wireless: Save original maximum regulatory transmission power for the calucation of the local maximum transmit power

The local maximum transmit power is the maximum power a wireless device
allowed to transmit. If Power Constraint is presented, the local maximum
power equals to the maximum allowed power defined in regulatory domain
minus power constraint.

The maximum transmit power is maximum power a wireless device capable of
transmitting, and should be used in Power Capability element (7.3.2.16
IEEE802.11 2007).

The transmit power from a wireless device should not greater than the
local maximum transmit power.

The maximum transmit power was not calculated correctly in the current
Linux wireless/mac80211 when Power Constraint is presented.

Signed-off-by: Hong Wu <hong.wu@dspg.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

carl9170: claim to support IBSS RSN.

On carl9170, HW encryption is disabled on IBSS; the mac80211
software-based encryption is used instead. As mac80211 supports IBSS
RSN (per-STA GTK), claim its support in the carl9170 PHY.

Signed-off-by: Nicolas Cavallari <cavallar@lri.fr>
Acked-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mac80211: In IBSS the DA field of auth frames is different from BSSID

In case of authentication frame exchange between two IBSS STAs, the
DA field must contain the destinatioin address (instead of the BSSID).

Signed-off-by: Antonio Quartulli <ordex@autistici.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mac80211: refactor __ieee80211_get_channel_mode

Use a switch statement instead of a list of if
statements. Also include AP_VLAN in the list
and skip them since the AP interface will also
be looked at.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

drivers/net/wireless/mwifiex/scan.c: convert GFP_KERNEL to GFP_ATOMIC

The function is called with locks held and thus should not use GFP_KERNEL.

The semantic patch that makes this report is available
in scripts/coccinelle/locks/call_kern.cocci.

More information about semantic patching is available at
http://coccinelle.lip6.fr/

Signed-off-by: Julia Lawall <julia.lawall@lip6.fr>
Acked-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

NFC: Increase NCI deactivate timeout

Increase NCI deactivate timeout from 5 sec to 30 sec.
NCI deactivate procedure might take a long time,
depending on the local and remote parameters.

Signed-off-by: Ilan Elias <ilane@ti.com>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

NFC: Complete NCI deactivate in deactivate_ntf

If a target was active, complete the NCI deactivate request
only in deactivate_ntf. Otherwise, complete it at deactivate_rsp.
Deactivate_ntf represents the actual disconnection event (sent from
the NCI controller).

Signed-off-by: Ilan Elias <ilane@ti.com>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rtl8192se: Update copyright dates

Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rtl8192de: Update copyright dates

Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rtl8192cu: Update copyright dates

Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rtl8192ce: Update copyright dates

Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rtl8192c_common: Update copyright dates

Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rtlwifi: Update copyright dates

Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rtl8192cu: Remove dead code never selected

The original driver contained some conditional code that was not selected,
but was not deleted in case it would be used later. That code can now be
removed.

Reported-by: Joe Perches <joe@perches.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rtlwifi: rtl8192c_common: rtl8192de: Check for allocation failures

In https://bugzilla.redhat.com/show_bug.cgi?id=771656, a kernel bug was
triggered due to a failed skb allocation that was not checked. This event
lead to an audit of all memory allocations in the complete rtlwifi family
of drivers. This patch fixes the rest.

Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@vger.kernel.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mac80211: minor cleanup

we would have bailed out if 'ifibss->fixed_channel'
is valid i.e. we had used 'fixed-freq' parameter in iw ibss
join command. this is with the state 'IEEE80211_IBSS_MLME_JOINED'
so no need to check for it

Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwlwifi: update Copyright

Update Copyright to 2012

Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwlwifi: add testmode cmd IWL_TM_CMD_APP2DEV_GET_FW_INFO

Add new testmode command IWL_TM_CMD_APP2DEV_GET_FW_INFO for
reporting the following information of existing loaded uCode image.
+ uCode type
+ Instruction section size
+ Data section size

Signed-off-by: Kenny Hsu <kenny.hsu@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwlwifi: update error dump in testmode command sram_read

The error message will be show up by using IWL_ERR
insteads of IWl_DEBUG_INFO.

Signed-off-by: Kenny Hsu <kenny.hsu@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwlwifi: enhance testmode command sram_read

This patch enables SRAM read function to support entire target memory.

Signed-off-by: Kenny Hsu <kenny.hsu@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwlwifi: update testmode command of direct register access

In order to make sure the testcommand function of direct register
access can be performed even NIC is asleep, replace corresponding
handler iwl_read32 and iwl_write32 by using iwl_direct_read32 and
iwl_direct_write32.

Signed-off-by: Kenny Hsu <kenny.hsu@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwlwifi: Sanity check for sta_id

On my testing, I saw some strange behavior

[  421.739708] iwlwifi 0000:01:00.0: ACTIVATE a non DRIVER active station id 148 addr 00:00:00:00:00:00
[  421.739719] iwlwifi 0000:01:00.0: iwl_sta_ucode_activate Added STA id 148 addr 00:00:00:00:00:00 to uCode

not sure how it happen, but adding the sanity check to prevent memory
corruption

Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwlwifi: don't process the info from uCode if does not has ownership

When enable the testmode from user space and working with uCode, driver does
not own the uCode and should not process the notifications or pkts from uCode

Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rtlwifi: Simplify chip version id logging

Reduce object size a few KB too.

$ size drivers/net/wireless/rtlwifi/built-in.o*
   text    data     bss     dec     hex filename
 584493   55333  126800  766626   bb2a2 drivers/net/wireless/rtlwifi/built-in.o.new
 586904   55333  127216  769453   bbdad drivers/net/wireless/rtlwifi/built-in.o.old

Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rtlwifi: Remove incorrect logging message prefixes

pr_fmt() adds them.  These are unnecessary and wrong.

Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rtlwifi: add CONFIG_RTLWIFI_DEBUG to remove all of the debug logging code

It does seem odd though to have a DBG_EMERG and not always
emit it.

What might also be useful for any embedded use is to add
CONFIG_RTLWIFI_DEBUG to conditionally remove all of the
debug logging code to reduce the largish object size.

This reduces the object size by about 1/3 (250KB)
when CONFIG_RTLWIFI_DEBUG is not set.

$ size drivers/net/wireless/rtlwifi/built-in.o*
   text    data     bss     dec     hex filename
 368722   55333   94224  518279   7e887 drivers/net/wireless/rtlwifi/built-in.o.new
 586904   55333  127216  769453   bbdad drivers/net/wireless/rtlwifi/built-in.o.old

Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rtlwifi: Optimize RT_TRACE macro use of KBUILD_MODNAME for size

Moving the KBUILD_MODNAME to the format reduces the
overall object size a small amount.

$ size drivers/net/wireless/rtlwifi/built-in.o*
   text    data     bss     dec     hex filename
 586904   55333  127216  769453   bbdad drivers/net/wireless/rtlwifi/built-in.o.new
 588901   55333  127216  771450   bc57a drivers/net/wireless/rtlwifi/built-in.o.old

Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rtlwifi: Remove duplicate __func__

The RT_TRACE macro already prepends it.

Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rtlwifi: Convert RT_ASSERT macro to use ##__VA_ARGS__

Consolidate printks to avoid possible message interleaving
and reduce the object size.

Remove unnecessary RT_ASSERT parentheses.
Align arguments.
Coalesce formats.
Remove unnecessary __func__ use as the macro uses it.

$ size drivers/net/wireless/rtlwifi/built-in.o*
   text    data     bss     dec     hex filename
 588901   55333  127216  771450   bc57a drivers/net/wireless/rtlwifi/built-in.o.new
 590002   55333  127560  772895   bcb1f drivers/net/wireless/rtlwifi/built-in.o.old

Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rtlwifi: Convert RTPRINT macro to use ##__VA_ARGS__

Consolidate printks to avoid possible message interleaving
and reduce the object size.

Remove unnecessary RTPRINT parentheses.
Coalesce formats.
Align arguments.

$ size drivers/net/wireless/rtlwifi/built-in.o*
   text    data     bss     dec     hex filename
 590002   55333  127560  772895   bcb1f drivers/net/wireless/rtlwifi/built-in.o.new
 594841   55333  129680  779854   be64e drivers/net/wireless/rtlwifi/built-in.o.old

Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rtlwifi: Convert RT_TRACE macro to use ##__VA_ARGS__

Consolidate printks to avoid possible message interleaving
and reduce the object size.

Remove unnecessary RT_TRACE parentheses.

Miscellaneous typo and grammar fixes.
Add missing newlines to formats.
Remove duplicate KERN_DEBUG prefixes.
Coalesce formats.
Align arguments.

$ size drivers/net/wireless/rtlwifi/built-in.o*
   text    data     bss     dec     hex filename
 594841   55333  129680  779854   be64e drivers/net/wireless/rtlwifi/built-in.o.new
 607022   55333  138720  801075   c3933 drivers/net/wireless/rtlwifi/built-in.o.old

Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rtlwifi: Standardize RT_PRINT_DATA macro and uses

Use a single printk(KERN_DEBUG to emit the header line
to avoid any possible output interleaving.

Remove unnecessary parentheses from the calling uses.
Standardize header arg without trailing \n or colon.
Fix a few pairwiase/pairwise typos.

Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rtlwifi: Neaten RT_ASSERT, RT_TRACE, RTPRINT, RT_PRINT_DATA macros

Make the macros a bit more readable.

Use do {...} while (0) without terminating semicolons.
Add missing terminating semicolon to a few uses.

Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

b43: N-PHY: trivial: change save&rest order in RSSI polling

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

b43: N-PHY: implement RSSI calibration for rev3+

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcm80211: make ethtool_ops const

All usage of ethtool_ops should be const; also add comma at end
of initializer list.

Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Acked-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

b43: N-PHY: upload PAPD PGA gain delta table

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

b43: N-PHY: fix typos in RF control

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

b43: N-PHY: add helper for getting gain table

Also move the code to tables file.

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

b43: N-PHY: implement TX power control setup

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

b43: add maskset helpers

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

bcma: SPROM: extract power info for cores

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

bcma: SPROM: add macro for easier extraction

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ssb: SPROM: extract each core power info

We already extract some basic info but it's incomplete, reads info
about the first core only. Used data structure doesn't allow easy
adding of more cores.
This patch adds new struct and array for storing power info. The plan
is to: switch all extractors (including the ones using NVRAM) to new
struct, switch drivers, then deprecate and finally drop old SSB fields.

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mac80211: check sta_apply_parameters() return value

Bail out if sta_apply_parameters() returns an error.

Signed-off-by: Eliad Peller <eliad@wizery.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

tg3: Fix single-vector MSI-X code

Kdump kernels leave MSI-X interrupts (as setup by the crashed kernel)
enabled.  However, kdump only enables one CPU in the new environment,
thus causing tg3 to abort MSI-X setup.  When the driver attempts to
enable INTA or MSI interrupt modes on a kdump kernel, interrupt
delivery fails.

This patch attempts to workaround the problem by forcing the driver
to enable a single MSI-X interrupt.  In such a configuration, the
device's multivector interrupt mode must be disabled.

Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

openvswitch: Fix multipart datapath dumps.

The logic to split up the list of datapaths into multiple Netlink messages
was simply wrong, causing the list to be terminated after the first part.
Only about the first 50 datapaths would be dumped.  This fixes the
problem.

Reported-by: Paul Ingram <paul@nicira.com>
Signed-off-by: Ben Pfaff <blp@nicira.com>
Signed-off-by: Jesse Gross <jesse@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

ipv6: fix per device IP snmp counters

In commit 4ce3c183fca (snmp: 64bit ipstats_mib for all arches), I forgot
to change the /proc/net/dev_snmp6/xxx output for IP counters.

percpu array is 64bit per counter but the folding still used the 'long'
variant, and output garbage on 32bit arches.

Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

inetpeer: initialize ->redirect_genid in inet_getpeer()

kmemcheck complains that ->redirect_genid doesn't get initialized.
Presumably it should be set to zero.

Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: fix NULL-deref in WARN() in skb_gso_segment()

Bug was introduced in commit c8f44affb7244f2ac3e703cab13d55ede27621bb.

Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: WARN if skb_checksum_help() is called on skb requiring segmentation

skb_checksum_help() has never done anything useful with skbs that
require segmentation.  Setting skb->ip_summed = CHECKSUM_NONE makes
them invalid and provokes a later WARNing in skb_gso_segment().

Passing such an skb to skb_checksum_help() indicates a bug, so we
should warn about it immediately.  Move the warning from
skb_gso_segment() into a shared function, and add gso_type and
gso_size to it.

Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge branch 'master' of git://git./linux/kernel/git/linville/wireless

caif: Remove bad WARN_ON in caif_dev

Remove WARN_ON and bad handling of SKB without destructor callback
in caif_flow_cb. SKB without destructor cannot be handled as an
error case.

Signed-off-by: Sjur Brændeland <sjur.brandeland@stericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

caif: Fix typo in Vendor/Product-ID for CAIF modems

Fix typo for the Vendor/Product Id for ST-Ericsson CAIF modems.
Discovery is based on fixed USB vendor 0x04cc (ST-Ericsson),
product-id 0x230f (NCM).

Signed-off-by: Sjur Brændeland <sjur.brandeland@stericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bnx2x: Disable AN KR work-around for BCM57810

Disable the work-around for the autoneg KR of the BCM57810 in case the Warpcore version is 0xD108 and above, which fixes this problem.

Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bnx2x: Remove AutoGrEEEn for BCM84833

Disable the autoGrEEEn feature for BCM84833.

Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bnx2x: Remove 100Mb force speed for BCM84833

Remove unsupported speed of 100Mb force for BCM84833 due to hardware
limitation.

Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bnx2x: Fix PFC setting on BCM57840

This patch handles the second port of a path in a 4-port device of
BCM57840.

Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bnx2x: Fix Super-Isolate mode for BCM84833

The Super-Isolate mode comes to isolate the BCM84833 PHY from the
outside world.  Not doing it correctly, made link partner see the link
before the driver was loaded.

This patch also involves SPIROM version fixes since it is used to
determine whether the common init of the PHY was already executed, and
the common init of this PHY is partially responsible for setting the
Super-Isolate mode.

Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: fix some sparse errors

make C=2 CF="-D__CHECK_ENDIAN__" M=net

And fix flowi4_init_output() prototype for sport

Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: kill duplicate included header

For net part, remove duplicate included header.

Signed-off-by: Shan Wei <davidshan@tencent.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: sh-eth: Fix build error by the value which is not defined

-----
drivers/net/ethernet/renesas/sh_eth.c:1706: error: 'pdid' undeclared (first use in this function)
drivers/net/ethernet/renesas/sh_eth.c:1706: error: (Each undeclared identifier is reported only once
drivers/net/ethernet/renesas/sh_eth.c:1706: error: for each function it appears in.)
make[5]: *** [drivers/net/ethernet/renesas/sh_eth.o] Error 1
-----

Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
CC: Florian Fainelli <florian@openwrt.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: Use device model to get driver name in skb_gso_segment()

ethtool operations generally require the caller to hold RTNL and are
not safe to call in atomic context.  The device model provides this
information for most devices; we'll only lose it for some old ISA
drivers.

Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>

bridge: BH already disabled in br_fdb_cleanup()

br_fdb_cleanup() is run from timer interrupt, BH already masked.

Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
CC: Stephen Hemminger <shemminger@vyatta.com>
CC: Štefan Gula <steweg@gmail.com>
Acked-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: move sock_update_memcg outside of CONFIG_INET

Although only used currently for tcp sockets, this function
is now used in common sock code (for sock_clone())

Commit 475f1b52645a29936b9df1d8fcd45f7e56bd4a9f moved the
declaration of sock_update_clone() to inside sock.c, but
this only fixes the problem when CONFIG_CGROUP_MEM_RES_CTLR_KMEM
is also not defined.

This patch here is verified to fix both problems, although
reverting the previous one is not necessary.

Signed-off-by: Glauber Costa <glommer@parallels.com>
CC: David S. Miller <davem@davemloft.net>
CC: Stephen Rothwell <sfr@canb.auug.org.au>
Reported-by: Randy Dunlap <rdunlap@xenotime.net>
Acked-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

mwl8k: Fixing Sparse ENDIAN CHECK warning

Fixing following sparse warning
>drivers/net/wireless/mwl8k.c:2780:15: warning: incorrect type in assignment (different base types)
>drivers/net/wireless/mwl8k.c:2780:15:    expected restricted unsigned short [usertype] channel
>drivers/net/wireless/mwl8k.c:2780:15:    got unsigned short [unsigned] [usertype] hw_value

Signed-off-by: Yogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mac80211: Fix possible race between sta_unblock and network softirq

All other code paths in sta_unblock synchronize with the network
softirq by using local_bh_disable/enable. Do the same around
ieee80211_sta_ps_deliver_wakeup.

Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mwl8k: fix condition in mwl8k_cmd_encryption_remove_key()

The intent here was to check whether key->cipher was WEP40 or WEP104.
We do a similar check correctly in several other places in this file.
The current condition is always true.

Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcmfmac: work-around gcc 4.7 build issue

Alexandre Oliva <oliva@lsd.ic.unicamp.br> says:

"It's an issue brought about by GCC 4.7's partial-inlining, that ends up
splitting the udelay function just at the wrong spot, in such a way that
some sanity checks for constants fails, and we end up calling
bad_udelay.

This patch fixes the problem.  Feel free to push it upstream if it makes
sense to you."

Signed-off-by: John W. Linville <linville@tuxdriver.com>

net: remove version.h includes in net/openvswitch/

remove version.h includes in net/openswitch/ as reported by make versioncheck.

Signed-off-by: Devendra Naga <devendra.aaru@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bql: Fix inconsistency between file mode and attr method.

There is no store() method for inflight attribute in the
tx-<n>/byte_queue_limits sysfs directory.
So remove S_IWUSR bit.

Signed-off-by: Hiroaki SHIMODA <shimoda.hiroaki@gmail.com>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

ehea: make some functions and variables static

Some functions and variables in ehea are only used in their own file, so
they should be static. One particular function had a very generic name,
print_error_data.

Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

brcmsmac: remove PCI suspend/resume from bcma driver

The brcmsmac driver isn't a PCI driver any more, it's a bcma one.  The
PCI device has been resumed by the PCI driver (the generic PCI layer,
really), we should be resuming just our own driver state.

Also add pr_debug() calls to show that we now actually get the
suspend/resume events.

Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

bcma: connect the bcma bus suspend/resume to the bcma driver suspend/resume

Now the low-level driver actually gets informed that it is getting suspended and resumed.

Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

bcma: add stub for bcma_bus_suspend()

.. and connect it up with the pci host bcma driver.

Now, the next step is to connect those bcma bus-level suspend/resume
functions to the actual bcma device suspend resume functions.

Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

bcma: convert suspend/resume to pm_ops

.. and avoid doing the unnecessary PCI operations - the PCI layer will
do them for us.

Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

netfilter: ipset: dumping error triggered removing references twice

If there was a dumping error in the middle, the set-specific variable was
not zeroed out and thus the 'done' function of the dumping wrongly tried
to release the already released reference of the set. The already released
reference was caught by __ip_set_put and triggered a kernel BUG message.
Reported by Jean-Philippe Menil.

Signed-off-by: Jozsef Kadlecsik <kadlec@blackhole.kfki.hu>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>

netfilter: ipset: autoload set type modules safely

Jan Engelhardt noticed when userspace requests a set type unknown
to the kernel, it can lead to a loop due to the unsafe type module
loading. The issue is fixed in this patch.

Signed-off-by: Jozsef Kadlecsik <kadlec@blackhole.kfki.hu>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>

mac80211: fix tx->skb NULL pointer dereference

In function ieee80211_tx_h_encrypt the var info was
initialized from tx->skb, since the fucntion
is called after the function ieee80211_tx_h_fragment
tx->skb is not valid anymore.

Signed-off-by: Yoni Divinsky <yoni.divinsky@ti.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

wireless: iwlwifi: iwl-scan.c: Fix build warning

Fix the following build warning:

drivers/net/wireless/iwlwifi/iwl-scan.c: In function ‘iwlagn_request_scan’:
drivers/net/wireless/iwlwifi/iwl-scan.c:572: warning: ‘cmd_len’ may be used uninitialized in this function

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Net, mac80211: Fix resource leak in ieee80211_rx_h_mesh_fwding()

We may leak the 'fwd_skb' we skb_copy() in ieee80211_rx_h_mesh_fwding() if
we take the 'else' branch in the 'if' statement just below. If we take
that branch we'll end up returning from the function and since we've not
assigned 'fwd_skb' to anything at that point, we leak it when the variable
goes out of scope.

The simple fix seems to be to just kfree_skb(fwd_skb); just before we
return. That is what this patch does.

Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k_hw: fix interpretation of the rx KeyMiss flag

Documentation states that the KeyMiss flag is only valid if RxFrameOK is
unset, however empirical evidence has shown that this is false.
When KeyMiss is set (and RxFrameOK is 1), the hardware passes a valid frame
which has not been decrypted. The driver then falsely marks the frame
as decrypted, and when using CCMP this corrupts the rx CCMP PN, leading
to connection hangs.

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>

bcma: invalidate the mapped core over suspend/resume

This clears the currently mapped core when suspending, to force
re-mapping after resume. Without that we were touching default core
registers believing some other core is mapped. Such a behaviour
resulted in lockups on some machines.

Cc: stable@vger.kernel.org
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

MAINTAINERS: add b43 mailing list

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

MAINTAINERS: move BCMA to keep the list sorted

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

netfilter: revert user-space expectation helper support

This patch partially reverts:
3d058d7 netfilter: rework user-space expectation helper support
that was applied during the 3.2 development cycle.

After this patch, the tree remains just like before patch bc01bef,
that initially added the preliminary infrastructure.

I decided to partially revert this patch because the approach
that I proposed to resolve this problem is broken in NAT setups.
Moreover, a new infrastructure will be submitted for the 3.3.x
development cycle that resolve the existing issues while
providing a neat solution.

Since nobody has been seriously using this infrastructure in
user-space, the removal of this feature should affect any know
FOSS project (to my knowledge).

Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>

netfilter: xt_hashlimit: fix unused variable warning if IPv6 disabled

Fixes this warning when CONFIG_IP6_NF_IPTABLES is not enabled:

net/netfilter/xt_hashlimit.c: In function ‘hashlimit_init_dst’:
net/netfilter/xt_hashlimit.c:448:9: warning: unused variable ‘frag_off’ [-Wunused-variable]

Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>

mac80211: fix no-op authorized transitions

When userspace attempts to authorize a station
that is already authorized, nothing happens as
you'd expect. Similarly, when it unauthorizes
a station that is associated, nothing happens.

However, when it unauthorizes a station that
isn't even associated yet, we erroneously try
to move the station to associated. This seems
to happen occasionally as a result of a race
when wpa_supplicant attempts to unauthorize
the port in managed mode. Particularly with my
new patches to keep stations, it can then move
a station into ASSOCIATED state before we have
really associated, which is really confusing.

I introduced this bug in
"mac80211: refactor station state transitions"

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rt2800pci: fix spurious interrupts generation

Same devices can generate interrupt without properly setting bit in
INT_SOURCE_CSR register (spurious interrupt), what will cause IRQ line
will be disabled by interrupts controller driver.

We discovered that clearing INT_MASK_CSR stops such behaviour. We
previously first read that register, and then clear all know interrupt
sources bits and do not touch reserved bits. After this patch, we write
to all register content (I believe writing to reserved bits on that
register will not cause any problems, I tested that on my rt2800pci
device).

This fix very bad performance problem, practically making device
unusable (since worked without interrupts), reported in:
https://bugzilla.redhat.com/show_bug.cgi?id=658451

We previously tried to workaround that issue in commit
4ba7d9997869d25bd223dea7536fc1ce9fab3b3b "rt2800pci: handle spurious
interrupts", but it was reverted in commit
82e5fc2a34fa9ffea38f00c4066b7e600a0ca5e6
as thing, that will prevent to detect real spurious interrupts.

Reported-and-tested-by: Amir Hedayaty <hedayaty@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ipw2x00: signedness bug handling frame length

This is basically just a cleanup.  Large positive numbers get counted as
negative but then get implicitly cast to positive again for the checks
that matter.

This does make a small difference in ipw_handle_promiscuous_rx() when we
test "if (unlikely((len + IPW_RX_FRAME_SIZE) > skb_tailroom(rxb->skb)))"
It should return there, but we don't return until a couple lines later
when we test "if (len > IPW_RX_BUF_SIZE - sizeof(struct ipw_rt_hdr)) {".
The difference is that in the second test the sizeof() means that there
is an implied cast to unsigned.

Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

wireless: b43: fix Oops on card eject during transfer

An Oops has once been observed, when the SDIO card had been ejected during
IO. The PC value shows, that the dev pointer in b43_op_stop() was NULL.

(I moved the NULL check before the lock, based upon a suggestion from
Julian Calaby <julian.calaby@gmail.com>. -- JWL)

Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

vhost-net: add module alias (v2.1)

By adding some module aliases, programs (or users) won't have to explicitly
call modprobe. Vhost-net will always be available if built into the kernel.
It does require assigning a permanent minor number for depmod to work.

Also:
  - use C99 style initialization.
  - add missing entry in documentation for loop-control

Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Acked-By: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

ipv6: release idev when ip6_neigh_lookup failed in icmp6_dst_alloc

release idev when ip6_neigh_lookup failed in icmp6_dst_alloc

Signed-off-by: RongQing.Li <roy.qing.li@gmail.com>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge branch 'akpm' (aka "Andrew's patch-bomb, take two")

Andrew explains:

 - various misc stuff

 - Most of the rest of MM: memcg, threaded hugepages, others.

 - cpumask

 - kexec

 - kdump

 - some direct-io performance tweaking

 - radix-tree optimisations

 - new selftests code

   A note on this: often people will develop a new userspace-visible
   feature and will develop userspace code to exercise/test that
   feature.  Then they merge the patch and the selftest code dies.
   Sometimes we paste it into the changelog.  Sometimes the code gets
   thrown into Documentation/(!).

   This saddens me.  So this patch creates a bare-bones framework which
   will henceforth allow me to ask people to include their test apps in
   the kernel tree so we can keep them alive.  Then when people enhance
   or fix the feature, I can ask them to update the test app too.

   The infrastruture is terribly trivial at present - let's see how it
   evolves.

 - checkpoint/restart feature work.

   A note on this: this is a project by various mad Russians to perform
   c/r mainly from userspace, with various oddball helper code added
   into the kernel where the need is demonstrated.

   So rather than some large central lump of code, what we have is
   little bits and pieces popping up in various places which either
   expose something new or which permit something which is normally
   kernel-private to be modified.

   The overall project is an ongoing thing.  I've judged that the size
   and scope of the thing means that we're more likely to be successful
   with it if we integrate the support into mainline piecemeal rather
   than allowing it all to develop out-of-tree.

   However I'm less confident than the developers that it will all
   eventually work! So what I'm asking them to do is to wrap each piece
   of new code inside CONFIG_CHECKPOINT_RESTORE.  So if it all
   eventually comes to tears and the project as a whole fails, it should
   be a simple matter to go through and delete all trace of it.

This lot pretty much wraps up the -rc1 merge for me.

* akpm: (96 commits)
  unlzo: fix input buffer free
  ramoops: update parameters only after successful init
  ramoops: fix use of rounddown_pow_of_two()
  c/r: prctl: add PR_SET_MM codes to set up mm_struct entries
  c/r: procfs: add start_data, end_data, start_brk members to /proc/$pid/stat v4
  c/r: introduce CHECKPOINT_RESTORE symbol
  selftests: new x86 breakpoints selftest
  selftests: new very basic kernel selftests directory
  radix_tree: take radix_tree_path off stack
  radix_tree: remove radix_tree_indirect_to_ptr()
  dio: optimize cache misses in the submission path
  vfs: cache request_queue in struct block_device
  fs/direct-io.c: calculate fs_count correctly in get_more_blocks()
  drivers/parport/parport_pc.c: fix warnings
  panic: don't print redundant backtraces on oops
  sysctl: add the kernel.ns_last_pid control
  kdump: add udev events for memory online/offline
  include/linux/crash_dump.h needs elf.h
  kdump: fix crash_kexec()/smp_send_stop() race in panic()
  kdump: crashk_res init check for /sys/kernel/kexec_crash_size
  ...

Merge git://git./linux/kernel/git/davem/net

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (69 commits)
  pptp: Accept packet with seq zero
  RDS: Remove some unused iWARP code
  net: fsl: fec: handle 10Mbps speed in RMII mode
  drivers/net/ethernet/stmicro/stmmac/stmmac_platform.c: add missing iounmap
  drivers/net/ethernet/tundra/tsi108_eth.c: add missing iounmap
  ksz884x: fix mtu for VLAN
  net_sched: sfq: add optional RED on top of SFQ
  dp83640: Fix NOHZ local_softirq_pending 08 warning
  gianfar: Fix invalid TX frames returned on error queue when time stamping
  gianfar: Fix missing sock reference when processing TX time stamps
  phylib: introduce mdiobus_alloc_size()
  net: decrement memcg jump label when limit, not usage, is changed
  net: reintroduce missing rcu_assign_pointer() calls
  inet_diag: Rename inet_diag_req_compat into inet_diag_req
  inet_diag: Rename inet_diag_req into inet_diag_req_v2
  bond_alb: don't disable softirq under bond_alb_xmit
  mac80211: fix rx->key NULL pointer dereference in promiscuous mode
  nl80211: fix old station flags compatibility
  mdio-octeon: use an unique MDIO bus name.
  mdio-gpio: use an unique MDIO bus name.
  ...

unlzo: fix input buffer free

unlzo modifies the pointer to in_buf, so we have to free the original
buffer, not the modified pointer.

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Lasse Collin <lasse.collin@tukaani.org>
Cc: Namhyung Kim <namhyung@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

ramoops: update parameters only after successful init

If a platform device exists on the system, but ramoops fails to attach to
it, the module parameters are overridden before ramoops can fall back and
try to use passed module parameters.  Move update to end of init routine.

Signed-off-by: Kees Cook <keescook@chromium.org>
Cc: Marco Stornelli <marco.stornelli@gmail.com>
Cc: Sergiu Iordache <sergiu@chromium.org>
Cc: Seiji Aguchi <seiji.aguchi@hds.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

ramoops: fix use of rounddown_pow_of_two()

The return value of rounddown_pow_of_two wasn't evaluated, so the
operation was a no-op.

Signed-off-by: Marco Stornelli <marco.stornelli@gmail.com>
Reported-by: Andrew Morton <akpm@linux-foundation.org>
Reviewed-by: WANG Cong <xiyou.wangcong@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

c/r: prctl: add PR_SET_MM codes to set up mm_struct entries

When we restore a task we need to set up text, data and data heap sizes
from userspace to the values a task had at checkpoint time.  This patch
adds auxilary prctl codes for that.

While most of them have a statistical nature (their values are involved
into calculation of /proc/<pid>/statm output) the start_brk and brk values
are used to compute an allowed size of program data segment expansion.
Which means an arbitrary changes of this values might be dangerous
operation.  So to restrict access the following requirements applied to
prctl calls:

 - The process has to have CAP_SYS_ADMIN capability granted.
 - For all opcodes except start_brk/brk members an appropriate
   VMA area must exist and should fit certain VMA flags,
   such as:
   - code segment must be executable but not writable;
   - data segment must not be executable.

start_brk/brk values must not intersect with data segment and must not
exceed RLIMIT_DATA resource limit.

Still the main guard is CAP_SYS_ADMIN capability check.

Note the kernel should be compiled with CONFIG_CHECKPOINT_RESTORE support
otherwise these prctl calls will return -EINVAL.

[akpm@linux-foundation.org: cache current->mm in a local, saving 200 bytes text]
Signed-off-by: Cyrill Gorcunov <gorcunov@openvz.org>
Reviewed-by: Kees Cook <keescook@chromium.org>
Cc: Tejun Heo <tj@kernel.org>
Cc: Andrew Vagin <avagin@openvz.org>
Cc: Serge Hallyn <serge.hallyn@canonical.com>
Cc: Pavel Emelyanov <xemul@parallels.com>
Cc: Vasiliy Kulikov <segoon@openwall.com>
Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Michael Kerrisk <mtk.manpages@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

c/r: procfs: add start_data, end_data, start_brk members to /proc/$pid/stat v4

The mm->start_code/end_code, mm->start_data/end_data, mm->start_brk are
involved into calculation of program text/data segment sizes (which might
be seen in /proc/<pid>/statm) and into brk() call final address.

For restore we need to know all these values.  While
mm->start_code/end_code already present in /proc/$pid/stat, the rest
members are not, so this patch brings them in.

The restore procedure of these members is addressed in another patch using
prctl().

Signed-off-by: Cyrill Gorcunov <gorcunov@openvz.org>
Acked-by: Serge Hallyn <serge.hallyn@canonical.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Reviewed-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Alexey Dobriyan <adobriyan@gmail.com>
Cc: Tejun Heo <tj@kernel.org>
Cc: Andrew Vagin <avagin@openvz.org>
Cc: Vasiliy Kulikov <segoon@openwall.com>
Cc: Alexey Dobriyan <adobriyan@gmail.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>