Andrei Emeltchenko [Thu, 25 Oct 2012 12:20:51 +0000 (15:20 +0300)]
Bluetooth: Add put(hcon) when deleting hchan
When refcnt reaches zero disconnect timeout will run and hci_conn
will be disconnected.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Andrei Emeltchenko [Thu, 25 Oct 2012 12:20:45 +0000 (15:20 +0300)]
Bluetooth: AMP: Process Logical Link complete evt
After receiving HCI Logical Link Complete event finish EFS
configuration by sending L2CAP Conf Response with success code.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Andrei Emeltchenko [Thu, 25 Oct 2012 12:20:44 +0000 (15:20 +0300)]
Bluetooth: AMP: Process Physical Link Complete evt
Add processing for HCI Physical Link Complete event. Upon
successful status received start L2CAP create channel process.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Andrei Emeltchenko [Thu, 25 Oct 2012 12:20:43 +0000 (15:20 +0300)]
Bluetooth: Use helper function sending EFS conf rsp
There is helper function used to send EFS Configuration Response.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Andrei Emeltchenko [Thu, 25 Oct 2012 12:20:42 +0000 (15:20 +0300)]
Bluetooth: trivial: Remove unneeded assignment
Assignment is not needed here since err is always gets value.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Johan Hedberg [Wed, 24 Oct 2012 21:09:53 +0000 (00:09 +0300)]
Bluetooth: Fix sending unnecessary HCI_LE_Host_Enable
This patch fixes sending an unnecessary HCI_LE_Host_Enable command if
the command has already been sent as part of the default HCI init
sequence.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Johan Hedberg [Wed, 24 Oct 2012 21:09:54 +0000 (00:09 +0300)]
Bluetooth: Fix unnecessary EIR update during powering on
When powered on the EIR data gets updated as the last step by mgmt.
Therefore avoid an update when getting a local name update as that's
part of the normal HCI init sequence.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Johan Hedberg [Wed, 24 Oct 2012 21:09:52 +0000 (00:09 +0300)]
Bluetooth: Fix sending unnecessary HCI_Write_SSP_Mode command
This patch fixes sending an unnecessary HCI_Write_SSP_Mode command if
the command has already been sent as part of the default HCI init
sequence.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Johan Hedberg [Wed, 24 Oct 2012 21:09:51 +0000 (00:09 +0300)]
Bluetooth: Fix setting host feature bits for SSP
When we get a successful command complete for HCI_Write_SSP_Mode we need
to update the host feature bits for the hdev struct accordingly.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Johan Hedberg [Wed, 24 Oct 2012 18:12:03 +0000 (21:12 +0300)]
Bluetooth: Disallow LE scanning and connecting in peripheral role
When an adapter is in the LE peripheral role scanning for other devices
or initiating connections to them is not allowed. This patch makes sure
that such attempts will result in appropriate error returns.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Johan Hedberg [Wed, 24 Oct 2012 18:12:02 +0000 (21:12 +0300)]
Bluetooth: Add flag for LE GAP Peripheral role
This patch adds a flag to be used for LE GAP Peripheral role. In this
role undirected advertising will be enabled and operations not allowed
in Peripheral role (such as scanning and initiating connections) will be
disallowed.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Johan Hedberg [Wed, 24 Oct 2012 18:12:01 +0000 (21:12 +0300)]
Bluetooth: Make use feature test macros
For better code readability and avoiding simple bugs of checking the
wrong byte of the features make use of feature test macros whenever
possible.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Johan Hedberg [Wed, 24 Oct 2012 18:12:00 +0000 (21:12 +0300)]
Bluetooth: Add missing feature test macros
This patch adds missing feature test macros needed for various use cases
and also sorts the macros according to the feature bit location in the
feature mask (for easy lookup).
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Johan Hedberg [Wed, 24 Oct 2012 18:11:59 +0000 (21:11 +0300)]
Bluetooth: Fix updating host feature bits for LE
When LE has been enabled with the simultaneous BR/EDR & LE parameter set
to true we should also update the host features stored in struct hci_dev
accordingly.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Johan Hedberg [Wed, 24 Oct 2012 18:11:58 +0000 (21:11 +0300)]
Bluetooth: mgmt: Restrict BR/EDR settings to BR/EDR-only adapters
This patch makes sure that settings which are specific for BR/EDR
capable adapters are not allowed for non-BR/EDR (e.g. LE-only) adapters.
Instead, a "not supported" error is returned of such a setting is
attempted to be set for a non-BR/EDR adapter.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Johan Hedberg [Wed, 24 Oct 2012 18:11:57 +0000 (21:11 +0300)]
Bluetooth: Fix HCI command sending when powering on LE-only adapters
This patch makes sure that we don't send BR/EDR-only commands for
LE-only adapters when they get powered on. Doing this would just cause
command errors.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Denis Kirjanov [Mon, 22 Oct 2012 13:22:01 +0000 (17:22 +0400)]
Bluetooth:Replace list_for_each with list_for_each_entry() helper
Replace list_for_each with list_for_each_entry() helper
Signed-off-by: Denis Kirjanov <kirjanov@gmail.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Gustavo Padovan [Wed, 24 Oct 2012 13:18:41 +0000 (11:18 -0200)]
Bluetooth: Replace *_init() for *_setup()
le_init() and bredr_init() are now called le_setup() and bredr_setup() to
avoid duplicates names over the tree even if they are all static.
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Johan Hedberg [Fri, 19 Oct 2012 17:57:49 +0000 (20:57 +0300)]
Bluetooth: Read adversiting channel TX power during init sequence
This patch adds the reading of the LE advertising channel TX power to
the HCI init sequence of LE-capable controllers. This data will be used
e.g. for inclusion in the advertising data packets when advertising is
enabled.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Johan Hedberg [Fri, 19 Oct 2012 17:57:47 +0000 (20:57 +0300)]
Bluetooth: Add setting of the LE event mask
This patch adds setting of the LE event mask to the HCI init procedure
for LE-capable controllers. Right now we only set the default mask which
is good enough for the events available in the 4.0 core specification.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Johan Hedberg [Fri, 19 Oct 2012 17:57:46 +0000 (20:57 +0300)]
Bluetooth: Fix LE MTU reporting for HCIGETDEVINFO
This patch fixes the use of le_mtu and le_pkts values in the
HCIGETDEVINFO ioctl for LE-only controllers.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Johan Hedberg [Fri, 19 Oct 2012 17:57:45 +0000 (20:57 +0300)]
Bluetooth: Add initial support for LE-only controllers
This patch splits off most the HCI init sequence commands from a fixed
set into a conditional one that is sent once the HCI_Read_Local_Features
and HCI_Read_Local_Version_Information commands complete. This is
necessary since many of the current fixed commands are not allowed for
LE-only controllers.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Syam Sidhardhan [Tue, 23 Oct 2012 13:32:18 +0000 (19:02 +0530)]
Bluetooth: Replace include linux/module.h with linux/export.h
include <linux/export.h> is the right to go here.
Signed-off-by: Syam Sidhardhan <s.syam@samsung.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Syam Sidhardhan [Tue, 23 Oct 2012 13:32:16 +0000 (19:02 +0530)]
Bluetooth: trivial: Remove newline before EOF
Trivial fix.
Signed-off-by: Syam Sidhardhan <s.syam@samsung.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Mat Martineau [Tue, 23 Oct 2012 22:24:23 +0000 (15:24 -0700)]
Bluetooth: Start channel move when socket option is changed
Channel moves are triggered by changes to the BT_CHANNEL_POLICY
sockopt when an ERTM or streaming-mode channel is connected.
Moves are only started if enable_hs is true.
Signed-off-by: Mat Martineau <mathewm@codeaurora.org>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Mat Martineau [Tue, 23 Oct 2012 22:24:22 +0000 (15:24 -0700)]
Bluetooth: Do not retransmit data during a channel move
Do not retransmit previously-sent data when a "receiver ready" s-frame
with the "final" flag is received during a move.
The ERTM state machines will resynchronize at the end of a channel
move, and the state machine needs to avoid state changes during a
move.
Signed-off-by: Mat Martineau <mathewm@codeaurora.org>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Acked-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Mat Martineau [Tue, 23 Oct 2012 22:24:21 +0000 (15:24 -0700)]
Bluetooth: Ignore BR/EDR packet size constraints when fragmenting for AMP
When operating over BR/EDR, ERTM accounts for the maximum over-the-air
packet size when setting the PDU size. AMP controllers do not use the
same over-the-air packets, so the PDU size should only be based on the
HCI MTU of the AMP controller.
Signed-off-by: Mat Martineau <mathewm@codeaurora.org>
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Mat Martineau [Tue, 23 Oct 2012 22:24:20 +0000 (15:24 -0700)]
Bluetooth: Configure appropriate timeouts for AMP controllers
The L2CAP spec recommends specific retransmit and monitor timeouts for
ERTM channels that are on AMP controllers. These timeouts are
calculated from the AMP controller's best effort flush timeout.
BR/EDR controllers use the default retransmit and monitor timeouts.
Signed-off-by: Mat Martineau <mathewm@codeaurora.org>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Mat Martineau [Tue, 23 Oct 2012 22:24:19 +0000 (15:24 -0700)]
Bluetooth: Do not send data during channel move
Outgoing ERTM data is queued during a channel move. The ERTM state
machine is partially reset at the start of a move, and must be
resynchronized with the remote state machine at the end of the move.
Data is not sent so that there are no state transitions between the
partial reset and the resync.
Streaming mode frames are dropped during a move.
Signed-off-by: Mat Martineau <mathewm@codeaurora.org>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Acked-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Mat Martineau [Tue, 23 Oct 2012 22:24:18 +0000 (15:24 -0700)]
Bluetooth: Flag ACL frames as complete for AMP controllers
AMP controllers expect to transmit only "complete" ACL frames. These
frames have both the "start" and "cont" bits set. AMP does not allow
fragmented ACLs.
Signed-off-by: Mat Martineau <mathewm@codeaurora.org>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Acked-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Mat Martineau [Tue, 23 Oct 2012 22:24:17 +0000 (15:24 -0700)]
Bluetooth: Handle physical link completion
Several different actions may be taken when an AMP physical link
becomes available. A channel being created on an AMP controller must
continue the connection process. A channel being moved needs to
either send a move request or a move response. A failed physical link
will revert to using a BR/EDR controller if possible.
Signed-off-by: Mat Martineau <mathewm@codeaurora.org>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Acked-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Mat Martineau [Tue, 23 Oct 2012 22:24:16 +0000 (15:24 -0700)]
Bluetooth: Add move confirm response handling
The move confirm response concludes the channel move command sequence.
Receipt of this command indicates that data may begin to flow again.
Signed-off-by: Mat Martineau <mathewm@codeaurora.org>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Acked-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Mat Martineau [Tue, 23 Oct 2012 22:24:15 +0000 (15:24 -0700)]
Bluetooth: Add logical link confirm
The logical link confirm callback is executed when the AMP controller
completes its logical link setup. During a channel move, a newly
formed logical link allows a move responder to send a move channel
response. A move initiator will send a move channel confirm. A
failed logical link will end the channel move and send an appropriate
response or confirm command indicating a failure.
If the channel is being created on an AMP controller, L2CAP
configuration is completed after the logical link is set up.
Signed-off-by: Mat Martineau <mathewm@codeaurora.org>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Mat Martineau [Tue, 23 Oct 2012 22:24:14 +0000 (15:24 -0700)]
Bluetooth: Move channel response
The move response command includes a result code indicating
"pending", "success", or "failure" status. A pending result is
received when the remote address is still setting up a physical link,
and will be followed by success or failure. On success, logical link
setup will proceed. On failure, the move is stopped. The receiver of
a move channel response must always follow up by sending a move
channel confirm command.
Signed-off-by: Mat Martineau <mathewm@codeaurora.org>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Mat Martineau [Tue, 23 Oct 2012 22:24:13 +0000 (15:24 -0700)]
Bluetooth: Add state to hci_chan
On an AMP controller, hci_chan maps to a logical link. When a channel
is being moved, the logical link may or may not be connected already.
The hci_chan->state is used to determine the existance of a useable
logical link so the link can be either used or requested.
Signed-off-by: Mat Martineau <mathewm@codeaurora.org>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Acked-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Mat Martineau [Tue, 23 Oct 2012 22:24:12 +0000 (15:24 -0700)]
Bluetooth: Add move channel confirm handling
After sending a move channel response, a move responder waits for a
move channel confirm command. If the received command has a
"confirmed" result the move is proceeding, and "unconfirmed" means the
move has failed and the channel will not change controllers.
Signed-off-by: Mat Martineau <mathewm@codeaurora.org>
Acked-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Mat Martineau [Tue, 23 Oct 2012 22:24:11 +0000 (15:24 -0700)]
Bluetooth: Add new ERTM receive states for channel move
Two new states are required to implement channel moves with the ERTM
receive state machine.
The "WAIT_P" state is used by a move responder to wait for a "poll"
flag after a move is completed (success or failure). "WAIT_F" is
similarly used by a move initiator to wait for a "final" flag when the
move is completing. In either state, the reqseq value in the
poll/final frame tells the state machine exactly which frame should be
expected next.
Signed-off-by: Mat Martineau <mathewm@codeaurora.org>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Acked-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Mat Martineau [Tue, 23 Oct 2012 22:24:10 +0000 (15:24 -0700)]
Bluetooth: Channel move request handling
On receipt of a channel move request, the request must be validated
based on the L2CAP mode, connection state, and controller
capabilities. ERTM channels must have their state machines cleared
and transmission paused while the channel move takes place.
If the channel is being moved to an AMP controller then
an AMP physical link must be prepared. Moving the channel back to
BR/EDR proceeds immediately.
Signed-off-by: Mat Martineau <mathewm@codeaurora.org>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Acked-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Mat Martineau [Tue, 23 Oct 2012 22:24:09 +0000 (15:24 -0700)]
Bluetooth: Lookup channel structure based on DCID
Processing a move channel request involves getting the channel
structure using the destination channel ID. Previous code could only
look up using the source channel ID.
Signed-off-by: Mat Martineau <mathewm@codeaurora.org>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Acked-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Mat Martineau [Tue, 23 Oct 2012 22:24:08 +0000 (15:24 -0700)]
Bluetooth: Remove unnecessary intermediate function
Resolves a conflict resolution issue in "Bluetooth: Fix L2CAP coding
style". The remaining connect and create channel response handler is
renamed to better reflect its use for both response types.
Signed-off-by: Mat Martineau <mathewm@codeaurora.org>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Acked-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Mat Martineau [Tue, 23 Oct 2012 22:24:07 +0000 (15:24 -0700)]
Bluetooth: Add L2CAP create channel request handling
The L2CAP create channel request is very similar to an L2CAP connect
request, but it has an additional parameter for the controller ID. If
the controller id is 0, the channel is set up on the BR/EDR controller
(just like a connect request). Using a valid high speed controller ID
will cause the channel to be initially created on that high speed
controller. While the L2CAP data will be initially routed over the
AMP controller, the L2CAP fixed signaling channel only uses BR/EDR.
When a create channel request is received for a high speed controller,
a pending response is always sent first. After the high speed
physical and logical links are complete a success response will be
sent.
Signed-off-by: Mat Martineau <mathewm@codeaurora.org>
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Mat Martineau [Tue, 23 Oct 2012 22:24:06 +0000 (15:24 -0700)]
Bluetooth: Add new l2cap_chan struct members for high speed channels
An L2CAP channel using high speed continues to be associated with a
BR/EDR l2cap_conn, while also tracking an additional hci_conn
(representing a physical link on a high speed controller) and hci_chan
(representing a logical link). There may only be one physical link
between two high speed controllers. Each physical link may contain
several logical links, with each logical link representing a channel
with specific quality of service.
During a channel move, the destination channel id, current move state,
and role (initiator vs. responder) are tracked and used by the channel
move state machine. The ident value associated with a move request
must also be stored in order to use it in later move responses.
The active channel is stored in local_amp_id.
Signed-off-by: Mat Martineau <mathewm@codeaurora.org>
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Alan Cox [Thu, 11 Oct 2012 16:25:14 +0000 (17:25 +0100)]
brcm80211: remove some truely barftastic code
It's not used or called but please make it go away before someone copies or
uses it
Signed-off-by: Alan "minus lunch" Cox <alan@linux.intel.com>
Acked-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Arend van Spriel [Wed, 10 Oct 2012 18:13:11 +0000 (11:13 -0700)]
brcmfmac: remove 'always false' condition from brcmf_c_mkiovar_bsscfg
The parameter buflen is unsigned so the condition buflen < 0 is
always false. The patch fixes the if statement checking the buffer
length.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Franky Lin [Wed, 10 Oct 2012 18:13:08 +0000 (11:13 -0700)]
brcmfmac: fix sparse warnings
Following sparse warning is fixed:
drivers/net/wireless/brcm80211/brcmfmac/wl_cfg80211.c:2518:21: warning: symbol 'brcmf_find_wpaie' was not declared. Should it be static?
drivers/net/wireless/brcm80211/brcmfmac/wl_cfg80211.c:3768:1: warning: symbol 'brcmf_set_management_ie' was not declared. Should it be static?
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Dan Carpenter [Wed, 10 Oct 2012 18:13:07 +0000 (11:13 -0700)]
brcmfmac: Using zero instead of NULL
Sparse complains that we use zero instead of NULL here. In fact, the
initialization is wrong and should be removed. Doing these kinds of
bogus initializations means that GCC can't detect unitialized variables
and leads to bugs.
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Rajkumar Manoharan [Wed, 10 Oct 2012 17:33:02 +0000 (23:03 +0530)]
ath9k: perform ANI cycle in idle state
As of now the ANI cycle is executed only when the chip is awake.
On idle state case, the station wakes up from network sleep for
beacon reception. Since most of the time, ANI cycle is not syncing
with beacon wakeup, ANI cycle is ignored. Approx 5 mins once, the
calibration is performed. This could affect the connection stability
when the station is idle for long. Even though the OFDM and CCK phy
error rates are too high, ANI is unable to tune its immunity level
as quick enough due to rare execution.
Here the experiment shows that OFDM and CCK levels are at default
even on higher phy error rate.
listenTime=44 OFDM:3 errs=121977/s CCK:2 errs=440818/s ofdm_turn=1
This change ensures that ANI calibration will be exectued atleast
once for every 10 seconds. The below result shows improvements and
immunity levels are adopted quick enough.
listenTime=557 OFDM:4 errs=752/s CCK:4 errs=125/s ofdm_turn=0
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Christian Lamparter [Sat, 6 Oct 2012 18:42:54 +0000 (20:42 +0200)]
carl9170: handle traps from firmware loader
This patch changes the way the driver deals with
command responses and traps which are sent through
the special interrupt input endpoint 3.
While the carl9170 firmware does not use this
endpoint for command responses or traps, the
firmware loader on the device does. It uses it
to notify the host about 'watchdog triggered'
in case the firmware/hardware has crashed.
Note:
Even without this patch, the driver is still
able to detect the mishap and reset the device.
But previously it did that because the trap
event caused an out-of-order message sequence
number error, which also triggered a reset.
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Andrei Emeltchenko [Fri, 5 Oct 2012 20:57:49 +0000 (13:57 -0700)]
mwifiex: Using %*phD instead of print_hex_dump_bytes
Make output more readable and remove unneeded function call.
...
mwifiex_sdio mmc0:0001:1: last_cmd_index = 3
last_cmd_id:
00000000: 16 00 cd 00 83 00 df 00 28 00 ........(.
...
would be changed to:
...
mwifiex_sdio mmc0:0001:1: last_cmd_index = 3
mwifiex_sdio mmc1:0001:1: last_cmd_id: 16 00 cd 00 83 00 df 00 28 00
...
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Bing Zhao [Fri, 5 Oct 2012 20:57:48 +0000 (13:57 -0700)]
mwifiex: use sizeof(array) to print_hex_dump_bytes
DBG_CMD_NUM is the number of commands, not the actual bytes of
data for printing.
Also remove the duplicated DBG_CMD_NUM definition.
Reported-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Stanislaw Gruszka [Fri, 5 Oct 2012 11:44:15 +0000 (13:44 +0200)]
rt2800: comment tx power settings
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Acked-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Stanislaw Gruszka [Fri, 5 Oct 2012 11:44:14 +0000 (13:44 +0200)]
rt2800: allow to reduce tx power on devices not exporting power limit
Some rt2800 devices don't have their calibrated max eirp tx power in
their calibration data. For those devices reduce tx power according to
difference between regulatory max channel power and requested tx power.
This patch is based on Helmut Schaa work.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Acked-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Stanislaw Gruszka [Fri, 5 Oct 2012 11:44:13 +0000 (13:44 +0200)]
rt2800: pass channel pointer to rt2800_config_txpower
Preparation for use regulatory max channel power in TX power delta
calculations.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Stanislaw Gruszka [Fri, 5 Oct 2012 11:44:12 +0000 (13:44 +0200)]
rt2800: use eeprom OFDM 6M TX power as criterion
Don use TX_PWR_CFG_0 register value of OFDM 6M tx power as criterion
since it can be changed. The same do vendor driver (see
AsicAdjustSingleSkuTxPower and AsicGetTxPowerOffset functions from
2011_0719_RT3070_RT3370_RT5370_RT5372_Linux_STA_V2.5.0.3_DPO).
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Stanislaw Gruszka [Fri, 5 Oct 2012 11:44:11 +0000 (13:44 +0200)]
rt2800: compensate tx power also for non 11b rates on 2GHz
We skip compensate calculation for non 11b rates on 2.4GHz band. I do
not see that on vendor driver
(2011_0719_RT3070_RT3370_RT5370_RT5372_Linux_STA_V2.5.0.3_DPO).
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Helmut Schaa <helmut.schaa@googlemail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Stanislaw Gruszka [Fri, 5 Oct 2012 11:44:10 +0000 (13:44 +0200)]
rt2800: limit TX_PWR_CFG_ values to 0xc
Based on AsicAdjustTxPower function from vendor driver
(2011_0719_RT3070_RT3370_RT5370_RT5372_Linux_STA_V2.5.0.3_DPO)
limit per rate TX power values we program into TX_PWR_CFG_ registers.
Note that on some configurations (devices/rates) is allowed to use
bigger values than 0xc, but we use safe maximum value for now. Further
work need to be done to allow use bigger values than 0xc.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Stanislaw Gruszka [Fri, 5 Oct 2012 11:44:09 +0000 (13:44 +0200)]
rt2800: use BBP_R1 for setting tx power
TX power delta can be negative. TX_PWR_CFG_ registers allow to set delta
only in range between 0 dBm and 15 dBm (4 bits for each rate). Se we
need to use BBP_R1 to configure negative deltas.
Not utilize +6 dBm increasing BBP_R1 option for safety reason. For now,
this can be used for devices, which export maximum allowed TX power
value.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Helmut Schaa <helmut.schaa@googlemail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Sven Eckelmann [Thu, 4 Oct 2012 17:43:15 +0000 (19:43 +0200)]
ath_hw: Use common REG_WRITE parameter order
All defines for REG_WRITE in Atheros wireless drivers use the order "ah",
"register" and "value". hw.c is the only file using the order "ah", "value" and
"register".
drivers/net/wireless/ath/ath9k/hw.h:#define REG_WRITE(_ah, _reg, _val) \
drivers/net/wireless/ath/key.c:#define REG_WRITE(_ah, _reg, _val) (common->ops->write)(_ah, _val, _reg)
This inconsistent definition can easily lead to implementation errors. The
modification doesn't change the behavior of the driver or the generated code.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Acked-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Andy Shevchenko [Tue, 2 Oct 2012 14:19:44 +0000 (17:19 +0300)]
rtlwifi: rtl8192ce: rtl8192cu: use %*phC to dump small buffers
The patch changes a bit trace output format in the rtl_cam_program_entry() to
print prefix and the actual data on the same line. Moreover the %*phC outputs
each byte as 2 hex digits, which is slightly different to the original %x.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
ACKed-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Dan Carpenter [Tue, 2 Oct 2012 08:32:34 +0000 (11:32 +0300)]
orinoco_usb: clean up some signedness issues
In ezusb_read_ltv() we had a comparison "(bufsize < 0)" which was never
true because bufsize was unsigned. I looked at the implications of
that. If we passed a negative number to ezusb_access_ltv() then it
would be used as the size parameter of the memcpy() because that
function uses min_t(int, exp_len, ans_size).
But fortunately when I looked at the callers, bufsize is not controlled
by the user and it's never negative. So these signedness mistakes have
no impact.
I removed the always false check from ezusb_read_ltv() and I changed the
types in ezusb_access_ltv() and made the variables unsigned.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Hauke Mehrtens [Sun, 30 Sep 2012 22:12:54 +0000 (00:12 +0200)]
bcma: do not initialize deactivated PCIe cores
Before it was tried to initialize the deactivated PCIe core in client
mode, but this causes the SoC to hang. Just do not initialize it at all
and ignore the core it is not working and nothing is connected to it
when the specific bit is set in the boardflags.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Peter Senna Tschudin [Wed, 10 Oct 2012 16:38:17 +0000 (18:38 +0200)]
ath/ath9k/ar9003_eeprom.c: Remove semicolon after if
This patch remove a semicolon after if(...) that is preventing the
error check to work correctly. Removing this semicolon will change the
code behavior, but this is intended.
The semantic patch that finds this problem is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@r1@
position p;
@@
if (...);@p
@script:python@
p0 << r1.p;
@@
// Emacs org-mode output
cocci.print_main("", p0)
cocci.print_secs("", p0)
// </smpl>
Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Sujith Manoharan [Sun, 30 Sep 2012 03:33:37 +0000 (09:03 +0530)]
ath9k: Fix BT_OP_SCAN usage
BT_OP_SCAN is applicable only for pre-MCI WLAN/BT combo chips
and using it for MCI-based cards is incorrect. Fix this by
cleaning up its usage.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Sujith Manoharan [Sun, 30 Sep 2012 03:33:20 +0000 (09:03 +0530)]
ath9k: Use a helper routine for MCI/FTP tuning
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Hauke Mehrtens [Sat, 29 Sep 2012 18:40:18 +0000 (20:40 +0200)]
bcma: add an extra pcie core struct
The BCM4706 has two PCIe host controller on the bcma bus. For PCIe
client mode it is assumed that there is only one PCIe controller so the
PCIe driver, like b43 and brcmsmac are accessing the first PCIe
controller when they want to issue a operation on the host controller.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Hauke Mehrtens [Sat, 29 Sep 2012 18:38:11 +0000 (20:38 +0200)]
bcma: use fallback sprom if sprom on card was not valid
Sometimes the PCIe card indicates that it has a sprom somewhere and we
are able to read the memory region, but it is empty and not valid. In
these cases we should try to use the fallback sprom as a last chance.
This is the case for the PCIe cards in my ASUS RT-N66U (BCM4706 + 2
times BCM4331) and I have heard of someone having the same problem with
an other PCIe card connected to an other Broadcom SoC.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Hauke Mehrtens [Sat, 29 Sep 2012 18:36:18 +0000 (20:36 +0200)]
ssb: add attribute to indicate a parallel flash is available
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Hauke Mehrtens [Sat, 29 Sep 2012 18:36:17 +0000 (20:36 +0200)]
ssb: move parallel flash config into an own struct
This is a preparing step for adding serial flash support.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Hauke Mehrtens [Sat, 29 Sep 2012 18:33:53 +0000 (20:33 +0200)]
bcma: add some more flash chips for serial flash
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Hauke Mehrtens [Sat, 29 Sep 2012 18:33:52 +0000 (20:33 +0200)]
bcma: extract drv_cc in bcma_core_mips_flash_detect()
This makes the code more readable
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Hauke Mehrtens [Sat, 29 Sep 2012 18:33:51 +0000 (20:33 +0200)]
bcma: mark nflash if it is the boot flash
There are some devices which are able to boot from nand flash and other
are using a serial flash for booting. Add a bool to indicate that the
device is booted from that flash chip and not from some other chip also
connected to the SoC. This is needed to find the nvram, as it is stored
on the flash the devices booted from.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Hauke Mehrtens [Sat, 29 Sep 2012 18:33:50 +0000 (20:33 +0200)]
bcma: add and use constants for the flash windows
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Hauke Mehrtens [Sat, 29 Sep 2012 18:33:49 +0000 (20:33 +0200)]
bcma: mark pflash as present when available
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Hauke Mehrtens [Sat, 29 Sep 2012 18:29:50 +0000 (20:29 +0200)]
bcma: init sprom struct earlier
The PCIe host driver and the chip common initialisation accesses the
sprom struct, but it is not initialized when these functions are run.
Move the sprom parsing up in to do it earlier.
As we need the chip common core rev and some other attributes from the
chip common core, the early initialization is done before accessing the
sprom.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Hauke Mehrtens [Sat, 29 Sep 2012 18:29:49 +0000 (20:29 +0200)]
bcma: just do the necessary things in early register on SoCs
Some parts of the initialization for chip common and the pcie core are
accessing the sprom struct, but it is not initialized at that stage.
Just do the necessary thing in the early register on SoCs and not the
complete initialization to read out the nvram from the flash chip.
After it is possible to read out the nvram, the sprom should be parsed
from it and the full initialization of the cores should be run.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
John W. Linville [Fri, 19 Oct 2012 19:48:17 +0000 (15:48 -0400)]
Merge branch 'for-john' of git://git./linux/kernel/git/iwlwifi/iwlwifi-next
John W. Linville [Fri, 19 Oct 2012 19:36:53 +0000 (15:36 -0400)]
Merge branch 'for-john' of git://git./linux/kernel/git/jberg/mac80211-next
John W. Linville [Fri, 19 Oct 2012 19:22:27 +0000 (15:22 -0400)]
Merge branch 'master' of git://git./linux/kernel/git/bluetooth/bluetooth-next
Marco Porsch [Wed, 10 Oct 2012 19:39:50 +0000 (12:39 -0700)]
mac80211: make client powersave independent of interface type
This patch prepares mac80211 for a later implementation of mesh or
ad-hoc powersave clients.
The structures related to powersave (buffer, TIM map, counters) are
moved from the AP-specific interface structure to a generic structure
that can be embedded into any interface type.
The functions related to powersave are prepared to allow easy
extension with different interface types. For example with:
+ } else if (sta->sdata->vif.type == NL80211_IFTYPE_MESH_POINT) {
+ ps = &sdata->u.mesh.ps;
Some references to the AP's beacon structure are removed where they
were obviously not used.
The patch compiles without warning and has been briefly tested as AP
interface with one client in PS mode.
Signed-off-by: Marco Porsch <marco.porsch@etit.tu-chemnitz.de>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Antonio Quartulli [Tue, 16 Oct 2012 06:39:22 +0000 (08:39 +0200)]
nl/cfg80211: force scan using an AP vif if requested
If the user wants to scan using a vif configured as AP,
cfg80211 must give him a chance to do it, even if this
will disrupt the stations performance due to off-channel
scanning. To do so, this patch adds a 'force' flag to the
SCAN_TRIGGER command which tells cfg80211 to perform the
scanning operation even if the vif is an AP and the
beaconing has already started.
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Andrei Emeltchenko [Thu, 18 Oct 2012 10:16:19 +0000 (13:16 +0300)]
Bluetooth: AMP: Get amp_mgr reference in HS hci_conn
When assigning amp_mgr in hci_conn (type AMP_LINK) get also reference.
In hci_conn_del those references would be put for both conn types
AMP_LINK and ACL_LINK associated with amp_mgr.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Beni Lev [Mon, 27 Aug 2012 09:49:39 +0000 (12:49 +0300)]
cfg80211: add cfg80211 exported function tracing
Also add tracing to the API functions that drivers
(and mac80211) can call in cfg80211.
Signed-off-by: Beni Lev <beni.lev@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Beni Lev [Tue, 31 Jul 2012 15:48:27 +0000 (18:48 +0300)]
cfg80211: add tracing to rdev-ops
Add tracing to make debugging cfg80211/mac80211
(or full-mac driver) interaction easier.
Signed-off-by: Beni Lev <beni.lev@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Reviewed-by: Hila Gonen <hila.gonen@intel.com>
Tested-by: Hila Gonen <hila.gonen@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
[add a cast to int to sizeof() to avoid warning]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Hila Gonen [Wed, 27 Jun 2012 14:19:42 +0000 (17:19 +0300)]
cfg80211: add wrappers for registered_device_ops
This will allow adding central tracing like in mac80211.
Signed-off-by: Hila Gonen <hila.gonen@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Sujith Manoharan [Thu, 18 Oct 2012 04:49:28 +0000 (10:19 +0530)]
cfg80211: Disallow HT/WEP in IBSS mode
Currently, a user is allowed to choose a HT operating channel
with WEP when creating an IBSS network. WEP is not allowed
in HT configuration - this patch ensures that such requests
are denied.
Signed-off-by: Sujith Manoharan <c_manoha@qti.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Marco Porsch [Thu, 18 Oct 2012 03:21:30 +0000 (20:21 -0700)]
mac80211: fix copy-paste typo in Kconfig
Signed-off-by: Marco Porsch <marco.porsch@etit.tu-chemnitz.de>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Johannes Berg [Sun, 30 Sep 2012 15:12:45 +0000 (17:12 +0200)]
mac80211: use __printf attribute in debugfs
The internal function mac80211_format_buffer() has a
printf-style argument list, so add the attribute to
have gcc verify that list.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Johannes Berg [Sun, 30 Sep 2012 15:08:35 +0000 (17:08 +0200)]
mac80211: remove some unused code
There are a number of unused variables that gcc
pointed out (when building with W=1) as well as
some conditions that can never be true due to
the datatypes used: unsigned values can't be
less than zero. Remove this code.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Johannes Berg [Sun, 30 Sep 2012 15:07:19 +0000 (17:07 +0200)]
mac80211: remove unimplemented mesh vendor sync
There's no vendor-specific mesh sync implemented
and there don't need to be dummy handlers that
only print messages, so remove that code. While
at it, also constify the mesh sync ops.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Arend van Spriel [Fri, 12 Oct 2012 10:28:16 +0000 (12:28 +0200)]
wireless: remove duplicate enum ieee80211_eid definitions
WLAN_EID_WPA and WLAN_EID_GENERIC mapped to the same value
as WLAN_EID_VENDOR_SPECIFIC. The last one being more in line
with the standard specification. Removing WLAN_EID_WPA and
WLAN_EID_GENERIC as there are no longer drivers using these.
Cc: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Arend van Spriel [Fri, 12 Oct 2012 10:28:15 +0000 (12:28 +0200)]
wireless: gelic: make use of WLAN_EID_VENDOR_SPECIFIC
The include file linux/ieee80211.h contains three definitions for
the same thing in enum ieee80211_eid due to historic changes:
/* Information Element IDs */
enum ieee80211_eid {
:
WLAN_EID_WPA = 221,
WLAN_EID_GENERIC = 221,
WLAN_EID_VENDOR_SPECIFIC = 221,
:
};
The standard refers to this as "vendor specific" element so the
other two definitions are better not used. This patch changes the
wireless drivers to use one definition, ie. WLAN_EID_VENDOR_SPECIFIC.
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Arend van Spriel [Fri, 12 Oct 2012 10:28:14 +0000 (12:28 +0200)]
wireless: drivers: make use of WLAN_EID_VENDOR_SPECIFIC
The include file linux/ieee80211.h contains three definitions for
the same thing in enum ieee80211_eid due to historic changes:
/* Information Element IDs */
enum ieee80211_eid {
:
WLAN_EID_WPA = 221,
WLAN_EID_GENERIC = 221,
WLAN_EID_VENDOR_SPECIFIC = 221,
:
};
The standard refers to this as "vendor specific" element so the
other two definitions are better not used. This patch changes the
wireless drivers to use one definition, ie. WLAN_EID_VENDOR_SPECIFIC.
Cc: Jouni Malinen <j@w1.fi>
Cc: Dan Williams <dcbw@redhat.com>
Cc: Larry Finger <Larry.Finger@lwfinger.net>
Acked-by: Kalle Valo <kvalo@qca.qualcomm.com> [ath6kl]
Acked-by: Bing Zhao <bzhao@marvell.com> [mwifiex]
Acked-by: Stanislav Yakovlev <stas.yakovlev@gmail.com> [ipw2x00]
Signed-off-by: Arend van Spriel <arend@broadcom.com>
[change libipw as well]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Sujith Manoharan [Fri, 12 Oct 2012 12:05:45 +0000 (17:35 +0530)]
mac80211: Notify new IBSS network creation
Initialization of beacon transmission in IBSS mode depends
on whether a new BSS is being created or joined. When joining
an existing IBSS network, beaconing has to start only after
a TSF-sync has happened - this is explained in 11.1.4.
Introduce a new parameter in the BSS information structure to
indicate creator/joiner mode.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Sam Leffler [Fri, 12 Oct 2012 04:03:35 +0000 (21:03 -0700)]
mac80211: add support for tx to abort low priority scan requests
Use NL80211_SCAN_FLAG_LOW_PRIORITY flag in mac80211's scan state
machine to prematurely terminate scan operations if outbound
traffic collides. This is useful for marking background scans so
they don't affect throughput.
Signed-off-by: Sam Leffler <sleffler@chromium.org>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
[set feature flag only if software scan is used]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Sam Leffler [Fri, 12 Oct 2012 04:03:34 +0000 (21:03 -0700)]
cfg80211: add support for flushing old scan results
Add an NL80211_SCAN_FLAG_FLUSH flag that causes old bss cache
entries to be flushed on scan completion. This is useful for
collecting guaranteed fresh scan/survey result (e.g. on resume).
For normal scan, flushing only happens on successful completion
of a scan; i.e. it does not happen if the scan is aborted.
For scheduled scan, previous scan results are flushed everytime
when we get new scan results.
This feature is enabled by default. Drivers can disable it by
unsetting the NL80211_FEATURE_SCAN_FLUSH flag.
Signed-off-by: Sam Leffler <sleffler@chromium.org>
Tested-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
[invert polarity of feature flag to account for old kernels]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Johannes Berg [Fri, 12 Oct 2012 08:55:53 +0000 (10:55 +0200)]
wireless: use OR operation to set wiphy features
The next patch will introduce a flag that is set
by default in cfg80211 so drivers and mac80211
need to use |= to set features they have so that
they don't clear the already-set feature.
We could set the flag in wiphy_register() instead
of wiphy_new() to avoid this patch, but then the
drivers couldn't *unset* flags they don't want to
use even though the implementation is generic.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Sam Leffler [Fri, 12 Oct 2012 04:03:32 +0000 (21:03 -0700)]
cfg80211: add scan flag to indicate its priority
Add NL80211_SCAN_FLAG_LOW_PRIORITY flag support. It tells drivers
that this is a low priority scan request, so that they can take
necessary action.
Drivers need to advertise low priority scan capability during
registration.
Signed-off-by: Sam Leffler <sleffler@chromium.org>
Tested-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Amitkumar Karwar [Fri, 12 Oct 2012 04:03:33 +0000 (21:03 -0700)]
cfg80211: code rearrangement to avoid forward declarations
bss_release() and __cfg80211_unlink_bss() function definitions
are moved at the begining of the file. They are used in next
patch in this series.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Sam Leffler [Fri, 12 Oct 2012 04:03:31 +0000 (21:03 -0700)]
{nl,cfg}80211: add a flags word to scan requests
Add a flags word to direct and scheduled scan requests; it will
be used for control of optional behaviours such as flushing the
bss cache prior to doing a scan.
Signed-off-by: Sam Leffler <sleffler@chromium.org>
Tested-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Mahesh Palivela [Thu, 11 Oct 2012 08:04:52 +0000 (08:04 +0000)]
{nl,cfg}80211: Peer STA VHT caps
To save STAs VHT caps in AP mode
Signed-off-by: Mahesh Palivela <maheshp@posedge.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
projects / GitHub / exynos8895 / android_kernel_samsung_universal8895.git / log