libertas: convert SET_WEP to a direct command

Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

libertas: convert SLEEP_PARAMS to a direct command

Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

libertas: convert INACTIVITY_TIMEOUT to a direct command

Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

libertas: convert RADIO_CONTROL to a direct command

Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

libertas: submit RSSI command on tx timeout, to check whether module is dead

We don't necessarily want to reset the device on a TX timeout. But more
often than not, the real cause is that the firmware has crapped itself,
not just that the network is busy. So submit any harmless command, and
if _that_ times out, then the error handling code will reset the module,
as appropriate.

Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

libertas: make lbs_submit_command always 'succeed' and set command timer

Even if it fails, we want to wait a while and try again, with an
ultimate timeout if it the condition persists. So again, just use the
standard command timeout behaviour.

Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

libertas: discard DEFER responses to commands; let the timeout trigger

When the firmware returns 0x0004, it wants us to try again later. We can
achieve that simply by throwing out the response and letting the command
timeout code kick in.

Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

libertas: use priv->upld_buf for command responses

If we don't scribble over the command we sent, then we can retry it when
the firmware responds with 0x0004 (which means -EAGAIN).

Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

libertas: reduce explicit references to priv->cur_cmd->cmdbuf

We have a local variable 'resp' which we use for this. So use it,
instead of typing the whole thing.

In preparation for actually using priv->upld_buf for the responses
instead...

Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

libertas: Check for PS mode support on USB devices

Move the various firmware setup bits into a separate function, which
used to do just boot2 version.

Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

libertas: allow for PS mode to be disabled when firmware doesn't support it

Otherwise, we go into an endless busy loop trying to enable PS mode when
the command queue is empty, dealing with the error response, and then
trying to enable PS mode again because the command queue is empty.... it
doesn't really save much power.

Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

libertas: handle HOST_AWAKE event by sending WAKEUP_CONFIRM command

lbs_send_confirmwake() is a bit ugly but matches the way we confirm
sleep. We'll deal with that whole thing later.

Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

libertas: don't clear priv->dnld_sent after sending sleep confirm

DNLD_RES_RECEIVED is a bit of a misnomer -- we never wait for the result
to be received; it's purely representing the state of the TX path, and
in this case the TX path is definitely busy.

Of course, that means that we don't actually care about DATA_SENT vs.
CMD_SENT either, but that's a can of worms for another day...

Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

libertas: fix buffer handling of PS_MODE commands and responses

Commit 5b8845345e7385d2eb37fac22ba9ab6905988be5 (or, in case the git
workflow is broken and patches get recommitted, the commit entitled
'libertas: rename and re-type bufvirtualaddr to cmdbuf' by dcbw),
introduced a number of bugs where we once had a pointer to a command
_payload_, but now we use the pointer to the command header instead.

The fix isn't wonderfully pretty for now, but it'll get better when we
finish converting all commands so the structures include the header.

Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

libertas: add SLEEP_PERIOD and FW_WAKE_METHOD command definitions

Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

libertas: fix return from lbs_update_channel()

If we return the channel number in a 'ret' variable where anything
non-zero is later interpreted as an error, that isn't nice. It breaks
WPA, for a start. OLPC trac #5485

Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

libertas: kill 'addtail' argument to lbs_queue_cmd() and make it static

Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

libertas: handle command timeout in main thread instead of directly in timer

And handle the case where it times out more than once, too, instead of
locking up for ever.

Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

libertas: ensure response buffer size is always set for lbs_cmd_with_response

Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

libertas: add __lbs_cmd_async() for asynchronous command submission

Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

libertas: store command result in cmdnode instead of priv->cur_cmd_retcode

... at least for users of __lbs_cmd().

Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

libertas: kill pdata_buf member of struct cmd_ctrl_node

We can use the callback_arg for it; that's the way we're heading anyway...

Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

libertas: let __lbs_cmd() free its own cmdnode

Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

libertas: kill cleanup_cmdnode()

Move the wakeup into lbs_complete_command(), and leave the other bits
in __lbs_cleanup_and_insert_cmd() which was the only caller now anyway.

There are two remaining direct callers of lbs_cleanup_and_insert_cmd(),
and they are both fine without the wakeup.

Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

libertas: don't re-initialise cmdnode when taking it off the free queue

We initialise it when we add it to the queue. No need to do it again.

Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

libertas: introduce and use lbs_complete_command() for command completion

Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

libertas: remove some pointless checks for cmdnode buffer being present

We allocate them all at the same time, at startup. If they go missing,
we have more serious things to worry about, and the resulting oops will
be a perfectly acceptable result.

Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

libertas: don't use __lbs_cmd() with empty callback in if_usb.c

We're about to change semantics, leaving callers of
lbs_prepare_and_send_command() with the old broken priv->cur_cmd_retcode
crap. The existence of the callback command will be the trigger for the
new semantics when handling the response.

Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

libertas: rename and clean up DownloadcommandToStation

Call it lbs_submit_command(), remove a bunch of things which can be (or,
in the case of zeroing ->cmdwaitqwoken, already are) done elsewhere.

Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

libertas: kill unused wait_option field in struct cmd_ctrl_node

Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

libertas: kill whitespace at end of lines

Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

libertas: clean up if_usb driver

It was just getting on my tits, really.

Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

libertas: stop attempting to reset devices on unload

It wasn't working anyway -- by the time we get into if_usb_disconnect()
the USB core has already stopped us talking to the thing; even if it's
just on unload and the device still exists.

Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

libertas: don't exit worker thread until kthread_stop() is called

The kthread code can't cope with a thread exiting of its own accord and
then someone calling kthread_stop() for it. When the thread detects that
it needs to die, make it wait for kthread_stop() to be called.

Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

b43legacy: Fix rfkill radio LED

This fixes Bug #9414 for b43legacy. This patch is the equivalent of one
submitted earlier for b43.

Since addition of the rfkill callback, the LED associated with the off
switch on the radio has not worked for several reasons:

(1) Essential data in the rfkill structure were missing.
(2) The rfkill structure was initialized after the LED initialization.
(3) There was a minor memory leak if the radio LED structure was inited.

Once the above problems were fixed, additional difficulties were noted:

(4) The radio LED was in the wrong state at startup.
(5) The radio switch had to be manipulated twice for each state change.
(6) A circular mutex locking situation existed.
(7) If rfkill-input is built as a module, it is not automatically loaded.

This patch fixes all of the above and removes a couple of sparse warnings.

Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Stefano Brivio <stefano.brivio@polimi.it>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

S2io: Fixes to enable multiple transmit fifos

Multiple transmit fifo initialization -
  - Assigned equal scheduling priority for all configured FIFO's.
  - Modularized transmit traffic interrupt initialization since it is executed in
    s2io_card_up and s2io_link. Enable continuous tx interrupt when link is UP
    and vice verse.
  - Enable transmit interrupts for all configured transmit fifos.
  - Fixed typo errors.

Signed-off-by: Surjit Reang <surjit.reang@neterion.com>
Signed-off-by: Sreenivasa Honnur <sreenivasa.honnur@neterion.com>
Signed-off-by: Ramkrishna Vepa <ram.vepa@neterion.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

S2io: Fixes to enable multiple transmit fifo support

Fixes to enable multiple transmit fifos (upto a maximum of eight).
  - Moved single tx_lock from struct s2io_nic to struct fifo_info.
  - Moved single ufo_in_band_v structure from struct s2io_nic to struct
    fifo_info.
  - Assign the respective interrupt number for the transmitting fifo in the
    transmit descriptor (TXD).
- Added boundary checks for number of FIFOs enabled and FIFO length.

Signed-off-by: Surjit Reang <surjit.reang@neterion.com>
Signed-off-by: Sreenivasa Honnur <sreenivasa.honnur@neterion.com>
Signed-off-by: Ramkrishna Vepa <ram.vepa@neterion.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

cxgb3 - Fix EEH, missing softirq blocking

set_pci_drvdata() stores a pointer to the adapter,
not the net device.
Add missing softirq blocking in t3_mgmt_tx.

Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

cxgb3 - parity initialization for T3C adapters.

Add parity initialization for T3C adapters.

Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

pasemi: export pasemi_dma_init()

Forgot to export this one. Needed when pasemi_mac is compiled as a module.

Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

PLIP driver: convert the semaphore killed_timer_sem to completion

Signed-off-by: Matthias Kaehlcke <matthias.kaehlcke@gmail.com>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

bnx2x depends on ZLIB_INFLATE

The bnx2x module depends on the zlib_inflate functions.  The build will
fail if ZLIB_INFLATE has not been selected manually or by building another
module that automatically selects it.

Modify BNX2X config option to 'select ZLIB_INFLATE' like BNX2
and others.  This seems to fix it.

Signed-off-by: Lee Schermerhorn <lee.schermerhorn@hp.com>
Acked-by: Eliezer Tamir <eliezert@broadcom.com>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

pcmcia net: use roundup_pow_of_two() macro instead of grotesque loop

Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

e1000: Dump the eeprom when a user encounters a bad checksum

To help supporting users with a bad eeprom checksum, dump the
eeprom info when such a situation is encountered by a user.

Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

ixgb: enable sun hardware support for broadcom phy

Implement support for a SUN-specific PHY.

SUN provides a modified 82597-based board with their own
PHY that works with very little modification to the code. This
patch implements this new PHY which is identified by the
subvendor device ID. The device ID of the adapter remains
the same.

Signed-off-by: Matheos Worku <matheos.worku@sun.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

e1000: remove no longer used code for pci read/write cfg

Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

ixgb endianness annotations

Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

ixgbe endianness annotations

Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

e100 endianness annotations

Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

forcedeth endianness bugs

* misannotation: struct register_test members are actually host-endian
* bug: cpu_to_le64(n) >> 32 instead of cpu_to_le32(n >> 32) in setting
->bufhigh and similar for ->buflow (take low bits, _then_ convert to
little-endian, not the other way round).
* bug: setup_hw_rings() should not convert to little-endian at all (we
feed the result to writel(), not store in shared data structure), let
alone try to play with shifting and masking little-endian values.  Introduced
when setup_hw_rings() went in, screwed both 64bit case and the old code for
32bit rings it had replaced.

Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

NULL noise in drivers/net

Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

e1000 endianness annotations

Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

e1000e endianness annotations

Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

sungem endianness annotations\e

Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

sunhme endianness annotations

This one is interesting - SBUS and PCI variants have
opposite endianness in descriptors (SBUS is sparc-only, so there
host-endian == big-endian).

Solution: declare a bitwise type (hme32) and in accessor
helpers do typechecking and force-casts (once we know that the
type is right).

Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

endianness annotations and fixes for olympic

* missing braces in !readl(...) & ...
* trivial endianness annotations
* in olympic_arb_cmd() the loop collecting fragments of
packet is b0rken on big-endian - we have
(next_ptr && (buf_ptr=olympic_priv->olympic_lap + ntohs(next_ptr)))
as condition and it should have swab16(), not ntohs() - it's host-endian
byteswapped, not big-endian.  So if we get more than one fragment on big-endian
host, we get screwed.
This ntohs() got missed back when the rest of those had been switched
to swab16() in 2.4.0-test2-pre1 - at a guess, nobody had hit fragmented
packets during the testing of PPC fixes.

PS: Ken Aaker cc'd on assumption that he is the same guy who'd done the
original set of PPC fixes in olympic

Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

libertas: use spin_is_locked() instead of spin_trylock() in lbs_interrupt()

We get scary warnings on UP if we use spin_trylock() and find, as we
hoped, that the lock in question is already locked.

Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

libertas: pass channel argument directly to lbs_mesh_config()

There is weirdness here; the firmware seems to refuse to change channels
at will.

Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

libertas: cope with both old and new mesh TLV values

Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

libertas: make lbs_update_channel() function non-static

We'll want to use this for meshfrobbing

Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

libertas: add ethtool support for wake-on-lan configuration

Also, check that suspend is refused if HOST_SLEEP_CFG hasn't been done.

Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

libertas: implement suspend/resume for USB devices

Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

libertas: implement suspend and resume core methods

We (ab)use priv->fw_ready to stop the worker thread from sending more
commands or data after the response to the HOST_SLEEP_ACTIVATE command
comes in. And we set it from the callback function _directly_ to ensure
that the worker thread sees it immediately; if we did it in
lbs_suspend() after waking up, that might be too late.

Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

libertas: make worker thread not freezable

We want it to send the HOST_SLEEP_ACTIVATE command on the way down...

Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

libertas: switch lbs_cmd() to take a _pointer_ to the command structure

This way, it looks more like a normal function.

Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

libertas: add lbs_host_sleep_cfg() command function

Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

libertas: slight cleanup of netif queue stop/wake

In particular, we shouldn't be waking the queues in lbs_host_to_card_done()
any more.

Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

libertas: add missing newlines in debugging statements

Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

libertas: be more careful about command responses matching cur_cmd

Especially in the light of OLPC trac #5461, in which the firmware starts
sending us seemingly random command responses which bear little relation
to the command we sent it.

Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

libertas: add debugging output to lbs_mesh_config()

Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

libertas: disable mesh temporarily while setting eth channel/assoc

Otherwise the device won't let us change channels.

Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

libertas: add missing newline on debug message

Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

libertas: allow setting channel on mshX device

Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

libertas: allow get/set SSID on mshX device

Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

libertas: whitespace cleanup in host.h

Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

libertas: kill rx_urb_recall and eth_dev members of struct usb_card_rec

Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

libertas: kill references to mesh autostart

Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

libertas: add lbs_mesh sysfs attribute for enabling mesh

Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

libertas: fix sparse endianness warnings in scan.c

Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

libertas: make some more functions static

sparse was getting on my tits.

Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

libertas: endianness fixes for get_channel/set_channel

Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

libertas: convert RF_CHANNEL to a direct command

Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

libertas: convert DATA_RATE to a direct command

Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

libertas: fix case of FWT_ACCESS_LIST_ROUTE and FWT_ACCESS_LIST_NEIGHBOR commands

Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

libertas: remove casts from lbs_cmd() and lbs_cmd_with_response() macros

If stupid people like me give it arguments with the wrong type (like a
pointer to the structure, for example, instead of the structure itself),
then we should probably notice that at compile time. Otherwise, much
confusion ensues.

Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

libertas: convert CMD_MESH_ACCESS to a direct command

Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

libertas: fix debug output in lbs_cmd_copyback() function.

Bad dcbw. Always test on big-endian, or at least use sparse.

Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

libertas: rename and re-type bufvirtualaddr to cmdbuf

Make it a struct cmd_header, since that's what it is, and clean up
the places that it's used.

Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

libertas: wait for 'firmware ready' event from firmware after loading

Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

libertas: move removal of lbs_rtap file to lbs_stop_card()

This prevents us from trying to remove it when it didn't exist, in the
error case.

Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

libertas: switch USB cardp->priv to 'struct lbs_private *' and resulting fix

Amazing what interesting things the compiler will tell you if you let it
know what types you expect to be passing around.

Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

libertas: convert GET_HW_SPEC to a direct command

Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

libertas: add simple copyback command callback

A simple callback which copies the response back into the
command buffer that was used to send the command to the
card.  Will allow for direct command processing outside
the mega-switches in cmd.c and cmdresp.c.

Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

libertas: clean up direct command handling

Move direct command handling through __lbs_cmd() over to using the
header as the first member of the command structure, and only define
the __lbs_cmd() callback in one place rather than 3.  Convert boot2
version command to new usage.

Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

libertas: don't run thread while firmware not yet ready

Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

libertas: switch to a waitqueue and timer for handling USB firmware load

No need to busy-wait, even if we did have a 100ms delay in the loop.
This makes it easier to support the new 'firmware ready' event which is
in the new firmware, too.

Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

libertas: improve reliability of firmware reloading on USB

Increase the delay between issuing the RESET command and the usb reset,
and be prepared to discard more than one 'normal' packet from it before
it resets.

Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

libertas: make rtap and normal modes mutually exclusive, clean up open/stop

Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

libertas: clean up is_command_allowed_in_ps()

Total overkill to have an array when there's only one command in it.

Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

libertas: remove pre_open_check()

The firmware is always initialised before we register the netdevices.
It's not possible for pre_open_check() to fail.

One day we might try loading firmware in ->open(), but still it won't be
just a _check_, like this.

Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>