bna: make function tables cont

To prevent malicious usage, all tables of pointers must be const.

Compile tested only.
Gleaned for PAX.

Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

pcnet32: constify function table

Function tables need to be const to prevent malicious use.

This is compile tested only.
Gleaned from PAX.

Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

wan: make LAPB callbacks const

This is compile tested only.
Suggested by dumpster diving in PAX.

Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

ipv6: Send ICMPv6 RSes only when RAs are accepted

This patch improves the logic determining when to send ICMPv6 Router
Solicitations, so that they are 1) always sent when the kernel is
accepting Router Advertisements, and 2) never sent when the kernel is
not accepting RAs. In other words, the operational setting of the
"accept_ra" sysctl is used.

The change also makes the special "Hybrid Router" forwarding mode
("forwarding" sysctl set to 2) operate exactly the same as the standard
Router mode (forwarding=1). The only difference between the two was
that RSes was being sent in the Hybrid Router mode only. The sysctl
documentation describing the special Hybrid Router mode has therefore
been removed.

Rationale for the change:

Currently, the value of forwarding sysctl is the only thing determining
whether or not to send RSes. If it has the value 0 or 2, they are sent,
otherwise they are not. This leads to inconsistent behaviour in the
following cases:

* accept_ra=0, forwarding=0
* accept_ra=0, forwarding=2
* accept_ra=1, forwarding=2
* accept_ra=2, forwarding=1

In the first three cases, the kernel will send RSes, even though it will
not accept any RAs received in reply. In the last case, it will not send
any RSes, even though it will accept and process any RAs received. (Most
routers will send unsolicited RAs periodically, so suppressing RSes in
the last case will merely delay auto-configuration, not prevent it.)

Also, it is my opinion that having the forwarding sysctl control RS
sending behaviour (completely independent of whether RAs are being
accepted or not) is simply not what most users would intuitively expect
to be the case.

Signed-off-by: Tore Anderson <tore@fud.no>
Signed-off-by: David S. Miller <davem@davemloft.net>

can-gw: add netlink based CAN routing

This patch adds a CAN Gateway/Router to route (and modify) CAN frames.

It is based on the PF_CAN core infrastructure for msg filtering and msg
sending and can optionally modify routed CAN frames on the fly.
CAN frames can *only* be routed between CAN network interfaces (one hop).
They can be modified with AND/OR/XOR/SET operations as configured by the
netlink configuration interface known e.g. from iptables. From the netlink
view this can-gw implements RTM_{NEW|DEL|GET}ROUTE for PF_CAN.

The CAN specific userspace tool to manage CAN routing entries can be found in
the CAN utils http://svn.berlios.de/wsvn/socketcan/trunk/can-utils/cangw.c
at the SocketCAN SVN on BerliOS.

Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

sfc: Use correct fields of struct ethtool_coalesce

An earlier developer misunderstood the meaning of the 'irq' fields and
the driver did not support the standard fields.  To avoid invalidating
existing user documentation, we report and accept changes through
either the standard or 'irq' fields.  If both are changed at the same
time, we prefer the standard field.

Also explain why we don't currently use the 'max_frames' fields.

Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

sfc: Validate IRQ moderation parameters in efx_init_irq_moderation()

Add a range check, and move the check that RX and TX are consistent
from efx_ethtool_set_coalesce().

Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

sfc: Correct reporting and validation of TX interrupt coalescing

The reported TX IRQ moderation is generated in a completely crazy way.
Make it simple and correct.

When channels are shared between RX and TX, TX IRQ moderation must be
the same as RX IRQ moderation, but must be specified as 0!  Allow it
to be either specified as the same, or left at its previous value
in which case it will be quietly overridden.

Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

sfc: Use consistent types for interrupt coalescing parameters

Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

sfc: Correct error code for unsupported interrupt coalescing parameters

Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge git://github.com/Jkirsher/net-next

Merge branch 'for-davem' of git://git.infradead.org/users/linville/wireless-next

Merge branch 'master' of ../netdev-next/

ixgbe: Correctly name and handle MSI-X other interrupt

It was possible to inadvertently add additional interrupt causes to the
MSI-X other interrupt.  This occurred when things such as RX buffer overrun
events were being triggered at the same time as an event such as a Flow
Director table reinit request.  In order to avoid this we should be
explicitly programming only the interrupts that we want enabled.  In
addition I am renaming the ixgbe_msix_lsc function and interrupt to drop
any implied meaning of this being a link status only interrupt.

Unfortunately the patch is a bit ugly due to the fact that ixgbe_irq_enable
needed to be moved up before ixgbe_msix_other in order to have things
defined in the correct order.

Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

ixgbe: cleanup configuration of EITRSEL and VF reset path

This change is meant to cleanup some of the code related to SR-IOV and the
interrupt registers.  Specifically I am moving the EITRSEL configuration
into the MSI-X configuration section instead of enablement.  Also I am
fixing the VF shutdown path since it had operations in the incorrect order.

Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

ixgbe: cleanup reset paths

The reset paths are overly complicated and are either missing steps or
contain extra unnecessary steps such as reading MAC address twice.  This
change is meant to help clean up the reset paths an get things functioning
correctly.

Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

ixgbe: Update TXDCTL configuration to correctly handle WTHRESH

This change updated the TXDCTL configuration.  The main goal is to be much
more explicit about the configuration and avoid a possible fake TX hang
when the interrupt throttle rate is set to 0.

Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

ixgbe: combine PCI_VDEVICE and board declaration to same line

This patch is a minor whitespace cleanup to compress the device ID
declaration and board type declaration onto the same line.  It seems to
make sense since all of the combinations of the two are less than 80
characters and it makes the overall layout a bit more readable.

Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

ixgbe: Drop unnecessary adapter->hw dereference in loopback test setup

This patch drops a set of unnecessary dereferences to the hardware structure
since we already have a local copy of the hardware pointer.

Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

ixgbe: commonize ixgbe_map_rings_to_vectors to work for all interrupt types

This patch makes it so that the map_rings_to_vectors call will work with
all interrupt types.  The advantage to this is that there will now be a
predictable mapping for all given interrupt types.

Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

ixgbe: Use ring->dev instead of adapter->pdev->dev when updating DCA

This change switches us over to using the ring->dev pointer instead of
having to use the adapter->pdev->dev reference.  The advantage to this is
that it is a much shorter route to get the to final needed value.

Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

ixgbe: cleanup allocation and freeing of IRQ affinity hint

The allocation and freeing of the IRQ affinity hint needs some updates
since there are a number of spots where we run into possible issues with
the hint not being correctly updated.

Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

v2 ixgbe: consolidate all MSI-X ring interrupts and poll routines into one

This change consolidates all of the MSI-X interrupt and polling routines
into two single functions.  One for the interrupt and one for the code.
The main advantage to doing this is that the compiler can optimize the
routines into single monolithic functions which should allow all of them
function to occupy a single block of memory and as such avoid jumping
around.

Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

ixgbe: Change default Tx work limit size to 256 buffers

This change makes it so that the default Tx work limit is 256 buffers or
1/2 of an entire ring instead of a full ring size so that it is much more
likely that we will be able to actually reach the work limit value.
Previously with the value set to an entire ring it would not have been
possible for us to trigger an event due to the fact that the Tx work is
stopped at the point where we cannot place one more buffer on the ring and
it is not restarted until cleanup is complete.

Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

net: consolidate and fix ethtool_ops->get_settings calling

This patch does several things:
- introduces __ethtool_get_settings which is called from ethtool code and
  from drivers as well. Put ASSERT_RTNL there.
- dev_ethtool_get_settings() is replaced by __ethtool_get_settings()
- changes calling in drivers so rtnl locking is respected. In
  iboe_get_rate was previously ->get_settings() called unlocked. This
  fixes it. Also prb_calc_retire_blk_tmo() in af_packet.c had the same
  problem. Also fixed by calling __dev_get_by_index() instead of
  dev_get_by_index() and holding rtnl_lock for both calls.
- introduces rtnl_lock in bnx2fc_vport_create() and fcoe_vport_create()
  so bnx2fc_if_create() and fcoe_if_create() are called locked as they
  are from other places.
- use __ethtool_get_settings() in bonding code

Signed-off-by: Jiri Pirko <jpirko@redhat.com>
v2->v3:
-removed dev_ethtool_get_settings()
-added ASSERT_RTNL into __ethtool_get_settings()
-prb_calc_retire_blk_tmo - use __dev_get_by_index() and lock
 around it and __ethtool_get_settings() call
v1->v2:
        add missing export_symbol
Reviewed-by: Ben Hutchings <bhutchings@solarflare.com> [except FCoE bits]
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

net/irda: sh_irda: add PM support

Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net/irda: sh_irda: update author's email address

it also cleanup white space

Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net/irda: sh_irda: add sh_irda_ prefix to all functions

Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

tg3: Code movement

This patch just moves some code around for better organization.

Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Benjamin Li <benli@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

tg3: Eliminate tg3_halt_cpu() prototype

This patch moves the implementatino of tg3_halt_cpu() earlier in the
file to eliminate its prototype.

Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Benjamin Li <benli@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

tg3: Eliminate tg3_write_sig_post_reset() prototype

This patch moves the implementation of tg3_write_sig_post_reset()
earlier to eliminate its prototype.

Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Benjamin Li <benli@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

tg3: Eliminate tg3_stop_fw() prototype

This patch moves tg3_stop_fw() earlier in the file to eliminate its
prototype.

Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Benjamin Li <benli@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

tg3: Add ability to turn off 1shot MSI

In older devices, 1-shot MSI mode had to be enabled by the code.  In
newer devices however, 1-shot MSI mode is enabled by default; code would
be needed to disable it.

Disabling 1-shot MSI mode is useful when debugging.  This patch changes
the code so that the TG3_FLAG_1SHOT_MSI accurately reflects (and
controls) the state of 1-shot MSI mode.

Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Benjamin Li <benli@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

tg3: Remove tp->rx_offset term when unneeded

This patch removes the tp->rx_offset term if NET_IP_ALIGN is defined to
zero.

Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Benjamin Li <benli@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

tg3: Fix missed MSI workaround

This patch fixes a minor counter initialization bug and makes the MSI
workaround slightly more efficient by attempting to service pending
interrupts before applying the workaround.

Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Benjamin Li <benli@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

tg3: Check all adv bits when checking config

This patch makes sure the driver checks all advertisement bits when
checking the current hw advertisements.

Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Benjamin Li <benli@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

MII: fix Kconfig dependencies for MII

MII Kconfig option is apart of the core networking drivers and
by default NET_CORE is enabled so drivers selecting MII will
have MII enabled as well.  It was found using the randconfig
option during testing, MII would be selected but NET_CORE
could be disabled.  This caused a dependency error.

Resolved the dependency by selecting NET_CORE when MII is
selected.

Reported-by: Emil Tantilov <emil.s.tantilov@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

stmmac: update the doc with new info about the driver's debug (v3)

Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

stmmac: update the driver version (Aug_2011) (v3)

Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

stmmac: add HW DMA feature register (v3)

New GMAC chips have an extra register to indicate
the presence of the optional features/functions of
the DMA core.

This patch adds this support and all the HW cap
are exported via debugfs.

Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

stmmac: rework the code to get the Synopsys ID (v3)

The Synopsys ID is now passed from the MAC core
to the main. This info will be used for managing
the HW cap register (supported in the new GMAC
generations).

Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

stmmac: export DMA TX/RX rings via debugfs (v3)

This patch adds the following debugFs entry to dump the
RX/TX DMA rings:

/sys/kernel/debug/stmmaceth/descriptors_status

This is an example:

=======================
  RX descriptor ring
=======================
[0] DES0=0x85ee0320 DES1=0x1fff1fff BUF1=0x5fae2022 BUF2=0x0
[1] DES0=0x85ee0320 DES1=0x1fff1fff BUF1=0x5fae0022 BUF2=0x0
[2] DES0=0x81460320 DES1=0x1fff1fff BUF1=0x5f9dd022 BUF2=0x0

Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

stmmac: add MMC support exported via ethtool (v3)

This patch adds the MMC management counters support.
MMC module is an extension of the register address
space and all the hardware counters can be accessed
via ethtoo -S ethX.

Note that, the MMC interrupts remain masked and the logic
to handle this kind of interrupt will be added later (if
actually useful).

Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

stmmac: support wake up irq from external sources (v3)

On some platforms e.g. SPEAr the wake up irq differs from the
GMAC interrupt source.
With this patch an external wake up irq can be passed through the
platform code and named as "eth_wake_irq".

In case the wake up interrupt is not passed from the platform
so the driver will continue to use the mac irq (ndev->irq)

Signed-off-by: Deepak Sikri <deepak.sikri@st.com>
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

stmmac: remove the mmc code (v3)

DWMAC Management Counters (MMC) are not fully support.
The minimal support added in the past allowed to
only disable counters (if present) and mask their
interrupts.
This patch prepares the driver to support the MMC
removing obsolete code.

Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

stmmac: remove the STBus bridge setting from the GMAC code (v3)

This patch removes a piece of code (actually commented)
only useful for some ST platforms in the past.

This kind of setting now can be done by using the platform
callbacks provided in linux/stmmac.h (see the stmmac.txt for
further details).

Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

6LoWPAN: fix skb_copy call

This patch fixes 2 issues in lowpan_skb_deliver function:
1. Check for return status of skb_copy call;
2. Use skb_copy with proper GFP flag, drop check for non-interrupt
context.

Signed-off-by: Alexander Smirnov <alex.bluesman.smirnov@gmail.com>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

br: remove redundant check and init

Since these checks and initialization are done in
dev_ethtool_get_settings called later on, remove this redundancy.

Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Acked-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

mii: Remove references to DP83840 PHY in mii.h

There are references to this PHY chip in the generic mii.h header, so removing them.
Re-jiggle the changed comments, in response to points raised by Ben Hutchings.

Signed-off-by: Mark Einon <mark.einon@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

mii: Convert spaces to tabs in mii.h

Whitespace changes - spaces converted to tabs after each define name and value

Signed-off-by: Mark Einon <mark.einon@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: linkwatch: allow vlans to get carrier changes faster

There is a time-lag of IFF_RUNNING flag consistency between vlan and
real devices when the real devices are in problem such as link or cable
broken.

This leads to a degradation of Availability such as a delay of failover
in HA systems using vlan since the detection of the problem at real
device is delayed.

We can avoid the linkwatch delay (~1 sec) for devices linked to another
ones, since delay is already done for the realdev.

Based on a previous patch from Mitsuo Hayasaka

Reported-by: Mitsuo Hayasaka <mitsuo.hayasaka.hu@hitachi.com>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: Patrick McHardy <kaber@trash.net>
Cc: "Michał Mirosław" <mirq-linux@rere.qmqm.pl>
Cc: Tom Herbert <therbert@google.com>
Cc: Stephen Hemminger <shemminger@vyatta.com>
Cc: Jesse Gross <jesse@nicira.com>
Tested-by: Mitsuo Hayasaka <mitsuo.hayasaka.hu@hitachi.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bna: Driver Version changed to 3.0.2.1

Signed-off-by: Gurunatha Karaje <gkaraje@brocade.com>
Signed-off-by: Rasesh Mody <rmody@brocade.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bna: SKB PCI UNMAP Fix

Change details:
 - Found a leak in sk_buff unmapping of PCI dma addresses where boundary
   conditions are not properly handled in freeing all Tx buffers. Freeing
   of all Tx buffers is done considering sk_buffs data and fragments can
   be mapped at the boundary.

Signed-off-by: Gurunatha Karaje <gkaraje@brocade.com>
Signed-off-by: Rasesh Mody <rmody@brocade.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bna: TX Queue Depth Fix

sk_buff unmap_array grows greater than 65536 (x2) with Tx ring of 65536.
Reducing TXQ depth and safe(max) acking of Tx events to 32768 (same as Rx).
Add defines for TX and RX queue depths.

Signed-off-by: Gurunatha Karaje <gkaraje@brocade.com>
Signed-off-by: Rasesh Mody <rmody@brocade.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bna: MBOX IRQ Flag Check after Locking

Change details:
 - Check the BNAD_RF_MBOX_IRQ_DISABLED flag after acquiring the bna_lock,
   since checking the flag and executing bna_mbox_handler needs to be atomic.
   If not, it opens up window where flag is reset when it was checked, but got
   set while spinning on the lock by the other thread which is actually
   holding the lock

Signed-off-by: Gurunatha Karaje <gkaraje@brocade.com>
Signed-off-by: Rasesh Mody <rmody@brocade.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bna: Async Mode Tx Rx Init Fix

Change details:
 - Async mode of Tx/Rx queue initialization in BNAD from a task queue context
   runs into non-unique taskq allocation issues. Get rid of Tx/Rx
   initialization from task q context
 - In the attach function, wait for IOC enable, then do Tx/Rx queue
   initialization. Default BNA attributes are used when IOC enable from attach
   fails and values are set to:
   1 TxQ, 1 RxQ, 1 Unicast MAC, 1 RIT entry

Signed-off-by: Gurunatha Karaje <gkaraje@brocade.com>
Signed-off-by: Rasesh Mody <rmody@brocade.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bna: Ethtool Enhancements and Fix

Change details:
 - Add tx_skb counters and NAPI debug counters to ethtool stats.
 - Add rlb stats strings to bnad_net_stats_strings{} array. rlb_stats field
   was added to struct bfi_enet_stats {} but the corresponding name structure
   array for ethtool was not initialized with right strings, even though the
   actual name structure array got expanded. This caused a NULL pointer
   violation and a crash when doing ehtool -S <if_name>.
 - Modify dim timer stop logic to make it dependent on cfg and run flags
 - While setting the ring parameter restore the rx, vlan configuration and
   set rx mode
 - Indentation fix

Signed-off-by: Gurunatha Karaje <gkaraje@brocade.com>
Signed-off-by: Rasesh Mody <rmody@brocade.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bna: Initialization and Locking Fix

Change details:
 - Initialize rx_id to 0 for bnad_cleanup_rx
 - Return -ENOMEM in case if bna_rx_create fails
 - Count the Rx buffer allocation failures in bnad_alloc_n_post_rxbufs()
 - Remove unnecessary initialization of using_dac to false in bnad_pci_probe
 - Release lock if error while doing bna_num_txq_set in bnad_pci_probe

Signed-off-by: Gurunatha Karaje <gkaraje@brocade.com>
Signed-off-by: Rasesh Mody <rmody@brocade.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bna: Formatting and Code Cleanup

Change details:
 - Print log messages when running with reduced number of MSI-X vectors
   and when defaulting to INTx mode.
 - Remove BUG_ONs and header file inclusion that are not needed
 - Comments addition/cleanup
 - Unused code cleanup
 - Add New Line to Print msg in bfa_sm_fault
 - Formatting fix

Signed-off-by: Gurunatha Karaje <gkaraje@brocade.com>
Signed-off-by: Rasesh Mody <rmody@brocade.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bna: TX Path and RX Path Changes

Change details:
 - Add bnad_pci_unmap_skb() API to unmap skb from transmit path and update the
   unmap index. Add more checks for illegal skbs in transmit path. Add tx_skb
   counters for dropped skbs.
 - The unmap_cons index used in bnad_free_txbufs() is incorrectly declared as
   u16. It quickly wraps around and accesses null sk_buff ptr. So using u32 to
   handle unmap_array.
 - Disable and enable interrupts from the same polling context to prevent
   reordering in Rx path.
 - Add Rx NAPI debug counters.
 - Make NAPI budget check more generic.
 - Modify dim timer stop logic to make it dependent on cfg and run flags
 - Handle reduced MSI-X vectors case in bnad_enable_msix.
 - Check for single frame TSO skbs and send them out as non-TSO.
 - Put memory barrier after bna_txq_prod_indx_doorbell().

Signed-off-by: Gurunatha Karaje <gkaraje@brocade.com>
Signed-off-by: Rasesh Mody <rmody@brocade.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bna: Interrupt Polling and NAPI Init Changes

Change details:
 - Remove unnecessary ccb check from bnad_poll_cq
 - Add bnad pointer to rx_ctrl structure, so that bnad can be accessed directly
   from rx_ctrl in the NAPI poll routines, even if ccb is NULL
 - Validate ccb before referencing to it in bnad_msix_rx and bnad_napi_poll_rx
 - Fix the order of NAPI init / uninit in Tx / Rx setup / teardown path:
   a. Kill bnad tx free tasklet ahead of call to bna_tx_destroy()
   b. Call NAPI disable only after call to Rx free_irq(). This makes sure Rx
      interrupt does not schedule a poll when NAPI is already disabled
 - NAPI poll runs before the h/w has completed configuration. This causes a
   crash. Delay enabling NAPI till after bna_rx_enable(). Split NAPI
   initialization into 2 steps, bnad_napi_init() & bnad_napi_enable().

Signed-off-by: Gurunatha Karaje <gkaraje@brocade.com>
Signed-off-by: Rasesh Mody <rmody@brocade.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bna: PCI Probe Fix

Change details:
 - Return error as -EIO if bnad_res_alloc fails
 - Release the configuration lock before registering with net_device layer.

Signed-off-by: Gurunatha Karaje <gkaraje@brocade.com>
Signed-off-by: Rasesh Mody <rmody@brocade.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bna: Naming Change and Minor Macro Fix

Naming changes: rename devid, BNAD_MAX_TXS, BNAD_MAX_RXS,
BNAD_MAX_RXPS_PER_RX to device, BNAD_MAX_TX, BNAD_MAX_RX,
BNAD_MAX_RXP_PER_RX respectively and change all the references.

Macro Fix: Add ioc_isr_mod_set check to bfa_nw_ioc_mbox_regisr macro

Signed-off-by: Gurunatha Karaje <gkaraje@brocade.com>
Signed-off-by: Rasesh Mody <rmody@brocade.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net, rds, Replace xlist in net/rds/xlist.h with llist

The functionality of xlist and llist is almost same.  This patch
replace xlist with llist to avoid code duplication.

Known issues: don't know how to test this, need special hardware?

Signed-off-by: Huang Ying <ying.huang@intel.com>
Cc: Chris Mason <chris.mason@oracle.com>
Cc: Andy Grover <andy.grover@oracle.com>
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

6LoWPAN: call dev_put() on error in lowpan_newlink()

We should release the dev_hold() on error before returning here.

Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

6LoWPAN: use the _safe version of list_for_each

When we kfree(entry) that causes a use-after-free bug so we have to
use list_for_each_entry_safe() safe here.

Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

6LoWPAN: use kfree_skb() instead of kfree()

Use kfree_skb() to free sbk_buffs.

Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

r8169: convert to SKB paged frag API.

Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Cc: Realtek linux nic maintainers <nic_swsd@realtek.com>
Cc: Francois Romieu <romieu@fr.zoreil.com>
Cc: netdev@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>

qlge: convert to SKB paged frag API.

Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Cc: Anirban Chakraborty <anirban.chakraborty@qlogic.com>
Cc: Jitendra Kalsaria <jitendra.kalsaria@qlogic.com>
Cc: Ron Mercer <ron.mercer@qlogic.com>
Cc: linux-driver@qlogic.com
Cc: netdev@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>

qlcnic: convert to SKB paged frag API.

Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Cc: Anirban Chakraborty <anirban.chakraborty@qlogic.com>
Cc: Sony Chacko <sony.chacko@qlogic.com>
Cc: linux-driver@qlogic.com
Cc: netdev@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>

qla3xxx: convert to SKB paged frag API.

Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Cc: Ron Mercer <ron.mercer@qlogic.com>
Cc: linux-driver@qlogic.com
Cc: netdev@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>

qeth: convert to SKB paged frag API.

Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Cc: Ursula Braun <ursula.braun@de.ibm.com>
Cc: Frank Blaschka <blaschka@linux.vnet.ibm.com>
Cc: linux390@de.ibm.com
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: linux-s390@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>

pasemi: convert to SKB paged frag API.

Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Cc: Olof Johansson <olof@lixom.net>
Cc: netdev@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>

ns83820: convert to SKB paged frag API.

Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Cc: netdev@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>

niu: convert to SKB paged frag API.

Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Cc: netdev@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>

netxen: convert to SKB paged frag API.

Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Cc: Sony Chacko <sony.chacko@qlogic.com>
Cc: Rajesh Borundia <rajesh.borundia@qlogic.com>
Cc: netdev@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>

mv643xx: convert to SKB paged frag API.

Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Cc: Lennert Buytenhek <buytenh@wantstofly.org>
Cc: netdev@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>

macvtap: convert to SKB paged frag API.

Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Cc: netdev@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>

ksz884x: convert to SKB paged frag API.

Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Cc: netdev@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>

jme: convert to SKB paged frag API.

Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Cc: Guo-Fu Tseng <cooldavid@cooldavid.org>
Cc: netdev@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>

ibmveth: convert to SKB paged frag API.

Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Cc: Santiago Leon <santil@linux.vnet.ibm.com>
Cc: netdev@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge branch 'master' of git://git.infradead.org/users/linville/wireless-next into for-davem

greth: convert to SKB paged frag API.

In order to avoid long lines also use phys_to_virt(page_to_phys(page)) =>
page_address(page) (since the are effectively the same thing for lowmem pages).

Also dump the frag's size instead of the headlen when dumping a frag.

Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Cc: netdev@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>

gianfar: convert to SKB paged frag API.

Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Cc: netdev@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>

forcedeth: convert to SKB paged frag API.

Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Cc: netdev@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>

enic: convert to SKB paged frag API.

Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Cc: Christian Benvenuti <benve@cisco.com>
Cc: Vasanthy Kolluri <vkolluri@cisco.com>
Cc: Roopa Prabhu <roprabhu@cisco.com>
Cc: David Wang <dwang2@cisco.com>
Cc: netdev@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>

intel: convert to SKB paged frag API.

Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Cc: Jesse Brandeburg <jesse.brandeburg@intel.com>
Cc: Bruce Allan <bruce.w.allan@intel.com>
Cc: Carolyn Wyborny <carolyn.wyborny@intel.com>
Cc: Don Skidmore <donald.c.skidmore@intel.com>
Cc: Greg Rose <gregory.v.rose@intel.com>
Cc: PJ Waskiewicz <peter.p.waskiewicz.jr@intel.com>
Cc: Alex Duyck <alexander.h.duyck@intel.com>
Cc: John Ronciak <john.ronciak@intel.com>
Cc: e1000-devel@lists.sourceforge.net
Cc: netdev@vger.kernel.org
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

cassini: convert to SKB paged frag API.

Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Cc: netdev@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>

bna: convert to SKB paged frag API.

Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Cc: Rasesh Mody <rmody@brocade.com>
Cc: Debashis Dutt <ddutt@brocade.com>
Cc: netdev@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>

benet: convert to SKB paged frag API.

Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Cc: Sathya Perla <sathya.perla@emulex.com>
Cc: Subbu Seetharaman <subbu.seetharaman@emulex.com>
Cc: Ajit Khaparde <ajit.khaparde@emulex.com>
Cc: netdev@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>

atlx: convert to SKB paged frag API.

Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Cc: Jay Cliburn <jcliburn@gmail.com>
Cc: Chris Snook <chris.snook@gmail.com>
Cc: Jie Yang <jie.yang@atheros.com>
Cc: netdev@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>

atl1e: convert to SKB paged frag API.

Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Cc: Jay Cliburn <jcliburn@gmail.com>
Cc: Chris Snook <chris.snook@gmail.com>
Cc: Jie Yang <jie.yang@atheros.com>
Cc: netdev@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>

atl1c: convert to SKB paged frag API.

Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Cc: Jay Cliburn <jcliburn@gmail.com>
Cc: Chris Snook <chris.snook@gmail.com>
Cc: Jie Yang <jie.yang@atheros.com>
Cc: netdev@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>

acenic: convert to SKB paged frag API.

Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Cc: Jes Sorensen <jes@trained-monkey.org>
Cc: linux-acenic@sunsite.dk
Cc: netdev@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>

8139cp: convert to SKB paged frag API.

Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Cc: netdev@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>

3c59x: convert to SKB paged frag API.

Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Cc: Steffen Klassert <klassert@mathematik.tu-chemnitz.de>
Cc: netdev@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>

iwlwifi: iwl-agn-rs.c: remove old comment

this comment refers to some code that was removed.

Signed-off-by: Greg Dietsche <Gregory.Dietsche@cuw.edu>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: defer ath_tx_setup_buffer setup to the first tx attempt during aggr

With sequence number and buffer allocation deferred to when they're needed
for the first time, it becomes much easier to start dropping packets from
the tid queue if necessary, e.g. when latency suddenly increases. This can
lead to some future improvements in buffer management for better latency.

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: move seqno allocation in the tx path to ath_tx_setup_buffer

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: move the sequence number from ath_frame_info to ath_buf

It is only necessary for BAW tracking and moving it to the ath_buf
makes it easier to add further improvements, such as deferring
seqno allocation in the aggregation path.

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>