GitHub/mt8127/android_kernel_alcatel_ttab.git
17 years ago[SPARC64]: Really fix parport.
David S. Miller [Wed, 13 Jun 2007 06:53:03 +0000 (23:53 -0700)]
[SPARC64]: Really fix parport.

We were passing a "struct pci_dev *" instead of a
"struct device *" to the parport registry routines.
No wonder things exploded.

The ebus_bus_type hacks can be backed out from
asm-sparc64/dma-mapping.h, those were wrong.

Signed-off-by: David S. Miller <davem@davemloft.net>
17 years ago[SPARC64]: Fix IO/MEM space sizing for PCI.
David S. Miller [Tue, 12 Jun 2007 23:54:08 +0000 (16:54 -0700)]
[SPARC64]: Fix IO/MEM space sizing for PCI.

In pci_determine_mem_io_space(), do not hard code the region sizes.
Instead, use the values given to us in the ranges property.

Thanks goes to Mikael Petterson for the original Xorg failure
bug repoert, and strace dumps from Mikael and Dmitry Artamonow.

Signed-off-by: David S. Miller <davem@davemloft.net>
17 years ago[SPARC64]: Wire up cookie based sun4v interrupt registry.
David S. Miller [Wed, 13 Jun 2007 07:01:04 +0000 (00:01 -0700)]
[SPARC64]: Wire up cookie based sun4v interrupt registry.

This will be used for logical domain channel interrupts.

Signed-off-by: David S. Miller <davem@davemloft.net>
17 years agoMerge branch 'upstream-linus' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik...
Linus Torvalds [Wed, 13 Jun 2007 03:35:10 +0000 (20:35 -0700)]
Merge branch 'upstream-linus' of /linux/kernel/git/jgarzik/netdev-2.6

* 'upstream-linus' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/netdev-2.6: (89 commits)
  myri10ge: update driver version
  myri10ge: report when the link partner is running in Myrinet mode
  myri10ge: limit the number of recoveries
  NetXen: Fix link status messages
  Revert "[netdrvr e100] experiment with doing RX in a similar manner to eepro100"
  [PATCH] libertas: convert libertas_mpp into anycast_mask
  [PATCH] libertas: actually send mesh frames to mesh netdev
  [PATCH] libertas: deauthenticate from AP in channel switch
  [PATCH] libertas: pull current channel from firmware on mesh autostart
  [PATCH] libertas: reduce SSID and BSSID mixed-case abuse
  [PATCH] libertas: remove WPA_SUPPLICANT structure
  [PATCH] libertas: remove structure WLAN_802_11_SSID and libertas_escape_essid
  [PATCH] libertas: tweak association debug output
  [PATCH] libertas: fix big-endian associate command.
  [PATCH] libertas: don't byte-swap firmware version number. It's a byte array.
  [PATCH] libertas: more endianness fixes, in tx.c this time
  [PATCH] libertas: More endianness fixes.
  [PATCH] libertas: first pass at fixing up endianness issues
  [PATCH] libertas: sparse fixes
  [PATCH] libertas: fix character set in README
  ...

17 years agoMerge branch 'master' into upstream-fixes
Jeff Garzik [Wed, 13 Jun 2007 02:34:34 +0000 (22:34 -0400)]
Merge branch 'master' into upstream-fixes

17 years agoMerge branch 'libertas-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/linvil...
Jeff Garzik [Wed, 13 Jun 2007 02:27:52 +0000 (22:27 -0400)]
Merge branch 'libertas-fixes' of git://git./linux/kernel/git/linville/wireless-2.6 into upstream-fixes

17 years agoMerge branch 'libertas' of git://git.kernel.org/pub/scm/linux/kernel/git/linville...
Jeff Garzik [Wed, 13 Jun 2007 02:27:30 +0000 (22:27 -0400)]
Merge branch 'libertas' of git://git./linux/kernel/git/linville/wireless-2.6 into upstream-fixes

17 years agosysfs: fix race condition around sd->s_dentry, take#2
Tejun Heo [Mon, 11 Jun 2007 05:04:01 +0000 (14:04 +0900)]
sysfs: fix race condition around sd->s_dentry, take#2

Allowing attribute and symlink dentries to be reclaimed means
sd->s_dentry can change dynamically.  However, updates to the field
are unsynchronized leading to race conditions.  This patch adds
sysfs_lock and use it to synchronize updates to sd->s_dentry.

Due to the locking around ->d_iput, the check in sysfs_drop_dentry()
is complex.  sysfs_lock only protect sd->s_dentry pointer itself.  The
validity of the dentry is protected by dcache_lock, so whether dentry
is alive or not can only be tested while holding both locks.

This is minimal backport of sysfs_drop_dentry() rewrite in devel
branch.

Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
17 years agosysfs: fix condition check in sysfs_drop_dentry()
Tejun Heo [Mon, 11 Jun 2007 05:03:27 +0000 (14:03 +0900)]
sysfs: fix condition check in sysfs_drop_dentry()

The condition check doesn't make much sense as it basically always
succeeds.  This causes NULL dereferencing on certain cases.  It seems
that parentheses are put in the wrong place.  Fix it.

Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
17 years agosysfs: store sysfs inode nrs in s_ino to avoid readdir oopses
Eric Sandeen [Mon, 11 Jun 2007 05:02:45 +0000 (14:02 +0900)]
sysfs: store sysfs inode nrs in s_ino to avoid readdir oopses

Backport of
ftp://ftp.kernel.org/pub/linux/kernel/people/akpm/patches/2.6/2.6.22-rc1/2.6.22-rc1-mm1/broken-out/gregkh-driver-sysfs-allocate-inode-number-using-ida.patch

For regular files in sysfs, sysfs_readdir wants to traverse
sysfs_dirent->s_dentry->d_inode->i_ino to get to the inode number.
But, the dentry can be reclaimed under memory pressure, and there is
no synchronization with readdir.  This patch follows Tejun's scheme of
allocating and storing an inode number in the new s_ino member of a
sysfs_dirent, when dirents are created, and retrieving it from there
for readdir, so that the pointer chain doesn't have to be traversed.

Tejun's upstream patch uses a new-ish "ida" allocator which brings
along some extra complexity; this -stable patch has a brain-dead
incrementing counter which does not guarantee uniqueness, but because
sysfs doesn't hash inodes as iunique expects, uniqueness wasn't
guaranteed today anyway.

Signed-off-by: Eric Sandeen <sandeen@redhat.com>
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
17 years agomyri10ge: update driver version
Brice Goglin [Mon, 11 Jun 2007 18:27:07 +0000 (20:27 +0200)]
myri10ge: update driver version

Update myri10ge driver version to 1.3.1-1.248.

Signed-off-by: Brice Goglin <brice@myri.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
17 years agomyri10ge: report when the link partner is running in Myrinet mode
Brice Goglin [Mon, 11 Jun 2007 18:26:50 +0000 (20:26 +0200)]
myri10ge: report when the link partner is running in Myrinet mode

Since Myri-10G boards may also run in Myrinet mode instead of Ethernet,
add a message when we detect that the link partner is not running in the
right mode.

Signed-off-by: Brice Goglin <brice@myri.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
17 years agomyri10ge: limit the number of recoveries
Brice Goglin [Mon, 11 Jun 2007 18:26:31 +0000 (20:26 +0200)]
myri10ge: limit the number of recoveries

Limit the number of recoveries from a NIC hw watchdog reset to 1 by default.
It enables detection of defective NICs immediately since these memory parity
errors are expected to happen very rarely (less than once per century*NIC).

Signed-off-by: Brice Goglin <brice@myri.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
17 years agoNetXen: Fix link status messages
Mithlesh Thukral [Mon, 11 Jun 2007 10:30:58 +0000 (03:30 -0700)]
NetXen: Fix link status messages

NetXen: Fix incorrect link status even with switch turned OFF.
NetXen driver failed to accurately indicate when a link is up or down.
This was encountered during failover testing, when the first port
indicated that the link was up even when the 10G switch it was assigned
to in the Bladecenter was turned off completely.

Signed-off by: Wen Xiong <wenxiong@us.ibm.com>
Signed-off by: Mithlesh Thukral <mithlesh@netxen.com>

Signed-off-by: Jeff Garzik <jeff@garzik.org>
17 years agoRevert "[netdrvr e100] experiment with doing RX in a similar manner to eepro100"
Jeff Garzik [Tue, 12 Jun 2007 22:52:31 +0000 (18:52 -0400)]
Revert "[netdrvr e100] experiment with doing RX in a similar manner to eepro100"

This reverts commit d52df4a35af569071fda3f4eb08e47cc7023f094.

This patch attempted to fix e100 for non-cache coherent memory
architectures by using the cb style code that eepro100 had and using
the EL and s bits from the RFD list. Unfortunately the hardware
doesn't work exactly like this and therefore this patch actually
breaks e100. Reverting the change brings it back to the previously
known good state for 2.6.22. The pending rewrite in progress to this
code can then be safely merged later.

Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
17 years ago[PATCH] libertas: convert libertas_mpp into anycast_mask
Luis Carlos [Thu, 7 Jun 2007 20:40:59 +0000 (16:40 -0400)]
[PATCH] libertas: convert libertas_mpp into anycast_mask

With firmware 5.220.11.p5, this allows to specify the anycast addresses the
device will listen to.

The anycast address range is C0:27:C0:27:C0:XX where XX goes from 00 to 1F (or
0 to 31 in dec). The value to write on anycast_mask will specify which
addresses the device listens to. Bits in a 32 bit int are numbered from 0
(least significative bit) to 31. A specific address ending in YY will be
listened to if bit YY in the value is set to one.

Examples:

0x00000000 : do not listen to any anycast address
0xFFFFFFFF : listen to every anycast address from :00 to :1F
0x00000013 : listen to anycast addresses :00, :01 and :04

Signed-off-by: Luis Carlos Cobo <luisca@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
17 years ago[PATCH] libertas: actually send mesh frames to mesh netdev
Dan Williams [Tue, 5 Jun 2007 00:05:23 +0000 (20:05 -0400)]
[PATCH] libertas: actually send mesh frames to mesh netdev

Found by Luis; got broken during module split.

Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
17 years ago[PATCH] libertas: deauthenticate from AP in channel switch
Luis Carlos Cobo Rus [Wed, 30 May 2007 16:16:13 +0000 (12:16 -0400)]
[PATCH] libertas: deauthenticate from AP in channel switch

This avoids channel mismatch between driver and firmware in case we change
channel while associated to an AP.

Signed-off-by: Luis Carlos Cobo Rus <luisca@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
17 years ago[PATCH] libertas: pull current channel from firmware on mesh autostart
Luis Carlos Cobo Rus [Wed, 30 May 2007 16:14:34 +0000 (12:14 -0400)]
[PATCH] libertas: pull current channel from firmware on mesh autostart

Signed-off-by: Luis Carlos Cobo Rus <luisca@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
17 years agoMerge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland...
Linus Torvalds [Mon, 11 Jun 2007 22:46:08 +0000 (15:46 -0700)]
Merge branch 'for-linus' of git://git./linux/kernel/git/roland/infiniband

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband:
  IB/mlx4: Make sure RQ allocation is always valid
  RDMA/cma: Fix initialization of next_port
  IB/mlx4: Fix zeroing of rnr_retry value in ib_modify_qp()
  mlx4_core: Don't set MTT address in dMPT entries with PA set
  mlx4_core: Check firmware command interface revision
  IB/mthca, mlx4_core: Fix typo in comment
  mlx4_core: Free catastrophic error MSI-X interrupt with correct dev_id
  mlx4_core: Initialize ctx_list and ctx_lock earlier
  mlx4_core: Fix CQ context layout

17 years agoMerge branch 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus
Linus Torvalds [Mon, 11 Jun 2007 18:41:00 +0000 (11:41 -0700)]
Merge branch 'upstream' of git://ftp.linux-mips.org/upstream-linus

* 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus:
  [MIPS] Fix smp barriers in test_and_{change,clear,set}_bit
  [MIPS] Fix IP27 build
  [MIPS] Fix modpost warnings by making start_secondary __cpuinit
  [MIPS] SMTC: Fix build error caused by nonsense code.
  [MIPS] SMTC: The MT ASE requires to initialize c0_pagemask and c0_wired.
  [MIPS] SMTC: Don't continue in set_vi_srs_handler on detected bad arguments.
  [MIPS] SMTC: Fix warning.
  [MIPS] Wire up utimensat, signalfd, timerfd, eventfd
  [MIPS] Atlas: Fix build.
  [MIPS] Always install the DSP exception handler.
  [MIPS] SMTC: Don't set and restore irqregs ptr from self_ipi.
  [MIPS] Fix KMODE for the R3000

17 years agoMerge git://git.kernel.org/pub/scm/linux/kernel/git/sfrench/cifs-2.6
Linus Torvalds [Mon, 11 Jun 2007 18:39:25 +0000 (11:39 -0700)]
Merge git://git./linux/kernel/git/sfrench/cifs-2.6

* git://git.kernel.org/pub/scm/linux/kernel/git/sfrench/cifs-2.6:
  [CIFS] CIFS should honour umask
  [CIFS] Missing flag on negprot needed for some servers to force packet signing
  [CIFS] whitespace cleanup part 2
  [CIFS] whitespace cleanup
  [CIFS] fix mempool destroy done in wrong order in cifs error path
  [CIFS] typo in previous patch
  [CIFS] Fix oops on failed cifs mount (in kthread_stop)

17 years agoMerge master.kernel.org:/pub/scm/linux/kernel/git/davej/agpgart
Linus Torvalds [Mon, 11 Jun 2007 18:39:05 +0000 (11:39 -0700)]
Merge /pub/scm/linux/kernel/git/davej/agpgart

* master.kernel.org:/pub/scm/linux/kernel/git/davej/agpgart:
  [AGPGART] intel_agp: Add support for G33, Q33 and Q35 chipsets
  [AGPGART] intel_agp: add support for 945GME
  [AGPGART] intel_agp: add support for 965GME/GLE
  [AGPGART] intel_agp: use table for device probe
  [AGPGART] intel_agp: cleanup intel private data

17 years agoMerge branch 'linus-plus-plus' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik...
Linus Torvalds [Mon, 11 Jun 2007 18:38:14 +0000 (11:38 -0700)]
Merge branch 'linus-plus-plus' of /linux/kernel/git/jgarzik/libata-dev

* 'linus-plus-plus' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/libata-dev:
  libata: limit post SRST nsect/lbal wait to ~100ms
  libata: force PIO on IOMEGA ZIP 250 ATAPI
  libata passthru: update cached device paramters
  libata passthru: always enforce correct DEV bit
  libata passthru: map UDMA protocols
  libata passthru: support PIO multi commands
  libata passthru: update protocol numbers
  libata: Correct abuse of language
  libata-core/sff: Fix multiple assumptions about DMA
  ahci: Add MCP73/MCP77 support to AHCI driver
  libata: fix hw_sata_spd_limit initialization
  libata: print device model and firmware revision for ATAPI devices
  libata: fix probe time irq printouts
  libata: disable NCQ for HITACHI HTS541680J9SA00/SB21C7EP
  remove unused variable in pata_isapnp

17 years agoMerge branch 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/v4l-dvb
Linus Torvalds [Mon, 11 Jun 2007 18:32:28 +0000 (11:32 -0700)]
Merge branch 'master' of git://git./linux/kernel/git/mchehab/v4l-dvb

* 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/v4l-dvb:
  V4L/DVB (5751): Ivtv: fix ia64 printk format warnings.
  V4L/DVB (5761): Fix broken b2c2 dependency on non x86 architectures
  V4L/DVB (5673): Fix audio stuttering for saa711x/ivtv when in radio mode.
  V4L/DVB (5736): Add V4L2_FBUF_CAP/FLAG_LOCAL/GLOBAL_INV_ALPHA
  V4L/DVB (5732): Add ivtv CROPCAP support and fix ivtv S_CROP for video output.
  V4L/DVB (5730): Remove unused V4L2_CAP_VIDEO_OUTPUT_POS
  V4L/DVB (5720): Usbvision: fix urb allocation and submits
  V4L/DVB (5716): Tda10086,tda826x: fix tuning, STR/SNR values
  V4L/DVB (5675): Move big PIO accesses from the interrupt handler to a workhandler
  V4L/DVB (5699): Cinergyt2: fix file release handler
  V4L/DVB (5700): Saa7111: fix picture settings cache bug
  V4L/DVB (5702): Fix Kconfig items to avoid linkedition errors

17 years agoMerge master.kernel.org:/pub/scm/linux/kernel/git/bart/ide-2.6
Linus Torvalds [Mon, 11 Jun 2007 18:31:43 +0000 (11:31 -0700)]
Merge /pub/scm/linux/kernel/git/bart/ide-2.6

* master.kernel.org:/pub/scm/linux/kernel/git/bart/ide-2.6:
  ide: Add the MCP73/77 support to PATA driver
  Add the PATA controller device ID to pci_ids.h for MCP73/MCP77.
  hpt366: disallow Ultra133 for HPT374
  ide: generic IDE PCI driver, add another device exception
  ide: HPA detect from resume
  it821x: RAID mode fixes
  serverworks: fix CSB6 tuning logic
  serverworks: remove crappy code

17 years agoMerge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/drzeus/mmc
Linus Torvalds [Mon, 11 Jun 2007 18:31:18 +0000 (11:31 -0700)]
Merge branch 'for-linus' of git://git./linux/kernel/git/drzeus/mmc

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/drzeus/mmc:
  mmc: don't call switch on old cards
  mmc: fix broken if clause
  au1xmmc: Replace C code with call to ARRAY_SIZE() macro.
  mmc-atmel: remove linux/mmc/protocol.h dependencies

17 years agoMerge branch 'splice-2.6.22' of git://git.kernel.dk/data/git/linux-2.6-block
Linus Torvalds [Mon, 11 Jun 2007 18:31:05 +0000 (11:31 -0700)]
Merge branch 'splice-2.6.22' of git://git.kernel.dk/data/git/linux-2.6-block

* 'splice-2.6.22' of git://git.kernel.dk/data/git/linux-2.6-block:
  splice: __generic_file_splice_read: fix read/truncate race
  splice: __generic_file_splice_read: fix i_size_read() length checks
  splice: move balance_dirty_pages_ratelimited() outside of splice actor
  pipe: move pipe_inode_info structure decleration up before it's used
  splice: remove do_splice_direct() symbol export
  splice: move inode size check into generic_file_splice_read()

17 years ago[PATCH] libertas: reduce SSID and BSSID mixed-case abuse
Dan Williams [Tue, 29 May 2007 04:03:31 +0000 (00:03 -0400)]
[PATCH] libertas: reduce SSID and BSSID mixed-case abuse

Kill mixed case function names from scan.c/scan.h.

Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
17 years ago[PATCH] libertas: remove WPA_SUPPLICANT structure
Dan Williams [Tue, 29 May 2007 03:56:10 +0000 (23:56 -0400)]
[PATCH] libertas: remove WPA_SUPPLICANT structure

Unused.

Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
17 years ago[PATCH] libertas: remove structure WLAN_802_11_SSID and libertas_escape_essid
Dan Williams [Tue, 29 May 2007 03:54:55 +0000 (23:54 -0400)]
[PATCH] libertas: remove structure WLAN_802_11_SSID and libertas_escape_essid

Replace WLAN_802_11_SSID with direct 'ssid' and 'ssid_len' members
like ieee80211.  In the process, remove private libertas_escape_essid
and depend on the ieee80211 implementation of escape_essid instead.

Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
17 years ago[PATCH] libertas: tweak association debug output
Dan Williams [Sat, 26 May 2007 03:51:12 +0000 (23:51 -0400)]
[PATCH] libertas: tweak association debug output

Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
17 years ago[PATCH] libertas: fix big-endian associate command.
David Woodhouse [Sat, 26 May 2007 03:41:16 +0000 (23:41 -0400)]
[PATCH] libertas: fix big-endian associate command.

Byte-swapping length fields and then passing them to memcpy() considered
harmful.

Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
17 years ago[PATCH] libertas: don't byte-swap firmware version number. It's a byte array.
David Woodhouse [Sat, 26 May 2007 03:40:21 +0000 (23:40 -0400)]
[PATCH] libertas: don't byte-swap firmware version number. It's a byte array.

Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
17 years ago[PATCH] libertas: more endianness fixes, in tx.c this time
David Woodhouse [Sat, 26 May 2007 03:39:34 +0000 (23:39 -0400)]
[PATCH] libertas: more endianness fixes, in tx.c this time

Now we finally get connectivity. For a while, before something else dies...

Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
17 years ago[PATCH] libertas: More endianness fixes.
David Woodhouse [Sat, 26 May 2007 03:38:14 +0000 (23:38 -0400)]
[PATCH] libertas: More endianness fixes.

Now it at least manages to load the firmware.

Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
17 years ago[PATCH] libertas: first pass at fixing up endianness issues
David Woodhouse [Sat, 26 May 2007 03:36:54 +0000 (23:36 -0400)]
[PATCH] libertas: first pass at fixing up endianness issues

Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
17 years ago[PATCH] libertas: sparse fixes
Dan Williams [Sat, 26 May 2007 03:23:43 +0000 (23:23 -0400)]
[PATCH] libertas: sparse fixes

Fix various issues reported by sparse.

Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
17 years ago[PATCH] libertas: fix character set in README
David Woodhouse [Sat, 26 May 2007 03:15:27 +0000 (23:15 -0400)]
[PATCH] libertas: fix character set in README

Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
17 years ago[PATCH] libertas: support for mesh autostart on firmware 5.220.11
Luis Carlos Cobo Rus [Sat, 26 May 2007 03:12:19 +0000 (23:12 -0400)]
[PATCH] libertas: support for mesh autostart on firmware 5.220.11

Signed-off-by: Luis Carlos Cobo Rus <luisca@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
17 years ago[PATCH] libertas: split wext for eth and msh
Luis Carlos Cobo Rus [Sat, 26 May 2007 03:08:34 +0000 (23:08 -0400)]
[PATCH] libertas: split wext for eth and msh

Separate wireless handlers of mshX and ethX. ethX remains as before.

For mshX, it has been disabled set/get essid, wap and set mode. Get mode always
returns "Repeater" and by now we use the Nickname to show if the mesh is active
("Mesh") or not (empty). The rest remains as before.

Signed-off-by: Luis Carlos Cobo Rus <luisca@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
17 years ago[PATCH] libertas: make mac address configuration work with mesh interface too
Luis Carlos Cobo Rus [Sat, 26 May 2007 03:05:27 +0000 (23:05 -0400)]
[PATCH] libertas: make mac address configuration work with mesh interface too

Signed-off-by: Luis Carlos Cobo Rus <luiscarlos@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
17 years ago[PATCH] libertas: updated readme file
Luis Carlos Cobo Rus [Sat, 26 May 2007 03:04:13 +0000 (23:04 -0400)]
[PATCH] libertas: updated readme file

Fix some wording and blinding table command options, clarify argument list for
fwt_add and fwt_list, simplify fwt_list_route

Signed-off-by: Luis Carlos Cobo Rus <luisca@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
17 years ago[PATCH] libertas: Make WPA work through supplicant handshake
Dan Williams [Sat, 26 May 2007 03:01:24 +0000 (23:01 -0400)]
[PATCH] libertas: Make WPA work through supplicant handshake

Fix WPA so it works up through the supplicant 4-Way handshake process.
Doesn't successfully pass traffic yet; may be problems installing
the GTK to the firmware.

- RSN needs to be enabled before the association command is sent
- Use keys from the association request not the adapter structure
- cmd_act_mac_strict_protection_enable != IW_AUTH_DROP_UNENCRYPTED
- Fix network filtering logic in is_network_compatible() WPA helpers

Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
17 years ago[PATCH] libertas: add more verbose debugging to libertas_cmd_80211_authenticate
Dan Williams [Sat, 26 May 2007 02:58:55 +0000 (22:58 -0400)]
[PATCH] libertas: add more verbose debugging to libertas_cmd_80211_authenticate

Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
17 years ago[PATCH] libertas: debug print spacing fixes in assoc.c
Dan Williams [Sat, 26 May 2007 02:54:50 +0000 (22:54 -0400)]
[PATCH] libertas: debug print spacing fixes in assoc.c

Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
17 years ago[PATCH] libertas: send SIOCGIWSCAN event after partial scans too
Dan Williams [Sat, 26 May 2007 02:38:41 +0000 (22:38 -0400)]
[PATCH] libertas: send SIOCGIWSCAN event after partial scans too

Any time the driver gets new scan results, even from partial scans,
it should send the scan event to userspace.

Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
17 years ago[PATCH] libertas: honor specific channel requests during association
Dan Williams [Sat, 26 May 2007 02:30:48 +0000 (22:30 -0400)]
[PATCH] libertas: honor specific channel requests during association

Previously if a fixed channel was specified along with an SSID,
the channel request would be ignored during the association
process.  Instead, when searching for an adhoc or infrastructure
network to join, allow filtering results based on channel so
that the driver doesn't pick a BSS on a different channel than
requested.

Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
17 years ago[PATCH] libertas: fix default adhoc channel
Dan Williams [Sat, 26 May 2007 02:19:59 +0000 (22:19 -0400)]
[PATCH] libertas: fix default adhoc channel

Inadvertently removed on a previous commit; causes the first
adhoc start to fail if a channel has not been set or no
other association has been made.

Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
17 years ago[PATCH] libertas: fix deadlock SIOCGIWSCAN handler
Dan Williams [Sat, 26 May 2007 02:18:47 +0000 (22:18 -0400)]
[PATCH] libertas: fix deadlock SIOCGIWSCAN handler

Update signal quality before the locked scan result translation loop,
because calling libertas_prepare_and_send_command() with the
'waitforrsp' option grabs adapter->lock in the command return processing,
leading to the deadlock.

Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
17 years ago[PATCH] libertas: correct error report paths for wlan_fwt_list_ioctl
Dan Williams [Sat, 26 May 2007 01:59:29 +0000 (21:59 -0400)]
[PATCH] libertas: correct error report paths for wlan_fwt_list_ioctl

Ensure the leave debug print gets triggered when necessary.

Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
17 years ago[PATCH] libertas: correctly balance locking in libertas_process_rx_command
Dan Williams [Fri, 25 May 2007 21:33:28 +0000 (17:33 -0400)]
[PATCH] libertas: correctly balance locking in libertas_process_rx_command

adapter->lock should released after unlocking adapter->driver_lock to
balance the order in which they were locked at the top of the function.

Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
17 years ago[PATCH] libertas: fix debug enter/leave prints for libertas_execute_next_command
Dan Williams [Fri, 25 May 2007 21:29:34 +0000 (17:29 -0400)]
[PATCH] libertas: fix debug enter/leave prints for libertas_execute_next_command

Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
17 years ago[PATCH] libertas: use compare_ether_addr() rather than memcmp() where appropriate
Dan Williams [Fri, 25 May 2007 21:28:30 +0000 (17:28 -0400)]
[PATCH] libertas: use compare_ether_addr() rather than memcmp() where appropriate

Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
17 years ago[PATCH] libertas: use MAC_FMT and MAC_ARG where appropriate
Dan Williams [Fri, 25 May 2007 21:27:31 +0000 (17:27 -0400)]
[PATCH] libertas: use MAC_FMT and MAC_ARG where appropriate

Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
17 years ago[PATCH] libertas: make association paths consistent
Dan Williams [Fri, 25 May 2007 21:09:41 +0000 (17:09 -0400)]
[PATCH] libertas: make association paths consistent

The BSS to associate with (in either Infrastructure or IBSS join
operations) is now stored in _one_ place in the association request (the
bss member), not two places as before (pattemptedbss and
curbssparams->bssdescriptor).

Association requests are passed to the necessary association functions
to (a) give them access to the bss member and (b) ensure that
association/join/start setup uses settings from the request, not the
current adapter settings (which may not be valid for the requested
settings).

Because the 'bss' member of the association request is used now, the
command return functions from associate and adhoc join/start need access
to the in-progress association request to update curbssparams when
everything is done.  The association worker moves the request from
pending to in-progress for the duration of the association attempt.

Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
17 years ago[PATCH] libertas: move channel changing into association framework
Dan Williams [Fri, 25 May 2007 20:46:33 +0000 (16:46 -0400)]
[PATCH] libertas: move channel changing into association framework

Handle channel changes through the deferred association framework
rather than directly.  Fixes errors when setting channels along
with other parameters like mode and SSID.

Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
17 years ago[PATCH] libertas: fix oops on rmmod
Marcelo Tosatti [Fri, 25 May 2007 20:28:20 +0000 (16:28 -0400)]
[PATCH] libertas: fix oops on rmmod

Use list_for_each_entry_safe, to protect against list_del().

Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
17 years ago[PATCH] libertas: cleanup of fwt_list_route processing
Luis Carlos Cobo Rus [Fri, 25 May 2007 20:26:47 +0000 (16:26 -0400)]
[PATCH] libertas: cleanup of fwt_list_route processing

Signed-off-by: Luis Carlos Cobo Rus <luisca@cozybit.com>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
17 years ago[PATCH] libertas: fix 'keep previous scan' behavior
Dan Williams [Fri, 25 May 2007 20:25:21 +0000 (16:25 -0400)]
[PATCH] libertas: fix 'keep previous scan' behavior

Do not clear the scan list except under specific conditions, such as
when (a) user-requested, or (b) joining/starting an adhoc network.
Furthermore, only clear entries which match the SSID or BSSID of the
request, not the whole scan list.

Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
17 years ago[PATCH] libertas: make scan result handling more flexible
Dan Williams [Fri, 25 May 2007 20:15:56 +0000 (16:15 -0400)]
[PATCH] libertas: make scan result handling more flexible

- use a linked list for scan results
- age scan results
- pass bss_descriptors around instead of indexes into the scan table
- lock access to the scan results
- stop returning EAGAIN from SIOCGIWSCAN handler

Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
17 years ago[PATCH] libertas: updated mesh commands for 5.220.9.p11
Luis Carlos Cobo [Fri, 25 May 2007 17:53:26 +0000 (13:53 -0400)]
[PATCH] libertas: updated mesh commands for 5.220.9.p11

Updated commands fwt_add and fwt_list, bt_list.
New commands: bt_get_invert, bt_set_invert, to invert the blinding table,
i.e., receive only frames from nodes listed in the BT.

This patch needs/is needed for firmware 5.220.9.p11.

Signed-off-by: Luis Carlos Cobo <luisca@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
17 years ago[PATCH] libertas: version bump (321p0) and cmds update for new fw (5.220.10.p0)
Luis Carlos Cobo Rus [Fri, 25 May 2007 17:48:54 +0000 (13:48 -0400)]
[PATCH] libertas: version bump (321p0) and cmds update for new fw (5.220.10.p0)

This patch along with the previous commands update one, is necessary for
mesh and fwt ioctls to work properly with firmware version 5.220.10.p0
and later.

Signed-off-by: Luis Carlos Cobo Rus <luiscarlos@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
17 years ago[PATCH] libertas: don't tear down netdev in libertas_activate_card
Dan Williams [Fri, 25 May 2007 17:36:57 +0000 (13:36 -0400)]
[PATCH] libertas: don't tear down netdev in libertas_activate_card

libertas_activate_card() doesn't create the netdev, and shouldn't
free it on error.  The caller of libertas_activate_card() is
responsible for cleaning up errors from libertas_add_card(),
not libertas_activate_card().

Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
17 years ago[PATCH] libertas: correctly unregister mesh netdev on error
Dan Williams [Fri, 25 May 2007 17:35:23 +0000 (13:35 -0400)]
[PATCH] libertas: correctly unregister mesh netdev on error

Subject says it all.

Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
17 years ago[PATCH] libertas: replace 'macaddress' with 'bssid'
Dan Williams [Fri, 25 May 2007 17:16:38 +0000 (13:16 -0400)]
[PATCH] libertas: replace 'macaddress' with 'bssid'

Start to normalize bss_descriptor with ieee80211_network so we can
eventually replace bss_descriptor more easily.

Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
17 years ago[PATCH] libertas: call SET_NETDEV_DEV from common code
Dan Williams [Fri, 25 May 2007 17:13:25 +0000 (13:13 -0400)]
[PATCH] libertas: call SET_NETDEV_DEV from common code

Move usage of SET_NETDEV_DEV into common code since it has nothing
to do with bus-specific devices.  Also fixes a bug where the mesh
device was getting SET_NETDEV_DEV called after register_netdevice,
resulting in no 'device' link in /sys/class/net/mshX/.

Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
17 years ago[PATCH] libertas: fixed kernel oops on module/card removal
Luis Carlos Cobo [Fri, 25 May 2007 17:11:13 +0000 (13:11 -0400)]
[PATCH] libertas: fixed kernel oops on module/card removal

Fixed kernel oops on module/card removal (using dongles)

Signed-off-by: Luis Carlos Cobo <luisca@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
17 years ago[PATCH] libertas: add URB debug info
Luis Carlos Cobo [Fri, 25 May 2007 17:10:18 +0000 (13:10 -0400)]
[PATCH] libertas: add URB debug info

Signed-off-by: Luis Carlos Cobo <luisca@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
17 years ago[PATCH] libertas: fixed incorrect assigment of fcs errors to frag errors
Luis Carlos Cobo [Fri, 25 May 2007 17:08:33 +0000 (13:08 -0400)]
[PATCH] libertas: fixed incorrect assigment of fcs errors to frag errors

Signed-off-by: Luis Carlos Cobo <luisca@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
17 years ago[PATCH] libertas: remove unused variables in wlan_dev_t
Holger Schurig [Fri, 25 May 2007 17:05:16 +0000 (13:05 -0400)]
[PATCH] libertas: remove unused variables in wlan_dev_t

Actually, this patch removev wlan_dev_t totally and puts the used variables
of it directly into wlan_private. That reduces one level of indirection and
looks a little bit simpler. It's now "priv->card" and not
"priv->wlan_dev.card" and "priv->dev" instead of "priv->wlan_dev.netdev"

Changed two occurences of "((wlan_private *) dev->priv)->wlan_dev.netdev"
into "dev", because I didn't see the point in doing pointer-ping-pong.

The variables "ioport", "upld_rcv" and "upld_type" where unused. They have
been removed.

Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
17 years ago[PATCH] libertas: let DRV_NAME be overridable
Holger Schurig [Fri, 25 May 2007 16:49:10 +0000 (12:49 -0400)]
[PATCH] libertas: let DRV_NAME be overridable

For now, it's "libertas" by default, but that is overwritten in
if_usb.c/if_bootcmd.c and in if_cs.c.

Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
17 years ago[PATCH] libertas: fix RESET logic at unload time
Holger Schurig [Fri, 25 May 2007 16:41:52 +0000 (12:41 -0400)]
[PATCH] libertas: fix RESET logic at unload time

Previously, we had a fixed array of 5 elements where we remembered all
initialized devices. This has been changed to use a "struct list_head"
organization, which is IMHO cleaner.

Also renamed usb_cardp to cardp, as in the reset of the code.

Renamed reset_device() to if_usb_reset_device() like many other functions.

Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
17 years ago[PATCH] libertas: split module into two (libertas.ko and usb8xxx.ko)
Holger Schurig [Fri, 25 May 2007 16:37:58 +0000 (12:37 -0400)]
[PATCH] libertas: split module into two (libertas.ko and usb8xxx.ko)

* add CONFIG_LIBERTAS to Kconfig
* remove global variable libertas_fw_name, the USB module might want to
    use a different default FW name than the CF module, so libertas_fw_name
    is now local to if_usb.c
* exported some symbols as GPL

Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
17 years ago[PATCH] libertas: move contents of fw.h to decl.h
Holger Schurig [Fri, 25 May 2007 16:18:36 +0000 (12:18 -0400)]
[PATCH] libertas: move contents of fw.h to decl.h

Also removes some useless "extern" declarations from function declaration.

Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
17 years ago[PATCH] libertas: indirect all hardware access via hw_XXXX functions
Holger Schurig [Fri, 25 May 2007 16:17:06 +0000 (12:17 -0400)]
[PATCH] libertas: indirect all hardware access via hw_XXXX functions

This functions makes all libertas_sbi_XXX functions static to the
if_usb.c file and renames them to if_usb_XXXX(). The get called from
other places of the source code via priv->hw_XXXX().

Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
17 years ago[PATCH] libertas: wakeup both mesh and normal wakeup when getting out of scan
Chris Ball [Fri, 25 May 2007 16:13:24 +0000 (12:13 -0400)]
[PATCH] libertas: wakeup both mesh and normal wakeup when getting out of scan

The previous patch wakes up the mesh device *instead* of the wlan device
when coming out of scan. We need to wake up both of them.

Signed-off-by: Chris Ball <cjb@laptop.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
17 years ago[PATCH] libertas: added transmission failures to mesh statistics
Javier Cardona [Fri, 25 May 2007 16:12:06 +0000 (12:12 -0400)]
[PATCH] libertas: added transmission failures to mesh statistics

Added transmission failures to mesh statistics.
Removed whitespace before newlines.

Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
17 years ago[PATCH] libertas: fix error handling of card initialization
Marcelo Tosatti [Fri, 25 May 2007 16:09:13 +0000 (12:09 -0400)]
[PATCH] libertas: fix error handling of card initialization

Subject says it all.

Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
17 years ago[PATCH] libertas: fixed transmission flow control on the mesh interface
Javier Cardona [Fri, 25 May 2007 16:06:56 +0000 (12:06 -0400)]
[PATCH] libertas: fixed transmission flow control on the mesh interface

This patch implements proper transmission flow control on mshX.

Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
17 years ago[PATCH] libertas: split wlan_add_card()
Holger Schurig [Fri, 25 May 2007 16:04:31 +0000 (12:04 -0400)]
[PATCH] libertas: split wlan_add_card()

Split wlan_add_card() into a part that just setups kernel parameters and
into the function libertas_activate_card(), which will implizitly use
hardware functions by the started thread.

This allows us later to do something like this:

priv = libertas_add_card();
priv->hw_command_to_host = if_usb_command_to_host;
priv->hw_xxxx = if_usb_xxxx;
priv->hw_yyyy = if_usb_yyyy;
wlan_activate_card()

and of course the CF driver can set it's own functions.

Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
17 years ago[PATCH] libertas: move reset_device() code main.c to if_usb.c
Holger Schurig [Fri, 25 May 2007 16:01:42 +0000 (12:01 -0400)]
[PATCH] libertas: move reset_device() code main.c to if_usb.c

The reset_device() logic is only needed for USB devices, not for CF
devices.

Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
17 years ago[PATCH] libertas: changed some occurences of kmalloc() + memset(&a,0,sz) to kzalloc()
Holger Schurig [Fri, 25 May 2007 15:58:22 +0000 (11:58 -0400)]
[PATCH] libertas: changed some occurences of kmalloc() + memset(&a,0,sz) to kzalloc()

The subject says it all.

Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
17 years ago[PATCH] libertas: fix SSID output
Holger Schurig [Fri, 25 May 2007 15:56:37 +0000 (11:56 -0400)]
[PATCH] libertas: fix SSID output

* a newline was missing
* changed %32s to '%s', no need to right justify the ESSID

Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
17 years ago[PATCH] libertas: get rid of libertas_sbi_get_priv()
Holger Schurig [Fri, 25 May 2007 15:55:19 +0000 (11:55 -0400)]
[PATCH] libertas: get rid of libertas_sbi_get_priv()

It's not really needed, because we can call wlan_remove_card() with
wlan_private* anyway.

Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
17 years ago[PATCH] libertas: change debug output of libertas_interrupt()
Holger Schurig [Fri, 25 May 2007 15:52:42 +0000 (11:52 -0400)]
[PATCH] libertas: change debug output of libertas_interrupt()

It used to be LBS_DEB_MAIN, now it's LBS_DEB_THREAD

Also fixed a missing ":" in lbs_deb_enter()

Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
17 years ago[PATCH] libertas: single out mesh code
Holger Schurig [Fri, 25 May 2007 15:49:19 +0000 (11:49 -0400)]
[PATCH] libertas: single out mesh code

This patches adds the two functions wlan_add_mesh() and wlan_remove_mesh(),
which are responsible for the mshX interface. In a CF driver with a non-
mesh-aware firmware you can omit the calls to this functions.

Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
17 years ago[PATCH] libertas: tune debug code
Holger Schurig [Fri, 25 May 2007 15:32:07 +0000 (11:32 -0400)]
[PATCH] libertas: tune debug code

* renamed module parameter back to libertas_debug
* change from bit shifts to constants, that way it's easier to look at the
    source and specify the libertas_debug=0xXXXX module parameter
* moved module_param from fw.c to main.c, where it belongs better

Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
17 years ago[PATCH] libertas: make debug configurable
Holger Schurig [Fri, 25 May 2007 15:27:16 +0000 (11:27 -0400)]
[PATCH] libertas: make debug configurable

The debug output of libertas was either not present or it was overwhelming.
This patch adds the possibility to specify a bitmask for the area of
interest. One should then only get the desired output.

Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
17 years ago[PATCH] libertas: exclude non-used code when PROC_DEBUG is not set
Holger Schurig [Fri, 25 May 2007 04:37:28 +0000 (00:37 -0400)]
[PATCH] libertas: exclude non-used code when PROC_DEBUG is not set

This reduces usb8xxx.ko by 951 bytes (text) and 256 bytes (data)
when PROC_DEBUG isn't defined.

Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
17 years ago[PATCH] libertas: fix scanning from associate path
Marcelo Tosatti [Fri, 25 May 2007 04:33:28 +0000 (00:33 -0400)]
[PATCH] libertas: fix scanning from associate path

The previous scan fix did not account for scan paths other than set_scan()
that need to do a full scan at once.

Add a "full_scan" parameter to wlan_scan_networks() to control such
behaviour.

Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
17 years ago[PATCH] libertas: make libertas_wlan_data_rates static
Holger Schurig [Fri, 25 May 2007 04:14:38 +0000 (00:14 -0400)]
[PATCH] libertas: make libertas_wlan_data_rates static

Move libertas_wlan_data_rates into wext.c and make it static. wext.c is the
only user of this array.

Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
17 years ago[PATCH] libertas: move vendor & product id's into if_usb.c
Holger Schurig [Fri, 25 May 2007 04:11:58 +0000 (00:11 -0400)]
[PATCH] libertas: move vendor & product id's into if_usb.c

For me it looks cleaner, because it removes one level of indirection.

Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
17 years ago[PATCH] libertas: remove unused/superfluous definitions of DEV_NAME_LEN
Holger Schurig [Fri, 25 May 2007 04:09:54 +0000 (00:09 -0400)]
[PATCH] libertas: remove unused/superfluous definitions of DEV_NAME_LEN

DEV_NAME_LEN is already defined in defs.h and that is sufficient.

Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
17 years ago[PATCH] libertas: remove __FILE__ from debug output
Holger Schurig [Fri, 25 May 2007 04:07:38 +0000 (00:07 -0400)]
[PATCH] libertas: remove __FILE__ from debug output

Remove filename from debug output because it's way too long.

Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
17 years ago[PATCH] libertas: remove deprecated pm_register and associated code
Marcelo Tosatti [Fri, 25 May 2007 04:04:11 +0000 (00:04 -0400)]
[PATCH] libertas: remove deprecated pm_register and associated code

Subject says it all.

Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
17 years ago[PATCH] libertas: fix removal of all debugfs files
Holger Schurig [Fri, 25 May 2007 03:47:34 +0000 (23:47 -0400)]
[PATCH] libertas: fix removal of all debugfs files

rmmod did not remove /sys/kernel/debug/libertas_wireless/eth1/
subscribed_events/high_snr. After I fixed this, I noticed that
it also didn't remove /sys/kernel/debug/libertas_wireless/eth1
as well.

Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
17 years ago[PATCH] libertas: a debug output was missing a newline
Holger Schurig [Fri, 25 May 2007 03:42:42 +0000 (23:42 -0400)]
[PATCH] libertas: a debug output was missing a newline

Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
17 years ago[PATCH] libertas: rename wlan_association_worker
Holger Schurig [Fri, 25 May 2007 03:41:15 +0000 (23:41 -0400)]
[PATCH] libertas: rename wlan_association_worker

Renames wlan_association_worker into libertas_association_worker

Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
17 years ago[PATCH] libertas: scan two channels per scan command
Marcelo Tosatti [Fri, 25 May 2007 03:37:28 +0000 (23:37 -0400)]
[PATCH] libertas: scan two channels per scan command

Scan two channels per each command on set_scan(), then bail out and let
get_scan() continue the scanning work up to the last channel.

This gives time to the firmware so it can go back to the association
channel and keep the connection alive.

Fixes http://dev.laptop.org/ticket/841

Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>