isdn: avoid races in capidrv

In several places, capidrv sends a CAPI message to the ISDN
device and then updates its internal state accordingly.
If the response message from the device arrives before the
state is updated, it may be rejected or processed incorrectly.
Avoid these races by updating the state before emitting the
message.

Impact: bugfix
Signed-off-by: Tilman Schmidt <tilman@imap.cc>
Acked-by: Karsten Keil <keil@b1-systems.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

isdn: accept CAPI Informational Info values as success

Info values in the 0x00xx range are defined in the CAPI standard
as "Informational, message processed successfully". Therefore a
CONNECT_B3_CONF message with an Info value in that range should
open an NCCI just as with Info==0.

Impact: minor bugfix
Signed-off-by: Tilman Schmidt <tilman@imap.cc>
Acked-by: Karsten Keil <keil@b1-systems.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

Documentation: expand isdn/INTERFACE.CAPI document

- Note that send_message() may be called in interrupt context.
- Describe the storage of CAPI messages and payload data in SKBs.
- Add more details to the description of the _cmsg structure.
- Describe kernelcapi debugging output.

Impact: documentation
Signed-off-by: Tilman Schmidt <tilman@imap.cc>
Signed-off-by: David S. Miller <davem@davemloft.net>

be2net: Bug fix to properly update ethtool tx-checksumming after ethtool -K <ifname> tx off

This is a fix for a bug which was a result of wrong use of checksum offload flag.
The status of tx-checksumming was not changed from on to off
after a 'ethtool -K <ifname> tx off' operation.
Use the proper checksum offload flag NETIF_F_HW_CSUM instead of
NETIF_F_IP_CSUM and NETIF_F_IPV6_CSUM.
Patch is against net-2.6 tree.

Signed-off-by: Ajit Khaparde <ajitk@serverengines.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

be2net: Fix a typo in be_cmds.h

MCC_STATUS_NOT_SUPPORTED should be decimal 66 not hex 66.
This patch fixes this typo. Patch against net-2.6 tree.

Signed-off-by: Ajit Khaparde <ajitk@serverengines.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

be2net: Bug Fix while accounting of multicast frames during netdev stats update

While updating the statistics to be passed via the get_stats,
tx multicast frames were being accounted instead of rx multicast frames.
This patch fixes the bug. This patch is against the net-2.6 tree.

Signed-off-by: Ajit Khaparde <ajitk@serverengines.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

qlge: Fix lock/mutex warnings.

Get rid of spinlock and private mutex usage for exclusive access to the
HW semaphore register.  rtnl_lock already creates exclusive access to
this register in all driver API.
Add rtnl to firmware worker threads that also use the HW semaphore register.

Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

qlge: Fix queueing of firmware handler in ISR.

Check that we are not already polling firmware events before we queue the
firmware event worker, then disable firmware interrupts.
Otherwise we can queue the same event multiple times.

Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

qlge: Fix some bit definitions for reset register.

Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

connector: Fix incompatible pointer type warning

Commit 7069331 (connector: Provide the sender's credentials to the
callback, 2009-10-02) changed callbacks to take two arguments but missed
this one.

drivers/connector/cn_proc.c: In function ‘cn_proc_init’:
drivers/connector/cn_proc.c:263: warning: passing argument 3 of
‘cn_add_callback’ from incompatible pointer type

Signed-off-by: Stephen Boyd <bebarino@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

wext: let get_wireless_stats() sleep

A number of drivers (recently including cfg80211-based ones)
assume that all wireless handlers, including statistics, can
sleep and they often also implicitly assume that the rtnl is
held around their invocation. This is almost always true now
except when reading from sysfs:

  BUG: sleeping function called from invalid context at kernel/mutex.c:280
  in_atomic(): 1, irqs_disabled(): 0, pid: 10450, name: head
  2 locks held by head/10450:
   #0:  (&buffer->mutex){+.+.+.}, at: [<c10ceb99>] sysfs_read_file+0x24/0xf4
   #1:  (dev_base_lock){++.?..}, at: [<c12844ee>] wireless_show+0x1a/0x4c
  Pid: 10450, comm: head Not tainted 2.6.32-rc3 #1
  Call Trace:
   [<c102301c>] __might_sleep+0xf0/0xf7
   [<c1324355>] mutex_lock_nested+0x1a/0x33
   [<f8cea53b>] wdev_lock+0xd/0xf [cfg80211]
   [<f8cea58f>] cfg80211_wireless_stats+0x45/0x12d [cfg80211]
   [<c13118d6>] get_wireless_stats+0x16/0x1c
   [<c12844fe>] wireless_show+0x2a/0x4c

Fix this by using the rtnl instead of dev_base_lock.

Reported-by: Miles Lane <miles.lane@gmail.com>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

be2net: Fix a bug in preparation of mcc wrb which was causing flash operation to fail

This patch fixes a bug that got introduced in commit 76998bc7.
During preparation of mcc wrb, req was being wrongly overwritten
and the flash operation was failing.

Signed-off-by: Ajit Khaparde <ajitk@serverengines.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

pcnet_cs: add cis of National Semicondoctor's multifunction pcmcia card

pcnet_cs,serial_cs:

add cis of National Semicondoctor's lan&modem mulitifunction pcmcia card,
NE2K, tamarack ethernet card,
and some serial card(COMpad2, COMpad4).

Signed-off-by: Ken Kawasaki <ken_kawasaki@spring.nifty.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: Support inclusion of <linux/socket.h> before <sys/socket.h>

The following user-space program fails to compile:

    #include <linux/socket.h>
    #include <sys/socket.h>
    int main() { return 0; }

The reason is that <linux/socket.h> tests __GLIBC__ to decide whether it
should define various structures and macros that are now defined for
user-space by <sys/socket.h>, but __GLIBC__ is not defined if no libc
headers have yet been included.

It seems safe to drop support for libc 5 now.

Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Bastian Blank <waldi@debian.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

pktgen: restore nanosec delays

Commit fd29cf72 (pktgen: convert to use ktime_t)
inadvertantly converted "delay" parameter from nanosec to microsec.

Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

pktgen: Fix multiqueue handling

It is not currently possible to instruct pktgen to use one selected tx queue.

When Robert added multiqueue support in commit 45b270f8, he added
an interval (queue_map_min, queue_map_max), and his code doesnt take
into account the case of min = max, to select one tx queue exactly.

I suspect a high performance setup on a eight txqueue device wants
to use exactly eight cpus, and assign one tx queue to each sender.

This patchs makes pktgen select the right tx queue, not the first one.

Also updates Documentation to reflect Robert changes.

Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Robert Olsson <robert.olsson@its.uu.se>
Signed-off-by: David S. Miller <davem@davemloft.net>

e1000e: swap max hw supported frame size between 82574 and 82583

There appears to have been a mixup in the max supported jumbo frame size
between 82574 and 82583 which ended up disabling jumbo frames on the 82574
as a result.  This patch swaps the two so that this issue is resolved.

This patch fixes http://bugzilla.kernel.org/show_bug.cgi?id=14261

Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

ixgbe: add support for 82599 based X520 10G Dual KX4 Mezz card

This patch adds device support for the 82599 based X520 10GbE
Dual Port KX4 Mezzanine card.

Signed-off-by: Don Skidmore<donald.c.skidmore@intel.com>
Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

ixgbe: add support for 82599 Combined Backplane

This patch will add support for the 82599 Dual port Backplane
device (0x10f8).  This device has the ability to link in serial (KR) and
parallel (KX4/KX) modes, depending on what the switch capabilities are in
the blade chassis.

Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

cnic: Fix NETDEV_UP event processing.

This fixes the problem of not handling the NETDEV_UP event properly
during hot-plug or modprobe of bnx2 after cnic.  The handling was
skipped by mistakenly using "else if" to check for the event.

Also update version to 2.0.1.

Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

uvesafb/connector: Disallow unpliviged users to send netlink packets

Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

pohmelfs/connector: Disallow unpliviged users to configure pohmelfs

Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

dst/connector: Disallow unpliviged users to configure dst

Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

dm/connector: Only process connector packages from privileged processes

Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

connector: Removed the destruct_data callback since it is always kfree_skb()

Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Acked-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

connector/dm: Fixed a compilation warning

Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Acked-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

connector: Provide the sender's credentials to the callback

Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Acked-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

connector: Keep the skb in cn_callback_data

Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Acked-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

e1000e/igb/ixgbe: Don't report an error if devices don't support AER

The only error returned by pci_{en,dis}able_pcie_error_reporting() is
-EIO which simply means that Advanced Error Reporting is not supported.
There is no need to report that, so remove the error check from e1000e,
igb and ixgbe.

Signed-off-by: Frans Pop <elendil@planet.nl>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: Fix wrong sizeof

Which is why I have always preferred sizeof(struct foo) over
sizeof(var).

Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: splice() from tcp to pipe should take into account O_NONBLOCK

tcp_splice_read() doesnt take into account socket's O_NONBLOCK flag

Before this patch :

splice(socket,0,pipe,0,128*1024,SPLICE_F_MOVE);
causes a random endless block (if pipe is full) and
splice(socket,0,pipe,0,128*1024,SPLICE_F_MOVE | SPLICE_F_NONBLOCK);
will return 0 immediately if the TCP buffer is empty.

User application has no way to instruct splice() that socket should be in blocking mode
but pipe in nonblock more.

Many projects cannot use splice(tcp -> pipe) because of this flaw.

http://git.samba.org/?p=samba.git;a=history;f=source3/lib/recvfile.c;h=ea0159642137390a0f7e57a123684e6e63e47581;hb=HEAD
http://lkml.indiana.edu/hypermail/linux/kernel/0807.2/0687.html

Linus introduced  SPLICE_F_NONBLOCK in commit 29e350944fdc2dfca102500790d8ad6d6ff4f69d
(splice: add SPLICE_F_NONBLOCK flag )

  It doesn't make the splice itself necessarily nonblocking (because the
  actual file descriptors that are spliced from/to may block unless they
  have the O_NONBLOCK flag set), but it makes the splice pipe operations
  nonblocking.

Linus intention was clear : let SPLICE_F_NONBLOCK control the splice pipe mode only

This patch instruct tcp_splice_read() to use the underlying file O_NONBLOCK
flag, as other socket operations do.

Users will then call :

splice(socket,0,pipe,0,128*1024,SPLICE_F_MOVE | SPLICE_F_NONBLOCK );

to block on data coming from socket (if file is in blocking mode),
and not block on pipe output (to avoid deadlock)

First version of this patch was submitted by Octavian Purdila

Reported-by: Volker Lendecke <vl@samba.org>
Reported-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Octavian Purdila <opurdila@ixiacom.com>
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Acked-by: Jens Axboe <jens.axboe@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: Use sk_mark for routing lookup in more places

This patch against v2.6.31 adds support for route lookup using sk_mark in some
more places. The benefits from this patch are the following.
First, SO_MARK option now has effect on UDP sockets too.
Second, ip_queue_xmit() and inet_sk_rebuild_header() could fail to do routing
lookup correctly if TCP sockets with SO_MARK were used.

Signed-off-by: Atis Elsts <atis@mikrotik.com>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>

sky2: irqname based on pci address

This is based on Michal Schmidt fix for skge.

Most network drivers request their IRQ when the interface is activated.
sky2 does it in ->probe() instead, because it can work with two-port
cards where the two net_devices use the same IRQ. This works fine most
of the time, except in some situations when the interface gets renamed.
Consider this example:

1. modprobe sky2
   The card is detected as eth0 and requests IRQ 17. Directory
   /proc/irq/17/eth0 is created.
2. There is an udev rule which says this interface should be called
   eth1, so udev renames eth0 -> eth1.
3. modprobe 8139too
   The Realtek card is detected as eth0. It will be using IRQ 17 too.
4. ip link set eth0 up
   Now 8139too requests IRQ 17.

The result is:
WARNING: at fs/proc/generic.c:590 proc_register ...
proc_dir_entry '17/eth0' already registered

The fix is for sky2 to name the irq based on the pci device, as is done
by some other devices DRM, infiniband, ...  ie. sky2@pci:0000:00:00

Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Reviewed-by: Michal Schmidt <mschmidt@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

skge: use unique IRQ name

Most network drivers request their IRQ when the interface is activated.
skge does it in ->probe() instead, because it can work with two-port
cards where the two net_devices use the same IRQ. This works fine most
of the time, except in some situations when the interface gets renamed.
Consider this example:

1. modprobe skge
   The card is detected as eth0 and requests IRQ 17. Directory
   /proc/irq/17/eth0 is created.
2. There is an udev rule which says this interface should be called
   eth1, so udev renames eth0 -> eth1.
3. modprobe 8139too
   The Realtek card is detected as eth0. It will be using IRQ 17 too.
4. ip link set eth0 up
   Now 8139too requests IRQ 17.

The result is:
WARNING: at fs/proc/generic.c:590 proc_register ...
proc_dir_entry '17/eth0' already registered
...
And "ls /proc/irq/17" shows two subdirectories, both called eth0.

Fix it by using a unique name for skge's IRQ, based on the PCI address.
The naming from the example then looks like this:
$ grep skge /proc/interrupts
 17:        169   IO-APIC-fasteoi   skge@pci:0000:00:0a.0, eth0

irqbalance daemon will have to be taught to recognize "skge@" as an
Ethernet interrupt. This will be a one-liner addition in classify.c. I
will send a patch to irqbalance if this change is accepted.

Signed-off-by: Michal Schmidt <mschmidt@redhat.com>
Acked-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

IPv4 TCP fails to send window scale option when window scale is zero

Acknowledge TCP window scale support by inserting the proper option in SYN/ACK
and SYN headers even if our window scale is zero.

This fixes the following observed behavior:

1. Client sends a SYN with TCP window scaling option and non zero window scale
value to a Linux box.
2. Linux box notes large receive window from client.
3. Linux decides on a zero value of window scale for its part.
4. Due to compare against requested window scale size option, Linux does not to
 send windows scale TCP option header on SYN/ACK at all.

With the following result:

Client box thinks TCP window scaling is not supported, since SYN/ACK had no
TCP window scale option, while Linux thinks that TCP window scaling is
supported (and scale might be non zero), since SYN had  TCP window scale
option and we have a mismatched idea between the client and server
regarding window sizes.

Probably it also fixes up the following bug (not observed in practice):

1. Linux box opens TCP connection to some server.
2. Linux decides on zero value of window scale.
3. Due to compare against computed window scale size option, Linux does
not to set windows scale TCP  option header on SYN.

With the expected result that the server OS does not use window scale option
due to not receiving such an option in the SYN headers, leading to suboptimal
performance.

Signed-off-by: Gilad Ben-Yossef <gilad@codefidence.com>
Signed-off-by: Ori Finkelman <ori@comsleep.com>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net/ipv4/tcp.c: fix min() type mismatch warning

net/ipv4/tcp.c: In function 'do_tcp_setsockopt':
net/ipv4/tcp.c:2050: warning: comparison of distinct pointer types lacks a cast

Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Kconfig: STRIP: Remove stale bits of STRIP help text

Remove references to dead web site mosquitonet.Stanford.EDU.

Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

NET: mkiss: Fix typo

This typo was introduced by 5793f4be23f0171b4999ca68a39a9157b44139f3 on
October 14, 2005 ...

Reported-by: Matti Aarnio <matti.aarnio@zmailer.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

tg3: Remove prev_vlan_tag from struct tx_ring_info

prev_vlan_tag field is not used.

Patch saves 512*8 bytes per tx queue ring on 64bit arches.

Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Acked-by: Matthew Carlson <mcarlson@broadcom.com>

move virtnet_remove to .devexit.text

The function virtnet_remove is used only wrapped by __devexit_p so define
it using __devexit.

Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Cc: David S. Miller <davem@davemloft.net>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Alex Williamson <alex.williamson@hp.com>
Cc: Mark McLoughlin <markmc@redhat.com>
Cc: netdev@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>

don't use __devexit_p to wrap sgiseeq_remove

The function sgiseeq_remove is defined using __exit, so don't use
__devexit_p but __exit_p to wrap it.

Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Cc: David S. Miller <davem@davemloft.net>
Cc: Wang Chen <wangchen@cn.fujitsu.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Patrick McHardy <kaber@trash.net>
Cc: netdev@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>

don't use __devexit_p to wrap meth_remove

The function meth_remove is defined using __exit, so don't use __devexit_p
but __exit_p to wrap it.

Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Cc: David S. Miller <davem@davemloft.net>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Patrick McHardy <kaber@trash.net>
Cc: Johannes Berg <johannes@sipsolutions.net>
Cc: netdev@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>

bonding: set primary param via sysfs

Primary module parameter passed to bonding is pernament. That means if you
release the primary slave and enslave it again, it becomes the primary slave
again. But if you set primary slave via sysfs, the primary slave is only set
once and it's not remembered in bond->params structure. Therefore the setting is
lost after releasing the primary slave. This simple one-liner fixes this.

Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge branch 'master' of git://git./linux/kernel/git/linville/wireless-2.6

pktgen: Fix delay handling

After last pktgen changes, delay handling is wrong.

pktgen actually sends packets at full line speed.

Fix is to update pkt_dev->next_tx even if spin() returns early,
so that next spin() calls have a chance to see a positive delay.

Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

ixgbe: correct the parameter description

ccffad25b5136958d4769ed6de5e87992dd9c65c changed parameters for function
ixgbe_update_uc_addr_list_generic but parameter description was not updated.
This patch corrects it.

Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

be2net: Workaround to fix a bug in Rx Completion processing.

vtp bit in RX completion descriptor could be wrongly set in
some skews of BladEngine.  Ignore this  bit if vtm is not set.
Resending because the previous patch was against net-next tree.
This patch is against the net-2.6 tree.

Signed-off-by: Ajit Khaparde <ajitk@serverengines.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

3c59x: Rework suspend and resume

As noticed by Alan Stern, there is still one issue with the driver:
we disable PCI IRQ on suspend, but other devices on the same IRQ
line might still need the IRQ enabled to suspend properly.

Nowadays, PCI core handles all power management work by itself, with
one condition though: if we use dev_pm_ops. So, rework the driver to
only quiesce 3c59x internal logic on suspend, while PCI core will
manage PCI device power state with IRQs disabled.

Suggested-by: Rafael J. Wysocki <rjw@sisk.pl>
Suggested-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Acked-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>

drivers/net: ks8851_mll ethernet network driver

This is the first registration of ks8851 network driver with
MLL(address/data multiplexed) interface.

Signed-off-by : David J. Choi <david.choi@micrel.com>

Signed-off-by: David S. Miller <davem@davemloft.net>

skge: Make sure both ports initialize correctly

If allocation of the second ports fails, make sure that hw->ports
 is not 2 otherwise we'll crash trying to access the second port.

This fix is copied from a similar fix in the sky2 driver (ca519274...),
but is untested, as I don't have a skge card.

Signed-off-by: Mike McCormack <mikem@ring3k.org>
Acked-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bcm63xx_enet: timeout off by one in do_mdio_op()

`while (limit-- >= 0)' reaches -2 after the loop upon timeout.

Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Acked-by: Maxime Bizon <mbizon@freebox.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>

qlge: Fix error exit for probe call.

Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

qlge: Protect reset recovery with rtnl_lock().

Move the call to rtnl_lock() to before the internal call to
ql_adapter_down()/ql_adapter_up().  This prevents collisions that can
happen when recovering from an asic error.

Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

qlge: Fix spin_lock warning.

Remove the unnecessary locking around the call to ql_adapter_reset().

Sep 25 08:17:29 localhost kernel:    SOFTIRQ-ON-W at:
Sep 25 08:17:29 localhost kernel:                         [<c0000000000a2964>] .lock_acquire+0x10c/0x158
Sep 25 08:17:29 localhost kernel:                         [<c0000000004542e0>] ._spin_lock+0x34/0x58
Sep 25 08:17:29 localhost kernel:                         [<d000000006723070>] .ql_adapter_down+0x40c/0x4a0 [qlge]
Sep 25 08:17:29 localhost kernel:                         [<d0000000067256d8>] .qlge_close+0x38/0x58 [qlge]
Sep 25 08:17:29 localhost kernel:                         [<c0000000003ada6c>] .dev_close+0xdc/0x118
Sep 25 08:17:29 localhost kernel:                         [<c0000000003adb48>] .rollback_registered+0xa0/0x158
Sep 25 08:17:29 localhost kernel:                         [<c0000000003adc50>] .unregister_netdevice+0x50/0x7c
Sep 25 08:17:29 localhost kernel:                         [<c0000000003adca0>] .unregister_netdev+0x24/0x40
Sep 25 08:17:29 localhost kernel:                         [<d00000000672e0c0>] .qlge_remove+0x28/0x64 [qlge]
Sep 25 08:17:29 localhost kernel:                         [<c000000000253fdc>] .pci_device_remove+0x50/0x90
Sep 25 08:17:29 localhost kernel:                         [<c0000000002f5434>] .__device_release_driver+0x94/0xf8
Sep 25 08:17:29 localhost kernel:                         [<c0000000002f5560>] .driver_detach+0xc8/0xfc
Sep 25 08:17:29 localhost kernel:                         [<c0000000002f3fd8>] .bus_remove_driver+0xb4/0x114
Sep 25 08:17:29 localhost kernel:                         [<c0000000002f5d4c>] .driver_unregister+0x80/0xa4
Sep 25 08:17:29 localhost kernel:                         [<c00000000025421c>] .pci_unregister_driver+0x50/0xc8
Sep 25 08:17:29 localhost kernel:                         [<d00000000672e044>] .qlge_exit+0x1c/0x34 [qlge]
Sep 25 08:17:29 localhost kernel:                         [<c0000000000ac8b0>] .SyS_delete_module+0x234/0x2d0
Sep 25 08:17:29 localhost kernel:                         [<c000000000008554>] syscall_exit+0x0/0x40
Sep 25 08:17:29 localhost kernel:    INITIAL USE at:

Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

qlge: Fix out of sync hardware semaphore.

ql_clear_routing_entries() takes/gives it's own hardware semaphore since
it is called from more than one place.  ql_route_initialize() should
make this call and THEN take it's own semaphore before doing it's work.

Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

qlge: Fix bad bit definitions.

Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

ixgbe: Remove ATR computation for UDP traffic

ATR support for UDP on 82599 needs to be redesigned, since the
current model doesn't make much sense.  The fallout from having
it in though is it causes all UDP traffic to still compute the
ATR hashes on transmit, which are useless.  This removal will
return upwards of 10% of relative computational overhead in
forwarding tests.

Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

ixgbe patch to provide NIC's tx/rx counters via ethtool

When LRO is enabled, the received packet and byte counters represent the
LRO'd packets, not the packets/bytes on the wire.  The Intel 82599 NIC has
registers that keep count of the physical packets.  Add these counters to
the ethtool stats.  The byte counters are 36-bit, but the high 4 bits were
being ignored in the 2.6.31 ixgbe driver:  Read those as well to allow
longer time between polling the stats to detect wraps.

Signed-off-by: Ben Greear <greearb@candelatech.com>
Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

ixgbe: Bump driver version number

A number of changes have gone in since the last version bump.  Bump
it to reflect the changes.

Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

ixgbe: Fix backplane flow control autoneg

Backplane flow control autonegotiation is currently broken for
ixgbe devices.  This patch fixes the flow control issues
with clause 37 autoneg.

Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

ixgbe: Fix disabling of relaxed ordering with Tx DCA

82599 has a different register offset for the Tx DCA control registers.
We disable relaxed ordering of the descriptor writebacks for Tx head
writeback, but didn't disable it properly for 82599.  However, this
shouldn't be a visible issue, since ixgbe doesn't use Tx head writeback.
This patch just makes sure we're not doing blind writes to offsets we
don't expect.

Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

ax25: Fix possible oops in ax25_make_new

In ax25_make_new, if kmemdup of digipeat returns an error, there would
be an oops in sk_free while calling sk_destruct, because sk_protinfo
is NULL at the moment; move sk->sk_destruct initialization after this.

BTW of reported-by: Bernard Pidoux F6BVP <f6bvp@free.fr>

Signed-off-by: Jarek Poplawski <jarkao2@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: restore tx timestamping for accelerated vlans

Since commit 9b22ea560957de1484e6b3e8538f7eef202e3596
( net: fix packet socket delivery in rx irq handler )

We lost rx timestamping of packets received on accelerated vlans.

Effect is that tcpdump on real dev can show strange timings, since it gets rx timestamps
too late (ie at skb dequeueing time, not at skb queueing time)

14:47:26.986871 IP 192.168.20.110 > 192.168.20.141: icmp 64: echo request seq 1
14:47:26.986786 IP 192.168.20.141 > 192.168.20.110: icmp 64: echo reply seq 1

14:47:27.986888 IP 192.168.20.110 > 192.168.20.141: icmp 64: echo request seq 2
14:47:27.986781 IP 192.168.20.141 > 192.168.20.110: icmp 64: echo reply seq 2

14:47:28.986896 IP 192.168.20.110 > 192.168.20.141: icmp 64: echo request seq 3
14:47:28.986780 IP 192.168.20.141 > 192.168.20.110: icmp 64: echo reply seq 3

Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Phonet: fix mutex imbalance

From: Rémi Denis-Courmont <remi.denis-courmont@nokia.com>

port_mutex was unlocked twice.

Signed-off-by: Rémi Denis-Courmont <remi.denis-courmont@nokia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

sit: fix off-by-one in ipip6_tunnel_get_prl

When requesting all prl entries (kprl.addr == INADDR_ANY) and there are
more prl entries than there is space passed from userspace, the existing
code would always copy cmax+1 entries, which is more than can be handled.

This patch makes the kernel copy only exactly cmax entries.

Signed-off-by: Sascha Hlusiak <contact@saschahlusiak.de>
Acked-By: Fred L. Templin <Fred.L.Templin@boeing.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: Fix sock_wfree() race

Commit 2b85a34e911bf483c27cfdd124aeb1605145dc80
(net: No more expensive sock_hold()/sock_put() on each tx)
opens a window in sock_wfree() where another cpu
might free the socket we are working on.

A fix is to call sk->sk_write_space(sk) while still
holding a reference on sk.

Reported-by: Jike Song <albcamus@gmail.com>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: Make setsockopt() optlen be unsigned.

This provides safety against negative optlen at the type
level instead of depending upon (sometimes non-trivial)
checks against this sprinkled all over the the place, in
each and every implementation.

Based upon work done by Arjan van de Ven and feedback
from Linus Torvalds.

Signed-off-by: David S. Miller <davem@davemloft.net>

ar9170: fix bug in iq-auto calibration value calculation

This patch fixes a embarrassing bug which was introduced by:
"[PATCH] ar9170: implement frequency calibration for one-stage/openfw"

The phy_data variable initialization has to done outside the for-loop
scope. This is because the for-loop uses u32 phy_data variable more
like a 4-byte field. But in each run only a single byte is calculated.
Therefore phy_data content needs to stay the same for at least 3 more
iterations, before the complete set can be uploaded.

Reported-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rt2x00: Thrustmaster FunAccess WIFI USB and rt73usb

Thrustmaster FunAccess WIFI USB works with rt73usb with little
modification of rt73usb.c.
Tested with version 2.3.0 of driver.

Signed-off-by: Michal Szalata <szalat@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mac80211_hwsim: Fix initial beacon timer configuration

mac80211_hwsim does not start transmitting Beacon frames when hostapd
is started for the first time and restarting hostapd fixes this. The
issue is caused by the config() handler not being able to start
beacon_timer when beacon interval is not yet known and
bss_info_changed() handler not starting the timer. This can be fixed by
making the bss_info_changed() update the timer.

Signed-off-by: Jouni Malinen <j@w1.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

b43: Always use block-I/O for the PIO data registers

On SDIO the PIO data register seems to be hardwired to LE. So
the MACCTL bit has no effect on the endianness.
So also use block-I/O for the last word of the packet. block-I/O is always LE.

Signed-off-by: Michael Buesch <mb@bu3sch.de>
Tested-by: Albert Herranz <albert_herranz@yahoo.es>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mac80211: Fix [re]association power saving issue on AP side

Consider the following step-by step:
1. A STA authenticates and associates with the AP and exchanges
traffic.
2. The STA reports to the AP that it is going to PS state.
3. Some time later the STA device goes to the stand-by mode (not only
its wi-fi card, but the device itself) and drops the association state
without sending a disassociation frame.
4. The STA device wakes up and begins authentication with an
Auth frame as it hasn't been authenticated/associated previously.

At the step 4 the AP "remembers" the STA and considers it is still in
the PS state, so the AP buffers frames, which it has to send to the STA.
But the STA isn't actually in the PS state and so it neither checks
TIM bits nor reports to the AP that it isn't power saving.
Because of that authentication/[re]association fails.

To fix authentication/[re]association stage of this issue, Auth, Assoc
Resp and Reassoc Resp frames are transmitted disregarding of STA's power
saving state.

N.B. This patch doesn't fix further data frame exchange after
authentication/[re]association. A patch in hostapd is required to fix
that.

Signed-off-by: Igor Perminov <igor.perminov@inbox.ru>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Merge branch 'master' of ssh:///linux/kernel/git/linville/wireless-2.6

sony-laptop: re-read the rfkill state when resuming from suspend

Without this, the hard-blocked state will be reported incorrectly if
the hardware switch is changed while the laptop is suspended.

Signed-off-by: Alan Jenkins <alan-jenkins@tuffmail.co.uk>
Tested-by: Norbert Preining <preining@logic.at>
Acked-by: Mattia Dongili <malattia@linux.it>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

sony-laptop: check for rfkill hard block at load time

"I recently (on a flight) I found out that when I boot with the hard-switch
activated, so turning off all wireless activity on my laptop, the state
is not correctly announced in /dev/rfkill (reading it with rfkill command,
or my own gnome applet)...

After turning off and on again the hard-switch the events were right."

We can fix this by querying the firmware at load time and calling
rfkill_set_hw_state().

Signed-off-by: Alan Jenkins <alan-jenkins@tuffmail.co.uk>
Tested-by: Norbert Preining <preining@logic.at>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Mattia Dongili <malattia@linux.it>
CC: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>

wext: add back wireless/ dir in sysfs for cfg80211 interfaces

The move away from having drivers assign wireless handlers,
in favour of making cfg80211 assign them, broke the sysfs
registration (the wireless/ dir went missing) because the
handlers are now assigned only after registration, which is
too late.

Fix this by special-casing cfg80211-based devices, all
of which are required to have an ieee80211_ptr, in the
sysfs code, and also using get_wireless_stats() to have
the same values reported as in procfs.

Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Reported-by: Hugh Dickins <hugh.dickins@tiscali.co.uk>
Tested-by: Hugh Dickins <hugh.dickins@tiscali.co.uk>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

wext: Add bound checks for copy_from_user

The wireless extensions have a copy_from_user to a local stack
array "essid", but both me and gcc have failed to find where
the bounds for this copy are located in the code.

This patch adds some basic sanity checks for the copy length
to make sure that we don't overflow the stack buffer.

Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Cc: linux-wireless@vger.kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mac80211: improve/fix mlme messages

It's useful to know the MAC address when being
disassociated; fix a typo (missing colon) and
move some messages so we get them only when they
are actually taking effect.

Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

cfg80211: always get BSS

Multiple problems were reported due to interaction
between wpa_supplicant and the wext compat code in
cfg80211, which appear to be due to it not getting
any bss pointer here when wpa_supplicant sets all
parameters -- do that now. We should still get the
bss after doing an extra scan, but that appears to
increase the time we need for connecting enough to
sometimes cause timeouts.

Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Tested-by: Hin-Tak Leung <hintak.leung@gmail.com>,
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwlwifi: fix 3945 ucode info retrieval after failure

When hardware or uCode problem occurs driver captures significant
information from device to enable debugging. The format of this information
is different between 3945 and 4965 and later devices, yet currently the
3945 uses the 4965 and later format. Fix this by adding a new library call
that is initialized to the correct formatting routine based on device.

This moves the iwlagn event and error log handling back to iwl-agn.c to
make it part of iwlagn module.

Also remove the 3945 sysfs file that triggers dump of event log - there is
already a debugfs file that can do it for all drivers.

Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwlwifi: fix memory leak in command queue handling

Also free the array of command pointers and meta data of each
command buffer when command queue is freed.

Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwlwifi: fix debugfs buffer handling

We keep track of where to write into a buffer by keeping a count of how
much has been written so far. When writing to the buffer we thus take the
buffer pointer and adding the count of what has been written so far.
Keeping track of what has been written so far is done by incrementing
this number every time something is written to the buffer with how much has
been written at that time.

Currently this number is incremented incorrectly when using the
"hex_dump_to_buffer" call to add data to the buffer. Fix this by only
adding what has been added to the buffer in that call instead of what has
been added since beginning of buffer.

Issue was discovered and discussed during testing of
https://bugzilla.redhat.com/show_bug.cgi?id=464598 .

When a user views any of these files they will see something like:

[  179.355202] ------------[ cut here ]------------
[  179.355209] WARNING: at ../lib/vsprintf.c:989 vsnprintf+0x5ec/0x5f0()
[  179.355212] Hardware name: VGN-Z540N
[  179.355213] Modules linked in: i915 drm i2c_algo_bit i2c_core ipv6 acpi_cpufreq cpufreq_userspace cpufreq_powersave cpufreq_ondemand cpufreq_conservative cpufreq_stats freq_table container sbs sbshc arc4 ecb iwlagn iwlcore joydev led_class mac80211 af_packet pcmcia psmouse sony_laptop cfg80211 iTCO_wdt iTCO_vendor_support pcspkr serio_raw rfkill intel_agp video output tpm_infineon tpm tpm_bios button battery yenta_socket rsrc_nonstatic pcmcia_core processor ac evdev ext3 jbd mbcache sr_mod sg cdrom sd_mod ahci libata scsi_mod ehci_hcd uhci_hcd usbcore thermal fan thermal_sys
[  179.355262] Pid: 5449, comm: cat Not tainted 2.6.31-wl-54419-ge881071 #62
[  179.355264] Call Trace:
[  179.355267]  [<ffffffff811ad14c>] ? vsnprintf+0x5ec/0x5f0
[  179.355271]  [<ffffffff81041348>] warn_slowpath_common+0x78/0xd0
[  179.355275]  [<ffffffff810413af>] warn_slowpath_null+0xf/0x20
[  179.355277]  [<ffffffff811ad14c>] vsnprintf+0x5ec/0x5f0
[  179.355280]  [<ffffffff811ad23d>] ? scnprintf+0x5d/0x80
[  179.355283]  [<ffffffff811ad23d>] scnprintf+0x5d/0x80
[  179.355286]  [<ffffffff811aed29>] ? hex_dump_to_buffer+0x189/0x340
[  179.355290]  [<ffffffff810e91d7>] ? __kmalloc+0x207/0x260
[  179.355303]  [<ffffffffa02a02f8>] iwl_dbgfs_nvm_read+0xe8/0x220 [iwlcore]
[  179.355306]  [<ffffffff811a9b62>] ? __up_read+0x92/0xb0
[  179.355310]  [<ffffffff810f0988>] vfs_read+0xc8/0x1a0
[  179.355313]  [<ffffffff810f0b50>] sys_read+0x50/0x90
[  179.355316]  [<ffffffff8100bd6b>] system_call_fastpath+0x16/0x1b
[  179.355319] ---[ end trace 2383d0d5e0752ca0 ]---

Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

cfg80211: don't set privacy w/o key

When wpa_supplicant is used to connect to open networks,
it causes the wdev->wext.keys to point to key memory, but
that key memory is all empty. Only use privacy when there
is a default key to be used.

Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Tested-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Tested-by: Kalle Valo <kalle.valo@iki.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

cfg80211: wext: don't display BSSID unless associated

Currently, cfg80211's SIOCGIWAP implementation returns
the BSSID that the user set, even if the connection has
since been dropped due to other changes. It only should
return the current BSSID when actually connected.

Also do a small code cleanup.

Reported-by: Thomas H. Guenther <thomas.h.guenther@intel.com>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Tested-by: Thomas H. Guenther <thomas.h.guenther@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

net: Add explicit bound checks in net/socket.c

The sys_socketcall() function has a very clever system for the copy
size of its arguments. Unfortunately, gcc cannot deal with this in
terms of proving that the copy_from_user() is then always in bounds.
This is the last (well 9th of this series, but last in the kernel) such
case around.

With this patch, we can turn on code to make having the boundary provably
right for the whole kernel, and detect introduction of new security
accidents of this type early on.

Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bridge: Fix double-free in br_add_if.

There is a potential double-kfree in net/bridge/br_if.c.  If br_fdb_insert
fails, then the kobject is put back (which calls kfree due to the kobject
release), and then kfree is called again on the net_bridge_port.  This
patch fixes the crash.

Thanks to Stephen Hemminger for the one-line fix.

Signed-off-by: Jeff Hansen <x@jeffhansen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

isdn: fix netjet/isdnhdlc build errors

Commit cb3824bade2549d7ad059d5802da43312540fdee didn't fix this problem.

Fix build errors in netjet, using isdnhdlc module:

drivers/built-in.o: In function `mode_tiger':
netjet.c:(.text+0x1ca0c7): undefined reference to `isdnhdlc_rcv_init'
netjet.c:(.text+0x1ca0d4): undefined reference to `isdnhdlc_out_init'
drivers/built-in.o: In function `fill_dma':
netjet.c:(.text+0x1ca2bd): undefined reference to `isdnhdlc_encode'
drivers/built-in.o: In function `read_dma':
netjet.c:(.text+0x1ca614): undefined reference to `isdnhdlc_decode'
drivers/built-in.o: In function `nj_irq':
netjet.c:(.text+0x1cb07a): undefined reference to `isdnhdlc_encode'

drivers/built-in.o: In function `isdnhdlc_decode':
(.text+0x1c2088): undefined reference to `crc_ccitt_table'
drivers/built-in.o: In function `isdnhdlc_encode':
(.text+0x1c2339): undefined reference to `crc_ccitt_table'

Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

atm: dereference of he_dev->rbps_virt in he_init_group()

The prefix decrement causes a very long loop if pci_pool_alloc() failed
in the first iteration. Also I swapped rbps and rbpl arguments.

Reported-by: Juha Leppanen <juha_motorsportcom@luukku.com>
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

ax25: Add missing dev_put in ax25_setsockopt

ax25_setsockopt SO_BINDTODEVICE is missing a dev_put call in case of
success.  Re-order code to fix this bug.  While at it also reformat two
lines of code to comply with the Linux coding style.

Initial patch by Jarek Poplawski <jarkao2@gmail.com>.

Reported-by: Bernard Pidoux F6BVP <f6bvp@free.fr>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Revert "sit: stateless autoconf for isatap"

This reverts commit 645069299a1c7358cf7330afe293f07552f11a5d.

While the code does not actually break anything, it does not completely follow
RFC5214 yet. After talking back with Fred L. Templin, I agree that completing the
ISATAP specific RS/RA code, would pollute the kernel a lot with code that is better
implemented in userspace.

The kernel should not send RS packages for ISATAP at all.

Signed-off-by: Sascha Hlusiak <contact@saschahlusiak.de>
Acked-by: Fred L. Templin <Fred.L.Templin@boeing.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: fix double skb free in dcbnl

netlink_unicast() calls kfree_skb even in the error case.

dcbnl calls netlink_unicast() which when it fails free's the
skb and returns an error value.  dcbnl is free'ing the skb
again when this error occurs.  This patch removes the double
free.

Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: fix nlmsg len size for skb when error bit is set.

Currently, the nlmsg->len field is not set correctly in  netlink_ack()
for ack messages that include the nlmsg of the error frame.  This
corrects the length field passed to __nlmsg_put to use the correct
payload size.

Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: fix vlan_get_size to include vlan_flags size

Fix vlan_get_size to include vlan->flags.  Currently, the
size of the vlan flags is not included in the nlmsg size.

Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

e1000: cleanup unused prototype

The function e1000_enable_tx_pkt_filtering() was removed in
a previous cleanup patch.  this removes the no longer used
prototype.

Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

e1000: fix namespacecheck warnings

a couple of functions needed to be removed/declared static

Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

e1000: drop unused functionality for eeprom write/read

eerd and eewr don't exist on pre PCIe devices

Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

e1000: updated whitespace and comments

A large whitespace change to e1000_hw.[ch] in order to update it to kernel coding
style (by running lindent).  Updated function header comments into kdoc style.

Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

e1000: drop redunant line of code, cleanup

adapter was being assigned twice, also clarified variable name and unwrapped
line.

Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

e1000: remove races when changing mtu

this patch fixes a bug that occurs when routing packets and simultaneously
changing the mtu.  the rx_buffer_len variable is used during the rx cleanup
and if that changes on the fly without stopping traffic bad things happen

Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

e1000: two workarounds were incomplete, fix them

1) 82544 does not need last_tx_tso workaround, it interferes with the 82544
workaround too
2) 82544 hang workaround was using the address of the page struct instead of
the physical address as its "workaround decider" not sure how that ever worked

Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>