ASoC: twl6040: Function to fetch the TRIM values

Provide API to fetch the TRIM values (for machine drivers)

Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: twl6040: Read the TRIM values from the chip

Update the reg_cache with values from chip regarding to TRIM.

Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: Drop exporting ad1980_dai

ad1980_dai is not used outside this driver,
thus drop exporting it.

Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: Drop exporting sn95031_get_mic_bias

sn95031_get_mic_bias() is not used outside this driver
and it is a static function now.
Thus drop exporting sn95031_get_mic_bias.

Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: omap-mcbsp: Fix compile time warning about ambiguous ‘else’

Fixes the following compile time warning:
omap-mcbsp.c:519: warning: suggest explicit braces to avoid ambiguous ‘else’

Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: Set idle_bias_off for WM1250 EV1

The WM1250 EV1 is functionally digital in a system (the analogue I/O
is either ground referenced or always powered) so flag it as idle_bias_off.

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: Add platform data for WM1250 EV1 GPIOs

The WM1250 EV1 has some GPIOs which can be used to control the behaviour
at runtime. Request them all if supplied and add a set_bias_level()
function to start and stop the clocks.

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: Don't force bias on ground referenced devices

Currently we force all devices in the system to be at the same bias level.
This is due to concerns about power or pop/click impacts from either
ramping VMID or mismatching VMID on the analogue I/O lines between
connected devices but does mean we power devices up more often than we
really need to.

If a device flags idle_bias_off this will usually mean that it's either
all digital or ground referenced (in which case the idle and powered bias
levels are identical) so this concern does not apply and we can save some
power by leaving it off when not needed itself.

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: Add DMIC control to Speyside WM8962 board

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: Add support for on-board analogue microphones on Speyside WM8962

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: Convert WM8962 MICBIAS to a supply widget

A supply widget is generally clearer than a MICBIAS widget and a mic bias
is just a type of supply so use a supply widget for the MICBIAS. This also
avoids confusion with the routing when connected to multiple inputs.

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: Rename WM8962 DMIC widget to DMIC_ENA

Matches the register name and avoids confusion with board widgets.

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: Support a wider range of sample rates on Speyside WM8962

As we've only got one audio interface and it is symmetric we can just set
SYSCLK based on the sample rate requested by the application layer. Provide
a default so bypass paths work before audio playback.

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: Add missed free_irq in wm5100_remove and wm5100_probe error path

Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: Remove unneeded mutex_init in wl1273_probe()

Since f0fba2ad "ASoC: multi-component - ASoC Multi-Component Support",
snd_soc_register_codec() now does all the codec list and mutex init.
Thus don't need to call mutex_init(&codec->mutex) in wl1273_probe() any more.

Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: Staticize sn95031_dais

Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: Staticize rt5631_dai

Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: twl6040: No need to read the INTID register

Since our irq handler has been called, it is granted, that
the reason was either PLUGINT, or UNPLUGINT.
The INTID register has been checked in the MFD part of
twl6040 driver (twl6040-irq.c).
We have no reason to read from chip again here.

Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: omap-mcpdm: Correct the supported number of channels

OMAP4 McPDM supports 5 downlink (playback), and
3 uplink (capture) channels.

Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Merge branch 'for-3.1' into for-3.2

ASoC: omap-mcbsp: Do not attempt to change DAI sysclk if stream is active

Attempt to change McBSP CLKS source while another stream is active is not
safe after commit d135865 ("OMAP: McBSP: implement functional clock
switching via clock framework") in 2.6.37.

CLKS parent clock switching using clock framework have to idle the McBSP
before switching and then activate it again. This short break can cause a
DMA transaction error to already running stream which halts and recovers
only by closing and restarting the stream.

This goes more fatal after commit e2fa61d ("OMAP3: l3: Introduce
l3-interconnect error handling driver") in 2.6.39 where l3 driver detects a
severe timeout error and does BUG_ON().

Fix this by not changing any configuration in omap_mcbsp_dai_set_dai_sysclk
if the McBSP is already active. This test should have been here just from
the beginning anyway.

Signed-off-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@kernel.org

ASoC: Add Kconfig and Makefile entries for rt5631 codec

Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: Add missed BCLK rate to WM5100 driver

Reported-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: Add another DAPM stat for neighbour checks

The number of times we look at a potentially connected neighbour is just
as important as the number of times we actually recurse into looking at
that neighbour so also collect that statistic.

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: Dynamically manage DBVDD2 and DBVDD3 on WM5100

Allow the DBVDD2 and DBVDD3 rails to be powered down when idle, helping
fully power down connected devices when idle.

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC/MFD: twl6040: Combine bit definitions for Headset control registers

Use one set of defines for the HS bits, since they are identical in both
control register.

Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: twl6040/sdp4430: Change legacy DAI name

Change the legacy DAI name from "twl6040-hifi" to "twl6040-legacy" to
be more intuitive.

Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: twl6040: Support for AUX L/R output

AUX L/R outputs can be driver from the Handsfree PGA output.

Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: twl6040: Use consistent names for Headset path

Use "Headset XYZ" for user visible controls, while the internal DAPM
widgets can use "HS XYZ".
In this way we can group the Headset related controls in UI
(alsamixer for example).

Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: twl6040: Use consistent names for Handsfree path

Use "Handsfree XYZ" for user visible controls, while the internal DAPM
widgets can use "HF XYZ".
In this way we can group the Handsfree related controls in UI
(alsamixer for example).

Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: twl6040: Earphone path correction

Fix the DAPM routing for the earphone path.
Convert the DAPM_SWITCH_E to DAPM_OUT_DRV_E, so we can have correct
power up, and down sequence for EP.
Introduce mute control (Earphone Playback Switch) for users to
enable/disable the EP path.
Note: the EP does not have it's own dedicated DAC. EP is connected to
HSL DAC.

Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: twl6040: Introduce SW only shadow register

Software only shadow register to be used by the driver.
For example Earpiece path will need this shadow register.

Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: twl6040: Remove strings "NULL" from DAPM route

Replace the string with plain NULL.

Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: twl6040: Fix comments for register names

Change the register name strings in the comments for the
twl6040_reg table, so it is easier to search for specific
register.

This is cosmetic change.

Before we had for example:
TWL6040_REG_HSLCTL as register definition.

At the register table we had:
TWL6040_HSLCTL

Searching for TWL6040_HSLCTL resulted no hits.

While if we look for REG_HSLCTL, we can find the places
the register has been used.

Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: twl6040: Lower the power on gain values at startup

The default gains on outputs/inputs are set to 0dB.
This is fixing the pop noise issue at the first playback, which
caused by the wrong starting point of the ramp code.
The ramp code for the outputs expects the gains to be in
their lowest configuration in order to be effective.
After the playback stops, the ramp code takes care of
ramping down the gains to their minimum.

Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Merge branch 'peter/topic/for-mark/mcpdm_for-3.2' of git://gitorious.org/omap-audio/linux-audio into for-3.2

ASoC: Include delay.h in 88pm860x

Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: omap-mcpdm: Replace legacy driver

Reasons for the replacement:
The current driver for McPDM was developed to support the legacy mode only.
In preparation for the ABE support the current driver stack need the be
replaced.
The new driver is much simpler, easier to extend, and it also fixes some of the
issues with the old stack.

Main changes:
- single file for omap-mcpdm (mcpdm.c/h removed)
- Define names for registers, bits cleaned up, prefixed
- Full-duplex audio operation (arecord | aplay) has been fixed
- Less code

McPDM need to be turned off after all streams has been stopped.
This might cause pop noise on the output, if the codec's DAC is
still powered at this time.

Signed-off-by: Misael Lopez Cruz <misael.lopez@ti.com>
Signed-off-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Sebastien Guiriec <s-guiriec@ti.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: OMAP4: McPDM: Convert to hwmod/omap_device

In order to probe, and operate correctly, the OMAP McPDM driver needs to
be converted to use hwmod.
The device name has been changed to probe the driver.
Replace the clk_* with pm_runtime_* calls to manage the clocks correctly.
Missing request_mem_region/release_mem_region added.

Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>

ASoC: omap-mcpdm: Fix threshold and dma configuration

DMA packet_size must be configured based on the McPDM FIFO threshold
value, number of channels.
Due to the FIFO operation the DMA muse be configured differently for
playback, and capture.
At the same time fix the McPDM threshold values used for playback, and
capture to avoid broken code.

Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>

OMAP4: hwmod: enable mcpdm hwmod device.

Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Jorge Eduardo Candelaria
Signed-off-by: Margarita Olaya Cabrera
Signed-off-by: Liam Girdwood <lrg@ti.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Benoit Cousson <b-cousson@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>

OMAP: McPDM: Convert McPDM device to omap_device

McPDM device is converted to omap device.

Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Jorge Eduardo Candelaria
Signed-off-by: Margarita Olaya Cabrera
Signed-off-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Misael Lopez Cruz <misael.lopez@ti.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>

ASoC: tpa6130a2: Remove model_id from platform data

The model_id is no longer needed within the platform_data
for the TPA driver since the model of TPA specified
with the device name (tpa6130a2/tpa6140a2).

Also update rx51 (the only affected user) to use the device name rather
than platform data.

Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Tested-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: tpa6130a2: Model support cleanup

Use the device name and driver_data to identify
the TPA model supported by the driver.
Board files should use either "tpa6130a2" or
"tpa6140a2" as device name to specify the model
in used on the specific board.

Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Tested-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: soc-core: symmetry checking for each DAIs separately

The orginal code does not cover the case that one DAI such as codec
may be shared between other two DAIs(CPU).
When do symmetry checking, altough the codec DAI requires symmetry,
the two CPU DAIs may still be configured to run on different rates.

We change to check each DAI's state separately instead of only checking
the dai link to prevent this issue.

Signed-off-by: Dong Aisheng <b29396@freescale.com>
Tested-by: Wolfram Sang <w.sang@pengutronix.de>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: 88pm860x-codec - reset the codec correctly

Reset the codec according to the Audio power-up delay errata for the 88PM8607.

Signed-off-by: Bas Vermeulen <bas.vermeulen@novero.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: 88pm860x-codec - Allow independent use of both I2S playback and capture

Introduce a I2S CLK supply so playback and capture can operate independently.

Signed-off-by: Bas Vermeulen <bas.vermeulen@novero.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: Add driver for rt5631

Signed-off-by: Johnny Hsu <johnnyhsu@realtek.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: Staticise nuc900_dma_getposition()

It is not used outside this driver so no need to make the symbol global.

Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: Staticise jz4740_pcm_new()

It is not used outside this driver so no need to make the symbol global.

Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: Staticise bf5xx_pcm_i2s_new()

It is not used outside this driver so no need to make the symbol global.

Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: Staticise bf5xx_pcm_ac97_new()

It is not used outside this driver so no need to make the symbol global.

Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Merge branch 'for-3.1' into for-3.2

ASoC: Ensure we generate a driver name

Commit 873bd4c (ASoC: Don't set invalid name string to snd_card->driver
field) broke generation of a driver name for all ASoC cards relying on the
automatic generation of one. Fix this by using the old default with spaces
replaced by underscores.

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Takashi Iwai <tiwai@suse.de>

ASoC: Factor out per-widget DAPM power checks

The indentation is getting a little deep. Should be straight code motion,
no functional changes.

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: Trace and collect statistics for DAPM graph walking

One of the longest standing areas for improvement in ASoC has been the
DAPM algorithm - it repeats the same checks many times whenever it is run
and makes no effort to limit the areas of the graph it checks meaning we
do an awful lot of walks over the full graph. This has never mattered too
much as the size of the graph has generally been small in relation to the
size of the devices supported and the speed of CPUs but it is annoying.

In preparation for work on improving this insert a trace point after the
graph walk has been done. This gives us specific timing information for
the walk, and in order to give quantifiable (non-benchmark) numbers also
count every time we check a link or check the power for a widget and report
those numbers. Substantial changes in the algorithm may require tweaks to
the stats but they should be useful for simpler things.

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: Add WM5100 driver

The WM5100 is a highly integrated low power audio subsystem with advanced
digital signal processing capabilities including effects, speech clarity
enhancement and active noise cancellation.  This initial driver provides
support for basic audio paths, further patches will provide more
complete functionality.

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>

Merge branch 'for-3.1' into for-3.2

ASoC: ssm2602: Do not dereference codec->control_data

The driver assumes that control_data points to the drivers i2c_client struct,
but this is no longer the case since the ASoC core has switched to regmap.

Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: fsl: Fix error handling if platform_device_add fails

Call platform_device_put() instead of platform_device_unregister() if
platform_device_add() fails.

Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: Remove bitrotted wm8962_resume()

This functionality is now subsumed within the bias management, using the
standard cache management functionality, without assuming the cache type.

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>

ASoC: Refcount WM8996 bandgap from FLL too

For digital only paths we need to make sure the bandgap is enabled prior
to starting the FLL which isn't tied into DAPM.

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>

ASoC: Fix unused variable warning in WM8996

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>

ASoC: twl6040: Correct supported number of playback channels

twl6040 supports 5 playback, and 2 capture channels

Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: twl6040: Fix the number of channels for vibra

Only mono audio can be used for vibra (DL4 channel).

Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: twl6040: Use chip defaults in the initial reg_cache

Reset the twl6040_reg array to hold the chip default values.
The only changed values were for the microphone input selection.
Select no input for the microphones in the twl6040_init_chip function.

Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: twl6040: Chip initialization cleanup

There is no need to write to the vio registers at probe time, since most
them either read only, or shared with MFD or not used.
On the other hand it is a good idea to updated the ASICREV register in
the cache at this time.

After power up we need to restore some registers. Clean up the list to
contain only the registers we are going to restore.

Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

MFD: twl6040: Fix power on GPIO handling

Avoid requesting the audpwron gpio in case of ES1.0
revision.
In the past we requested the gpio, but we did not
free it up, since we made the check for the revision
later. This results later checks for gpio validity to
fail, leaving the gpio reserved (even after the driver
has been removed).

Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Input: twl6040-vibra: Use accessor to get revision information

Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Dmitry Torokhov <dtor@mail.ru>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

MFD: twl6040: Add accessor for revision ID

For client driver to use, if they need chip resvision information.

Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

MFD: twl6040: Remove global pointer for platform_device

There is no need to keep global pointer for the platform
device, since it is only used for dev_* prints, and the
device pointer available within the twl6040 structure.

Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: mxs-saif: add record function

1. add different clkmux mode handling
SAIF can use two instances to implement full duplex (playback &
recording) and record saif may work on EXTMASTER mode which is
using other saif's BITCLK&LRCLK.

The clkmux mode could be set in pdata->init() in mach-specific code.
For generic saif driver, it only needs to know who is his master
and the master id is also provided in mach-specific code.

2. support playback and capture simutaneously however the sample
rates can not be different due to hw limitation.

Signed-off-by: Dong Aisheng <b29396@freescale.com>
Acked-by: Wolfram Sang <w.sang@pengutronix.de>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: sn95031: Staticize sn95031_pcm_hw_params

Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Vinod Koul <vinod.koul@linux.intel.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: Add line loads to the list of supported detections for Speyside

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>

ASoC: Initial WM8996 headphone impedance measurement support

The WM8996 can measure the impedance of accessories connected to the
headphone output. Implement initial support for this, measuring the
left channel impedance when an accessory is detected and using this
to distinguish between a line load and a headphone load.

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>

ASoC: WM8996 only needs bandgap for analogue functionality

Rather than managing the bandgap in the bias level control use a supply
widget as we only actually need to enable it for analogue paths, not
fully digital ones.

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>

ASoC: Display the error code when we fail to add a DAPM control

Useful for diagnostics.

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>

ASoC: support all possible sample rates in the WM8776 driver

The WM8776 supports a continuous range of sample rates rather than
discrete values and supports a wider range of sample rates on the
playback path than is currently supported.  Update the constraints on
the DAIs to reflect this.

Signed-off-by: Timur Tabi <timur@freescale.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: wm8995: Remove unused i2c variable in wm8995_remove()

Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: wm8995: Return -EINVAL if device ID mismatch

Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: tpa6130a2: Remove obsolete cleanup for clientdata

The i2c core will clear the clientdata pointer automatically,
we don't have to set the `data' field to NULL in remove() or
if probe() failed anymore.

Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: davinci-pcm: trivial: replace link with actual chan/link

The ambiguously named variable 'link' is used as a temporary throughout
davinci-pcm -- its presence makes grepping (and groking) the code
difficult.

Replace link with the value of link in almost all sites. The exception
is a couple places where the last-assigned link/chan needs to be
returned by a function -- in these cases, rename to last_link.

Signed-off-by: Ben Gardiner <bengardiner@nanometrics.ca>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: edb93xx: convert to use snd_soc_register_card()

Current method for machine driver to register with the ASoC core is to use
snd_soc_register_card() instead of creating a "soc-audio" platform device.

Signed-off-by: Mika Westerberg <mika.westerberg@iki.fi>
Reviewed-by: Ryan Mallon <rmallon@gmail.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: simone: convert to use snd_soc_register_card()

Current method for machine driver to register with the ASoC core is to
use snd_soc_register_card() instead of creating a "soc-audio" platform device.

In addition we use platform_device_register_simple() to create a platform
device for the codec. This function will handle putting and deleting the
device automatically which simplifies the error handling in the machine
driver.

Signed-off-by: Mika Westerberg <mika.westerberg@iki.fi>
Reviewed-by: Ryan Mallon <rmallon@gmail.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: ep93xx-pcm: add MODULE_ALIAS

To get the PCM module loaded automatically by udev et al. we need to add a
proper MODULE_ALIAS.

Signed-off-by: Mika Westerberg <mika.westerberg@iki.fi>
Reviewed-by: Ryan Mallon <rmallon@gmail.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ARM: ep93xx: snappercl15: register audio platform device

Since the ASoC machine driver is now a platform driver we need to register a
matching platform device.

Signed-off-by: Mika Westerberg <mika.westerberg@iki.fi>
Reviewed-by: Ryan Mallon <rmallon@gmail.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ARM: ep93xx: edb93xx: register audio platform device

Since the ASoC machine driver is now a platform driver we need to register a
matching platform device.

Signed-off-by: Mika Westerberg <mika.westerberg@iki.fi>
Reviewed-by: Ryan Mallon <rmallon@gmail.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ARM: ep93xx: simone: register audio platform device

Since the ASoC machine driver is now a platform driver we need to register
a matching platform device.

Signed-off-by: Mika Westerberg <mika.westerberg@iki.fi>
Reviewed-by: Ryan Mallon <rmallon@gmail.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: snappercl15: convert to use snd_soc_register_card()

Current method for machine driver to register with the ASoC core is to use
snd_soc_register_card() instead of creating a "soc-audio" platform device.

Signed-off-by: Mika Westerberg <mika.westerberg@iki.fi>
Reviewed-by: Ryan Mallon <rmallon@gmail.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: support sample sizes properly in the WM8776 codec driver

Use snd_pcm_format_width() to determine the sample size, instead of
checking specify sample formats and assuming that those are the only
valid format.

This change adds support for big-endian architectures (which use the _BE
formats) and the packed 24-bit format (SNDRV_PCM_FORMAT_S24_3xE).

[Fixed single letter variable name legibility problem -- broonie]

Signed-off-by: Timur Tabi <timur@freescale.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Merge branch 'for-3.1' into for-3.2

ASoC: Fix WM8996 DC servo operation without IRQ

We need to count the timeout down.

Reported-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>

ASoC: bf5xx-ad73311: Fix prototype for bf5xx_probe

Fix below build warning:
sound/soc/blackfin/bf5xx-ad73311.c: warning: initialization from incompatible pointer type

Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: samsung: Fix checking return value of clk_get

clk_get() returns a pointer to the struct clk or an ERR_PTR().
This patch also use PTR_ERR() for return value.

Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: improve asynchronous mode support in the fsl_ssi driver

The Freescale SSI audio controller supports "synchronous" and "asynchronous"
modes.  In synchronous mode, playback and capture use the same input clock,
so sample rates must be the same during simultaneous playback and capture.
Unfortunately, the code which supports asynchronous mode is just broken in
various ways.  In particular, it was constraining sample sizes as well as
the sample rate.

The fix also allows us to simplify the code by eliminating the 'asynchronous',
'playback', and 'capture' variables that were used to keep track of playback
and capture streams.

Unfortunately, it turns out that simulataneous playback and record does not
actually work on the only platform that supports asynchronous mode: the
Freescale P1022DS reference board.  If a second stream is started, the SSI
grinds to halt for both streams.  This is true even if the P1022 is configured
for synchronous mode, so it's likely a hardware problem that needs to be
worked around.

Signed-off-by: Timur Tabi <timur@freescale.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: Correct channel numbers for WM8996 AIF2

The AIF1 channels are numbered from zero than one; do the same thing for
AIF2 too.

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>

ASoC: Disable WM8996 CPVDD supply when not in use

The WM8996 only requires CPVDD when the charge pump is active so control
it separately to the other supplies, only enabling it when the charge pump
is active. This will result in a small power saving on systems which are
able to provide independent software control of the supply.

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>

regulator: Implement deferred disable support

It is a reasonably common pattern for hardware to require some delay after
being quiesced before the disable has finalised, especially in mixed signal
devices. For example, an active discharge may be required to ensure that
the circuit starts up again in a known state. Avoid having to implement
such delays in the regulator API by providing regulator_deferred_disable()
which will do a regulator_disable() a specified number of milliseconds
after it is called.

Due to the reference counting done on regulators a deferred disable can
be cancelled by doing another regulator_enable().

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>

ASoC: Fix trivial build regression in Kirkwood I2S

A fix merged in 3.1-rc2 introduced a small regression, this should get it
to build again.

Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: ad193x: Setup regmap read and write flag masks for SPI

Currently register read-back for the ad193x is broken, because it expects bit 0
of the upper byte to be set to indicate a read operation, while the regmap
default for SPI is to use bit 7.

This patch also addresses another oddity of the device. There are SPI and I2C
versions of this codec. In both cases the registers are 8-bit wide and numbered
from 0x0 to 0x10, but in the SPI case there is also a so called
'global address' which is prefixed in-front of the register address. The global
address mimics I2C behaviour and includes a static device address the and the
read/write flag. This basically extends the register address to an 16-bit value
numbered from 0x800 to 0x810. These are the register numbers which are
currently used by the driver. This works, because I2C will ignore the upper
8 bits of the register, but it is still a bit confusing, as there are no such
register numbers in the I2C case.

The approach taken by this patch is to number the registers from 0x00 to 0x10
and encode the global address for SPI mode into the read and write flag masks.

Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>