Lothar Waßmann [Wed, 15 Dec 2010 21:20:13 +0000 (22:20 +0100)]
ARM: mxs: add a dma mask to fec devices
This is not strictly necessary but the right thing to do.
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Uwe Kleine-König [Fri, 18 Feb 2011 20:59:25 +0000 (21:59 +0100)]
ARM: mxc: free dma_mask in error path
This fixes a small memory leak that was only hit in very unlikely error
paths
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Lothar Waßmann [Wed, 15 Dec 2010 21:11:31 +0000 (22:11 +0100)]
ARM: mxs: free dma_mask in error path
This fixes a small memory leak that was only hit in very unlikely error
paths.
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Eric Bénard [Fri, 25 Feb 2011 13:38:29 +0000 (14:38 +0100)]
cpuimx51sd: mcp2515 supports up to 10MHz SPI clock
Signed-off-by: Eric Bénard <eric@eukrea.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Eric Bénard [Fri, 25 Feb 2011 14:04:14 +0000 (15:04 +0100)]
cpuimx51sd: fix tsc2007
- wrong MUX was set before for IRQ
- get_pendown_state is no more needed
Signed-off-by: Eric Bénard <eric@eukrea.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Eric Bénard [Fri, 25 Feb 2011 13:38:27 +0000 (14:38 +0100)]
cpuimx51sd: add cpufreq support
Signed-off-by: Eric Bénard <eric@eukrea.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Eric Bénard [Fri, 25 Feb 2011 12:48:15 +0000 (13:48 +0100)]
eukrea-tlv320: add MBIMXSD51 support
Signed-off-by: Eric Bénard <eric@eukrea.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Wolfram Sang [Wed, 23 Feb 2011 13:51:58 +0000 (14:51 +0100)]
arm: mach-mx3: use IMX_GPIO_NR instead of hard-coded values
The latter are error-prone because the bank number is one less than one
would read in the documentation.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Acked-by: Eric Benard <eric@eukrea.com>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Denis 'GNUtoo' Carikli [Fri, 18 Feb 2011 21:22:23 +0000 (22:22 +0100)]
mx31: add support for the bugbase 1.3 from buglabs
Note that the hardware schematics and documentations can be obtained
here: http://www.bugcommunity.com/wiki/index.php/BUGbase
Signed-off-by: Denis 'GNUtoo' Carikli <GNUtoo@no-log.org>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Shawn Guo [Wed, 23 Feb 2011 08:06:55 +0000 (16:06 +0800)]
ARM: mx51_defconfig: change CONFIG_LEDS_CLASS 'm' to 'y'
This patch is to fix the warning below.
arch/arm/configs/mx51_defconfig:113:warning: symbol value 'm' invalid for LEDS_CLASS
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Fabio Estevam [Tue, 22 Feb 2011 23:24:13 +0000 (20:24 -0300)]
ARM: imx/mach-mx25_3ds: Use IMX_GPIO_NR instead of hard-coded values
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Richard Zhu [Tue, 22 Feb 2011 10:13:22 +0000 (18:13 +0800)]
ARM: imx53: add sdhc pad settings
Signed-off-by: Richard Zhao <richard.zhao@freescale.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Richard Zhao [Fri, 18 Feb 2011 12:26:30 +0000 (20:26 +0800)]
ARM: imx53: correct Silicon Revision definition following fuse map
Signed-off-by: Richard Zhao <richard.zhao@freescale.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Frank Li [Mon, 21 Feb 2011 06:28:10 +0000 (14:28 +0800)]
ARM: imx53_smd add uncompress print
Signed-off-by: Frank Li <Frank.Li@freescale.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Richard Zhao [Fri, 18 Feb 2011 04:36:17 +0000 (12:36 +0800)]
ARM: imx50: correct iomux-mx50.h wrong daisy chain settings
Most fix is for uart txd/cts. They don't need to select input.
And fix some other pads with wrong select input.
Signed-off-by: Richard Zhao <richard.zhao@freescale.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Richard Zhao [Fri, 18 Feb 2011 04:36:16 +0000 (12:36 +0800)]
ARM: imx53_loco: add i2c device support
Signed-off-by: Richard Zhao <richard.zhao@freescale.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Richard Zhao [Fri, 18 Feb 2011 04:36:15 +0000 (12:36 +0800)]
ARM: imx53_loco add uncompress print
Signed-off-by: Richard Zhao <richard.zhao@freescale.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Richard Zhao [Fri, 18 Feb 2011 04:36:14 +0000 (12:36 +0800)]
ARM: imx53_loco: add all pad configure.
Signed-off-by: Richard Zhao <richard.zhao@freescale.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Fabio Estevam [Thu, 17 Feb 2011 20:09:53 +0000 (18:09 -0200)]
ARM: mach-mx5: Add watchdog support for MX53 based boards
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Fabio Estevam [Thu, 17 Feb 2011 20:09:52 +0000 (18:09 -0200)]
ARM: mx5: Add watchdog support for MX53
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Arnaud Patard (Rtp) [Thu, 17 Feb 2011 14:31:32 +0000 (15:31 +0100)]
mx51: add support for efika smartbook
Signed-off-by: Arnaud Patard <arnaud.patard@rtp-net.org>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Arnaud Patard (Rtp) [Thu, 17 Feb 2011 14:31:31 +0000 (15:31 +0100)]
efika: enable cpufreq
Enable cpufreq on Genesi efika platforms
Signed-off-by: Arnaud Patard <arnaud.patard@rtp-net.org>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Arnaud Patard (Rtp) [Thu, 17 Feb 2011 14:31:30 +0000 (15:31 +0100)]
efikamx: add mc13892 support / implement power off
This patch declares regulators for the efikamx. Use it also to power off the
efikamx.
Unfortunately, on the efikamx to2 boards, this doesn't work but they allow to
power off by setting GPIO 4 13 to high level instead of powering off through
the mc13892.
Signed-off-by: Arnaud Patard <arnaud.patard@rtp-net.org>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Arnaud Patard (Rtp) [Thu, 17 Feb 2011 14:31:29 +0000 (15:31 +0100)]
efikamx: add usb h1 support
Now that usb has been fixed, we can enable usb h1 on efikamx
Signed-off-by: Arnaud Patard <arnaud.patard@rtp-net.org>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Arnaud Patard (Rtp) [Thu, 17 Feb 2011 14:31:28 +0000 (15:31 +0100)]
Introduce EFIKA_COMMON
The Genesi EFIKA MX and EFIKA Smartbook are sharing a lot of things
so it makes sense to create a common file for both devices and a specific
file for each. No functionnal change except dropping uart 1 & 2.
Signed-off-by: Arnaud Patard <arnaud.patard@rtp-net.org>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Shawn Guo [Thu, 17 Feb 2011 06:28:52 +0000 (14:28 +0800)]
ARM: mxs/mx28evk: add auart devices
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Shawn Guo [Thu, 17 Feb 2011 06:28:51 +0000 (14:28 +0800)]
ARM: mxs/mx23evk: add auart device
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Shawn Guo [Thu, 17 Feb 2011 06:28:50 +0000 (14:28 +0800)]
ARM: mx23: dynamically allocate mx23 auart device
i.MX23 Reference Manaul starts auart index from 1 than 0. Changing
the index to start from 0 requires corresponding changes on base
address, irq, and iomux definitions, and will probably confuse people
who reads codes and hardware documents together.
This patch introduced the field 'hwid' to distinguish the driver id
and controller id. These two ids are different on mx23 while
identical on mx28.
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Shawn Guo [Thu, 17 Feb 2011 06:28:49 +0000 (14:28 +0800)]
ARM: mx23: rename mx23 auart irq definition to align with mx28
i.MX23 Reference Manual names auart irq differently from i.MX28.
This patch is to align the naming with mx28, so that some device
registration codes can be shared.
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Jesper Juhl [Mon, 14 Feb 2011 22:54:00 +0000 (23:54 +0100)]
Freescale STMP37XX/STMP378X Application UART driver: remove duplicate linux/device.h include
Do not include linux/device.h twice in drivers/tty/serial/mxs-auart.c .
Once is enough.
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Julien Boibessot [Fri, 11 Feb 2011 14:15:30 +0000 (15:15 +0100)]
i.MX51 iomux: Fixes MX51_PAD_UART2_TXD__UART2_TXD & MX51_PAD_USBH1_DATA2__UART2_TXD declarations
Fixes 2 small regressions of recent iomux changes:
- current MX51_PAD_UART2_TXD__UART2_TXD declaration overwrites
IOMUXC_UART2_IPP_UART_RXD_MUX_SELECT_INPUT register (0x09ec) and prevent
UART2 Rx from working properly.
(Tested on my custom i.MX51 board where UART2 is used as console)
- current MX51_PAD_USBH1_DATA2__UART2_TXD declaration also has the same problem.
(Not tested)
Signed-off-by: Julien Boibessot <julien.boibessot@armadeus.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Uwe Kleine-König [Fri, 11 Feb 2011 09:21:09 +0000 (10:21 +0100)]
ARM: mx3/mx31ads: fix comments of irq callbacks
The arguments to these callbacks were changed in
e981a30 (ARM: mx3: irq_data conversion.)
but the comments were not adapted.
Cc: Lennert Buytenhek <buytenh@secretlab.ca>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Uwe Kleine-König [Fri, 11 Feb 2011 09:21:08 +0000 (10:21 +0100)]
ARM: mx3: remove some useless comments
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Uwe Kleine-König [Fri, 11 Feb 2011 09:23:19 +0000 (10:23 +0100)]
ARM: mx3+mx5: rename mxc_board_init to ${machine}_init
mxc_board_init is too generic to be useful. Additionally change some
mxc_timer to ${machine}_timer, too.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Sascha Hauer [Mon, 3 Jan 2011 10:30:28 +0000 (11:30 +0100)]
ARM i.MX ehci: do ehci init in board specific functions
The mxc-ehci driver calls SoC specific phy initialization right after
calling board specific initialization. To offer greater flexibility for
boards to setup the phy and to get rid of some unnecessary flags in
platform data this patch lets the boards call the SoC specific phy
initialization and remove it from the driver.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Sascha Hauer [Mon, 3 Jan 2011 09:33:01 +0000 (10:33 +0100)]
ARM i.MX ehci: factor out soc specific functions
Currently we have a mxc_initialize_usb_hw which is called on every
i.MX SoC. This function dispatches the different SoC types, which
is quite ugly. This patch moves the SoC specific USB initialization
to their correspondive mach directories.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Sascha Hauer [Fri, 11 Feb 2011 07:32:18 +0000 (08:32 +0100)]
Merge commit 'v2.6.38-rc4' into imx-for-2.6.39
Conflicts:
arch/arm/mach-mxs/clock-mx28.c
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Uwe Kleine-König [Mon, 7 Feb 2011 15:35:22 +0000 (16:35 +0100)]
ARM: mxc91231: use .init_early to initialize cpu type
This used to be done in .map_io which is supposed to only setup the memory
mapping.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Uwe Kleine-König [Mon, 7 Feb 2011 15:35:21 +0000 (16:35 +0100)]
ARM: mx5: use .init_early to initialize cpu type, reset address and iomuxer
This used to be done in .map_io which is supposed to only setup the
memory mapping.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Uwe Kleine-König [Mon, 7 Feb 2011 15:35:20 +0000 (16:35 +0100)]
ARM: mx3: use .init_early to initialize cpu type, reset address and iomuxer
This used to be done in .map_io which is supposed to only setup the
memory mapping.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Uwe Kleine-König [Mon, 7 Feb 2011 15:35:19 +0000 (16:35 +0100)]
ARM: imx: use .init_early to initialize cpu type and reset address
This used to be done in .map_io which is supposed to only setup the
memory mapping.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
David Jander [Thu, 10 Feb 2011 09:59:44 +0000 (10:59 +0100)]
ARM: imx+mx3: convert to mc13xxx MFD
Signed-off-by: David Jander <david@protonic.nl>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Uwe Kleine-König [Thu, 10 Feb 2011 09:56:21 +0000 (10:56 +0100)]
ARM: mx3/mx31_3ds: fix compiler warning without CONFIG_USB_ULPI
This fixes:
arch/arm/mach-mx3/mach-mx31_3ds.c:249: warning: 'mx31_3ds_host2_init' defined but not used
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Uwe Kleine-König [Thu, 10 Feb 2011 10:07:27 +0000 (11:07 +0100)]
ARM: imx/eukrea_mbimx27: fix compile warnings about unused variables
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Linus Torvalds [Tue, 8 Feb 2011 00:03:17 +0000 (16:03 -0800)]
Linux 2.6.38-rc4
Linus Torvalds [Mon, 7 Feb 2011 23:20:11 +0000 (15:20 -0800)]
Merge master.kernel.org:/home/rmk/linux-2.6-arm
* master.kernel.org:/home/rmk/linux-2.6-arm:
ALSA: AACI: allow writes to MAINCR to take effect
ARM: Update mach-types
ARM: 6652/1: ep93xx: correct the end address of the AC97 memory resource
ARM: mxs/imx28: remove now unused clock lookup "fec.0"
ARM: mxs: fix clock base address missing
ARM: mxs: acknowledge gpio irq
ARM: mach-imx/mach-mx25_3ds: Fix section type
ARM: imx: Add VPR200 and MX51_3DS entries to uncompress.h
ARM i.MX23: use correct register for setting the rate
ARM i.MX23/28: remove secondary field from struct clk. It's unused
ARM i.MX28: use correct register for setting the rate
ARM i.MX28: fix bit operation
Linus Torvalds [Mon, 7 Feb 2011 22:06:18 +0000 (14:06 -0800)]
Merge git://git./linux/kernel/git/mason/btrfs-unstable
* git://git.kernel.org/pub/scm/linux/kernel/git/mason/btrfs-unstable: (33 commits)
Btrfs: Fix page count calculation
btrfs: Drop __exit attribute on btrfs_exit_compress
btrfs: cleanup error handling in btrfs_unlink_inode()
Btrfs: exclude super blocks when we read in block groups
Btrfs: make sure search_bitmap finds something in remove_from_bitmap
btrfs: fix return value check of btrfs_start_transaction()
btrfs: checking NULL or not in some functions
Btrfs: avoid uninit variable warnings in ordered-data.c
Btrfs: catch errors from btrfs_sync_log
Btrfs: make shrink_delalloc a little friendlier
Btrfs: handle no memory properly in prepare_pages
Btrfs: do error checking in btrfs_del_csums
Btrfs: use the global block reserve if we cannot reserve space
Btrfs: do not release more reserved bytes to the global_block_rsv than we need
Btrfs: fix check_path_shared so it returns the right value
btrfs: check return value of btrfs_start_ioctl_transaction() properly
btrfs: fix return value check of btrfs_join_transaction()
fs/btrfs/inode.c: Add missing IS_ERR test
btrfs: fix missing break in switch phrase
btrfs: fix several uncheck memory allocations
...
Linus Torvalds [Mon, 7 Feb 2011 22:05:38 +0000 (14:05 -0800)]
Merge branch 'merge' of git://git./linux/kernel/git/benh/powerpc
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
powerpc: Fix hcall tracepoint recursion
powerpc/numa: Fix bug in unmap_cpu_from_node
powerpc/numa: Disable VPHN on dedicated processor partitions
powerpc/numa: Add length when creating OF properties via VPHN
powerpc/numa: Check for all VPHN changes
powerpc/numa: Only use active VPHN count fields
powerpc/pseries: Remove unnecessary variable initializations in numa.c
powerpc/pseries: Fix brace placement in numa.c
powerpc/pseries: Fix typo in VPHN comments
powerpc: Fix some 6xx/7xxx CPU setup functions
powerpc: Pass the right cpu_spec to ->setup_cpu() on 64-bit
powerpc/book3e: Protect complex macro args in mmu-book3e.h
powerpc: Fix pfn_valid() when memory starts at a non-zero address
Linus Torvalds [Mon, 7 Feb 2011 22:05:24 +0000 (14:05 -0800)]
Merge branch 'omap-fixes-for-linus' of git://git./linux/kernel/git/tmlind/linux-omap-2.6
* 'omap-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6:
arm: omap4: panda: remove usb_nop_xceiv_register(v1)
OMAP1: Fix non-working LCD on OMAP310
OMAP3: Devkit8000: Change lcd power pin
omap1: remove duplicated #include
arm: mach-omap2: mux: free allocated memory on error exit
arm: mach-omap2: board-rm680: fix rm680_vemmc regulator constraints
OMAP: PM: SmartReflex: Fix possible null pointer read access
OMAP: PM: SmartReflex: Fix possible memory leak
arm: mach-omap2: voltage: debugfs: fix memory leak
OMAP3: PM: fix save secure RAM to restore MPU power state
OMAP: PM: SmartReflex: Add missing IS_ERR test
Linus Torvalds [Mon, 7 Feb 2011 22:04:43 +0000 (14:04 -0800)]
Merge branch 'x86-fixes-for-linus' of git://git./linux/kernel/git/tip/linux-2.6-tip
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86, nx: Mark the ACPI resume trampoline code as +x
Tetsuo Handa [Mon, 7 Feb 2011 13:36:16 +0000 (13:36 +0000)]
CRED: Fix memory and refcount leaks upon security_prepare_creds() failure
In prepare_kernel_cred() since 2.6.29, put_cred(new) is called without
assigning new->usage when security_prepare_creds() returned an error. As a
result, memory for new and refcount for new->{user,group_info,tgcred} are
leaked because put_cred(new) won't call __put_cred() unless old->usage == 1.
Fix these leaks by assigning new->usage (and new->subscribers which was added
in 2.6.32) before calling security_prepare_creds().
Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Tetsuo Handa [Mon, 7 Feb 2011 13:36:10 +0000 (13:36 +0000)]
CRED: Fix BUG() upon security_cred_alloc_blank() failure
In cred_alloc_blank() since 2.6.32, abort_creds(new) is called with
new->security == NULL and new->magic == 0 when security_cred_alloc_blank()
returns an error. As a result, BUG() will be triggered if SELinux is enabled
or CONFIG_DEBUG_CREDENTIALS=y.
If CONFIG_DEBUG_CREDENTIALS=y, BUG() is called from __invalid_creds() because
cred->magic == 0. Failing that, BUG() is called from selinux_cred_free()
because selinux_cred_free() is not expecting cred->security == NULL. This does
not affect smack_cred_free(), tomoyo_cred_free() or apparmor_cred_free().
Fix these bugs by
(1) Set new->magic before calling security_cred_alloc_blank().
(2) Handle null cred->security in creds_are_invalid() and selinux_cred_free().
Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Mon, 7 Feb 2011 22:02:06 +0000 (14:02 -0800)]
Merge git://git./linux/kernel/git/sfrench/cifs-2.6
* git://git.kernel.org/pub/scm/linux/kernel/git/sfrench/cifs-2.6:
cifs: remove checks for ses->status == CifsExiting
cifs: add check for kmalloc in parse_dacl
cifs: don't send an echo request unless NegProt has been done
cifs: enable signing flag in SMB header when server has it on
cifs: Possible slab memory corruption while updating extended stats (repost)
CIFS: Fix variable types in cifs_iovec_read/write (try #2)
cifs: fix length vs. total_read confusion in cifs_demultiplex_thread
Yan, Zheng [Tue, 18 Jan 2011 05:34:40 +0000 (13:34 +0800)]
Btrfs: Fix page count calculation
take offset of start position into account when calculating page count.
Signed-off-by: Yan, Zheng <zheng.z.yan@intel.com>
Signed-off-by: Chris Mason <chris.mason@oracle.com>
Russell King [Mon, 7 Feb 2011 19:07:10 +0000 (19:07 +0000)]
Merge branch 'fixes'
Jeff Layton [Mon, 7 Feb 2011 13:54:35 +0000 (08:54 -0500)]
cifs: remove checks for ses->status == CifsExiting
ses->status is never set to CifsExiting, so these checks are
always false.
Tested-by: JG <jg@cms.ac>
Signed-off-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: Steve French <sfrench@us.ibm.com>
Russell King [Mon, 7 Feb 2011 15:15:37 +0000 (15:15 +0000)]
Merge branch 'for-rmk' of git://git.pengutronix.de/git/imx/linux-2.6 into fixes
Russell King [Sat, 5 Feb 2011 10:41:55 +0000 (10:41 +0000)]
ALSA: AACI: allow writes to MAINCR to take effect
The AACI TRM requires the MAINCR enable bit to be held zero for two
bitclk cycles plus three apb_pclk cycles. Use a delay of 1us to
ensure this.
Ensure that writes to MAINCR to change the addressed codec only happen
when required, and that they take effect in a similar manner to the
above, otherwise we seem to occasionally have stuck slot busy bits.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Russell King [Mon, 7 Feb 2011 08:59:29 +0000 (08:59 +0000)]
ARM: Update mach-types
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
H. Peter Anvin [Mon, 7 Feb 2011 05:16:09 +0000 (21:16 -0800)]
x86, nx: Mark the ACPI resume trampoline code as +x
We reserve lowmem for the things that need it, like the ACPI
wakeup code, way early to guarantee availability. This happens
before we set up the proper pagetables, so set_memory_x() has no
effect.
Until we have a better solution, use an initcall to mark the
wakeup code executable.
Originally-by: Matthieu Castet <castet.matthieu@free.fr>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Cc: Matthias Hopf <mhopf@suse.de>
Cc: rjw@sisk.pl
Cc: Suresh Siddha <suresh.b.siddha@intel.com>
LKML-Reference: <
4D4F8019.
2090104@zytor.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Anton Blanchard [Thu, 21 Oct 2010 00:52:12 +0000 (00:52 +0000)]
powerpc: Fix hcall tracepoint recursion
Spinlocks on shared processor partitions use H_YIELD to notify the
hypervisor we are waiting on another virtual CPU. Unfortunately this means
the hcall tracepoints can recurse.
The patch below adds a percpu depth and checks it on both the entry and
exit hcall tracepoints.
Signed-off-by: Anton Blanchard <anton@samba.org>
Acked-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
CC: stable@kernel.org
Anton Blanchard [Sat, 29 Jan 2011 12:37:16 +0000 (12:37 +0000)]
powerpc/numa: Fix bug in unmap_cpu_from_node
When converting to the new cpumask code I screwed up:
- if (cpu_isset(cpu, numa_cpumask_lookup_table[node])) {
- cpu_clear(cpu, numa_cpumask_lookup_table[node]);
+ if (cpumask_test_cpu(cpu, node_to_cpumask_map[node])) {
+ cpumask_set_cpu(cpu, node_to_cpumask_map[node]);
This was introduced in commit
25863de07af9 (powerpc/cpumask: Convert NUMA code
to new cpumask API)
Fix it.
Signed-off-by: Anton Blanchard <anton@samba.org>
Cc: <stable@kernel.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Anton Blanchard [Sat, 29 Jan 2011 12:35:22 +0000 (12:35 +0000)]
powerpc/numa: Disable VPHN on dedicated processor partitions
There is no need to start up the timer and monitor topology changes on a
dedicated processor partition, so disable it.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Anton Blanchard [Sat, 29 Jan 2011 12:28:04 +0000 (12:28 +0000)]
powerpc/numa: Add length when creating OF properties via VPHN
The rest of the NUMA code expects an OF associativity property with
the first cell containing the length. Without this fix all topology changes
cause us to misparse the property and put the cpu into node 0.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Anton Blanchard [Sat, 29 Jan 2011 12:26:19 +0000 (12:26 +0000)]
powerpc/numa: Check for all VPHN changes
The hypervisor uses unsigned 1 byte counters to signal topology changes to
the OS. Since they can wrap we need to check for any difference, not just if
the hypervisor count is greater than the previous count.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Anton Blanchard [Sat, 29 Jan 2011 12:24:34 +0000 (12:24 +0000)]
powerpc/numa: Only use active VPHN count fields
VPHN supports up to 8 distance fields but the number of entries in
ibm,associativity-reference-points signifies how many are in use.
Don't look at all the VPHN counts, only distance_ref_points_depth
worth.
Since we already cap our distance metrics at MAX_DISTANCE_REF_POINTS,
use that to size the VPHN arrays and add a BUILD_BUG_ON to avoid it growing
larger than the VPHN maximum of 8.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Jesse Larrew [Thu, 20 Jan 2011 19:01:35 +0000 (19:01 +0000)]
powerpc/pseries: Remove unnecessary variable initializations in numa.c
Remove unnecessary variable initializations in VPHN functions.
Signed-off-by: Jesse Larrew <jlarrew@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Jesse Larrew [Thu, 20 Jan 2011 19:01:13 +0000 (19:01 +0000)]
powerpc/pseries: Fix brace placement in numa.c
Fix brace placement in VPHN code.
Signed-off-by: Jesse Larrew <jlarrew@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Jesse Larrew [Thu, 20 Jan 2011 19:00:51 +0000 (19:00 +0000)]
powerpc/pseries: Fix typo in VPHN comments
Correct a spelling error in VPHN comments in numa.c.
Signed-off-by: Jesse Larrew <jlarrew@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Benjamin Herrenschmidt [Thu, 20 Jan 2011 20:35:23 +0000 (20:35 +0000)]
powerpc: Fix some 6xx/7xxx CPU setup functions
Some of those functions try to adjust the CPU features, for example
to remove NAP support on some revisions. However, they seem to use
r5 as an index into the CPU table entry, which might have been right
a long time ago but no longer is. r4 is the right register to use.
This probably caused some off behaviours on some PowerMac variants
using 750cx or 7455 processor revisions.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
CC: stable@kernel.org
Benjamin Herrenschmidt [Thu, 20 Jan 2011 20:36:03 +0000 (20:36 +0000)]
powerpc: Pass the right cpu_spec to ->setup_cpu() on 64-bit
When calling setup_cpu() on 64-bit, we pass a pointer to the
cputable entry we have found. This used to be fine when cur_cpu_spec
was a pointer to that entry, but nowadays, we copy the entry into
a separate variable, and we do so before we call the setup_cpu()
callback. That means that any attempt by that callback at patching
the CPU table entry (to adjust CPU features for example) will patch
the wrong table.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Scott Wood [Thu, 27 Jan 2011 10:30:00 +0000 (10:30 +0000)]
powerpc/book3e: Protect complex macro args in mmu-book3e.h
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Scott Wood [Thu, 27 Jan 2011 10:31:38 +0000 (10:31 +0000)]
powerpc: Fix pfn_valid() when memory starts at a non-zero address
max_mapnr is a pfn, not an index innto mem_map[]. So don't add
ARCH_PFN_OFFSET a second time.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Linus Torvalds [Sun, 6 Feb 2011 20:05:58 +0000 (12:05 -0800)]
Merge branch 'ixp4xx' of git://git./linux/kernel/git/chris/linux-2.6
* 'ixp4xx' of git://git.kernel.org/pub/scm/linux/kernel/git/chris/linux-2.6:
arm/ixp4xx: Rename FREQ macro to avoid collisions
IXP4xx: Fix qmgr_release_queue() flushing unexpected queue entries.
Linus Torvalds [Sun, 6 Feb 2011 20:05:15 +0000 (12:05 -0800)]
Merge branch 'timers-fixes-for-linus' of git://git./linux/kernel/git/tip/linux-2.6-tip
* 'timers-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
lockdep, timer: Fix del_timer_sync() annotation
RTC: Prevents a division by zero in kernel code.
Linus Torvalds [Sun, 6 Feb 2011 20:04:49 +0000 (12:04 -0800)]
Merge branch 'irq-fixes-for-linus' of git://git./linux/kernel/git/tip/linux-2.6-tip
* 'irq-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
m32r: Fixup last __do_IRQ leftover
genirq: Add missing status flags to modification mask
Linus Torvalds [Sun, 6 Feb 2011 20:04:16 +0000 (12:04 -0800)]
Merge branch 'perf-fixes-for-linus' of git://git./linux/kernel/git/tip/linux-2.6-tip
* 'perf-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
perf stat: Fix aggreate counter reading accounting
tracing: Replace syscall_meta_data struct array with pointer array
tracepoints: Fix section alignment using pointer array
tracing: Replace trace_event struct array with pointer array
Linus Torvalds [Sun, 6 Feb 2011 20:03:10 +0000 (12:03 -0800)]
Merge branch 'x86-fixes-for-linus' of git://git./linux/kernel/git/tip/linux-2.6-tip
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86-32: Make sure the stack is set up before we use it
x86, mtrr: Avoid MTRR reprogramming on BP during boot on UP platforms
x86, nx: Don't force pages RW when setting NX bits
Linus Torvalds [Sun, 6 Feb 2011 20:02:42 +0000 (12:02 -0800)]
Merge branch 'for-linus' of git://git./linux/kernel/git/tiwai/sound-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6:
ALSA: use linux/io.h to fix compile warnings
ALSA: hda - Fix memory leaks in conexant jack arrays
ASoC: CX20442: fix NULL pointer dereference
ASoC: Amstrad Delta: fix const related build error
ALSA: oxygen: fix output routing on Xonar DG
sound: silent echo'ed messages in Makefile
ASoC: Fix mask/val_mask confusion snd_soc_dapm_put_volsw()
ASoC: DaVinci: fix kernel panic due to uninitialized platform_data
ALSA: HDA: Fix microphone(s) on Lenovo Edge 13
ASoC: Fix module refcount for auxiliary devices
ALSA: HDA: cxt5066 - Use asus model for Asus U50F, select correct SPDIF output
ALSA: HDA: Add a new model "asus" for Conexant 5066/205xx
ALSA: HDA: Refactor some redundant code for Conexant 5066/205xx
Ben Hutchings [Sat, 11 Dec 2010 20:17:54 +0000 (20:17 +0000)]
arm/ixp4xx: Rename FREQ macro to avoid collisions
FREQ is a ridiculously short name for a platform-specific macro in a
generic header, and it now conflicts with an enumeration in the
gspca/ov519 driver.
Also delete conditional reference to ixp4xx_get_board_tick_rate()
which is not defined anywhere.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Krzysztof Hałasa <khc@pm.waw.pl>
Krzysztof Hałasa [Mon, 3 May 2010 21:22:06 +0000 (23:22 +0200)]
IXP4xx: Fix qmgr_release_queue() flushing unexpected queue entries.
Queues should be empty when released, if not, there is a safety valve.
Make sure the queue is usable after it triggers.
Signed-off-by: Krzysztof Hałasa <khc@pm.waw.pl>
Alexey Charkov [Wed, 2 Feb 2011 21:15:35 +0000 (21:15 +0000)]
btrfs: Drop __exit attribute on btrfs_exit_compress
As this function is called in some error paths while not
removing the module, the __exit attribute prevents the kernel
image from linking when btrfs is compiled in statically.
Signed-off-by: Alexey Charkov <alchark@gmail.com>
Signed-off-by: Chris Mason <chris.mason@oracle.com>
Tsutomu Itoh [Thu, 3 Feb 2011 03:16:25 +0000 (03:16 +0000)]
btrfs: cleanup error handling in btrfs_unlink_inode()
When btrfs_alloc_path() fails, btrfs_free_path() need not be called.
Therefore, it changes the branch ahead.
Signed-off-by: Tsutomu Itoh <t-itoh@jp.fujitsu.com>
Signed-off-by: Chris Mason <chris.mason@oracle.com>
Josef Bacik [Wed, 2 Feb 2011 15:53:47 +0000 (15:53 +0000)]
Btrfs: exclude super blocks when we read in block groups
This has been resulting in a BUT_ON(ret) after btrfs_reserve_extent in
btrfs_cow_file_range. The reason is we don't actually calculate the bytes_super
for a block group until we go to cache it, which means that the space_info can
hand out reservations for space that it doesn't actually have, and we can run
out of data space. This is also a problem if you are using space caching since
we don't ever calculate bytes_super for the block groups. So instead everytime
we read a block group call exclude_super_stripes, which calculates the
bytes_super for the block group so it can be left out of the space_info. Then
whenever caching completes we just call free_excluded_extents so that the super
excluded extents are freed up. Also if we are unmounting and we hit any block
groups that haven't been cached we still need to call free_excluded_extents to
make sure things are cleaned up properly. Thanks,
Reported-by: Arne Jansen <sensille@gmx.net>
Signed-off-by: Josef Bacik <josef@redhat.com>
Signed-off-by: Chris Mason <chris.mason@oracle.com>
Josef Bacik [Thu, 3 Feb 2011 02:39:52 +0000 (02:39 +0000)]
Btrfs: make sure search_bitmap finds something in remove_from_bitmap
When we're cleaning up the tree log we need to be able to remove free space from
the block group. The problem is if that free space spans bitmaps we would not
find the space since we're looking for too many bytes. So make sure the amount
of bytes we search for is limited to either the number of bytes we want, or the
number of bytes left in the bitmap. This was tested by a user who was hitting
the BUG() after search_bitmap. With this patch he can now mount his fs.
Thanks,
Signed-off-by: Josef Bacik <josef@redhat.com>
Signed-off-by: Chris Mason <chris.mason@oracle.com>
Ingo Molnar [Sun, 6 Feb 2011 11:59:22 +0000 (12:59 +0100)]
Merge branch 'timers/locking'
Stanislav Fomichev [Sat, 5 Feb 2011 23:05:28 +0000 (02:05 +0300)]
cifs: add check for kmalloc in parse_dacl
Exit from parse_dacl if no memory returned from the call to kmalloc.
Signed-off-by: Stanislav Fomichev <kernel@fomichev.me>
Signed-off-by: Steve French <sfrench@us.ibm.com>
Thomas Gleixner [Sat, 5 Feb 2011 20:39:28 +0000 (21:39 +0100)]
m32r: Fixup last __do_IRQ leftover
Somehow I managed to miss the last __do_IRQ caller when I cleanup the
remaining users. m32r is fully converted to the generic irq layer, but
I managed to not commit the conversion of __do_IRQ() to
generic_handle_irq() after compile testing the quilt series :(
Pointed-out-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Hirokazu Takata <takata@linux-m32r.org>
Cc: Paul Mundt <lethal@linux-sh.org>
Thomas Gleixner [Sat, 5 Feb 2011 15:25:25 +0000 (16:25 +0100)]
genirq: Add missing status flags to modification mask
The mask which filters out the valid bits which can be set via
irq_modify_status() is missing IRQ_NO_BALANCING, which breaks UV.
Add IRQ_PER_CPU as well to avoid another one line patch for 39.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Mika Westerberg [Sat, 5 Feb 2011 08:52:33 +0000 (09:52 +0100)]
ARM: 6652/1: ep93xx: correct the end address of the AC97 memory resource
The last register is at offset 0xa8 making the resource end to be 0xac - 1
instead of 0xb0 - 1.
Signed-off-by: Mika Westerberg <mika.westerberg@iki.fi>
Acked-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
H. Peter Anvin [Sat, 5 Feb 2011 00:14:11 +0000 (16:14 -0800)]
x86-32: Make sure the stack is set up before we use it
Since checkin
ebba638ae723d8a8fc2f7abce5ec18b688b791d7 we call
verify_cpu even in 32-bit mode. Unfortunately, calling a function
means using the stack, and the stack pointer was not initialized in
the 32-bit setup code! This code initializes the stack pointer, and
simplifies the interface slightly since it is easier to rely on just a
pointer value rather than a descriptor; we need to have different
values for the segment register anyway.
This retains start_stack as a virtual address, even though a physical
address would be more convenient for 32 bits; the 64-bit code wants
the other way around...
Reported-by: Matthieu Castet <castet.matthieu@free.fr>
LKML-Reference: <
4D41E86D.
8060205@free.fr>
Tested-by: Kees Cook <kees.cook@canonical.com>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Jeff Layton [Fri, 4 Feb 2011 22:09:50 +0000 (17:09 -0500)]
cifs: don't send an echo request unless NegProt has been done
When the socket to the server is disconnected, the client more or less
immediately calls cifs_reconnect to reconnect the socket. The NegProt
and SessSetup however are not done until an actual call needs to be
made.
With the addition of the SMB echo code, it's possible that the server
will initiate a disconnect on an idle socket. The client will then
reconnect the socket but no NegotiateProtocol request is done. The
SMBEcho workqueue job will then eventually pop, and an SMBEcho will be
sent on the socket. The server will then reject it since no NegProt was
done.
The ideal fix would be to either have the socket not be reconnected
until we plan to use it, or to immediately do a NegProt when the
reconnect occurs. The code is not structured for this however. For now
we must just settle for not sending any echoes until the NegProt is
done.
Reported-by: JG <jg@cms.ac>
Signed-off-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: Steve French <sfrench@us.ibm.com>
Linus Torvalds [Fri, 4 Feb 2011 21:20:01 +0000 (13:20 -0800)]
Merge git://git./linux/kernel/git/davem/net-2.6
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (68 commits)
net: can: janz-ican3: world-writable sysfs termination file
net: can: at91_can: world-writable sysfs files
MAINTAINERS: update email ids of the be2net driver maintainers.
bridge: Don't put partly initialized fdb into hash
r8169: prevent RxFIFO induced loops in the irq handler.
r8169: RxFIFO overflow oddities with 8168 chipsets.
r8169: use RxFIFO overflow workaround for 8168c chipset.
include/net/genetlink.h: Allow genlmsg_cancel to accept a NULL argument
net: Provide compat support for SIOCGETMIFCNT_IN6 and SIOCGETSGCNT_IN6.
net: Support compat SIOCGETVIFCNT ioctl in ipv4.
net: Fix bug in compat SIOCGETSGCNT handling.
niu: Fix races between up/down and get_stats.
tcp_ecn is an integer not a boolean
atl1c: Add missing PCI device ID
s390: Fix possibly wrong size in strncmp (smsgiucv)
s390: Fix wrong size in memcmp (netiucv)
qeth: allow OSA CHPARM change in suspend state
qeth: allow HiperSockets framesize change in suspend
qeth: add more strict MTU checking
qeth: show new mac-address if its setting fails
...
Vasiliy Kulikov [Fri, 4 Feb 2011 02:23:53 +0000 (02:23 +0000)]
net: can: janz-ican3: world-writable sysfs termination file
Don't allow everybody to set terminator via sysfs.
Signed-off-by: Vasiliy Kulikov <segoon@openwall.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vasiliy Kulikov [Fri, 4 Feb 2011 02:23:50 +0000 (02:23 +0000)]
net: can: at91_can: world-writable sysfs files
Don't allow everybody to write to mb0_id file.
Signed-off-by: Vasiliy Kulikov <segoon@openwall.com>
Acked-by: Kurt Van Dijck <kurt.van.dijck@eia.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ajit Khaparde [Fri, 4 Feb 2011 21:03:35 +0000 (13:03 -0800)]
MAINTAINERS: update email ids of the be2net driver maintainers.
Signed-off-by: Ajit Khaparde <ajit.khaparde@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pavel Emelyanov [Fri, 4 Feb 2011 21:02:36 +0000 (13:02 -0800)]
bridge: Don't put partly initialized fdb into hash
The fdb_create() puts a new fdb into hash with only addr set. This is
not good, since there are callers, that search the hash w/o the lock
and access all the other its fields.
Applies to current netdev tree.
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Layton [Fri, 4 Feb 2011 12:21:26 +0000 (07:21 -0500)]
cifs: enable signing flag in SMB header when server has it on
cifs_sign_smb only generates a signature if the correct Flags2 bit is
set. Make sure that it gets set correctly if we're sending an async
call.
This patch fixes:
https://bugzilla.kernel.org/show_bug.cgi?id=28142
Reported-and-Tested-by: JG <jg@cms.ac>
Signed-off-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: Steve French <sfrench@us.ibm.com>
Shirish Pargaonkar [Thu, 3 Feb 2011 20:31:18 +0000 (14:31 -0600)]
cifs: Possible slab memory corruption while updating extended stats (repost)
Updating extended statistics here can cause slab memory corruption
if a callback function frees slab memory (mid_entry).
Signed-off-by: Shirish Pargaonkar <shirishpargaonkar@gmail.com>
Reviewed-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: Steve French <sfrench@us.ibm.com>
Tetsuo Handa [Fri, 4 Feb 2011 18:13:24 +0000 (18:13 +0000)]
CRED: Fix kernel panic upon security_file_alloc() failure.
In get_empty_filp() since 2.6.29, file_free(f) is called with f->f_cred == NULL
when security_file_alloc() returned an error. As a result, kernel will panic()
due to put_cred(NULL) call within RCU callback.
Fix this bug by assigning f->f_cred before calling security_file_alloc().
Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
projects / GitHub / MotorolaMobilityLLC / kernel-slsi.git / log