net/mlx4_en: Add HW timestamping (TS) support

The patch allows to enable/disable HW timestamping for incoming and/or
outgoing packets. It adds and initializes all structs and callbacks
needed by kernel TS API.
To enable/disable HW timestamping appropriate ioctl should be used.
Currently HWTSTAMP_FILTER_ALL/NONE and HWTSAMP_TX_ON/OFF only are
supported.
When enabling TS on receive flow - VLAN stripping will be disabled.
Also were made all relevant changes in RX/TX flows to consider TS request
and plant HW timestamps into relevant structures.
mlx4_ib was fixed to compile with new mlx4_cq_alloc() signature.

Signed-off-by: Eugenia Emantayev <eugenia@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net/mlx4_core: Read HCA frequency and map internal clock

Read HCA frequency, read PCI clock bar and offset, map internal clock to
PCI bar.

Signed-off-by: Eugenia Emantayev <eugenia@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net/mlx4_core: Add timestamping device capability

Add new device capability for timestamping support and query FW to retrieve it.

Signed-off-by: Eugenia Emantayev <eugenia@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge branch 'for-davem' of git://git./linux/kernel/git/linville/wireless-next

John W. Linville says:

====================
Here is one last(?) big wireless bits pull request before the merge window...

Regarding the mac80211 bits, Johannes says:

"Here's another big pull request for the -next stream. This one has a ton
of driver updates, which hopefully addresses all drivers, but maybe you
have more new drivers than I have in my tree? Not entirely sure, let me
know if this is the case and then I can merge wireless-next.

I'm including a large number of small changes, see the shortlog. The two
bigger things are making VHT compatible with not using channel contexts
(from Karl) and the stop-while-suspended fixes I developed together with
Stanislaw."

...and...

"This time I have a relatively large number of fixes and small
improvements, the most important one being Bob's RCU fix. The two big
things are Felix's work on rate scaling tables (with a big thanks to
Karl too) and my own work on CSA handling to finally properly handle HT
(and some VHT.)"

As for the iwlwifi bits, Johannes says:

"The biggest work here is Bluetooth coexistence and power saving. Other
than that, I have a few small fixes that weren't really needed for 3.9
and a new PCI ID."

About the NFC bits, Samuel says:

"With this one we have:

- A major pn533 update. The pn533 framing support has been changed in order to
  easily support all pn533 derivatives. For example we now support the ACR122
  USB dongle.

- An NFC MEI physical layer code factorization through the mei_phy NFC API.
  Both the microread and the pn544 drivers now use it.

- LLCP aggregation support. This allows NFC p2p devices to send aggregated
  frames containing all sort of LLCP frames except SYMM and aggregation
  frames.

- More LLCP socket options for getting the remote device link parameters.

- Fixes for the LLCP socket option code added with the first pull request for
  3.10.

- Some support for LLCP corner cases like 0 length SDUs and general DISC
  (tagged with a 0,0 dsap ssap couple) handling.

- RFKILL support for NFC."

For the b43 bits, Rafał says:

"Let me remind the changes for b43:
> Changes include:
> 1) Minor improvements for HT-PHY code (BCM4331)
> 2) Code cleaning for HT-PHY and N-PHY"

Concerning the bluetooth bits, Gustavo says:

"A set of changes intended for 3.10. The biggest changes here are from David
Herrmann, he rewrote most of the HIDP layer making it more reliable. Marcel
added a driver setup stage for device that need special handling on their
early initialization. Other than that we have the usual clean ups, bugfixes
and small improvements."

Along with all that, there is the usual collection of random/various
updates to ath9k, mwifiex, brcmfmac, brcmsmac, rt2x00, and wil6210.

I also included a pull of the wireless tree to resolve a merge conflict.

Please let me know if there are problems!
====================

Signed-off-by: David S. Miller <davem@davemloft.net>

netlink: fix compilation after memory mapped patches

Depending of the kernel configuration (CONFIG_UIDGID_STRICT_TYPE_CHECKS), we can
get the following errors:

net/netlink/af_netlink.c: In function ‘netlink_queue_mmaped_skb’:
net/netlink/af_netlink.c:663:14: error: incompatible types when assigning to type ‘__u32’ from type ‘kuid_t’
net/netlink/af_netlink.c:664:14: error: incompatible types when assigning to type ‘__u32’ from type ‘kgid_t’
net/netlink/af_netlink.c: In function ‘netlink_ring_set_copied’:
net/netlink/af_netlink.c:693:14: error: incompatible types when assigning to type ‘__u32’ from type ‘kuid_t’
net/netlink/af_netlink.c:694:14: error: incompatible types when assigning to type ‘__u32’ from type ‘kgid_t’

We must use the helpers to get the uid and gid, and also take care of user_ns.

Fix suggested by Eric W. Biederman <ebiederm@xmission.com>.

Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge branch 'master' of git://git./linux/kernel/git/linville/wireless-next into for-davem

netlink: Fix build with mmap disabled.

net/netlink/diag.c: In function 'sk_diag_put_rings_cfg':
net/netlink/diag.c:28:17: error: 'struct netlink_sock' has no member named 'pg_vec_lock'
net/netlink/diag.c:29:29: error: 'struct netlink_sock' has no member named 'rx_ring'
net/netlink/diag.c:31:30: error: 'struct netlink_sock' has no member named 'tx_ring'
net/netlink/diag.c:33:19: error: 'struct netlink_sock' has no member named 'pg_vec_lock'

Reported-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

mwifiex: rework round robin scheduling of bss nodes.

Rotate bss prio list, so the bss next to the one served, will come first
in the list of bss' with equal priority. This way we pick bss nodes in a
round robin fashion. Using list rotation instead of a cur ptr simplifies
iteration to calling list_for_each_entry. List rotation is done via
list_move, where the head itself is temporarily removed and then
re-inserted after the bss just served.

Signed-off-by: Andreas Fenkart <andreas.fenkart@streamunlimited.com>
Acked-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mwifiex: replace ra_list_curr by list rotation.

After a packet is successfully transmitted, ra list is rotated, so the ra
next to the one transmitted, will be the first in the list. This way we
pick the ra' in a round robin fashion. This significantly simplifies
iteration in  mwifiex_wmm_get_highest_priolist_ptr to a call to
list_for_each_entry.
List rotation is done via list_move, where the head itself is temporarily
removed and then re-inserted after the item just transferred.

Signed-off-by: Andreas Fenkart <andreas.fenkart@streamunlimited.com>
Acked-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcmfmac: add credit borrowing mechanism

The firmware provides credits to the driver per WMM-AC. When
only AC_BE are to be transmitted to the firmware the driver
may use credits from other priorities to send AC_BE packets
towards the firmware.

Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcmfmac: correct error handling in brcmf_fws_init()

In brcmf_fws_init() the error flows were not properly handled
and the caller ignored the return value. The only action that
is allowed to fail in brcmf_fws_init() is setting the tlv in
firmware as the feature is not supported on all devices.

Cc: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcmfmac: flush queue upon MACDESC_DEL firmware signal

When firmware signals the driver to remove a destination entry
it may have sk_buff packets queued for it. These should be freed.

Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcmfmac: support critical protocol API for DHCP

Adds support for the critical protocol API provided by nl80211
which gives Wifi traffic priority over a Bluetooth (e)SCO connection
and disables scanning during DCHP negotiation.

Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Piotr Haber <phaber@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcmfmac: allow scanning to be suppressed in the driver

During the DHCP protocol exchange it is benificial to suppress
scan requests which may decrease time to complete DHCP protocol.

Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: Fix RX DMA mapping

After the commit "ath9k: improve dma map failure handling", the
wrong buffer was DMA-unmapped, introducing warnings like the one below.
This patch fixes the issue.

WARNING: at /home/sujith/dev/wireless-testing/lib/dma-debug.c:986 check_sync+0x4bc/0x580()
Hardware name: LIFEBOOK AH531
ath9k 0000:02:00.0: DMA-API: device driver tries to sync DMA memory it has not allocated [device address=0x00000000d9012800] [size=48 bytes]
Pid: 86, comm: kworker/u:5 Tainted: G        W  O 3.9.0-rc8-wl-debug #106
Call Trace:
 [<ffffffff810410c0>] warn_slowpath_common+0x70/0xa0
 [<ffffffff8104113c>] warn_slowpath_fmt+0x4c/0x50
 [<ffffffff8125432c>] check_sync+0x4bc/0x580
 [<ffffffff8109e5f7>] ? trace_hardirqs_on_caller+0xa7/0x190
 [<ffffffff8109e6ed>] ? trace_hardirqs_on+0xd/0x10
 [<ffffffff81254488>] debug_dma_sync_single_for_device+0x48/0x50
 [<ffffffffa0a53825>] ? ath9k_iowrite32+0x35/0x90 [ath9k]
 [<ffffffff812512f0>] ? swiotlb_tbl_sync_single+0x50/0x90
 [<ffffffff81251350>] ? swiotlb_sync_single+0x20/0x30
 [<ffffffff8125137f>] ? swiotlb_sync_single_for_device+0xf/0x20
 [<ffffffffa0a58baf>] ath_rx_edma_buf_link+0xef/0x140 [ath9k]
 [<ffffffffa0a58c4e>] ath_rx_addbuffer_edma+0x4e/0x90 [ath9k]
 [<ffffffffa0a59c51>] ath_startrecv+0xf1/0x120 [ath9k]
 [<ffffffffa0a550e0>] ath_complete_reset+0x20/0x130 [ath9k]
 [<ffffffffa0a5790d>] ath_reset_internal+0x10d/0x210 [ath9k]
 [<ffffffffa0a5878c>] ath9k_config+0x47c/0x7b0 [ath9k]
 [<ffffffffa06d4978>] ieee80211_hw_config+0x88/0x3f0 [mac80211]
 [<ffffffffa06d4a3f>] ? ieee80211_hw_config+0x14f/0x3f0 [mac80211]
 [<ffffffffa06dbed1>] __ieee80211_scan_completed+0xc1/0x440 [mac80211]
 [<ffffffffa06dd002>] ieee80211_scan_work+0x82/0x440 [mac80211]
 [<ffffffff810606a3>] process_one_work+0x1e3/0x530
 [<ffffffff81060641>] ? process_one_work+0x181/0x530
 [<ffffffff8106163f>] worker_thread+0x10f/0x3c0
 [<ffffffff81061530>] ? manage_workers+0x330/0x330
 [<ffffffff810665da>] kthread+0xea/0xf0
 [<ffffffff810664f0>] ? kthread_create_on_node+0x140/0x140
 [<ffffffff8146085c>] ret_from_fork+0x7c/0xb0
 [<ffffffff810664f0>] ? kthread_create_on_node+0x140/0x140

Cc: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Acked-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: Use lockless variants for the RX fifo queue

The RX fifo can be accessed from the common tasklet or it can
be reaped/cleaned when RX is stopped, which is done when doing
a reset or channel change - this happens in process context.

Since it is ensured that there are no pending tasklets when
stopping RX and cleaning the FIFO, there is no need to use
SKB queue functions which take internal locks.

Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Acked-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: Reduce deep indentation

The EDMA case is handled first, so the else condition
can be removed.

Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Acked-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: Remove unused argument "size"

Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Acked-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: add support for the new rate control API

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: merge ath_tx_start_dma into ath_tx_start

The split makes no sense and merging the functions makes further changes
easier to implement

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rtl8192c:dm: Properly initialize local array and set value.

GCC 4.8 is spitting out uninitialized-variable warnings against
"drivers/net/wireless/rtlwifi/rtl8192c/dm_common.c".  This patch adds
initialization to the variable and properly sets its value.

Signed-off-by: Han Shen (shenhan@google.com)
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: apply coverage class on slottime too

According to 802.11-2007 17.3.8.6 (slot time), the slot time should
be increased by 3 us * coverage class. The code only increased the
ack timeout, which is fixed by this patch.

We have noticed in our long shot scenario that we see less collisions
with this patch.

Signed-off-by: Mathias Kretschmer <mathias.kretschmer@fokus.fraunhofer.de>
[add standard reference and commit message]
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Merge branch 'master' of git://git.infradead.org/users/rafal/b43-next

Merge branch 'master' of git://git./linux/kernel/git/linville/wireless

Conflicts:
drivers/net/wireless/brcm80211/brcmsmac/mac80211_if.c

caif: Update Dmitry's email address.

Dmitry's address will start bouncing in a few days,
update to his new mail address.

Cc: Dmitry Tarnyagin <dmitry.tarnyagin@stericsson.com>
Cc: Dmitry Tarnyagin <dmitry.tarnyagin@lockless.no>
Signed-off-by: Sjur Brændeland <sjur.brandeland@stericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

caif: Remove bouncing address for Daniel Martensson

cc: Daniel Martensson <Daniel.Martensson@stericsson.com>
Signed-off-by: Sjur Brændeland <sjur.brandeland@stericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

caif: Remove my bouncing email address.

Remove my soon bouncing email address.
Also remove the "Contact:" line in file header.
The MAINTAINERS file is a better place to find the
contact person anyway.

Signed-off-by: Sjur Brændeland <sjur.brandeland@stericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

MAINTAINERS: Change Maintainer for CAIF

Dmitry Tarnyagin will take over as maintainer for CAIF.

Cc: Dmitry Tarnyagin <dmitry.tarnyagin@stericsson.com>
Cc: Dmitry Tarnyagin <dmitry.tarnyagin@lockless.no>
Signed-off-by: Sjur Brændeland <sjur.brandeland@stericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

netlink: fix typo in net/netlink/af_netlink.c

Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>

b43: N-PHY: don't use deprecated b43_radio_foo16

All radio ops are 16b (there is only 1 exception for reg 0x1), so we
deprecated b43_radio_read16 and b43_radio_write16 long time ago.

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>

b43: N-PHY: clean init tables

Sort defines, use one macro for all revs, support for 5GHz when
uploading antenna table.

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>

b43: N-PHY: move tables init function to tables file

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>

b43: N-PHY: use defines for (re)storing VCM config

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>

b43: N-PHY: use shortcut "ctl" in functions names

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>

b43: N-PHY: use enum for INTC override function argument

Also make a function name shorter so we can easily fit 80 chars.

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>

b43: N-PHY: define missing registers

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>

b43: use defines for board_type

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>

b43: N-PHY: fix "NB" RSSI calibration on PHYs rev2-

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>

b43: N-PHY: use enum for RSSI type everywhere we use it

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>

b43: N-PHY: rename RSSI types to be shorter and more accurate

Thanks to Broadcom releasing some code we can use better names.

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>

b43: N-PHY: use more friendly variables names in RSSI code

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>

b43: N-PHY: simplify conditions in RSSI offset scale function

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>

b43: N-PHY: use enum for RAIL type

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>

b43: HT-PHY: use enum for RSSI types

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>

b43: HT-PHY: store TX power state before disabling it

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>

b43: HT-PHY: define regs for power estimation

In MMIO dumps of ndiswrapper there are following PHY ops:
phy_read(0x0118) -> 0x013d
phy_read(0x01ed) -> 0x993d
phy_read(0x0119) -> 0x012f
phy_read(0x01ee) -> 0x992f
phy_read(0x011a) -> 0x0139
phy_read(0x0969) -> 0x9939
It matches the code of wlc_phy_txpower_est_power_nphy (from brcm80211),
so we know the registers meaning.

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>

b43: HT-PHY: do some extra TSSI setup after configuring TX

After b43_phy_ht_tx_power_ctl_setup there are some extra radio ops:
 radio_read(0x08bf) -> 0x0001
radio_write(0x08bf) <- 0x0001
radio_write(0x0159) <- 0x0011
On N-PHY we write 0x11 to TSSI regs, so it's probably sth similar.

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>

b43: HT-PHY: finish calculating values for idle TSSI

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>

b43: HT-PHY: tables: don't duplicate core-generic regs

Now when we know many radio regs at 0x000 are core-generic, I've noticed
we duplicate some values in the tables.

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>

b43: HT-PHY: rename defines addressing cores on the 2059 radio

After comparing writes to registers at 0x000, 0x400 and 0x800 it seems
there are many very similar writes. So 0x000 offset is not for accessing
something totally different, but probably just the first out of three
cores.

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>

batman-adv: fix global protection fault during soft_iface destruction

batadv_mesh_free() schedules some RCU callbacks which need the bat_priv struct
to do their jobs, while free_netdev(), which is called immediately after, is
destroying the private data.

Put an rcu_barrier() in the middle so that free_netdev() is invoked only after
all the callbacks returned.

This bug has been introduced by ab8f433dd39be94e8617cff2dfe9f7eca162eb15
("batman-adv: Move deinitialization of soft-interface to destructor")

Signed-off-by: Antonio Quartulli <ordex@autistici.org>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge git://git./linux/kernel/git/davem/net

Conflicts:
drivers/net/ethernet/emulex/benet/be_main.c
drivers/net/ethernet/intel/igb/igb_main.c
drivers/net/wireless/brcm80211/brcmsmac/mac80211_if.c
include/net/scm.h
net/batman-adv/routing.c
net/ipv4/tcp_input.c

The e{uid,gid} --> {uid,gid} credentials fix conflicted with the
cleanup in net-next to now pass cred structs around.

The be2net driver had a bug fix in 'net' that overlapped with the VLAN
interface changes by Patrick McHardy in net-next.

An IGB conflict existed because in 'net' the build_skb() support was
reverted, and in 'net-next' there was a comment style fix within that
code.

Several batman-adv conflicts were resolved by making sure that all
calls to batadv_is_my_mac() are changed to have a new bat_priv first
argument.

Eric Dumazet's TS ECR fix in TCP in 'net' conflicted with the F-RTO
rewrite in 'net-next', mostly overlapping changes.

Thanks to Stephen Rothwell and Antonio Quartulli for help with several
of these merge resolutions.

Signed-off-by: David S. Miller <davem@davemloft.net>

net: Fix vlan bitmask changes in EHEA driver.

This driver uses the crummy "| foo" style, putting the
logical operation at the beginning of lines.  Then
when the VLAN tag flag bits got changed the operator
ended up at both the end and the beginning of some lines.

Fix the build error by having it uniformly use the operator
at the end of the line.

Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: Fix some __vlan_hwaccel_put_tag() callers.

Several call sites were missed when the protocol argument was added to
__vlan_hwaccel_put_tag() in commit
86a9bad3ab6b6f858fd4443b48738cabbb6d094c ("net: vlan: add protocol
argument to packet tagging functions").

Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: sctp: minor: remove dead code from sctp_packet

struct sctp_packet is currently embedded into sctp_transport or
sits on the stack as 'singleton' in sctp_outq_flush(). Therefore,
its member 'malloced' is always 0, thus a kfree() is never called.
Because of that, we can just remove this code.

Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

VXLAN: Allow L2 redirection with L3 switching

Allow L2 redirection when VXLAN L3 switching is enabled

This patch restricts L3 switching to destination MAC addresses that are
marked as routers in order to allow virtual IP appliances that do L2
redirection to function with VXLAN L3 switching enabled.

We use L3 switching on VXLAN networks to avoid extra hops when the nominal
router for cross-subnet traffic for a VM is remote and the ultimate
destination may be local, or closer to the local node. Currently, the
destination IP address takes precedence over the MAC address in all cases.
Some network appliances receive packets for a virtualized IP address and
redirect by changing the destination MAC address (only) to be the final
destination for packet processing. VXLAN tunnel endpoints with L3 switching
enabled may then overwrite this destination MAC address based on the packet IP
address, resulting in potential loops and, at least, breaking L2 redirections
that travel through tunnel endpoints.

This patch limits L3 switching to the intended case where the original
destination MAC address is a next-hop router and relies on the destination
MAC address for all other cases, thus allowing L2 redirection and L3 switching
to coexist peacefully.

Signed-Off-By: David L Stevens <dlstevens@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: Remove return value from list_netdevice()

The return value from list_netdevice() is not used and no need, so remove it.

Signed-off-by: Ding Tianhong <dingtianhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: remove a stale comment for dl_next

dl_next member in struct request_sock doesn't need to be first.

We expect to insert a "struct common_sock" or a subset of it,
so this claim had to be verified.

Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

qeth: Fix missing pointer update

qeth_hdr_chk_and_bounce() can possibly shift the skb->data
pointer. However, the existing code didn't update the hdr pointer,
which should point to skb->data, accordingly.
Symptoms of this issue are sporadic recoveries.

Signed-off-by: Stefan Raspl <raspl@linux.vnet.ibm.com>
Signed-off-by: Frank Blaschka <blaschka@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

qeth: remove unused variable

remove unused variable

Signed-off-by: Stefan Raspl <raspl@linux.vnet.ibm.com>
Signed-off-by: Frank Blaschka <blaschka@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

qeth: remove cast for kzalloc return value

remove cast for kzalloc return value.

Signed-off-by: Zhang Yanfei <zhangyanfei@cn.fujitsu.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Frank Blaschka <blaschka@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

mwifiex: remove redundant initialization for bss_descriptor

Initialization of bss_descriptor is unnecessary as the entire
structure will be overwritten by a memcpy followed by.

Initialize disable_11ac flag properly by setting it to true in
mwifiex_fill_new_bss_desc().

Reported-by: Doug Anderson <dianders@chromium.org>
Reviewed-by: Doug Anderson <dianders@chromium.org>
Reviewed-by: Paul Stewart <pstew@chromium.org>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: Yogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mwifiex: fix use-after-free in beacon_ie processing

beacon_ie buffer is allocated in mwifiex_fill_new_bss_desc()
and the buffer pointer is saved in bss_desc->beacon_buf.
beacon_ie is freed before the function returns. However,
bss_desc->beacon_buf is still being accessed afterwards.

Fix it by freeing beacon_ie (bss_desc->beacon_buf) in
caller's scope.

Reviewed-by: Doug Anderson <dianders@chromium.org>
Reviewed-by: Paul Stewart <pstew@chromium.org>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

xen-netback: don't disconnect frontend when seeing oversize packet

Some frontend drivers are sending packets > 64 KiB in length. This length
overflows the length field in the first slot making the following slots have
an invalid length.

Turn this error back into a non-fatal error by dropping the packet. To avoid
having the following slots having fatal errors, consume all slots in the
packet.

This does not reopen the security hole in XSA-39 as if the packet as an
invalid number of slots it will still hit fatal error case.

Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Signed-off-by: Wei Liu <wei.liu2@citrix.com>
Acked-by: Ian Campbell <ian.campbell@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

xen-netback: coalesce slots in TX path and fix regressions

This patch tries to coalesce tx requests when constructing grant copy
structures. It enables netback to deal with situation when frontend's
MAX_SKB_FRAGS is larger than backend's MAX_SKB_FRAGS.

With the help of coalescing, this patch tries to address two regressions
avoid reopening the security hole in XSA-39.

Regression 1. The reduction of the number of supported ring entries (slots)
per packet (from 18 to 17). This regression has been around for some time but
remains unnoticed until XSA-39 security fix. This is fixed by coalescing
slots.

Regression 2. The XSA-39 security fix turning "too many frags" errors from
just dropping the packet to a fatal error and disabling the VIF. This is fixed
by coalescing slots (handling 18 slots when backend's MAX_SKB_FRAGS is 17)
which rules out false positive (using 18 slots is legit) and dropping packets
using 19 to `max_skb_slots` slots.

To avoid reopening security hole in XSA-39, frontend sending packet using more
than max_skb_slots is considered malicious.

The behavior of netback for packet is thus:

    1-18            slots: valid
   19-max_skb_slots slots: drop and respond with an error
   max_skb_slots+   slots: fatal error

max_skb_slots is configurable by admin, default value is 20.

Also change variable name from "frags" to "slots" in netbk_count_requests.

Please note that RX path still has dependency on MAX_SKB_FRAGS. This will be
fixed with separate patch.

Signed-off-by: Wei Liu <wei.liu2@citrix.com>
Acked-by: Ian Campbell <ian.campbell@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

xen-netfront: reduce gso_max_size to account for max TCP header

The maximum packet including header that can be handled by netfront / netback
wire format is 65535. Reduce gso_max_size accordingly.

Drop skb and print warning when skb->len > 65535. This can 1) save the effort
to send malformed packet to netback, 2) help spotting misconfiguration of
netfront in the future.

Signed-off-by: Wei Liu <wei.liu2@citrix.com>
Acked-by: Ian Campbell <ian.campbell@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

xen-netfront: frags -> slots in log message

Also fix a typo in comment.

Signed-off-by: Wei Liu <wei.liu2@citrix.com>
Acked-by: Ian Campbell <ian.campbell@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

be2net: enable IOMMU pass through for be2net

This patch sets the coherent DMA mask to 64-bit after the be2net driver has
been acknowledged that the system is 64-bit DMA capable. The coherent DMA
mask is examined by the Intel IOMMU driver to determine whether to allow
pass through context mapping for all devices. With this patch, the be2net
driver combined with be2net compatible hardware provides comparable
performance to the case where vt-d is disabled. The main use-case for this
change is to decrease the time necessary to copy virtual machine memory
during KVM live migration instantiations.

This patch was tested on a system that enables the IOMMU in non-coherent
mode. Two DMA remapper issues were encountered in the previous version and
both patches have been committed.
    commit ea2447f700cab264019b52e2b417d689e052dcfd
    commit 2e12bc29fc5a12242d68e11875db3dd58efad9ff

Signed-off-by: Craig Hada <craig.hada@hp.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

be2net: Use GET_PROFILE_CONFIG V1 cmd for BE3-R

Use GET_PROFILE_CONFIG_V1 cmd for BE3-R, to query the maximum number of
TX rings available per function. On SH-R the same is queried via the
GET_FUNCTION_CONFIG cmd.

Signed-off-by: Vasundhara Volam <vasundhara.volam@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

be2net: Avoid flashing BE3 UFI on BE3-R chip.

Avoid flashing BE3 UFI on BE3-R chip by verifying asic_revision
number of the chip.

Signed-off-by: Vasundhara Volam <vasundhara.volam@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

be2net: Don't log "Out of MCCQ wrbs" error

Don't log "Out of MCCQ wrbs" msg. When the driver doesn't receive any
response from the FW it already logs a "FW not responding" message.
The driver runs out of MCCQ wrbs much later. Also, this message can
swamp the kernel log in HW/FW error scenarios.

Signed-off-by: Vasundhara Volam <vasundhara.volam@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

be2net: Use TXQ_CREATE_V2 cmd

Skyhawk-R and BE3-R (SuperNIC profile) require V2 version
of TXQ_CREATE cmd to be used.

Signed-off-by: Vasundhara Volam <vasundhara.volam@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bnx2x: update version to 1.78.17-0

Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bnx2x: allow nvram test to run when device is down

Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bnx2x: add additional regions for CRC memory test

a. Common tree of `dir` structures.
b. Multi-port devices structures.

CC: Francious Romieu <romieu@fz.zoreil.com>
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bnx2x: remove non-necessary assignment

CC: Francious Romieu <romieu@fz.zoreil.com>
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bnx2x: fix byte-by-byte nvram write for BE machines

CC: Francious Romieu <romieu@fz.zoreil.com>
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bnx2x: refactor nvram read procedure

introduce a procedure to read in u32 granularity.

CC: Francious Romieu <romieu@fz.zoreil.com>
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

mwifiex: don't try to associate when bss_mode is not STA

We have blocked association attempts on interfaces configured in
AP and AD-HOC modes. P2P mode should be blocked too.

Furthermore, an error code must be returned if we are unable to
associate.

Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mwifiex: make use of msecs_to_jiffies()

Use msecs_to_jiffies() wherever possible.

Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: Yogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mwifiex: correct bss_mode check while appending vht operation IE

priv->bss_mode uses NL80211_IFTYPE_* definitions.
HostCmd_BSS_MODE_IBSS is used in ad-hoc start/join command between
driver and firmware.

Coincidentally both HostCmd_BSS_MODE_IBSS and NL80211_IFTYPE_STATION
are defined as 2. That explains why nobody complained.

Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mwifiex: use PCI_DMA_FROMDEVICE for RX queue de-init

There is a typo in mwifiex_cleanup_rxq_ring() which uses
PCI_DMA_TODEVICE while unmapping PCI memory.
We should actually use PCI_DMA_FROMDEVICE.

Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Yogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mwifiex: configure p2p interface during initialization

Send P2P_MODE_CFG cmd to firmware when p2p interface is created.
Without proper p2p configuration firmware may behave incorrectly
while handling commands sent through this interface.

Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: Stone Piao <piaoyun@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mwifiex: Start P2P devices in P2P mode

p2p devices should identify themselves as such to userspace at
startup, so the connection manager can decide which interface
to start wpa_supplicant instances on.

Signed-off-by: Paul Stewart <pstew@chromium.org>
Reviewed-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rt2x00: Use more current logging styles, shrink object size

Reduce object space ~2% using more current logging styles.

Neaten and simplify logging macros.
Use wiphy_<level> where appropriate.
Coalesce formats.

Convert ERROR/WARNING/INFO macros to rt2x00_<level>
Convert EEPROM to rt2x00_eeprom_dbg
Convert PROBE_ERROR to rt2x00_probe_err
Convert DEBUG to rt2x00_dbg
Convert EEPROM to rt2x00_eeprom_dbg

$ size drivers/net/wireless/rt2x00/built-in.o*
   text    data     bss     dec     hex filename
 245639   71696   69584  386919   5e767 drivers/net/wireless/rt2x00/built-in.o.new
 240609   70096   68944  379649   5cb01 drivers/net/wireless/rt2x00/built-in.o.new.nodyndbg
 240609   70096   68944  379649   5cb01 drivers/net/wireless/rt2x00/built-in.o.new.no_rt2x00_debug
 249198   70096   70352  389646   5f20e drivers/net/wireless/rt2x00/built-in.o.old
 249198   70096   70352  389646   5f20e drivers/net/wireless/rt2x00/built-in.o.old.nodyndbg
 244222   70096   69712  384030   5dc1e drivers/net/wireless/rt2x00/built-in.o.old.no_rt2x00_debug

Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rt2x00: rt2800lib: rename rt2800_init_bbb_early to rt2800_init_bbp_early

The function is used for BBP register initialization,
fix the typo in the function name to reflect that.

The patch contains no functional changes.

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcmfmac: fix potential NULL pointer dereference in brcmf_fws_flow_control_check()

The dereference to 'ifp' in debug code should be moved below the NULL test.

Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Acked-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

wil6210: more Rx descriptor accessor functions

Helpers to fetch various fields from the Rx descriptor

Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

wil6210: Use cached copy of Tx descriptor

Original Tx descriptor stored is in non-cached area for DMA;
copy it to the cached memory to speed-up access

Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

wil6210: Tx init optimization

vring size is known from the beginning, fill it immediately
in the struct initializer
This is minor optimization that reduces code size.

Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

wil6210: Use cached copy of Rx descriptor

Rx descriptors stored in non-cacheable memory area for DMA.
Non-cacheable memory causes long access time from CPU.

Copy rx descriptor to the skb->cb, and use this copy.
It provides faster memory access, and will be usefull to keep
Rx information for later processing (BACK reorder)

Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcmfmac: stop dequeue upon sk_buff commit failure

In the dequeue worker the function brcmf_commit_skb() is called.
However, instead of increment the credit count upon success it
should break the for loop upon failure. Otherwise, it will result
in an endless loop.

Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcmfmac: change return type for brcmf_rollback_toq() to void

The function brcmf_rollback_toq() is already called in error path
and its result should not override the initial error value. As the
function releases the sk_buff there is no need to return anything
so change return type to void.

Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcmfmac: finalize transmit upon any rollback failure

All rollback failures should result in freeing of the sk_buff
by calling brcmf_txfinalize().

Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcmfmac: use lock in brcmf_fws_del_interface()

When deleting an interface in firmware-signalling module it will
clear any destination descriptors. To avoid concurrency issues it
should take the lock using brcmf_fws_lock().

Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcmfmac: schedule dequeue upon firmware-signal reception

Several firmware signals should be considered as opportunity to
send packets to the firmware. This patch adds conditional scheduling
of the dequeue worker thread while handling those signals.

Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcmfmac: destination mac closed when interface is closed

Firmware signals a destination is closed as well as an interface. A
destination is associated with an interface. When an interface is
closed consequently the destination should be considered closed as
well.

Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcmutil: simplify brcmu_pkt_free_skb()

The function brcmu_pkt_free_skb() use skb->destructor to decide
how the sk_buff should be freed. However, when running AP mode
with iptables configured this results in a kernel warning.

Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Piotr Haber <phaber@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcmfmac: remove error message upon allocation failure

In function brcmf_add_if() an error message is printed
upon alloc_netdev() failure. The allocation failure itself
spews enough info in the log so remove the error message.

Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Piotr Haber <phaber@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcmfmac: check memory allocation in brcmf_add_if()

For P2P_DEVICE interface the struct brcmf_if instance is
allocated using kzalloc() which can fail. Add pointer
check and return -ENOMEM if it failed. Fixes the following
smatch error:

"drivers/net/wireless/brcm80211/brcmfmac/dhd_linux.c:770
brcmf_add_if()
  error: potential null dereference 'ifp'. (kzalloc returns null)"

Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Piotr Haber <phaber@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>