>] (__alloc_pages_nodemask+0x5)
      (__alloc_pages_nodemask) from [<c00e07c0>] (__pte_alloc+0x2c/0x13)
      (__pte_alloc) from [<c00e3a70>] (handle_mm_fault+0x84c/0x914)
      (handle_mm_fault) from [<c001a4cc>] (do_page_fault+0x1f0/0x3bc)
      (do_page_fault) from [<c001a7b0>] (do_translation_fault+0xac/0xb8)
      (do_translation_fault) from [<c000840c>] (do_DataAbort+0x38/0xa0)
      (do_DataAbort) from [<c00133f8>] (__dabt_usr+0x38/0x40)

Notice that we had a very low number of inodes, which were reduced to
zero my mult_frac().

Now, prune_icache_sb() calls list_lru_walk_node() passing that number of
inodes (0) into that as the number of objects to scan:

    long prune_icache_sb(struct super_block *sb, unsigned long nr_to_scan,
                         int nid)
    {
            LIST_HEAD(freeable);
            long freed;

            freed = list_lru_walk_node(&sb->s_inode_lru, nid, inode_lru_isolate,
                                           &freeable, &nr_to_scan);

which does:

    unsigned long
    list_lru_walk_node(struct list_lru *lru, int nid, list_lru_walk_cb isolate,
                       void *cb_arg, unsigned long *nr_to_walk)
    {

            struct list_lru_node    *nlru = &lru->node[nid];
            struct list_head *item, *n;
            unsigned long isolated = 0;

            spin_lock(&nlru->lock);
    restart:
            list_for_each_safe(item, n, &nlru->list) {
                    enum lru_status ret;

                    /*
                     * decrement nr_to_walk first so that we don't livelock if we
                     * get stuck on large numbesr of LRU_RETRY items
                     */
                    if (--(*nr_to_walk) == 0)
                            break;

So, if *nr_to_walk was zero when this function was entered, that means
we're wanting to operate on (~0UL)+1 objects - which might as well be
infinite.

Clearly this is not correct behaviour.  If we think about the behaviour
of this function when *nr_to_walk is 1, then clearly it's wrong - we
decrement first and then test for zero - which results in us doing
nothing at all.  A post-decrement would give the desired behaviour -
we'd try to walk one object and one object only if *nr_to_walk were one.

It also gives the correct behaviour for zero - we exit at this point.

Fixes: 5cedf721a7cd ("list_lru: fix broken LRU_RETRY behaviour")
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Cc: Dave Chinner <dchinner@redhat.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Andrew Morton <akpm@linux-foundation.org>
[ Modified to make sure we never underflow the count: this function gets
  called in a loop, so the 0 -> ~0ul transition is dangerous  - Linus ]
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Merge tag 'tty-3.12-rc8' of git://git./linux/kernel/git/gregkh/tty

Pull serial fixes from Greg KH:
"Here are 3 tiny fixes that are needed for 3.12-final for some serial
  drivers.

  One of them is a revert of a broken patch, and two others are fixes
  for reported bugs.  All of these have been in linux-next for a while,
  I forgot I had not sent them to you yet, my fault"

(Actually, Greg, you _had_ sent two of the three, so this pulls in just
one actual new fix)

* tag 'tty-3.12-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
  tty/serial: at91: fix uart/usart selection for older products

Merge branch 'drm-fixes' of git://people.freedesktop.org/~airlied/linux

Pull drm fixes from Dave Airlie:
"Mainly Intel regression fixes and quirks, along with a simple one
  liner to fix rendernodes ioctl access (off by default, but testers
  want to test it)"

* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
  drm: allow DRM_IOCTL_VERSION on render-nodes
  drm/i915: Fix the PPT fdi lane bifurcate state handling on ivb
  drm/i915: No LVDS hardware on Intel D410PT and D425KT
  drm/i915/dp: workaround BIOS eDP bpp clamping issue
  drm/i915: Add HSW CRT output readout support
  drm/i915: Add support for pipe_bpp readout

Merge tag 'sound-3.12' of git://git./linux/kernel/git/tiwai/sound

Pull sound fixes from Takashi Iwai:
"A few small HD-audio regression fixes, mostly for stable kernels, too"

* tag 'sound-3.12' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
  ALSA: hda - Fix silent headphone on Thinkpads with AD1984A codec
  ALSA: hda - Add missing initial vmaster hook at build_controls callback
  ALSA: hda - Fix unbalanced runtime PM refcount after S3/S4

Merge tag 'for-linus' of git://git./virt/kvm/kvm

Pull KVM fixes from Paolo Bonzini:
"Fixes for the 3.12 debugfs problem - removing the duplicate directory
  name, and using a better the error code"

* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
  KVM: use a more sensible error number when debugfs directory creation fails
  KVM: Fix modprobe failure for kvm_intel/kvm_amd

Staging: sb105x: info leak in mp_get_count()

The icount.reserved[] array isn't initialized so it leaks stack
information to userspace.

Reported-by: Nico Golde <nico@ngolde.de>
Reported-by: Fabian Yamaguchi <fabs@goesec.de>
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Cc: stable@kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Staging: bcm: info leak in ioctl

The DevInfo.u32Reserved[] array isn't initialized so it leaks kernel
information to user space.

Reported-by: Nico Golde <nico@ngolde.de>
Reported-by: Fabian Yamaguchi <fabs@goesec.de>
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Cc: stable@kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

staging: wlags49_h2: buffer overflow setting station name

We need to check the length parameter before doing the memcpy(). I've
actually changed it to strlcpy() as well so that it's NUL terminated.

You need CAP_NET_ADMIN to trigger these so it's not the end of the
world.

Reported-by: Nico Golde <nico@ngolde.de>
Reported-by: Fabian Yamaguchi <fabs@goesec.de>
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Cc: stable@kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

aacraid: missing capable() check in compat ioctl

In commit d496f94d22d1 ('[SCSI] aacraid: fix security weakness') we
added a check on CAP_SYS_RAWIO to the ioctl. The compat ioctls need the
check as well.

Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Cc: stable@kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

staging: ozwpan: prevent overflow in oz_cdev_write()

We need to check "count" so we don't overflow the ei->data buffer.

Reported-by: Nico Golde <nico@ngolde.de>
Reported-by: Fabian Yamaguchi <fabs@goesec.de>
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Cc: stable@kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

uml: check length in exitcode_proc_write()

We don't cap the size of buffer from the user so we could write past the
end of the array here. Only root can write to this file.

Reported-by: Nico Golde <nico@ngolde.de>
Reported-by: Fabian Yamaguchi <fabs@goesec.de>
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Cc: stable@kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Merge tag 'asoc-fix-v3.12-rc7' of git://git./linux/kernel/git/broonie/sound into for-linus

ASoC: Fixes for v3.12

A few of the Coverity fixes from Takashi, one of which (the wm_hubs one)
is particularly noticable.

Merge remote-tracking branch 'asoc/fix/wm8994' into asoc-linus

ASoC: wm_hubs: Add missing break in hp_supply_event()

Spotted by coverity CID 115170.

Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
Cc: stable@vger.kernel.org

MIPS: malta: Fix GIC interrupt offsets

The GIC interrupt offsets are calculated based on the value of NR_CPUS.
However, this is wrong because NR_CPUS may or may not contain the real
number of the actual cpus present in the system. We fix that by using
the 'nr_cpu_ids' variable which contains the real number of cpus in
the system. Previously, an MT core (eg with 8 VPEs) will fail to boot if
NR_CPUS was > 8 with the following errors:

------------[ cut here ]------------
WARNING: CPU: 0 PID: 0 at kernel/irq/chip.c:670 __irq_set_handler+0x15c/0x164()
Modules linked in:
CPU: 0 PID: 0 Comm: swapper/0 Tainted: G        W    3.12.0-rc5-00087-gced5633 5
Stack : 00000006 00000004 00000000 00000000 00000000 00000000 807a4f36 00000053
          807a0000 00000000 80173218 80565aa8 00000000 00000000 00000000 0000000
          00000000 00000000 00000000 00000000 00000000 00000000 00000000 0000000
          00000000 00000000 00000000 8054fd00 8054fd94 80500514 805657a7 8016eb4
          807a0000 80500514 00000000 00000000 80565aa8 8079a5d8 80565766 8054fd0
          ...
Call Trace:
[<801098c0>] show_stack+0x64/0x7c
[<8049c6b0>] dump_stack+0x64/0x84
[<8012efc4>] warn_slowpath_common+0x84/0xb4
[<8012f00c>] warn_slowpath_null+0x18/0x24
[<80173218>] __irq_set_handler+0x15c/0x164
[<80587cf4>] arch_init_ipiirq+0x2c/0x3c
[<805880c8>] arch_init_irq+0x3c4/0x4bc
[<80588e28>] init_IRQ+0x3c/0x50
[<805847e8>] start_kernel+0x230/0x3d8

---[ end trace 4eaa2a86a8e2da26 ]---

This is now fixed and the Malta board can boot with any NR_CPUS value
which also helps supporting more processors in a single kernel binary.

Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/6091/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

Revert "ACPI / hotplug / PCI: Avoid doing too much for spurious notifies"

Commit 2dc4128 (ACPI / hotplug / PCI: Avoid doing too much for
spurious notifies) changed the enable_slot() to check return value of
pci_scan_slot() and if it is zero return early from the function. It
means that there were no new devices in this particular slot.

However, if a device appeared deeper in the hierarchy the code now
ignores it causing things like Thunderbolt chaining fail to recognize
new devices.

The problem with Alex Williamson's machine was solved with commit
a47d8c8 (ACPI / hotplug / PCI: Avoid parent bus rescans on spurious
device checks) and hence we should be able to restore the original
functionality that we always rescan on bus check notification.

On a device check notification we still check what acpiphp_rescan_slot()
returns and on zero bail out early.

Fixes: 2dc41281b1d1 (ACPI / hotplug / PCI: Avoid doing too much for spurious notifies)
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Tested-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>

Revert "select: use freezable blocking call"

This reverts commit 9745cdb36da8 (select: use freezable blocking call)
that triggers problems during resume from suspend to RAM on Paul Bolle's
32-bit x86 machines.  Paul says:

  Ever since I tried running (release candidates of) v3.11 on the two
  working i686s I still have lying around I ran into issues on resuming
  from suspend. Reverting 9745cdb36da8 (select: use freezable blocking
  call) resolves those issues.

  Resuming from suspend on i686 on (release candidates of) v3.11 and
  later triggers issues like:

  traps: systemd[1] general protection ip:b738e490 sp:bf882fc0 error:0 in libc-2.16.so[b731c000+1b0000]

  and

  traps: rtkit-daemon[552] general protection ip:804d6e5 sp:b6cb32f0 error:0 in rtkit-daemon[8048000+d000]

  Once I hit the systemd error I can only get out of the mess that the
  system is at that point by power cycling it.

Since we are reverting another freezer-related change causing similar
problems to happen, this one should be reverted as well.

References: https://lkml.org/lkml/2013/10/29/583
Reported-by: Paul Bolle <pebolle@tiscali.nl>
Fixes: 9745cdb36da8 (select: use freezable blocking call)
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Cc: 3.11+ <stable@vger.kernel.org> # 3.11+

Revert "epoll: use freezable blocking call"

This reverts commit 1c441e921201 (epoll: use freezable blocking call)
which is reported to cause user space memory corruption to happen
after suspend to RAM.

Since it appears to be extremely difficult to root cause this
problem, it is best to revert the offending commit and try to address
the original issue in a better way later.

References: https://bugzilla.kernel.org/show_bug.cgi?id=61781
Reported-by: Natrio <natrio@list.ru>
Reported-by: Jeff Pohlmeyer <yetanothergeek@gmail.com>
Bisected-by: Leo Wolf <jclw@ymail.com>
Fixes: 1c441e921201 (epoll: use freezable blocking call)
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Cc: 3.11+ <stable@vger.kernel.org> # 3.11+

ALSA: hda - Add a fixup for ASUS N76VZ

ASUS N76VZ needs the same fixup as N56VZ for supporting the boost
speaker.

Bugzilla: https://bugzilla.novell.com/show_bug.cgi?id=846529
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>

KVM: use a more sensible error number when debugfs directory creation fails

I don't know if this was due to cut and paste, or somebody was really
using a D20 to pick the error code for kvm_init_debugfs as suggested by
Linus (EFAULT is 14, so the possibility cannot be entirely ruled out).

In any case, this patch fixes it.

Reported-by: Tim Gardner <tim.gardner@canonical.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>