Antti Palosaari [Fri, 25 Jul 2014 09:17:59 +0000 (06:17 -0300)]
[media] Kconfig: fix tuners build warnings
[next:master 7472/8702] warning: (USB_MSI2500) selects
MEDIA_TUNER_MSI001 which has unmet direct dependencies
((MEDIA_ANALOG_TV_SUPPORT || ..) && ..)
[next:master 7698/8702] warning: (MEDIA_TUNER && ..) selects
MEDIA_TUNER_XC5000 which has unmet direct dependencies
((MEDIA_ANALOG_TV_SUPPORT || ..) && ..)
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Hans Verkuil [Mon, 21 Jul 2014 13:45:43 +0000 (10:45 -0300)]
[media] radio-miropcm20: add RDS support
Once upon a time the radio-miropcm20 driver had RDS support. However, after
some internal kernel changes that support was removed. Now that we have a
nice RDS API I have been working on adding back this support. It has been
tested with the si4713 RDS transmitter and it is working quite nicely.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Hans Verkuil [Mon, 21 Jul 2014 13:45:41 +0000 (10:45 -0300)]
[media] DocBook/media: document the new RDS RX controls
Document the new RDS receiver controls. This will be used by the radio-miropcm20
driver.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Hans Verkuil [Mon, 21 Jul 2014 13:45:40 +0000 (10:45 -0300)]
[media] v4l2-ctrls: add RX RDS controls
The radio-miropcm20 driver has firmware that decodes the RDS signals. So in that
case the RDS data becomes available in the form of controls.
Add support for these controls to the control framework, allowing the miro driver
to use them.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Hans Verkuil [Mon, 21 Jul 2014 13:45:39 +0000 (10:45 -0300)]
[media] si4713: add the missing RDS functionality
Not all the RDS features of the si4713 were supported. Add
the missing bits to fully support the hardware capabilities.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Cc: Eduardo Valentin <edubezval@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Hans Verkuil [Mon, 21 Jul 2014 13:45:38 +0000 (10:45 -0300)]
[media] DocBook/media: document the new RDS TX controls
Document the new RDS features that will be supported by the si4713 driver.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Cc: Eduardo Valentin <edubezval@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Hans Verkuil [Mon, 21 Jul 2014 13:45:37 +0000 (10:45 -0300)]
[media] v4l2-ctrls: add new RDS TX controls
The si4713 supports several RDS features not yet implemented in the driver.
This patch adds the missing RDS functionality to the list of RDS controls.
The ALT_FREQS control is a compound control containing an array of up
to 25 (the maximum according to the RDS standard) frequencies. To support
that the V4L2_CTRL_TYPE_U32 was added.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Cc: Eduardo Valentin <edubezval@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Hans Verkuil [Thu, 24 Jul 2014 12:19:37 +0000 (09:19 -0300)]
[media] vb2: fix vb2_poll for output streams
vb2_poll should always return POLLOUT | POLLWRNORM as long as there
are fewer buffers queued than there are buffers available. Poll for
an output stream should only wait if all buffers are queued and nobody
is dequeuing them.
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Acked-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Hans Verkuil [Wed, 23 Jul 2014 06:17:06 +0000 (03:17 -0300)]
[media] vb2: fix videobuf2-core.h comments
A lot of work was done in vb2 to regulate how drivers and the vb2 core handle
buffer ownership, but inexplicably the videobuf2-core.h comments were never
updated. Do so now. The same was true for the replacement of the -ENOBUFS
mechanism by the min_buffers_needed field.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Hans Verkuil [Mon, 21 Jul 2014 13:45:42 +0000 (10:45 -0300)]
[media] v4l2-ctrls: add support for setting string controls
Rather than always having to use a v4l2_ext_control struct to set
a control value from within a driver, switch to just setting the
new value. This is faster and it makes it possible to set more
complex types such as a string control as is added by this
patch.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Hans Verkuil [Mon, 21 Jul 2014 13:16:47 +0000 (10:16 -0300)]
[media] Docbook/media: improve data_offset/bytesused documentation
This patch explicitly documents the relationship between bytesused and data_offset.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
David Härdeman [Thu, 3 Apr 2014 23:32:31 +0000 (20:32 -0300)]
[media] rc-core: merge rc5 and streamzap decoders
Now that the protocol is part of the scancode, it is pretty easy to merge
the rc5 and streamzap decoders. An additional advantage is that the decoder
is now stricter as it waits for the trailing silence before determining that
a command is a valid rc5/streamzap command (which avoids collisions that I've
seen with e.g. Sony protocols).
Signed-off-by: David Härdeman <david@hardeman.nu>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
David Härdeman [Thu, 3 Apr 2014 23:32:26 +0000 (20:32 -0300)]
[media] rc-core: rename dev->scanmask to dev->scancode_mask
We already have dev->scancode_filter and dev->scancode_wakeup_filter
so rename dev->scanmask to dev->scancode_mask for consistency.
Signed-off-by: David Härdeman <david@hardeman.nu>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
David Härdeman [Thu, 3 Apr 2014 23:32:21 +0000 (20:32 -0300)]
[media] rc-core: remove protocol arrays
The basic API of rc-core used to be:
dev = rc_allocate_device();
dev->x = a;
dev->y = b;
dev->z = c;
rc_register_device();
which is a pretty common pattern in the kernel, after the introduction of
protocol arrays the API looks something like:
dev = rc_allocate_device();
dev->x = a;
rc_set_allowed_protocols(dev, RC_BIT_X);
dev->z = c;
rc_register_device();
There's no real need for the protocols to be an array, so change it
back to be consistent (and in preparation for the following patches).
[m.chehab@samsung.com: added missing changes at some files]
Signed-off-by: David Härdeman <david@hardeman.nu>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
David Härdeman [Thu, 3 Apr 2014 23:32:16 +0000 (20:32 -0300)]
[media] rc-core: simplify sysfs code
Simplify and cleanup the sysfs code a bit.
[m.chehab@samsung.com: rebased and fixed a CodingStyle issue]
Signed-off-by: David Härdeman <david@hardeman.nu>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
David Härdeman [Thu, 3 Apr 2014 23:32:01 +0000 (20:32 -0300)]
[media] saa7134: NEC scancode fix
This driver codes the two address bytes in reverse order when compared to the
other drivers, so make it consistent (and update the keymap, note that the
result is a prefix change from 0x6b86 -> 0x866b, and the latter is pretty
common among the NECX keymaps. While not conclusive, it's still a strong hint
that the change is correct).
Signed-off-by: David Härdeman <david@hardeman.nu>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
David Härdeman [Thu, 3 Apr 2014 23:31:30 +0000 (20:31 -0300)]
[media] rc-core: document the protocol type
Right now the protocol information is not preserved, rc-core gets handed a
scancode but has no idea which protocol it corresponds to.
This patch (which required reading through the source/keymap for all drivers,
not fun) makes the protocol information explicit which is important
documentation and makes it easier to e.g. support multiple protocols with one
decoder (think rc5 and rc-streamzap). The information isn't used yet so there
should be no functional changes.
[m.chehab@samsung.com: rebased, added cxusb and removed bad whitespacing]
Signed-off-by: David Härdeman <david@hardeman.nu>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
David Härdeman [Thu, 3 Apr 2014 23:31:51 +0000 (20:31 -0300)]
[media] dib0700: NEC scancode cleanup
the RC RX packet is defined as:
struct dib0700_rc_response {
...
u8 not_system;
u8 system;
...
u8 data;
u8 not_data;
The NEC protocol transmits in the order:
system
not_system
data
not_data
Note that the code defines the NEC extended scancode as:
scancode = be16_to_cpu(poll_reply->system16) << 8 | poll_reply->data;
i.e.
scancode = poll_reply->not_system << 16 |
poll_reply->system << 8 |
poll_reply->data;
Which, if the order *is* reversed, would mean that the scancode that
gets defined is in reality:
scancode = poll_reply->system << 16 |
poll_reply->not_system << 8 |
poll_reply->data;
Which is the same as the order used in drivers/media/rc/ir-nec-decoder.c.
This patch changes the code to match my assumption (the generated scancode
should, however, not change).
[m.chehab@samsung.com: rebased and fixed the decoding error message]
Signed-off-by: David Härdeman <david@hardeman.nu>
CC: Patrick Boettcher <pboettcher@kernellabs.com>
Tested-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
David Härdeman [Thu, 3 Apr 2014 23:31:25 +0000 (20:31 -0300)]
[media] rc-core: improve ir-kbd-i2c get_key functions
The arguments used for ir-kbd-i2c's get_key() functions are not
really suited for rc-core and the ir_raw/ir_key distinction is
just confusing.
Convert all of them to return a protocol/scancode/toggle triple instead.
Signed-off-by: David Härdeman <david@hardeman.nu>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
David Härdeman [Thu, 3 Apr 2014 23:31:20 +0000 (20:31 -0300)]
[media] bt8xx: fixup RC5 decoding
The bt8xx driver does RC5 decoding for Nebula digi hardware, but includes
some pointless limitations (both start bits must be one, the
device/address/system must be 0x00). Remove those limitations and update
the keymap to use the full RC5 scancode (fortunately the 0x00 address
means that this is perfectly backwards compatible).
Signed-off-by: David Härdeman <david@hardeman.nu>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Daeseok Youn [Wed, 2 Apr 2014 09:49:03 +0000 (06:49 -0300)]
[media] staging: lirc: remove redundant NULL check in unregister_from_lirc()
"ir" is already checked before calling unregister_from_lirc().
Signed-off-by: Daeseok Youn <daeseok.youn@gmail.com>
Reviewed-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Mauro Carvalho Chehab [Mon, 30 Jun 2014 14:56:33 +0000 (11:56 -0300)]
[media] cxusb: increase buffer length to 80 bytes
As reported by Vincent:
[ 16.332247] xc2028 0-0061: Loading firmware for type=BASE F8MHZ (3), id
0000000000000000.
[ 16.344378] cxusb: i2c wr: len=64 is too big!
64 bytes is too short for firmware load on this device. So, increase it
to 80 bytes.
Reported-by: Vincent McIntyre <vincent.mcintyre@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Mauro Carvalho Chehab [Sat, 12 Jul 2014 00:37:46 +0000 (21:37 -0300)]
[media] DocBook: Fix ISDB-T Interleaving property
The DocBook documentation is incorrect: on ISDB-T, interleaving
time is always a power of 2. Fix it and provides a table showing
the actual interleaving length for each mode.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Mauro Carvalho Chehab [Mon, 21 Jul 2014 16:28:15 +0000 (13:28 -0300)]
[media] xc4000: Fix get_frequency()
The programmed frequency on xc4000 is not the middle
frequency, but the initial frequency on the bandwidth range.
However, the DVB API works with the middle frequency.
This works fine on set_frontend, as the device calculates
the needed offset. However, at get_frequency(), the returned
value is the initial frequency. That's generally not a big
problem on most drivers, however, starting with changeset
6fe1099c7aec, the frequency drift is taken into account at
dib7000p driver.
This broke support for PCTV 340e, with uses dib7000p demod and
xc4000 tuner.
Cc: stable@vger.kernel.org
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Mauro Carvalho Chehab [Mon, 21 Jul 2014 17:21:18 +0000 (14:21 -0300)]
[media] xc5000: Fix get_frequency()
The programmed frequency on xc5000 is not the middle
frequency, but the initial frequency on the bandwidth range.
However, the DVB API works with the middle frequency.
Cc: stable@vger.kernel.org
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Mauro Carvalho Chehab [Mon, 21 Jul 2014 16:28:14 +0000 (13:28 -0300)]
[media] xc4000: add module meta-tag with the firmware names
This meta-tag is used by some distros to help them package
the firmware and generate proper initrd images.
So, add the firmware names there.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Mauro Carvalho Chehab [Mon, 21 Jul 2014 16:28:13 +0000 (13:28 -0300)]
[media] xc4000: Update firmware name
The firmware name at:
http://www.kernellabs.com/firmware/xc4000/
Is different from the one at the Kernel. Update it
try first the new name, falling back to the previous one
if the new name can't be found.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Himangi Saraogi [Tue, 15 Jul 2014 21:31:17 +0000 (18:31 -0300)]
[media] dib7000m: Remove unnecessary null test
This patch removes the null test on ch. ch is initialized at the
beginning of the function to &demod->dtv_property_cache. Since demod
is dereferenced prior to the null test, demod must be a valid pointer,
and &demod->dtv_property_cache cannot be null.
The following Coccinelle script is used for detecting the change:
@r@
expression e,f;
identifier g,y;
statement S1,S2;
@@
*e = &f->g
<+...
f->y
...+>
*if (e != NULL || ...)
S1 else S2
Signed-off-by: Himangi Saraogi <himangi774@gmail.com>
Acked-by: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Mauro Carvalho Chehab [Sat, 12 Jul 2014 00:37:48 +0000 (21:37 -0300)]
[media] mb86a20s: Fix the code that estimates the measurement interval
Instead of looking at the guard interval field, it was using
the interval length, with is wrong. Fix it.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Mauro Carvalho Chehab [Sat, 12 Jul 2014 00:37:47 +0000 (21:37 -0300)]
[media] mb86a20s: Fix Interleaving
Interleaving code was wrong at mb86a20s: instead, it was looking
at the Guard Interval. Fix it.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Mauro Carvalho Chehab [Mon, 21 Jul 2014 17:55:05 +0000 (14:55 -0300)]
[media] mb86a20s: fix ISDB-T mode handling
The driver was reporting an incorrect mode, when mode 2
is selected.
While testing it, noticed that neither mode 1 or guard
interval 1/32 is supported by this device. Document it,
and ensure that it will report _AUTO when it doesn't lock,
in order to not report a wrong detection to userspace.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Antti Palosaari [Thu, 10 Jul 2014 11:17:59 +0000 (08:17 -0300)]
[media] m88ds3103: implement BER
Implement read_ber for BER estimate.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Antti Palosaari [Thu, 10 Jul 2014 11:17:58 +0000 (08:17 -0300)]
[media] m88ds3103: fix SNR reporting on 32-bit arch
There was 32-bit calculation overflow. Use div_u64.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Fabian Frederick [Tue, 8 Jul 2014 18:16:51 +0000 (15:16 -0300)]
[media] xc4000: remove unnecessary break after goto
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Fabian Frederick [Tue, 8 Jul 2014 18:17:41 +0000 (15:17 -0300)]
[media] xc5000: remove unnecessary break after goto
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Fabian Frederick [Tue, 8 Jul 2014 17:23:01 +0000 (14:23 -0300)]
[media] dvb-frontends: remove unnecessary break after goto
Cc: Antti Palosaari <crope@iki.fi>
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Fabian Frederick [Tue, 8 Jul 2014 17:25:17 +0000 (14:25 -0300)]
[media] xc2028: remove unnecessary break after goto
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Fabian Frederick [Tue, 8 Jul 2014 17:20:37 +0000 (14:20 -0300)]
[media] r820t: remove unnecessary break after goto
Cc: Antti Palosaari <crope@iki.fi>
Cc: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Emil Goode [Tue, 24 Jun 2014 21:42:28 +0000 (18:42 -0300)]
[media] Cleanup line > 80 character violations
This cleans up some line over 80 character violations.
Signed-off-by: Emil Goode <emilgoode@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Emil Goode [Tue, 24 Jun 2014 21:42:27 +0000 (18:42 -0300)]
[media] Remove checks of struct member addresses
This removes checks of struct member addresses since they likely result
in the condition always being true. Also in the stb6100_get_bandwidth
and tda8261_get_bandwidth functions the pointers frontend_ops and
tuner_ops are assigned the same addresses twice.
Signed-off-by: Emil Goode <emilgoode@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Heinrich Schuchardt [Thu, 19 Jun 2014 14:49:40 +0000 (11:49 -0300)]
[media] media: dib9000: avoid out of bound access
This updated patch also fixes out of bound access to b[].
In dib9000_risc_apb_access_write() an out of bound access to mb[].
The current test to avoid out of bound access to mb[] is insufficient.
For len = 19 non-existent mb[10] will be accessed.
For odd values of len b[] is accessed out of bounds.
For large values of len an of bound access to mb[] may occur in
dib9000_mbx_send_attr.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Dan Carpenter [Thu, 6 Feb 2014 07:49:47 +0000 (04:49 -0300)]
[media] dvb-frontends: decimal vs hex typo in ChannelConfiguration()
>From the context this should be hex 0x80 instead of decimal 80.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Mauro Carvalho Chehab [Tue, 22 Jul 2014 19:25:33 +0000 (16:25 -0300)]
[media] si2168: Fix a badly solved merge conflict
changeset
a733291d6934 didn't merge the fixes well. It ended by
restoring some bad logic removed there.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Acked-by: Antti Palosaari <crope@iki.fi>
Reviewed-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Mauro Carvalho Chehab [Tue, 22 Jul 2014 17:22:01 +0000 (14:22 -0300)]
[media] tuners/Kconfig: fix build when just DTV or SDR is enabled
As reported by Kbuildtest:
warning: (VIDEO_PVRUSB2 && VIDEO_TLG2300 && VIDEO_USBVISION && VIDEO_GO7007 && VIDEO_AU0828_V4L2 && VIDEO_CX231XX && VIDEO_TM6000 && VIDEO_EM28XX && VIDEO_IVTV && VIDEO_MXB && VIDEO_CX18 && VIDEO_CX23885 && VIDEO_CX88 && VIDEO_BT848 && VIDEO_SAA7134 && VIDEO_SAA7164) selects VIDEO_TUNER which has unmet direct dependencies (MEDIA_SUPPORT && MEDIA_TUNER)
That happens when:
# CONFIG_MEDIA_ANALOG_TV_SUPPORT is not set
CONFIG_MEDIA_DIGITAL_TV_SUPPORT=y
# CONFIG_MEDIA_RADIO_SUPPORT is not set
# CONFIG_MEDIA_SDR_SUPPORT is not set
CONFIG_VIDEO_AU0828_V4L2=y
CONFIG_VIDEO_CX231XX=y
CONFIG_VIDEO_TM6000=y
CONFIG_VIDEO_EM28XX=y
CONFIG_VIDEO_TUNER=y
CONFIG_MEDIA_SUPPORT=y
With means that we need to enable MEDIA_TUNER also when DTV
is enabled. While the above config doesn't cover, if we enable
SDR, the same error can also happen.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Hans Verkuil [Tue, 22 Jul 2014 04:21:37 +0000 (06:21 +0200)]
[media] go7007: move out of staging into drivers/media/usb.
Now that the custom motion detection API in this driver has been
replaced with a standard API there is no reason anymore to keep it
in staging. So (finally!) move it to drivers/media/usb.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Hans Verkuil [Tue, 22 Jul 2014 04:13:07 +0000 (06:13 +0200)]
[media] solo6x10: move out of staging into drivers/media/pci.
Now that the custom motion detection API has been replaced with a
standard API there is no reason anymore to keep it in staging.
So (finally!) move it to drivers/media/pci.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Philipp Zabel [Fri, 11 Jul 2014 09:36:43 +0000 (06:36 -0300)]
[media] coda: store IRAM size in struct coda_devtype
Similarly to workbuf_size and tempbuf_size, store iram_size in the
coda_devtype structure. This also decreases the IRAM used on i.MX6DL
to 128 KiB.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Philipp Zabel [Fri, 11 Jul 2014 09:36:42 +0000 (06:36 -0300)]
[media] coda: store global temporary buffer size in struct coda_devtype
Similarly to the work buffer size, store the temporary buffer size in the
coda_devtype structure.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Philipp Zabel [Fri, 11 Jul 2014 09:36:41 +0000 (06:36 -0300)]
[media] coda: store per-context work buffer size in struct coda_devtype
We had the workbuf_size field since the beginning.
Use it to tighten the code a little bit.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Philipp Zabel [Fri, 11 Jul 2014 09:36:40 +0000 (06:36 -0300)]
[media] coda: export auxiliary buffers via debugfs
This patch exports all auxiliary buffers, including SRAM, as debugfs binary
blobs for debugging purposes. It shows, for example, that psbuf currently
doesn't seem to be used at all on CODA7541, and that slicebuf and workbuf
usage is far from the maximum. It can also be used to validate SRAM size
allocation.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Philipp Zabel [Fri, 11 Jul 2014 09:36:39 +0000 (06:36 -0300)]
[media] coda: increase frame stride to 16 for h.264
When encoding into h.264, the input frame stride needs to be a multiple of 16.
During allocation of the input buffers, it may not be known yet whether the
encoder should create h.264 or not. Assume the worst and always use a frame
stride that is a multiple of 16.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Philipp Zabel [Fri, 11 Jul 2014 09:36:38 +0000 (06:36 -0300)]
[media] coda: round up internal frames to multiples of macroblock size for h.264
CODA7541 only supports encoding h.264 frames with width and height that are
multiples of the macroblock size.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Philipp Zabel [Fri, 11 Jul 2014 09:36:37 +0000 (06:36 -0300)]
[media] coda: allow odd width, but still round up bytesperline
Even though the CODA h.264 decoder always decodes complete macroblocks, we can
set the stride to the corresponding multiple of 16 and use a value smaller than
that as real width. Unfortunately the same doesn't work for height, as there
is no vertical linesperframe stride for discontiguous planar YUV frames.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Philipp Zabel [Fri, 11 Jul 2014 09:36:36 +0000 (06:36 -0300)]
[media] coda: add bytesperline to queue data
bytesperline is calculated in multiple places, store it in the coda_q_data
structure. This will be more useful later when adding JPEG support.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Philipp Zabel [Fri, 11 Jul 2014 09:36:35 +0000 (06:36 -0300)]
[media] coda: add reset control support
On i.MX53 and i.MX6, the CODA VPU can be reset by the System Reset Controller.
We can use this to get out of dire situations, for example after a picture
run timeout.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Philipp Zabel [Fri, 11 Jul 2014 09:36:34 +0000 (06:36 -0300)]
[media] coda: rename prescan_failed to hold and stop stream after timeout
Rename the per-context prescan_failed variable to hold, as this is what the
flag does: it temporarily keeps the coda from running until new data is fed
into the bitstream buffer or stop_streaming is called on the input side.
A prescan failure on i.MX5 is one possible reason to enter this state, another
one is a picture run timeout on i.MX6.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Philipp Zabel [Fri, 11 Jul 2014 09:36:33 +0000 (06:36 -0300)]
[media] coda: add sequence counter offset
The coda h.264 decoder also counts PIC_RUNs where no frame was decoded but
a frame was rotated out / marked as ready to be displayed. This causes an
offset between the incoming encoded frame's sequence number and the decode
sequence number returned by the coda. This patch introduces a sequence
counter offset variable to keep track of the difference.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Philipp Zabel [Fri, 11 Jul 2014 09:36:32 +0000 (06:36 -0300)]
[media] coda: alert userspace about macroblock errors
If the CODA reports macroblock errors, also set the VB2_BUF_STATE_ERROR flag
to alert userspace.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Philipp Zabel [Fri, 11 Jul 2014 09:36:31 +0000 (06:36 -0300)]
[media] coda: add decoder timestamp queue
The coda driver advertises timestamp_type V4L2_BUF_FLAG_TIMESTAMP_COPY on
both queues, so we have to copy timestamps from input v4l2 buffers to the
corresponding destination v4l2 buffers. Since the h.264 decoder can reorder
frames, a timestamp queue is needed to keep track of and assign the correct
timestamp to destination buffers.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Michael Olbrich [Fri, 11 Jul 2014 09:36:30 +0000 (06:36 -0300)]
[media] coda: try to schedule a decode run after a stop command
In case no further buffers are queued after the stop command, restart
job scheduling explicitly.
Signed-off-by: Michael Olbrich <m.olbrich@pengutronix.de>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Michael Olbrich [Tue, 22 Jul 2014 12:36:04 +0000 (09:36 -0300)]
[media] v4l2-mem2mem: export v4l2_m2m_try_schedule
Some drivers might allow to decode remaining frames from an internal ringbuffer
after a decoder stop command. Allow those to call v4l2_m2m_try_schedule
directly.
Signed-off-by: Michael Olbrich <m.olbrich@pengutronix.de>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Philipp Zabel [Fri, 11 Jul 2014 09:36:28 +0000 (06:36 -0300)]
[media] coda: add cyclic intra refresh control
Allow userspace to enable cyclic intra refresh by setting the number of
intra macroblocks per frame to a non-zero value.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Philipp Zabel [Fri, 11 Jul 2014 09:36:27 +0000 (06:36 -0300)]
[media] coda: add h.264 deblocking filter controls
This adds controls for the h.264 deblocking loop filter.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Philipp Zabel [Fri, 11 Jul 2014 09:36:26 +0000 (06:36 -0300)]
[media] coda: add h.264 min/max qp controls
If the bitrate control is set, the encoder works in CBR mode, dynamically
changing the quantization parameters to achieve a constant bitrate.
With the min/max QP controls the quantization parameters can be limited
to a given range.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Philipp Zabel [Fri, 11 Jul 2014 09:36:25 +0000 (06:36 -0300)]
[media] coda: select GENERIC_ALLOCATOR
The driver uses the genalloc API, which doesn't have stubs in
case GENERIC_ALLOCATOR is disabled.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Philipp Zabel [Fri, 11 Jul 2014 09:36:24 +0000 (06:36 -0300)]
[media] coda: split firmware version check out of coda_hw_init
This adds a new function coda_check_firmware that does the firmware
version checks so that this can be done only once from coda_probe
instead of every time the runtime pm framework resumes the coda.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Philipp Zabel [Fri, 11 Jul 2014 09:36:23 +0000 (06:36 -0300)]
[media] coda: Add runtime pm support
This patch allows to use the runtime pm and generic pm domain frameworks
to completely gate power to the VPU if it is unused. This functionality
is available on i.MX6.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Philipp Zabel [Fri, 11 Jul 2014 09:36:22 +0000 (06:36 -0300)]
[media] coda: use ctx->fh.m2m_ctx instead of ctx->m2m_ctx
v4l2_fh already contains a mem2mem context pointer. Use it.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Philipp Zabel [Fri, 11 Jul 2014 09:36:21 +0000 (06:36 -0300)]
[media] coda: Use mem-to-mem ioctl helpers
Use the mem2mem helpers introduced to get rid of some duplicated code.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Philipp Zabel [Fri, 11 Jul 2014 09:36:20 +0000 (06:36 -0300)]
[media] coda: add workqueue to serialize hardware commands
Using the coda_mutex lock to serialize hardware access would cause
"INFO: possible circular locking dependency detected" lockdep warnings.
Since the possible locking paths are hard to follow, serialize hardware
access with a single workqueue thread. Ultimately the workqueue could
be converted to only do register setup and readout for per-command work
items.
Using the initialized context property, SEQ_END is only queued in
coda_release when needed.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Philipp Zabel [Fri, 11 Jul 2014 09:36:19 +0000 (06:36 -0300)]
[media] coda: add selection API support for h.264 decoder
The h.264 decoder produces capture frames that are a multiple of the macroblock
size (16 pixels). To inform userspace about invalid pixel data at the edges,
use the active and padded composing rectangles on the capture queue.
The cropping information is obtained from the h.264 sequence parameter set.
Reviewed-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Philipp Zabel [Fri, 11 Jul 2014 09:36:18 +0000 (06:36 -0300)]
[media] coda: remove BUG() in get_q_data
This allows us to get rid of the now superfluous v4l2_m2m_get_vq check
in G_FMT. Also, we can use this to check the buffer type in G_SELECTION
later.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Philipp Zabel [Fri, 11 Jul 2014 09:36:17 +0000 (06:36 -0300)]
[media] coda: Add encoder/decoder support for CODA960
This patch adds support for the CODA960 VPU in Freescale i.MX6 SoCs.
It enables h.264 and MPEG4 encoding and decoding support. Besides the usual
register shifting, the CODA960 gains frame memory control and GDI registers
that are set up for linear mapping right now, needs ENC_PIC_SRC_INDEX to be
set beyond the number of internal buffers for some reason, and has subsampling
buffers that need to be set up. Also, the work buffer size is increased to
80 KiB.
The CODA960 firmware spins if there is not enough input data in the bitstream
buffer. To make it continue, buffers need to be copied into the bitstream as
soon as they are queued. As the bitstream fifo is written into from two places,
it must be protected with a mutex. For that, using a threaded interrupt handler
is necessary.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Antti Palosaari [Tue, 22 Jul 2014 08:43:06 +0000 (05:43 -0300)]
[media] msi2500: rename namespace msi3101 => msi2500
Rename driver namespace according to current driver name. Old
msi3101 was name of reference design, msi2500 is name of chip
itself.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Antti Palosaari [Tue, 22 Jul 2014 08:29:57 +0000 (05:29 -0300)]
[media] msi2500: refactor USB stream copying
There was a lot of duplicated functionality between different
stream format handling. Refactor functionality in order to get
rid of duplicated code.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Antti Palosaari [Tue, 22 Jul 2014 05:44:12 +0000 (02:44 -0300)]
[media] msi2500: correct style issues
Correct some style issues, mostly reported by checkpatch.pl.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Arun Kumar K [Wed, 21 May 2014 09:29:31 +0000 (06:29 -0300)]
[media] s5p-mfc: Add init buffer cmd to MFCV6
Latest MFC v6 firmware requires tile mode and loop filter
setting to be done as part of Init buffer command, in sync
with v7. This patch adds this support for new v6 firmware.
Signed-off-by: Arun Kumar K <arun.kk@samsung.com>
Signed-off-by: Kiran AVND <avnd.kiran@samsung.com>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Arun Kumar K [Wed, 21 May 2014 09:29:30 +0000 (06:29 -0300)]
[media] s5p-mfc: Support multiple firmware sub-versions
For MFC firmwares, improved versions with bug fixes and
feature additions are released keeping the firmware version
including major and minor number same. The issue came with
the release of a new MFCv6 firmware with an interface change.
This patch adds the support of accepting multiple firmware
binaries for every version with the driver trying to load
firmwares starting from latest. This ensures full backward
compatibility regardless of which firmware version and kernel
version is used.
Signed-off-by: Arun Kumar K <arun.kk@samsung.com>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Arun Kumar K [Wed, 21 May 2014 09:29:29 +0000 (06:29 -0300)]
[media] s5p-mfc: Remove duplicate function s5p_mfc_reload_firmware
The function s5p_mfc_reload_firmware is exactly same as
s5p_mfc_load_firmware. So removing the duplicate function.
Signed-off-by: Arun Kumar K <arun.kk@samsung.com>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Laurent Pinchart [Mon, 26 May 2014 19:31:28 +0000 (16:31 -0300)]
[media] tvp5150: Use i2c_smbus_(read|write)_byte_data
X-Patchwork-Delegate: mchehab@redhat.com
Replace the custom I2C read/write implementation with SMBUS functions to
simplify the driver.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Laurent Pinchart [Mon, 26 May 2014 19:28:31 +0000 (16:28 -0300)]
[media] tvp5150: Fix device ID kernel log message
X-Patchwork-Delegate: mchehab@redhat.com
The driver mistakenly prints the ROM version instead of the device ID to
the kernel log when detecting the chip. Fix it.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Paul Bolle [Wed, 16 Apr 2014 15:47:43 +0000 (12:47 -0300)]
[media] sms: Remove CONFIG_ prefix from Kconfig symbols
X-Patchwork-Delegate: mchehab@redhat.com
Remove the CONFIG_ prefix from two Kconfig symbols in a dependency for
SMS_SIANO_DEBUGFS. This prefix is invalid inside Kconfig files.
Note that the current (common sense) dependency on SMS_USB_DRV and
SMS_SDIO_DRV being equal ensures that SMS_SIANO_DEBUGFS will not
violate its constraints. These constraint are that:
- it should only be built if SMS_USB_DRV is set;
- it can't be builtin if USB support is modular.
So drop the dependency on SMS_USB_DRV, as it is unneeded.
Fixes:
6c84b214284e ("[media] sms: fix randconfig building error")
Reported-by: Martin Walch <walch.martin@web.de>
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
CrazyCat [Tue, 3 Jun 2014 17:22:44 +0000 (14:22 -0300)]
[media] dw2102: Geniatech T220 init fixed
Geniatech T220 init fixed - reset cmd from windows driver and fixed TS bus config for cxd2820r.
Signed-off-by: Evgeny Plehov <EvgenyPlehov@ukr.net>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
CrazyCat [Tue, 3 Jun 2014 17:19:07 +0000 (14:19 -0300)]
[media] cxd2820r: TS clock inversion in config
TS clock inversion in config.
Signed-off-by: Evgeny Plehov <EvgenyPlehov@ukr.net>
Reviewed-by: Antti Palosaari <crope@iki.fi>
Acked-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Mauro Carvalho Chehab [Tue, 22 Jul 2014 05:03:59 +0000 (02:03 -0300)]
Merge commit '
67dd8f35c2d8ed80f26c9654b474cffc11c6674d' into patchwork
* .: (268 commits)
Linux 3.16-rc6
um: segv: Save regs only in case of a kernel mode fault
um: Fix hung task in fix_range_common()
um: Ensure that a stub page cannot get unmapped
Revert "um: Fix wait_stub_done() error handling"
btrfs: test for valid bdev before kobj removal in btrfs_rm_device
Btrfs: fix abnormal long waiting in fsync
random: check for increase of entropy_count because of signed conversion
ARM: EXYNOS: Fix core ID used by platsmp and hotplug code
ahci: add support for the Promise FastTrak TX8660 SATA HBA (ahci mode)
ARM: at91/dt: add missing clocks property to pwm node in sam9x5.dtsi
ARM: at91/dt: fix usb0 clocks definition in sam9n12 dtsi
ARM: at91: at91sam9x5: correct typo error for ohci clock
irqchip: gic: Fix core ID calculation when topology is read from DT
GFS2: fs/gfs2/rgrp.c: kernel-doc warning fixes
GFS2: memcontrol: Spelling s/invlidate/invalidate/
GFS2: Allow caching of glocks for flock
GFS2: Allow flocks to use normal glock dq rather than dq_wait
GFS2: replace count*size kzalloc by kcalloc
GFS2: Use GFP_NOFS when allocating glocks
...
Conflicts:
drivers/media/dvb-frontends/si2168.c
drivers/media/dvb-frontends/si2168_priv.h
drivers/media/tuners/si2157.c
Mauro Carvalho Chehab [Tue, 22 Jul 2014 04:40:00 +0000 (01:40 -0300)]
[media] v4l2-subdev: Fix compilation when !VIDEO_V4L2_SUBDEV_API
As reported by Kbuildtest:
drivers/media/v4l2-core/v4l2-subdev.c: In function 'check_format':
drivers/media/v4l2-core/v4l2-subdev.c:136:23: error: 'struct v4l2_subdev' has no member named 'entity'
if (format->pad >= sd->entity.num_pads)
^
drivers/media/v4l2-core/v4l2-subdev.c: In function 'check_crop':
drivers/media/v4l2-core/v4l2-subdev.c:148:21: error: 'struct v4l2_subdev' has no member named 'entity'
if (crop->pad >= sd->entity.num_pads)
^
drivers/media/v4l2-core/v4l2-subdev.c: In function 'check_selection':
drivers/media/v4l2-core/v4l2-subdev.c:161:20: error: 'struct v4l2_subdev' has no member named 'entity'
if (sel->pad >= sd->entity.num_pads)
^
drivers/media/v4l2-core/v4l2-subdev.c: In function 'check_edid':
drivers/media/v4l2-core/v4l2-subdev.c:169:21: error: 'struct v4l2_subdev' has no member named 'entity'
if (edid->pad >= sd->entity.num_pads)
^
drivers/media/v4l2-core/v4l2-subdev.c: In function 'subdev_do_ioctl':
>> drivers/media/v4l2-core/v4l2-subdev.c:186:6: warning: unused variable 'rval' [-Wunused-variable]
int rval;
^
drivers/media/v4l2-core/v4l2-subdev.c: At top level:
drivers/media/v4l2-core/v4l2-subdev.c:129:12: warning: 'check_format' defined but not used [-Wunused-function]
static int check_format(struct v4l2_subdev *sd,
^
drivers/media/v4l2-core/v4l2-subdev.c:142:12: warning: 'check_crop' defined but not used [-Wunused-function]
static int check_crop(struct v4l2_subdev *sd, struct v4l2_subdev_crop *crop)
^
drivers/media/v4l2-core/v4l2-subdev.c:154:12: warning: 'check_selection' defined but not used [-Wunused-function]
static int check_selection(struct v4l2_subdev *sd,
^
drivers/media/v4l2-core/v4l2-subdev.c:167:12: warning: 'check_edid' defined but not used [-Wunused-function]
static int check_edid(struct v4l2_subdev *sd, struct v4l2_subdev_edid *edid)
The above warnins happen because those functions are used only
when the V4L2 subdev API is enabled.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Antti Palosaari [Tue, 22 Jul 2014 04:28:00 +0000 (01:28 -0300)]
[media] rtl2832_sdr: fix Kconfig dependencies
MEDIA_SDR_SUPPORT and I2C_MUX are needed for rtl2832_sdr.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Antti Palosaari [Tue, 22 Jul 2014 03:18:19 +0000 (00:18 -0300)]
[media] rtl2832_sdr: remove plain 64-bit divisions
Commit
0ba2aeb6dab80920edd9cf5b93b1ea4d6913b8f3
(v4l2-ctrls: increase internal min/max/step/def to 64 bit)
changes v4l2 controls to 64-bit. Driver it not working on 32-bit
arch as it uses directly control 'step' which is changed to 64-bit.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Cc: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Peter Meerwald [Fri, 4 Jul 2014 07:51:47 +0000 (04:51 -0300)]
[media] media:platform: OMAP3 camera support needs VIDEOBUF2_DMA_CONTIG
drivers/built-in.o: In function `isp_video_open':
/src/linux/drivers/media/platform/omap3isp/ispvideo.c:1253: undefined reference to `vb2_dma_contig_memops'
drivers/built-in.o: In function `omap3isp_video_init':
/src/linux/drivers/media/platform/omap3isp/ispvideo.c:1344: undefined reference to `vb2_dma_contig_init_ctx'
/src/linux/drivers/media/platform/omap3isp/ispvideo.c:1350: undefined reference to `vb2_dma_contig_cleanup_ctx'
drivers/built-in.o: In function `omap3isp_video_cleanup':
/src/linux/drivers/media/platform/omap3isp/ispvideo.c:1381: undefined reference to `vb2_dma_contig_cleanup_ctx'
make: *** [vmlinux] Error 1
Signed-off-by: Peter Meerwald <pmeerw@pmeerw.net>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Salva Peiró [Sat, 7 Jun 2014 14:41:44 +0000 (11:41 -0300)]
[media] media-device: Remove duplicated memset() in media_enum_entities()
After the zeroing the whole struct struct media_entity_desc u_ent,
it is no longer necessary to memset(0) its u_ent.name field.
CC: stable@vger.kernel.org
Signed-off-by: Salva Peiró <speiro@ai2.upv.es>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Sakari Ailus [Wed, 4 Jun 2014 11:22:03 +0000 (08:22 -0300)]
[media] v4l: subdev: Unify argument validation across IOCTLs
Separate validation of different argument types. There's no reason to do
this separately for every IOCTL.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Laurent Pinchart [Mon, 19 May 2014 15:04:32 +0000 (12:04 -0300)]
[media] v4l: s3c-camif: Return V4L2_FIELD_NONE from pad-level set format
The bridge driver doesn't support interlaced formats, always return the
field order set to V4L2_FIELD_NONE.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Laurent Pinchart [Mon, 19 May 2014 15:04:32 +0000 (12:04 -0300)]
[media] v4l: smiapp: Return V4L2_FIELD_NONE from pad-level get/set format
The SMIA++ sensors are progressive, always return the field order set to
V4L2_FIELD_NONE.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Laurent Pinchart [Mon, 19 May 2014 15:04:32 +0000 (12:04 -0300)]
[media] v4l: s5k6a3: Return V4L2_FIELD_NONE from pad-level set format
The sensor is progressive, always return the field order set to
V4L2_FIELD_NONE.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Laurent Pinchart [Mon, 19 May 2014 15:04:32 +0000 (12:04 -0300)]
[media] v4l: s5k5baf: Return V4L2_FIELD_NONE from pad-level set format
The sensor is progressive, always return the field order set to
V4L2_FIELD_NONE.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Laurent Pinchart [Mon, 19 May 2014 15:04:32 +0000 (12:04 -0300)]
[media] v4l: s5k4ecgx: Return V4L2_FIELD_NONE from pad-level set format
The sensor is progressive, always return the field order set to
V4L2_FIELD_NONE.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Laurent Pinchart [Mon, 19 May 2014 15:04:32 +0000 (12:04 -0300)]
[media] v4l: noon010p30: Return V4L2_FIELD_NONE from pad-level set format
The sensor is progressive, always return the field order set to
V4L2_FIELD_NONE.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Dan Carpenter [Mon, 9 Jun 2014 15:10:46 +0000 (12:10 -0300)]
[media] davinci: vpfe: dm365: remove duplicate RSZ_LPF_INT_MASK
The RSZ_LPF_INT_MASK define is cut and pasted twice so we can remove the
second instance.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Lad, Prabhakar [Tue, 29 Apr 2014 06:49:34 +0000 (03:49 -0300)]
[media] media: davinci_vpfe: dm365_resizer: fix sparse warning
this patch fixes following sparse warning,
dm365_resizer.c:223:1: warning: symbol 'resizer_calculate_resize_ratios' was not declared. Should it be static?
dm365_resizer.c:313:5: warning: symbol 'resizer_configure_output_win' was not declared. Should it be static?
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Lad, Prabhakar [Sat, 29 Mar 2014 04:56:13 +0000 (01:56 -0300)]
[media] staging: media: davinci_vpfe: fix checkpatch warning
This patch fixes following checkpatch warning,
media/davinci_vpfe/dm365_ipipe.c:1271: WARNING: Missing a blank line after declarations
media/davinci_vpfe/dm365_ipipe.c:1313: WARNING: Missing a blank line after declarations
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>