mmc: core/mmci: restore pre/post_req behaviour

commit 64b12a68a9f74bb32d8efd7af1ad8a2ba02fc884
"mmc: core: fix prepared requests while doing bkops"
is fixing a bug in the wrong way. A bug in the MMCI
device driver is fixed by amending the MMC core.

Thinking about it: what the pre- and post-callbacks
are doing is to essentially map and unmap SG lists
for DMA transfers. Why would we not be able to do that
just because a BKOPS command is sent inbetween?
Having to unprepare/prepare the next asynchronous
request for DMA seems wrong.

Looking the backtrace in that commit we can see what
the real problem actually is:

mmci_data_irq() is calling mmci_dma_unmap() twice
which is goung to call arm_dma_unmap_sg() twice
and v7_dma_inv_range() twice for the same sglist
and that will crash.

This happens because a request is prepared, then
a BKOPS is sent. The IRQ completing the BKOPS command
goes through mmci_data_irq() and thinks that a DMA
operation has just been completed because
dma_inprogress() reports true. It then proceeds to
unmap the sglist.

But that was wrong! dma_inprogress() should NOT be
true because no DMA was actually in progress! We had
just prepared the sglist, and the DMA channel
dma_current has been configured, but NOT started!

Because of this, the sglist is already unmapped when
we get our actual data completion IRQ, and we are
unmapping the sglist once more, and we get this crash.

Therefore, we need to revert this solution pushing
the problem to the core and causing problems, and
instead augment the implementation such that
dma_inprogress() only reports true if some DMA has
actually been started.

After this we can keep the request prepared during the
BKOPS and we need not unprepare/reprepare it.

Fixes: 64b12a68a9f7 ("mmc: core: fix prepared requests while doing bkops")
Cc: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Tested-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

mmc: sunxi: Add more debug informations

Add a bit more debug messages that can be helpful when debugging the clock
setup.

Also fill the actual_clock field in struct mmc_host to report properly the
current frequency in debugfs.

Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Tested-by: Florian Vaussard <florian.vaussard@heig-vd.ch>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

mmc: sunxi: Add EMMC (MMC2) controller compatible

The MMC2 controller on the A64 is kind of a special beast.

While the general controller design is the same than the other MMC
controllers in the SoC, it also has a bunch of features and changes that
prevent it to be driven in the same way.

It has for example a different bus width limit, a different maximum
frequency, and, for some reason, the maximum buffer size of a DMA
descriptor.

Add a new compatible specifically for this controller.

Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Tested-by: Florian Vaussard <florian.vaussard@heig-vd.ch>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

mmc: sunxi: Mask DATA0 when updating the clock

The A64 MMC controllers need DATA0 to be masked while updating the clock,
otherwise any subsequent command will result in a timeout.

It's not really clear at this point what DATA0 is exactly, but this
behaviour is present in Allwinner's tree, and has been suggested by
Allwinner engineers as fixes for the timeout.

Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Tested-by: Florian Vaussard <florian.vaussard@heig-vd.ch>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

mmc: sunxi: Enable the new timings for the A64 MMC controllers

The A64 MMC controllers need to set a "new timings" bit when a new rate is
set.

The actual meaning of that bit is not clear yet, but not setting it leads
to some corner-case issues, like the CMD53 failing, which is used to
implement SDIO packet aggregation.

Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Tested-by: Florian Vaussard <florian.vaussard@heig-vd.ch>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

mmc: sunxi: Always set signal delay to 0 for A64

Experience have shown that the using the  autocalibration could severely
degrade the performances of the MMC bus.

Allwinner is using in its BSP a delay set to 0 for all the modes but HS400.
Remove the calibration code for now, and add comments to document our
findings.

Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Tested-by: Florian Vaussard <florian.vaussard@heig-vd.ch>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

mmc: sunxi: Gate the clock when rate is 0

The MMC core assumes that the code will gate the clock when the bus
frequency is set to 0, which we've been ignoring so far.

Handle that.

Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Tested-by: Florian Vaussard <florian.vaussard@heig-vd.ch>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

mmc: sunxi: Fix clock frequency change sequence

The SD specification documents that the clock frequency should only be
changed once gated (Section 3.2.3 - SD Clock Frequency Change Sequence).

The current code first modifies the parent clock, gates it and then
modifies the internal divider. This means that since the parent clock rate
might be changed, the bus clock might be changed as well before it is
gated, which breaks the specification.

Move the gating before the parent rate modification.

Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Tested-by: Florian Vaussard <florian.vaussard@heig-vd.ch>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

mmc: core: fix error path in mmc_host_alloc

Properly reverse everything if mmc_gpio_alloc(host) fails.

Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

mmc: core: simplify ida handling

ida handling can be simplified by switching to the ida_simple_
functions.

Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

mmc: sdhci-msm: Remove unnecessary comments of CDC init sequence

This removes CDC init sequence comments which are
not useful anyway.

Signed-off-by: Ritesh Harjani <riteshh@codeaurora.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

mmc: sdhci-msm: Remove platform_execute_tuning from sdhci_msm_ops

platform_execute_tuning should not really exist as it does not
do anything useful.

So remove this ops and directly plug sdhci_msm_execute_tuning
with mmc_host_ops.

Also in case of HS400 tuning clear SDHCI_HS400_TUNING flag once
HS400 related mode selection is done.

Signed-off-by: Ritesh Harjani <riteshh@codeaurora.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

mmc: core: Extend mmc_of_parse() to check for mmc-ddr-3_3v

When mmc_of_parse() finds the binding, it sets the mmc cap,
MMC_CAP_3_3V_DDR, which informs the core whether eMMC DDR at 3.3V I/O is
supported by the mmc host.

Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Tested-by: Jan Glauber <jglauber@cavium.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>

mmc: dt: Document binding for eMMC DDR 3.3V I/O voltage support

Cc: <devicetree@vger.kernel.org>
Cc: Rob Herring <robh@kernel.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Tested-by: Jan Glauber <jglauber@cavium.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Acked-by: Rob Herring <robh@kernel.org>

mmc: core: Invent MMC_CAP_3_3V_DDR

According the JEDEC specification an eMMC card supporting 1.8V vccq in DDR
mode should also be capable of 3.3V. However, it's been reported that some
mmc hosts supports 3.3V, but not 1.8V.

Currently the mmc core implements an error handling when the host fails to
set 1.8V for vccq, by falling back to 3.3V. Unfortunate, this seems to be
insufficient for some mmc hosts. To enable these to use eMMC DDR mode let's
invent a new mmc cap, MMC_CAP_3_3V_DDR, which tells whether they support
the eMMC 3.3V DDR mode.

In case MMC_CAP_3_3V_DDR is set, but not MMC_CAP_1_8V_DDR, let's change to
remain on the 3.3V, as it's the default voltage level for vccq, set by the
earlier power up sequence.

As this change introduces MMC_CAP_3_3V_DDR, let's take the opportunity to
do some re-formatting of the related defines in the header file.

Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Tested-by: Jan Glauber <jglauber@cavium.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>

mmc: core: Rename __mmc_set_signal_voltage() to mmc_set_signal_voltage()

Earlier the mmc_set_signal_voltage() existed, but since it has been renamed
to mmc_set_uhs_voltage(), we can now use that name instead.

Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Tested-by: Jan Glauber <jglauber@cavium.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>

mmc: core: Clarify usage of mmc_set_signal_voltage()

The mmc_set_signal_voltage() function is used for SD/SDIO when switching to
1.8V for UHS mode. To clarify this let's do the following changes.

- We are always providing MMC_SIGNAL_VOLTAGE_180 as the signal_voltage
  parameter to the function. Then, let's just remove the parameter as it
  serves no purpose.
- Rename the function to mmc_set_uhs_voltage().

Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Tested-by: Jan Glauber <jglauber@cavium.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>

mmc: core: Remove redundant code in mmc_set_signal_voltage()

The mmc_set_signal_voltage() function is used for SD/SDIO when switching to
1.8V for UHS mode. Therefore let's remove the redundant code dealing with
MMC_SIGNAL_VOLTAGE_330.

Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Tested-by: Jan Glauber <jglauber@cavium.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>

mmc: sh_mobile_sdhi: explain clock bindings

In the case of a single clock source, you don't need names. However,
if the controller has 2 clock sources, you need to name them correctly
so the driver can find the 2nd one. The 2nd clock is for the internal
card detect logic.

Signed-off-by: Chris Brandt <chris.brandt@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Rob Herring <robh@kernel.org>

mmc: sh_mobile_sdhi: add support for 2 clocks

Some controllers have 2 clock sources instead of 1. The 2nd clock
is for the internal card detect logic and must be enabled/disabled
along with the main core clock for proper operation.

Signed-off-by: Chris Brandt <chris.brandt@renesas.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>

mmc: meson: cleanup stray debug messages

Cleanup some debug prints that cause needless noise
during normal usage.

Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

mmc: block: stop passing around pointless return values

The mmc_blk_issue_rq() function is called in exactly one place
in queue.c and there the return value is ignored. So the
functions called from that function that also meticulously
return 0/1 do so for no good reason.

Error reporting on the asynchronous requests are done upward to
the block layer when the requests are eventually completed or
fail, which may happen during the flow of the mmc_blk_issue_*
functions directly (for "special commands") or later, when an
asynchronous read/write request is completed.

The issuing functions do not give rise to errors on their own,
and there is nothing to return back to the caller in queue.c.
Drop all return values and make the function return void.

Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

mmc: block: introduce new_areq and old_areq

Recycling the same variable in an x=x+1 fashion may seem
clever here but it makes the code terse and hard to follow
for humans. Introduce a new_areq and old_areq variable so
we see what is going on.

Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

mmc: block: inline command abortions

Setting rqc to NULL followed by a goto to cmd_abort is just a way
to do unconditional abort without starting any new command.
Inline the calls to mmc_blk_rw_cmd_abort() and return immediately
in those cases.

Add some comments to the code flow so it is clear that this is
where the asynchronous requests come back in and the result of
them gets handled.

Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

mmc: block: do not assign mq_rq when aborting command

The code in mmc_blk_issue_rq_rq() aborts a command if the request
is not properly aligned on large sectors. As part of the path
jumping out, it assigns the local variable mq_rq reflecting
a MMC queue request to the current MMC queue request, which is
confusing since the variable is not used after this jump.

Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

mmc: block: break out mmc_blk_rw_start_new()

As a step toward breaking apart the very complex function
mmc_blk_issue_rw_rq() we break out the code to start a new
request.

Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

mmc: block: break out mmc_blk_rw_cmd_abort()

As a first step toward breaking apart the very complex function
mmc_blk_issue_rw_rq() we break out the command abort code.
This code assumes "ret" is != 0 and then repeatedly hammers
blk_end_request() until the request to the block layer to end
the request succeeds.

Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

mmc: sdhci-s3c: use the bitops API for bit operation

Use the bitops API instead of shifting directly.

Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

mmc: sdhci-s3c: remove the sdhci-s3c-regs header file

Remove the sdhci-s3c-regs.h file.
Instead, it located those defined values into sdhci-s3c.c.

Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

mmc: tmio: discard obsolete SDIO irqs before enabling irqs

Before enabling SDIO irqs, clear the status bit, so we discard old and
stale interrupts. Needed to get two wireless cards working. Use the
newly introduced macro in all places.

Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

mmc: host: tmio: SDIO_STATUS_QUIRK is rather SDIO_STATUS_SETBITS

QUIRK sounds like there is something wrong, but actually there are just
some bits which need to be 1. Rename it to be more clear.

Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

mmc: host: tmio: refactor calls to sdio irq

tmio_mmc_sdio_irq() is not used as a seperate irq handler anymore, so we
can make it similar to the other irq helper functions, namely:

* only give the host as argument function which is what it really needs
* prefix function name with __

Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

mmc: pwrseq: add support for Marvell SD8787 chip

Allow power sequencing for the Marvell SD8787 Wifi/BT chip.
This can be abstracted to other chipsets if needed in the future.

Cc: Tony Lindgren <tony@atomide.com>
Cc: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Matt Ranostay <matt@ranostay.consulting>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

devicetree: document new marvell-8xxx and pwrseq-sd8787 options

Cc: Rob Herring <robh@kernel.org>
Cc: devicetree@vger.kernel.org
Signed-off-by: Matt Ranostay <matt@ranostay.consulting>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Rob Herring <robh@kernel.org>

mmc: host: tmio: disable clocks when unbinding

Create a helper function to disable clocks and use it in remove(), too.
Now, clk_summary in debugfs reports the clocks as disabled and
unprepared after unbinding.

Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

mmc: sdhci-msm: Provide enhanced_strobe mode feature support

This provides enhanced_strobe mode feature support in sdhci-msm
driver.

Signed-off-by: Ritesh Harjani <riteshh@codeaurora.org>
Tested-by: Jeremy McNicoll <jeremymc@redhat.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

mmc: sdhci-msm: Make HS400 tuning follow as per recommeneded HW sequence

During tuning execution for HS400 mode, HW sequence recommends
to select MCLK_SEL/2(0x3) in VENDOR_SPEC & sdhc msm clock at GCC
to be 400MHZ (nearest supported clk). Add this change in tuning
sequence during HS400 tuning.

Signed-off-by: Ritesh Harjani <riteshh@codeaurora.org>
Tested-by: Jeremy McNicoll <jeremymc@redhat.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

mmc: sdhci: Clear SDHCI_HS400_TUNING flag after platform_execute_tuning

Clear SDHCI_HS400_TUNING flag after platform_execute_tuning
so that platform_execute_tuning may use it if needed.

Signed-off-by: Ritesh Harjani <riteshh@codeaurora.org>
Tested-by: Jeremy McNicoll <jeremymc@redhat.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

mmc: sdhci-msm: configure CORE_CSR_CDC_DELAY_CFG to recommended value

Program CORE_CSR_CDC_DELAY_CFG for hardware recommended 1.25ns delay.
We may see data CRC errors if it's programmed for any other delay
value.

Signed-off-by: Subhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: Ritesh Harjani <riteshh@codeaurora.org>
Tested-by: Jeremy McNicoll <jeremymc@redhat.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

mmc: sdhci-msm: Reset vendor specific func register on probe

The vendor specific func register doesn't get reset when using the
software reset register. The various bootloader's could leave this
in an unknown state, hence reset this register to it's power on reset
value during probe.

Signed-off-by: Venkat Gopalakrishnan <venkatg@codeaurora.org>
Signed-off-by: Ritesh Harjani <riteshh@codeaurora.org>
Tested-by: Jeremy McNicoll <jeremymc@redhat.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

mmc: sdhci-msm: Factor out sdhci_msm_hs400

Factor out sdhci_msm_hs400 used for DLL calibration in HS400
modes. This function will be needed for enhanced_strobe as well.

Signed-off-by: Ritesh Harjani <riteshh@codeaurora.org>
Tested-by: Jeremy McNicoll <jeremymc@redhat.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

mmc: sdhci-msm: Factor out function to set/get msm clock rate

Factor out msm_set/get_clock_rate_for_bus_mode for it's later
use in changing the tuning sequence for selecting HS400
bus speed mode.

Signed-off-by: Ritesh Harjani <riteshh@codeaurora.org>
Tested-by: Jeremy McNicoll <jeremymc@redhat.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

mmc: sdhci-msm: Factor out sdhci_msm_hc_select_mode

This factors out sdhci_msm_hc_select_mode to later use
it during enhanced_strobe mode select.
It also further breaks sdhci_msm_hc_select_mode
into separate functions for configuring HS400 mode
or other modes.

Signed-off-by: Ritesh Harjani <riteshh@codeaurora.org>
Tested-by: Jeremy McNicoll <jeremymc@redhat.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

mmc: mxs-mmc: Implement CMD23 support

This patch implements support for multiblock transfers bounded
by SET_BLOCK_COUNT (CMD23) on the MXS MMC host driver.

Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

mmc: wbsd: safer check if dma_addr is valid DMA address

host->dma_addr can store a value that is not returned by the DMA API,
so it is safer to check if is a valid DMA address indirectly.

Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

mmc: sdhci-acpi: support deferred probe

With commit 67bf5156edc4 ("gpio / ACPI: fix returned error from
acpi_dev_gpio_irq_get()"), mmc_gpiod_request_cd() returns -EPROBE_DEFER if
GPIO is not ready when sdhci-acpi driver is probed, and sdhci-acpi driver
should be probed again later in this case.

This fixes an order issue when both GPIO and sdhci-acpi drivers are built
as modules.

CC: stable@vger.kernel.org # v4.9
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=177101
Tested-by: Jonas Aaberg <cja@gmx.net>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

mmc: core: Don't use extern declarations of public mmc functions

Using extern when declaring functions in the public header, core.h, is
redundant. Let's just remove the use of it.

Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>

mmc: core: Move public functions from host.h to private headers

A significant amount of functions are available through the public mmc
host.h header file. Let's slim down this public mmc interface, as to
prevent users from abusing it, by moving some of the functions to private
mmc host.h header file.

This change concentrates on moving the functions into private mmc headers,
following changes may continue with additional clean-ups.

Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>

mmc: core: Move public functions from card.h to private headers

A significant amount of functions and other definitions are available
through the public mmc card.h header file. Let's slim down this public mmc
interface, as to prevent users from abusing it, by moving some of the
functions/definitions to private mmc header files.

This change concentrates on moving the functions into private mmc headers,
following changes may continue with additional clean-ups.

Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>

mmc: vub300: Don't use mmc_card_present() when validating for inserted card

The mmc_card_present() function helps the mmc core to track an internal
state of the card device. More importantly, it's not intended to be used by
mmc host drivers to check for an inserted card. Therefore, let's stop using
it and instead rely on checking for a valid pointer to a struct mmc_card,
as it should be good enough.

Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>

mmc: omap: Don't use mmc_card_present() when validating for inserted card

The mmc_card_present() function helps the mmc core to track an internal
state of the card device. More importantly, it's not intended to be used by
mmc host drivers to check for an inserted card. Therefore, let's stop using
it and instead rely on checking for a valid pointer to a struct mmc_card,
as it should be good enough.

Cc: linux-omap@vger.kernel.org
Cc: Tony Lindgren <tony@atomide.com>
Cc: Jarkko Nikula <jarkko.nikula@bitmer.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Tony Lindgren <tony@atomide.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>

mmc: core: Remove unused struct _mmc_csd from public mmc.h header

The struct _mmc_csd isn't being used and has been lurking around for a
while. Let's kill it.

Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>

mmc: core: Move erase/trim/discard defines from public core.h to mmc.h

As the public mmc.h header already contains similar defines for other mmc
commands and arguments, let's move those for erase/trim/discard into here
as well.

Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>

mmc: core: Move some host specific public functions to host.h

Ideally the public mmc header file, core.h, shouldn't contain interfaces
particularly intended to be used by host drivers. Instead those should
remain in the host.h header file. Therefore, let's move a couple functions
from core.h to host.h.

Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>

mmc: core: Move public functions from core.h to private headers

A significant amount of functions are available through the public mmc
core.h header file. Let's slim down this public mmc interface, as to
prevent users from abusing it, by moving some of the functions to private
mmc header files.

This change concentrates on moving the functions into private mmc headers,
following changes may continue with additional clean-ups, as an example
some functions can be turned into static.

Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>

mmc: core: First step in cleaning up private mmc header files

This is the first step in cleaning up the private mmc header files. In this
change we makes sure each header file builds standalone, as that helps to
resolve dependencies.

While changing this, it also seems reasonable to stop including other
headers from inside a header itself which it don't depend upon.
Additionally, in some cases such dependencies are better resolved by
forward declaring the needed struct.

Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>

mmc: core: First step in cleaning up public mmc header files

This is the first step in cleaning up the public mmc header files. In this
change we makes sure each header file builds standalone, as that helps to
resolve dependencies.

While changing this, it also seems reasonable to stop including other
headers from inside a header itself which it don't depend upon.
Additionally, in some cases such dependencies are better resolved by
forward declaring the needed struct.

Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>

mmc: s3cmci: include linux/interrupt.h for tasklet_struct

I got this new build error on today's linux-next

drivers/mmc/host/s3cmci.h:69:24: error: field 'pio_tasklet' has incomplete type
  struct tasklet_struct pio_tasklet;
drivers/mmc/host/s3cmci.c: In function 's3cmci_enable_irq':
drivers/mmc/host/s3cmci.c:390:4: error: implicit declaration of function 'enable_irq';did you mean 'enable_imask'? [-Werror=implicit-function-declaration]

While I haven't found out why this happened now and not earlier, the
solution is obvious, we should include the header that defines
the structure.

Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

MIPS: Alchemy: Don't rely on public mmc header to include interrupt.h

The MIPS Alchemy db1300 dev board depends on interrupt.h. Explicitly
include it instead of relying on the public mmc header host.h.

Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: <linux-mips@linux-mips.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Ralf Baechle <ralf@linux-mips.org>

ARM: davinci: Don't rely on public mmc header to include interrupt.h

The davinci board omapl138-hawk, depends on interrupt.h. Explicitly include
it instead of relying on the public mmc header host.h.

Cc: Sekhar Nori <nsekhar@ti.com>
Cc: Kevin Hilman <khilman@kernel.org>
Cc: <linux-arm-kernel@lists.infradead.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Sekhar Nori <nsekhar@ti.com>

ARM: davinci: Don't rely on public mmc header to include leds.h

Some of the davinci boards, da850-evm, dm644x-evm and neuros-osd2 depends
on leds.h. Explicitly include it instead of relying on the public mmc
header host.h.

Cc: Sekhar Nori <nsekhar@ti.com>
Cc: Kevin Hilman <khilman@kernel.org>
Cc: <linux-arm-kernel@lists.infradead.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Sekhar Nori <nsekhar@ti.com>

ARM: pxa: Don't rely on public mmc header to include leds.h

Some of the pxa platforms, balloon3, colibri-pxa270-income, corgi,
trizeps4, vpac270, zeus and zylonite depends on leds.h. Explicitly include
it instead of relying on the public mmc header host.h.

Cc: Daniel Mack <daniel@zonque.org>
Cc: Haojian Zhuang <haojian.zhuang@gmail.com>
Cc: Robert Jarzmik <robert.jarzmik@free.fr>
Cc: <linux-arm-kernel@lists.infradead.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>

mmc: dt-bindings: Fix typo in mmc

This patch fix some spelling typo found in devicetree/bindings/mmc.

Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

mmc: tmio: Remove redundant check of mmc->slot.cd_irq

To validate whether native hotplug needs to be used, the tmio driver checks
whether the mmc->slot.cd_irq has been successfully assigned.

This check is redundant at its current place in tmio_mmc_host_probe(), as
the mmc core assigns mmc->slot.cd_irq a valid value first when
mmc_gpiod_request_cd_irq() is called. Therefore, let's just remove the
check for now, as that also removes a layering violation of the tmio driver
accessing core specific data via ->slot.cd_irq.

Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>

mmc: sdhci-of-esdhc: avoid clock glitch when frequency is changing

The eSDHC_PRSSTAT[SDSTB] bit indicates whether the internal card clock is
stable. This bit is for the host driver to poll clock status when changing
the clock frequency. It is recommended to clear eSDHC_SYSCTL[SDCLKEN]
to remove glitch on the card clock when the frequency is changing. This
patch is to disable SDCLKEN bit before changing frequency and enable it
after SDSTB bit is set.

Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

mmc: sdhci-pci: Add support for HS200 tuning mode on AMD, eMMC-4.5.1

This patch adds support for HS200 tuning mode on AMD eMMC-4.5.1

Reviewed-by: Sen, Pankaj <Pankaj.Sen@amd.com>
Reviewed-by: Shah, Nehal-bakulchandra <Nehal-bakulchandra.Shah@amd.com>
Reviewed-by: Agrawal, Nitesh-kumar <Nitesh-kumar.Agrawal@amd.com>
Signed-off-by: S-k, Shyam-sundar <Shyam-sundar.S-k@amd.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

mmc: mxcmmc: Include interrupt.h in the platform data header

The mxcmmc platform data header depends on interrupt.h. Don't rely on the
public mmc header host.h to include it, bud instead make that dependency
explicit.

Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

mmc: vub300: Remove bogus check of irqs_queued

It's unnecessary to check the irqs_queued value as
it always needs to queue one if irq isn't enabled.

Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

mmc: sdio: don't use rocr to check if the card could support UHS mode

Per SDIO Simplified Specification V3, section 3.1.2, A host that
supports UHS-I sets S18R to 1 in the argument of CMD5 to request a
change of the signal voltage to 1.8V. If the card supports UHS-I and
the current signal voltage is 3.3V, S18A is set to 1 in the R4 response.
If the signal voltage is already 1.8V, the card sets S18A to 0 so that
host maintains the current signal voltage. UHS-I is supported in SD mode
and S18A is always 0 in SPI mode.

For the current code, if the signaling voltage is fixed 1.8v, so
the card will set S18A to 0 for rocr and thus we would clear the
R4_18V_PRESENT from ocr, which make core won't try to use uhs mode.

To fix it, we expect sdio_read_cccr would fail if the uhs mode won't
work at all. Note that it's interesting that some sdio cards still
response S18A even the voltage is fixed to 1.8v and the CMD11 will
also accepted and finish enabling UHS mode successfully. I guess this
is why folks didn't notice this problem. Anyway, fix it.

Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

mmc: sdio: Factor out retry init card helper function

Add new helper function, mmc_sdio_resend_if_cond, to be
reused when trying to retry the init sequence.

Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

mmc: core: Use kmalloc_array() in mmc_alloc_sg()

* A multiplication for the size determination of a memory allocation
  indicated that an array data structure should be processed.
  Thus use the corresponding function "kmalloc_array".

  This issue was detected by using the Coccinelle software.

* Replace the specification of a data structure by a pointer dereference
  to make the corresponding size determination a bit safer according to
  the Linux coding style convention.

Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

mmc: mmc_test: Use kcalloc() in mmc_test_alloc_mem()

* The script "checkpatch.pl" pointed information out like the following.

  WARNING: Prefer kcalloc over kzalloc with multiply

  Thus fix the affected source code place.

* Replace the specification of a data structure by a pointer dereference
  to make the corresponding size determination a bit safer according to
  the Linux coding style convention.

Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

mmc: mmc_test: Improve a size determination in five functions

Replace the specification of a data structure by a pointer dereference
as the parameter for the operator "sizeof" to make the corresponding size
determination a bit safer according to the Linux coding style convention.

Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

mmc: mmc_test: Combine substrings for 5 messages

The script "checkpatch.pl" pointed information out like the following.

WARNING: quoted string split across lines

Thus fix affected source code places.

Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

mmc: mmc_test: Add some spaces for better code readability

Use space characters at some source code places according to
the Linux coding style convention.

Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

mmc: mmc_test: Use seq_puts() in mtf_testlist_show()

The script "checkpatch.pl" pointed information out like the following.

WARNING: Prefer seq_puts to seq_printf

Thus fix the affected source code place.

Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

mmc: mmc_test: Fix a typo in a comment line

Add a missing character in the function description.

Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

mmc: mmc_test: Use kmalloc_array() in mmc_test_area_init()

* A multiplication for the size determination of a memory allocation
  indicated that an array data structure should be processed.
  Thus use the corresponding function "kmalloc_array".

  This issue was detected by using the Coccinelle software.

* Replace the specification of a data structure by a pointer dereference
  to make the corresponding size determination a bit safer according to
  the Linux coding style convention.

Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

mmc: host: tmio: drop superfluous exit path

The probe exit path on error does nothing since commit 94b110aff8679b
("mmc: tmio: add tmio_mmc_host_alloc/free()"), so we can bail out
immediately.

Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

mmc: slot-gpio: Don't override con_id when request descriptor

The caller may supply connection ID, index, or both. All combinations are
possible and mmc framework should not make any assumption on what exactly
caller wants.

Remove con_id override conditionals in mmc_gpiod_request_ro() and
mmc_gpiod_request_cd().

Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

mmc: sdhci-pci: Remove unused member cd_con_id

cd_con_id is not used and always NULL.
Remove it to make code a bit more cleaner.

Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

mmc: mediatek: correct the implementation of msdc_card_busy

msdc_card_busy only need check if the data0 is low.
In sdio data1 irq mode, data1 may be low because of interruption.

Signed-off-by: Yong Mao <yong.mao@mediatek.com>
Signed-off-by: Chaotian Jing <chaotian.jing@mediatek.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

mmc: sdhci-of-esdhc: remove default broken-cd for ARM

Initially all QorIQ platforms were PowerPC architecture and they didn't
support card detection except several platforms. The driver added the
quirk SDHCI_QUIRK_BROKEN_CARD_DETECTION as default and this made broken-cd
property in dts node didn't work. Now QorIQ platform turns to ARM
architecture and most of them could support card detection. However it's
a large number of dts trees that need to be fixed with broken-cd if we
remove the default SDHCI_QUIRK_BROKEN_CARD_DETECTION in driver. And the
users don't want to see this. So this patch is to remove this default
quirk just for ARM and keep it for PowerPC.(Note, QorIQ PowerPC platform
only has big-endian eSDHC while QorIQ ARM platform has big-endian or
little-endian eSDHC) This makes broken-cd property work again for ARM.

Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

mmc: sdhci-esdhc: clean up register definitions

The eSDHC register definitions in header file were messy and confusing.
This patch is to clean up these definitions.

Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

mmc: dw_mmc: zx: Initial support for ZX mmc controller

This platform driver adds initial support for the DW host controller
found on ZTE SoCs.

It has been tested on ZX296718 EVB board currently. More support on
timing tuning will be added when hardware is available.

Signed-off-by: Jun Nie <jun.nie@linaro.org>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

mmc: dt-bindings: add ZTE ZX296718 MMC bindings

Document the device-tree binding of ZTE MMC host on
ZX296718 SoC.

Signed-off-by: Jun Nie <jun.nie@linaro.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

mmc: dw_mmc: Add fifo watermark alignment property

Data done irq is expected if data length is less than
watermark in PIO mode. But fifo watermark is requested
to be aligned with data length in some SoC so that TX/RX
irq can be generated with data done irq. Add the
watermark alignment to mark this requirement and force
fifo watermark setting accordingly.

Signed-off-by: Jun Nie <jun.nie@linaro.org>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

mmc: dw_mmc: Add fifo address property

The FIFO address may break default address assumption of 0x100
(version < 0x240A) and 0x200(version >= 0x240A) in current driver.
The new property is introduced to override fifo address via DT
node information.

Signed-off-by: Jun Nie <jun.nie@linaro.org>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Documentation: synopsys-dw-mshc: add binding for fifo quirks

Add fifo-addr property and fifo-watermark-quirk property to
synopsys-dw-mshc bindings. It is intended to provide more
dt interface to support SoCs specific configuration.

Signed-off-by: Jun Nie <jun.nie@linaro.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

mmc: host: Include interrupt.h in mmc host drivers that depends on it

An mmc host driver shouldn't rely on interrupt.h being included by another
public mmc header. Instead make that dependency explicit by including
interrupt.h in those host drivers that depends on it.

Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>

mmc: sdhci: Include leds.h

Don't rely on host.h to include the leds.h header, but instead include it
explicitly because the driver depends on it.

Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>

mmc: sdhci-cadence: Include mmc.h

Don't rely on host.h to include the mmc.h header, but instead include it
explicitly because the driver depends on it.

Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>

mmc: dw_mmc: Remove the public dw_mmc header file

There are currently no external users of the public dw_mmc header file,
except the dw_mmc driver itself. Therefore let's move the definitions from
the public dw_mmc header file into the existing private dw_mmc header file
and then remove the public one.

Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>

mmc: sh_mmcif: Remove unused clk_ctrl2_present from the platform data

There are currently no users of the clk_ctrl2_present member from the
platform data, so let's remove it.

Note, as some of the sh_mmcif variants may support clk_ctrl2, let's keep
the current code in the driver, which deals with this. For future support,
we should invent a DT binding instead, but let's leave that until it's
needed.

Cc: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>

mmc: sh_mmcif: Remove unused ccs_unsupported from the platform data

There are currently no users of the ccs_unsupported member from the
platform data, so let's remove it.

Note, as some of the sh_mmcif variants may not support ccs, let's keep the
current code in the driver, which deals with this. For future support, we
should invent a DT binding instead, but let's leave that until it's needed.

Cc: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>

mmc: sh_mmcif: Remove unused ->get_cd() platform callback

Removing the callback also enables us to remove the sh_mmcif_get_cd()
altogether, as we convert to use mmc_gpio_get_cd() to the same kind of
work.

Cc: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

mmc: sh_mmcif: Remove unused use_cd_gpio/cd_gpio from platform data

Cc: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>

mmc: Removed the unused public mmc boot.h header

Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>

sh: sh7724: Don't use a public mmc header for MMC_PROGRESS*

The enum that specifies the MMC_PROGRESS* types, is a sh mmcif specific
thing and has no relevance in a public mmc header. Currently it's used only
by the sh romImage MMCIF boot, so let's instead define the enum in there
and rename the types to MMCIF_* to show this.

Cc: linux-sh@vger.kernel.org
Cc: Simon Horman <horms@verge.net.au>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Cc: Rich Felker <dalias@libc.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>

mmc: sdhci-iproc: Increase max_blk_size for bcm2835

According to the BCM2835 datasheet the maximum block size for the
eMMC module is restricted to the internal data FIFO which is 1024 byte.
But this is still an improvement to the default of 512 byte.

Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Eric Anholt <eric@anholt.net>
Acked-by: Scott Branden <scott.branden@broadcom.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>