GitHub/exynos8895/android_kernel_samsung_universal8895.git
13 years agoixgb: convert to set_phys_id
Jeff Kirsher [Tue, 3 May 2011 05:17:34 +0000 (05:17 +0000)]
ixgb: convert to set_phys_id

Based on the original patch sent by Stephen Hemminger.

This version incorporates the ethtool changes that Bruce Allan
submitted.

CC: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Tested-by: Evan Swanson <evan.swanson@intel.com>
13 years agoe100: fix build warning
Emil Tantilov [Wed, 27 Apr 2011 08:51:29 +0000 (08:51 +0000)]
e100: fix build warning

In function 'e100_hw_init':
warning: 'err' may be used uninitialized in this function

Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
13 years agonet: dont hold rtnl mutex during netlink dump callbacks
Eric Dumazet [Wed, 27 Apr 2011 22:56:07 +0000 (22:56 +0000)]
net: dont hold rtnl mutex during netlink dump callbacks

Four years ago, Patrick made a change to hold rtnl mutex during netlink
dump callbacks.

I believe it was a wrong move. This slows down concurrent dumps, making
good old /proc/net/ files faster than rtnetlink in some situations.

This occurred to me because one "ip link show dev ..." was _very_ slow
on a workload adding/removing network devices in background.

All dump callbacks are able to use RCU locking now, so this patch does
roughly a revert of commits :

1c2d670f366 : [RTNETLINK]: Hold rtnl_mutex during netlink dump callbacks
6313c1e0992 : [RTNETLINK]: Remove unnecessary locking in dump callbacks

This let writers fight for rtnl mutex and readers going full speed.

It also takes care of phonet : phonet_route_get() is now called from rcu
read section. I renamed it to phonet_route_get_rcu()

Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Patrick McHardy <kaber@trash.net>
Cc: Remi Denis-Courmont <remi.denis-courmont@nokia.com>
Acked-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
13 years agoMerge branch 'batman-adv/next' of git://git.open-mesh.org/ecsv/linux-merge
David S. Miller [Mon, 2 May 2011 22:04:46 +0000 (15:04 -0700)]
Merge branch 'batman-adv/next' of git://git.open-mesh.org/ecsv/linux-merge

13 years agoipv4: Make sure flowi4->{saddr,daddr} are always set.
David S. Miller [Mon, 2 May 2011 21:37:45 +0000 (14:37 -0700)]
ipv4: Make sure flowi4->{saddr,daddr} are always set.

Slow path output route resolution always makes sure that
->{saddr,daddr} are set, and also if we trigger into IPSEC resolution
we initialize them as well, because xfrm_lookup() expects them to be
fully resolved.

But if we hit the fast path and flowi4->flowi4_proto is zero, we won't
do this initialization.

Therefore, move the IPSEC path initialization to the route cache
lookup fast path to make sure these are always set.

Signed-off-by: David S. Miller <davem@davemloft.net>
13 years agobatman-adv: Make bat_priv->primary_if an rcu protected pointer
Marek Lindner [Wed, 20 Apr 2011 13:40:58 +0000 (15:40 +0200)]
batman-adv: Make bat_priv->primary_if an rcu protected pointer

The rcu protected macros rcu_dereference() and rcu_assign_pointer()
for the bat_priv->primary_if need to be used, as well as spin/rcu locking.

Otherwise we might end up using a primary_if pointer pointing to already
freed memory.

Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
13 years agobatman-adv: fix gw_node_update() and gw_election()
Antonio Quartulli [Mon, 25 Apr 2011 20:44:32 +0000 (22:44 +0200)]
batman-adv: fix gw_node_update() and gw_election()

This is a regression from c4aac1ab9b973798163b34939b522f01e4d28ac9

- gw_node_update() doesn't add a new gw_node in case of empty curr_gw.
This means that at the beginning no gw_node is added, leading to an
empty gateway list.

- gw_election() is terminating in case of curr_gw == NULL. It has to
terminate in case of curr_gw != NULL

Signed-off-by: Antonio Quartulli <ordex@autistici.org>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
13 years agobatman-adv: Move definition of atomic_dec_not_zero() into main.h
Antonio Quartulli [Wed, 20 Apr 2011 07:52:56 +0000 (09:52 +0200)]
batman-adv: Move definition of atomic_dec_not_zero() into main.h

atomic_dec_not_zero() is very useful and it is currently defined
multiple times. So it is possible to move it in main.h

Signed-off-by: Antonio Quartulli <ordex@autistici.org>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
13 years agobatman-adv: orig_hash_find() manages rcu_lock/unlock internally
Antonio Quartulli [Sat, 16 Apr 2011 09:30:57 +0000 (11:30 +0200)]
batman-adv: orig_hash_find() manages rcu_lock/unlock internally

orig_hash_find() manages rcu_lock/unlock internally and doesn't need to
be surrounded by rcu_read_lock() / rcu_read_unlock() anymore

Signed-off-by: Antonio Quartulli <ordex@autistici.org>
Acked-by: Marek Lindner <lindner_marek@yahoo.de>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
13 years agonet/igb/e1000/e1000e: more robust ethtool duplex/speed configuration
David Decotigny [Wed, 27 Apr 2011 18:32:43 +0000 (18:32 +0000)]
net/igb/e1000/e1000e: more robust ethtool duplex/speed configuration

This makes sure that one cannot request a 99Mbps full-duplex and get a
100Mbps half-duplex configuration in return due to the way the
speed/duplex parameters are handled internally.

Tested: e1000 works
Signed-off-by: David Decotigny <decot@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
13 years agotulip/de2104x: don't report different speeds depending on port type
David Decotigny [Wed, 27 Apr 2011 18:32:42 +0000 (18:32 +0000)]
tulip/de2104x: don't report different speeds depending on port type

Initial driver reported different speeds depending on the port being
used. This advertises the speed to be 10Mbps in any case, which is
what it actually is on the wire.

Signed-off-by: David Decotigny <decot@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
13 years agoacenic: Fix using the specified speed when configuring NIC
David Decotigny [Wed, 27 Apr 2011 18:32:41 +0000 (18:32 +0000)]
acenic: Fix using the specified speed when configuring NIC

This tells the NIC to take the speed specified by ethtool into account
when configuring the NIC, instead of keeping the previous speed.

Signed-off-by: David Decotigny <decot@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
13 years agoethtool: cosmetic: Use ethtool ethtool_cmd_speed API
David Decotigny [Wed, 27 Apr 2011 18:32:40 +0000 (18:32 +0000)]
ethtool: cosmetic: Use ethtool ethtool_cmd_speed API

This updates the network drivers so that they don't access the
ethtool_cmd::speed field directly, but use ethtool_cmd_speed()
instead.

For most of the drivers, these changes are purely cosmetic and don't
fix any problem, such as for those 1GbE/10GbE drivers that indirectly
call their own ethtool get_settings()/mii_ethtool_gset(). The changes
are meant to enforce code consistency and provide robustness with
future larger throughputs, at the expense of a few CPU cycles for each
ethtool operation.

All drivers compiled with make allyesconfig ion x86_64 have been
updated.

Tested: make allyesconfig on x86_64 + e1000e/bnx2x work
Signed-off-by: David Decotigny <decot@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
13 years agoethtool: Use full 32 bit speed range in ethtool's set_settings
David Decotigny [Wed, 27 Apr 2011 18:32:39 +0000 (18:32 +0000)]
ethtool: Use full 32 bit speed range in ethtool's set_settings

This makes sure the ethtool's set_settings() callback of network
drivers don't ignore the 16 most significant bits when ethtool calls
their set_settings().

All drivers compiled with make allyesconfig on x86_64 have been
updated.

Signed-off-by: David Decotigny <decot@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
13 years agoethtool: Call ethtool's get/set_settings callbacks with cleaned data
David Decotigny [Wed, 27 Apr 2011 18:32:38 +0000 (18:32 +0000)]
ethtool: Call ethtool's get/set_settings callbacks with cleaned data

This makes sure that when a driver calls the ethtool's
get/set_settings() callback of another driver, the data passed to it
is clean. This guarantees that speed_hi will be zeroed correctly if
the called callback doesn't explicitely set it: we are sure we don't
get a corrupted speed from the underlying driver. We also take care of
setting the cmd field appropriately (ETHTOOL_GSET/SSET).

This applies to dev_ethtool_get_settings(), which now makes sure it
sets up that ethtool command parameter correctly before passing it to
drivers. This also means that whoever calls dev_ethtool_get_settings()
does not have to clean the ethtool command parameter. This function
also becomes an exported symbol instead of an inline.

All drivers visible to make allyesconfig under x86_64 have been
updated.

Signed-off-by: David Decotigny <decot@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
13 years agoethtool: cosmetics: enforce const-ness in ethtool_cmd_speed
David Decotigny [Wed, 27 Apr 2011 18:32:37 +0000 (18:32 +0000)]
ethtool: cosmetics: enforce const-ness in ethtool_cmd_speed

The 'ep' argument of ethtool_cmd_speed is not altered: advertise it in
protoype. +Indentation fix. Also add comments to advise using the
ethtool_cmd_speed API to get/set the link speed.

Signed-off-by: David Decotigny <decot@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
13 years agoqlcnic: Support for GBE port settings
Sony Chacko [Thu, 28 Apr 2011 11:48:19 +0000 (11:48 +0000)]
qlcnic: Support for GBE port settings

Enable setting speed and auto negotiation parameters for GbE ports.
Hardware do not support half duplex setting currently.

o Update driver version to 5.0.17.

Signed-off-by: Sony Chacko <sony.chacko@qlogic.com>
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
13 years agoqlcnic: support rcv ring configuration through ethtool
Sucheta Chakraborty [Thu, 28 Apr 2011 11:48:18 +0000 (11:48 +0000)]
qlcnic: support rcv ring configuration through ethtool

o Support ethtool command ETHTOOL_GCHANNELS and ETHTOOL_SCHANNELS.
o Number of rcv rings configuration depend upon number of msix vector.

Signed-off-by: Sucheta Chakraborty <sucheta.chakraborty@qlogic.com>
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
13 years agoipv4, ipv6, bonding: Restore control over number of peer notifications
Ben Hutchings [Tue, 26 Apr 2011 15:25:52 +0000 (15:25 +0000)]
ipv4, ipv6, bonding: Restore control over number of peer notifications

For backward compatibility, we should retain the module parameters and
sysfs attributes to control the number of peer notifications
(gratuitous ARPs and unsolicited NAs) sent after bonding failover.
Also, it is possible for failover to take place even though the new
active slave does not have link up, and in that case the peer
notification should be deferred until it does.

Change ipv4 and ipv6 so they do not automatically send peer
notifications on bonding failover.

Change the bonding driver to send separate NETDEV_NOTIFY_PEERS
notifications when the link is up, as many times as requested.  Since
it does not directly control which protocols send notifications, make
num_grat_arp and num_unsol_na aliases for a single parameter.  Bump
the bonding version number and update its documentation.

Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Acked-by: Brian Haley <brian.haley@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
13 years agopktgen: create num frags requested
amit salecha [Fri, 22 Apr 2011 16:22:20 +0000 (16:22 +0000)]
pktgen: create num frags requested

Pktgen doesn't generate number of frags requested.
Divide packet size by number of frags and fill that in every frags.

Example:
With packet size 1470, it generate only 11 frags. Initial frags
get lenght 706, 353, 177....so on. Last frag get divided by 2.

Now with this fix, each frags will get 78 bytes.

Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
13 years agobpf: depends on MODULES
Eric Dumazet [Fri, 29 Apr 2011 17:20:53 +0000 (10:20 -0700)]
bpf: depends on MODULES

module_alloc() and module_free() are available only if CONFIG_MODULES=y

Reported-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
13 years agoipv4: Get route daddr from flow key in l2tp_ip_connect().
David S. Miller [Fri, 29 Apr 2011 06:50:49 +0000 (23:50 -0700)]
ipv4: Get route daddr from flow key in l2tp_ip_connect().

Now that output route lookups update the flow with
destination address selection, we can fetch it from
fl4->daddr instead of rt->rt_dst

Signed-off-by: David S. Miller <davem@davemloft.net>
13 years agoipv4: Get route daddr from flow key in tcp_v4_connect().
David S. Miller [Fri, 29 Apr 2011 06:50:32 +0000 (23:50 -0700)]
ipv4: Get route daddr from flow key in tcp_v4_connect().

Now that output route lookups update the flow with
destination address selection, we can fetch it from
fl4->daddr instead of rt->rt_dst

Signed-off-by: David S. Miller <davem@davemloft.net>
13 years agoipv4: Get route daddr from flow key in inet_csk_route_req().
David S. Miller [Fri, 29 Apr 2011 06:50:09 +0000 (23:50 -0700)]
ipv4: Get route daddr from flow key in inet_csk_route_req().

Now that output route lookups update the flow with
destination address selection, we can fetch it from
fl4->daddr instead of rt->rt_dst

Signed-off-by: David S. Miller <davem@davemloft.net>
13 years agoipv4: Get route daddr from flow key in ip4_datagram_connect().
David S. Miller [Fri, 29 Apr 2011 06:49:45 +0000 (23:49 -0700)]
ipv4: Get route daddr from flow key in ip4_datagram_connect().

Now that output route lookups update the flow with
destination address selection, we can fetch it from
fl4->daddr instead of rt->rt_dst

Signed-off-by: David S. Miller <davem@davemloft.net>
13 years agoipv4: Get route daddr from flow key in dccp_v4_connect().
David S. Miller [Fri, 29 Apr 2011 06:49:30 +0000 (23:49 -0700)]
ipv4: Get route daddr from flow key in dccp_v4_connect().

Now that output route lookups update the flow with
destination address selection, we can fetch it from
fl4->daddr instead of rt->rt_dst

Signed-off-by: David S. Miller <davem@davemloft.net>
13 years agoipv4: Fetch route saddr from flow key in l2tp_ip_connect().
David S. Miller [Fri, 29 Apr 2011 06:17:58 +0000 (23:17 -0700)]
ipv4: Fetch route saddr from flow key in l2tp_ip_connect().

Now that output route lookups update the flow with
source address selection, we can fetch it from
fl4->saddr instead of rt->rt_src

Signed-off-by: David S. Miller <davem@davemloft.net>
13 years agoipv4: Fetch route saddr from flow key in tcp_v4_connect().
David S. Miller [Fri, 29 Apr 2011 06:17:31 +0000 (23:17 -0700)]
ipv4: Fetch route saddr from flow key in tcp_v4_connect().

Now that output route lookups update the flow with
source address selection, we can fetch it from
fl4->saddr instead of rt->rt_src

Signed-off-by: David S. Miller <davem@davemloft.net>
13 years agoipv4: Fetch route saddr from flow key in ip4_datagram_connect().
David S. Miller [Fri, 29 Apr 2011 06:17:16 +0000 (23:17 -0700)]
ipv4: Fetch route saddr from flow key in ip4_datagram_connect().

Now that output route lookups update the flow with
source address selection, we can fetch it from
fl4->saddr instead of rt->rt_src

Signed-off-by: David S. Miller <davem@davemloft.net>
13 years agoipv4: Fetch route saddr from flow key in inet_sk_reselect_saddr().
David S. Miller [Fri, 29 Apr 2011 06:16:53 +0000 (23:16 -0700)]
ipv4: Fetch route saddr from flow key in inet_sk_reselect_saddr().

Now that output route lookups update the flow with
source address selection, we can fetch it from
fl4->saddr instead of rt->rt_src

Signed-off-by: David S. Miller <davem@davemloft.net>
13 years agoipv4: Remove now superfluous code in ip_route_connect().
David S. Miller [Fri, 29 Apr 2011 06:13:17 +0000 (23:13 -0700)]
ipv4: Remove now superfluous code in ip_route_connect().

Now that output route lookups update the flow with
source address et al. selections, the fl4->{saddr,daddr}
assignments here are no longer necessary.

Signed-off-by: David S. Miller <davem@davemloft.net>
13 years agoipv4: Use caller's on-stack flowi as-is in output route lookups.
David S. Miller [Thu, 28 Apr 2011 21:48:42 +0000 (14:48 -0700)]
ipv4: Use caller's on-stack flowi as-is in output route lookups.

Signed-off-by: David S. Miller <davem@davemloft.net>
13 years agonet: Use non-zero allocations in dst_alloc().
David S. Miller [Thu, 28 Apr 2011 21:31:47 +0000 (14:31 -0700)]
net: Use non-zero allocations in dst_alloc().

Make dst_alloc() and it's users explicitly initialize the entire
entry.

The zero'ing done by kmem_cache_zalloc() was almost entirely
redundant.

Signed-off-by: David S. Miller <davem@davemloft.net>
13 years agonet: Make dst_alloc() take more explicit initializations.
David S. Miller [Thu, 28 Apr 2011 21:13:38 +0000 (14:13 -0700)]
net: Make dst_alloc() take more explicit initializations.

Now the dst->dev, dev->obsolete, and dst->flags values can
be specified as well.

Signed-off-by: David S. Miller <davem@davemloft.net>
13 years agol2tp: Fix inet_opt conversion.
David S. Miller [Thu, 28 Apr 2011 20:54:06 +0000 (13:54 -0700)]
l2tp: Fix inet_opt conversion.

We don't actually hold the socket lock at this point, so the
rcu_dereference_protected() isn't' correct.  Thanks to Eric
Dumazet for pointing this out.

Thankfully, we're only interested in fetching the faddr value
if srr is enabled, so we can simply make this an RCU sequence
and use plain rcu_dereference().

Reported-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
13 years agonet: ibmveth: force reconfiguring checksum settings on startup
Michał Mirosław [Thu, 28 Apr 2011 01:59:15 +0000 (11:59 +1000)]
net: ibmveth: force reconfiguring checksum settings on startup

Commit b9367bf3ee6d ("net: ibmveth: convert to hw_features") accidentally
removed call to ibmveth_set_csum_offload() in ibmveth_probe(). Put the
call back where it was, but with additional error checking provided
by ibmveth_set_features().

Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
[sfr: dev -> netdev]
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
13 years agoqlcnic: fix memory leak in qlcnic_blink_led.
Sucheta Chakraborty [Wed, 27 Apr 2011 14:43:44 +0000 (14:43 +0000)]
qlcnic: fix memory leak in qlcnic_blink_led.

o Memory allocated in ETHTOOL_ACTIVE mode, is not getting freed. So,
  in ETHTOOL_ID_INACTIVE mode, return after freeing allocated memory.
o Using set bit instead of blink_down field, as it is also required
  in internal Loopback test and etc.

Signed-off-by: Sucheta Chakraborty <sucheta.chakraborty@qlogic.com>
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
13 years agotg3: Convert u32 flag,flg2,flg3 uses to bitmap
Joe Perches [Tue, 26 Apr 2011 08:12:10 +0000 (08:12 +0000)]
tg3: Convert u32 flag,flg2,flg3 uses to bitmap

Using a bitmap instead of separate u32 flags allows a consistent, simpler
and more extensible mechanism to determine capabilities.

Convert bitmasks to enum.
Add tg3_flag, tg3_flag_clear and tg3_flag_set.
Convert the flag & bitmask tests.

Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
13 years agonet: allow user to change NETIF_F_HIGHDMA
Michał Mirosław [Fri, 22 Apr 2011 06:31:16 +0000 (06:31 +0000)]
net: allow user to change NETIF_F_HIGHDMA

NETIF_F_HIGHDMA is like any other TX offloads, so allow user to toggle it.
This is needed later for bridge and bonding convertsion to hw_features.

Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
13 years agobridge: convert br_features_recompute() to ndo_fix_features
Michał Mirosław [Fri, 22 Apr 2011 06:31:16 +0000 (06:31 +0000)]
bridge: convert br_features_recompute() to ndo_fix_features

Note: netdev_update_features() needs only rtnl_lock as br->port_list
is only changed while holding it.

Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
13 years agonet: fix netdev_increment_features()
Michał Mirosław [Fri, 22 Apr 2011 06:31:16 +0000 (06:31 +0000)]
net: fix netdev_increment_features()

Simplify and fix netdev_increment_features() to conform to what is
stated in netdevice.h comments about NETIF_F_ONE_FOR_ALL.
Include FCoE segmentation and VLAN-challedged flags in computation.

Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
13 years agonet:use help function of skb_checksum_start_offset to calculate offset
Shan Wei [Fri, 22 Apr 2011 11:07:41 +0000 (19:07 +0800)]
net:use help function of skb_checksum_start_offset to calculate offset

Although these are equivalent, but the skb_checksum_start_offset() is more readable.

Signed-off-by: Shan Wei <shanwei@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
13 years agoinet: add RCU protection to inet->opt
Eric Dumazet [Thu, 21 Apr 2011 09:45:37 +0000 (09:45 +0000)]
inet: add RCU protection to inet->opt

We lack proper synchronization to manipulate inet->opt ip_options

Problem is ip_make_skb() calls ip_setup_cork() and
ip_setup_cork() possibly makes a copy of ipc->opt (struct ip_options),
without any protection against another thread manipulating inet->opt.

Another thread can change inet->opt pointer and free old one under us.

Use RCU to protect inet->opt (changed to inet->inet_opt).

Instead of handling atomic refcounts, just copy ip_options when
necessary, to avoid cache line dirtying.

We cant insert an rcu_head in struct ip_options since its included in
skb->cb[], so this patch is large because I had to introduce a new
ip_options_rcu structure.

Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
13 years agonet: filter: Just In Time compiler for x86-64
Eric Dumazet [Wed, 20 Apr 2011 09:27:32 +0000 (09:27 +0000)]
net: filter: Just In Time compiler for x86-64

In order to speedup packet filtering, here is an implementation of a
JIT compiler for x86_64

It is disabled by default, and must be enabled by the admin.

echo 1 >/proc/sys/net/core/bpf_jit_enable

It uses module_alloc() and module_free() to get memory in the 2GB text
kernel range since we call helpers functions from the generated code.

EAX : BPF A accumulator
EBX : BPF X accumulator
RDI : pointer to skb   (first argument given to JIT function)
RBP : frame pointer (even if CONFIG_FRAME_POINTER=n)
r9d : skb->len - skb->data_len (headlen)
r8  : skb->data

To get a trace of generated code, use :

echo 2 >/proc/sys/net/core/bpf_jit_enable

Example of generated code :

# tcpdump -p -n -s 0 -i eth1 host 192.168.20.0/24

flen=18 proglen=147 pass=3 image=ffffffffa00b5000
JIT code: ffffffffa00b5000: 55 48 89 e5 48 83 ec 60 48 89 5d f8 44 8b 4f 60
JIT code: ffffffffa00b5010: 44 2b 4f 64 4c 8b 87 b8 00 00 00 be 0c 00 00 00
JIT code: ffffffffa00b5020: e8 24 7b f7 e0 3d 00 08 00 00 75 28 be 1a 00 00
JIT code: ffffffffa00b5030: 00 e8 fe 7a f7 e0 24 00 3d 00 14 a8 c0 74 49 be
JIT code: ffffffffa00b5040: 1e 00 00 00 e8 eb 7a f7 e0 24 00 3d 00 14 a8 c0
JIT code: ffffffffa00b5050: 74 36 eb 3b 3d 06 08 00 00 74 07 3d 35 80 00 00
JIT code: ffffffffa00b5060: 75 2d be 1c 00 00 00 e8 c8 7a f7 e0 24 00 3d 00
JIT code: ffffffffa00b5070: 14 a8 c0 74 13 be 26 00 00 00 e8 b5 7a f7 e0 24
JIT code: ffffffffa00b5080: 00 3d 00 14 a8 c0 75 07 b8 ff ff 00 00 eb 02 31
JIT code: ffffffffa00b5090: c0 c9 c3

BPF program is 144 bytes long, so native program is almost same size ;)

(000) ldh      [12]
(001) jeq      #0x800           jt 2    jf 8
(002) ld       [26]
(003) and      #0xffffff00
(004) jeq      #0xc0a81400      jt 16   jf 5
(005) ld       [30]
(006) and      #0xffffff00
(007) jeq      #0xc0a81400      jt 16   jf 17
(008) jeq      #0x806           jt 10   jf 9
(009) jeq      #0x8035          jt 10   jf 17
(010) ld       [28]
(011) and      #0xffffff00
(012) jeq      #0xc0a81400      jt 16   jf 13
(013) ld       [38]
(014) and      #0xffffff00
(015) jeq      #0xc0a81400      jt 16   jf 17
(016) ret      #65535
(017) ret      #0

Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Arnaldo Carvalho de Melo <acme@infradead.org>
Cc: Ben Hutchings <bhutchings@solarflare.com>
Cc: Hagen Paul Pfeifer <hagen@jauu.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
13 years agoipv4: Kill RTO_CONN.
David S. Miller [Tue, 26 Apr 2011 21:58:35 +0000 (14:58 -0700)]
ipv4: Kill RTO_CONN.

It's not used by anything in the kernel, and defined in net/route.h so
never exported to userspace.

Therefore we can safely remove it.

Signed-off-by: David S. Miller <davem@davemloft.net>
13 years agoipv4: Remove erroneous check in igmpv3_newpack() and igmp_send_report().
David S. Miller [Tue, 26 Apr 2011 20:57:47 +0000 (13:57 -0700)]
ipv4: Remove erroneous check in igmpv3_newpack() and igmp_send_report().

Output route resolution never returns a route with rt_src set to zero
(which is INADDR_ANY).

Even if the flow key for the output route lookup specifies INADDR_ANY
for the source address, the output route resolution chooses a real
source address to use in the final route.

This test has existed forever in igmp_send_report() and David Stevens
simply copied over the erroneous test when implementing support for
IGMPv3.

Signed-off-by: David S. Miller <davem@davemloft.net>
Reviewed-by: Eric Dumazet <eric.dumazet@gmail.com>
13 years agoipv4: Sanitize and simplify ip_route_{connect,newports}()
David S. Miller [Tue, 26 Apr 2011 20:28:44 +0000 (13:28 -0700)]
ipv4: Sanitize and simplify ip_route_{connect,newports}()

These functions are used together as a unit for route resolution
during connect().  They address the chicken-and-egg problem that
exists when ports need to be allocated during connect() processing,
yet such port allocations require addressing information from the
routing code.

It's currently more heavy handed than it needs to be, and in
particular we allocate and initialize a flow object twice.

Let the callers provide the on-stack flow object.  That way we only
need to initialize it once in the ip_route_connect() call.

Later, if ip_route_newports() needs to do anything, it re-uses that
flow object as-is except for the ports which it updates before the
route re-lookup.

Also, describe why this set of facilities are needed and how it works
in a big comment.

Signed-off-by: David S. Miller <davem@davemloft.net>
Reviewed-by: Eric Dumazet <eric.dumazet@gmail.com>
13 years agor8169: fix merge conflict fix.
Francois Romieu [Wed, 27 Apr 2011 20:52:22 +0000 (13:52 -0700)]
r8169: fix merge conflict fix.

- use adequate MAC_VER id
  (see 01dc7fec4025f6bb72b6b98ec88b375346b6dbbb)
- remove duplicate rtl_firmware_info record
- remove duplicate functions

Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Cc: Realtek linux nic maintainers <nic_swsd@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
13 years agosctp: clean up route lookup calls
Vlad Yasevich [Tue, 26 Apr 2011 21:54:17 +0000 (21:54 +0000)]
sctp: clean up route lookup calls

Change the call to take the transport parameter and set the
cached 'dst' appropriately inside the get_dst() function calls.

This will allow us in the future  to clean up source address
storage as well.

Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: Wei Yongjun <yjwei@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
13 years agosctp: remove useless arguments from get_saddr() call
Vlad Yasevich [Tue, 26 Apr 2011 21:53:20 +0000 (21:53 +0000)]
sctp: remove useless arguments from get_saddr() call

There is no point in passing a destination address to
a get_saddr() call.

Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: Wei Yongjun <yjwei@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
13 years agosctp: make sctp over IPv6 work with IPsec
Vlad Yasevich [Tue, 26 Apr 2011 21:52:27 +0000 (21:52 +0000)]
sctp: make sctp over IPv6 work with IPsec

SCTP never called xfrm_output after it's v6 route lookups so
that never really worked with ipsec.  Additioanlly, we never
passed port nubmers and protocol in the flowi, so any port
based policies were never applied as well.  Now that we can
fixed ipv6 routing lookup code, using ip6_dst_lookup_flow()
and pass port numbers.

Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: Wei Yongjun <yjwei@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
13 years agosctp: cache the ipv6 source after route lookup
Vlad Yasevich [Tue, 26 Apr 2011 21:51:31 +0000 (21:51 +0000)]
sctp: cache the ipv6 source after route lookup

The ipv6 routing lookup does give us a source address,
but instead of filling it into the dst, it's stored in
the flowi.  We can use that instead of going through the
entire source address selection again.
Also the useless ->dst_saddr member of sctp_pf is removed.
And sctp_v6_dst_saddr() is removed, instead by introduce
sctp_v6_to_addr(), which can be reused to cleanup some dup
code.

Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: Wei Yongjun <yjwei@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
13 years agosctp: fix sctp to work with ipv6 source address routing
Weixing Shi [Tue, 26 Apr 2011 21:36:32 +0000 (21:36 +0000)]
sctp: fix sctp to work with ipv6 source address routing

In the below test case, using the source address routing,
sctp can not work.
Node-A
1)ifconfig eth0 inet6 add 2001:1::1/64
2)ip -6 rule add from 2001:1::1 table 100 pref 100
3)ip -6 route add 2001:2::1 dev eth0 table 100
4)sctp_darn -H 2001:1::1 -P 250 -l &
Node-B
1)ifconfig eth0 inet6 add 2001:2::1/64
2)ip -6 rule add from 2001:2::1 table 100 pref 100
3)ip -6 route add 2001:1::1 dev eth0 table 100
4)sctp_darn -H 2001:2::1 -P 250 -h 2001:1::1 -p 250 -s

root cause:
Node-A and Node-B use the source address routing, and
at begining, source address will be NULL,sctp will
search the  routing table by the destination address,
because using the source address routing table, and
the result dst_entry will be NULL.

solution:
walk through the bind address list to get the source
address and then lookup the routing table again to get
the correct dst_entry.

Signed-off-by: Weixing Shi <Weixing.Shi@windriver.com>
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: Wei Yongjun <yjwei@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
13 years agoixgbe: convert to ethtool set_phys_id
Emil Tantilov [Sat, 16 Apr 2011 06:12:51 +0000 (06:12 +0000)]
ixgbe: convert to ethtool set_phys_id

Based on the original patch submitted by Stephen Hemminger.

This patch makes the following changes:
- Change ETHTOOL_ID_INACTIVE return value to 2 (blinks/sec)
- Fix restoring of IXGBE_LEDCTL

CC: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Evan Swanson <evan.swanson@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
13 years agoixgbe: fix X540 ethtool loopback test.
Don Skidmore [Sat, 16 Apr 2011 05:29:14 +0000 (05:29 +0000)]
ixgbe: fix X540 ethtool loopback test.

On X540 we need to set the MACC.FLU bit to 1 in order to force the link
up before entering MAC loopback.  This is only used in the ethtool loopback
test, which was failing.  This patch corrects it.

Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Evan Swanson <evan.swanson@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
13 years agoixgbe: Bump version
Don Skidmore [Thu, 14 Apr 2011 07:40:11 +0000 (07:40 +0000)]
ixgbe: Bump version

Bump the driver version number to better match up with the out of tree
driver that has similar functionality.

Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Evan Swanson <evan.swanson@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
13 years agoixgbe: enable SCTP checksum offload for X540
Don Skidmore [Tue, 12 Apr 2011 09:42:11 +0000 (09:42 +0000)]
ixgbe: enable SCTP checksum offload for X540

X540 supports SCTP checksum offload so enable it.  It was overlooked when X540
support was initially added to the driver.

Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Evan Swanson <evan.swanson@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
13 years agoixgbe: do not clear FCoE DDP error status for received ABTS
Yi Zou [Sat, 9 Apr 2011 08:34:12 +0000 (08:34 +0000)]
ixgbe: do not clear FCoE DDP error status for received ABTS

The ddp->err is initialized to be 1 to make sure outstanding DDP context is
guaranteed to be invalidated when HW is not auto-invalidating it. However,
in case of receiving ABTS response for a DDPed I/O, the ddp->err was cleared,
bypassing the invalidating of the DDP context from upper protocol stack when
ixgbe_fcoe_ddp_put() is called. This bug is fixed here by updating the error
only when FCP_RSP is received.

Signed-off-by: Yi Zou <yi.zou@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
13 years agoixgbe: fix static functions
John Fastabend [Tue, 12 Apr 2011 02:44:55 +0000 (02:44 +0000)]
ixgbe: fix static functions

Define functions as static added C=1 (sparse) to my make line
brought these to my attention.

Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
13 years agoixgbe: remove ntuple display support
Alexander Duyck [Sat, 9 Apr 2011 05:34:06 +0000 (05:34 +0000)]
ixgbe: remove ntuple display support

This change removes the ntuple display support from ixgbe.  The reason for
this change is to resolve a number of issues in the way display filtering
is handled.

I plan to add support for displaying these filters via the network flow
classifier interface.

Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Evan Swanson <evan.swanson@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
13 years agoixgbe: add LED blink code for x540
Emil Tantilov [Fri, 8 Apr 2011 01:24:05 +0000 (01:24 +0000)]
ixgbe: add LED blink code for x540

Implement blink_led_start and blink_led_stop functions for x540
using the MACC register.

Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Evan Swanson <evan.swanson@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
13 years agoixgbe: add support for 64k EEPROM for 82599
Emil Tantilov [Fri, 1 Apr 2011 08:17:19 +0000 (08:17 +0000)]
ixgbe: add support for 64k EEPROM for 82599

82599 supports up to 32k EEPROM addressing via EERD register. If we
wish to address larger EEPROM this have to be done via serial interface.
This patch adds function ixgbe_read_eeprom_82599 which selects the best
method to read the EEPROM.

Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Evan Swanson <evan.swanson@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
13 years agoixgbe: register defines cleanup
Emil Tantilov [Thu, 31 Mar 2011 09:36:24 +0000 (09:36 +0000)]
ixgbe: register defines cleanup

Remove duplicates.
Fix incorrect defines.
Fix/Update comments.
Fix whitespace.
Add new register defines.

Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Evan Swanson <evan.swanson@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
13 years agoixgbe: explicitly disable 100H for x540
Emil Tantilov [Thu, 31 Mar 2011 09:36:12 +0000 (09:36 +0000)]
ixgbe: explicitly disable 100H for x540

100H is not supported on this HW, but the bit is set on the PHY.
This can result in link at 100F when advertising only 1000F.

Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Evan Swanson <evan.swanson@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
13 years agoe1000e: implement ethtool set_phys_id
Bruce Allan [Sat, 16 Apr 2011 00:34:40 +0000 (00:34 +0000)]
e1000e: implement ethtool set_phys_id

Based on a patch from Stephen Hemminger <shemminger@vyatta.com>.

The new ethtool set_phys_id takes over controlling the LED for
identifying boards.  This fixes the lockout during that period.
For this device lots of extra infrastructure can also be removed by
using set_phys_id.

v2: - return blink frequency for parts that do not support blink in h/w
    - add blink_led function pointers for devices that do support blink
      in h/w to cleanup the test for this functionality

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Cc: Stephen Hemminger <shemminger@vyatta.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
13 years agoMerge branch 'master' of master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6
David S. Miller [Tue, 26 Apr 2011 19:16:46 +0000 (12:16 -0700)]
Merge branch 'master' of /linux/kernel/git/davem/net-2.6

Resolved logic conflicts causing a build failure due to
drivers/net/r8169.c changes using a patch from Stephen Rothwell.

Signed-off-by: David S. Miller <davem@davemloft.net>
13 years agotg3: Update version to 3.118
Matt Carlson [Mon, 25 Apr 2011 12:42:50 +0000 (12:42 +0000)]
tg3: Update version to 3.118

This patch updates the tg3 version to 3.118.

Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Reviewed-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
13 years agotg3: Whitespace cleanups
Matt Carlson [Mon, 25 Apr 2011 12:42:49 +0000 (12:42 +0000)]
tg3: Whitespace cleanups

This patch gets rid of some harmless whitespace errors.

Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Reviewed-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
13 years agotg3: Add EEH support
Matt Carlson [Mon, 25 Apr 2011 12:42:48 +0000 (12:42 +0000)]
tg3: Add EEH support

This patch adds EEH support to the tg3 driver.

Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Reviewed-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
13 years agotg3: Add TSO loopback test
Matt Carlson [Mon, 25 Apr 2011 12:42:47 +0000 (12:42 +0000)]
tg3: Add TSO loopback test

This patch adds code to exercise the TSO portion of the device through
a phy loopback test.

Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
13 years agotg3: Organize loopback test failure flags
Matt Carlson [Mon, 25 Apr 2011 12:42:46 +0000 (12:42 +0000)]
tg3: Organize loopback test failure flags

As more test modes are added to each loopback mode, the need to
organise the results increases.  This patch groups the results by
loopback mode, and then by test mode.

Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Reviewed-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
13 years agotg3: Fix int generation hw bug for 5719 / 5720
Matt Carlson [Mon, 25 Apr 2011 12:42:45 +0000 (12:42 +0000)]
tg3: Fix int generation hw bug for 5719 / 5720

On the 5719 and 5720, there is a bug where the hardware will
misinterpret a status tag update and leave interrupts permanently
disabled.  This patch enables a hardware fix that works around the
issue.

Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Reviewed-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
13 years agobluetooth: Fix use-before-initiailized var.
David S. Miller [Mon, 25 Apr 2011 20:03:02 +0000 (13:03 -0700)]
bluetooth: Fix use-before-initiailized var.

net/bluetooth/l2cap_core.c: In function ‘l2cap_recv_frame’:
net/bluetooth/l2cap_core.c:3612:15: warning: ‘sk’ may be used uninitialized in this function
net/bluetooth/l2cap_core.c:3612:15: note: ‘sk’ was declared here

Actually the problem is in the inline function l2cap_data_channel(), we
branch to the label 'done' which tests 'sk' before we set it to anything.

Initialize it to NULL to fix this.

Signed-off-by: David S. Miller <davem@davemloft.net>
13 years agoMerge branch 'for-davem' of git://git.kernel.org/pub/scm/linux/kernel/git/linville...
David S. Miller [Mon, 25 Apr 2011 19:46:37 +0000 (12:46 -0700)]
Merge branch 'for-davem' of git://git./linux/kernel/git/linville/wireless-next-2.6

13 years agobe2net: Fixed a bug in be_cmd_get_regs().
Somnath Kotur [Thu, 21 Apr 2011 03:18:12 +0000 (03:18 +0000)]
be2net: Fixed a bug in be_cmd_get_regs().

Same WRB entry was being reused over different iterations of a
loop while issuing non-embedded IOCTL requests.Fixed couple of minor bugs
in this path as well.
Re-factored code to alloc/free memory for DMA outside of loop

Signed-off-by: Somnath Kotur <somnath.kotur@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
13 years agobonding: move processing of recv handlers into handle_frame()
Jiri Pirko [Tue, 19 Apr 2011 03:48:16 +0000 (03:48 +0000)]
bonding: move processing of recv handlers into handle_frame()

Since now when bonding uses rx_handler, all traffic going into bond
device goes thru bond_handle_frame. So there's no need to go back into
bonding code later via ptype handlers. This patch converts
original ptype handlers into "bonding receive probes". These functions
are called from bond_handle_frame and they are registered per-mode.

Note that vlan packets are also handled because they are always untagged
thanks to vlan_untag()

Note that this also allows arpmon for eth-bond-bridge-vlan topology.

Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
13 years agonet: make WARN_ON in dev_disable_lro() useful
Michał Mirosław [Thu, 21 Apr 2011 12:42:15 +0000 (12:42 +0000)]
net: make WARN_ON in dev_disable_lro() useful

Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
13 years agonet: provide cow_metrics() methods to blackhole dst_ops
Held Bernhard [Sun, 24 Apr 2011 22:07:32 +0000 (22:07 +0000)]
net: provide cow_metrics() methods to blackhole dst_ops

Since commit 62fa8a846d7d (net: Implement read-only protection and COW'ing
of metrics.) the kernel throws an oops.

[  101.620985] BUG: unable to handle kernel NULL pointer dereference at
           (null)
[  101.621050] IP: [<          (null)>]           (null)
[  101.621084] PGD 6e53c067 PUD 3dd6a067 PMD 0
[  101.621122] Oops: 0010 [#1] SMP
[  101.621153] last sysfs file: /sys/devices/virtual/ppp/ppp/uevent
[  101.621192] CPU 2
[  101.621206] Modules linked in: l2tp_ppp pppox ppp_generic slhc
l2tp_netlink l2tp_core deflate zlib_deflate twofish_x86_64
twofish_common des_generic cbc ecb sha1_generic hmac af_key
iptable_filter snd_pcm_oss snd_mixer_oss snd_seq snd_seq_device loop
snd_hda_codec_hdmi snd_hda_codec_realtek snd_hda_intel snd_hda_codec
snd_pcm snd_timer snd i2c_i801 iTCO_wdt psmouse soundcore snd_page_alloc
evdev uhci_hcd ehci_hcd thermal
[  101.621552]
[  101.621567] Pid: 5129, comm: openl2tpd Not tainted 2.6.39-rc4-Quad #3
Gigabyte Technology Co., Ltd. G33-DS3R/G33-DS3R
[  101.621637] RIP: 0010:[<0000000000000000>]  [<          (null)>]   (null)
[  101.621684] RSP: 0018:ffff88003ddeba60  EFLAGS: 00010202
[  101.621716] RAX: ffff88003ddb5600 RBX: ffff88003ddb5600 RCX:
0000000000000020
[  101.621758] RDX: ffffffff81a69a00 RSI: ffffffff81b7ee61 RDI:
ffff88003ddb5600
[  101.621800] RBP: ffff8800537cd900 R08: 0000000000000000 R09:
ffff88003ddb5600
[  101.621840] R10: 0000000000000005 R11: 0000000000014b38 R12:
ffff88003ddb5600
[  101.621881] R13: ffffffff81b7e480 R14: ffffffff81b7e8b8 R15:
ffff88003ddebad8
[  101.621924] FS:  00007f06e4182700(0000) GS:ffff88007fd00000(0000)
knlGS:0000000000000000
[  101.621971] CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[  101.622005] CR2: 0000000000000000 CR3: 0000000045274000 CR4:
00000000000006e0
[  101.622046] DR0: 0000000000000000 DR1: 0000000000000000 DR2:
0000000000000000
[  101.622087] DR3: 0000000000000000 DR6: 00000000ffff0ff0 DR7:
0000000000000400
[  101.622129] Process openl2tpd (pid: 5129, threadinfo
ffff88003ddea000, task ffff88003de9a280)
[  101.622177] Stack:
[  101.622191]  ffffffff81447efa ffff88007d3ded80 ffff88003de9a280
ffff88007d3ded80
[  101.622245]  0000000000000001 ffff88003ddebbb8 ffffffff8148d5a7
0000000000000212
[  101.622299]  ffff88003dcea000 ffff88003dcea188 ffffffff00000001
ffffffff81b7e480
[  101.622353] Call Trace:
[  101.622374]  [<ffffffff81447efa>] ? ipv4_blackhole_route+0x1ba/0x210
[  101.622415]  [<ffffffff8148d5a7>] ? xfrm_lookup+0x417/0x510
[  101.622450]  [<ffffffff8127672a>] ? extract_buf+0x9a/0x140
[  101.622485]  [<ffffffff8144c6a0>] ? __ip_flush_pending_frames+0x70/0x70
[  101.622526]  [<ffffffff8146fbbf>] ? udp_sendmsg+0x62f/0x810
[  101.622562]  [<ffffffff813f98a6>] ? sock_sendmsg+0x116/0x130
[  101.622599]  [<ffffffff8109df58>] ? find_get_page+0x18/0x90
[  101.622633]  [<ffffffff8109fd6a>] ? filemap_fault+0x12a/0x4b0
[  101.622668]  [<ffffffff813fb5c4>] ? move_addr_to_kernel+0x64/0x90
[  101.622706]  [<ffffffff81405d5a>] ? verify_iovec+0x7a/0xf0
[  101.622739]  [<ffffffff813fc772>] ? sys_sendmsg+0x292/0x420
[  101.622774]  [<ffffffff810b994a>] ? handle_pte_fault+0x8a/0x7c0
[  101.622810]  [<ffffffff810b76fe>] ? __pte_alloc+0xae/0x130
[  101.622844]  [<ffffffff810ba2f8>] ? handle_mm_fault+0x138/0x380
[  101.622880]  [<ffffffff81024af9>] ? do_page_fault+0x189/0x410
[  101.622915]  [<ffffffff813fbe03>] ? sys_getsockname+0xf3/0x110
[  101.622952]  [<ffffffff81450c4d>] ? ip_setsockopt+0x4d/0xa0
[  101.622986]  [<ffffffff813f9932>] ? sockfd_lookup_light+0x22/0x90
[  101.623024]  [<ffffffff814b61fb>] ? system_call_fastpath+0x16/0x1b
[  101.623060] Code:  Bad RIP value.
[  101.623090] RIP  [<          (null)>]           (null)
[  101.623125]  RSP <ffff88003ddeba60>
[  101.623146] CR2: 0000000000000000
[  101.650871] ---[ end trace ca3856a7d8e8dad4 ]---
[  101.651011] __sk_free: optmem leakage (160 bytes) detected.

The oops happens in dst_metrics_write_ptr()
include/net/dst.h:124: return dst->ops->cow_metrics(dst, p);

dst->ops->cow_metrics is NULL and causes the oops.

Provide cow_metrics() methods, like we did in commit 214f45c91bb
(net: provide default_advmss() methods to blackhole dst_ops)

Signed-off-by: Held Bernhard <berny156@gmx.de>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
13 years agoMerge branch 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/linville/wirel...
John W. Linville [Mon, 25 Apr 2011 18:34:25 +0000 (14:34 -0400)]
Merge branch 'master' of git://git./linux/kernel/git/linville/wireless-next-2.6 into for-davem

Conflicts:
drivers/net/wireless/iwlwifi/iwl-core.c
drivers/net/wireless/rt2x00/rt2x00queue.c
drivers/net/wireless/rt2x00/rt2x00queue.h

13 years agocdc_ncm: fix short packet issue on some devices
Hans Petter Selasky [Mon, 25 Apr 2011 05:35:19 +0000 (22:35 -0700)]
cdc_ncm: fix short packet issue on some devices

The default maximum transmit length for NCM USB frames should be so
that a short packet happens at the end if the device supports a length
greater than the defined maximum. This is achieved by adding 4 bytes
to the maximum length so that the existing logic can fit a short
packet there.

Signed-off-by: Hans Petter Selasky <hselasky@c2i.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
13 years agoMerge branch 'davem.r8169' of git://git.kernel.org/pub/scm/linux/kernel/git/romieu...
David S. Miller [Sun, 24 Apr 2011 18:51:04 +0000 (11:51 -0700)]
Merge branch 'davem.r8169' of git://git./linux/kernel/git/romieu/netdev-2.6

13 years agonet: Remove __KERNEL__ cpp checks from include/net
David S. Miller [Sun, 24 Apr 2011 17:54:56 +0000 (10:54 -0700)]
net: Remove __KERNEL__ cpp checks from include/net

These header files are never installed to user consumption, so any
__KERNEL__ cpp checks are superfluous.

Projects should also not copy these files into their userland utility
sources and try to use them there.  If they insist on doing so, the
onus is on them to sanitize the headers as needed.

Signed-off-by: David S. Miller <davem@davemloft.net>
13 years agor8169: don't request firmware when there's no userspace.
François Romieu [Sun, 24 Apr 2011 15:38:48 +0000 (17:38 +0200)]
r8169: don't request firmware when there's no userspace.

The firmware is cached during the first successfull call to open() and
released once the network device is unregistered. The driver uses the
cached firmware between open() and unregister_netdev().

So far the firmware is optional : a failure to load the firmware does
not prevent open() to success. It is thus necessary to 1) unregister
all 816x / 810[23] devices and 2) force a driver probe to issue a new
firmware load.

Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Fixed-by: Ciprian Docan <docan@eden.rutgers.edu>
Cc: Realtek linux nic maintainers <nic_swsd@realtek.com>
13 years agobnx2x: fix UDP csum offload
Vladislav Zolotarov [Sat, 23 Apr 2011 07:44:46 +0000 (07:44 +0000)]
bnx2x: fix UDP csum offload

Fixed packets parameters for FW in UDP checksum offload flow.

Do not dereference TCP headers on non TCP frames.
Reported-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
13 years agonetconsole: fix deadlock when removing net driver that netconsole is using (v2)
Neil Horman [Fri, 22 Apr 2011 08:10:59 +0000 (08:10 +0000)]
netconsole: fix deadlock when removing net driver that netconsole is using (v2)

A deadlock was reported to me recently that occured when netconsole was being
used in a virtual guest.  If the virtio_net driver was removed while netconsole
was setup to use an interface that was driven by that driver, the guest
deadlocked.  No backtrace was provided because netconsole was the only console
configured, but it became clear pretty quickly what the problem was.  In
netconsole_netdev_event, if we get an unregister event, we call
__netpoll_cleanup with the target_list_lock held and irqs disabled.
__netpoll_cleanup can, if pending netpoll packets are waiting call
cancel_delayed_work_sync, which is a sleeping path.  the might_sleep call in
that path gets triggered, causing a console warning to be issued.  The
netconsole write handler of course tries to take the target_list_lock again,
which we already hold, causing deadlock.

The fix is pretty striaghtforward.  Simply drop the target_list_lock and
re-enable irqs prior to calling __netpoll_cleanup, the re-acquire the lock, and
restart the loop.  Confirmed by myself to fix the problem reported.

Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
CC: "David S. Miller" <davem@davemloft.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
13 years agoMerge branch 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/linville/wirel...
David S. Miller [Fri, 22 Apr 2011 20:21:38 +0000 (13:21 -0700)]
Merge branch 'master' of git://git./linux/kernel/git/linville/wireless-2.6

13 years agoinet: constify ip headers and in6_addr
Eric Dumazet [Fri, 22 Apr 2011 04:53:02 +0000 (04:53 +0000)]
inet: constify ip headers and in6_addr

Add const qualifiers to structs iphdr, ipv6hdr and in6_addr pointers
where possible, to make code intention more obvious.

Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
13 years agoRevert "bridge: Forward reserved group addresses if !STP"
David S. Miller [Fri, 22 Apr 2011 04:17:25 +0000 (21:17 -0700)]
Revert "bridge: Forward reserved group addresses if !STP"

This reverts commit 1e253c3b8a1aeed51eef6fc366812f219b97de65.

It breaks 802.3ad bonding inside of a bridge.

The commit was meant to support transport bridging, and specifically
virtual machines bridged to an ethernet interface connected to a
switch port wiht 802.1x enabled.

But this isn't the way to do it, it breaks too many other things.

Signed-off-by: David S. Miller <davem@davemloft.net>
13 years agoatl1c: Fix work event interrupt/task races
Tim Gardner [Wed, 20 Apr 2011 09:00:49 +0000 (09:00 +0000)]
atl1c: Fix work event interrupt/task races

The mechanism used to initiate work events from the interrupt
handler has a classic read/modify/write race between the interrupt
handler that sets the condition, and the worker task that reads and
clears the condition. Close these races by using atomic
bit fields.

Cc: stable@kernel.org
Cc: Jie Yang <jie.yang@atheros.com>
Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
13 years agobe2net: increment work_counter in be_worker
Ivan Vecera [Thu, 21 Apr 2011 00:20:04 +0000 (00:20 +0000)]
be2net: increment work_counter in be_worker

The commit 609ff3b ("be2net: add code to display temperature of ASIC")
adds support to display temperature of ASIC but there is missing
increment of work_counter in be_worker. Because of this 1) the
function be_cmd_get_die_temperature is called every 1 second instead
of every 32 seconds 2) be_cmd_get_die_temperature is called, although
it is not supported.  This patch fixes this bug.

Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
13 years agoipv6: Remove hoplimit initialization to -1
Thomas Egerer [Wed, 20 Apr 2011 22:56:02 +0000 (22:56 +0000)]
ipv6: Remove hoplimit initialization to -1

The changes introduced with git-commit a02e4b7d ("ipv6: Demark default
hoplimit as zero.") missed to remove the hoplimit initialization. As a
result, ipv6_get_mtu interprets the return value of dst_metric_raw
(-1) as 255 and answers ping6 with this hoplimit.  This patche removes
the line such that ping6 is answered with the hoplimit value
configured via sysctl.

Signed-off-by: Thomas Egerer <thomas.egerer@secunet.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
13 years agonet: fix hw_features ethtool_ops->set_flags compatibility
Michał Mirosław [Thu, 21 Apr 2011 13:59:21 +0000 (13:59 +0000)]
net: fix hw_features ethtool_ops->set_flags compatibility

__ethtool_set_flags() was not taking into account features set but not
user-toggleable.

Since GFLAGS returns masked dev->features, EINVAL is returned when
passed flags differ to it, and not to wanted_features.

Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
13 years agotg3: Add additional EEE messaging
Matt Carlson [Wed, 20 Apr 2011 07:57:43 +0000 (07:57 +0000)]
tg3: Add additional EEE messaging

This patch adds link messages and an item to the sign-on banner to make
EEE status more visible.

Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
13 years agotg3: Add macro for SMDSP toggling
Matt Carlson [Wed, 20 Apr 2011 07:57:42 +0000 (07:57 +0000)]
tg3: Add macro for SMDSP toggling

A common AUX CTRL operation in the driver is to enable and disable the
SMDSP.  This patch consolidates the code so that the details of the
operation are in one place.  This patch also adds code to make sure the
SMDSP is enabled before executing code that relies on it.

Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
13 years agotg3: Add write accessor for AUX CTRL phy reg
Matt Carlson [Wed, 20 Apr 2011 07:57:41 +0000 (07:57 +0000)]
tg3: Add write accessor for AUX CTRL phy reg

This patch adds a write accessor for the aux ctrl phy register.

Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
13 years agotg3: Add read accessor for AUX CTRL phy reg
Matt Carlson [Wed, 20 Apr 2011 07:57:40 +0000 (07:57 +0000)]
tg3: Add read accessor for AUX CTRL phy reg

This patch adds a read accessor for the aux ctrl register.

Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
13 years agotg3: Move phy accessor functions higher
Matt Carlson [Wed, 20 Apr 2011 07:57:39 +0000 (07:57 +0000)]
tg3: Move phy accessor functions higher

Phy accessor functions should live closer to where the base phy read /
write routines are.

Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
13 years agotg3: Only allow phy ioctls while netif_running
Matt Carlson [Wed, 20 Apr 2011 07:57:38 +0000 (07:57 +0000)]
tg3: Only allow phy ioctls while netif_running

When tg3 was new, phy accesses through ioctl were allowable at any time.
Then, the driver started shutting down the phy when the device was
closed.  Phy accesses would be allowed when the driver first attached to
the device, but then would be forbidden after the device had been up'd
and down'd.  After that, management firmware made it illegal to access
the phy unless the driver "owned" the device.  Now that most firmware
is being moved over to the APE, it is less clear when phy accesses are
safe.

While it is possible to attempt to identify these conditions and code
the driver to navigate through the pitfalls, it could be perplexing to
the admin why phy accesses work in some cases and not others.  This
patch brings some uniformity to the problem by only allowing phy
accesses while the driver has control of the device.

Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
13 years agotg3: Nullify RSS for loopback test
Matt Carlson [Wed, 20 Apr 2011 07:57:37 +0000 (07:57 +0000)]
tg3: Nullify RSS for loopback test

The loopback test assumes all traffic goes to the first rx queue.  There
is a 1 in 4 chance this won't be true if RSS is enabled though.  This
patch reprograms the RSS indirection table to route all rx packets to
the first queue.

Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
13 years agotg3: Adjust rx prod ring bd replenish thresholds
Matt Carlson [Wed, 20 Apr 2011 07:57:36 +0000 (07:57 +0000)]
tg3: Adjust rx prod ring bd replenish thresholds

The oldest tg3 devices had large rx producer ring BD caches.  Back then,
it made sense to make the BD cache replenish threshold only a function
of the number of rx buffers posted by the driver.  Since then, the BD
cache sizes have shrunk to 25% of their original size and, in some
cases, the ring sizes have quadrupled in size.  Under such conditions,
static BD cache replenish thresholds no longer match the hardware
constraints.

This patch attempts to factor in the BD cache size into the bd cache
replenish strategy, taking the existing hardware bugs into account.

Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>