powerpc/mm: Flush cache on memory hot(un)plug

commit fb5924fddf9ee31db04da7ad4e8c3434a387101b upstream.

This patch adds support for flushing potentially dirty cache lines
when memory is hot-plugged/hot-un-plugged. The support is currently
limited to 64 bit systems.

The bug was exposed when mappings for a device were actually
hot-unplugged and plugged in back later. A similar issue was observed
during the development of memtrace, but memtrace does it's own
flushing of region via a custom routine.

These patches do a flush both on hotplug/unplug to clear any stale
data in the cache w.r.t mappings, there is a small race window where a
clean cache line may be created again just prior to tearing down the
mapping.

The patches were tested by disabling the flush routines in memtrace
and doing I/O on the trace file. The system immediately
checkstops (quite reliablly if prior to the hot-unplug of the memtrace
region, we memset the regions we are about to hot unplug). After these
patches no custom flushing is needed in the memtrace code.

Fixes: 9d5171a8f248 ("powerpc/powernv: Enable removal of memory for in memory tracing")
Cc: stable@vger.kernel.org # v4.14+
Signed-off-by: Balbir Singh <bsingharora@gmail.com>
Acked-by: Reza Arbab <arbab@linux.ibm.com>
Reviewed-by: Rashmica Gupta <rashmica.g@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

KVM: arm/arm64: Close VMID generation race

commit f0cf47d939d0b4b4f660c5aaa4276fa3488f3391 upstream.

Before entering the guest, we check whether our VMID is still
part of the current generation. In order to avoid taking a lock,
we start with checking that the generation is still current, and
only if not current do we take the lock, recheck, and update the
generation and VMID.

This leaves open a small race: A vcpu can bump up the global
generation number as well as the VM's, but has not updated
the VMID itself yet.

At that point another vcpu from the same VM comes in, checks
the generation (and finds it not needing anything), and jumps
into the guest. At this point, we end-up with two vcpus belonging
to the same VM running with two different VMIDs. Eventually, the
VMID used by the second vcpu will get reassigned, and things will
really go wrong...

A simple solution would be to drop this initial check, and always take
the lock. This is likely to cause performance issues. A middle ground
is to convert the spinlock to a rwlock, and only take the read lock
on the fast path. If the check fails at that point, drop it and
acquire the write lock, rechecking the condition.

This ensures that the above scenario doesn't occur.

Cc: stable@vger.kernel.org
Reported-by: Mark Rutland <mark.rutland@arm.com>
Tested-by: Shannon Zhao <zhaoshenglong@huawei.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ARM: socfpga_defconfig: Remove QSPI Sector 4K size force

commit 6e8fe39989720b87439fee7817a5ca362b16d931 upstream.

Remove QSPI Sector 4K size force which is causing QSPI boot
problems with the JFFS2 root filesystem.

Fixes the following error:
     "Magic bitmask 0x1985 not found at ..."

Cc: stable@vger.kernel.org
Signed-off-by: Thor Thayer <thor.thayer@linux.intel.com>
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ARM: amba: Don't read past the end of sysfs "driver_override" buffer

commit d2ffed5185df9d8d9ccd150e4340e3b6f96a8381 upstream.

When printing the driver_override parameter when it is 4095 and 4094
bytes long, the printing code would access invalid memory because we
need count + 1 bytes for printing.

Cfr. commits 4efe874aace57dba ("PCI: Don't read past the end of sysfs
"driver_override" buffer") and bf563b01c2895a4b ("driver core: platform:
Don't read past the end of "driver_override" buffer").

Fixes: 3cf385713460eb2b ("ARM: 8256/1: driver coamba: add device binding path 'driver_override'")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Todd Kjos <tkjos@google.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ARM: amba: Fix race condition with driver_override

commit 6a7228d90d42bcacfe38786756ba62762b91c20a upstream.

The driver_override implementation is susceptible to a race condition
when different threads are reading vs storing a different driver
override.  Add locking to avoid this race condition.

Cfr. commits 6265539776a0810b ("driver core: platform: fix race
condition with driver_override") and 9561475db680f714 ("PCI: Fix race
condition with driver_override").

Fixes: 3cf385713460eb2b ("ARM: 8256/1: driver coamba: add device binding path 'driver_override'")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Todd Kjos <tkjos@google.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ARM: amba: Make driver_override output consistent with other buses

commit 5f53624662eaac89598641cee6cd54fc192572d9 upstream.

For AMBA devices with unconfigured driver override, the
"driver_override" sysfs virtual file is empty, while it contains
"(null)" for platform and PCI devices.

Make AMBA consistent with other buses by dropping the test for a NULL
pointer.

Note that contrary to popular belief, sprintf() handles NULL pointers
fine; they are printed as "(null)".

Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Cc: stable <stable@vger.kernel.org>
Reviewed-by: Todd Kjos <tkjos@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

PCI: aardvark: Fix PCIe Max Read Request Size setting

commit fc31c4e347c9dad50544d01d5ee98b22c7df88bb upstream.

There is an obvious typo issue in the definition of the PCIe maximum
read request size: a bit shift is directly used as a value, while it
should be used to shift the correct value.

Fixes: 8c39d710363c1 ("PCI: aardvark: Add Aardvark PCI host controller driver")
Cc: <stable@vger.kernel.org>
Signed-off-by: Evan Wang <xswang@marvell.com>
Reviewed-by: Victor Gu <xigu@marvell.com>
Reviewed-by: Nadav Haklai <nadavh@marvell.com>
[Thomas: tweak commit log.]
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

PCI: aardvark: Use ISR1 instead of ISR0 interrupt in legacy irq mode

commit 3430f924a62905891c8fa9a3b97ea52007795bc3 upstream.

The Aardvark has two interrupts sets:

 - first set is bit[23:16] of PCIe ISR 0 register(RD0074840h)

 - second set is bit[11:8] of PCIe ISR 1 register(RD0074848h)

Only one set should be used, while another set should be masked.

The second set, ISR1, is more advanced, the Legacy INT_X status bit is
asserted once Assert_INTX message is received, and de-asserted after
Deassert_INTX message is received which matches what the driver is
currently doing in the ->irq_mask() and ->irq_unmask() functions.

The ISR0 requires additional work to deassert the interrupt, which the
driver does not currently implement, therefore it needs fixing.

Update the driver to use ISR1 register set, fixing current
implementation.

Fixes: 8c39d710363c1 ("PCI: aardvark: Add Aardvark PCI host controller driver")
Link: https://bugzilla.kernel.org/show_bug.cgi?id=196339
Signed-off-by: Victor Gu <xigu@marvell.com>
[Thomas: tweak commit log.]
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
[lorenzo.pieralisi@arm.com: updated the commit log]
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Evan Wang <xswang@marvell.com>
Reviewed-by: Nadav Haklai <nadavh@marvell.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

PCI: aardvark: Set PIO_ADDR_LS correctly in advk_pcie_rd_conf()

commit 4fa3999ee672c54a5498ce98e20fe3fdf9c1cbb4 upstream.

When setting the PIO_ADDR_LS register during a configuration read, we
were properly passing the device number, function number and register
number, but not the bus number, causing issues when reading the
configuration of PCIe devices.

Fixes: 8c39d710363c1 ("PCI: aardvark: Add Aardvark PCI host controller driver")
Cc: <stable@vger.kernel.org>
Signed-off-by: Victor Gu <xigu@marvell.com>
Reviewed-by: Wilson Ding <dingwei@marvell.com>
Reviewed-by: Nadav Haklai <nadavh@marvell.com>
[Thomas: tweak commit log.]
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

PCI: aardvark: Fix logic in advk_pcie_{rd,wr}_conf()

commit 660661afcd40ed7f515ef3369721ed58e80c0fc5 upstream.

The PCI configuration space read/write functions were special casing
the situation where PCI_SLOT(devfn) != 0, and returned
PCIBIOS_DEVICE_NOT_FOUND in this case.

However, while this is what is intended for the root bus, it is not
intended for the child busses, as it prevents discovering devices with
PCI_SLOT(x) != 0. Therefore, we return PCIBIOS_DEVICE_NOT_FOUND only
if we're on the root bus.

Fixes: 8c39d710363c1 ("PCI: aardvark: Add Aardvark PCI host controller driver")
Cc: <stable@vger.kernel.org>
Signed-off-by: Victor Gu <xigu@marvell.com>
Reviewed-by: Wilson Ding <dingwei@marvell.com>
Reviewed-by: Nadav Haklai <nadavh@marvell.com>
[Thomas: tweak commit log.]
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ANDROID: binder: prevent transactions into own process.

commit 7aa135fcf26377f92dc0680a57566b4c7f3e281b upstream.

This can't happen with normal nodes (because you can't get a ref
to a node you own), but it could happen with the context manager;
to make the behavior consistent with regular nodes, reject
transactions into the context manager by the process owning it.

Reported-by: syzbot+09e05aba06723a94d43d@syzkaller.appspotmail.com
Signed-off-by: Martijn Coenen <maco@android.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

vfio: ccw: process ssch with interrupts disabled

commit 3368e547c52b96586f0edf9657ca12b94d8e61a7 upstream.

When we call ssch, an interrupt might already be pending once we
return from the START SUBCHANNEL instruction. Therefore we need to
make sure interrupts are disabled while holding the subchannel lock
until after we're done with our processing.

Cc: stable@vger.kernel.org #v4.12+
Reviewed-by: Dong Jia Shi <bjsdjshi@linux.ibm.com>
Acked-by: Halil Pasic <pasic@linux.vnet.ibm.com>
Acked-by: Pierre Morel <pmorel@linux.vnet.ibm.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

bfq-iosched: ensure to clear bic/bfqq pointers when preparing request

commit 72961c4e6082be79825265d9193272b8a1634dec upstream.

Even if we don't have an IO context attached to a request, we still
need to clear the priv[0..1] pointers, as they could be pointing
to previously used bic/bfqq structures. If we don't do so, we'll
either corrupt memory on dispatching a request, or cause an
imbalance in counters.

Inspired by a fix from Kees.

Reported-by: Oleksandr Natalenko <oleksandr@natalenko.name>
Reported-by: Kees Cook <keescook@chromium.org>
Cc: stable@vger.kernel.org
Fixes: aee69d78dec0 ("block, bfq: introduce the BFQ-v0 I/O scheduler as an extra scheduler")
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

scsi: sd: Defer spinning up drive while SANITIZE is in progress

commit 505aa4b6a8834a2300971c5220c380c3271ebde3 upstream.

A drive being sanitized will return NOT READY / ASC 0x4 / ASCQ
0x1b ("LOGICAL UNIT NOT READY. SANITIZE IN PROGRESS").

Prevent spinning up the drive until this condition clears.

[mkp: tweaked commit message]

Signed-off-by: Mahesh Rajashekhara <mahesh.rajashekhara@microsemi.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

kobject: don't use WARN for registration failures

commit 3e14c6abbfb5c94506edda9d8e2c145d79375798 upstream.

This WARNING proved to be noisy. The function still returns an error
and callers should handle it. That's how most of kernel code works.
Downgrade the WARNING to pr_err() and leave WARNINGs for kernel bugs.

Signed-off-by: Dmitry Vyukov <dvyukov@google.com>
Reported-by: syzbot+209c0f67f99fec8eb14b@syzkaller.appspotmail.com
Reported-by: syzbot+7fb6d9525a4528104e05@syzkaller.appspotmail.com
Reported-by: syzbot+2e63711063e2d8f9ea27@syzkaller.appspotmail.com
Reported-by: syzbot+de73361ee4971b6e6f75@syzkaller.appspotmail.com
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

mtd: rawnand: tango: Fix struct clk memory leak

commit 007b4e8b705a4eff184d567c5a8b496622f9e116 upstream.

Use devm_clk_get() to let Linux manage struct clk memory.

Fixes: 6956e2385a16 ("add tango NAND flash controller support")
Cc: stable@vger.kernel.org
Reported-by: Xidong Wang <wangxidong_97@163.com>
Signed-off-by: Marc Gonzalez <marc_gonzalez@sigmadesigns.com>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

mtd: cfi: cmdset_0002: Do not allow read/write to suspend erase block.

commit 7b70eb14392a7cf505f9b358d06c33b5af73d1e7 upstream.

Currently it is possible to read and/or write to suspend EB's.
Writing /dev/mtdX or /dev/mtdblockX from several processes may
break the flash state machine.

Taken from cfi_cmdset_0001 driver.

Signed-off-by: Joakim Tjernlund <joakim.tjernlund@infinera.com>
Cc: <stable@vger.kernel.org>
Reviewed-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

mtd: cfi: cmdset_0001: Workaround Micron Erase suspend bug.

commit 46a16a2283f9e678a4e26829175e0c37a5191860 upstream.

Some Micron chips does not work well wrt Erase suspend for
boot blocks. This avoids the issue by not allowing Erase suspend
for the boot blocks for the 28F00AP30(1GBit) chip.

Signed-off-by: Joakim Tjernlund <joakim.tjernlund@infinera.com>
Cc: <stable@vger.kernel.org>
Reviewed-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

mtd: cfi: cmdset_0001: Do not allow read/write to suspend erase block.

commit 6510bbc88e3258631831ade49033537081950605 upstream.

Currently it is possible to read and/or write to suspend EB's.
Writing /dev/mtdX or /dev/mtdblockX from several processes may
break the flash state machine.

Signed-off-by: Joakim Tjernlund <joakim.tjernlund@infinera.com>
Cc: <stable@vger.kernel.org>
Reviewed-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

mtd: spi-nor: cadence-quadspi: Fix page fault kernel panic

commit 47016b341fc3b3fd4909e058c6fa38f165b53646 upstream.

The current Cadence QSPI driver caused a kernel panic when loading
a Root Filesystem from QSPI. The problem was caused by reading more
bytes than needed because the QSPI operated on 4 bytes at a time.
<snip>
[    7.947754] spi_nor_read[1048]:from 0x037cad74, len 1 [bfe07fff]
[    7.956247] cqspi_read[910]:offset 0x58502516, buffer=bfe07fff
[    7.956247]
[    7.966046] Unable to handle kernel paging request at virtual
address bfe08002
[    7.973239] pgd = eebfc000
[    7.975931] [bfe08002] *pgd=2fffb811, *pte=00000000, *ppte=00000000
</snip>
Notice above how only 1 byte needed to be read but by reading 4 bytes
into the end of a mapped page, an unrecoverable page fault occurred.

This patch uses a temporary buffer to hold the 4 bytes read and then
copies only the bytes required into the buffer. A min() function is
used to limit the length to prevent buffer overflows.

Request testing of this patch on other platforms. This was tested
on the Intel Arria10 SoCFPGA DevKit.

Fixes: 0cf1725676a97fc8 ("mtd: spi-nor: cqspi: Fix build on arches missing readsl/writesl")
Signed-off-by: Thor Thayer <thor.thayer@linux.intel.com>
Cc: <stable@vger.kernel.org>
Reviewed-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ALSA: hda/realtek - change the location for one of two front mics

commit 65811834ba56e9ed88117cf6c09880416c9951ab upstream.

On this Lenovo ThinkCentre machine. There are two front mics,
we change the location for one of them.

Relation: f33f79f3d0e5 ("ALSA: hda/realtek - change the location for
one of two front microphones")

Signed-off-by: Kailang Yang <kailang@realtek.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ALSA: hda/realtek - Update ALC255 depop optimize

commit ab3b8e5159b5335c81ba2d09ee5054d4a1b5a7a6 upstream.

Add ALC255 its own depop functions for alc_init and alc_shutup.
Assign it to ALC256 usage.

Signed-off-by: Kailang Yang <kailang@realtek.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ALSA: hda/realtek - Add some fixes for ALC233

commit ea04a1dbf8b1d6af759d58e705636fde48583f8f upstream.

Fill COEF to change EAPD to verb control.
Assigned codec type.

This is an additional fix over 92f974df3460 ("ALSA: hda/realtek - New
vendor ID for ALC233").

[ More notes:
  according to Kailang, the chip is 10ec:0235 bonding for ALC233b,
  which is equivalent with ALC255.  It's only used for Lenovo.
  The chip needs no alc_process_coef_fw() for headset unlike ALC255. ]

Signed-off-by: Kailang Yang <kailang@realtek.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ALSA: hda: Hardening for potential Spectre v1

commit 69fa6f19b95597618ab30438a27b67ad93daa7c7 upstream.

As recently Smatch suggested, one place in HD-audio hwdep ioctl codes
may expand the array directly from the user-space value with
speculation:
  sound/pci/hda/hda_local.h:467 get_wcaps() warn: potential spectre issue 'codec->wcaps'

As get_wcaps() itself is a fairly frequently called inline function,
and there is only one single call with a user-space value, we replace
only the latter one to open-code locally with array_index_nospec()
hardening in this patch.

BugLink: https://marc.info/?l=linux-kernel&m=152411496503418&w=2
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ALSA: seq: oss: Hardening for potential Spectre v1

commit 8d218dd8116695ecda7164f97631c069938aa22e upstream.

As Smatch recently suggested, a few places in OSS sequencer codes may
expand the array directly from the user-space value with speculation,
namely there are a significant amount of references to either
info->ch[] or dp->synths[] array:

  sound/core/seq/oss/seq_oss_event.c:315 note_on_event() warn: potential spectre issue 'info->ch' (local cap)
  sound/core/seq/oss/seq_oss_event.c:362 note_off_event() warn: potential spectre issue 'info->ch' (local cap)
  sound/core/seq/oss/seq_oss_synth.c:470 snd_seq_oss_synth_load_patch() warn: potential spectre issue 'dp->synths' (local cap)
  sound/core/seq/oss/seq_oss_event.c:293 note_on_event() warn: potential spectre issue 'dp->synths'
  sound/core/seq/oss/seq_oss_event.c:353 note_off_event() warn: potential spectre issue 'dp->synths'
  sound/core/seq/oss/seq_oss_synth.c:506 snd_seq_oss_synth_sysex() warn: potential spectre issue 'dp->synths'
  sound/core/seq/oss/seq_oss_synth.c:580 snd_seq_oss_synth_ioctl() warn: potential spectre issue 'dp->synths'

Although all these seem doing only the first load without further
reference, we may want to stay in a safer side, so hardening with
array_index_nospec() would still make sense.

We may put array_index_nospec() at each place, but here we take a
different approach:

- For dp->synths[], change the helpers to retrieve seq_oss_synthinfo
  pointer directly instead of the array expansion at each place

- For info->ch[], harden in a normal way, as there are only a couple
  of places

As a result, the existing helper, snd_seq_oss_synth_is_valid() is
replaced with snd_seq_oss_synth_info().  Also, we cover MIDI device
where a similar array expansion is done, too, although it wasn't
reported by Smatch.

BugLink: https://marc.info/?l=linux-kernel&m=152411496503418&w=2
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ALSA: seq: oss: Fix unbalanced use lock for synth MIDI device

commit f5e94b4c6ebdabe0f602d796e0430180927521a0 upstream.

When get_synthdev() is called for a MIDI device, it returns the fixed
midi_synth_dev without the use refcounting.  OTOH, the caller is
supposed to unreference unconditionally after the usage, so this would
lead to unbalanced refcount.

This patch corrects the behavior and keep up the refcount balance also
for the MIDI synth device.

Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ALSA: core: Report audio_tstamp in snd_pcm_sync_ptr

commit f853dcaae2f5bbe021161e421bd1576845bae8f6 upstream.

It looks like a simple mistake that this struct member
was forgotten.

Audio_tstamp isn't used much, and on some archs (such as x86) this
ioctl is not used by default, so that might be the reason why this
has slipped for so long.

Fixes: 4eeaaeaea1ce ("ALSA: core: add hooks for audio timestamps")
Signed-off-by: David Henningsson <diwic@ubuntu.com>
Reviewed-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Cc: <stable@vger.kernel.org> # v3.8+
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ALSA: pcm: Return negative delays from SNDRV_PCM_IOCTL_DELAY.

commit 912e4c332037e7ed063c164985c36fb2b549ea3a upstream.

The commit c2c86a97175f ("ALSA: pcm: Remove set_fs() in PCM core code")
changed SNDRV_PCM_IOCTL_DELAY to return an inconsistent error instead of a
negative delay.  Originally the call would succeed and return the negative
delay.  The Chromium OS Audio Server (CRAS) gets confused and hangs when
the error is returned instead of the negative delay.

Help CRAS avoid the issue by rolling back the behavior to return a
negative delay instead of an error.

Fixes: c2c86a97175f ("ALSA: pcm: Remove set_fs() in PCM core code")
Signed-off-by: Jeffery Miller <jmiller@neverware.com>
Cc: <stable@vger.kernel.org> # v4.13+
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ALSA: control: Hardening for potential Spectre v1

commit 088e861edffb84879cf0c0d1b02eda078c3a0ffe upstream.

As recently Smatch suggested, a few places in ALSA control core codes
may expand the array directly from the user-space value with
speculation:

  sound/core/control.c:1003 snd_ctl_elem_lock() warn: potential spectre issue 'kctl->vd'
  sound/core/control.c:1031 snd_ctl_elem_unlock() warn: potential spectre issue 'kctl->vd'
  sound/core/control.c:844 snd_ctl_elem_info() warn: potential spectre issue 'kctl->vd'
  sound/core/control.c:891 snd_ctl_elem_read() warn: potential spectre issue 'kctl->vd'
  sound/core/control.c:939 snd_ctl_elem_write() warn: potential spectre issue 'kctl->vd'

Although all these seem doing only the first load without further
reference, we may want to stay in a safer side, so hardening with
array_index_nospec() would still make sense.

In this patch, we put array_index_nospec() to the common
snd_ctl_get_ioff*() helpers instead of each caller.  These helpers are
also referred from some drivers, too, and basically all usages are to
calculate the array index from the user-space value, hence it's better
to cover there.

BugLink: https://marc.info/?l=linux-kernel&m=152411496503418&w=2
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ALSA: rme9652: Hardening for potential Spectre v1

commit f526afcd8f71945c23ce581d7864ace93de8a4f7 upstream.

As recently Smatch suggested, one place in RME9652 driver may expand
the array directly from the user-space value with speculation:
  sound/pci/rme9652/rme9652.c:2074 snd_rme9652_channel_info() warn: potential spectre issue 'rme9652->channel_map' (local cap)

This patch puts array_index_nospec() for hardening against it.

BugLink: https://marc.info/?l=linux-kernel&m=152411496503418&w=2
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ALSA: hdspm: Hardening for potential Spectre v1

commit 10513142a7114d251670361ad40cba2c61403406 upstream.

As recently Smatch suggested, a couple of places in HDSP MADI driver
may expand the array directly from the user-space value with
speculation:
  sound/pci/rme9652/hdspm.c:5717 snd_hdspm_channel_info() warn: potential spectre issue 'hdspm->channel_map_out' (local cap)
  sound/pci/rme9652/hdspm.c:5734 snd_hdspm_channel_info() warn: potential spectre issue 'hdspm->channel_map_in' (local cap)

This patch puts array_index_nospec() for hardening against them.

BugLink: https://marc.info/?l=linux-kernel&m=152411496503418&w=2
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ALSA: asihpi: Hardening for potential Spectre v1

commit f9d94b57e30fd1575b4935045b32d738668aa74b upstream.

As recently Smatch suggested, a couple of places in ASIHPI driver may
expand the array directly from the user-space value with speculation:
  sound/pci/asihpi/hpimsginit.c:70 hpi_init_response() warn: potential spectre issue 'res_size' (local cap)
  sound/pci/asihpi/hpioctl.c:189 asihpi_hpi_ioctl() warn: potential spectre issue 'adapters'

This patch puts array_index_nospec() for hardening against them.

BugLink: https://marc.info/?l=linux-kernel&m=152411496503418&w=2
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ALSA: opl3: Hardening for potential Spectre v1

commit 7f054a5bee0987f1e2d4e59daea462421c76f2cb upstream.

As recently Smatch suggested, one place in OPL3 driver may expand the
array directly from the user-space value with speculation:
  sound/drivers/opl3/opl3_synth.c:476 snd_opl3_set_voice() warn: potential spectre issue 'snd_opl3_regmap'

This patch puts array_index_nospec() for hardening against it.

BugLink: https://marc.info/?l=linux-kernel&m=152411496503418&w=2
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ALSA: hda - Skip jack and others for non-existing PCM streams

commit 8a7d6003df41cb16f6b3b620da044fbd92d2f5ee upstream.

When CONFIG_SND_DYNAMIC_MINORS isn't set, there are only limited
number of devices available, and HD-audio, especially with HDMI/DP
codec, will fail to create more than two devices.

The driver warns about the lack of such devices and skips the PCM
device creations, but the HDMI driver still tries to create the
corresponding JACK, SPDIF and ELD controls even for the non-existing
PCM substreams.  This results in confusion on user-space, and even may
break the operation.

Similarly, Intel HDMI/DP codec builds the ELD notification from i915
graphics driver, and this may be broken if a notification is sent for
the non-existing PCM stream.

This patch adds the check of the existence of the assigned PCM
substream in the both scenarios above, and skips the further operation
if the PCM substream is not assigned.

Fixes: 9152085defb6 ("ALSA: hda - add DP MST audio support")
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ALSA: dice: fix error path to destroy initialized stream data

commit 0f925660a7bc49b269c163249a5d06da3a0c7b0a upstream.

In error path of snd_dice_stream_init_duplex(), stream data for incoming
packet can be left to be initialized.

This commit fixes it.

Fixes: 436b5abe2224 ('ALSA: dice: handle whole available isochronous streams')
Cc: <stable@vger.kernel.org> # v4.6+
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ALSA: dice: fix OUI for TC group

commit 10412c420af9ba1f3de8483a95d360e5eb5bfc84 upstream.

OUI for TC Electronic is 0x000166, for TC GROUP A/S. 0x001486 is for Echo
Digital Audio Corporation.

Fixes: 7cafc65b3aa1 ('ALSA: dice: force to add two pcm devices for listed models')
Cc: <stable@vger.kernel.org> # v4.6+
Reference: http://standards-oui.ieee.org/oui/oui.txt
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

tty: Use __GFP_NOFAIL for tty_ldisc_get()

commit bcdd0ca8cb8730573afebcaae4138f8f4c8eaa20 upstream.

syzbot is reporting crashes triggered by memory allocation fault injection
at tty_ldisc_get() [1]. As an attempt to handle OOM in a graceful way, we
have tried commit 5362544bebe85071 ("tty: don't panic on OOM in
tty_set_ldisc()"). But we reverted that attempt by commit a8983d01f9b7d600
("Revert "tty: don't panic on OOM in tty_set_ldisc()"") due to reproducible
crash. We should spend resource for finding and fixing race condition bugs
rather than complicate error paths for 2 * sizeof(void *) bytes allocation
failure.

[1] https://syzkaller.appspot.com/bug?id=489d33fa386453859ead58ff5171d43772b13aa3

Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Reported-by: syzbot <syzbot+40b7287c2dc987c48c81@syzkaller.appspotmail.com>
Cc: Michal Hocko <mhocko@suse.com>
Cc: Vegard Nossum <vegard.nossum@gmail.com>
Cc: Dmitry Vyukov <dvyukov@google.com>
Cc: Jiri Slaby <jslaby@suse.com>
Cc: Peter Hurley <peter@hurleysoftware.com>
Cc: One Thousand Gnomes <gnomes@lxorguk.ukuu.org.uk>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

tty: Avoid possible error pointer dereference at tty_ldisc_restore().

commit 598c2d41ff44889dd8eced4f117403e472158d85 upstream.

syzbot is reporting crashes [1] triggered by memory allocation failure at
tty_ldisc_get() from tty_ldisc_restore(). While syzbot stops at WARN_ON()
due to panic_on_warn == true, panic_on_warn == false will after all trigger
an OOPS by dereferencing old->ops->num if IS_ERR(old) == true.

We can simplify tty_ldisc_restore() as three calls (old->ops->num, N_TTY,
N_NULL) to tty_ldisc_failto() in addition to avoiding possible error
pointer dereference.

If someone reports kernel panic triggered by forcing all memory allocations
for tty_ldisc_restore() to fail, we can consider adding __GFP_NOFAIL for
tty_ldisc_restore() case.

[1] https://syzkaller.appspot.com/bug?id=6ac359c61e71d22e06db7f8f88243feb11d927e7

Reported-by: syzbot+40b7287c2dc987c48c81@syzkaller.appspotmail.com
Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jslaby@suse.com>
Cc: Dmitry Vyukov <dvyukov@google.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Alan Cox <alan@llwyncelyn.cymru>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Michal Hocko <mhocko@suse.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

tty: n_gsm: Fix DLCI handling for ADM mode if debug & 2 is not set

commit b2d89ad9c9682e795ed6eeb9ed455789ad6cedf1 upstream.

At least on droid 4 with control channel in ADM mode, there is no response
to Modem Status Command (MSC). Currently gsmtty_modem_update() expects to
have data in dlci->modem_rx unless debug & 2 is set. This means that on
droid 4, things only work if debug & 2 is set.

Let's fix the issue by ignoring empty dlci->modem_rx for ADM mode. In
the AMD mode, CMD_MSC will never respond and gsm_process_modem() won't
get called to set dlci->modem_rx.

And according to ts_127010v140000p.pdf, MSC is only relevant if basic
option is chosen, so let's test for that too.

Fixes: ea3d8465ab9b ("tty: n_gsm: Allow ADM response in addition to UA for control dlci")
Cc: linux-serial@vger.kernel.org
Cc: Alan Cox <alan@llwyncelyn.cymru>
Cc: Dan Williams <dcbw@redhat.com>
Cc: Jiri Prchal <jiri.prchal@aksignal.cz>
Cc: Jiri Slaby <jslaby@suse.cz>
Cc: Marcel Partap <mpartap@gmx.net>
Cc: Merlijn Wajer <merlijn@wizzup.org>
Cc: Michael Nazzareno Trimarchi <michael@amarulasolutions.com>
Cc: Michael Scott <michael.scott@linaro.org>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Peter Hurley <peter@hurleysoftware.com>
Cc: Russ Gorby <russ.gorby@intel.com>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

tty: n_gsm: Fix long delays with control frame timeouts in ADM mode

commit e9ec22547986dd32c5c70da78107ce35dbff1344 upstream.

Commit ea3d8465ab9b ("tty: n_gsm: Allow ADM response in addition to UA for
control dlci") added support for DLCI to stay in Asynchronous Disconnected
Mode (ADM). But we still get long delays waiting for commands to other
DLCI to complete:

--> 5) C: SABM(P)
Q>  0) C: UIH(F)
Q>  0) C: UIH(F)
Q>  0) C: UIH(F)
...

This happens because gsm_control_send() sets cretries timer to T2 that is
by default set to 34. This will cause resend for T2 times for the control
frame. In ADM mode, we will never get a response so the control frame, so
retries are just delaying all the commands.

Let's fix the issue by setting DLCI_MODE_ADM flag after detecting the ADM
mode for the control DLCI. Then we can use that in gsm_control_send() to
set retries to 1. This means the control frame will be sent once allowing
the other end at an opportunity to switch from ADM to ABM mode.

Note that retries will be decremented in gsm_control_retransmit() so
we don't want to set it to 0 here.

Fixes: ea3d8465ab9b ("tty: n_gsm: Allow ADM response in addition to UA for control dlci")
Cc: linux-serial@vger.kernel.org
Cc: Alan Cox <alan@llwyncelyn.cymru>
Cc: Dan Williams <dcbw@redhat.com>
Cc: Jiri Prchal <jiri.prchal@aksignal.cz>
Cc: Jiri Slaby <jslaby@suse.cz>
Cc: Marcel Partap <mpartap@gmx.net>
Cc: Merlijn Wajer <merlijn@wizzup.org>
Cc: Michael Nazzareno Trimarchi <michael@amarulasolutions.com>
Cc: Michael Scott <michael.scott@linaro.org>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Peter Hurley <peter@hurleysoftware.com>
Cc: Russ Gorby <russ.gorby@intel.com>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

tty: Don't call panic() at tty_ldisc_init()

commit 903f9db10f18f735e62ba447147b6c434b6af003 upstream.

syzbot is reporting kernel panic [1] triggered by memory allocation failure
at tty_ldisc_get() from tty_ldisc_init(). But since both tty_ldisc_get()
and caller of tty_ldisc_init() can cleanly handle errors, tty_ldisc_init()
does not need to call panic() when tty_ldisc_get() failed.

[1] https://syzkaller.appspot.com/bug?id=883431818e036ae6a9981156a64b821110f39187

Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Reported-by: syzbot <syzkaller@googlegroups.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jslaby@suse.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

drm/virtio: fix vq wait_event condition

commit d02d270014f70dcab0117776b81a37b6fca745ae upstream.

Wait until we have enough space in the virt queue to actually queue up
our request.  Avoids the guest spinning in case we have a non-zero
amount of free entries but not enough for the request.

Cc: stable@vger.kernel.org
Reported-by: Alain Magloire <amagloire@blackberry.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Dave Airlie <airlied@redhat.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20180403095904.11152-1-kraxel@redhat.com
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

virtio_console: reset on out of memory

commit 5c60300d68da32ca77f7f978039dc72bfc78b06b upstream.

When out of memory and we can't add ctrl vq buffers,
probe fails. Unfortunately the error handling is
out of spec: it calls del_vqs without bothering
to reset the device first.

To fix, call the full cleanup function in this case.

Cc: stable@vger.kernel.org
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

virtio_console: move removal code

commit aa44ec867030a72e8aa127977e37dec551d8df19 upstream.

Will make it reusable for error handling.

Cc: stable@vger.kernel.org
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

virtio_console: drop custom control queue cleanup

commit 61a8950c5c5708cf2068b29ffde94e454e528208 upstream.

We now cleanup all VQs on device removal - no need
to handle the control VQ specially.

Cc: stable@vger.kernel.org
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

virtio_console: free buffers after reset

commit a7a69ec0d8e4a58be7db88d33cbfa2912807bb2b upstream.

Console driver is out of spec. The spec says:
A driver MUST NOT decrement the available idx on a live
virtqueue (ie. there is no way to “unexpose” buffers).
and it does exactly that by trying to detach unused buffers
without doing a device reset first.

Defer detaching the buffers until device unplug.

Of course this means we might get an interrupt for
a vq without an attached port now. Handle that by
discarding the consumed buffer.

Reported-by: Tiwei Bie <tiwei.bie@intel.com>
Fixes: b3258ff1d6 ("virtio: Decrement avail idx on buffer detach")
Cc: stable@vger.kernel.org
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

virtio_console: don't tie bufs to a vq

commit 2855b33514d290c51d52d94e25d3ef942cd4d578 upstream.

an allocated buffer doesn't need to be tied to a vq -
only vq->vdev is ever used. Pass the function the
just what it needs - the vdev.

Cc: stable@vger.kernel.org
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

virtio: add ability to iterate over vqs

commit 24a7e4d20783c0514850f24a5c41ede46ab058f0 upstream.

For cleanup it's helpful to be able to simply scan all vqs and discard
all data. Add an iterator to do that.

Cc: stable@vger.kernel.org
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ALSA: usb-audio: Skip broken EU on Dell dock USB-audio

commit 1d8d6428d1da642ddd75b0be2d1bb1123ff8e017 upstream.

The Dell Dock USB-audio device with 0bda:4014 is behaving notoriously
bad, and we have already applied some workaround to avoid the firmware
hiccup.  Yet we still need to skip one thing, the Extension Unit at ID
4, which doesn't react correctly to the mixer ctl access.

Bugzilla: https://bugzilla.suse.com/show_bug.cgi?id=1090658
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

USB: Increment wakeup count on remote wakeup.

commit 83a62c51ba7b3c0bf45150c4eac7aefc6c785e94 upstream.

On chromebooks we depend on wakeup count to identify the wakeup source.
But currently USB devices do not increment the wakeup count when they
trigger the remote wake. This patch addresses the same.

Resume condition is reported differently on USB 2.0 and USB 3.0 devices.

On USB 2.0 devices, a wake capable device, if wake enabled, drives
resume signal to indicate a remote wake (USB 2.0 spec section 7.1.7.7).
The upstream facing port then sets C_PORT_SUSPEND bit and reports a
port change event (USB 2.0 spec section 11.24.2.7.2.3). Thus if a port
has resumed before driving the resume signal from the host and
C_PORT_SUSPEND is set, then the device attached to the given port might
be the reason for the last system wakeup. Increment the wakeup count for
the same.

On USB 3.0 devices, a function may signal that it wants to exit from device
suspend by sending a Function Wake Device Notification to the host (USB3.0
spec section 8.5.6.4) Thus on receiving the Function Wake, increment the
wakeup count.

Signed-off-by: Ravi Chandra Sadineni <ravisadineni@chromium.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

usb: core: Add quirk for HP v222w 16GB Mini

commit 3180dabe08e3653bf0a838553905d88f3773f29c upstream.

Add DELAY_INIT quirk to fix the following problem with HP
v222w 16GB Mini:

usb 1-3: unable to read config index 0 descriptor/start: -110
usb 1-3: can't read configurations, error -110
usb 1-3: can't set config #1, error -110

Signed-off-by: Kamil Lulko <kamilx.lulko@intel.com>
Signed-off-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

usb: typec: ucsi: Increase command completion timeout value

commit b1b59e16075f5e5da2943ce8de724ab96bc3c6c2 upstream.

On some boards, under heavy load, the EC firmware is
unable to complete commands even in one second. Increasing
the command completion timeout value to five seconds.

Reported-by: Quanxian Wang <quanxian.wang@intel.com>
Fixes: c1b0bc2dabfa ("usb: typec: Add support for UCSI interface")
Cc: <stable@vger.kernel.org>
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

USB: serial: cp210x: add ID for NI USB serial console

commit 1e23aace21515a8f7615a1de016c0ea8d4e0cc6e upstream.

Added the USB VID and PID for the USB serial console on some National
Instruments devices.

Signed-off-by: Kyle Roeschley <kyle.roeschley@ni.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

USB: serial: ftdi_sio: use jtag quirk for Arrow USB Blaster

commit 470b5d6f0cf4674be2d1ec94e54283a1770b6a1a upstream.

Arrow USB Blaster integrated on MAX1000 board uses the same vendor ID
(0x0403) and product ID (0x6010) as the "original" FTDI device.

This patch avoids picking up by ftdi_sio of the first interface of this
USB device. After that this device can be used by Arrow user-space JTAG
driver.

Signed-off-by: Vasyl Vavrychuk <vvavrychuk@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

USB: serial: simple: add libtransistor console

commit fe710508b6ba9d28730f3021fed70e7043433b2e upstream.

Add simple driver for libtransistor USB console.
This device is implemented in software:
https://github.com/reswitched/libtransistor/blob/development/lib/usb_serial.c

Signed-off-by: Collin May <collin@collinswebsite.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

xhci: Fix USB ports for Dell Inspiron 5775

commit 621faf4f6a181b6e012c1d1865213f36f4159b7f upstream.

The Dell Inspiron 5775 is a Raven Ridge. The Enable Slot command timed
out when a USB device gets plugged:
[ 212.156326] xhci_hcd 0000:03:00.3: Error while assigning device slot ID
[ 212.156340] xhci_hcd 0000:03:00.3: Max number of devices this xHCI host supports is 64.
[ 212.156348] usb usb2-port3: couldn't allocate usb_device

AMD suggests that a delay before xHC suspends can fix the issue.

I can confirm it fixes the issue, so use the suspend delay quirk for
Raven Ridge's xHC.

Cc: stable@vger.kernel.org
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Revert "xhci: plat: Register shutdown for xhci_plat"

commit c20f53c58261b121d0989e147368803b9773b413 upstream.

This reverts commit b07c12517f2aed0add8ce18146bb426b14099392

It is incomplete and causes hangs on devices when shutting down.  It
needs a much more "complete" fix in order to work properly.  As that fix
has not been merged, revert this patch for now before it causes any more
problems.

Cc: Greg Hackmann <ghackmann@google.com>
Cc: Adam Wallis <awallis@codeaurora.org>
Cc: Mathias Nyman <mathias.nyman@intel.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

usbip: vhci_hcd: check rhport before using in vhci_hub_control()

commit 5b22f676118ff25049382041da0db8012e57c9e8 upstream.

Validate !rhport < 0 before using it to access port_status array.

Signed-off-by: Shuah Khan <shuahkh@osg.samsung.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

usbip: vhci_hcd: Fix usb device and sockfd leaks

commit 9020a7efe537856eb3e826ebebdf38a5d07a7857 upstream.

vhci_hcd fails to do reset to put usb device and sockfd in the
module remove/stop paths. Fix the leak.

Signed-off-by: Shuah Khan <shuahkh@osg.samsung.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

usbip: usbip_host: fix to hold parent lock for device_attach() calls

commit 4bfb141bc01312a817d36627cc47c93f801c216d upstream.

usbip_host calls device_attach() without holding dev->parent lock.
Fix it.

Signed-off-by: Shuah Khan <shuahkh@osg.samsung.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

usbip: usbip_event: fix to not print kernel pointer address

commit 4c982482341c64f55daf69b6caa5a2bcd9b43824 upstream.

Fix it to not print kernel pointer address. Remove the conditional
and debug message as it isn't very useful.

Signed-off-by: Shuah Khan <shuahkh@osg.samsung.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

random: rate limit unseeded randomness warnings

commit 4e00b339e264802851aff8e73cde7d24b57b18ce upstream.

On systems without sufficient boot randomness, no point spamming dmesg.

Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

random: fix possible sleeping allocation from irq context

commit 6c1e851c4edc13a43adb3ea4044e3fc8f43ccf7d upstream.

We can do a sleeping allocation from an irq context when CONFIG_NUMA
is enabled.  Fix this by initializing the NUMA crng instances in a
workqueue.

Reported-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Reported-by: syzbot+9de458f6a5e713ee8c1a@syzkaller.appspotmail.com
Fixes: 8ef35c866f8862df ("random: set up the NUMA crng instances...")
Cc: stable@vger.kernel.org
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

random: set up the NUMA crng instances after the CRNG is fully initialized

commit 8ef35c866f8862df074a49a93b0309725812dea8 upstream.

Until the primary_crng is fully initialized, don't initialize the NUMA
crng nodes.  Otherwise users of /dev/urandom on NUMA systems before
the CRNG is fully initialized can get very bad quality randomness.  Of
course everyone should move to getrandom(2) where this won't be an
issue, but there's a lot of legacy code out there.  This related to
CVE-2018-1108.

Reported-by: Jann Horn <jannh@google.com>
Fixes: 1e7f583af67b ("random: make /dev/urandom scalable for silly...")
Cc: stable@kernel.org # 4.8+
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ext4: fix bitmap position validation

commit 22be37acce25d66ecf6403fc8f44df9c5ded2372 upstream.

Currently in ext4_valid_block_bitmap() we expect the bitmap to be
positioned anywhere between 0 and s_blocksize clusters, but that's
wrong because the bitmap can be placed anywhere in the block group. This
causes false positives when validating bitmaps on perfectly valid file
system layouts. Fix it by checking whether the bitmap is within the group
boundary.

The problem can be reproduced using the following

mkfs -t ext3 -E stride=256 /dev/vdb1
mount /dev/vdb1 /mnt/test
cd /mnt/test
wget https://cdn.kernel.org/pub/linux/kernel/v4.x/linux-4.16.3.tar.xz
tar xf linux-4.16.3.tar.xz

This will result in the warnings in the logs

EXT4-fs error (device vdb1): ext4_validate_block_bitmap:399: comm tar: bg 84: block 2774529: invalid block bitmap

[ Changed slightly for clarity and to not drop a overflow test -- TYT ]

Signed-off-by: Lukas Czerner <lczerner@redhat.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Reported-by: Ilya Dryomov <idryomov@gmail.com>
Fixes: 7dac4a1726a9 ("ext4: add validity checks for bitmap block numbers")
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ext4: add validity checks for bitmap block numbers

commit 7dac4a1726a9c64a517d595c40e95e2d0d135f6f upstream.

An privileged attacker can cause a crash by mounting a crafted ext4
image which triggers a out-of-bounds read in the function
ext4_valid_block_bitmap() in fs/ext4/balloc.c.

This issue has been assigned CVE-2018-1093.

BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=199181
BugLink: https://bugzilla.redhat.com/show_bug.cgi?id=1560782
Reported-by: Wen Xu <wen.xu@gatech.edu>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ext4: add MODULE_SOFTDEP to ensure crc32c is included in the initramfs

commit 7ef79ad52136712172eb0525bf0b462516bf2f93 upstream.

Fixes: a45403b51582 ("ext4: always initialize the crc32c checksum driver")
Reported-by: François Valenduc <francoisvalenduc@gmail.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ext4: set h_journal if there is a failure starting a reserved handle

commit b2569260d55228b617bd82aba6d0db2faeeb4116 upstream.

If ext4 tries to start a reserved handle via
jbd2_journal_start_reserved(), and the journal has been aborted, this
can result in a NULL pointer dereference.  This is because the fields
h_journal and h_transaction in the handle structure share the same
memory, via a union, so jbd2_journal_start_reserved() will clear
h_journal before calling start_this_handle().  If this function fails
due to an aborted handle, h_journal will still be NULL, and the call
to jbd2_journal_free_reserved() will pass a NULL journal to
sub_reserve_credits().

This can be reproduced by running "kvm-xfstests -c dioread_nolock
generic/475".

Cc: stable@kernel.org # 3.11
Fixes: 8f7d89f36829b ("jbd2: transaction reservation support")
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Reviewed-by: Andreas Dilger <adilger@dilger.ca>
Reviewed-by: Jan Kara <jack@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ext4: prevent right-shifting extents beyond EXT_MAX_BLOCKS

commit 349fa7d6e1935f49bf4161c4900711b2989180a9 upstream.

During the "insert range" fallocate operation, extents starting at the
range offset are shifted "right" (to a higher file offset) by the range
length.  But, as shown by syzbot, it's not validated that this doesn't
cause extents to be shifted beyond EXT_MAX_BLOCKS.  In that case
->ee_block can wrap around, corrupting the extent tree.

Fix it by returning an error if the space between the end of the last
extent and EXT4_MAX_BLOCKS is smaller than the range being inserted.

This bug can be reproduced by running the following commands when the
current directory is on an ext4 filesystem with a 4k block size:

        fallocate -l 8192 file
        fallocate --keep-size -o 0xfffffffe000 -l 4096 -n file
        fallocate --insert-range -l 8192 file

Then after unmounting the filesystem, e2fsck reports corruption.

Reported-by: syzbot+06c885be0edcdaeab40c@syzkaller.appspotmail.com
Fixes: 331573febb6a ("ext4: Add support FALLOC_FL_INSERT_RANGE for fallocate")
Cc: stable@vger.kernel.org # v4.2+
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Linux 4.14.38

ACPI / video: Only default only_lcd to true on Win8-ready _desktops_

commit 53fa1f6e8a5958da698a31edf366ffe90596b490 upstream.

Commit 5928c281524f (ACPI / video: Default lcd_only to true on Win8-ready
and newer machines) made only_lcd default to true on all machines where
acpi_osi_is_win8() returns true, including laptops.

The purpose of this is to avoid the bogus / non-working acpi backlight
interface which many newer BIOS-es define on desktop machines.

But this is causing a regression on some laptops, specifically on the
Dell XPS 13 2013 model, which does not have the LCD flag set for its
fully functional ACPI backlight interface.

Rather then DMI quirking our way out of this, this commits changes the
logic for setting only_lcd to true, to only do this on machines with
a desktop (or server) dmi chassis-type.

Note that we cannot simply only check the chassis-type and not register
the backlight interface based on that as there are some laptops and
tablets which have their chassis-type set to "3" aka desktop. Hopefully
the combination of checking the LCD flag, but only on devices with
a desktop(ish) chassis-type will avoid the needs for DMI quirks for this,
or at least limit the amount of DMI quirks which we need to a minimum.

Fixes: 5928c281524f (ACPI / video: Default lcd_only to true on Win8-ready and newer machines)
Reported-and-tested-by: James Hogan <jhogan@kernel.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Cc: 4.15+ <stable@vger.kernel.org> # 4.15+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

s390/uprobes: implement arch_uretprobe_is_alive()

commit 783c3b53b9506db3e05daacfe34e0287eebb09d8 upstream.

Implement s390 specific arch_uretprobe_is_alive() to avoid SIGSEGVs
observed with uretprobes in combination with setjmp/longjmp.

See commit 2dea1d9c38e4 ("powerpc/uprobes: Implement
arch_uretprobe_is_alive()") for more details.

With this implemented all test cases referenced in the above commit
pass.

Reported-by: Ziqian SUN <zsun@redhat.com>
Cc: <stable@vger.kernel.org> # v4.3+
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

s390/dasd: fix IO error for newly defined devices

commit 5d27a2bf6e14f5c7d1033ad1e993fcd0eba43e83 upstream.

When a new CKD storage volume is defined at the storage server, Linux
may be relying on outdated information about that volume, which leads to
the following errors:

1. Command Reject Errors for minidisk on z/VM:

dasd-eckd.b3193d: 0.0.XXXX: An error occurred in the DASD device driver,
  reason=09
dasd(eckd): I/O status report for device 0.0.XXXX:
dasd(eckd): in req: 00000000XXXXXXXX CC:00 FC:04 AC:00 SC:17 DS:02 CS:00
    RC:0
dasd(eckd): device 0.0.2046: Failing CCW: 00000000XXXXXXXX
dasd(eckd): Sense(hex)  0- 7: 80 00 00 00 00 00 00 00
dasd(eckd): Sense(hex)  8-15: 00 00 00 00 00 00 00 00
dasd(eckd): Sense(hex) 16-23: 00 00 00 00 e1 00 0f 00
dasd(eckd): Sense(hex) 24-31: 00 00 40 e2 00 00 00 00
dasd(eckd): 24 Byte: 0 MSG 0, no MSGb to SYSOP

2. Equipment Check errors on LPAR or for dedicated devices on z/VM:

dasd(eckd): I/O status report for device 0.0.XXXX:
dasd(eckd): in req: 00000000XXXXXXXX CC:00 FC:04 AC:00 SC:17 DS:0E CS:40
    fcxs:01 schxs:00 RC:0
dasd(eckd): device 0.0.9713: Failing TCW: 00000000XXXXXXXX
dasd(eckd): Sense(hex)  0- 7: 10 00 00 00 13 58 4d 0f
dasd(eckd): Sense(hex)  8-15: 67 00 00 00 00 00 00 04
dasd(eckd): Sense(hex) 16-23: e5 18 05 33 97 01 0f 0f
dasd(eckd): Sense(hex) 24-31: 00 00 40 e2 00 04 58 0d
dasd(eckd): 24 Byte: 0 MSG f, no MSGb to SYSOP

Fix this problem by using the up-to-date information provided during
online processing via the device specific SNEQ to detect the case of
outdated LCU data. If there is a difference, perform a re-read of that
data.

Cc: stable@vger.kernel.org
Reviewed-by: Jan Hoeppner <hoeppner@linux.ibm.com>
Signed-off-by: Stefan Haberland <sth@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

s390/cio: update chpid descriptor after resource accessibility event

commit af2e460ade0b0180d0f3812ca4f4f59cc9597f3e upstream.

Channel path descriptors have been seen as something stable (as
long as the chpid is configured). Recent tests have shown that the
descriptor can also be altered when the link state of a channel path
changes. Thus it is necessary to update the descriptor during
handling of resource accessibility events.

Cc: <stable@vger.kernel.org>
Signed-off-by: Sebastian Ott <sebott@linux.ibm.com>
Reviewed-by: Peter Oberparleiter <oberpar@linux.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

tracing: Fix missing tab for hwlat_detector print format

commit 9a0fd675304d410f3a9586e1b333e16f4658d56c upstream.

It's been missing for a while but no one is touching that up.  Fix it.

Link: http://lkml.kernel.org/r/20180315060639.9578-1-peterx@redhat.com
CC: Ingo Molnar <mingo@kernel.org>
Cc:stable@vger.kernel.org
Fixes: 7b2c86250122d ("tracing: Add NMI tracing in hwlat detector")
Signed-off-by: Peter Xu <peterx@redhat.com>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

block/swim: Fix IO error at end of medium

commit 5a13388d7aa1177b98d7168330ecbeeac52f844d upstream.

Reading to the end of a 720K disk results in an IO error instead of EOF
because the block layer thinks the disk has 2880 sectors. (Partly this
is a result of inverted logic of the ONEMEG_MEDIA bit that's now fixed.)

Initialize the density and head count in swim_add_floppy() to agree
with the device size passed to set_capacity() during drive probe.

Call set_capacity() again upon device open, after refreshing the density
and head count values.

Cc: Laurent Vivier <lvivier@redhat.com>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: stable@vger.kernel.org # v4.14+
Tested-by: Stan Johnson <userm57@yahoo.com>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Acked-by: Laurent Vivier <lvivier@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

block/swim: Fix array bounds check

commit 7ae6a2b6cc058005ee3d0d2b9ce27688e51afa4b upstream.

In the floppy_find() function in swim.c is a call to
get_disk(swd->unit[drive].disk). The actual parameter to this call
can be a NULL pointer when drive == swd->floppy_count. This causes
an oops in get_disk().

Data read fault at 0x00000198 in Super Data (pc=0x1be5b6)
BAD KERNEL BUSERR
Oops: 00000000
Modules linked in: swim_mod ipv6 mac8390
PC: [<001be5b6>] get_disk+0xc/0x76
SR: 2004  SP: 9a078bc1  a2: 0213ed90
d0: 00000000    d1: 00000000    d2: 00000000    d3: 000000ff
d4: 00000002    d5: 02983590    a0: 02332e00    a1: 022dfd64
Process dd (pid: 285, task=020ab25b)
Frame format=B ssw=074d isc=4a88 isb=6732 daddr=00000198 dobuf=00000000
baddr=001be5bc dibuf=bfffffff ver=f
Stack from 022dfca4:
        00000000 0203fc00 0213ed90 022dfcc0 02982936 00000000 00200000 022dfd08
        0020f85a 00200000 022dfd64 02332e00 004040fc 00000014 001be77e 022dfd64
        00334e4a 001be3f8 0800001d 022dfd64 01c04b60 01c04b70 022aba80 029828f8
        02332e00 022dfd2c 001be7ac 0203fc00 00200000 022dfd64 02103a00 01c04b60
        01c04b60 0200e400 022dfd68 000e191a 00200000 022dfd64 02103a00 0800001d
        00000000 00000003 000b89de 00500000 02103a00 01c04b60 02103a08 01c04c2e
Call Trace: [<02982936>] floppy_find+0x3e/0x4a [swim_mod]
 [<00200000>] uart_remove_one_port+0x1a2/0x260
 [<0020f85a>] kobj_lookup+0xde/0x132
 [<00200000>] uart_remove_one_port+0x1a2/0x260
 [<001be77e>] get_gendisk+0x0/0x130
 [<00334e4a>] mutex_lock+0x0/0x2e
 [<001be3f8>] disk_block_events+0x0/0x6c
 [<029828f8>] floppy_find+0x0/0x4a [swim_mod]
 [<001be7ac>] get_gendisk+0x2e/0x130
 [<00200000>] uart_remove_one_port+0x1a2/0x260
 [<000e191a>] __blkdev_get+0x32/0x45a
 [<00200000>] uart_remove_one_port+0x1a2/0x260
 [<000b89de>] complete_walk+0x0/0x8a
 [<000e1e22>] blkdev_get+0xe0/0x29a
 [<000e1fdc>] blkdev_open+0x0/0xb0
 [<000b89de>] complete_walk+0x0/0x8a
 [<000e1fdc>] blkdev_open+0x0/0xb0
 [<000e01cc>] bd_acquire+0x74/0x8a
 [<000e205c>] blkdev_open+0x80/0xb0
 [<000e1fdc>] blkdev_open+0x0/0xb0
 [<000abf24>] do_dentry_open+0x1a4/0x322
 [<00020000>] __do_proc_douintvec+0x22/0x27e
 [<000b89de>] complete_walk+0x0/0x8a
 [<000baa62>] link_path_walk+0x0/0x48e
 [<000ba3f8>] inode_permission+0x20/0x54
 [<000ac0e4>] vfs_open+0x42/0x78
 [<000bc372>] path_openat+0x2b2/0xeaa
 [<000bc0c0>] path_openat+0x0/0xeaa
 [<0004463e>] __irq_wake_thread+0x0/0x4e
 [<0003a45a>] task_tick_fair+0x18/0xc8
 [<000bd00a>] do_filp_open+0xa0/0xea
 [<000abae0>] do_sys_open+0x11a/0x1ee
 [<00020000>] __do_proc_douintvec+0x22/0x27e
 [<000abbf4>] SyS_open+0x1e/0x22
 [<00020000>] __do_proc_douintvec+0x22/0x27e
 [<00002b40>] syscall+0x8/0xc
 [<00020000>] __do_proc_douintvec+0x22/0x27e
 [<0000c00b>] dyadic+0x1/0x28
Code: 4e5e 4e75 4e56 fffc 2f0b 2f02 266e 0008 <206b> 0198 4a88 6732 2428 002c 661e 486b 0058 4eb9 0032 0b96 588f 4a88 672c 2008
Disabling lock debugging due to kernel taint

Fix the array index bounds check to avoid this.

Cc: Laurent Vivier <lvivier@redhat.com>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: stable@vger.kernel.org # v4.14+
Fixes: 8852ecd97488 ("[PATCH] m68k: mac - Add SWIM floppy support")
Tested-by: Stan Johnson <userm57@yahoo.com>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Acked-by: Laurent Vivier <lvivier@redhat.com>
Reviewed-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

block/swim: Select appropriate drive on device open

commit b3906535ccc6cd04c42f9b1c7e31d1947b3ebc74 upstream.

The driver supports internal and external FDD units so the floppy_open
function must not hard-code the drive location.

Cc: Laurent Vivier <lvivier@redhat.com>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: stable@vger.kernel.org # v4.14+
Tested-by: Stan Johnson <userm57@yahoo.com>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Acked-by: Laurent Vivier <lvivier@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

block/swim: Rename macros to avoid inconsistent inverted logic

commit 56a1c5ee54f69dd767fb61d301883dc919ddc259 upstream.

The Sony drive status bits use active-low logic. The swim_readbit()
function converts that to 'C' logic for readability. Hence, the
sense of the names of the status bit macros should not be inverted.

Mostly they are correct. However, the TWOMEG_DRIVE, MFM_MODE and
TWOMEG_MEDIA macros have inverted sense (like MkLinux). Fix this
inconsistency and make the following patches less confusing.

The same problem affects swim3.c so fix that too.

No functional change.

The FDHD drive status bits are documented in sonydriv.cpp from MAME
and in swimiii.h from MkLinux.

Cc: Laurent Vivier <lvivier@redhat.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: linuxppc-dev@lists.ozlabs.org
Cc: Jens Axboe <axboe@kernel.dk>
Cc: stable@vger.kernel.org # v4.14+
Tested-by: Stan Johnson <userm57@yahoo.com>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Acked-by: Laurent Vivier <lvivier@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

block/swim: Remove extra put_disk() call from error path

commit c1d6207cc0eef2a7f8551f9c7420d8776268f6e1 upstream.

Cc: Laurent Vivier <lvivier@redhat.com>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: stable@vger.kernel.org # v4.14+
Fixes: 103db8b2dfa5 ("[PATCH] swim: stop sharing request queue across multiple gendisks")
Tested-by: Stan Johnson <userm57@yahoo.com>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Acked-by: Laurent Vivier <lvivier@redhat.com>
Reviewed-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

block/swim: Don't log an error message for an invalid ioctl

commit 8e2ab5a4efaac77fb93e5b5b109d0b3976fdd3a0 upstream.

The 'eject' shell command may send various different ioctl commands.
This leads to error messages on the console even though the FDEJECT
ioctl succeeds.

~# eject floppy
SWIM floppy_ioctl: unknown cmd 21257
SWIM floppy_ioctl: unknown cmd 1

Don't log an error message for an invalid ioctl, just do as the
swim3 driver does and return -ENOTTY.

Cc: Laurent Vivier <lvivier@redhat.com>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: stable@vger.kernel.org # v4.14+
Tested-by: Stan Johnson <userm57@yahoo.com>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Acked-by: Laurent Vivier <lvivier@redhat.com>
Reviewed-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

block/swim: Check drive type

commit 8a500df63d07d8aee44b7ee2c54e462e47ce93ec upstream.

The SWIM chip is compatible with GCR-mode Sony 400K/800K drives but
this driver only supports MFM mode. Therefore only Sony FDHD drives
are supported. Skip incompatible drives.

Cc: Laurent Vivier <lvivier@redhat.com>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: stable@vger.kernel.org # v4.14+
Tested-by: Stan Johnson <userm57@yahoo.com>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Acked-by: Laurent Vivier <lvivier@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

m68k/mac: Don't remap SWIM MMIO region

commit b64576cbf36afa5fabf3b31f62a1994c429ef855 upstream.

For reasons I don't understand, calling ioremap() then iounmap() on
the SWIM MMIO region causes a hang on 68030 (but not on 68040).

~# modprobe swim_mod
SWIM floppy driver Version 0.2 (2008-10-30)
SWIM device not found !
watchdog: BUG: soft lockup - CPU#0 stuck for 23s! [modprobe:285]
Modules linked in: swim_mod(+)
Format 00  Vector: 0064  PC: 000075aa  Status: 2000    Not tainted
ORIG_D0: ffffffff  D0: d00c0000  A2: 007c2370  A1: 003f810c
A0: 00040000  D5: d0096800  D4: d0097e00
D3: 00000001  D2: 00000003  D1: 00000000
Non-Maskable Interrupt
Modules linked in: swim_mod(+)
PC: [<000075ba>] __iounmap+0x24/0x10e
SR: 2000  SP: 007abc48  a2: 007c2370
d0: d00c0000    d1: 000001a0    d2: 00000019    d3: 00000001
d4: d0097e00    d5: d0096800    a0: 00040000    a1: 003f810c
Process modprobe (pid: 285, task=007c2370)
Frame format=0
Stack from 007abc7c:
        ffffffed 00000000 006a4060 004712e0 007abca0 000076ea d0080000 00080000
        010bb4b8 007abcd8 010ba542 d0096000 00000000 00000000 00000001 010bb59c
        00000000 007abf30 010bb4b8 0047760a 0047763c 00477612 00616540 007abcec
        0020a91a 00477600 0047760a 010bb4cc 007abd18 002092f2 0047760a 00333b06
        007abd5c 00000000 0047760a 010bb4cc 00404f90 004776b8 00000001 007abd38
        00209446 010bb4cc 0047760a 010bb4cc 0020938e 0031f8be 00616540 007abd64
Call Trace: [<000076ea>] iounmap+0x46/0x5a
 [<00080000>] shrink_page_list+0x7f6/0xe06
 [<010ba542>] swim_probe+0xe4/0x496 [swim_mod]
 [<0020a91a>] platform_drv_probe+0x20/0x5e
 [<002092f2>] driver_probe_device+0x21c/0x2b8
 [<00333b06>] mutex_lock+0x0/0x2e
 [<00209446>] __driver_attach+0xb8/0xce
 [<0020938e>] __driver_attach+0x0/0xce
 [<0031f8be>] klist_next+0x0/0xa0
 [<00207562>] bus_for_each_dev+0x74/0xba
 [<000344c0>] blocking_notifier_call_chain+0x0/0x20
 [<00333b06>] mutex_lock+0x0/0x2e
 [<00208e44>] driver_attach+0x1a/0x1e
 [<0020938e>] __driver_attach+0x0/0xce
 [<00207e26>] bus_add_driver+0x188/0x234
 [<000344c0>] blocking_notifier_call_chain+0x0/0x20
 [<00209894>] driver_register+0x58/0x104
 [<000344c0>] blocking_notifier_call_chain+0x0/0x20
 [<010bd000>] swim_init+0x0/0x2c [swim_mod]
 [<0020a7be>] __platform_driver_register+0x38/0x3c
 [<010bd028>] swim_init+0x28/0x2c [swim_mod]
 [<000020dc>] do_one_initcall+0x38/0x196
 [<000344c0>] blocking_notifier_call_chain+0x0/0x20
 [<003331cc>] mutex_unlock+0x0/0x3e
 [<00333b06>] mutex_lock+0x0/0x2e
 [<003331cc>] mutex_unlock+0x0/0x3e
 [<00333b06>] mutex_lock+0x0/0x2e
 [<003331cc>] mutex_unlock+0x0/0x3e
 [<00333b06>] mutex_lock+0x0/0x2e
 [<003331cc>] mutex_unlock+0x0/0x3e
 [<00333b06>] mutex_lock+0x0/0x2e
 [<00075008>] __free_pages+0x0/0x38
 [<000045c0>] mangle_kernel_stack+0x30/0xda
 [<000344c0>] blocking_notifier_call_chain+0x0/0x20
 [<003331cc>] mutex_unlock+0x0/0x3e
 [<00333b06>] mutex_lock+0x0/0x2e
 [<0005ced4>] do_init_module+0x42/0x266
 [<010bd000>] swim_init+0x0/0x2c [swim_mod]
 [<000344c0>] blocking_notifier_call_chain+0x0/0x20
 [<0005eda0>] load_module+0x1a30/0x1e70
 [<0000465d>] mangle_kernel_stack+0xcd/0xda
 [<00331c64>] __generic_copy_from_user+0x0/0x46
 [<0033256e>] _cond_resched+0x0/0x32
 [<00331b9c>] memset+0x0/0x98
 [<0033256e>] _cond_resched+0x0/0x32
 [<0005f25c>] SyS_init_module+0x7c/0x112
 [<00002000>] _start+0x0/0x8
 [<00002000>] _start+0x0/0x8
 [<00331c82>] __generic_copy_from_user+0x1e/0x46
 [<0005f2b2>] SyS_init_module+0xd2/0x112
 [<0000465d>] mangle_kernel_stack+0xcd/0xda
 [<00002b40>] syscall+0x8/0xc
 [<0000465d>] mangle_kernel_stack+0xcd/0xda
 [<0008c00c>] pcpu_balance_workfn+0xb2/0x40e
Code: 2200 7419 e4a9 e589 2841 d9fc 0000 1000 <2414> 7203 c282 7602 b681 6600 0096 0242 fe00 0482 0000 0000 e9c0 11c3 ed89 2642

There's no need to call ioremap() for the SWIM address range, as it lies
within the usual IO device region at 0x5000 0000, which has already been
mapped by head.S.

Remove the redundant ioremap() and iounmap() calls to fix the hang.

Cc: Laurent Vivier <lvivier@redhat.com>
Cc: stable@vger.kernel.org # v4.14+
Tested-by: Stan Johnson <userm57@yahoo.com>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Acked-by: Laurent Vivier <lvivier@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

fsnotify: Fix fsnotify_mark_connector race

commit d90a10e2444ba5a351fa695917258ff4c5709fa5 upstream.

fsnotify() acquires a reference to a fsnotify_mark_connector through
the SRCU-protected pointer to_tell->i_fsnotify_marks. However, it
appears that no precautions are taken in fsnotify_put_mark() to
ensure that fsnotify() drops its reference to this
fsnotify_mark_connector before assigning a value to its 'destroy_next'
field. This can result in fsnotify_put_mark() assigning a value
to a connector's 'destroy_next' field right before fsnotify() tries to
traverse the linked list referenced by the connector's 'list' field.
Since these two fields are members of the same union, this behavior
results in a kernel panic.

This issue is resolved by moving the connector's 'destroy_next' field
into the object pointer union. This should work since the object pointer
access is protected by both a spinlock and the value of the 'flags'
field, and the 'flags' field is cleared while holding the spinlock in
fsnotify_put_mark() before 'destroy_next' is updated. It shouldn't be
possible for another thread to accidentally read from the object pointer
after the 'destroy_next' field is updated.

The offending behavior here is extremely unlikely; since
fsnotify_put_mark() removes references to a connector (specifically,
it ensures that the connector is unreachable from the inode it was
formerly attached to) before updating its 'destroy_next' field, a
sizeable chunk of code in fsnotify_put_mark() has to execute in the
short window between when fsnotify() acquires the connector reference
and saves the value of its 'list' field. On the HEAD kernel, I've only
been able to reproduce this by inserting a udelay(1) in fsnotify().
However, I've been able to reproduce this issue without inserting a
udelay(1) anywhere on older unmodified release kernels, so I believe
it's worth fixing at HEAD.

References: https://bugzilla.kernel.org/show_bug.cgi?id=199437
Fixes: 08991e83b7286635167bab40927665a90fb00d81
CC: stable@vger.kernel.org
Signed-off-by: Robert Kolchmeyer <rkolchmeyer@google.com>
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

cdrom: information leak in cdrom_ioctl_media_changed()

commit 9de4ee40547fd315d4a0ed1dd15a2fa3559ad707 upstream.

This cast is wrong.  "cdi->capacity" is an int and "arg" is an unsigned
long.  The way the check is written now, if one of the high 32 bits is
set then we could read outside the info->slots[] array.

This bug is pretty old and it predates git.

Reviewed-by: Christoph Hellwig <hch@lst.de>
Cc: stable@vger.kernel.org
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

scsi: mptsas: Disable WRITE SAME

commit 94e5395d2403c8bc2504a7cbe4c4caaacb7b8b84 upstream.

First generation MPT Fusion controllers can not translate WRITE SAME
when the attached device is a SATA drive. Disable WRITE SAME support.

Reported-by: Nikola Ciprich <nikola.ciprich@linuxbox.cz>
Cc: <stable@vger.kernel.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commoncap: Handle memory allocation failure.

commit 1f5781725dcbb026438e77091c91a94f678c3522 upstream.

syzbot is reporting NULL pointer dereference at xattr_getsecurity() [1],
for cap_inode_getsecurity() is returning sizeof(struct vfs_cap_data) when
memory allocation failed. Return -ENOMEM if memory allocation failed.

[1] https://syzkaller.appspot.com/bug?id=a55ba438506fe68649a5f50d2d82d56b365e0107

Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Fixes: 8db6c34f1dbc8e06 ("Introduce v3 namespaced file capabilities")
Reported-by: syzbot <syzbot+9369930ca44f29e60e2d@syzkaller.appspotmail.com>
Cc: stable <stable@vger.kernel.org> # 4.14+
Acked-by: Serge E. Hallyn <serge@hallyn.com>
Acked-by: James Morris <james.morris@microsoft.com>
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Revert "mm/hmm: fix header file if/else/endif maze"

This reverts commit 25df8b83e867dcfb660123e9589ebf6f094fcdd3 which is
commit b28b08de436a638c82d0cf3dcdbdbad055baf1fc upstream.

There are still build errors with this patch applied, and the upstream
patches do not seem to apply anymore, so reverting this patch seems like
the best thing to do at this point in time.

Reported-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Михаил Носов <drdeimosnn@gmail.com>
Cc: Jérôme Glisse <jglisse@redhat.com>
Cc: Balbir Singh <bsingharora@gmail.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Ralph Campbell <rcampbell@nvidia.com>
Cc: John Hubbard <jhubbard@nvidia.com>
Cc: Evgeny Baskakov <ebaskakov@nvidia.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

arm64: dts: rockchip: remove vdd_log from rk3399-puma

commit 87eba0716011e528f7841026f2cc65683219d0ad upstream.

vdd_log has no consumer and therefore will not be set to a specific
voltage. Still the PWM output pin gets configured and thence the vdd_log
output voltage will changed from it's default. Depending on the idle
state of the PWM this will slightly over or undervoltage the logic supply
of the RK3399 and cause instability with GbE (undervoltage) and PCIe
(overvoltage). Since the default value set by a voltage divider is the
correct supply voltage and we don't need to change it during runtime we
remove the rail from the devicetree completely so the PWM pin will not
be configured.

Signed-off-by: Klaus Goger <klaus.goger@theobroma-systems.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Cc: Jakob Unterwurzacher <jakob.unterwurzacher@theobroma-systems.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

microblaze: Setup dependencies for ASM optimized lib functions

commit 18ffc0cce4ff947a2acc9b2e06ae5309a6e6fb43 upstream.

The patch:
"microblaze: Setup proper dependency for optimized lib functions"
(sha1: 7b6ce52be3f86520524711a6f33f3866f9339694)
didn't setup all dependencies properly.
Optimized lib functions in C are also present for little endian
and optimized library functions in assembler are implemented only for
big endian version.

Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

s390: correct module section names for expoline code revert

[ Upstream commit 6cf09958f32b9667bb3ebadf74367c791112771b ]

The main linker script vmlinux.lds.S for the kernel image merges
the expoline code patch tables into two section ".nospec_call_table"
and ".nospec_return_table". This is *not* done for the modules,
there the sections retain their original names as generated by gcc:
".s390_indirect_call", ".s390_return_mem" and ".s390_return_reg".

The module_finalize code has to check for the compiler generated
section names, otherwise no code patching is done. This slows down
the module code in case of "spectre_v2=off".

Cc: stable@vger.kernel.org # 4.16
Fixes: f19fbd5ed6 ("s390: introduce execute-trampolines for branches")
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

s390: correct nospec auto detection init order

[ Upstream commit 6a3d1e81a434fc311f224b8be77258bafc18ccc6 ]

With CONFIG_EXPOLINE_AUTO=y the call of spectre_v2_auto_early() via
early_initcall is done *after* the early_param functions. This
overwrites any settings done with the nobp/no_spectre_v2/spectre_v2
parameters. The code patching for the kernel is done after the
evaluation of the early parameters but before the early_initcall
is done. The end result is a kernel image that is patched correctly
but the kernel modules are not.

Make sure that the nospec auto detection function is called before the
early parameters are evaluated and before the code patching is done.

Fixes: 6e179d64126b ("s390: add automatic detection of the spectre defense")
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

s390: add sysfs attributes for spectre

[ Upstream commit d424986f1d6b16079b3231db0314923f4f8deed1 ]

Set CONFIG_GENERIC_CPU_VULNERABILITIES and provide the two functions
cpu_show_spectre_v1 and cpu_show_spectre_v2 to report the spectre
mitigations.

Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

s390: report spectre mitigation via syslog

[ Upstream commit bc035599718412cfba9249aa713f90ef13f13ee9 ]

Add a boot message if either of the spectre defenses is active.
The message is
    "Spectre V2 mitigation: execute trampolines."
or  "Spectre V2 mitigation: limited branch prediction."

Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

s390: add automatic detection of the spectre defense

[ Upstream commit 6e179d64126b909f0b288fa63cdbf07c531e9b1d ]

Automatically decide between nobp vs. expolines if the spectre_v2=auto
kernel parameter is specified or CONFIG_EXPOLINE_AUTO=y is set.

The decision made at boot time due to CONFIG_EXPOLINE_AUTO=y being set
can be overruled with the nobp, nospec and spectre_v2 kernel parameters.

Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

s390: move nobp parameter functions to nospec-branch.c

[ Upstream commit b2e2f43a01bace1a25bdbae04c9f9846882b727a ]

Keep the code for the nobp parameter handling with the code for
expolines. Both are related to the spectre v2 mitigation.

Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

s390/entry.S: fix spurious zeroing of r0

[ Upstream commit d3f468963cd6fd6d2aa5e26aed8b24232096d0e1 ]

when a system call is interrupted we might call the critical section
cleanup handler that re-does some of the operations. When we are between
.Lsysc_vtime and .Lsysc_do_svc we might also redo the saving of the
problem state registers r0-r7:

.Lcleanup_system_call:
[...]
0:      # update accounting time stamp
        mvc     __LC_LAST_UPDATE_TIMER(8),__LC_SYNC_ENTER_TIMER
        # set up saved register r11
        lg      %r15,__LC_KERNEL_STACK
        la      %r9,STACK_FRAME_OVERHEAD(%r15)
        stg     %r9,24(%r11)            # r11 pt_regs pointer
        # fill pt_regs
        mvc     __PT_R8(64,%r9),__LC_SAVE_AREA_SYNC
--->    stmg    %r0,%r7,__PT_R0(%r9)

The problem is now, that we might have already zeroed out r0.
The fix is to move the zeroing of r0 after sysc_do_svc.

Reported-by: Farhan Ali <alifm@linux.vnet.ibm.com>
Fixes: 7041d28115e91 ("s390: scrub registers on kernel entry and KVM exit")
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

s390: do not bypass BPENTER for interrupt system calls

[ Upstream commit d5feec04fe578c8dbd9e2e1439afc2f0af761ed4 ]

The system call path can be interrupted before the switch back to the
standard branch prediction with BPENTER has been done. The critical
section cleanup code skips forward to .Lsysc_do_svc and bypasses the
BPENTER. In this case the kernel and all subsequent code will run with
the limited branch prediction.

Fixes: eacf67eb9b32 ("s390: run user space and KVM guests with modified branch prediction")
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

s390: Replace IS_ENABLED(EXPOLINE_*) with IS_ENABLED(CONFIG_EXPOLINE_*)

[ Upstream commit 2cb370d615e9fbed9e95ed222c2c8f337181aa90 ]

I've accidentally stumbled upon the IS_ENABLED(EXPOLINE_*) lines, which
obviously always evaluate to false. Fix this.

Fixes: f19fbd5ed642 ("s390: introduce execute-trampolines for branches")
Signed-off-by: Eugeniu Rosca <erosca@de.adit-jv.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

KVM: s390: force bp isolation for VSIE

[ Upstream commit f315104ad8b0c32be13eac628569ae707c332cb5 ]

If the guest runs with bp isolation when doing a SIE instruction,
we must also run the nested guest with bp isolation when emulating
that SIE instruction.
This is done by activating BPBC in the lpar, which acts as an override
for lower level guests.

Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Reviewed-by: Janosch Frank <frankja@linux.vnet.ibm.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>