aacraid: Remove code to needlessly complete fib

Currently driver completes double completed or spurious interrupted fibs.
This  is not necessary and causes the SCSI mid layer to issue aborts and
resets, since completing a fib  prematurely might trigger a race condition
resulting in the driver not calling the scsi_done callback.

Fixed by removing the call to fib complete.

Signed-off-by: Raghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

aacraid: Log firmware AIF messages

Firmware AIF messages about cache loss and data recovery are being missed
by the driver since currently they are not captured but rather let go.
This patch to capture those messages and log them for the user.

Signed-off-by: Raghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

aacraid: Fix for aac_command_thread hang

Typically under error conditions, it is possible for aac_command_thread()
to miss the wakeup from kthread_stop() and go back to sleep, causing it
to hang aac_shutdown.

In the observed scenario, the adapter is not functioning correctly and so
aac_fib_send() never completes (or time-outs depending on how it was
called). Shortly after aac_command_thread() starts it performs
aac_fib_send(SendHostTime) which hangs. When aac_probe_one
/aac_get_adapter_info send time outs, kthread_stop is called which breaks
the command thread out of it's hang.

The code will still go back to sleep in schedule_timeout() without
checking kthread_should_stop() so it causes aac_probe_one to hang until
the schedule_timeout() which is 30 minutes.

Fixed by: Adding another kthread_should_stop() before schedule_timeout()
Cc: stable@vger.kernel.org
Signed-off-by: Raghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

aacraid: Disable MSI mode for series 6, 7, 8 cards

As the firmware for series 6, 7, 8 cards does not support msi, remove it
in the driver

Signed-off-by: Raghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

aacraid: Relinquish CPU during timeout wait

aac_fib_send has a special function case for initial commands during
driver initialization using wait < 0(pseudo sync mode). In this case,
the command does not sleep but rather spins checking for timeout.This
loop is calls cpu_relax() in an attempt to allow other processes/threads
to use the CPU, but this function does not relinquish the CPU and so the
command will hog the processor. This was observed in a KDUMP
"crashkernel" and that prevented the "command thread" (which is
responsible for completing the command from being timed out) from
starting because it could not get the CPU.

Fixed by replacing "cpu_relax()" call with "schedule()"
Cc: stable@vger.kernel.org
Signed-off-by: Raghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

aacraid: Start adapter after updating number of MSIX vectors

The adapter has to be started after updating the number of MSIX Vectors

Fixes: ecc479e00db8 (aacraid: Set correct MSIX count for EEH recovery)
Cc: stable@vger.kernel.org
Signed-off-by: Raghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

aacraid: Fix incorrectly named MACRO

Suggested-by: Seymour, Shane M <shane.seymour@hpe.com>
Signed-off-by: Raghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

aacraid: Removed unnecessary checks for NULL

Current driver checks for NULL return from aac_fib_alloc_tag, but it not
possible for it to return NULL.

Fixed by: Remove all the checks for NULL returns from aac_fib_alloc_tag

Suggested-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Raghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

mptsas: fix checks for dma mapping errors

mptsas_smp_handler() checks for dma mapping errors by comparison
returned address with zero, while pci_dma_mapping_error() should be
used.

Found by Linux Driver Verification project (linuxtesting.org).

Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Acked-by: Sathya Prakash Veerichetty <sathya.prakash@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

MAINTAINERS: Update the file list for the NCR 5380 entry

The file atari_NCR5380.c has been removed from the tree so remove it
from the MAINTAINERS file as well.

While we are here, add the file dtc3x80.txt as it is only relevant to
the dtc driver.

Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

st: clear ILI if Medium Error

Some drives set the ILI flag together with MEDIUM ERROR sense code.
Clear the ILI flag in this case so that the medium error will be
handled.  The problem was reported by Maurizio Lombardi.

Signed-off-by: Kai Mäkisara <kai.makisara@kolumbus.fi>
Reviewed-by: Laurence Oberman <loberman@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

lpfc: remove incorrect lockdep assertion

Remove incorrect lockdep assertion from lpfc_sli_hbqbuf_find() which
acquires the hbalock itself. Fix the comment which resulted in this
mistake.

Fixes: 1c2ba475eb0e ("lpfc: Add lockdep assertions")
Signed-off-by: Sebastian Herbszt <herbszt@gmx.de>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

bnx2i: silence uninitialized variable warnings

Presumably it isn't possible to have empty lists here, but my static
checker doesn't know that and complains that "ep" can be used
uninitialized.

Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Nilesh Javali <nilesh.javali@qlogic.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

hpsa: set the enclosure identifier to zero

This has only called from show_sas_rphy_enclosure_identifier().  The
caller expects that we set an identifier, otherwise it uses an
uninitialized variable.

[mkp: fixed typo]

Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

mpt3sas - remove unused fw_event_work elements

Firmware events are queued up using the fw_event_work's struct work, not
its delayed_work member.  The initial driver for SAS2 controllers had
handled firmware reset using the rescan barrier and was later redesigned
through "mpt2sas: [Resend] Host Reset code cleanup".  The delayed_work
variables are now unused and may provoke CONFIG_DEBUG_OBJECTS_TIMERS
"assert_init not available" false warnings in
_scsih_fw_event_cleanup_queue.

Cleanup fw_event_work's unused entries, update its kerneldoc, and
update _scsih_fw_event_cleanup_queue accordingly.

Fixes: 146b16c8071f (mpt3sas: Refcount fw_events and fix unsafe list usage)
Signed-off-by: Joe Lawrence <joe.lawrence@stratus.com>
Acked-by: Chaitra P B <chaitra.basappa@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

hisi_sas: add alloc_dev_quirk_v2_hw()

Add custom version of function to allocate device,
alloc_dev_quirk_v2_hw().  For sata devices the device id bit0 should be
0.

Signed-off-by: John Garry <john.garry@huawei.com>
Reviewed-by: Hannes Reinicke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

hisi_sas: add slot_index_alloc_quirk_v2_hw()

Add v2 hw custom function slot_index_alloc_quirk_v2_hw().  SAS devices
should have IPTT bit0 equal to 1.

Signed-off-by: John Garry <john.garry@huawei.com>
Reviewed-by: Hannes Reinicke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

hisi_sas: add device and slot alloc hw methods

Add methods to use HW specific versions of functions to allocate slot
and device.  HW specific methods are permitted to workaround device id
vs IPTT collision issue in v2 hw.

Signed-off-by: John Garry <john.garry@huawei.com>
Reviewed-by: Hannes Reinicke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

megaraid_sas: driver version upgrade

Signed-off-by: Sumit Saxena <sumit.saxena@broadcom.com>
Reviewed-by: Hannes Reinicke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

megaraid_sas: task management code optimizations

This patch will do code optmization for task management functions.
Below are key changes:

1. Remove reset_device hook as it was not being used and driver was
setting this to NULL.

2. Create wrapper functions for task abort and target reset and inside
   these functions adapter specific calls be made. e.g. fusion adapters
   support task abort and target reset so task abort and target reset
   should be issued to fusion adapters only and for MFI adapters, print
   a message saying feature not supported.

Signed-off-by: Sumit Saxena <sumit.saxena@broadcom.com>
Reviewed-by: Hannes Reinicke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

megaraid_sas: call ISR function to clean up pending replies in OCR path

In OCR path, before calling chip reset calls function
megasas_wait_for_outstanding_fusion to check reason for OCR. In case of
firmware FAULT initiated OCR and DCMD timeout initiated timeout, driver
will clear any outstanding reply (yet to be processed by driver) in
reply queues before going for chip reset. This code is added to handle a
scenario when IO timeout initiated adapter reset and management
application initiated adapter reset (by sending command to FAULT
firmware) happens simultaneously since adapter reset function is
safe-guarded by reset_mutex so only thread will be doing controller
reset. Consider IO timeout thread gets mutex and proceeds with adapter
reset process after disabling interrupts and by the time management
application has fired command to firmware to do adapter reset and the
same command is completed by firmware but since interrupts are disabled,
driver will not get completion and the same command will be in
outstanding/pending commands list of driver and refires same command
from IO timeout thread after chip reset which will again FAULT firmware
and eventually causes kill adapter.

Signed-off-by: Sumit Saxena <sumit.saxena@broadcom.com>
Reviewed-by: Hannes Reinicke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

megaraid_sas: reduce memory footprints in kdump mode

This patch will reduce memory footprints of megaraid_sas driver when
booted in kdump mode.  Driver will not allocate memory for optional and
perfromance oriented features.  Below are key changes done in
megaraid_sas driver to do this:

1. Limit Controller's queue depth to 100 in kdump mode.

2. Do not allocate memory for system info buffer and PD info buffer.

3. Disable performance oriented features e.g. Disable RDPQ mode, disable
   dual queue depth, restrict to single MSI-x vector.

Signed-off-by: Sumit Saxena <sumit.saxena@broadcom.com>
Reviewed-by: Hannes Reinicke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi_dh_alua: Declare local functions static

This patch avoids that building with W=1 causes gcc to report the
following type of warning:

    no previous prototype for ... [-Wmissing-prototypes]

Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Reviewed-by: Hannes Reinicke <hare@suse.de>
Cc: Hannes Reinecke <hare@suse.de>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Ewan Milne <emilne@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

mpt3sas: Remove usage of 'struct timeval'

'struct timeval' will have its tv_sec value overflow on 32-bit systems
in year 2038 and beyond. This patch replaces the use of struct timeval
for computing mpi_request.TimeStamp, and instead uses ktime_t which
provides 64-bit seconds value. The timestamp computed remains
unaffected (milliseconds since Unix epoch).

Signed-off-by: Tina Ruchandani <ruchandani.tina@gmail.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Acked-by: Sathya Prakash <sathya.prakash@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

pm80xx: Remove bogus address masking in pm8001_ioremap()

It is unclear what the original intent of the masking was, but it is
clearly incorrect to truncate a physical address before calling
ioremap().  On systems where there are valid physical address bits above
bit-31 (arm64 for example) the result is an eventual OOPs when
initializing the driver.

Remove the bogus code to fix it.

Signed-off-by: David Daney <david.daney@cavium.com>
Acked-by: Jack Wang <jinpu.wang@profitbricks.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

qla2xxx: Remove use of 'struct timeval'

struct register_host_info stores a 64-bit UTC system time timestamp.
This patch removes the use of 'struct timeval' to obtain that timestamp
as its tv_sec value will overflow on 32-bit systems in year 2038 beyond.
The patch uses ktime_get_real_seconds() which returns a 64-bit seconds value.

Signed-off-by: Tina Ruchandani <ruchandani.tina@gmail.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Acked-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

hisi_sas: update driver version to 1.4

Signed-off-by: John Garry <john.garry@huawei.com>
Reviewed-by: Zhangfei Gao <zhangfei.gao@linaro.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

hisi_sas: for v2 hw only set ITCT qw2 for SAS device

This patch fixes the ITCT table setup as it should be configured
differently for SAS and SATA devices.  For SATA disks there is no need
to set qw2 (already zeroed).  Also, link parameters for Bus inactive
limit, max connection time limit, and reject to open limit timers
parameters are changed to match global config register,
MAX_CON_TIME_LIMIT_TIME, as recommended by hw team.

Signed-off-by: John Garry <john.garry@huawei.com>
Reviewed-by: Zhangfei Gao <zhangfei.gao@linaro.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

hisi_sas: add v2 hw support for >4 SATA phys

This patch adds support for directly attaching SATA disks to phy
4-8. The problem was that only registers concerned with phy 0-3 were
being considered in sata_int_v2_hw().  The issue was not detected
previously as the development board only exposed phy 0-3; the new board
provides access to 8 phys.

Signed-off-by: John Garry <john.garry@huawei.com>
Reviewed-by: Zhangfei Gao <zhangfei.gao@linaro.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

hisi_sas: fix v2 hw multiple SATA disk issue

Intermittently it is found that when multiple SATA disks are directly
connected to the host that some disks are not detected.  The problem is
that all set bitfields in ENT_INT_SRC1 are cleared for all phys in
sata_int_v2_hw() - it should clear the set bit for the phy being
serviced.

Also unnecessary double-write to ENT_INT_SRC1 and ENT_INT_SRC_MSK1 is
removed (remaining writes are done at end label).

Signed-off-by: John Garry <john.garry@huawei.com>
Reviewed-by: Zhangfei Gao <zhangfei.gao@linaro.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

hisi_sas: use device linkrate in MCR for v2 hw

Contrary to the field name, the MCR (max connection rate) in the ITCT
should hold the device linkrate (linkrate of the connected phy), and not
the max linkrate.

This fixes an issue seen where some SATA drives connected through an
expander which would not attach.

Signed-off-by: John Garry <john.garry@huawei.com>
Reviewed-by: Zhangfei Gao <zhangfei.gao@linaro.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

lib: scatterlist: move SG pool code from SCSI driver to lib/sg_pool.c

Now it's ready to move the mempool based SG chained allocator code from
SCSI driver to lib/sg_pool.c, which will be compiled only based on a Kconfig
symbol CONFIG_SG_POOL.

SCSI selects CONFIG_SG_POOL.

Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Ming Lin <ming.l@ssi.samsung.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: rename SCSI_MAX_{SG, SG_CHAIN}_SEGMENTS

Rename SCSI_MAX_SG_SEGMENTS to SG_CHUNK_SIZE, which means the amount
we fit into a single scatterlist chunk.

Rename SCSI_MAX_SG_CHAIN_SEGMENTS to SG_MAX_SEGMENTS.

Will move these 2 generic definitions to scatterlist.h later.

Reviewed-by: Christoph Hellwig <hch@lst.de>
Acked-by: Bart Van Assche <bart.vanassche@sandisk.com> (for ib_srp changes)
Signed-off-by: Ming Lin <ming.l@ssi.samsung.com>
Acked-by: Tejun Heo <tj@kernel.org>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: rename SG related struct and functions

Rename SCSI specific struct and functions to more genenic names.

Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Ming Lin <ming.l@ssi.samsung.com>
Reviewed-by: Sagi Grimberg <sgi@grimberg.me>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: replace "mq" with "first_chunk" in SG functions

Parameter "bool mq" is block driver specific.
Change it to "first_chunk" to make it more generic.

Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Ming Lin <ming.l@ssi.samsung.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: replace "scsi_data_buffer" with "sg_table" in SG functions

Replace parameter "struct scsi_data_buffer" with "struct sg_table" in
SG alloc/free functions to make them generic.

Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Ming Lin <ming.l@ssi.samsung.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

zfcp: Revert to original scanning behaviour

zfcp has its own mechanism for selective scanning, so revert to the
original scanning behaviour to not confuse users.

Fixes: 4e91e876e9b8b6eb4255aa0d690778a89d3f1d28
Suggested-by: Benjamin Block <bblock@linux.vnet.ibm.com>
Signed-off-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Benjamin Block <bblock@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

mvsas: Generalize Marvell 9485 in pci_device_id

Claim Marvell 9485 controllers regardless of subdevice ID.

Tested on ASUS P9A-I/C2550/SAS/4L which uses vendor-specific 1043:8635.

[mkp: Tweaked commit message]

Signed-off-by: Leonid Moiseichuk <leonid.moiseichuk@gmail.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

bnx2fc: Update version number to 2.10.3.

Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

bnx2fc: Check sc_cmd device and host pointer before returning the command to the mid-layer.

When we are in connection recovery and the internal command timer on a
request pops, either the scsi_cmnd->device or scsi_cmnd->device->host
back pointers may be NULL as the device that the command that the
request was submitted on may have been subsequently reaped due to the
connection recovery. This can cause one or both of the pointers above to
be NULL and cause a system crash if we try to return the command to the
midlayer.

Instead, double check the pointers before the return to the midlayer so
as to prevent the crash and let the upper layers finish the session
recovery and rediscover the device.

Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

bnx2fc: Print netdev device name when FCoE is successfully initialized.

Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

bnx2fc: Print when we send a fip keep alive.

Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

bnx2fc: Add driver tunables.

Per customer request, add the following driver tunables:

o devloss_tmo
o max_luns
o queue_depth
o tm_timeout

tm_timeout is set per scsi_host in /sys/class/scsi_host/hostX/tm_timeout.

Signed-off-by: Joe Carnuccio <joe.carnuccio@qlogic.com>
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: vpd pages are mandatory for SPC-2

VPD pages 0x0 and 0x83 are mandatory even for SPC-2, so we should be
lowering the restriction to avoid having to whitelist every SPC-2
compliant device.

Signed-off-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

Revert "scsi: fix soft lockup in scsi_remove_target() on module removal"

Now that we've done a more comprehensive fix with the intermediate
target state we can remove the previous hack introduced with commit
90a88d6ef88e ("scsi: fix soft lockup in scsi_remove_target() on module
removal").

Signed-off-by: Johannes Thumshirn <jthumshirn@suse.de>
Cc: stable@vger.kernel.org
Reviewed-by: Ewan D. Milne <emilne@redhat.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: Add intermediate STARGET_REMOVE state to scsi_target_state

Add intermediate STARGET_REMOVE state to scsi_target_state to avoid
running into the BUG_ON() in scsi_target_reap(). The STARGET_REMOVE
state is only valid in the path from scsi_remove_target() to
scsi_target_destroy() indicating this target is going to be removed.

This re-fixes the problem introduced in commits bc3f02a795d3 ("[SCSI]
scsi_remove_target: fix softlockup regression on hot remove") and
40998193560d ("scsi: restart list search after unlock in
scsi_remove_target") in a more comprehensive way.

[mkp: Included James' fix for scsi_target_destroy()]

Signed-off-by: Johannes Thumshirn <jthumshirn@suse.de>
Fixes: 40998193560dab6c3ce8d25f4fa58a23e252ef38
Cc: stable@vger.kernel.org
Reported-by: Sergey Senozhatsky <sergey.senozhatsky@gmail.com>
Tested-by: Sergey Senozhatsky <sergey.senozhatsky@gmail.com>
Reviewed-by: Ewan D. Milne <emilne@redhat.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: James Bottomley <jejb@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

snic: add scsi host after determining max IOs.

scsi host is added after negotiating the max number of IOs with
Firmware.

Signed-off-by: Narsimhulu Musini <nmusini@cisco.com>
Signed-off-by: Sesidhar Baddela <sebaddel@cisco.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

snic: Fixing race in the hba reset and IO/TM completion

While HBA reset is in progress, if IO/TM completion is received for the
same IO then IO/TM completion path releases the driver private resources
associated with IO. This fix prevents releasing the resources in
IO and TM completion path if HBA reset is in progress.

Signed-off-by: Narsimhulu Musini <nmusini@cisco.com>
Signed-off-by: Sesidhar Baddela <sebaddel@cisco.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

snic: Fix for missing interrupts

- On posting an IO to the firmware, adapter generates an interrupt.
  Due to hardware issues, sometimes the adapter fails to generate
  the interrupt. This behavior skips updating transmit queue-
  counters, which in turn causes the queue full condition. The fix
  addresses the queue full condition.

- The fix also reserves a slot in transmit queue for hba reset.
  when queue full is observed during IO, there will always be room
  to post hba reset command.

Signed-off-by: Narsimhulu Musini <nmusini@cisco.com>
Signed-off-by: Sesidhar Baddela <sebaddel@cisco.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

snic: target cleanup in driver unload path

Fix deletes the snic targets synchronously prior to deletion of host.

Signed-off-by: Narsimhulu Musini <nmusini@cisco.com>
Signed-off-by: Sesidhar Baddela <sebaddel@cisco.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

snic: Handling control path queue issues

Fix handles control path queue issues such as queue full and sudden
removal of hardware.

Signed-off-by: Narsimhulu Musini <nmusini@cisco.com>
Signed-off-by: Sesidhar Baddela <sebaddel@cisco.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

snic: LUN goes offline due to scsi cmd timeouts

- LUN goes offline if there are at least two scsi command timeouts
  Completing the IO with scsi_done() fixes the issue.

Signed-off-by: Narsimhulu Musini <nmusini@cisco.com>
Signed-off-by: Sesidhar Baddela <sebaddel@cisco.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

snic: Added additional stats

Adding additional stats, and fixed logging messages.
- Added qdepth change stats
- Added separate isr stats for each type of interrupt
- Fixed race in updating active IOs
- Suppressed Link event message for DAS backend.

Signed-off-by: Narsimhulu Musini <nmusini@cisco.com>
Signed-off-by: Sesidhar Baddela <sebaddel@cisco.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

lpfc: Update driver version to 11.1.0.0

Signed-off-by: Dick Kennedy <dick.kennedy@avagotech.com>
Signed-off-by: James Smart <james.smart@avagotech.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

lpfc: Update modified file copyrights

Signed-off-by: Dick Kennedy <dick.kennedy@avagotech.com>
Signed-off-by: James Smart <james.smart@avagotech.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

lpfc: Fix interaction between fdmi_on and enable_SmartSAN

Signed-off-by: Dick Kennedy <dick.kennedy@avagotech.com>
Signed-off-by: James Smart <james.smart@avagotech.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

lpfc: Add support for SmartSAN 2.0

Revise versions to reflect SmartSAN 2.0 support

RDP updated to support additional descriptors:
  Credit descriptor
  Optical Element Data descriptors for Temperature, Voltage,
        Bias current, TX power and TX power.
  Optical Product Data descriptor.

Signed-off-by: Dick Kennedy <dick.kennedy@avagotech.com>
Signed-off-by: James Smart <james.smart@avagotech.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

lpfc: Fix Device discovery failures during switch reboot test.

When the switch is rebooted, the lpfc driver fails to log
into the fabric, and Unexpected timeout message is seen.

Fix: Do not issue RegVFI if the FLOGI was internally aborted.

Signed-off-by: Dick Kennedy <dick.kennedy@avagotech.com>
Signed-off-by: James Smart <james.smart@avagotech.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

lpfc: Utilize embedded CDB logic to minimize IO latency

Pass cmd iu payloads inline to adapter job structure rather than as
separate dma buffers.

Signed-off-by: Dick Kennedy <dick.kennedy@avagotech.com>
Signed-off-by: James Smart <james.smart@avagotech.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

lpfc: Fix crash when unregistering default rpi.

The default rpi completion handler does back to back puts to force the
removal of the ndlp. This ends up calling lpfc_unreg_rpi after the
reference count is at 0.

Fix:  Check the reference count of the ndlp before getting the ref to
make sure we are not getting a reference on a removed object.

Signed-off-by: Dick Kennedy <dick.kennedy@avagotech.com>
Signed-off-by: James Smart <james.smart@avagotech.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

lpfc: Fix DMA faults observed upon plugging loopback connector

Driver didn't program the REG_VFI mailbox correctly, giving the adapter
bad addresses.

Signed-off-by: Dick Kennedy <dick.kennedy@avagotech.com>
Signed-off-by: James Smart <james.smart@avagotech.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

lpfc: Correct LOGO handling during login

After a link bounce, when a remote port issues a LOGO while a REGLOGIN
is pending on that port, the driver does not clean up the ndlp
structure. May result in stack traces in the console log.

Fix: Clear the NLP_REG_LOGIN_SEND flag on the ndlp in the routine

Signed-off-by: Dick Kennedy <dick.kennedy@avagotech.com>
Signed-off-by: James Smart <james.smart@avagotech.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi_transport_iscsi: Declare local symbols static

Avoid that building with W=1 causes gcc to report warnings about symbols
that have not been declared.

Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi_transport_iscsi: Unexport iscsi_is_flashnode_conn_dev()

The output of "git grep -nHw iscsi_is_flashnode_conn_dev" shows that
this function is only called from inside source file
drivers/scsi/scsi_transport_iscsi.c. Hence unexport this function.

Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi_transport_iscsi: Remove set-but-not-used variables

Avoid that building with W=1 causes gcc to report warnings about
set-but-not-used variables.

Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

libiscsi: Remove set-but-not-used variables

Avoid that building with W=1 causes gcc to report warnings about
set-but-not-used variables.

Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

libiscsi: Unexport iscsi_eh_target_reset()

Running "git grep -nHw iscsi_eh_target_reset" shows that this function
is only called from inside the drivers/scsi/libiscsi.c source
file. Hence unexport this function.

Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

qla2xxx: Indicate out-of-memory with -ENOMEM

In the Linux kernel it is preferred to return a meaningful error code
instead of -1. This patch does not change the behavior of the caller of
qla82xx_pinit_from_rom().

Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Cc: Quinn Tran <quinn.tran@qlogic.com>
Cc: Himanshu Madhani <himanshu.madhani@qlogic.com>
Cc: Christoph Hellwig <hch@lst.de>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Acked-by: Quinn Tran <quinn.tran@qlogic.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi_transport_fc: Unexport scsi_is_fc_vport()

Running the command "git grep -nHw scsi_is_fc_vport" shows that this
function is only called from inside scsi_transport_fc.c. Hence unexport
this function.

Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Cc: Hannes Reinecke <hare@suse.de>
Cc: James Smart <james.smart@avagotech.com>
Reviewed-by: Hannes Reinicke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

fnic: Using rport->dd_data to check rport online instead of rport_lookup.

When issuing I/O we check if rport is online through libfc
rport_lookup() function which needs to be protected by mutex lock that
cannot acquired in I/O context. The change is to use midlayer remote
port s dd_data which is preserved until its devloss timeout and no
protection is required.  The the scsi_cmnd error code is expected to be
in the left 16 bits of the result field. Changed to correct this.  Fnic
driver version changed from 1.6.0.20 to 1.6.0.21

Signed-off-by: Satish Kharat <satishkh@cisco.com>
Signed-off-by: Sesidhar Baddela <sebaddel@cisco.com>
Reviewed-by: Ewan Milne <emilne@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

fnic: Cleanup the I/O pending with fw and has timed out and is used to issue LUN reset

In case of LUN reset, the device reset command is issued with one of the
I/Os that has timed out on that LUN. The change is to also return this
I/O with error status set to DID_RESET. In case when the reset is issued
using the sg_reset tool (from sg3_utils) it is a new command and new_sc
is set to 1.  Fnic driver version changed from 1.6.0.19 to 1.6.0.20

[mkp: Fixed checkpatch warning]

Signed-off-by: Satish Kharat <satishkh@cisco.com>
Signed-off-by: Sesidhar Baddela <sebaddel@cisco.com>
Reviewed-by: Ewan Milne <emilne@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

fnic: Fix to cleanup aborted IO to avoid device being offlined by mid-layer

If an I/O times out and an abort issued by host, if the abort is
successful we need to set scsi status as DID_ABORT. Or else the
mid-layer error handler which looks for this error code, will offline
the device. Also if the original I/O is not found in fnic firmware, we
will consider the abort as successful.  The start_time assignment is
moved because of the new goto.  Fnic driver version changed from
1.6.0.17a to 1.6.0.19, version 1.6.0.18 has been skipped

[mkp: Fixed checkpatch warning]

Signed-off-by: Satish Kharat <satishkh@cisco.com>
Signed-off-by: Sesidhar Baddela <sebaddel@cisco.com>
Reviewed-by: Ewan D. Milne <emilne@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi-trace: define ZBC_IN and ZBC_OUT

Add new trace functions for ZBC_IN and ZBC_OUT.

Reviewed-by: Doug Gilbert <dgilbert@interlog.com>
Reviewed-by: Ewan D. Milne <emilne@redhat.com>
Signed-off-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi-trace: Decode MAINTENANCE_IN and MAINTENANCE_OUT commands

Reviewed-by: Ewan D. Milne <emilne@redhat.com>
Signed-off-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi-trace: remove service action definitions

scsi_opcode_name() is displaying the opcode, not the service
action.

Reviewed-by: Ewan D. Milne <emilne@redhat.com>
Signed-off-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: disable automatic target scan

On larger installations it is useful to disable automatic LUN scanning,
and only add the required LUNs via udev rules.  This can speed up bootup
dramatically.

This patch introduces a new scan module parameter value 'manual', which
works like 'none', but can be overridden by setting the 'rescan' value
from scsi_scan_target to 'SCSI_SCAN_MANUAL'.  And it updates all
relevant callers to set the 'rescan' value to 'SCSI_SCAN_MANUAL' if
invoked via the 'scan' option in sysfs.

Signed-off-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Ewan D. Milne <emilne@redhat.com>
Tested-by: Laurence Oberman <loberman@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

ncr5380: Call complete_cmd() for disconnected commands on bus reset

I'm told that some targets are liable to disconnect a REQUEST SENSE
command. Theoretically this would cause a command undergoing autosense to
be moved onto the disconnected list. The bus reset handler must call
complete_cmd() for these commands, otherwise the hostdata->sensing pointer
will not get cleared. That would cause autosense processing to stall and
a timeout or an incorrect scsi_eh_restore_cmnd() would eventually follow.

Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Reported-by: Michael Schmitz <schmitzmic@gmail.com>
Tested-by: Ondrej Zary <linux@rainbow-software.org>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

mac_scsi: Fix pseudo DMA implementation

Fix various issues: Comments about bus errors are incorrect. The
PDMA asm must return the size of the memory access that faulted so the
transfer count can be adjusted accordingly. A phase change may cause a
bus error but should not be treated as failure. A bus error does not
always imply a phase change and generally the transfer may continue.
Scatter/gather doesn't seem to work with PDMA due to overruns. This is
a pity because peak throughput seems to double with SG_ALL.
Tested on a Mac LC III and a PowerBook 520.

Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

atari_scsi: Allow can_queue to be increased for Falcon

The benefit of limiting can_queue to 1 is that atari_scsi shares the
ST DMA chip more fairly with other drivers (e.g. falcon-ide).

Unfortunately, this can limit SCSI bus utilization. On systems without
IDE, atari_scsi should issue SCSI commands whenever it can arbitrate for
the bus. Make that possible by making can_queue configurable.

Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Tested-by: Michael Schmitz <schmitzmic@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

atari_scsi: Set a reasonable default for cmd_per_lun

This setting does not need to be conditional on Atari ST or TT.

Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Tested-by: Michael Schmitz <schmitzmic@gmail.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

ncr5380: Update usage documentation

Update kernel parameter documentation for atari_scsi, mac_scsi and
g_NCR5380 drivers. Remove duplication.

Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

ncr5380: Remove DONT_USE_INTR and AUTOPROBE_IRQ macros

Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Tested-by: Michael Schmitz <schmitzmic@gmail.com>
Tested-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

ncr5380: Remove remaining register storage qualifiers

Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Tested-by: Michael Schmitz <schmitzmic@gmail.com>
Tested-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

ncr5380: Fix register decoding for debugging

Decode all bits in the chip registers. They are all useful at times.
Fix printk severity so that this output can be suppressed along with
the other debugging output.

Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Tested-by: Michael Schmitz <schmitzmic@gmail.com>
Tested-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

dmx3191d: Drop max_sectors limit

The dmx3191d driver is not capable of DMA or PDMA so all transfers
use PIO. Now that large slow PIO transfers periodically stop and call
cond_resched(), the max_sectors limit can go away.

Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

ncr5380: Reduce max_lun limit

The driver has a limit of eight LUs because of the byte-sized bitfield
that is used for busy flags. That means the maximum LUN is 7. The default
is 8.

Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Tested-by: Michael Schmitz <schmitzmic@gmail.com>
Tested-by: Ondrej Zary <linux@rainbow-software.org>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

ncr5380: Remove disused atari_NCR5380.c core driver

Now that atari_scsi and sun3_scsi have been converted to use the NCR5380.c
core driver, remove atari_NCR5380.c. Also remove the last vestiges of its
Tagged Command Queueing implementation from the wrapper drivers.

The TCQ support in atari_NCR5380.c is abandoned by this patch. It is not
merged into the remaining core driver because,

1) atari_scsi defines SUPPORT_TAGS but leaves FLAG_TAGGED_QUEUING disabled
by default, which indicates that it is mostly undesirable.

2) I'm told that it doesn't work correctly when enabled.

3) The algorithm does not make use of block layer tags which it will have
to do because scmd->tag is deprecated.

4) sun3_scsi doesn't define SUPPORT_TAGS at all, yet the the SUPPORT_TAGS
macro interacts with the CONFIG_SUN3 macro in 'interesting' ways.

5) Compile-time configuration with macros like SUPPORT_TAGS caused the
configuration space to explode, leading to untestable and unmaintainable
code that is too hard to reason about.

The merge_contiguous_buffers() code is also abandoned. This was unused
by sun3_scsi. Only atari_scsi used it and then only on TT, because only TT
supports scatter/gather. I suspect that the TT would work fine with
ENABLE_CLUSTERING instead. If someone can benchmark the difference then
perhaps the merge_contiguous_buffers() code can be be justified. Until
then we are better off without the extra complexity.

Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Tested-by: Michael Schmitz <schmitzmic@gmail.com>
Tested-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

sun3_scsi: Adopt NCR5380.c core driver

Add support for the custom Sun 3 DMA logic to the NCR5380.c core driver.
This code is copied from atari_NCR5380.c.

Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Tested-by: Michael Schmitz <schmitzmic@gmail.com>
Tested-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

atari_scsi: Adopt NCR5380.c core driver

Add support for the Atari ST DMA chip to the NCR5380.c core driver.
This code is copied from atari_NCR5380.c.

Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Tested-by: Michael Schmitz <schmitzmic@gmail.com>
Tested-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

ncr5380: Merge DMA implementation from atari_NCR5380 core driver

Adopt the DMA implementation from atari_NCR5380.c. This means that
atari_scsi and sun3_scsi can make use of the NCR5380.c core driver
and the atari_NCR5380.c driver fork can be made redundant.

Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Tested-by: Michael Schmitz <schmitzmic@gmail.com>
Tested-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

ncr5380: Adopt uniform DMA setup convention

Standardize the DMA setup hooks so that the DMA implementation in
atari_NCR5380.c can be reconciled with pseudo DMA implementation in
NCR5380.c.

Calls to NCR5380_dma_recv_setup() and NCR5380_dma_send_setup() return
a negative value on failure, zero on PDMA transfer success and a positive
byte count for DMA setup success.

This convention is not entirely new, but is now applied consistently.

Also remove a pointless Status Register access: the *phase assignment is
redundant because after NCR5380_transfer_dma() returns control to
NCR5380_information_transfer(), that routine then returns control
to NCR5380_main(), which means *phase is dead.

Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Tested-by: Michael Schmitz <schmitzmic@gmail.com>
Tested-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

ncr5380: Use DMA hooks for PDMA

Those wrapper drivers which use DMA define the REAL_DMA macro and
those which use pseudo DMA define PSEUDO_DMA. These macros need to be
removed for a number of reasons, not least of which is to have drivers
share more code.

Redefine the PDMA send and receive hooks as DMA setup hooks, so that the
DMA code can be shared by all 5380 wrapper drivers. This will help to
reunify the forked core driver.

Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Tested-by: Michael Schmitz <schmitzmic@gmail.com>
Tested-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

ncr5380: Remove BOARD_REQUIRES_NO_DELAY macro

The io_recovery_delay macro is intended to insert a microsecond delay
between the chip register accesses that begin a DMA operation. This
is reportedly needed for some ISA boards.

Reverse the sense of the macro test so that in the common case,
where no delay is required, drivers need not define the macro.

Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Tested-by: Michael Schmitz <schmitzmic@gmail.com>
Tested-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

ncr5380: Remove PSEUDO_DMA macro

For those wrapper drivers which only implement Programmed IO, have
NCR5380_dma_xfer_len() evaluate to zero. That allows PDMA to be easily
disabled at run-time and so the PSEUDO_DMA macro is no longer needed.

Also remove the spin counters used for debugging pseudo DMA drivers.

Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Tested-by: Michael Schmitz <schmitzmic@gmail.com>
Tested-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

ncr5380: Disable the DMA errata workaround flag by default

The only chip that needs the workarounds enabled is an early NMOS
device. That means that the common case is to disable them.

Unfortunately the sense of the flag is such that it has to be set
for the common case.

Rename the flag so that zero can be used to mean "no errata workarounds
needed". This simplifies the code.

Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Tested-by: Michael Schmitz <schmitzmic@gmail.com>
Tested-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

atari_NCR5380: Remove DMA_MIN_SIZE macro

Only the atari_scsi and sun3_scsi drivers define DMA_MIN_SIZE.
Both drivers also define NCR5380_dma_xfer_len, which means
DMA_MIN_SIZE can be removed from the core driver.

This removes another discrepancy between the two core drivers.

Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Tested-by: Michael Schmitz <schmitzmic@gmail.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

ncr5380: Remove REAL_DMA and REAL_DMA_POLL macros

For the NCR5380.c core driver, these macros are never used.
If REAL_DMA were to be defined, compilation would fail.

For the atari_NCR5380.c core driver, REAL_DMA is always defined.

Hence these macros are pointless.

Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Tested-by: Michael Schmitz <schmitzmic@gmail.com>
Tested-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

ncr5380: Remove FLAG_NO_PSEUDO_DMA where possible

Drivers that define PSEUDO_DMA also define NCR5380_dma_xfer_len.
The core driver must call NCR5380_dma_xfer_len which means
FLAG_NO_PSEUDO_DMA can be eradicated from the core driver.

dmx3191d doesn't define PSEUDO_DMA and has no use for FLAG_NO_PSEUDO_DMA,
so remove it there also.

Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Tested-by: Michael Schmitz <schmitzmic@gmail.com>
Tested-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

g_ncr5380: Remove CONFIG_SCSI_GENERIC_NCR53C400

This change brings a number of improvements: fewer macros, better test
coverage, simpler code and sane Kconfig options. The downside is a small
chance of incompatibility (which seems unavoidable).

CONFIG_SCSI_GENERIC_NCR53C400 exists to enable or inhibit pseudo DMA
transfers when the driver is used with 53C400-compatible cards. Thanks to
Ondrej Zary's patches, PDMA now works which means it can be enabled
unconditionally.

Due to bad design, CONFIG_SCSI_GENERIC_NCR53C400 ties together unrelated
functionality as it sets both PSEUDO_DMA and BIOSPARAM macros. This patch
effectively enables PSEUDO_DMA and disables BIOSPARAM.

The defconfigs and the Kconfig default leave CONFIG_SCSI_GENERIC_NCR53C400
undefined. Red Hat 9 and CentOS 2.1 were the same. This leaves both
PSEUDO_DMA and BIOSPARAM disabled. The effect of this patch should be
better performance from enabling PSEUDO_DMA.

On the other hand, Debian 4 and SLES 10 had CONFIG_SCSI_GENERIC_NCR53C400
enabled, so both PSEUDO_DMA and BIOSPARAM were enabled. This patch might
affect configurations like this by disabling BIOSPARAM. My best guess is
that this could be a problem only in the vanishingly rare case that
1) the CHS values stored in the boot device partition table are wrong and
2) a 5380 card is in use (because PDMA on 53C400 used to be broken).

Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Tested-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: reduce CONFIG_SCSI_CONSTANTS=y impact by 8k

On 64 bit, struct error_info has 6 bytes of padding, which amounts to
over 4k of wasted space in the additional[] array. We could easily get
rid of that by instead using separate arrays for the codes and the
pointers. However, we can do even better than that and save an
additional 6 bytes per entry: In the table, just store the sizeof()
the corresponding string literal. The cumulative sum of these is then
the appropriate offset into additional_text, which is built from the
concatenation (with '\0's inbetween) of the strings.

$ scripts/bloat-o-meter /tmp/vmlinux vmlinux
add/remove: 0/0 grow/shrink: 1/1 up/down: 24/-8488 (-8464)
function                                     old     new   delta
scsi_extd_sense_format                       136     160     +24
additional                                 11312    2824   -8488

The Kconfig help text used to say that CONFIG_SCSI_CONSTANTS=y costs
around 75 KB, but that was a little exaggerated. The actual number was
closer to 44K, and 36K with this patch.

Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Tested-by: Douglas Gilbert <dgilbert@interlog.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>