Devin Heitmueller [Wed, 15 Jul 2009 03:37:22 +0000 (00:37 -0300)]
V4L/DVB (12263): em28xx: set demod profile for Pinnacle Hybrid Pro 320e
The Pinnacle Hybrid Pro 320e was missing a demod config for the xc3028, which
is required for digital tuning to work properly. Add the missing profile.
Thanks to Andreas Lunderhage for testing patches and providing a remote debug
environment.
Cc: Andreas Lunderhage <lunderhage@home.se>
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Devin Heitmueller [Wed, 15 Jul 2009 03:35:47 +0000 (00:35 -0300)]
V4L/DVB (12262): em28xx: Make sure the tuner is initialized if generic empia USB id was used
In cases where the device has a generic Empia USB ID, the call in the
precard setup phase did not set the tuner GPIO. As a result, the tuner may
not be taken out of reset before attempting initialization in the analog
driver.
This problem was not seen before with the EVGA inDtube, since that particular
board has the analog GPIO setup to include taking the tuner out of reset.
Thanks to Andreas Lunderhage for testing patches and providing a remote debug
environment for the Pinnacle 320e.
Cc: Andreas Lunderhage <lunderhage@home.se>
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Devin Heitmueller [Thu, 9 Jul 2009 01:18:15 +0000 (22:18 -0300)]
V4L/DVB (12261): em28xx: set GPIO properly for Pinnacle Hybrid Pro analog support
Set the GPIO properly for the analog side of the Pinnacle Hybrid Pro, or else
the emp202 doesn't get detected properly.
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Devin Heitmueller [Thu, 9 Jul 2009 00:51:35 +0000 (21:51 -0300)]
V4L/DVB (12260): em28xx: make support work for the Pinnacle Hybrid Pro (eb1a:2881)
Setup the GPIOs properly and enable support for the DVB side of the Pinnacle
Hybrid Pro USB stick.
Thanks to Andreas Lunderhage for testing patches and providing a remote debug
environment.
Cc: Andreas Lunderhage <lunderhage@home.se>
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Devin Heitmueller [Sun, 12 Jul 2009 21:44:19 +0000 (18:44 -0300)]
V4L/DVB (12258): em28xx: fix typo in mt352 init sequence for Terratec Cinergy T XS USB
Andy walls pointed out that we were passing 0x5d to the TUNER_GO register,
instead of 0x01. Set the register properly (note the code did still work with
the incorrect value, so this does not address a regression).
Thanks to Andy Walls for noticing the issue.
Cc: Andy Walls <awalls@radix.net>
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Devin Heitmueller [Sun, 12 Jul 2009 20:51:12 +0000 (17:51 -0300)]
V4L/DVB (12257): em28xx: make tuning work for Terratec Cinergy T XS USB (mt352 variant)
The Terratec Cinergy T XS USB can have either a zl10353 or an mt352. Add
support for the MT352 variant.
Thanks to Jelle de Jong for providing a unit to test/debug with.
Cc: Jelle de Jong <jelledejong@powercraft.nl>
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Mauro Carvalho Chehab [Wed, 15 Jul 2009 00:08:22 +0000 (21:08 -0300)]
V4L/DVB (12245): em28xx: add support for mt9m001 webcams
Thanks to Wally <wally@voosen.eu> for bringing the issue and helping
with the tests.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Mauro Carvalho Chehab [Tue, 14 Jul 2009 15:33:25 +0000 (12:33 -0300)]
V4L/DVB (12244): em28xx: adjust vinmode/vinctl based on the stream input format
Depending on the video input format, vinmode/vinctl needs adjustments.
For TV, this is not relevant, since the supported decoders output data
at the same format. However, webcam sensors may have different formats,
so, this needs to be adjusted based on the device.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Mauro Carvalho Chehab [Tue, 14 Jul 2009 06:18:39 +0000 (03:18 -0300)]
V4L/DVB (12243): em28xx: allow specifying sensor xtal frequency
In order to properly estimate fps, mt9v011 sensor driver needs to know
what is the used frequency on the sensor cristal. Adds the proper fields
and initialization code for specifying the cristal frequency.
Also, based on experimentation, it was noticed that the Silvercrest is
outputing data at 7 fps. This means that it should be using a 6.3 MHz
cristal. This information needs to be double checked later, by opening
the device. Anyway, by using this value for xtal, at least now we have
the correct fps report.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Mauro Carvalho Chehab [Tue, 14 Jul 2009 06:14:21 +0000 (03:14 -0300)]
V4L/DVB (12242): mt9v011: implement core->s_config to allow adjusting xtal frequency
Since frames per second is a function of cristal frequency, and this is
device-specific, add a function that allows adjusting it, via
subdev->core->s_config callback.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Mauro Carvalho Chehab [Tue, 14 Jul 2009 05:39:19 +0000 (02:39 -0300)]
V4L/DVB (12241): mt9v011: Fix vstart
vstart calculus were wrong. Fix it.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Mauro Carvalho Chehab [Tue, 14 Jul 2009 05:38:18 +0000 (02:38 -0300)]
V4L/DVB (12240): mt9v011: add a function to calculate frames per second rate
It is possible to adjust the fps rate by changing some register values.
This is function of the connected Xtal at the camera sensor, being a 27
MHz cristal needed, in order to support 640x480 at 30 fps.
For now, it will only calculate the values for fps. Later patches may
introduce V4L2 ioctls, to allow frequency rate adjustments.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Mauro Carvalho Chehab [Mon, 13 Jul 2009 23:15:02 +0000 (20:15 -0300)]
V4L/DVB (12239): em28xx: fix webcam scaling
While trying to fix an mt9v001 webcam, I noticed that HSCALE/VSCALE do
work with em28xx + webcam. The issue is that the scaling setup depends
on the number of visible rows/cols of the input image.
With mt9v011 (Silvercrest), the resolution is 640x480. So, the scaling
is different from a normal TV image (720x480 on NTSC). This were causing
a wrong scaling and a previous patch disabled scaling.
As each sensor have their different resolution setting, the xres/yres
should be adjusted accordingly with the input sensor.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Mauro Carvalho Chehab [Mon, 13 Jul 2009 04:28:21 +0000 (01:28 -0300)]
V4L/DVB (12238): em28xx: call sensor detection code for all webcam entries
With the previous approach, autodetection were working only for the two
generic entries (em275x and em2820 unknown ones). So, if someone would
try to force probing an specific device, the code would not properly run
the autodetection code.
With the new approach, the sensor autodetection will be run not only for
the two generic entries, but also do webcam specific ones.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Mauro Carvalho Chehab [Mon, 13 Jul 2009 04:03:37 +0000 (01:03 -0300)]
V4L/DVB (12237): mt9v011: implement VIDIOC_QUERYCTRL
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Mauro Carvalho Chehab [Sun, 12 Jul 2009 14:04:15 +0000 (11:04 -0300)]
V4L/DVB (12236): em28xx: stop abusing of board->decoder for sensor information
Instead of using em28xx board decoder field for storing sensor information,
let's use instead a separate field for it.
Also, as sensors are currently autodetected, there's no need of having
it at the boards description. So, move it to the main em28xx struct.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Mauro Carvalho Chehab [Sun, 12 Jul 2009 13:56:21 +0000 (10:56 -0300)]
V4L/DVB (12235): em28xx: detects sensors also with the generic em2750/2750 entry
Webcams in general don't have eeprom. So, the sensor hint code should be
called to properly detect what sensor is inside.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Mauro Carvalho Chehab [Sun, 12 Jul 2009 13:26:36 +0000 (10:26 -0300)]
V4L/DVB (12234): em28xx-cards: use is_webcam flag for devices that are known to be webcams
By having the webcam devices marked as such, it will help the em28xx
driver to do the right thing on those devices.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Mauro Carvalho Chehab [Sun, 12 Jul 2009 13:23:23 +0000 (10:23 -0300)]
V4L/DVB (12233): em28xx: rename is_27xx to is_webcam
Just renames the flag, to use a clearer name. Later patches will use
this flag to properly set some drivers behaviors for webcams.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Erik Andrén [Wed, 8 Jul 2009 17:47:16 +0000 (14:47 -0300)]
V4L/DVB (12224): gspca - m5602-s5k4aa: Remove erroneous register writes
A couple of erroneous register writes snuck in that made the image go haywire. Remove these.
Many thanks to Grégory Lardière for finding this out
Signed-off-by: Erik Andrén <erik.andren@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Erik Andrén [Wed, 1 Jul 2009 05:56:44 +0000 (02:56 -0300)]
V4L/DVB (12223): gspca - stv06xx-hdcs: Correct the pixelformat
Signed-off-by: Erik Andrén <erik.andren@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Erik Andrén [Wed, 24 Jun 2009 07:30:56 +0000 (04:30 -0300)]
V4L/DVB (12222): gspca - stv06xx-hdcs: Fix sensor sequence bug
All hdcs registers use bit 0 as a read/write flag and needs to be shifted one bit to the left. This wasn't accounted for when doing a sequence of writes.
Signed-off-by: Erik Andrén <erik.andren@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Erik Andrén [Tue, 23 Jun 2009 15:22:48 +0000 (12:22 -0300)]
V4L/DVB (12221): gspca - stv06xx-hdcs: Actually update the sensor state
Signed-off-by: Erik Andrén <erik.andren@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Linus Torvalds [Thu, 23 Jul 2009 02:32:59 +0000 (19:32 -0700)]
Linux 2.6.31-rc4
Linus Torvalds [Wed, 22 Jul 2009 23:44:33 +0000 (16:44 -0700)]
Merge branch 'irq-fixes-for-linus' of git://git./linux/kernel/git/tip/linux-2.6-tip
* 'irq-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
genirq: Fix UP compile failure caused by irq_thread_check_affinity
Linus Torvalds [Wed, 22 Jul 2009 23:44:18 +0000 (16:44 -0700)]
Merge branch 'lockdep-for-linus' of git://git./linux/kernel/git/peterz/linux-2.6-lockdep
* 'lockdep-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/peterz/linux-2.6-lockdep:
lockdep: Fix lockdep annotation for pipe_double_lock()
Bruno Premont [Wed, 22 Jul 2009 20:22:32 +0000 (22:22 +0200)]
genirq: Fix UP compile failure caused by irq_thread_check_affinity
Since genirq: Delegate irq affinity setting to the irq thread
(
591d2fb02ea80472d846c0b8507007806bdd69cc) compilation with
CONFIG_SMP=n fails with following error:
/usr/src/linux-2.6/kernel/irq/manage.c:
In function 'irq_thread_check_affinity':
/usr/src/linux-2.6/kernel/irq/manage.c:475:
error: 'struct irq_desc' has no member named 'affinity'
make[4]: *** [kernel/irq/manage.o] Error 1
That commit adds a new function irq_thread_check_affinity() which
uses struct irq_desc.affinity which is only available for CONFIG_SMP=y.
Move that function under #ifdef CONFIG_SMP.
[ tglx@brownpaperbag: compile and boot tested on UP and SMP ]
Signed-off-by: Bruno Premont <bonbons@linux-vserver.org>
LKML-Reference: <
20090722222232.
2eb3e1c4@neptune.home>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Peter Zijlstra [Tue, 21 Jul 2009 08:09:23 +0000 (10:09 +0200)]
lockdep: Fix lockdep annotation for pipe_double_lock()
The presumed use of the pipe_double_lock() routine is to lock 2 locks in
a deadlock free way by ordering the locks by their address. However it
fails to keep the specified lock classes in order and explicitly
annotates a deadlock.
Rectify this.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Acked-by: Miklos Szeredi <mszeredi@suse.cz>
LKML-Reference: <
1248163763.15751.11098.camel@twins>
Linus Torvalds [Wed, 22 Jul 2009 18:41:56 +0000 (11:41 -0700)]
Merge branch 'perf-counters-for-linus' of git://git./linux/kernel/git/peterz/linux-2.6-perf
* 'perf-counters-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/peterz/linux-2.6-perf: (31 commits)
perf_counter tools: Give perf top inherit option
perf_counter tools: Fix vmlinux symbol generation breakage
perf_counter: Detect debugfs location
perf_counter: Add tracepoint support to perf list, perf stat
perf symbol: C++ demangling
perf: avoid structure size confusion by using a fixed size
perf_counter: Fix throttle/unthrottle event logging
perf_counter: Improve perf stat and perf record option parsing
perf_counter: PERF_SAMPLE_ID and inherited counters
perf_counter: Plug more stack leaks
perf: Fix stack data leak
perf_counter: Remove unused variables
perf_counter: Make call graph option consistent
perf_counter: Add perf record option to log addresses
perf_counter: Log vfork as a fork event
perf_counter: Synthesize VDSO mmap event
perf_counter: Make sure we dont leak kernel memory to userspace
perf_counter tools: Fix index boundary check
perf_counter: Fix the tracepoint channel to perfcounters
perf_counter, x86: Extend perf_counter Pentium M support
...
Linus Torvalds [Wed, 22 Jul 2009 17:12:18 +0000 (10:12 -0700)]
Merge branch 'core-fixes-for-linus-2' of git://git./linux/kernel/git/tip/linux-2.6-tip
* 'core-fixes-for-linus-2' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
softirq: introduce tasklet_hrtimer infrastructure
Linus Torvalds [Wed, 22 Jul 2009 17:11:47 +0000 (10:11 -0700)]
Merge branch 'timers-fixes-for-linus' of git://git./linux/kernel/git/tip/linux-2.6-tip
* 'timers-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
clocksource: Prevent NULL pointer dereference
timer: Avoid reading uninitialized data
Linus Torvalds [Wed, 22 Jul 2009 17:11:24 +0000 (10:11 -0700)]
Merge branch 'irq-fixes-for-linus' of git://git./linux/kernel/git/tip/linux-2.6-tip
* 'irq-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
genirq: Delegate irq affinity setting to the irq thread
Linus Torvalds [Wed, 22 Jul 2009 17:10:36 +0000 (10:10 -0700)]
Merge branch 'sched-fixes-for-linus' of git://git./linux/kernel/git/tip/linux-2.6-tip
* 'sched-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
sched: fix nr_uninterruptible accounting of frozen tasks really
sched: fix load average accounting vs. cpu hotplug
sched: Account for vruntime wrapping
Linus Torvalds [Wed, 22 Jul 2009 17:06:33 +0000 (10:06 -0700)]
Merge branch 'tj-block-for-linus' of git://git./linux/kernel/git/tj/misc
* 'tj-block-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/misc:
virtio_blk: mark virtio_blk with __refdata to kill spurious section mismatch
block: sysfs fix mismatched queue_var_{store,show} in 64bit kernel
ataflop: adjust NULL test
block: fix failfast merge testing in elv_rq_merge_ok()
z2ram: Small cleanup for z2ram.c
Linus Torvalds [Wed, 22 Jul 2009 17:05:00 +0000 (10:05 -0700)]
Merge branch 'for-linus' of git://git./linux/kernel/git/ryusuke/nilfs2
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ryusuke/nilfs2:
fs/Kconfig: move nilfs2 out
Linus Torvalds [Wed, 22 Jul 2009 16:50:18 +0000 (09:50 -0700)]
Merge git://git./linux/kernel/git/davem/ide-2.6
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/ide-2.6:
ide-tape: Don't leak kernel stack information
ide: fix memory leak when flush command is issued
Linus Torvalds [Wed, 22 Jul 2009 16:49:58 +0000 (09:49 -0700)]
Merge git://git./linux/kernel/git/davem/net-2.6
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (37 commits)
sky2: Avoid races in sky2_down
drivers/net/mlx4: Adjust constant
drivers/net: Move a dereference below a NULL test
drivers/net: Move a dereference below a NULL test
connector: maintainer/mail update.
USB host CDC Phonet network interface driver
macsonic, jazzsonic: fix oops on module unload
macsonic: move probe function to .devinit.text
can: switch carrier on if device was stopped while in bus-off state
can: restart device even if dev_alloc_skb() fails
can: sja1000: remove duplicated includes
New device ID for sc92031 [1088:2031]
3c589_cs: re-initialize the multicast in the tc589_reset
Fix error return for setsockopt(SO_TIMESTAMPING)
netxen: fix thermal check and shutdown
netxen: fix deadlock on dev close
netxen: fix context deletion sequence
net: Micrel KS8851 SPI network driver
tcp: Use correct peer adr when copying MD5 keys
tcp: Fix MD5 signature checking on IPv4 mapped sockets
...
Linus Torvalds [Wed, 22 Jul 2009 16:47:49 +0000 (09:47 -0700)]
Merge branch 'bugfixes' of git://git.linux-nfs.org/projects/trondmy/nfs-2.6
* 'bugfixes' of git://git.linux-nfs.org/projects/trondmy/nfs-2.6:
NFSv4: Fix a problem whereby a buggy server can oops the kernel
NFSv4: Fix an NFSv4 mount regression
NFSv4: Fix an Oops in nfs4_free_lock_state
Linus Torvalds [Wed, 22 Jul 2009 16:32:12 +0000 (09:32 -0700)]
Merge branch 'for-linus' of git://git./linux/kernel/git/tiwai/sound-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6:
ALSA: ctxfi: Swapped SURROUND-SIDE channels on emu20k2
ALSA: ca0106 - Fix the max capture buffer size
ALSA: hda - Fix pin-setup for Sony VAIO with STAC9872 codecs
ALSA: hda - Add quirk for Gateway T6834c laptop
ALSA: OSS sequencer should be initialized after snd_seq_system_client_init
ALSA: sound/isa: convert nested spin_lock_irqsave to spin_lock
ALSA: hda_codec: Check for invalid zero connections
Linus Torvalds [Wed, 22 Jul 2009 16:30:07 +0000 (09:30 -0700)]
Merge branch 'for-linus' of git://git./linux/kernel/git/jikos/hid
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid:
HID: Move dereferences below a NULL test
HID: hiddev, fix lock imbalance
Arjan van de Ven [Tue, 21 Jul 2009 07:55:05 +0000 (00:55 -0700)]
perf: fix stack data leak
the "reserved" field was not initialized to zero, resulting in 4 bytes
of stack data leaking to userspace....
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Acked-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Wed, 22 Jul 2009 16:26:13 +0000 (09:26 -0700)]
Merge branch 'linux-next' of git://git.infradead.org/ubi-2.6
* 'linux-next' of git://git.infradead.org/ubi-2.6:
UBI: fix bug in image sequence number handling
UBI: gluebi: initialize ubi_num field
Linus Torvalds [Wed, 22 Jul 2009 16:25:31 +0000 (09:25 -0700)]
Merge branch 'for-linus' of git://git./linux/kernel/git/dtor/input
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: atkbd - add force relese key quirk for Soltech TA12
Input: fix EVIOCGNAME/JSIOCGNAME regression
Input: atkbd - add forced release keys quirk for FSC Amilo Pi 3525
Input: pcspkr - switch driver to dev_pm_ops
Input: xpad - don't resend successfully sent outgoing requests
Input: wistron_btns - recognize Maxdata Pro 7000 notebooks
Mike Galbraith [Tue, 21 Jul 2009 08:30:36 +0000 (10:30 +0200)]
perf_counter tools: Give perf top inherit option
Currently, perf top -p only tracks the pid provided, which isn't very useful
for watching forky loads, so give it an inherit option.
Signed-off-by: Mike Galbraith <efault@gmx.de>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
LKML-Reference: <
1248165036.9795.10.camel@marge.simson.net>
Mike Galbraith [Mon, 20 Jul 2009 12:01:38 +0000 (14:01 +0200)]
perf_counter tools: Fix vmlinux symbol generation breakage
vmlinux meets the criteria for symbol adjustment, which breaks vmlinux generated symbols.
Fix this by exempting vmlinux. This is a bit fragile in that someone could change the
kernel dso's name, but currently that name is also hardwired.
Signed-off-by: Mike Galbraith <efault@gmx.de>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
LKML-Reference: <
1248091298.18702.18.camel@marge.simson.net>
Jason Baron [Tue, 21 Jul 2009 18:16:29 +0000 (14:16 -0400)]
perf_counter: Detect debugfs location
If "/sys/kernel/debug" is not a debugfs mount point, search for the debugfs
filesystem in /proc/mounts, but also allows the user to specify
'--debugfs-dir=blah' or set the environment variable: 'PERF_DEBUGFS_DIR'
Signed-off-by: Jason Baron <jbaron@redhat.com>
[ also made it probe "/debug" by default ]
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
LKML-Reference: <
20090721181629.GA3094@redhat.com>
Jason Baron [Tue, 21 Jul 2009 16:20:22 +0000 (12:20 -0400)]
perf_counter: Add tracepoint support to perf list, perf stat
Add support to 'perf list' and 'perf stat' for kernel tracepoints. The
implementation creates a 'for_each_subsystem' and 'for_each_event' for
easy iteration over the tracepoints.
Signed-off-by: Jason Baron <jbaron@redhat.com>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
LKML-Reference: <
426129bf9fcc8ee63bb094cf736e7316a7dcd77a.
1248190728.git.jbaron@redhat.com>
Arnaldo Carvalho de Melo [Mon, 20 Jul 2009 17:14:12 +0000 (14:14 -0300)]
perf symbol: C++ demangling
[acme@doppio ~]$ perf report -s comm,dso,symbol -C firefox -d /usr/lib64/xulrunner-1.9.1/libxul.so | grep :: | head
2.21% [.] nsDeque::Push(void*)
1.78% [.] GraphWalker::DoWalk(nsDeque&)
1.30% [.] GCGraphBuilder::AddNode(void*, nsCycleCollectionParticipant*)
1.27% [.] XPCWrappedNative::CallMethod(XPCCallContext&, XPCWrappedNative::CallMode)
1.18% [.] imgContainer::DrawFrameTo(gfxIImageFrame*, gfxIImageFrame*, nsRect&)
1.13% [.] nsDeque::PopFront()
1.11% [.] nsGlobalWindow::RunTimeout(nsTimeout*)
0.97% [.] nsXPConnect::Traverse(void*, nsCycleCollectionTraversalCallback&)
0.95% [.] nsJSEventListener::cycleCollection::Traverse(void*, nsCycleCollectionTraversalCallback&)
0.95% [.] nsCOMPtr_base::~nsCOMPtr_base()
[acme@doppio ~]$
Cc: Pekka Enberg <penberg@cs.helsinki.fi>
Cc: Vegard Nossum <vegard.nossum@gmail.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Frédéric Weisbecker <fweisbec@gmail.com>
Suggested-by: Clark Williams <williams@redhat.com>
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
LKML-Reference: <
20090720171412.GB10410@ghostprotocols.net>
Arjan van de Ven [Tue, 21 Jul 2009 05:54:26 +0000 (22:54 -0700)]
perf: avoid structure size confusion by using a fixed size
for some reason, this structure gets compiled as 36 bytes in some files
(the ones that alloacte it) but 40 bytes in others (the ones that use it).
The cause is an off_t type that gets a different size in different
compilation units for some yet-to-be-explained reason.
But the effect is disasterous; the size/offset members of the struct
are at different offsets, and result in mostly complete garbage.
The parser in perf is so robust that this all gets hidden, and after
skipping an certain amount of samples, it recovers.... so this bug
is not normally noticed.
.... except when you want every sample to be exact.
Fix this by just using an explicitly sized type.
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
LKML-Reference: <
4A655917.
9080504@linux.intel.com>
Anton Blanchard [Wed, 22 Jul 2009 13:05:46 +0000 (23:05 +1000)]
perf_counter: Fix throttle/unthrottle event logging
Right now we only print PERF_EVENT_THROTTLE + 1 (ie PERF_EVENT_UNTHROTTLE).
Fix this to print both a throttle and unthrottle event.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
LKML-Reference: <
20090722130546.GE9029@kryten>
Anton Blanchard [Wed, 22 Jul 2009 13:04:12 +0000 (23:04 +1000)]
perf_counter: Improve perf stat and perf record option parsing
perf stat and perf record currently look for all options on the command
line. This can lead to some confusion:
# perf stat ls -l
Error: unknown switch `l'
While we can work around this by adding '--' before the command, the git
option parsing code can stop at the first non option:
# perf stat ls -l
Performance counter stats for 'ls -l':
....
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
LKML-Reference: <
20090722130412.GD9029@kryten>
Peter Zijlstra [Tue, 21 Jul 2009 11:19:40 +0000 (13:19 +0200)]
perf_counter: PERF_SAMPLE_ID and inherited counters
Anton noted that for inherited counters the counter-id as provided by
PERF_SAMPLE_ID isn't mappable to the id found through PERF_RECORD_ID
because each inherited counter gets its own id.
His suggestion was to always return the parent counter id, since that
is the primary counter id as exposed. However, these inherited
counters have a unique identifier so that events like
PERF_EVENT_PERIOD and PERF_EVENT_THROTTLE can be specific about which
counter gets modified, which is important when trying to normalize the
sample streams.
This patch removes PERF_EVENT_PERIOD in favour of PERF_SAMPLE_PERIOD,
which is more useful anyway, since changing periods became a lot more
common than initially thought -- rendering PERF_EVENT_PERIOD the less
useful solution (also, PERF_SAMPLE_PERIOD reports the more accurate
value, since it reports the value used to trigger the overflow,
whereas PERF_EVENT_PERIOD simply reports the requested period changed,
which might only take effect on the next cycle).
This still leaves us PERF_EVENT_THROTTLE to consider, but since that
_should_ be a rare occurrence, and linking it to a primary id is the
most useful bit to diagnose the problem, we introduce a
PERF_SAMPLE_STREAM_ID, for those few cases where the full
reconstruction is important.
[Does change the ABI a little, but I see no other way out]
Suggested-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
LKML-Reference: <
1248095846.15751.8781.camel@twins>
Peter Zijlstra [Wed, 22 Jul 2009 09:13:50 +0000 (11:13 +0200)]
perf_counter: Plug more stack leaks
Per example of Arjan's patch, I went through and found a few more.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Arjan van de Ven [Tue, 21 Jul 2009 07:55:05 +0000 (00:55 -0700)]
perf: Fix stack data leak
the "reserved" field was not initialized to zero, resulting in 4 bytes
of stack data leaking to userspace....
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Peter Zijlstra [Wed, 22 Jul 2009 14:31:36 +0000 (16:31 +0200)]
perf_counter: Remove unused variables
Fix a gcc unused variables warning.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Peter Zijlstra [Wed, 22 Jul 2009 16:05:48 +0000 (18:05 +0200)]
Merge commit 'tip/perfcounters/core' into perf-counters-for-linus
Linus Torvalds [Wed, 22 Jul 2009 15:49:22 +0000 (08:49 -0700)]
fbmon: work around compiler bug in gcc-2.4.2
There's some odd bug in gcc-4.2 where it miscompiles a simple loop whent
he loop counter is of type 'unsigned char' and it should count to 128.
The compiler will incorrectly decide that a trivial loop like this:
unsigned char i, ...
for (i = 0; i < 128; i++) {
..
is endless, and will compile it to a single instruction that just
branches to itself.
This was triggered by the addition of '-fno-strict-overflow', and we
could play games with compiler versions and go back to '-fwrapv'
instead, but the trivial way to avoid it is to just make the loop
induction variable be an 'int' instead.
Thanks to Krzysztof Oledzki for reporting and testing and to Troy Moure
for digging through assembler differences and finding it.
Reported-and-tested-by: Krzysztof Oledzki <olel@ans.pl>
Found-by: Troy Moure <twmoure@szypr.net>
Gcc-bug-acked-by: Ian Lance Taylor <iant@google.com>
Cc: stable@kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Peter Zijlstra [Wed, 22 Jul 2009 12:18:35 +0000 (14:18 +0200)]
softirq: introduce tasklet_hrtimer infrastructure
commit
ca109491f (hrtimer: removing all ur callback modes) moved all
hrtimer callbacks into hard interrupt context when high resolution
timers are active. That breaks code which relied on the assumption
that the callback happens in softirq context.
Provide a generic infrastructure which combines tasklets and hrtimers
together to provide an in-softirq hrtimer experience.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: torvalds@linux-foundation.org
Cc: kaber@trash.net
Cc: David Miller <davem@davemloft.net>
LKML-Reference: <
1248265724.27058.1366.camel@twins>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Mike McCormack [Wed, 22 Jul 2009 03:57:56 +0000 (20:57 -0700)]
sky2: Avoid races in sky2_down
Reset rx chain before trying to drain it.
Shut interrupts off last, incase there's something to report.
Signed-off-by: Mike McCormack <mikem@ring3k.org>
Acked-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Michael Buesch [Sun, 19 Jul 2009 09:15:19 +0000 (09:15 +0000)]
ide-tape: Don't leak kernel stack information
Don't leak kernel stack information through uninitialized structure members.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Acked-by: Borislav Petkov <petkovbb@gmail.com>.
Signed-off-by: David S. Miller <davem@davemloft.net>
Maxime Bizon [Thu, 16 Jul 2009 06:32:52 +0000 (06:32 +0000)]
ide: fix memory leak when flush command is issued
I'm using ide on 2.6.30.1 with xfs filesystem. I noticed a kernel memory
leak after writing lots of data, the kmalloc-96 slab cache keeps
growing. It seems the struct ide_cmd kmalloced by idedisk_prepare_flush
is never kfreed.
Commit
a09485df9cda49fbde2766c86eb18a9cae585162 ("ide: move request
type specific code from ide_end_drive_cmd() to callers (v3)") and
f505d49ffd25ed062e76ffd17568d3937fcd338c ("ide: fix barriers support")
cause this regression, cmd->rq must now be set for ide_complete_cmd to
honor the IDE_TFLAG_DYN flag.
Signed-off-by: Maxime Bizon <mbizon@freebox.fr>
Acked-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Trond Myklebust [Tue, 21 Jul 2009 23:22:38 +0000 (19:22 -0400)]
NFSv4: Fix a problem whereby a buggy server can oops the kernel
We just had a case in which a buggy server occasionally returns the wrong
attributes during an OPEN call. While the client does catch this sort of
condition in nfs4_open_done(), and causes the nfs4_atomic_open() to return
-EISDIR, the logic in nfs_atomic_lookup() is broken, since it causes a
fallback to an ordinary lookup instead of just returning the error.
When the buggy server then returns a regular file for the fallback lookup,
the VFS allows the open, and bad things start to happen, since the open
file doesn't have any associated NFSv4 state.
The fix is firstly to return the EISDIR/ENOTDIR errors immediately, and
secondly to ensure that we are always careful when dereferencing the
nfs_open_context state pointer.
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Trond Myklebust [Tue, 21 Jul 2009 20:48:07 +0000 (16:48 -0400)]
NFSv4: Fix an NFSv4 mount regression
Commit
008f55d0e019943323c20a03493a2ba5672a4cc8 (nfs41: recover lease in
_nfs4_lookup_root) forces the state manager to always run on mount. This is
a bug in the case of NFSv4.0, which doesn't require us to send a
setclientid until we want to grab file state.
In any case, this is completely the wrong place to be doing state
management. Moving that code into nfs4_init_session...
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Trond Myklebust [Tue, 21 Jul 2009 20:47:46 +0000 (16:47 -0400)]
NFSv4: Fix an Oops in nfs4_free_lock_state
The oops http://www.kerneloops.org/raw.php?rawid=537858&msgid= appears to
be due to the nfs4_lock_state->ls_state field being uninitialised. This
happens if the call to nfs4_free_lock_state() is triggered at the end of
nfs4_get_lock_state().
The fix is to move the initialisation of ls_state into the allocator.
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Julia Lawall [Sun, 19 Jul 2009 06:09:25 +0000 (06:09 +0000)]
drivers/net/mlx4: Adjust constant
The values in the advertising field are typically ADVERTISED_xxx, not
SUPPORTED_xxx. Both SUPPORTED_10000baseT_Full and
ADVERTISED_1000baseT_Full have the same value.
The semantic match that finds this problem is as follows:
(http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@@
struct ethtool_cmd E;
@@
*E.advertising = SUPPORTED_10000baseT_Full
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Julia Lawall [Sun, 19 Jul 2009 05:26:35 +0000 (05:26 +0000)]
drivers/net: Move a dereference below a NULL test
If the NULL test is necessary, then the dereference should be moved below
the NULL test.
The semantic patch that makes this change is as follows:
(http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@@
type T;
expression E,E1;
identifier i,fld;
statement S;
@@
- T i = E->fld;
+ T i;
... when != E=E1
when != i
if (E == NULL||...) S
+ i = E->fld;
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Julia Lawall [Sun, 19 Jul 2009 06:13:04 +0000 (06:13 +0000)]
drivers/net: Move a dereference below a NULL test
If the NULL test is necessary, then the dereferences should be moved below
the NULL test.
The semantic patch that makes this change is as follows:
(http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@@
type T;
expression E,E1;
identifier i,fld;
statement S;
@@
- T i = E->fld;
+ T i;
... when != E=E1
when != i
BUG_ON (E == NULL||...);
+ i = E->fld;
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Evgeniy Polyakov [Tue, 21 Jul 2009 19:43:51 +0000 (12:43 -0700)]
connector: maintainer/mail update.
Signed-off-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rémi Denis-Courmont [Tue, 21 Jul 2009 01:58:35 +0000 (01:58 +0000)]
USB host CDC Phonet network interface driver
Many Nokia handsets support a Phonet interface to the cellular modem
via a vendor-specific USB interface. CDC Phonet follows the
Communications Device Class model, with one control interface, and
and a pair of inactive and active data alternative interface. The later
has two bulk endpoint, one per direction.
This was tested against Nokia E61, Nokia N95, and the existing Phonet
gadget function for the Linux composite USB gadget framework.
Signed-off-by: Rémi Denis-Courmont <remi.denis-courmont@nokia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Finn Thain [Tue, 21 Jul 2009 19:21:49 +0000 (12:21 -0700)]
macsonic, jazzsonic: fix oops on module unload
Set the driver data before using it. Fixes an oops when doing rmmod.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Uwe Kleine-König [Sat, 11 Jul 2009 20:52:48 +0000 (20:52 +0000)]
macsonic: move probe function to .devinit.text
A pointer to mac_sonic_probe is passed to the core via
platform_driver_register and so the function must not disappear when the
.init sections are discarded. Otherwise (if also having HOTPLUG=y)
unbinding and binding a device to the driver via sysfs will result in an
oops as does a device being registered late.
Various other functions that are called by mac_sonic_probe need to move
to .devinit.text, too.
An alternative to this patch is using platform_driver_probe instead of
platform_driver_register plus removing the pointer to the probe function
from the struct platform_driver.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Tested-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Takashi Iwai [Tue, 21 Jul 2009 17:03:22 +0000 (19:03 +0200)]
Merge branch 'fix/misc' into for-linus
* fix/misc:
ALSA: ca0106 - Fix the max capture buffer size
ALSA: OSS sequencer should be initialized after snd_seq_system_client_init
ALSA: sound/isa: convert nested spin_lock_irqsave to spin_lock
Takashi Iwai [Tue, 21 Jul 2009 17:03:20 +0000 (19:03 +0200)]
Merge branch 'fix/hda' into for-linus
* fix/hda:
ALSA: hda - Fix pin-setup for Sony VAIO with STAC9872 codecs
ALSA: hda - Add quirk for Gateway T6834c laptop
ALSA: hda_codec: Check for invalid zero connections
Takashi Iwai [Tue, 21 Jul 2009 17:03:19 +0000 (19:03 +0200)]
Merge branch 'fix/ctxfi' into for-linus
* fix/ctxfi:
ALSA: ctxfi: Swapped SURROUND-SIDE channels on emu20k2
Thomas Gleixner [Tue, 21 Jul 2009 09:09:39 +0000 (11:09 +0200)]
genirq: Delegate irq affinity setting to the irq thread
irq_set_thread_affinity() calls set_cpus_allowed_ptr() which might
sleep, but irq_set_thread_affinity() is called with desc->lock held
and can be called from hard interrupt context as well. The code has
another bug as it does not hold a ref on the task struct as required
by set_cpus_allowed_ptr().
Just set the IRQTF_AFFINITY bit in action->thread_flags. The next time
the thread runs it migrates itself. Solves all of the above problems
nicely.
Add kerneldoc to irq_set_thread_affinity() while at it.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
LKML-Reference: <new-submission>
Jerone Young [Tue, 21 Jul 2009 05:14:59 +0000 (22:14 -0700)]
Input: atkbd - add force relese key quirk for Soltech TA12
Netbooks based on the Soltech TA12 do not send a key release
for volume keys causing Linux to think the key is constantly
being pressed forever.
Added quirk data for forced release keys.
BugLink: https://bugs.launchpad.net//bugs/397499
Signed-off-by: Jerone Young <jerone.young@canonical.com>
Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Linus Torvalds [Mon, 20 Jul 2009 23:49:45 +0000 (16:49 -0700)]
Merge git://git./linux/kernel/git/sam/kbuild-fixes
* git://git.kernel.org/pub/scm/linux/kernel/git/sam/kbuild-fixes:
vmlinux.lds.h: restructure BSS linker script macros
kconfig: initialize the screen before using curses(3) functions
kconfig: variable argument lists needs `stdarg.h'
kbuild, deb-pkg: fix install scripts for posix sh
Linus Torvalds [Mon, 20 Jul 2009 23:48:31 +0000 (16:48 -0700)]
Merge branch 'for-linus' of git://git./linux/kernel/git/ericvh/v9fs
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ericvh/v9fs:
9p: Fix incorrect parameters to v9fs_file_readn.
9p: Possible regression in p9_client_stat
9p: default 9p transport module fix
Linus Torvalds [Mon, 20 Jul 2009 23:47:30 +0000 (16:47 -0700)]
Merge git://git./linux/kernel/git/sfrench/cifs-2.6
* git://git.kernel.org/pub/scm/linux/kernel/git/sfrench/cifs-2.6:
cifs: free nativeFileSystem field before allocating a new one
[CIFS] Distinguish posix opens and mkdirs from legacy mkdirs in stats
Linus Torvalds [Mon, 20 Jul 2009 23:46:49 +0000 (16:46 -0700)]
Merge branch 'for-linus' of git://git./linux/kernel/git/vapier/blackfin
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/vapier/blackfin: (21 commits)
Blackfin: define HARDIRQ_BITS again for now
arch/blackfin: Add kmalloc NULL tests
Blackfin: add CPLB entries for Core B on-chip L1 SRAM regions
Blackfin: work around anomaly
05000189
Blackfin: drop per-cpu loops_per_jiffy tracking
Blackfin: fix bugs in GPIO resume code
Blackfin: bf537-stamp: fix irq decl for AD7142
Blackfin: fix handling of IPEND in interrupt context save
Blackfin: drop duplicate runtime checking of anomaly
05000448
Blackfin: fix incomplete renaming of the bfin-twi-lcd driver
Blackfin: fix wrong CTS inversion
Blackfin: update handling of anomaly 364 (wrong rev id in BF527-0.1)
Blackfin: fix early_dma_memcpy() handling of busy channels
Blackfin: handle BF561 Core B memory regions better when SMP=n
Blackfin: fix miscompilation in lshrdi3
Blackfin: fix silent crash when no uClinux MTD filesystem exists
Blackfin: restore exception banner when dumping crash info
Blackfin: work around anomaly
05000281
Blackfin: update anomaly lists to match latest sheets/usage
Blackfin: drop dead flash_probe call
...
Nicolas Pitre [Sun, 19 Jul 2009 00:34:37 +0000 (20:34 -0400)]
mvsdio: fix handling of partial word at the end of PIO transfer
Standard data flow for MMC/SD/SDIO cards requires that the mvsdio
controller be set for big endian operation. This is causing problems
with buffers which length is not a multiple of 4 bytes as the last
partial word doesn't get shifted all the way and stored properly in
memory. Let's compensate for this.
Signed-off-by: Nicolas Pitre <nico@marvell.com>
CC: stable@kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Sonic Zhang [Mon, 20 Jul 2009 15:05:37 +0000 (16:05 +0100)]
blackfin: fix wrong CTS inversion
The Blackfin serial headers were inverting the CTS value leading to wrong
handling of the CTS line which broke CTS/RTS handling completely.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Alan Cox [Mon, 20 Jul 2009 15:05:27 +0000 (16:05 +0100)]
tty: fix chars_in_buffers
This function does not have an error return and returning an error is
instead interpreted as having a lot of pending bytes.
Reported by Jeff Harris who provided a list of some of the remaining
offenders.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Julia Lawall [Mon, 20 Jul 2009 15:05:07 +0000 (16:05 +0100)]
specialix.c: convert nested spin_lock_irqsave to spin_lock
If spin_lock_irqsave is called twice in a row with the same second
argument, the interrupt state at the point of the second call overwrites
the value saved by the first call. Indeed, the second call does not
need to save the interrupt state, so it is changed to a simple
spin_lock.
The semantic match that finds this problem is as follows:
(http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@@
expression lock1,lock2;
expression flags;
@@
*spin_lock_irqsave(lock1,flags)
... when != flags
*spin_lock_irqsave(lock2,flags)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Kay Sievers [Mon, 20 Jul 2009 15:04:55 +0000 (16:04 +0100)]
vc: create vcs(a) devices for consoles
The buffer for the consoles are unconditionally allocated at con_init()
time, which miss the creation of the vcs(a) devices.
Since 2.6.30 (commit
4995f8ef9d3aac72745e12419d7fbaa8d01b1d81, 'vcs:
hook sysfs devices into object lifetime instead of "binding"' to be
exact) these devices are no longer created at open() and removed on
close(), but controlled by the lifetime of the buffers.
Reported-by: Gerardo Exequiel Pozzi <vmlinuz386@yahoo.com.ar>
Tested-by: Gerardo Exequiel Pozzi <vmlinuz386@yahoo.com.ar>
Cc: stable@kernel.org
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Wolfgang Grandegger [Mon, 20 Jul 2009 04:06:41 +0000 (04:06 +0000)]
can: switch carrier on if device was stopped while in bus-off state
This patch fixes a problem when a device is stopped while in the
bus-off state. Then the carrier remains off forever.
Signed-off-by: Kurt Van Dijck <kurt.van.dijck@skynet.be>
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Wolfgang Grandegger [Mon, 20 Jul 2009 04:06:40 +0000 (04:06 +0000)]
can: restart device even if dev_alloc_skb() fails
If dev_alloc_skb() failed in can_restart(), the device was left behind
in the bus-off state. This patch restarts the device nevertheless.
Signed-off-by: Kurt Van Dijck <kurt.van.dijck@eia.be>
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Wolfgang Grandegger [Mon, 20 Jul 2009 04:06:39 +0000 (04:06 +0000)]
can: sja1000: remove duplicated includes
Remove duplicated #include('s) in
drivers/net/can/sja1000/sja1000.c
Signed-off-by: Huang Weiyi <weiyi.huang@gmail.com>
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Layton [Mon, 20 Jul 2009 17:40:52 +0000 (13:40 -0400)]
cifs: free nativeFileSystem field before allocating a new one
...otherwise, we'll leak this memory if we have to reconnect (e.g. after
network failure).
Signed-off-by: Jeff Layton <jlayton@redhat.com>
CC: Stable <stable@kernel.org>
Signed-off-by: Steve French <sfrench@us.ibm.com>
Cesar Eduardo Barros [Sun, 19 Jul 2009 08:03:32 +0000 (08:03 +0000)]
New device ID for sc92031 [1088:2031]
rain_maker@root-forum.org wrote:
> Hello cesar,
>
> In a recent thread in a german linux forum, a user reported his PIC
> NIC not being recognized by the kernel.
>
> Fortunately he provided enough information and I was able to help him
> and get the device working with the sc92031 driver.
>
> The device ID is [1088:2031] (Vendor is called "Microcomputer Systems
> (M) Son"), here is the respective thread in "ubuntuusers.de"
>
> http://forum.ubuntuusers.de/topic/lankarte-unter-xubuntu-wird-nicht-erkannt/
>
> (Although you might not speak german, the code provided will show
> you, that the device is actually working with your driver).
>
> It would be nice, if you include this new device ID to the
> sc92031-driver.
>
> Regards,
>
> Axel Köllhofer (aka Rain_Maker)
Cc: rain_maker@root-forum.org
Signed-off-by: Cesar Eduardo Barros <cesarb@cesarb.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ken Kawasaki [Sun, 19 Jul 2009 13:08:12 +0000 (13:08 +0000)]
3c589_cs: re-initialize the multicast in the tc589_reset
3c589_cs:
re-initialize the multicast in the tc589_reset,
and spin_lock the set_multicast_list function.
Signed-off-by: Ken Kawasaki <ken_kawasaki@spring.nifty.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rémi Denis-Courmont [Mon, 20 Jul 2009 00:47:04 +0000 (00:47 +0000)]
Fix error return for setsockopt(SO_TIMESTAMPING)
I guess it should be -EINVAL rather than EINVAL. I have not checked
when the bug came in. Perhaps a candidate for -stable?
Signed-off-by: Rémi Denis-Courmont <remi.denis-courmont@nokia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Dhananjay Phadke [Fri, 17 Jul 2009 15:27:08 +0000 (15:27 +0000)]
netxen: fix thermal check and shutdown
Check temperature for all PCI functions, that can allow
graceful shutdown of all interfaces on the overheated card.
Old code was only monitoring temperature for function 0 only.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Dhananjay Phadke [Fri, 17 Jul 2009 15:27:07 +0000 (15:27 +0000)]
netxen: fix deadlock on dev close
netxen: fix deadlock on dev close
The tx ring accounting fix in commit
cb2107be43d2fc5eadec58b92b
("netxen: fix tx ring accounting") introduced intermittent
deadlock when inteface is going down.
This was possibly combined effect of speculative tx pause,
calling netif_tx_lock instead of queue lock and unclean
synchronization with napi which could end up unmasking
interrupt.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Dhananjay Phadke [Fri, 17 Jul 2009 15:27:06 +0000 (15:27 +0000)]
netxen: fix context deletion sequence
o Use D3 reset context deletion for NX2031, it cleans up
more resources in the firmware.
o Release rx buffers after hardware context has been reset.
o Delete tx context after rx context, some firmware control
commands are sent on tx context, so it should be the last
to go.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ben Dooks [Thu, 16 Jul 2009 05:24:08 +0000 (05:24 +0000)]
net: Micrel KS8851 SPI network driver
Network driver for the SPI version of the Micrel KS8851
network chip.
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Frank Roth [Mon, 20 Jul 2009 15:00:14 +0000 (17:00 +0200)]
ALSA: ctxfi: Swapped SURROUND-SIDE channels on emu20k2
On Soundblaster X-FI Titanium with emu20k2 the SIDE and SURROUND
channels were swapped and wrong.
I double checked it with connector colors and creative soundblaster
windows drivers.
So I swapped them to the true order.
Now "speaker-test -c6" and "speaker-test -c8" are working fine.
Signed-off-by: Frank Roth <frashman@freenet.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
John Dykstra [Fri, 17 Jul 2009 09:23:22 +0000 (09:23 +0000)]
tcp: Use correct peer adr when copying MD5 keys
When the TCP connection handshake completes on the passive
side, a variety of state must be set up in the "child" sock,
including the key if MD5 authentication is being used. Fix TCP
for both address families to label the key with the peer's
destination address, rather than the address from the listening
sock, which is usually the wildcard.
Reported-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: John Dykstra <john.dykstra1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
John Dykstra [Thu, 16 Jul 2009 05:04:51 +0000 (05:04 +0000)]
tcp: Fix MD5 signature checking on IPv4 mapped sockets
Fix MD5 signature checking so that an IPv4 active open
to an IPv6 socket can succeed. In particular, use the
correct address family's signature generation function
for the SYN/ACK.
Reported-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: John Dykstra <john.dykstra1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Wan ZongShun [Thu, 16 Jul 2009 02:55:05 +0000 (02:55 +0000)]
Add mac driver for w90p910
Add mac driver support for evaluation board based on w90p910.
Signed-off-by: Wan ZongShun <mcuos.com@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
projects / GitHub / moto-9609 / android_kernel_motorola_exynos9610.git / log