mx5: Register i2c on Freescale MX51 Babbage HW

Add device registration and setup IOMUX pins in the mx51_babbage
board feil.

Signed-off-by: Dinh Nguyen <Dinh.Nguyen@freescale.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

mx5: Add i2c to Freescale MX51 Babbage HW

This patch adds I2C functionality to the Freescale MX51 Babbage HW.
The patch adds device structures, i2c board slave device defines,
IOMUX pin defines, and clocks.

Signed-off-by: Dinh Nguyen <Dinh.Nguyen@freescale.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

arm: mxc: utilise usecount field in clock operations

This patch fixes the clock refcounting when reparenting is used.

Boot-tested on imx51 babbage board.

Sascha pointed out a good explanation of refcounting here:
http://www.spinics.net/lists/arm-kernel/msg85879.html

Signed-off-by: Amit Kucheria <amit.kucheria@canonical.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

mx25pdk: add keypad support

The keymap is taken from the Freescale supplied kernel.

Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

mx25: add platform code for imx-keypad

Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

mxc_nand: add support for platform defined partitions

Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

mxc_nand: Fix OOB handling

The OOB handling in the mxc_nand driver is broken for v1 type
controllers (i.MX27/31) with 512 byte page size. This perhaps
did not show up because ubi does not use OOB.
Update the driver to always read/write a whole page even if
only OOB is requested. With this patch the driver passes the
mtd_oobtest on i.MX27 with 512 byte page size. Also tested
with 2048 byte page size and on i.MX35 (v2 type controller)

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Reported-by: Wolfram Sang <w.sang@pengutronix.de>
Tested-by: Baruch Siach <baruch@tkos.co.il>

eukrea_mbimx27: add audio codec

Signed-off-by: Eric Bénard <eric@eukrea.com>
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

eukrea_mbimx27: add support for the keyboard

Signed-off-by: Eric Bénard <eric@eukrea.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

MX2X: Add Keypad device definition for MX2X arch

Based on work from Alberto Panizzo for MX3X

Signed-off-by: Eric Bénard <eric@eukrea.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

eukrea_mbimx27: use card detect through DAT3 for SDHC1

Signed-off-by: Eric Bénard <eric@eukrea.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

mxcmmc: add card detect through DAT3 possibility

Signed-off-by: Eric Bénard <eric@eukrea.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

mach-cpuimx27: register wdt and w1_master resources

Signed-off-by: Eric Bénard <eric@eukrea.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

mach-cpuimx27: add USB Host2 and OTG support

support copied from mach-pca100.c

Signed-off-by: Eric Bénard <eric@eukrea.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

eukrea_mbimx27: fix ADS7846 support

Signed-off-by: Eric Bénard <eric@eukrea.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

mach-cpuimx27: fix QuadUART's IRQ typo in pins'setup

Signed-off-by: Eric Bénard <eric@eukrea.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

cpuimx27 and mbimx27: allow fine control of UART4 and SDHC2 usage

Signed-off-by: Eric Bénard <eric@eukrea.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

eukrea_mbimx27-baseboard: add timings for DVI output

Signed-off-by: Eric Bénard <eric@eukrea.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

eukrea_mbimx27-baseboard: add generic-bl and platform-lcd controls

Signed-off-by: Eric Bénard <eric@eukrea.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

eukrea_mbimx27-baseboard: fix typo in display name

Signed-off-by: Eric Bénard <eric@eukrea.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

pcm037/pcm043/pca100: fix ULPI-related build warnings

Like this one (if CONFIG_USB_ULPI is not set):

arch/arm/mach-mx3/mach-pcm043.c:312: warning: 'otg_pdata' defined but not used
arch/arm/mach-mx3/mach-pcm043.c:317: warning: 'usbh1_pdata' defined but not used

Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

ARM: mx3: mx31lilly: pass mc13783 SPI IRQ pin

This makes the resistive touch interface work.

Signed-off-by: Daniel Mack <daniel@caiaq.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

ARM: mx3: pcm037: remove unused variable

CC      arch/arm/mach-mx3/mach-pcm037.o
  arch/arm/mach-mx3/mach-pcm037.c: In function 'mxc_board_init':
  arch/arm/mach-mx3/mach-pcm037.c:584: warning: unused variable 'tmp'

Signed-off-by: Daniel Mack <daniel@caiaq.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

Merge git://git./linux/kernel/git/davem/net-2.6

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (63 commits)
  drivers/net/usb/asix.c: Fix pointer cast.
  be2net: Bug fix to avoid disabling bottom half during firmware upgrade.
  proc_dointvec: write a single value
  hso: add support for new products
  Phonet: fix potential use-after-free in pep_sock_close()
  ath9k: remove VEOL support for ad-hoc
  ath9k: change beacon allocation to prefer the first beacon slot
  sock.h: fix kernel-doc warning
  cls_cgroup: Fix build error when built-in
  macvlan: do proper cleanup in macvlan_common_newlink() V2
  be2net: Bug fix in init code in probe
  net/dccp: expansion of error code size
  ath9k: Fix rx of mcast/bcast frames in PS mode with auto sleep
  wireless: fix sta_info.h kernel-doc warnings
  wireless: fix mac80211.h kernel-doc warnings
  iwlwifi: testing the wrong variable in iwl_add_bssid_station()
  ath9k_htc: rare leak in ath9k_hif_usb_alloc_tx_urbs()
  ath9k_htc: dereferencing before check in hif_usb_tx_cb()
  rt2x00: Fix rt2800usb TX descriptor writing.
  rt2x00: Fix failed SLEEP->AWAKE and AWAKE->SLEEP transitions.
  ...

Merge branch 'alpha-next' of git://git./linux/kernel/git/mattst88/alpha-2.6

* 'alpha-next' of git://git.kernel.org/pub/scm/linux/kernel/git/mattst88/alpha-2.6:
  alpha: simplify and optimize sched_find_first_bit
  alpha: invoke oom-killer from page fault
  Convert alpha to use clocksources instead of arch_gettimeoffset

Merge git://git./linux/kernel/git/gregkh/driver-core-2.6

* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core-2.6:
  driver core: add devname module aliases to allow module on-demand auto-loading

Revert "module: drop the lock while waiting for module to complete initialization."

This reverts commit 480b02df3aa9f07d1c7df0cd8be7a5ca73893455, since
Rafael reports that it causes occasional kernel paging request faults in
load_module().

Dropping the module lock and re-taking it deep in the call-chain is
definitely not the right thing to do.  That just turns the mutex from a
lock into a "random non-locking data structure" that doesn't actually
protect what it's supposed to protect.

Requested-and-tested-by: Rafael J. Wysocki <rjw@sisk.pl>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Brandon Philips <brandon@ifup.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

drivers/net/usb/asix.c: Fix pointer cast.

Stephen Rothwell reports the following new warning:

drivers/net/usb/asix.c: In function 'asix_rx_fixup':
drivers/net/usb/asix.c:325: warning: cast from pointer to integer of different size
drivers/net/usb/asix.c:354: warning: cast from pointer to integer of different size

The code just cares about the low alignment bits, so use
an "unsigned long" cast instead of one to "u32".

Signed-off-by: David S. Miller <davem@davemloft.net>

be2net: Bug fix to avoid disabling bottom half during firmware upgrade.

Certain firmware commands/operations to upgrade firmware could take several
seconds to complete. The code presently disables bottom half during these
operations which could lead to unpredictable behaviour in certain cases. This
patch now does all firmware upgrade operations asynchronously using a
completion variable.

Signed-off-by: Sarveshwar Bandi <sarveshwarb@serverengines.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

proc_dointvec: write a single value

The commit 00b7c3395aec3df43de5bd02a3c5a099ca51169f
"sysctl: refactor integer handling proc code"
modified the behaviour of writing to /proc.
Before the commit, write("1\n") to /proc/sys/kernel/printk succeeded. But
now it returns EINVAL.

This commit supports writing a single value to a multi-valued entry.

Signed-off-by: J. R. Okajima <hooanon05@yahoo.co.jp>
Reviewed-and-tested-by: WANG Cong <amwang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

hso: add support for new products

This patch adds a few new product id's for the hso driver.

Signed-off-by: Filip Aben <f.aben@option.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Phonet: fix potential use-after-free in pep_sock_close()

sk_common_release() might destroy our last reference to the socket.
So an extra temporary reference is needed during cleanup.

Signed-off-by: Rémi Denis-Courmont <remi.denis-courmont@nokia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

alpha: simplify and optimize sched_find_first_bit

Search only the first 100 bits instead of 140, saving a couple
instructions. The resulting code is about 1/3 faster (40K ticks/1000
iterations down to 30K ticks/1000 iterations).

Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: linux-alpha@vger.kernel.org
Acked-by: Richard Henderson <rth@twiddle.net>
Signed-off-by: Matt Turner <mattst88@gmail.com>

alpha: invoke oom-killer from page fault

As explained in commit 1c0fe6e3bd, we want to call the architecture
independent oom killer when getting an unexplained OOM from
handle_mm_fault, rather than simply killing current.

[mattst88: kill now unused 'survive' label]
Cc: linux-alpha@vger.kernel.org
Cc: Richard Henderson <rth@twiddle.net>
Cc: linux-arch@vger.kernel.org
Acked-by: David Rientjes <rientjes@google.com>
Signed-off-by: Matt Turner <mattst88@gmail.com>
Signed-off-by: Nick Piggin <npiggin@suse.de>

Convert alpha to use clocksources instead of arch_gettimeoffset

Alpha has a tsc like rpcc counter that it uses to manage time.
This can be converted to an actual clocksource instead of utilizing
the arch_gettimeoffset method that is really only there for legacy
systems with no continuous counter.

Further cleanups could be made if alpha converted to the clockevent
model.

CC: Thomas Gleixner <tglx@linutronix.de>
CC: Richard Henderson <rth@twiddle.net>
Acked-by: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Tested-by: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Signed-off-by: Matt Turner <mattst88@gmail.com>
Signed-off-by: John Stultz <johnstul@us.ibm.com>

driver core: add devname module aliases to allow module on-demand auto-loading

This adds:
  alias: devname:<name>
to some common kernel modules, which will allow the on-demand loading
of the kernel module when the device node is accessed.

Ideally all these modules would be compiled-in, but distros seems too
much in love with their modularization that we need to cover the common
cases with this new facility. It will allow us to remove a bunch of pretty
useless init scripts and modprobes from init scripts.

The static device node aliases will be carried in the module itself. The
program depmod will extract this information to a file in the module directory:
  $ cat /lib/modules/2.6.34-00650-g537b60d-dirty/modules.devname
  # Device nodes to trigger on-demand module loading.
  microcode cpu/microcode c10:184
  fuse fuse c10:229
  ppp_generic ppp c108:0
  tun net/tun c10:200
  dm_mod mapper/control c10:235

Udev will pick up the depmod created file on startup and create all the
static device nodes which the kernel modules specify, so that these modules
get automatically loaded when the device node is accessed:
  $ /sbin/udevd --debug
  ...
  static_dev_create_from_modules: mknod '/dev/cpu/microcode' c10:184
  static_dev_create_from_modules: mknod '/dev/fuse' c10:229
  static_dev_create_from_modules: mknod '/dev/ppp' c108:0
  static_dev_create_from_modules: mknod '/dev/net/tun' c10:200
  static_dev_create_from_modules: mknod '/dev/mapper/control' c10:235
  udev_rules_apply_static_dev_perms: chmod '/dev/net/tun' 0666
  udev_rules_apply_static_dev_perms: chmod '/dev/fuse' 0666

A few device nodes are switched to statically allocated numbers, to allow
the static nodes to work. This might also useful for systems which still run
a plain static /dev, which is completely unsafe to use with any dynamic minor
numbers.

Note:
The devname aliases must be limited to the *common* and *single*instance*
device nodes, like the misc devices, and never be used for conceptually limited
systems like the loop devices, which should rather get fixed properly and get a
control node for losetup to talk to, instead of creating a random number of
device nodes in advance, regardless if they are ever used.

This facility is to hide the mess distros are creating with too modualized
kernels, and just to hide that these modules are not compiled-in, and not to
paper-over broken concepts. Thanks! :)

Cc: Greg Kroah-Hartman <gregkh@suse.de>
Cc: David S. Miller <davem@davemloft.net>
Cc: Miklos Szeredi <miklos@szeredi.hu>
Cc: Chris Mason <chris.mason@oracle.com>
Cc: Alasdair G Kergon <agk@redhat.com>
Cc: Tigran Aivazian <tigran@aivazian.fsnet.co.uk>
Cc: Ian Kent <raven@themaw.net>
Signed-Off-By: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Merge branch 'wimax-2.6.35.y' of git://git./linux/kernel/git/inaky/wimax

Merge branch 'master' of git://git./linux/kernel/git/linville/wireless-2.6

Merge branch 'devel' of /home/rmk/linux-2.6-arm

* 'devel' of master.kernel.org:/home/rmk/linux-2.6-arm: (103 commits)
  ARM: 6141/1: Add audio support part in arch/arm/mach-w90x900
  ARM: 5939/1: ARM: Add option CMDLINE_FORCE to force usage of the in-kernel cmdline
  ARM: 6140/1: silence a bogus sparse warning in unwind.c
  ARM: mach-at91: duplicated include
  ARM: arch/arm/nwfpe/fpsr.h: Checkpatch cleanup
  ARM: arch/arm/mach-shark/pci.c: Checkpatch cleanup
  ARM: arch/arm/nwfpe/ChangeLog: Checkpatch cleanup
  ARM: arch/arm/mach-sa1100/leds.c: Checkpatch cleanup
  ARM: arch/arm/mach-h720x/common.h: Checkpatch cleanup
  ARM: arch/arm/mach-footbridge/ebsa285-pci.c: Checkpatch cleanup
  ARM: arch/arm/mach-clps711x/Makefile.boot: Checkpatch cleanup
  ARM: arch/arm/boot/bootp/bootp.lds: Checkpatch cleanup
  ARM: SPEAR6xx: remove duplicated #include
  ARM: s3c6400_defconfig: Add NAND driver
  ARM: s3c6400_defconfig: enable sound as modules
  ARM: s3c6400_defconfig: enable power management
  ARM: s5pv210_defconfig: Update s5pv210_defconfig to v2.6.34
  ARM: s5pc110_defconfig: Update s5pc110_defconfig to v2.6.34
  ARM: s5p6442_defconfig: Update s5p6442_defconfig to v2.6.34
  ARM: s5p6440_defconfig: Update s5p6440_defconfig to v2.6.34
  ...

Merge branch 'for-linus' of git://git./linux/kernel/git/roland/infiniband

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband:
  RDMA/nes: Fix incorrect unlock in nes_process_mac_intr()
  RDMA/nes: Async event for closed QP causes crash
  RDMA/nes: Have ethtool read hardware registers for rx/tx stats
  RDMA/cxgb4: Only insert sq qid in lookup table
  RDMA/cxgb4: Support IB_WR_READ_WITH_INV opcode
  RDMA/cxgb4: Set fence flag for inv-local-stag work requests
  RDMA/cxgb4: Update some HW limits
  RDMA/cxgb4: Don't limit fastreg page list depth
  RDMA/cxgb4: Return proper errors in fastreg mr/pbl allocation
  RDMA/cxgb4: Fix overflow bug in CQ arm
  RDMA/cxgb4: Optimize CQ overflow detection
  RDMA/cxgb4: CQ size must be IQ size - 2
  RDMA/cxgb4: Register RDMA provider based on LLD state_change events
  RDMA/cxgb4: Detach from the LLD after unregistering RDMA device
  IB/ipath: Remove support for QLogic PCIe QLE devices
  IB/qib: Add new qib driver for QLogic PCIe InfiniBand adapters
  IB/mad: Make needlessly global mad_sendq_size/mad_recvq_size static
  IB/core: Allow device-specific per-port sysfs files
  mlx4_core: Clean up mlx4_alloc_icm() a bit
  mlx4_core: Fix possible chunk sg list overflow in mlx4_alloc_icm()

Merge branch 'next-spi' of git://git.secretlab.ca/git/linux-2.6

* 'next-spi' of git://git.secretlab.ca/git/linux-2.6:
  spi/xilinx: Fix compile error
  spi/davinci: Fix clock prescale factor computation
  spi: move bitbang txrx utility functions to private header
  spi/mpc5121: Add SPI master driver for MPC5121 PSC
  powerpc/mpc5121: move PSC FIFO memory init to platform code
  spi/ep93xx: implemented driver for Cirrus EP93xx SPI controller
  Documentation/spi/* compile warning fix
  spi/omap2_mcspi: Check params before dereference or use
  spi/omap2_mcspi: add turbo mode support
  spi/omap2_mcspi: change default DMA_MIN_BYTES value to 160
  spi/pl022: fix stop queue procedure
  spi/pl022: add support for the PL023 derivate
  spi/pl022: fix up differences between ARM and ST versions
  spi/spi_mpc8xxx: Do not use map_tx_dma to unmap rx_dma
  spi/spi_mpc8xxx: Fix QE mode Litte Endian
  spi/spi_mpc8xxx: fix potential memory corruption.

Merge branch 'for-linus' of git://git./linux/kernel/git/gerg/m68knommu

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/gerg/m68knommu:
  arch/m68knommu/platform/68360/commproc.c: Checkpatch cleanup
  arch/m68knommu/mm/fault.c: Checkpatch cleanup
  m68knommu: improve short help of m68knommu/Kconfig/RAMSIZE for '0' case
  m68knommu: remove un-used mcfsmc.h
  m68knommu: add smc91x support for ColdFire NETtel boards
  m68knommu: add smc91x support to ColdFire 5249 platform
  m68knommu: remove size limit on non-MMU TASK_SIZE
  m68knommu: fix broken use of BUAD_TABLE_SIZE in 68328serial driver
  m68knommu: Coldfire QSPI platform support

Merge branch 'for-linus' of git://git./linux/kernel/git/lrg/voltage-2.6

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/lrg/voltage-2.6:
  regulator: return set_mode is same mode is requested
  Regulators: ab3100/bq24022: add a missing .owner field in regulator_desc
  twl6030: regulator: Remove vsel tables and use formula for calculation
  mc13783-regulator: fix vaild voltage range checking for mc13783_fixed_regulator_set_voltage
  regulator: use voltage number array in 88pm860x
  regulator: make 88pm860x sharing one driver structure
  regulator: simplify regulator_register() error handling
  regulator: fix unset_regulator_supplies() to remove all matches
  regulator: prevent registration of matching regulator consumer supplies
  regulator: Allow regulator-regulator supplies to be specified by name

Merge git://git./linux/kernel/git/wim/linux-2.6-watchdog

* git://git.kernel.org/pub/scm/linux/kernel/git/wim/linux-2.6-watchdog:
  watchdog: Driver for the watchdog timer on Freescale IMX2 (and later) processors.
  watchdog: s3c2410_wdt - Fix on handling of the request_mem_region fail
  watchdog: s3c2410_wdt - Add extra option to include watchdog for Samsung SoCs
  iTCO_wdt: fix TCO V1 timeout values and limits
  watchdog: twl4030_wdt: Disable watchdog during probing
  watchdog: update/improve/consolidate watchdog driver
  watchdog: booke_wdt: fix ioctl status flags
  watchdog: fix several MODULE_PARM_DESC strings
  watchdog: bfin: use new common Blackfin watchdog header

Merge branches 'cxgb4', 'misc', 'mlx4', 'nes' and 'qib' into for-next

RDMA/nes: Fix incorrect unlock in nes_process_mac_intr()

Commit ce6e74f2 ("RDMA/nes: Make nesadapter->phy_lock usage
consistent") introduced a problem where phy_lock was only unlocked
within an if statement and so nes_process_mac_intr() could return with
phy_lock still held.  Fix this.

This was discovered because of the sparse warning:

    drivers/infiniband/hw/nes/nes_hw.c:2643:9: warning: context imbalance in 'nes_process_mac_intr' - different lock contexts for basic block

Reported-by: Roland Dreier <rdreier@cisco.com>
Signed-off-by: Chien Tung <chien.tin.tung@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>

Merge git://git./linux/kernel/git/steve/gfs2-2.6-fixes

* git://git.kernel.org/pub/scm/linux/kernel/git/steve/gfs2-2.6-fixes:
  GFS2: Fix permissions checking for setflags ioctl()
  GFS2: Don't "get" xattrs for ACLs when ACLs are turned off
  GFS2: Rework reclaiming unlinked dinodes

Merge branch 'for-linus' of git://oss.sgi.com/xfs/xfs

* 'for-linus' of git://oss.sgi.com/xfs/xfs:
  xfs: Ensure inode allocation buffers are fully replayed
  xfs: enable background pushing of the CIL
  xfs: forced unmounts need to push the CIL
  xfs: Introduce delayed logging core code
  xfs: Delayed logging design documentation
  xfs: Improve scalability of busy extent tracking
  xfs: make the log ticket ID available outside the log infrastructure
  xfs: clean up log ticket overrun debug output
  xfs: Clean up XFS_BLI_* flag namespace
  xfs: modify buffer item reference counting
  xfs: allow log ticket allocation to take allocation flags
  xfs: Don't reuse the same transaction ID for duplicated transactions.

Merge git://git.infradead.org/battery-2.6

* git://git.infradead.org/battery-2.6:
  power_supply: Fix regression for 'type' property

ath9k: remove VEOL support for ad-hoc

With VEOL, Beacon transmission in ad-hoc does not currently work.
I believe for larger ad-hoc networks, VEOL is too unreliable, as
it can get beacon transmissions stuck during synchronization.
Use SWBA based beacon trasmission similar to AP mode instead.

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Acked-by: Benoit Papillault <benoit.papillault@free.fr>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: change beacon allocation to prefer the first beacon slot

This fixes IBSS beacon transmissions without VEOL enabled

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

auxdisplay: section cleanup in cfag12864bfb driver

This fixes a two section mismatches and makes remove() __devexit.

Signed-off-by: Henrik Kretzschmar <henne@nachtwindheim.de>
Cc: Miguel Ojeda Sandonis <miguel.ojeda.sandonis@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

nuc900fb: release correct mem region

We should be releasing "res->start" here.

Signed-off-by: Dan Carpenter <error27@gmail.com>
Acked-by: Wan ZongShun <mcuos.com@gmail.com>
Cc: Wang Qiang <rurality.linux@gmail.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

fb_defio: fix for non-dirty ptes

Fix a problem observed while using fb_defio with a short delay on a
PowerPC platform.

It is possible that page_mkclean() is invoked in the deferred io work
function _before_ a PTE has been marked dirty.  In this case, the page is
removed from the defio pagelist but page_mkclean() does not write-protect
the page again.  The end result is that defio ignores all subsequent
writes to the page and the corresponding portions of the framebuffer never
get updated.

The fix consists in keeping track of the pages with non-dirty PTEs,
re-checking them again on the next deferred io work iteration.  Note that
those pages are not passed to the defio callback as they are not written
by userspace yet.

Signed-off-by: Albert Herranz <albert_herranz@yahoo.es>
Acked-by: Jaya Kumar <jayakumar.lkml@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

sgivwfb: fix sections

Since the drivers probe call was changed from .init.text to .devinit.text
in commit c2e13037e6794bd0d9de3f9ecabf5615f15c160b ("platform-drivers:
move probe to .devinit.text in drivers/video") the fb_fix_screeninfo and
fb_var_screeninfo structures must be changed from .init.data to
.devinit.data, too.

Also the drivers remove routine should be moved from .text to .devexit.text

It removes these 7 section mismatch warnings from modpost:

WARNING: vmlinux.o(.devinit.text+0x1e28): Section mismatch in reference from the function sgivwfb_probe() to the variable .init.data:sgivwfb_fix
The function __devinit sgivwfb_probe() references
a variable __initdata sgivwfb_fix.
If sgivwfb_fix is only used by sgivwfb_probe then
annotate sgivwfb_fix with a matching annotation.

WARNING: vmlinux.o(.devinit.text+0x1e50): Section mismatch in reference from the function sgivwfb_probe() to the (unknown reference) .init.data:(unknown)
The function __devinit sgivwfb_probe() references
a (unknown reference) __initdata (unknown).
If (unknown) is only used by sgivwfb_probe then
annotate (unknown) with a matching annotation.

WARNING: vmlinux.o(.devinit.text+0x1e59): Section mismatch in reference from the function sgivwfb_probe() to the (unknown reference) .init.data:(unknown)
The function __devinit sgivwfb_probe() references
a (unknown reference) __initdata (unknown).
If (unknown) is only used by sgivwfb_probe then
annotate (unknown) with a matching annotation.

WARNING: vmlinux.o(.devinit.text+0x1e60): Section mismatch in reference from the function sgivwfb_probe() to the variable .init.data:sgivwfb_fix
The function __devinit sgivwfb_probe() references
a variable __initdata sgivwfb_fix.
If sgivwfb_fix is only used by sgivwfb_probe then
annotate sgivwfb_fix with a matching annotation.

WARNING: vmlinux.o(.devinit.text+0x1e6a): Section mismatch in reference from the function sgivwfb_probe() to the (unknown reference) .init.data:(unknown)
The function __devinit sgivwfb_probe() references
a (unknown reference) __initdata (unknown).
If (unknown) is only used by sgivwfb_probe then
annotate (unknown) with a matching annotation.

WARNING: vmlinux.o(.devinit.text+0x1e7f): Section mismatch in reference from the function sgivwfb_probe() to the variable .init.data:sgivwfb_var1600sw
The function __devinit sgivwfb_probe() references
a variable __initdata sgivwfb_var1600sw.
If sgivwfb_var1600sw is only used by sgivwfb_probe then
annotate sgivwfb_var1600sw with a matching annotation.

WARNING: vmlinux.o(.devinit.text+0x1e91): Section mismatch in reference from the function sgivwfb_probe() to the variable .init.data:sgivwfb_var
The function __devinit sgivwfb_probe() references
a variable __initdata sgivwfb_var.
If sgivwfb_var is only used by sgivwfb_probe then
annotate sgivwfb_var with a matching annotation.

Signed-off-by: Henrik Kretzschmar <henne@nachtwindheim.de>
Cc: Arnaud Patard <arnaud.patard@rtp-net.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

s3c2410fb: fix sections

Since the drivers probe calls were changed from .init.text to
.devinit.text in commit c2e13037e6794bd0d9de3f9ecabf5615f15c160b
("platform-drivers: move probe to .devinit.text in drivers/video") all the
function from .init.text should be moved to .devinit.text, too.

The drivers remove calls can also be move from .text to .devexit.text.

Signed-off-by: Henrik Kretzschmar <henne@nachtwindheim.de>
Cc: Vincent Sanders <support@simtec.co.uk>
Acked-by: Arnaud Patard <arnaud.patard@rtp-net.org>
Tested-by: Arnaud Patard <arnaud.patard@rtp-net.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

hitfb: fix sections

Since the drivers probe call was changed from .init.text to .devinit.text
in commit c2e13037e6794bd0d9de3f9ecabf5615f15c160b ("platform-drivers:
move probe to .devinit.text in drivers/video") the fb_fix_screeninfo and
fb_var_screeninfo structures must be changed from .init.data to
.devinit.data, too.

Also the drivers remove routine should be moved from .exit.text to
.devexit.text

Signed-off-by: Henrik Kretzschmar <henne@nachtwindheim.de>
Cc: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

fbdev: move FBIO_WAITFORVSYNC to linux/fb.h

FBIO_WAITFORVSYNC is currently implemented by matroxfb, atyfb, intelfb and
more.  All of them keep redefining the same FBIO_WAITFORVSYNC macro over
and over again, so move it to linux/fb.h and clean up those duplicate
defines.

Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Cc: Ville Syrjala <syrjala@sci.fi>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Maik Broemme <mbroemme@plusserver.de>
Cc: Petr Vandrovec <vandrove@vc.cvut.cz>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Krzysztof Helt <krzysztof.h1@poczta.fm>
Cc: "Hiremath, Vaibhav" <hvaibhav@ti.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

fbdev: da8xx/omap-l1xx: implement double buffering

This work includes the following:

- Implement handler for FBIO_WAITFORVSYNC ioctl.

- Allocate the data and palette buffers separately.  A consequence of
  this is that the palette and data loading is now done in different
  phases.  And that the LCD must be disabled temporarily after the palette
  is loaded but this will only happen once after init and each time the
  palette is changed.  I think this is OK.

- Allocate two (ping and pong) framebuffers from memory.

- Add pan_display handler which toggles the LCDC DMA registers between
  the ping and pong buffers.

Signed-off-by: Martin Ambrose <martin@ti.com>
Cc: Chaithrika U S <chaithrika@ti.com>
Cc: Sudhakar Rajashekhara <sudhakar.raj@ti.com>
Cc: Krzysztof Helt <krzysztof.h1@poczta.fm>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

fbdev: section cleanup in w100fb

Fix up the section in the w100fb driver, by moving:

* w100fb_remove() from .text to .devexit.text

* w100_get_xtal_table() from .text to .devinit.text

* w100fb_init() from .devinit.text to .init.text

Signed-off-by: Henrik Kretzschmar <henne@nachtwindheim.de>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Cc: <stable@kernel.org> [if "platform-drivers: move probe to .devinit.text in drivers/video" was merged]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

fbdev: section cleanup in vga16fb

Fix up the sections in the vga16fb driver, by moving:

* the variables vga16_defined and vga16fb
from .init.data to .devinit.data

* vga16fb_setup() from .text to .init.text

* vga16fb_remove() from .text. to .devexit.text

This fixes the following warnings issued by modpost:

WARNING: drivers/video/built-in.o(.devinit.text+0x1a420): Section mismatch in re
ference from the function vga16fb_probe() to the (unknown reference) .init.data:
(unknown)
The function __devinit vga16fb_probe() references
a (unknown reference) __initdata (unknown).
If (unknown) is only used by vga16fb_probe then
annotate (unknown) with a matching annotation.

WARNING: drivers/video/built-in.o(.devinit.text+0x1a437): Section mismatch in reference from the function vga16fb_probe() to the variable .init.data:vga16fb_defined
The function __devinit vga16fb_probe() references
a variable __initdata vga16fb_defined.
If vga16fb_defined is only used by vga16fb_probe then
annotate vga16fb_defined with a matching annotation.

WARNING: drivers/video/built-in.o(.devinit.text+0x1a457): Section mismatch in reference from the function vga16fb_probe() to the variable .init.data:vga16fb_fix
The function __devinit vga16fb_probe() references
a variable __initdata vga16fb_fix.
If vga16fb_fix is only used by vga16fb_probe then
annotate vga16fb_fix with a matching annotation.

Signed-off-by: Henrik Kretzschmar <henne@nachtwindheim.de>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Cc: <stable@kernel.org> [if "platform-drivers: move probe to .devinit.text in drivers/video" was merged]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

fbdev: section cleanup in vfb

Fix up the section in the vfb driver, by moving the variables vfb_default
and vfb_fix from .init.data to .devinit.data

This fixes the following warnings issued by modpost:

WARNING: drivers/video/vfb.o(.devinit.text+0xf8): Section mismatch in reference from the function vfb_probe() to the variable .init.data:vfb_default
The function __devinit vfb_probe() references
a variable __initdata vfb_default.
If vfb_default is only used by vfb_probe then
annotate vfb_default with a matching annotation.

WARNING: drivers/video/vfb.o(.devinit.text+0x114): Section mismatch in reference from the function vfb_probe() to the variable .init.data:vfb_fix
The function __devinit vfb_probe() references
a variable __initdata vfb_fix.
If vfb_fix is only used by vfb_probe then
annotate vfb_fix with a matching annotation.

Signed-off-by: Henrik Kretzschmar <henne@nachtwindheim.de>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Cc: <stable@kernel.org> [if "platform-drivers: move probe to .devinit.text in drivers/video" was merged]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

fbdev: section cleanup in hgafb

Fix up the sections in the hgafb driver, by

* moving hga_default_var and hga_fix from .init.data to .devinit.data

* moving hga_detect() from .init.text to .devinit.text

* moving hga_fb_remove() from .text to .devexit.text

This fixes the following warnings issued by modpost:

WARNING: drivers/video/hgafb.o(.devinit.text+0x18): Section mismatch in referenc
e from the function hgafb_probe() to the function .init.text:hga_card_detect()
The function __devinit hgafb_probe() references
a function __init hga_card_detect().
If hga_card_detect is only used by hgafb_probe then
annotate hga_card_detect with a matching annotation.

WARNING: drivers/video/hgafb.o(.devinit.text+0xfe): Section mismatch in referenc
e from the function hgafb_probe() to the variable .init.data:hga_fix
The function __devinit hgafb_probe() references
a variable __initdata hga_fix.
If hga_fix is only used by hgafb_probe then
annotate hga_fix with a matching annotation.

WARNING: drivers/video/hgafb.o(.devinit.text+0x105): Section mismatch in reference from the function hgafb_probe() to the variable .init.data:hga_default_var
The function __devinit hgafb_probe() references
a variable __initdata hga_default_var.
If hga_default_var is only used by hgafb_probe then
annotate hga_default_var with a matching annotation.

Signed-off-by: Henrik Kretzschmar <henne@nachtwindheim.de>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Cc: <stable@kernel.org> [if "platform-drivers: move probe to .devinit.text in drivers/video" was merged]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

fbdev: section cleanup in arcfb

Fix the sections in the arcfb driver, by moving:

* the variables arcfb_fix and arcfb_var from .init.data to .devinit.data

* arcfb_remove() from .text to .devexit.text

This fixes the following warnings issued by modpost:

WARNING: drivers/video/built-in.o(.devinit.text+0x543): Section mismatch in reference from the function arcfb_probe() to the variable .init.data:arcfb_var
The function __devinit arcfb_probe() references
a variable __initdata arcfb_var.
If arcfb_var is only used by arcfb_probe then
annotate arcfb_var with a matching annotation.

WARNING: drivers/video/built-in.o(.devinit.text+0x558): Section mismatch in reference from the function arcfb_probe() to the variable .init.data:arcfb_fix
The function __devinit arcfb_probe() references
a variable __initdata arcfb_fix.
If arcfb_fix is only used by arcfb_probe then
annotate arcfb_fix with a matching annotation.

Signed-off-by: Henrik Kretzschmar <henne@nachtwindheim.de>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Cc: <stable@kernel.org> [if "platform-drivers: move probe to .devinit.text in drivers/video" was merged]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

sis: strcpy() => strlcpy()

These are different size buffers (40 chars vs 16), we may as well be
cautious.

Signed-off-by: Dan Carpenter <error27@gmail.com>
Cc: Thomas Winischhofer <thomas@winischhofer.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

fbdev: bfin-lq035q1-fb: respect new PPI mode platform field

This lets us support the new BF527-EZKIT V2.1 via platform resources
tweaks only.

Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Cc: Bryan Wu <cooloney@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

rtc: use genirq directly in rtc-wm831x

Now that the WM831x core uses genirq for the IRQ controller there is no
need to use the WM831x-specific wrappers to request interrupts so convert
to use genirq directly.

Also use more meaningful strings to make /proc/interrupts more readily
legible.

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

rtc-cmos: do dev_set_drvdata() earlier in the initialization

The bug is an oops when dev_get_drvdata() returned null in
cmos_update_irq_enable().  The call tree looks like this:
  rtc_dev_ioctl()
    => rtc_update_irq_enable()
      => cmos_update_irq_enable()

It's caused by a race condition in the module initialization.  It is
rtc_device_register() which makes the ioctl operations live so I moved
the call to dev_set_drvdata() before the call to rtc_device_register().

Addresses https://bugzilla.kernel.org/show_bug.cgi?id=15963

Reported-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Dan Carpenter <error27@gmail.com>
Tested-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Paul Gortmaker <p_gortmaker@yahoo.com>
Cc: Malte Schroder <maltesch@gmx.de>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Herton Ronaldo Krzesinski <herton@mandriva.com.br>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

rtc-ds1302: add some abstraction for new platform support

The current ds1302 driver (or at least the one that lives in /drivers/rtc)
seems to be designed for memory mapped devices only.  This make it quite
hard to add support for GPIO-based implementations (as this is the case
for the upcoming Arcom Vulcan).

This patch moves the direct register access to inline functions with
explicit names.  Still not as good as a proper platform driver, but at
least neater.

Signed-off-by: Marc Zyngier <maz@misterjones.org>
Cc: Paul Gortmaker <p_gortmaker@yahoo.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

rtc-isl1208: use sysfs_{create/remove}_group

Instead of individually creating and removing the sysfs device attribute
files, wrap them in an attribute_group and use
sysfs_{create/remove}_group.

Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Paul Gortmaker <p_gortmaker@yahoo.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

rtc-mxc: remove unnecessary clock source for rtc subsystem

On imx SoCs rtc clock parent is CKIL, but clock rate shall be determined
using rtc clock itself, that eliminates CKIL clock usage in the driver.

Signed-off-by: Vladimir Zapolskiy <vzapolskiy@gmail.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Daniel Mack <daniel@caiaq.de>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Paul Gortmaker <p_gortmaker@yahoo.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

s3c rtc driver: add support for S3C64xx

Add support for the S3C64xx SoC to the generic S3C RTC driver.

Signed-off-by: Maurus Cuelenaere <mcuelenaere@gmail.com>
Acked-by: Ben Dooks <ben-linux@fluff.org>
Cc: Frans Pop <elendil@planet.nl>
Cc: Paul Gortmaker <p_gortmaker@yahoo.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

smbfs: remove duplicated #include

Remove duplicated #include('s) in fs/smbfs/symlink.c

Signed-off-by: Huang Weiyi <weiyi.huang@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

xen: fix build when SYSRQ is disabled

Fix build error when CONFIG_MAGIC_SYSRQ is not enabled:

drivers/xen/manage.c:223: error: implicit declaration of function 'handle_sysrq'

Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Acked-by: Jeremy Fitzhardinge <jeremy@xensource.com>
Cc: Chris Wright <chrisw@sous-sol.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

drivers/hwmon/coretemp.c: get TjMax value from MSR

The MSR IA32_TEMPERATURE_TARGET contains the TjMax value in the newer
Intel processors.

Signed-off-by: Huaxu Wan <huaxu.wan@linux.intel.com>
Signed-off-by: Carsten Emde <C.Emde@osadl.org>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: Valdis Kletnieks <valdis.kletnieks@vt.edu>
Cc: Henrique de Moraes Holschuh <hmh@hmh.eng.br>
Cc: Yong Wang <yong.y.wang@linux.intel.com>
Cc: Rudolf Marek <r.marek@assembler.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

drivers/hwmon/coretemp.c: detect the thermal sensors by CPUID

The thermal sensors of Intel(R) CPUs can be detected by CPUID instruction,
indicated by CPUID.06H.EAX[0].

Signed-off-by: Huaxu Wan <huaxu.wan@linux.intel.com>
Signed-off-by: Carsten Emde <C.Emde@osadl.org>
Reviewed-by: Valdis Kletnieks <valdis.kletnieks@vt.edu>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: Henrique de Moraes Holschuh <hmh@hmh.eng.br>
Cc: Yong Wang <yong.y.wang@linux.intel.com>
Cc: Rudolf Marek <r.marek@assembler.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

hwmon: add TI ads7871 a/d converter driver

[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Paul Thomas <pthomas8589@gmail.com>
Cc: Jonathan Cameron <jic23@cam.ac.uk>
Cc: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

lis3: setup poll interval limits

Set valid adjustment window (0 - 2000ms).

Signed-off-by: Samu Onkalo <samu.p.onkalo@nokia.com>
Acked-by: Eric Piel <eric.piel@tremplin-utc.net>
Cc: Daniel Mack <daniel@caiaq.de>
Cc: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

lis3: interrupt handlers for 8bit wakeup and click events

Content for the 8bit device threaded interrupt handlers.  Depending on the
interrupt line and chip configuration, either click or wakeup / freefall
handler is called.  In case of click, BTN_ event is sent via input device.
 In case of wakeup or freefall, input device ABS_ events are updated
immediatelly.

It is still possible to configure interrupt line 1 for fast freefall
detection and use the second line either for click or threshold based
interrupts.  Or both lines can be used for click / threshold interrupts.

Polled input device can be set to stopped state and still get coordinate
updates via input device using interrupt based method.  Polled mode and
interrupt mode can also be used parallel.

BTN_ events are remapped based on existing axis remapping information.

Signed-off-by: Samu Onkalo <samu.p.onkalo@nokia.com>
Acked-by: Eric Piel <eric.piel@tremplin-utc.net>
Cc: Daniel Mack <daniel@caiaq.de>
Cc: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

lis3: add skeletons for interrupt handlers

Original lis3 driver didn't provide interrupt handler(s) for click or
threshold event handling.  This patch adds threaded handlers for one or
two interrupt lines for 8 bit device.  Actual content for interrupt
handling is provided in the separate patch.

Signed-off-by: Samu Onkalo <samu.p.onkalo@nokia.com>
Tested-by: Daniel Mack <daniel@caiaq.de>
Acked-by: Eric Piel <eric.piel@tremplin-utc.net>
Cc: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

lis3: introduce platform data for second ff / wu unit

8 bit device has two wakeup / free fall units.  It was not possible to
configure the second unit.  This patch introduces configuration entry to
the platform data and also corresponding changes to the 8 bit setup
function.

High pass filters were enabled by default.  Patch introduces configuration
option for high pass filter cut off frequency and also possibility to
disable or enable the filter via platform data.  Since the control is a
new one and default state was filter enabled, new option is used to
disable the filter.  This way old platform data is still compatible with
the change.

Signed-off-by: Samu Onkalo <samu.p.onkalo@nokia.com>
Acked-by: Eric Piel <eric.piel@tremplin-utc.net>
Tested-by: Daniel Mack <daniel@caiaq.de>
Cc: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

lis3: separate configuration function for 8 bit device

Separate configuration function for 8 bit version of the chip.  This way
generic part of the init function stays little bit more readable.

Signed-off-by: Samu Onkalo <samu.p.onkalo@nokia.com>
Acked-by: Eric Piel <eric.piel@tremplin-utc.net>
Tested-by: Daniel Mack <daniel@caiaq.de>
Cc: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

lis3: add missing constants for 8bit device

Definitions for click were missing.

Signed-off-by: Samu Onkalo <samu.p.onkalo@nokia.com>
Acked-by: Eric Piel <eric.piel@tremplin-utc.net>
Tested-by: Daniel Mack <daniel@caiaq.de>
Cc: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

crc32: use __BYTE_ORDER macro for endian detection.

Since crc32.c contains a nifty test program that can be executed in user
space, make sure endian detection works reliably in user space too.

Signed-off-by: Joakim Tjernlund <Joakim.Tjernlund@transmode.se>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

crc32: major optimization

Precompute more crc32 values(0xcc00, 0xcc0000 and 0xcc000000) into tables.
 This increases the table size from 1KB to 4KB but the performance benfit
makes it worth it:

28% faster on MPC8321, 266 MHz
2x faster on Core 2 Duo, 3.1GHz

[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Joakim Tjernlund <Joakim.Tjernlund@transmode.se>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

checkpatch: warn on declaration with storage class not at the beginning

The C99 specification states in section 6.11.5:

The placement of a storage-class specifier other than at the beginning
of the declaration specifiers in a declaration is an obsolescent
feature.

Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Acked-by: Jean Delvare <khali@linux-fr.org>
Cc: Andy Whitcroft <apw@shadowen.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

checkpatch: add check for too short Kconfig descriptions

I've seen various new Kconfigs with rather unhelpful one liner
descriptions.  Add a Kconfig warning for a minimum length of the Kconfig
help section.

Right now I arbitarily chose 4. The exact value can be debated.

[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Cc: Andy Whitcroft <apw@shadowen.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

drivers: acpi: don't use own implementation of hex_to_bin()

Remove own implementation of hex_to_bin().

Signed-off-by: Andy Shevchenko <ext-andriy.shevchenko@nokia.com>
Cc: Len Brown <lenb@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

drivers: wireless: use new hex_to_bin() method

Instead of using own implementation involve hex_to_bin() function.

Signed-off-by: Andy Shevchenko <ext-andriy.shevchenko@nokia.com>
Acked-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

fs: ldm: don't use own implementation of hex_to_bin()

Remove own implementation of hex_to_bin().

Signed-off-by: Andy Shevchenko <ext-andriy.shevchenko@nokia.com>
Cc: "Richard Russon (FlatCap)" <ldm@flatcap.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

staging: rt2860: use new hex_to_bin() method

Instead of using own implementation involve hex_to_bin() function.

Signed-off-by: Andy Shevchenko <ext-andriy.shevchenko@nokia.com>
Cc: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

sysctl: don't use own implementation of hex_to_bin()

Remove own implementation of hex_to_bin().

Signed-off-by: Andy Shevchenko <ext-andriy.shevchenko@nokia.com>
Cc: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

usb: atm: speedtch: use new hex_to_bin() method

Instead of using own implementation which potentialy has bugs involve
hex_to_bin() function.  It requires to have hex_to_bin() implementation
introduced by starter patch in series.

Signed-off-by: Andy Shevchenko <ext-andriy.shevchenko@nokia.com>
Cc: Duncan Sands <duncan.sands@free.fr>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

drivers: isdn: use new hex_to_bin() method

Remove own implementation of hex_to_bin().

Signed-off-by: Andy Shevchenko <ext-andriy.shevchenko@nokia.com>
Acked-by: Tilman Schmidt <tilman@imap.cc>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

lib: introduce common method to convert hex digits

hex_to_bin() is a little method which converts hex digit to its actual
value.  There are plenty of places where such functionality is needed.

[akpm@linux-foundation.org: use tolower(), saving 3 bytes, test the more common case first - it's quicker]
[akpm@linux-foundation.org: relocate tolower to make it even faster! (Joe)]
Signed-off-by: Andy Shevchenko <ext-andriy.shevchenko@nokia.com>
Cc: Tilman Schmidt <tilman@imap.cc>
Cc: Duncan Sands <duncan.sands@free.fr>
Cc: Eric W. Biederman <ebiederm@xmission.com>
Cc: Greg Kroah-Hartman <gregkh@suse.de>
Cc: "Richard Russon (FlatCap)" <ldm@flatcap.org>
Cc: John W. Linville <linville@tuxdriver.com>
Cc: Len Brown <lenb@kernel.org>
Cc: Joe Perches <joe@perches.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

lib/hexdump.c: reduce stack variable size and cleanups

Reduce char linebuf[200] to the actual size required., which is 32 * 3 + 2
+ 32 + 1, ie: linebuf[131].

Change examples to use bool true not int 1.

Align multiline argument indentation to open parenthesis.

Use temporary for ptr[j] so trigraph fits on single line.

Convert printk ptr from %*p, (int)(2 * sizeof(void *)) to %p as %p uses
the same calculation for size.

Signed-off-by: Joe Perches <joe@perches.com>
Cc: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

DYNAMIC_DEBUG: fix documentation errors

[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Florian Ragwitz <rafl@debian.org>
Cc: Jason Baron <jbaron@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

dynamic_debug: small cleanup in ddebug_proc_write()

This doesn't change behavior at all.  In the original code, if nwords was
zero then ddebug_parse_query() would return -EINVAL, now we just do it
earlier.

Signed-off-by: Dan Carpenter <error27@gmail.com>
Acked-by: Jason Baron <jbaron@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

scripts/get_maintainer.pl: default to not include unspecified tags

This changes the default of the option --git-all-signature-types to be
disabled by default.

The effect being, that only certain (currently Signed-Off-By:, Acked-by:
and Reviewed-By:) tags are used to get adresses of potential maintainers.

Motivated is this change by the desire to not 'spam' people unnecessary: A
Tested-By or a Reported-By is not ment as a hint that those people want
to/are able to review patches to the code in question.

In a quest to find resilient statistics for this i came up with this:

I produced a list of all the tag-signers not already covered with a
signed-off/acked/reviewed tag somewhere in the last year of git history.

Those were 650 addresses of "assumed non-developers".

And to check if those "assumed non-developers" are professional
testers/reporters worth cc'ing, i then counted their total appearences
in the git log:

469 were mentioned only once.
123 were mentioned twice.
38 three times
8 four times
5 six times
5 five times
1 eight times
1 fourteen times

I believe this supports my thesis, that the ''non-maintainer-tags'' are
not actively useful for patch-review.  (except probably the guy mentioned
fourteen times...)

But of course one could also find arguments to poke holes in this
statistics, for example does this statistic not include code-locality: A
tested-by on a patch that touches some specific piece of code can be more
worth than a signed-off in another part of the tree.

But...  let's play it safe and let's err on the "safe" side meaning to not
spam those people when in doubt.  We already have the signed-off's and
Maintainers file.  So this should be ok.  And if need be, the maintainers
can always forward the patch.

[i probably could make a diploma thesis out of this changelog :)]

Signed-off-by: Florian Mickler <florian@mickler.org>
Acked-by: Wolfram Sang <w.sang@pengutronix.de>
Cc: Joe Perches <joe@perches.com>
Cc: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

scripts/get_maintainer.pl: add .get_maintainer.conf default options file

Allow the use of a .get_maintainer.conf file to control the default
options applied when scripts/get_maintainer.pl is run.

.get_maintainer.conf can contain any valid command-line argument.

File contents are prepended to any additional command line arguments.

Multiple lines may be used, blank lines ignored, # is a comment.

Updated scripts/get_maintainer.pl version to 0.24

Signed-off-by: Joe Perches <joe@perches.com>
Reviewed-by: Florian Mickler <florian@mickler.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>